Fagor FWM714iT
Contents
1. do not carry out this operation when the wash water is at a temperature of over 30 C Important CLEANING THE OUTSIDE The outside of the washing machine should be cleaned with warm soapy water or a gentle cleaning agent Do not use abrasive cleaning products or solvents It should then be thoroughly dried with a soft cloth When there have been spillages of detergent or additives from the dispenser onto the washing machine cabinet clean them up right away as they are corrosive Important 00 q If you detect any problems with your washing machine you will probably be able to rectify them yourself by consulting the following instructions Indicator Problems FO1 No water coming in FO2 Does nat drain or spin dry If this is not the case unplug the appliance and contact the TECHNICAL ASSISTANCE SERVICE CO3 Does not spin dry FO4 Does not start FO5 Call the Technical Assistance Service F10 Never open up the appliance There is no fuse or similar component inside that can be replaced by the user This may be due to the following PROBLEMS E Check the door is properly shut Why won t the washing machine start E The washing machine is not plugged into the mains or there is no voltage in the mains supply The Start Pause button has not been pressed If the washing machine door is not properly shut F04 will appear on the display Why is the washing ma2. C Synthetic mix co delicate colours medium soil on 11 Delicate 60 C Synthetic mix co whi medium soil es fast colou on rs 12 Rinses Cotton cotton mi Synthetic Delicat Wool wool mix Dx YES NO YES 13 Spin drying Cotton cotton mi x Synthetic Delicate Wool wool mix NO YES 14 Normal dry Cotton Linen 15 Delicate dry Synthetic mixed fabrics 16 Drain End Cotton cotton mix Synthetic Delicate Wool wool mix NO ES A Programme for wash and energy consumption assessment in accordance with standard EN60456 press intensive wash button A 80 Max load Wash TURBO TIME PLUS Programme of clothes product 9 Total Approx description consumption duration Kg compartment KWh Litres minutes Normal wash rinses 6 automatic additive absorption if 0 15 49 60 desired and long final spin SHORT wash rinses 1 5 automatic additive absorption if 0 20 30 30 desired and long final spin 6 0 40 49 82 Y amp 6 Normal wash rinses 0 65 49 87 automatic additive absorption if desired and long final spin 6 p 1 02 49 91 6 1 90 55 110 Prewash normal wash rinses 1 45 60 105 6 automatic additive absorption if Y wy desired and long final spin 3 0 15 55 50 3 0 35 55 50 Delicate wash rinses O automatic additi
3. POWER CUTS If there is a power cut when the electricity comes back on the washing machine will continue to run from where it left off it has several hours of memory The same will happen if the ON OFF button is pressed lance using the a gt warnings E Level the washing machine by adjusting the feet to reduce the noise caused by spin drying E Try and wash clothes of different sizes in the same wash programme to favour the distribution of the clothes inside the drum during spin drying E All the models have a safety system for spin drying that prevents spin drying from being carried out if the distribution of the clothes inside the drum is too concentrated This prevents the appliance from vibrating too much If you find that the clothes are not properly wrung out try spin drying them again after having distributed the clothes more evenly in the drum maintenan na cleanin MAINTENANCE After each wash leave the door open for a while to allow the air to circulate freely inside the machine From time to time depending on the hardness of your water it is recommendable to run a full wash cycle using a decalcifying product This will extend the life of your washing machine The washing machine should be disconnected from the mains electricity supply before any cleaning or maintenance is carried out Important Clean the detergent dispenser whenever there is any washing product residue left i
4. of the programme you have to hold the start button down again for at least 3 seconds After 3 seconds the block function indicator will disappear from the display and it will go into pause status The ON OFF button does not cancel the block function 7 WASH PROGRAMME PHASES AND POWER CUTS PROGRAMME PHASES When the programme is running the programme phase and the time remaining for itto end will appear on the display The active phases will appear successively at the top of the display as the programme progresses The time remaining until the end of the programme will also appear on the display It updates at regular intervals but not minute by minute Any option button can be selected provided the wash phase in which it takes effect has not been passed and when the programme accepts the option Pressing the delay button during washing will have no effect on the washer dryer Pressing the start pause button during the wash activates the PAUSE function If the programme is changed on the selector dial during the washing and drying process the washer dryer will go onto PAUSE status and the programme will be cancelled If you need to add or remove a garment press the start pause button and make sure that the water level is not above the door overflow level and that the temperature inside is not high Press the start pause button again to restart the wash from the same cycle phase it had stopped at
