DeLonghi Magnifica ESAM 4500
Contents
1. The appliance displays CAPPUCCINO OR LATTE and after a few seconds the frothed milk is run off from the milk spout into the cup below Run off stops automatically e The appliance then grinds the beans delivers the coffee and displays the ready message again e The cappuccino is ready Sweeten to taste and if desired sprinkle the froth with a little cocoa powder NOTE 1 While preparing the cappuccino milk or coffee run off can be interrupted by pressing button NOTE 2 To change the quantity of coffee or frothed milk delivered automatically into the cup follow the instructions in section 14 NOTE 3 For hygiene reasons you should never leave the milk container attached to the coffee maker for more than a few minutes place it in a refrigerator after a maximum of 15 minutes If the container empties completely while milk is being delivered remove it and add more milk Put it back in place then press the button to request a cappuccino again NOTE 4 After making the cappuccinos and before removing the milk container you must clean the internal circuits of the container and cover by pressing and holding down the CLEAN button on the milk container lid for at least 8 seconds fig 25 The appliance displays CLEANING 30 13 PREPARING FROTHED MILK WITHOUT COFFEE Remove the lid of the milk container Fill the container with the quantity of milk you want to prepare fig 19 Replace the lid on the milk container2. do not unplug and wait for the display to go off open the service door Fig 14 remove the drip tray and the grounds container Fig 15 and clean them press the two red release buttons on the infuser sideways and towards the centre Fig 28 and pull it out IMPORTANT THE INFUSER CAN ONLY BE REMOVED IF THE APPLIANCE IS OFF ATTEMPTING TO REMOVE THE INFUSER WITH THE APPLIANCE ON MAY CAUSE SERIOUS DAMAGE D e wash the infuser under running water without using deter gents Never wash the infuser in the dishwasher e carefully clean the inside of the appliance To remo ve the coffee stuck to the parts inside the appliance scrape it with a plastic or wooden fork Fig 29 and then pick up Infuser Push the PUSH symbol fully in until it clicks into place all the residues using y After having heard the click check that the red buttons have snapped out Bottom pipe on the infuser a wecuun cleaner The pin must be inserted into the bottom Fig 30 Support Pin pipe on the infuser e replace the infuser by sliding it onto the supports and pin at the bottom then push the PUSH symbol fully in until it clicks into place Check that the two red buttons have snapped out otherwise the door cannot be closed The two red buttons have not snapped out CORRECT INCORRECT e replace the drip tray complete with the grounds container e close the service door NOTE 1 If the infuser is not inserted correc
3. Empty the full container and then put it back under the hot water spout e Press the QK button Hot water is run off from the spout into the container below and the appliance displays RINSING e When the water tank is empty the appliance displays the message RINSING COMPLETE PRESS OA 34 e Press the OK button and refill the water tank with clean water e The descale programme is now terminated and the appliance is ready to make coffee again NOTE if the descaling cycle is interrupted before completion the appliance continues to display the descale message and the programme must be started again from the beginning Empty the water tank rinse fill with clean water and run off a cup of hot water IMPORTANT FAILURE TO DESCALE THE APPLIANCE REGULARLY INVALIDATES THE GUARANTEE 16 4 Changing coffee temperature PTo change the temperature of the coffee proceed as follows e Press the MENU button the light over the button comes on then press the NEXT button repeatedly until the appliance displays HIGH TEMPERATURE e Press the CHANGE button until the appliance displays the required coffee temperature e Press the QK button to confirm the temperature selected e Press the MENU button to exit programming mode or NEXT to change other parameters 16 5 Changing the length of time the appliance remains on The appliance is factory preset to go off automatically one hour after the last coffee has been made The num ber of hours the a
