Chief PWRSKUB flat panel wall mount
Contents
1. WILL ADD BETWEEN 1 2 AND 2 1 DEPTH AND MAY AFFECTLOCATION OF DISPLAY ON THEMOUNT SEE PSB XXXX DRAWING ALSO 302 493 1190 19 40 25 1 00 ALL MEASUREMENTS ARE IN THE FOLLOWING FORMAT MILLIMETERS INCHES Unit Depth Tilt Adjustment Extended Retracted Tilted Up Tilted Down ae eee mg PWRSKU Installation Instructions TOOLS REQUIRED FOR INSTALLATION AND PARTS m Co ED 2S 1 2 613mm A I M x1 Installation Instructions PWRSKU Site Requirements WARNING IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT The figure below identifies the minimum reguirements for installation of display mounts onto a steel stud structure If the structure or its components do not meet these requirements contact the mount manufacturer for specific instructions before attempting installation It should also be noted that no other equipment should be mounted to the same stud 16 or 24 on center Studs Display Mount Installation Location Must be centered on stud If back side of wall is unfinished drywall must be installed to a minimum of one stud left and right of the stud s being used to install the mount Drywall must be secured to studs with screws 12 on2. arm tension If desired tension is present tension adjustment is complete If additional tension adjustment is required repeat steps 2 thru 4 until desired tension is achieved NOTE If changing from a smaller display to a larger display may be necessary to increase swing arm tension Socket Head Capscrew Figure 12 4 Using the adjustment wrench D turn adjustment bar C clockwise to increase swing arm tension or counterclockwise to reduce swing arm tension Small adjustments of 1 8 turn or less are typically all that is required to achieve desired tension See Figure 13 and See Figure 14 10 Installation Instructions DECREASE Figure 14 Installation Instructions PWRSKU 11 PWRSKU Installation Instructions USA International A 8401 Eagle Creek Parkway Savage MN 55378 e CH P 800 582 6480 952 894 6280 AS F 877 894 6918 952 894 6918 Our Mounts Your Vision Europe A Fellenoord 130 5611 ZB EINDHOVEN The Netherlands 31 0 40 2668620 Chief Manufacturing a division of 2 F 31 0 40 2668615 M Milestone AV Technologies Asia Pacific A Room 24F Block D Lily YinDu International Building LuoGang BuJi Town Shenzhen CHINA 8832 000224 RevD RY Th pS B ER lt JS DEF24F 2008 Milestone AV Technologies P 86 755 8996 9226 www chiefmfg com F 86 755 8996 9217 08 08
3. center There must be a minimum of 1 7 8 48mm clearance inside wall Drywall 1 2 100 Ibs max or 5 8 125 lbs max minimum Drywall Thickness 9 Both Sides of Stud 7 Steel Stud 2 x 4 25ga Stud type and structural strength must conform to the North American Specification for the Design of Cold Formed Steel Structural Members 962 S 125 18 C Shaped S Stud Section Figure 1 PWRSKU Mount Installation And Adjustment Mount Installation After determining the site meets the installation requirements 1 Identify desired mounting location on wall 2 Using a stud finder or similar method locate studs 3 Align mounting holes in mount with studs making sure mounting holes are centered on studs See Figure 2 WARNING IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Make sure upper and lower mounting holes are used on both sides of both the upper and lower wall plates See Figure 2 4 Mark location of eight mounting holes on wall 5 Drill eight 1 2 013mm holes See Figure 2 Mounting holes centered on studs Figure 2 6 Hold metal channel on anchor D flat alongside plastic straps andslide channel through hole SeeFigure3 Drywall Plastic Straps Figure 3 Installation Instructions 7 Holding plastic straps on anchor D pull anchor away
4. INSTALLATION INSTRUCTIONS Large Flat Panel Steel Stud Wall Mount Our Mounts Your Vision CHIEF PWRSKU PWRSKU DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief and ClickConnect are registered trademarks of Milestone AV Technologies All rights reserved A IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the LEGEND Tighten Fastener Serrez les fixations Loosen Fastener Aflojar elemento de fijacion Befestigungsteil losen Desapertar fixador Dememrhr
5. Open Ended Wrench Llave de boca Gabelschl ssel Installation Instructions corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for the installation of this kit can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this mount is attached can support five times the combined weight of all equipment WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to this accessory does not exceed 100lbs 45 3 kg if being installed on a wall with a minimum 1 2 thick drywall or 125 lbs 56 7 kg if being installed on a wall with a minimum 5 8 thick drywall Adjust Einstellen Regolare Afstellen Ajuster Phillips Screwdriver Ge Hex Head Wrench lt Installation Instructions PWRSKU WEIG HT CAPACITY Mounting Pattem ee i NO TE CUSTOM INTERFACE BRACKET NOTSHOWN THE CUSTOM INTERFACE BRAC KET NEEDED FOR YOUR DISPLAY 686