5. ELECTRICAL AND ELECTRONIC APPLIANCES When your appliance is of no further use it should not be disposed of together with general domestic waste collection centre run Disposing of waste do means avoiding poss in them to be treated t can be taken free of charge to a specific waste by your local authority or dealers who provide this service mestic appliances separately ible negative consequences for the environment and health derived from incorrect disposal This will enable the materials and recycled obtaining important savings in energy and resources To highlight the obligation of collaborating with selective waste collection the product is marked with a symbol to warn against using traditional containers for disposing of the appliance For further information contact your local authority or the shop where you purchased the product GF Fagor Electrodom sticos S Coop Apartado 49 Tel 943 71 91 00 01 Fax 943 79 68 81 B San Andr s 18 20500 MONDRAGON Guip zcoa www fagor com e mail info Ofagor com 05 06 FAGOR LJ6A028P 1
6. Manual de instalaci n y uso de la lavadora secadora Manuel d installation et d utilisation de le lave linge s chant Manual de instalac o e utilizac o da m quina de lavar secar Washer dryer installation and operation manual A n els DK w _warmings o o o o o oo o o To avoid the risk of fire electric shocks injury or damage when using your washing machine please take the following precautions E This washing machine comes with a manual that includes operating maintenance and installation instructions Please read all the instructions before using the washing machine E Do not wash items that have previously been cleaned washed soaked or treated with petrol solvents for dry cleaning other inflammable substances or explosives as they produce fumes that could catch fire or explode E Do not add petrol solvents for dry cleaning or other inflammable or explosive substances to the wash water as they produce fumes that could catch fire or explode E Do not repair or replace any part of the washing machine or try to carry out any type of servicing unless it is recommended in the maintenance instructions in the manual E Do not climb onto the machine or stand on the open hatch door E Do not use an extension lead or adaptor to connect your washing machine to the mains supply E The machine should only be used for the purpose it is designed for E Follow the washing instructions recom
7. a negative effect exist which are more environment and on the preservation of the nature friendly A fans The use of more detergent than LZ We therefore recommend you follow necessary will not improve you the detergent manufacturer s washing results and apart from costing instructions 3 SELECTING THE WASH AND DRY PROGRAMME using the appliance and practical tips drying screen time button ON programme start spinand time additional detergent dispenser OFF selector pause anti crease delay function button button button button button The procedure for selecting the wash and dry programme is as follows Ka Switch the washing machine on by pressing ON OFF Kb Activate the programme selector by pressing it to release it Kc Select the wash programme by turning the programme selector dial see programme table The procedure for selecting the drying time is as follows Ka Select the drying time by pressing the drying time button The time will appear on the display increasing each time the drying time button is pressed If you select a wash dry option the load must not be over 4 kg 1 5 kg for delicate wash programmes Important using the appliance and practical tips When you select the programme the following information will be displayed 1 Wash and dry programme phases Wash Rinse Spin drying Dry 2 Spin speed 3 Programme n for a few seconds and then programme d
8. achine has been correctly installed we recommend that you pre clean the machine This is to check that the installation the connections and the drainage are all correct and to thoroughly clean the inside of the washing machine before any wash programmes are run see the operating instructions on the following pages Ka Press ON OFF button Kb Select the normal programme at 60 C Kc Press the start pause button using the appliance and practical tips 4 PREPARING GARMENTS FOR WASHING PREPARATION Before placing the clothes in the drum make sure all the pockets are empty Any small objects may block the drain pump Important SORTING THE CLOTHES Make sure beforehand Ka Sort the clothes according to fabric Ds that your and how they are made lt yoon can We recommend using the delicate A washed programmes for sensitive fabrics There TK is a special wool programme for SNE Before using the drying woollens RAS SS programme first check the label on the garment A to make sure it can be K b Sort clothes according to how soiled tumble dried they are e Wash lightly soiled garments using a short programme e Use a programme without prewash for medium soiled garments e Wash heavily soiled garments using a long programme with prewash Ka Sort your clothes according to colour Wash whites and coloured separately We recommend loading the washing machine to its full capacity This means savi