4. at refrigerator temperature about 5 C 41 F e Make sure the intake tube is well inserted into the rubber washer fig 20 and then replace the milk con tainer lid e Remove the hot water spout fig 21 and attach the milk container to the nozzle making sure the arrow on the container lid is lined up with the arrow on the control panel of the appliance fig 22 e Position the milk tube as shown in fig 23 and then place a sufficiently large cup under the coffee and milk spouts fig 23 e Ifyou want to make cappuccino frothed milk coffee place the froth regulator on the word CAPPUC CINO between the and symbols marked on the milk container lid fig 25 To obtain a cappuc cino with little froth position the froth regulator near the symbol To obtain a cappuccino with a large amount of froth position the froth regulator near the symbol e If on the other hand you want to prepare a caffelatte hot milk coffee position the froth regulator on CAFFELATTE fig 25 NOTE If you want hotter caffelatte insert the caffelatte accessory into the milk intake tube J as shown in the figure alongside Then insert the end of the tube into the rubber washer in the milk container lid Do not use the caffelatte nozzle when the milk froth regulator is NOT in the CAF t FELATTE position NOTE You can adjust the quantity of milk froth by moving the regulator to an J intermediate position e Press the button fig 24
5. food conform to EC regulation 1935 2004 3 INSTALLATION After unpacking make sure the appliance is complete and undamaged If in doubt do not use it Contact professionally qualified personnel The packing elements plastic bags polystyrene foam etc should be kept out of the reach of children as they are a safety hazard Place the appliance on a work surface far away from water taps basins and sources of heat After positioning the appliance on the work top leave a space of at least 5 cm between the surfaces of the appliance and the side and rear walls and at least 20 cm above the coffee maker Never install the appliance in environments where the temperature may reach 0 or lower the applian ce may be damaged if the water freezes Make sure the mains voltage corresponds to the voltage indicated on the appliance rating plate Connect the appliance to an efficiently earthed socket with a minimum current rating of 10A only The manufacturer may not be considered liable for possible incidents caused by the failure to adequately earth the mains If the power socket does not match the plug on the appliance have the socket replaced with a suitable type by a qualified professional The power cable on this appliance must not be replaced by the user as this operation requires the use of special tools If the cable is damaged or requires replacing contact an authorised service centre only to avoid all risks e You should personalise wat
6. function The appliance displays READY PRE GROUND xe e Lift the lid in the centre place one measure of ground coffee in the funnel see fig 17 and proceed as described in section 6 You can make just one coffee at a time by pressing the G or W button once only e e After using the appliance with pre ground coffee to go back to making coffee using beans deactivate the ground coffee function by repressing the amp button to prepare the grinder for operation again NOTE 1 Never add the ground coffee when the appliance is off to avoid it from being dispersed inside the appliance NOTE 2 Never add more than one level measure otherwise either the appliance will not make the coffee the ground coffee will be lost inside the appliance dirtying it the coffee will run off in drips and the message GROUND TOO FINE ADJUST GRINDER AND TURN STEAM KNOB will be displayed NOTE 3 When dosing the quantity of coffee to be added use the measure supplied only NOTE 4 Use ground coffee for espresso coffee makers only Do not use coffee beans freeze dried coffee or other materials that could damage the appliance NOTE 5 If the funnel blocks due to moisture inside the appliance or an excessive quantity of pre ground cof fee use a knife to push the coffee down Fig 18 then remove and clean the infuser and appliance as descri bed in paragraph 15 2 Cleaning the infuser 10 PRODUCING HOT WATER e Always make sure the applian
7. spurts The appliance is not plugged in The appliance is on The infuser can only be removed if the appliance is off Too much ground coffee has been added The button has not been pres sed and the appliance has used both the ground coffee added and the cof fee ground by the grinder Ground coffee has been added when the appliance is off The holes in the spouts are clogged with dry coffee The mobile drawer inside the service door is blocked and cannot swing The intake tube is not inserted or is inserted incorrectly The milk container lid is dirty The milk is not cold enough or is not semi skimmed Check that the power cable is plugged into the mains soc ket Turn the appliance off and remove the infuser see section 11 2 IMPORTANT the infuser can only be removed if the appliance is off Attempting to remove the infuser with the appliance on will risk causing damage Remove the infuser and thoroughly clean the inside of the appliance as described in section 15 2 Repeat the opera tion using a maximum of 1 measure of ground coffee Thoroughly clean the inside of the appliance as described in section 15 2 Repeat the operation first pressing the amp button as described in section 9 Remove the infuser and thoroughly clean the inside of the appliance as described in section 15 2 Repeat the ope ration but switch the appliance on first Scrape the holes with a needle see section 15 1 Fig 2