6. Secure cables to top arm using two cable ties K 5 Repeat steps 1 through 4 for lower arm WARNING IMPROPER INSTALLATION CAN LEAD TO SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT DO NOT route cables through holes in faceplate Installation Instructions PWRSKU Figure 10 ADJUSTMENTS Roll Adjustment The mount allows for the horizontal alignment Roll of the display to be adjusted up to 2 deg right or left to level the display after installing To adjust Roll 1 Loosen the roll tension adjustment nut located on the back side of the faceplate assembly See Figure 11 2 Level display 3 Tighten roll tension adjustment nut See Figure 11 Figure 11 PWRSKU Swing Arm Tension Adjustment Swing arm tension is pre set at the factory and is adjusted to accommodate displays with weights near the top of the mounts capacity If smaller displays are used it may be difficult to reposition the display after mounting Swing arm tension can be adjusted to compensate for smaller display by The display must be mounted prior to adjusting swing arm tension 1 Locate the adjustment bar H and adjustment wrench J 2 Place adjustment bar H into socket head cap screw located at swing arm pivot point See Figure 12 NOTE The display may need to be repositioned in order to gain access to the tension adjustment screw s 3 Check swing
7. aceplate and pulling outward away from wall See Figure 8 2 While supporting both sides of display align four mounting buttons on display or interface bracket with four mounting holes in faceplate See Figure 8 3 Lower display into place listening for audible click to ensure recessed area of mounting buttons are properly seated in lower area of mounting holes and click lock mechanism has engaged See Figure 8 and See Figure 9 Figure 8 NOTE Holes are provided in the faceplate for use with a padlock or similar locking device if desired In addition the pin and nut may be removed from the upper holes and moved to the lower holes for use as a more permanent locking device See Figure 9 Installation Instructions E Remove pin and nuts and move to lower holes A padlock or bolt may be placed through latch holes Figure 9 CABLE MANAGEMENT WARNING IMPROPER INSTALLATION CAN LEAD TO SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Make sure cables do not run through pinch points 1 Loosen front and rear cable clamps on top arm See Figure 10 2 Thread cable ties K under cable clamps and secure clamps to top arm See Figure 10 3 Route power audio video cables through the cable channel in top arm See Figure 10 allowing sufficient slack in cables for left Right movement of display and swing arm and also swing arm extension and retraction 4
8. from wall until channel rests flush behind wall making sure anchor channel is positioned vertically on stud See Figure 8 Slide plastic cap on anchor D towards wall until flange of cap is flush with wall See Figure 4 Steel Stud Drywall 77 A ENNSSSSSSASNS Plastic Cap NI C D x8 NU Anchor Metal Channel ISS SIDE VIEW Figure 4 9 Snap off plastic straps on anchor at wall by pushing side to side snapping off straps level with flange of plastic cap See Figure 5 10 Repeat steps 6 through 9 for each mounting hole Steel Stud Drywall Plastic SY b L Anchor Metal Channel Plastic Straps SIDE VIEW NN Figure 5 11 Place mount over anchors and align mounting holes in display mount with holes in anchors See Figure 6 12 Place flat washer B onto Phillips pan head screws C 13 Insert Phillips pan head screws C with flat washer B through mounting hole in display mount and into anchor D and tighten until flush against mount DO NOT overtighten See Figure 6 14 Repeat steps 6 through 13 for remaining 7 mounting holes Installation Instructions PWRSKU Cover Installation WARNING IMPROPER INSTALLATION CAN LEAD TO To install channel covers EQUIPMENT FALLING CAUSING SERIOUS PERSONAL 1 Install upper wall channel cover E by tipping cover top INJURY OR DAMAGE TO EQUIPMENT Overtightening of down and positioni
9. ng as shown in figure below mounting hardware can damage the steel studs DO NOT See Figure 7 overtighten mounting hardware 2 Lower bottom of upper wall channel cover E and tap firmly across bottom of channel to lock in place as shown in figure below See Figure 7 3 Install and L H end caps G by aligning tabs on end Steel Stud caps with slots in wall channel and sliding tabs into channel until end cap is flush with wall channel cover cover E 4 Repeat steps 4 through 6 above for lower wall channel Drywall g cover and end caps zH Display Mount Anchor Metal Channel SIDE VIEW Figure 6 END VIEW 9 Figure 7 PWRSKU Display Installation WARNING IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT Displays can weigh in excess of 40 Ibs 18 1kg ALWAYS use two people and proper lifting techniques when installing display WARNING IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT Make sure mounting buttons on display are properly seated in mounting holes in faceplate To install display 1 Move mount faceplate to extended position by grasping f
Download Pdf Manuals
Related Search