9. and type of fabrics adjusting the levels of water and energy used in order to preserve the environment So although the water level you can see through the hatch may look low there is no cause for concern as washing and rinsing efficiency will still be optimum safety and troubleshooting Why is there still some water This may be because the dispenser needs cleaning This in the dispenser simple operation is described in Maintaining and cleaning the appliance 1 Cleaning the detergent dispenser Why can t open the hatch Washing machines today are provided with safety systems immediately after the wash for users One of them is that the washing machine cannot has finished be opened until it is certain that the drum is quite still This is why the hatch cannot be opened for 2 minutes Why doesn t the remaining time shown on the clock This time is for guidance purposes only and may be affected coincide with the real time by the conditions under which the selected programme is being run e g initial water temperature size of load or unbalance caused by the garments during spin drying left until the selected cycle finishes Other indications E The washing machine can detect other indications When this happens a number of other indicators appear on the display FO5 FO6 F10 Ifthis happens call the Official Technical Service environmental warninas eco note INFORMATION FOR THE CORRECT DISPOSAL OF WASTE
10. ate The information on it is important It is very important to correctly earth the To remove the power cord pull on the washing machine The electrical body of the plug installation plug socket fuses or If the power cord is damaged it must be automatic switch and counter must be replaced by a cord or special unit provided correctly dimensioned for the maximum by either the manufacturer or your after power indicated on the specifications sales service late p With built in washing machines the plug Do not plug the washing machine plug must be accessible after installation into the socket with wet or damp hands Ea 74 4 INSTALLING THE WASHING MACHINE UNDER A KITCHEN WORKTOP AND PRE CLEANING INSTALLATION UNDER A WORKTOP Your washing machine may be fitted underneath a kitchen worktop Ifyou need to remove the washing machine s worktop for safety reasons you need to fit a protection plate which you can obtain from your Dealer or Technical Assistance Service Follow these steps to fit the plate Ka Remove the washing machine work top by taking out the side screws and moving it gently back Kb Take out the screws and remove the parts holding the worktop in place Kc Put the protection plate into place and screw it to the washing machine so it can then be inserted in the place you wish fitting spongy adhesive all around the perimeter first to prevent noise PRE CLEANING When your washing m
11. chine This may be due to the following vibrating or making too much noise E The blocking and transport screws have not been removed E The washing machine has not been correctly levelled safety and troubleshooting Why doesn t the washing Indicator F01 no water coming in this may be due to machine take in water a cut in the water supply a tap turned off or a blocked water inlet filter The possible solutions are as follows wait for the water supply to be reconnected turn on the tap or remove the water inlet hose and clean the filter If this failure is detected F01 will appear on the display Why doesn t the washing is The reasons for the F02 indicator may be the following machine drain or spin dry washing machine drain pump blocked building drainage pipes blocked or incorrect pump electrical connection Solution if the pump is blocked gain access to it as described in section 2 maintaining and cleaning the appliance If this failure is detected F02 will appear on the display Why doesn t the washing machine spin dry This may be due to an uneven distribution of clothes in the drum and may cause an excessive level of vibrations The solution is to select a spin drying programme If this failure is detected C3 will appear on the display Why can t see any water in This is due to the fact that the washing machine is provided the drum during the wash with a system which is able to adapt to the load