8. the hot water spout fig 4 INSERT TARE WATER SPOUT hot water oo has not been inserted es INSERTINEUSER ASSEMBLY After cleaning the infuser has probably been left out of the coffee maker Insert the infuser see section 15 2 37 LESS LOFFEE GENERIC ALARN The ground coffee funnel is clogged Too many coffee beans or too much ground coffee has been added The inside of the appliance is very dirty Empty the funnel with the help of a knife as described in section 9 note 5 Fig 18 Select a milder taste or reduce the quan tity of ground coffee then run off the coffee again Clean the inside of the appliance tho roughly as described in section 15 2 If the message is still displayed after cleaning contact a service centre 19 PROBLEMS TO BE RESOLVED BEFORE CALLING THE SERVICE CENTRE If the appliance is not working and an alarm light is on the causes of the malfunction can be identified and resolved by referring to section 18 If on the other hand no alarm light is on run the following checks befo re calling the service centre The coffee is not hot The coffee is not creamy enough The coffee runs out too slowly The coffee runs out too quickly The coffee does not come out of one of the spouts When the SY wand W buttons are pressed the appliance does not deliver coffee but only water 38 The cups have not been preheated The infuser is too cold The coffee is gr
9. 7 Thoroughly clean the mobile drawer particularly near the hinges to ensure they are free to swing smoothly Insert the intake tube in the rubber washer in the milk con tainer lid fig 20 Clean the milk lid as described in section 15 3 Use semi skimmed milk at refrigerator temperature If you are still not getting the required results try changing brand of milk 39
10. Attach the milk container to the appliance fig 22 Place a sufficiently large cup under the coffee spout fig 23 If you want to make frothed milk place the froth regulator on the word CAPPUCCINO marked on the milk container lid fig 25 If on the other hand you want to prepare hot milk without froth position the froth regulator to CAFFELATTE fig 25 e Press the D_ button twice within 2 seconds The appliance displays HOT OR FROTAED LI and after a few seconds the frothed milk is run off from the milk spout into the cup below e After run off clean the channels inside the milk container by pressing the CLEAN button as described in the previous section note 4 14 CHANGING THE QUANTITY OF COFFEE AND MILK FOR CAPPUCCINOS The appliance is factory preset to automatically deliver a standard cappuccino To change these quantities proceed as follows e Fill the container with milk up to the maximum level indicated on the container e Press the 2 button for at least 8 seconds then release e The appliance displays MILA FOR CAPPUCCINO PROGRAM QUANTITY and starts to run off milk e Once the required quantity of milk has been run off press the button again Milk delivery stops and the quantity is memorised You should not run off frothed milk for more than 3 minutes at a time e After a few seconds the appliance runs off coffee into the cup and displays COFFEE FOR CAPPUCTING PROGRAM QUANTITY e Once the required
11. F PLEASE WAIT and it goes off Fill the container with coffee beans fig 5 5 TURNING ON AND PREHEATING Press the button fig 6 The appliance displays HEATING UP PLEASE WAIT to indicate preheating is underway Once preheating is completed the appliance displays RINSING PLEASE WAIT and performs an automatic rinse cycle a little hot water is run off from the spouts and is collected in the drip tray below Os a The appliance now displays the ready message READS STANDARD TASTE PREPARING COFFEE USING COFFEE BEANS 1 The appliance is preset to make coffee with a normal taste You can also choose coffee with an extra light light strong or extra strong taste To choose the required taste press the D button fig 7 The selected coffee taste will be displayed Place 1 cup under the spouts to make 1 coffee fig 8 or 2 cups for 2 coffees fig 9 For a creamier cof fee lower the spouts to bring them as close to the cups as possible Fig 10 Press the SS button to make a short coffee fig 11 the button for a normal coffee or the W but ton for a long coffee To make 2 coffees press the button twice within 2 seconds To change the quantity of coffee delivered automatically into the cup follow the instructions in section 7 The appliance now grinds the beans and starts running off the coffee into the cup Once the desired quantity has been reached the appliance au
