Orient Technologies BTP-2002NP
Contents
1. 2 1 PARTS IDENTIFICATIONS 3 2 SETTING UP THE PRINTER 5 2 1 Unpacking 5 2 2 Connecting the Cables 5 2 2 1 Interface Connector 6 2 2 2 Cash Drawer Connector 8 2 3 Loading the Paper Roll 8 3 SWITCH BUTTON AND LED 11 3 1 Power Switch 11 3 2 Feed Button 11 3 3 LED 11 4 SELF TEST 12 5 HEXADECIMAL DUMP 12 6 SPECIFICATIONS 13 6 1 General Specifications 13 6 2 Auto Cutter Specifications2. 14 6 3 Interface 14 6 4 Electric Parameters of the Power Supply 14 6 5 Environmental Conditions 14 6 6 Reliability 15 6 7 Black Mark Specifications 15 6 8 Overall Dimension 16 7 FEED BUTTON CONFIGURATION 16 BTP 2002NP Installation manual 2 General Safety Information Before installing and using the printer please read the following items carefully Safety Labels Don t touch the cutter and tear bar of printer The print head is a thermal element and it is at high temperature during printing or just after operation therefore please do not touch it and its peripherals for safety reasons The thermal head is an ESD sensitive device To prevent damage do not touch either its printing part or connecting parts Caution Install the printer on a flat and stable place Reserve adequate space around the printer so that convenient operation and maintenance can be performed Keep the printer away from water source Do not use or store the printer in a place exposed to heat of fire moisture serious pollution a
3. Printer cover is open Short long short Slow Print head is overheated Long short long Fast Paper near end No Faster Paper end Short short short Faster Caution The printer can detect the temperature of the print head with thermal resistor If BTP 2002NP Installation manual 12 the temperature of the print head has increased too much the printer will decrease its print speed If the temperature becomes higher than 65 the protection circuit of the printer will force the printer to stop printing at the same time the light and sound signals as described in the table will be given Self test 1 The printer has a self test function that checks the following Control circuit functions Printer mechanisms Print quality Firmware version 2 Starting the self test Press down the FEED button while switching on the printer the printer will start printing the configuration sheet The contents of the self test page vary according to current configuration of printer Before starting the self test make sure that a paper roll has been loaded and the top cover is closed Hexadecimal Dump 1 Hexadecimal dump mode This function prints the data transmitted from the host computer in hexadecimal numbers and in its corresponding characters 2 Entering the hexadecimal dump mode Open the cover and turn the power on while pressing the FEED button or send a GS A command then close the
4. IINNSSTTAALLLLAATTIIO ONN M MAANNUUAALL Single Station Thermal Printer This printer has been manufactured and branded for ORIENT Technologies B V by Shandong New Beiyang Information Technology Co Ltd Design and specifications are subject to change without notice Ask your supplier for technical specifications before purchase and or use Whenever in doubt about safety issues that might arise from using this product please contact the supplier immediately for assistance M Mooddeell BBTTPP 22000022NNPP BTP 2002NP Installation manual 1 Declarations Changes without notice Information in this document is subject to change without notice ORIENT Technologies bv hereinafter referred to as ORIENT Technologies and SHANDONG NEW BEIYANG INFORMATION TECHNOLOGY CO LTD hereinafter referred to as SNBC reserves the right to improve products as new technology components software and firmware become available If users need further data about this product or have any doubt about safety issues that might arise from using it please feel free to contact ORIENT Technologies SNBC or your local agents Copyright No part of this document may be reproduced or transmitted in any form or by any means electronic or mechanical for any purpose without the express written permission of ORIENT Technologies or SNBC Copyright 2007 by SNBC Printed in China Version 1 1 Trademarks Our registered trademarks