12. example when you are not at home and want to delay the spin drying until you get home to prevent the clothes creasing after spin drying and being left in the drum to be removed 5 TIME DELAY SELECTION AND ADDITIONAL FUNCTIONS TIME DELAY Time delay selection button A delay of up to 24 hours can be selected The delay must be selected after choosing the wash programme To select the hours of delay press the clock button Each time the button is pressed the start of washing is delayed by 1 more hour Cancelling the delay To cancel the delay you have to press the clock button successively The delay will be cancelled when 24 hours have been reached and the button is pressed once more If the programme is changed the delay is also cancelled Additional function selection button depending on programmes Ka Thereare3 options easy iron extra rinse and intensive wash Press the button and the desired option will be displayed Eb By pressing the button several times you can choose between several combinations of one two and up to three additional functions at the same time depending on the programme selected Button Easy iron A This option prevents garments from creasing by means of carrying out a special programme with special turns to fluff out the garments after spin drying and make them easier to iron Button Extra rinse E Increases the level of the final rinse obtained in the clothes suitab
13. ke Then securely tighten the connection nut It is important that the drain hose bend is correctly fastened to the outlet to prevent any risk of it becoming detached and causing flooding If your washing machine has a hot water intake connect the hose with the red threaded end to the hot water tap and to the electrovalve with the red filter The washing machine must be connected to the mains water supply using the new supply hoses supplied with the appliance Do not use water supply hoses that have been used before For your washing machine to work properly the mains water pressure must be between 0 05 and 1MPa 0 05 and 10 Kgr cm DRAINAGE CONNECTION It is recommended that you have a fixed drainage outlet 50 to 70 cm from the floor Avoid the drain hose being too tight kinked or restricted 3 LEVELLING THE WASHING MACHINE AND CONNECTING IT TO THE MAINS ELECTRICITY SUPPLY LEVELLING Use the adjustable feet to level the washing machine This will reduce the noise level and prevent it from moving during use Do not bring the feet too far out you will achieve better stability You need to use a spanner for the models that have a nut ELECTRICAL CONNECTION Consult the specifications plate located on the hatch door of the washing machine before making the electrical connections Ensure that the voltage reaching the plug is the same as that on the plate Do not remove the specifications pl
14. le for large loads and garments belonging to people with sensitive skin Increases water consumption Button Intensive wash This option specially recommended for heavily soiled stained clothes achieves better results by extending the normal wash cycle using the appliance If during the additional function selection the programme is changed or the ON OFF button is pressed all the functions selected until then are cancelled 6 STARTING UP AND BLOCK FUNCTION SELECTION using the appliance STARTING UP Start pause button Ka Tostat up the washing machine you have to press the start pause button The minutes remaining until the end of washing and drying will appear on the display at all times p Select BLOCK FUNCTION Block function selection The lock function ensures that the programme will not be affected if any buttons are pressed It is used when children could press the buttons etc The block function should be activated after the wash programme has been selected together with all its options Activating the block function A Ka The block function is activated by pressing the start pause button and holding it down for at least 3 seconds The display will show if it is activated Deactivating the block function Kb The block function is cancelled when the wash programme comes to an end E If you want to deactivate the block NS function before the end
15. mended by the manufacturer of the garment to be washed E Do not turn your washing machine on until you are sure that e lt has been installed in accordance with the installation instructions e All the water drainage mains electricity and earth connections meet the local regulations and or other applicable regulations specifications Power cord Work top Control panel Detergent dispenser Drain hose Stainless steel drum Hatch Accesible filter behind kickplate Adjustable Kickplate feet pirita Water inlet hose 4 UNPACKING AND UNBLOCKING THE WASHING MACHINE UNPACKING Ka Remove the base corner protectors and top cover UNBLOCKING Ka Remove the screws holding the plastic covers to the back of the washing machine Kb Loosen and remove the 3 blocking screws Kc Cover the holes with the plastic covers you have just removed Do not throw the blocking screws away You may need to move the washing machine at a later date SO D S A S as 5 el 92 CONNECTION TO THE MAINS WATER SUPPLY AND DRAINAGE G installation and assembl The water supply hose is inside the drum Ka Kb CONNECTION TO THE MAINS WATER SUPPLY Connect the bent end of the hose to the threaded inlet of the electrovalve located at the rear of the washing machine Connect the other end of the hose to the water inta