12. INDICE DESCRIPTION OF THE APPLIANCE see page 3 SAFETY WARNINGS INSTALLATION USING FOR THE FIRST TIME TURNING ON AND PREHEATING PREPARING COFFEE USING COFFEE BEANS CHANGING THE QUANTITY OF COFFEE IN THE CUP REGULATING THE COFFEE MILL 9 PREPARING ESPRESSO COFFEE WITH PRE GROUND COFFEE INSTEAD OF BEANS 10 RUNNING OFF HOT WATER 11 CHANGING THE QUANTITY OF HOT WATER 12 PREPARING CAPPUCCINOS FROTHED MILK AND COFFEE 13 PREPARING FROTHED MILK WITHOUT COFFEE 14 CHANGING THE QUANTITY OF COFFEE AND MILK FOR CAPPUCCINOS 15 CLEANING AND MAINTENANCE 15 1 CLEANING THE COFFEE MAKER 15 2 CLEANING THE INFUSER 15 3 CLEANING THE MILK CONTAINER 16 CHANGING AND SETTING THE MENU PARAMETERS 16 1 SETTING THE CLOCK 16 2 SETTING AUTO START TIME 16 3 DESCALING 16 4 CHANGING COFFEE TEMPERATURE 16 5 CHANGING THE LENGTH OF TIME THE APPLIANCE REMAINS ON 16 6 SETTING WATER HARDNESS 16 7 RESETTING FACTORY DEFAULT SETTINGS 16 8 WASHING PROCESS 17 CHANGING THE LANGUAGE 18 MEANING OF MESSAGES AND WHAT TO DO 19 PROBLEMS THAT CAN BE RESOLVED BEFORE CALLING THE SERVICE CENTRE COON A OaBKR WN IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2002 96 EC At the end of its working life the product must not be disposed of as urban waste It must be taken to a special local authority differentiated waste collection centre or to a dealer provi ding this service Disposing of a household appliance separately avoids possibl
13. S 3 is displayed e Press the QK button to confirm the value The coffee maker is now programmed to provide the descaling warning when necessary based on the actual hardness of the water 35 16 7 Resetting factory default settings reset If you change the original values the factory default values can be reset as follows e Press the MENU button then press NEXT repeatedly until the appliance displays RESET TO DEFAULT NG e Press the CHANGE button and the appliance displays RESET TO DEFAULT YES e Press the OK button to reset the factory default values e The appliance is now reset to the factory default settings and the READY message is displayed 16 8 Washing process This function can be used by technical service personnel only 17 CHANGING THE LANGUAGE To change the language press the CHANGE button for at least 5 seconds until the appliance displays the installation message in various languages To select the required language follow the instructions in section 4 1 36 18 MEANING OF MESSAGE DISPLAYED AND WHAT TO DO FILL TANK GROUND TOG FINE ADJUST MLL AND Z INSERT WATER SPOUT AND PRESS UA ENP TS GROUNDS CONTAINER INSERT GROUNDS CONTAINER ADDO PRE GROUND COFFEE FILL BEANS CONTAINER GESCALE PRESSNEXT CHANGE CLOSE DOOR The water tank is empty or is positioned incorrectly The tank is dirty or encrusted with lime scale The appliance cannot make coffee The coffee runs o
14. button comes on then press the NEXT button repeatedly until the appliance displays CLOCK O8 00 e Press the CHANGE button to set the clock If you hold the CHANGE button down the time is changed rapidly e Press the QK button to confirm the value e Press the MENU button to exit programming mode or NEXT to change other parameters 16 2 Setting auto start time This enables the time the appliance will come on automatically and be ready for use to be programmed e Make sure the clock on the appliance is set as described above Press the MENU button then press the NEXT button repeatedly until the appliance displays START TINE 00 00 e Press the CHANGE button to set the auto start time If you hold the CHANGE button down the time is changed rapidly e Press the QK_ button to confirm the value e Press NEXT once and the appliance displays the message AUTO START NG Press the CHANGE button to modify the function the appliance displays AUTO START SES 33 e Press the QK button to activate auto start NOTE when the appliance is turned off and auto start time is set the symbol A appears alongside the time on the unlit display e Press the MENU button to exit programming mode or NEXT to change other parameters 16 3 Descale Over time the continuous heating up of the water used to make the coffee leads to lime scale building up in the inner circuits of the appliance When the appliance displays the message HESLALE you