5. Mechanism and Hardware Mech amp Hardware Power Supply default normal gt 5 Choices Normal Low power mode Buzzer default enabled gt 4 Choices Enabled Disabled Cutter default enabled gt 3 Choices Enabled Disabled Mark Sensor default disabled gt 2 Choices Enabled Disabled Back to last menu gt 1 BTP 2002NP Installation manual 20 Print Setting Print Setting Code Page default PC 437 gt 7 Choices PC 437 PC 850 PC 852 PC 857 PC 858 PC 860 PC 863 PC 865 PC 866 PC 1252 PC 1257 CR Command default disabled gt 6 Choices Enabled Disabled Right Margin default 9 mm gt 5 Choices 0 mm 1 mm 3 mm 5 mm 7 mm 9 mm Left Margin default 7 mm gt 4 Choices 0 mm 1 mm 3 mm 5 mm 7 mm 9 mm Paper Roll Width default 80 mm gt 3 Choices 57 5 mm 69 5mm 76mm 80 0 mm 82 5 mm Darkness default normal gt 2 Choices Low Normal High Extra high Back to last menu gt 1 BTP 2002NP Installation manual 21 Paper Near end Sensor setting Set Default Configuration Paper sensor settings Stop print when paper low default disabled gt 3 Choices Enabled Paper Low Alarm default enabled gt 2 Choices Enabled Disabled Back to last m
6. Installation manual 5 Setting UP the Printer 2 1 Unpacking Your printer box should include these items If any items are damaged or missing please contact your dealer for assistance 2 2 Connecting the Cables You can connect up the cables required for printing to the printer They all connect to the connector panel on the back printer which is shown below Before connecting any of the cables make sure that both the printer and the computer are turned off BTP 2002NP Installation manual 6 2 2 1 Interface Connector RS 232 serial interface DB25F Pin Signal name Signal direction Function 1 FG Frame ground 2 TXD Output Transmit data 3 RXD Input Receive data 4 RTS Output Same as DTR signal 6 DSR Input This signal indicates whether the host computer can receive data SPACE indicates that the host computer can receive data and MARK indicates that the host computer cannot receive data When DTR DSR control is selected the printer transmits data after confirming this signal except when transmitting data by DLE EOT and GS a When XON XOFF control is selected the printer does not check this signal 7 SG Signal ground 20 DTR Output 1 When DTR DSR control is selected this signal indicates whether the printer is busy SPACE indicates that the printer is ready to receive data and MARK indicates that the printer is busy 2 When XON XOFF
7. are Warnings and Cautions in this manual Warning Items shall be strictly followed to avoid damages to body and equipment Caution Items with important information and prompts for operating the printer Certifications The quality control system of SNBC has been approved of the following certification DNV ISO9001 2000 The environmental control system of SNBC has been approved of the following certification DNV ISO14001 2004 BTP 2002NP has been approved of the following certification WEEE directive 2002 96 EC ORIENT Technologies bv is complying with all aspects of the European Union s WEEE directive 2002 96 EC All the customers and end users can send the products that have reached the end of their lifes and are to be recycled to ORIENT Technologies bv ORIENT Technologies bv will take care of the recycling of these products in an environmentally responsible manner in accordance with WEEE directive BTP 2002NP Installation manual 2 Contact us In CHINA Address No 169 Huoju Rd Weihai Shandong China 264209 Hot line 86 631 5673777 Fax 86 631 5673778 E mail sales newbeiyang com Website www newbeiyang com via Contact button In EUROPE ORIENT Technologies bv Address Meerheide 115 5521 DX Eersel The Netherlands Hot line 31 497 331080 Fax 31 497 386430 Website www orient technologies com via Contact button BTP 2002NP Installation manual 1 CONTENT GENERAL SAFETY INFORMATION