16. ngs on water and energy Whenever possible we recommend that you wash garments of different sizes within the same wash programme This improves the washing action and also aids the correct distribution of the garments in the drum when spin drying and the washing machine will therefore be quieter It is a good idea to put small garments in a wash bag 2 USING DETERGENT AND ADDITIVES using the appliance and practical tips DETERGENT AND ADDITIVES Ka Ka Your washing machine s detergent LU LW ob dispenser has three compartments Prewash Wash Fabric softener Kb Put the detergent or additive into the detergent dispenser before starting the wash programme Kc Liquid detergents may also be used in this washing machine An optional detergent dispenser is to be used for this which can be obtained from the Technical Service Network Place this optional dispenser inside the wash compartment The level of liquid must never be higher than the MAX mark printed on the dispenser wall Remember that the amount of detergent to be used will always depend on E The amount of clothes to be washed Ml How heavily the clothes are soiled E The hardness of the water Information on water hardness in your area can be obtained from the competent local authorities We recommend the use of a decalcifying product if the water hardness is high in your area eco note Remember that concentrated detergents you money it will have
17. nside Ka Pull outwards on the detergent dispenser to remove it completely Kb Use warm water and a brush to clean the compartments Kc Also clean the additive compartment siphons having removed them first Once they have been cleaned put them back making sure that they fit right in to the back Put the dispenser back into the washing machine A dirty or incorrectly fitted siphon will prevent the additives from being taken in and leave water inside the compartment at the end of the wash Important 2 CLEANING THE ACCESISBLE FILTER AND THE OUTSIDE maintenance and cleanin CLEANING THE FILTER Clean the accessible filter if the drain pump is blocked by any foreign objects Ka Remove the kickplate by pulling gently on its edges and turning it downwards to release the clips Ifyou do not have access from the side insert a small screwdriver into the three slots at the top of the kickplate in order to get leverage and release the clips Kb Place a container under the drain pump filter to collect any water that comes out of it Kc Half or quarter turn the filter to the left Water will start to come out Kd When all the water has drained out of the washing machine turn the filter several times until it can be completely removed by gently pulling on it Ke Remove the objects or fluff caught in the filter or the drain pump Kf Put the filter and kickplate back in place again To avoid burns
18. uration 4 Additional functions Easy iron Extra rinse Intensive wash There are four types of programme PROGRAMMES Normal programmes Normal Delicate Auxiliary Drying Delicate programmes TO OTTO Auxiliary programmes 1 Normal cold 8 Delicate cold 12 Rinses 14 Normal dry Drying programmes 2 Quick 30 C 9 Delicate 30 C 13 Spin drying 15 Delicate dry 3 Normal 30 C 10 Delicate 40 C 16 Drain End 4 Normal 40 C 11 Delicate 60 C 5 Normal 60 C 6 Normal 90 C 7 Prewash 60 C eco note We recommend you choose a wash r programme without prewash whenever Po possible This will save you money and ERES 79 help protect the environment Programme Recommended temperature Fabric type Normal prog Delicate prog Aux prog Normal cold O o O Cotton Linen delicate colours very light soil YES Quick 30 C Cotton Linen whites colours very light soil YES NO YES Normal 30 C Cotton Linen delicate colours light soil Normal 40 C Cotton Linen fast colours light soil YE Normal 60 C Cotton Linen fast colour medium soil Normal 90 C Cotton Linen whites heavy soi YE Prewash 60 C Cotton Linen whites fast colours heavy so Delicate cold 2 EEE EEK Synthetic mix co delicate colours very light soil on YE Delicate 30 C Synthetic mix co delicate colours light soi on 10 Delicate 40
19. ve absorption if desired and 3 gentle final spin 0 60 55 55 3 1 00 55 70 Rinses automatic additive 6 amp absorption if desired and 0 05 30 23 long final spin 6 Drain and long final spin 0 05 0 10 2 8 48 160 DOME 1827 100 1 5 Delicate dry 1 2 26 95 Drain and end of programme 6 Takes programme to 0 00 0 2 final position NOTE the KWh and litre consumptions and programme durations may vary depending on the type and amount of clothes mains water pressure etc 4 SPIN SPEED SELECTION using the appliance and practical tips SPIN DRYING The wash options must always be selected after choosing the wash programme Any programme change during selection cancels the previously selected options Ka Spin speed selection and anti crease button The selected programme has its own particular spin speed Kb You can change it by repeatedly pressing the spin button The spin speed will gradually be reduced at 100 r p m intervals to 400 r p m for display models On non display models the LED will light up vt Kc Nospin I Press the spin button again to get to the no spin option A programme without a final spin It is used to prevent creasing when washing special fabrics Kd Anti crease option y The wash programme stops on the last rinse with the clothes left in water When the function is deactivated the washing machine continues the programme draining and spin drying Itis used for
Download Pdf Manuals
Related Search