15. ce is ready e Make sure the water spout is attached to the nozzle fig 4 e Position a container under the spout fig 3 e Press the 2 button fig 1 The appliance displays HOT WATER and hot water is run off from the water spout into the container below you should not run off hot water for more than two minutes at a time To stop the flow press the button Once the set quantity of hot water has been reached run off stops automatically 11 CHANGING THE QUANTITY OF HOT WATER The appliance is factory preset to automatically deliver 250 ml of hot water To change these quantities pro ceed as follows e Attach the water spout fig 4 e Position a container under the spout fig 3 e Press the button for at least 8 seconds then release The appliance displays HOTWATER PROGRAM QUANTHTS and hot water is run off from the water spout 29 e When the hot water in the cup reaches the required level press the 8 button to memorise the new amount You should not run off hot water for more than two minutes at a time 12 PREPARING CAPPUCCINOS OR CAFFELATTE e Select the taste of the coffee you want to use to make the cappuccino by pressing the 4 button e Remove the lid of the milk container e Fill the container with about 100 grams of milk for each cappuccino to be prepared fig 19 Never exceed the MAX level corresponding to about 900 ml marked on the jug You are recommended to use skimmed or semi skimmed milk
16. e negative consequences for the envi ronment and health deriving from inappropriate disposal and enables the constituent materials to be recovered to obtain significant savings in energy and resources As a reminder of the need to dis pose of household appliances separately the product is marked with a crossed out wheeled dust bin 1 DESCRIPTION OF THE APPLIANCE SEE PAGE 3 A Grinding coarseness regulator Control Panel B Coffee beans container 1 Display C Bean container lid 2 MENU light D Central lid for ground coffee 3 Button to activate or deactivate menu parame E Compartment for measure ter setting mode F Cup warmer tray 4 Button to select ground coffee or if the MENU G Ground coffee funnel light is on to display the next parameter on the H Milk container lid with froth regulator menu I Frothed milk spout 5 Button to rinse the appliance or if the MENU J Milk intake tube light is on to confirm the menu parameters K Nozzle 6 Button to select hot water or if the MENU light L Water tank removable is on to confirm the menu parameters M Milk container 7 Appliance ON OFF button N Power cable 8 Coffee taste selection button O Cup tray 9 One or two cups short coffee button P Measure for pre ground coffee 10 One or two cups normal coffee button Q Drip tray removable 11 One or two cups long coffee button R Hot water spout 12 Cappuccino or frothed milk button S Service door T Coffee grounds c
17. ed even if it is not com pletely full If this is not done when next making coffee the grounds in the container may exceed the maxi mum level and block the appliance NOTE 8 while the appliance is running off coffee never remove the water tank If it is removed it will not be possible to make the coffee and the arna will San GRE GUND ig INSERT WATER SPOUT AND PRESS OA 27 To turn the appliance on again you must insert the water spout fig 4 press the QK button and run off water from the spout for a few seconds If the appliance malfunctions do not contact the service centre straight away The problem can almost always be resolved by following the instructions indicated in paragraphs 18 and 19 If this is not the case or for further explanations contact the customer service by calling the number listed on the sheet enclosed on page pag 2 If your country is not listed on the sheet call the number indicated on the warranty 7 CHANGING THE QUANTITY OF COFFEE IN THE CUP The appliance is factory preset to automatically deliver the following quantities of coffee short coffee 40 ml when the G button is pressed normal coffee 80 ml when the button is pressed long coffee 120 ml when the we button is pressed To change these quantities proceed as follows press the button corresponding to the quantity you want to change Gy je or W for at least 8 seconds then release until the message PROGRAM QUANTITY is di
18. er hardness as soon as possible following the instructions in section 16 6 To correctly learn how to use the appliance when starting it for the first time carefully follow the step by step instructions described in the following paragraphs 4 USING FOR THE FIRST TIME l The first time you use the appliance select the language To set English plug the appliance into the mains socket and wait for the following message to be displa yed PRESS GA TO INSTALLENGLISH While the message is displayed press the QK button fig 1 for at least three seconds until the display shows ENGLISH INSTALLED The appliance then displays the setting message in English If you select the wrong language by mistake fol low the instructions in section 17 to choose the right one After 5 seconds the appliance displays FILL TANK To refill the tank remove fig 2 rinse and fill it with fresh water Never exceed the MAX line Put the tank back and push as far as it will go Place a cup under the hot water spout fig 3 If the water spout is not in place INSERT WATER SPOUT is displayed Attach it as shown in figure 4 making sure the arrow on the spout is lined up with the arrow on the control panel of the appliance fig 4 The appliance now displays PRESS UA Press the OK button fig 1 and after a few seconds a little water is run off from the spout Run off stops automatically 25 J 6 The appliance displays TURNING OF