8. control is selected The signal acts the same as when DTR DSR control is selected BTP 2002NP Installation manual 7 Parallel interface Pin Source Function Pin Source Function 1 H NStrobe 19 Signal Ground nStrobe 2 H Data 0 Least Significant Bit 20 Signal Ground Data 1 3 H Data 1 21 Signal Ground Data 2 4 H Data 2 22 Signal Ground Data 3 5 H Data 3 23 Signal Ground Data 4 6 H Data 4 24 Signal Ground Data 5 7 H Data 5 25 Signal Ground Data 6 8 H Data 6 26 Signal Ground Data 7 9 H Data 7 Most Significant Bit 27 Signal Ground Data 8 10 P NAck 28 Signal Ground PError Select and nAck 11 P Busy 29 Signal Ground Busy and nFault 12 P Perror 30 Signal Ground nAutoFd nSelctIn and nInit 13 P Select 31 H NInit 14 H nAutoFd 32 P NFault 15 Not defined 33 Not defined 16 Logic Gnd 34 Not defined 17 Chassis Gnd 35 Not defined 18 P Peripheral Logic High 36 H nSelectIn Ethernet Pin Number Signal Name Function 1 TX Output Data 2 TX Output Data 3 RX Input Data 4 NC 5 NC 6 RX Input Data 7 NC 8 NC BTP 2002NP Installation manual 8 USB interface Pin Number Signal Name Function 1 VBUS 5V 2 DATA Printer data transmit line minus 3 DATA Printer data transmit line plus 4 GND Ground 2 2 2 Cash Drawer Connecto
9. cover The printer first prints Hexadecimal Dump To terminate From this point on all data received by the printer will be printed in hexadecimal numbers and in its corresponding characters NOTES 1 Non printable characters will be printed as 2 In hexadecimal dump mode all commands other than DLE EOT DLE BTP 2002NP Installation manual 13 ENQ and DLE DC4 are not executed 3 Insufficient print data to fill the last line can be printed by pressing the FEED button 3 Ending hexadecimal dumping Hexadecimal dump mode can be ended by turning off the power or press the FEED button three times or reset the printer after printing has finished lt print sample in Hexadecimal Dump mode gt Specifications 6 1 General Specifications 1 Printing method Direct line thermal printing 2 Dot density 203 DPI H 180 DPI V 3 Printing direction Unidirectional with friction feed 4 Printing width max 80mm 2 52 640 dot positions 5 Characters per line default Font A 42 Font B 56 Kanji 21 6 Character spacing default Font A 0 25 mm 0 01 2 dots Font B 0 25 mm 0 01 2 dots Kanji 0 125 mm 0 005 1 dot Programmable by command 7 Printing speed 200 mm s Max 7 3 s 47 3 LPS maximum 4 23 mm feed BTP 2002NP Installation manual 14 6 2 Auto Cutter Specifications Item Parameter Remarks Cutter type Slide cutter Guillo
10. enu gt 1 Set default config Set printer to default config gt 2 Choices Enabled Disabled Back to last Menu gt 1
11. ing blade is completely separated from the stationary blade Then open the top cover to clear paper jam or such the like Caution 1 Usually at the beginning of the knob being turned the moving blade seems to move very slowly However it s moving Therefore keep turning while carefully observing its movement Caution 2 In case of being unable to turn the knob counter clockwise as shown in figure above turn it clockwise Moving blade Abnormal position Moving blade Normal position BTP 2002NP Installation manual 11 Switch Button and LED 3 1 Power Switch The power button a rocker switch turns the power on or off Note Turn the power on only after connecting the power supply 3 2 Feed Button FEED button 1 Pushing this button the printer feeds paper however the FEED button is blocked during the following conditions Paper is end Printer cover is open 2 If you push this button when the printer is in the macro execution standby state the defined macro is executed instead of feeding paper 3 3 LED 1 Power POWER LED Green On Power is on Off Power is off 2 Error ERROR LED Red Blinking indicates one of the three states Error Self test standby state or macro standby state The error LED and buzzer indicate the states of the printer as described in the table below Errors Voice of buzzer LED flash Cutter error paper jam Long short long Fast
12. inter by stepping back through the submenus to the main menu by using the number 1 plus additional press for validation BTP 2002NP Installation manual 17 Parameter Setting by Feed Button Setting Configuration of the Printer Main Menu Print Self Test gt 2 Exit gt 1 Configuration gt 3 Cutter Test gt 4 Sensor Test gt 5 Configuration Mech amp Hardware gt 4 Communi cation gt 3 Exit with Save gt 2 Exit without Save gt 1 Print Settings gt 5 Paper Sensor Setting gt 6 Set Default Config gt 7 BTP 2002NP Installation manual 18 Configuration of the Serial Interface Communication Baud Rates default 9600 bps gt 2 Choices 9600 bps 19200 bps 38400 bps 57600 bps 4800 bps 2400 bps 1200 bps 115200 bps Parity default none 3 Choices None Odd Even Back to last menu gt 1 Data Bits default 8 bits 4 Choices 7 Bits 8 Bits Stop Bit s default 1 Bit 5 Choices 1 Bit 2 Bits Handshak ing default DTR DSR 6 Choices DTR DSR XON XOFF Rx Buffer Size default 4k bytes 7 Choice 4k bytes 45 bytes Data Receive Error default ignored 8 Choices Ignored Print BTP 2002NP Installation manual 19 Setting
