Omnitron FlexPoint 10T/2
Contents
1. 4320 000B 11 07 Termination switch When attaching anywhere along a coax cable except at the end the Termination switch should be set to Termination Out factory setting When attaching at the end of a cable it can be set to Termination In When the switch is set to Termination In an external termination must not be attached LED indicators LED Color Description Power Yellow Power applied Jabber Red Jabber condition Coax Rx Green Received data on coax line Coax Col Yellow Collision on coax line UTP Rx Green Received data on UTP line UTP Col Yellow Collision on UTP line UTP Link Green Operational device detected at the far end of UTP Polarity Yellow Polarity reversal was detected and corrected automatically Technical Support If you encounter problems in installing or maintaining this product contact Omnitron Technical Support Phone 949 250 6510 Fax 949 250 6514 Address Omnitron Systems Technology Inc 140 Technology Drive 500 Irvine CA 92618 Email support omnitron systems com URL http www omnitron systems com Notes User Warranty Registration Please register on line http www omnitron systems com or complete both sides and mail or fax this registration form to User Warranty Registration Please register on line http www omnitron systems com or complete both sides and mail or fax this registration for2. Omnitron Systems Technology Inc Ost FlexPoint 10T 2 User Instructions Description The FlexPoint family of Converters supports the IEEE 802 3 and Ethernet Versions 1 0 2 0 standards They convert among 10BASE FL with single mode SM and multimode MM fiber 1OBASE 2 thin coax and 10BASE T twisted pair UTP media types The FlexPoint 10T 2 provides conversion from 10BASE 2 coax to 10BASE T UTP It features coax connector and an EIA TIA 568 RJ45 UTP connector The FlexPoint 10T 2 supports switch selectable Straight through or crossed RJ45 UTP wiring and a switch selectable coax line termination Power Adapter Notice 1 When used in a stand alone configuration this product is intended to be used only with a Listed Direct Plug In Power Unit marked Class 2 and rated at 9VDC 1 Amp 2 This product should always be used only with its enclosed Power Unit Warning The operating description in this Instruction Manual is for use by qualified personnel only To avoid electrical shock do not perform any servicing of this unit other than that contained in the operating instructions unless you are qualified and certified to do so by Omnitron Systems Technology Inc Caution All user required operations can be performed without opening the unit Never attempt to open or remove the cover or tamper with the unit Warranty This product is warranted to the original purchaser against defects in material and wor
3. kmanship for a period of TWO YEARS from the date of shipment A LIFETIME warranty may be obtained by the original purchaser by REGISTERING this product with Omnitron within 90 days from the date of shipment TO REGISTER COMPLETE AND MAIL OR FAX THE REGISTRATION PORTION OF THIS INSTRUCTION MANUAL TO THE INDICATED ADDRESS Or you may register your product on the internet at http www omnitron systems com During the warranty period Omnitron will at its option repair or replace a product which is proven to be defective For warranty service the product must be sent to an Omnitron designated facility at Buyer s expense Omnitron will pay the shipping charge to return the product to Buyer s designated US address using Omnitron s standard shipping method WARNING Before plugging the Power Adapter to any wall outlet or AC power source verify that the power on the unit is appropriate for your AC line voltage source Mounting The Omnitron FlexPoint 10T 2 can be individually wall mounted using a wall mounting kit rack mounted using a 5 Module space saver shelf or inserted in a 14 Module power redundant FlexPoint Powered Chassis When wall mounting or shelf mounting attach the power adapter unit If connecting the UTP cable to a hub or switch set the cross over switch to the straight position factory setting If connecting to a PC or workstation set the switch to the cross over position When connecting the FlexPoin
4. m to Omnitron Systems Technology Inc 140 Technology Drive 500 Irvine CA 92618 USA Fax 949 250 6514 FlexPoint Type Model Purchase Date Serial Number Name Purchased From Address City Company Address Zip Code State 3 ne e oO 2 N 3 g 5 z oe C 23d OO Country Comments and Suggestions Fax Phone E mail Please complete both sides of this form Please complete both sides of this form
5. t 10T 2 at the end of a coax segment attach the coax cable directly into the FlexPoint s BNC coax connector When connecting it along the coax cable not at the end use a T connector to tap into the cable Switch Settings RJ45 Cross Over switch When connecting the UTP to a hub or switch it should be se to Straight Through factory setting When connecting to a PC or workstation it should be set to Cross Over Limitation of Warranty The foregoing warranty shall not apply to defects resulting from improper or inadequate use and or maintenance of the equipment by Buyer Buyer supplied equipment Buyer supplied interfacing unauthorized modifications or tampering with equipment including removal of equipment cover by personnel not specifically authorized and certified by Omnitron or misuse or operating outside the environmental specification of the product including but not limited to voltage ambient temperature radiation unusual dust etc or improper site preparation or maintenance No other warranty is expressed or implied Omnitron specifically disclaims the implied warranties of merchantability and fitness for any particular purpose Exclusive Remedies The remedies provided herein are the Buyer s sole and exclusive remedies Omnitron shall not be liable for any direct indirect special incidental or consequential damages whether based on contract tort or any legal theory Form 040 0
Download Pdf Manuals
Related Search