19. ff too slowly The grounds container is full or missing After cleaning the grounds container has not been replaced With the function selected the pre ground coffee has not been poured into the funnel The coffee beans have run out If the coffee grinder is very noisy this means a small stone in the coffee beans has blocked the mill This indicates the presence of lime scale in the appliance After cleaning the infuser has probably been left out of the coffee maker The service door is open Fill the water tank as described in sec tion 6 note 6 and insert it fully Rinse or descale the tank Insert the hot water spout press the 7 button and run off water from the spout for a few seconds Turn the grinding regulator fig 12 one click clockwise see section 8 Empty the grounds container and clean as described in section 6 note 7 then replace Open the service door and insert the grounds container Add the ground coffee as described in section 9 Fill bean container Contact an authorised De Longhi servi ce centre The descaling procedure described in section 16 3 needs to be performed as soon as possible Leave the service door closed and the infuser out of the appliance then follow the instructions displayed If the service door cannot be closed check that the infuser is inserted cor rectly section 15 2 note 1 E B e The button 8 has been pressed and the Insert
20. k as they will absorb too much heat e Use cups that have been preheated by rinsing them with hot water or by leaving them for at least 20 minutes on the cup warmer tray on top of the appliance with the appliance on NOTE 4 while the appliance is making the coffee delivery can be stopped at any time by pressing the SZ ww or W button as previously selected NOTE 5 as soon as delivery is complete to increase the quantity of coffee simply press and hold the GZ wW or W button as previously selected until the desired quantity is reached this operation must be per formed within 3 seconds from when coffee delivery from the spouts ceases NOTE 6 when the appliance displays FILL TANK the water tank must be refilled or the appliance will not make coffee It is normal for there to be a little water left in the tank when the message is displayed NOTE 7 every 14 single coffees or 7 doubles the appliance displays EMPTSGROUNDS CONTAINER indicating that the grounds container is full and must be emptied and cleaned Until the grounds container has been cleaned the appliance continues to display the message and cannot make coffee To clean open the service door at the front by pulling the spout fig 14 remove the drip tray fig 15 empty and clean Empty the grounds container and clean thoroughly making sure all residues deposited on the bottom are removed IMPORTANT when removing the drip tray the grounds container MUST be empti
21. ontainer removable U Coffee spout adjustable in height V Mobile drawer X Infuser Z Control panel Z1 Caffelatte accessory 2 SAFETY WARNINGS READ THESE INSTRUCTIONS CAREFULLY AND KEEP FOR FUTURE CONSULTATION 24 This appliance is designed to make espresso coffee and heat drinks Use with care to avoid scalds from the water and steam jets or through incorrect use This appliance is intended for domestic use only Any other use is considered improper and thus dange rous The manufacturer cannot be held responsible for any damage caused through incorrect wrong or unrea sonable use When using the appliance do not touch the hot surfaces Use the knobs or handles Never touch the appliance with wet or damp hands or feet The appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance In the event of failure or malfunction unplug the appliance from the mains and do not tamper with it in any way If it requires repair contact an authorised service centre only and ask for original spare parts to be used Failure to respect the above could reduce the safety of the appliance Materials and accessories coming into contact with