13. n for Thermal roll should also meet the following requirements L1 Mark height 5mm L1 10mm L2 Mark length L2 12mm L3 Mark spacing 20mm L3 lt 500mm Mark location Mark can be located in the left middle and right It is only suitable for 80mm paper rolls Reflectivity Mark s reflection rate should be less than 15 some other reflectance should be greater than 85 Marks in the area between there should not be any patterns such as advertising posters etc Note Marks were measured when printing or feeding If the sensor detects the mark height is greater than that default sets default mark height is 8mm printer will report Paper end error BTP 2002NP Installation manual 16 6 8 Overall Dimension FEED Button Configuration Parameter setting configuring by Feed button 1 Hold the FEED button pressed while switching the printer on 2 After the printer has printed the configuration sheet press and hold the FEED button to configure the printer The main menu for the key stroke setting procedure is printed 3 The procedure consists of several sub menus and step by step working is needed 4 With every choice is a number This number indicates the number of times the FEED button has to be shortly pressed After this the choice is validated by an additional but longer press of the FEED button 1 sec 5 After all settings have been done they are stored in the pr
14. nd direct sunlight Do not place the printer on a place exposed to vibration or impact No dew condensation is allowed to the printer In case of such condensation do not turn on the power until the condensation has completely gone away Connect the AC adapter to an appropriate grounded mains outlet Avoid sharing the mains outlet with large power motors and other devices that may cause the fluctuation in voltage Disconnect the AC adapter when the printer is not used for a long time The socket outlet shall be installed near the equipment and shall be easily accessible Don t spill water or other materials on the printer If this happens turn off the power immediately Do not allow the printer to start printing when there is no printer paper installed otherwise the print head and platen roller might be damaged To ensure quality print and normal lifetime use recommended or good quality printer paper Shut down the printer when connecting or disconnecting interfaces connectors to avoid damage to the control board Set the print darkness to a lower grade as long as the print quality is acceptable This will help to lengthen the print head life time The printer should only be disassembled or repaired by a technician who is certified by the manufacturer or by ORIENT Technologies bv Keep this manual safe and at hand for ready reference BTP 2002NP Installation manual 3 Parts Identifications 1 Cutter cover 2 Tear bar 3 Pri
15. nter top cover 4 Power LED Indicating power status ON OFF 5 Error LED The red LED indicates basic information about the status of the printer When the LED is off the printer is operating normally A flashing red LED means the printer needs operator assistance such as paper end 6 Feed button Under normal status no error press it to feed paper To feed long lengths of paper press the key continuously 7 Top cover latch 8 Power switch Turning on off the power for the printer O power is turned off power is turned on 9 Power connector 10 Cash drawer connector 11 Communication interface BTP 2002NP Installation manual 4 12 Cutter acting blade 13 Printer platen 14 Cutter fixed blade 15 Paper end sensor For continuous paper this sensor is used to detect whether the paper roll has run out 16 Paper width adjust module There are 4 long slots at the base of paper holder putting the paper width adjust module in different slot will allow the printer to use different width papers listed as follows 80 0 5 mm 76 0 5 mm 69 5 0 5 mm 57 5 0 5 mm Removing the paper width adjust module will allow a paper width 82 5 0 5mm Caution Paper width adjust module is an indispensable part of printer and should be kept safely 17 Top cover position sensor The sensor is used to detect whether the top cover is closed or not BTP 2002NP