22. ound too coarsely Wrong type of coffee The coffee is ground too finely The coffee is ground too coarsely The spout holes are blocked The ground coffee may be blocked in the funnel Heat the cups by rinsing them in hot water or leaving them to rest for at least 20 minutes on the cup warmer tray on the lid see section 6 note 3 Heat the infuser by pressing the x48 button fig 13 befo re making the coffee see section 6 note 3 Turn the grinding adjustment knob one click anticlockwise see section 8 Use a type of coffee for espresso coffee makers Turn the grinding adjustment knob one click anticlockwise see section 8 Turn the grinding adjustment knob one click anticlockwise see section 8 Scrape the remains of dry coffee accumulated with a needle Fig 27 Remove the ground coffee inside the funnel using a knife see note 5 section 9 Then clean the infuser and the insi de of the appliance see description in section 11 2 When the 1 button is pressed the appliance does not come on The infuser cannot be removed for cleaning Pre ground coffee is being used not beans and the appliance does not deliver coffee The coffee does not come out of the spouts but rather around the service door The milk does not run out of the milk spout With frequent use the milk is not satisfactorily frothed The milk is insufficiently frothed or runs off from the spout in irregular
23. ppliance remains on max 3 can be increased as follows e Press the MENU button the light over the button comes on then press the NEXT button repeatedly until the appliance displays OFF AFTER TAGUR e Press the CHANGEbutton to change the number of hours the appliance remains on e Press the OK button to confirm the value e Press the MENU button to exit programming mode or NEXT to change other parameters 16 6 Setting water hardness The descale message is displayed after the appliance has been operated for a factory set period of time cal culated on the basis of the maximum quantity of lime scale which may be contained in the water used If necessary this period of operation can be extended making descaling less frequent by programming the appliance based on the actual lime content in the water used Proceed as follows e remove the Total Hardness Test strip enclosed on page 2 from its packaging then dip it fully in the water for a few seconds Remove it and wait around 30 seconds until it changes colour and a number of red dots are formed e Turn the appliance on by pressing the button fig 6 e Press the MENU button then press the NEXT button repeatedly until the appliance displays WATER AARUNESS 4 e Press the HANGE button repeatedly until the number coincides with the number of red squares on the test strip for example if there are 3 red squares on the test strip press the button until WATER HARD NES
24. quantity of coffee has been run off press the button again Coffee delivery stops and the quantity is memorised The appliance is now re programmed with the new settings and displays READY 15 CLEANING AND MAINTENANCE Before performing any cleaning operations the appliance must have cooled down and must be disconnec ted from the mains power supply Never immerse the appliance in the water it is an electrical appliance Do not use solvents or abrasive cleaning products to clean the appliance A soft damp cloth will suffice The infuser grounds container water tank and drip tray must NEVER be washed in the dishwasher 15 1 Cleaning the coffee maker Clean the grounds container as described in section 6 note 7 whenever it requires emptying The water tank should also be cleaned regularly The drip tray is fitted with a level indicator red showing the level of water it contains When the indicator starts to become visible a few millimetres under the drip tray the drip tray must be emp tied and cleaned Check that the holes in the coffee spout are not blocked To unblock them scrape the dry coffee residues away with a needle fig 27 Clean the nozzle regularly with a sponge as shown in fig 26 3 15 2 Cleaning the infuser The infuser must be cleaned regularly to avoid the build up of coffee encrustations which could cause mal function Proceed as follows e turn the appliance off by pressing the C button fig 6
25. should perform the descale cycle Proceed as follows e make sure the appliance is ready e press the MENU button the light over the button comes on then press the NEXT button repeatedly until the appliance displays DESCALE NG e Press CHANGE and the appliance displays the message DESCALE SES e Press the OK button to start the descale programme e Empty the tank and pour in the contents of one bottle 125 ml of DURGOL descaler plus one litre of water For subsequent descaling use descaler of the same type and brand as supplied availa ble from technical service centres authorised by the manufacturer NOTE Make sure splashes of descaler do not fall onto surfaces sensitive to acid such as marble lime stone and glaze e attach the hot water spout to the nozzle e Place a plastic or glass container with a minimum capacity of 1 5 litres under the hot water spout Fig 3 e press the OK button Descaler runs off from the hot water spout into the container below The applian ce displays APPLIANCE IN DESCALE e the descale programme automatically performs a series of run offs and pauses to remove lime scale depo sits from inside the coffee maker e After about 30 minutes the appliance displays RINSING FILL TANK The appliance must now be rinsed through to eliminate residues of descaling solution from inside the applian ce Proceed as follows e empty the water tank rinse and fill with clean water e Reposition the tank e
26. splayed and coffee is delivered when the coffee in the cup reaches the required level press the same button again to memorise the new amount The appliance is now re programmed with the new settings and displays READY 8 REGULATING THE COFFEE MILL The coffee grinder is preset in the factory to prepare coffee correctly and should not require regulating ini tially However after making the first coffees if you find that coffee delivery is either too fast or too slow in drips the grinding coarseness regulator can be adjusted fig 12 Turning it 1 click 1 number clockwise speeds up coffee delivery without drips Turning 1 click anticlockwise slows down delivery giving a creamier appearance to the coffee These adjustments will only be evident after at least 2 cups of coffee have been run off The grinding coarseness regulator must only be turned when the coffee mill is on Turn one click anticlockwise to obtain slower delivery and a creamier appearance finer ground coffee Turn one click clockwise for faster delivery not a drop at a time coarser ground coffee Coffee has been used to factory test the appliance and it is therefore completely normal for there to be traces of coffee in the mill This appliance is however guaranteed to be new 28 9 PREPARING ESPRESSO COFFEE WITH PRE GROUND COFFEE INSTEAD OF BEANS e Press the amp button fig 16 to select the ground coffee function This disables the coffee mill
27. tly until it clicks into place and the two red buttons have not snap ped out the service door cannot be closed NOTE 2 if it is hard to insert the infuser before inserting it squeeze to size by pressing it vigorously from above and below at the same time as shown in Figure 31 NOTE 3 If it is still hard to insert the infuser leave it out of the appliance close the service door unplug from the mains then plug in again Wait for all the lights to go off after the self diagnosis then open the door and replace the infuser 32 15 3 Cleaning the milk container Proceed as follows e Remove the milk spout fig 32 and intake tube e Remove the froth regulator by pulling it outwards e Wash the container and lid in a dishwasher or in hot soapy water Make sure there are no milk resi dues inside the two holes in the lid of the milk con tainer indicated by the arrows in the figure e Put the froth regulator intake tube and milk spout back in the milk container lid 16 CHANGING AND SETTING THE MENU PARAMETERS After pressing the 1 button when the appliance is ready you can use the internal menu to modify the fol lowing parameters and functions e Clock e Length of time the appliance remains on e Auto start time e Water hardness e Descaling process e Factory default values e Coffee temperature e Washing process 16 1 Setting the clock To set the clock proceed as follows e Press the MENUbutton the light over the
28. tomatically stops delivering the coffee and ejects the grounds into the special container After a few seconds the ready message is displayed again and you can make another coffee To turn the appliance off press the button Before going off the appliance performs an automatic rinse cycle a little hot water runs out from the spouts and is collected in the drip tray beneath Take care to avoid scalds NOTE 1 If the coffee is delivered a drop at a time or not at all turn the grinding coarseness regulator fig 12 one click clockwise see section 8 Turn one click at a time until the coffee is delivered satisfactorily NOTE 2 If the coffee is delivered too fast and is not creamy enough turn the grinding coarseness regulator fig 12 one click anticlockwise see section 8 Avoid turning the grinding coarseness regulator excessively otherwise when you select 2 cups the coffee may run out in drips NOTE 3 Tips to make hotter coffee e When you turn the appliance on if you want to make a short coffee less than 60 cc use the hot rinse through water to preheat the cups If 2 3 minutes have passed since you last made coffee before making coffee again you must preheat the infuser by pressing the button fig 13 Run off the water into the underlying drip tray or alternatively use this water to fill and then empty the cup to be used for the coffee so as to preheat it e Unless preheated do not use cups that are too thic
Download Pdf Manuals
Related Search