16. r The drawer kick out drive pulses are generated by command The host can retrieve the status of the drawer by using the DLE EOT GS a or GS r commands 1 Pin assignments Pin Number Signal Name Function 1 Frame GND 2 Drawer kick out drive signal 1 Output Data 3 Drawer open close signal Input Data 4 24 V 5 Drawer kick out drive signal 2 Output Data 6 Signal GND 2 Connector model Printer side DuoYuan DY126 6P6C or equivalent User side 6 position 6 contact RJ11 telephone jack 3 Drawer kick out drive signal Output signal Output voltage Approximately 24V Output current 1A or less 2 3 Loading the Paper Roll Note Be sure to use paper rolls that meet the specifications Do not use paper rolls that have the paper glued to the core because the printer cannot detect the paper end correctly Turn off power switch 1 Turn off the printer 2 Open the printer top cover as in following figure 3 Put the paper roll into the paper holder See figure below BTP 2002NP Installation manual 9 Caution Adjust the paper width by adjusting the paper width adjust module according to the paper type used Make sure that the paper roll is cut according to the requirement below before loading Make sure that the heat sensitive side of paper faces the print head and the rolling direction of paper meets the requirements The paper roll should be kept from being loo
17. se Or it may cause paper jam or other malfunction The paper roll should be balanced in the paper holder and not be inclined because it can affect paper auto loading and printing 4 Pull the end of the paper roll out up to the end of the top cover and close the printer cover See figure below Caution Both sides of the printer cover must be pressed down completely fail to do so will influence the normal operation of the printer The edge of paper should not leave at the paper exit as shown in the above figure BTP 2002NP Installation manual 10 5 Tear off the surplus portion of paper by using the tear bar Caution While encountering cutter malfunction due to paper jam or unexpected power loss do not open the top cover of the printer by force since the moving blade of the cutter might blocked the cover Failing to do so might damage the moving blade of the cutter In case the moving blade is blocking the cover of the printer please follow the instructions below to solve the problem 1 Switch off the printer and disconnect the power adapter from the printer 2 Remove the cutter cover as shown in figure below which will expose a small wheel knob 3 If the auto cutter works in full cut mode turn the wheel knob counter clockwise as shown in figure below turn it inversely when partial cut while observing its movement through the paper exit do not stop turning until the mov
18. tine type Cutting time 600ms The time that one cut takes Cutting interval 2s 30 times min Max Paper type Thickness 0 065 0 1mm Thermal paper or paper with the same thickness Operation voltage 24VDC Max static current 1 2A 24V DC Cutter lifetime 1 000 000 cuts with reference paper Full cut or Partial cut 6 3 Interface Serial Interface RS232 Parallel Interface IEEE1284 USB Interface Ethernet Interface WLAN 6 4 Electric Parameters of the Power Supply Item Parameter Supply voltage 24VDC 5 Current consumption Mean approximately 2 5A 12 5 duty ratio Peak Approximately 8 A Ripple amp Noise lt 240mVp p Power Connector 1 Positive 24V 2 GND 3 NC Caution Please use the power supply that is supplied with the printer or an equivalent type 6 5 Environmental Conditions 1 Operating temperature and humidity 5 45 20 80 RH No dew condensation 2 Storage temperature and humidity 40 55 93 RH 40 BTP 2002NP Installation manual 15 6 6 Reliability 1 Life times Thermal head 100 000 000 pulses 100 km Auto cutter 1 000 000 cuts 2 MTBF 360 000 hours 3 MCBF 52 000 000 lines 6 7 Black Mark Specifications Printer can work in the mark paper mode and in accordance with mark to set cutting and the start print location In addition to mark paper need to meet the specificatio
Download Pdf Manuals
Related Search