Optoma Gray Wolf II
Contents
1. fasten screw FR turn right screw RS clockwise to increase the amount of screen drop Run the screen down to test the stop position If the screen does not drop enough adjust the limit switch again Repeat until the desired position is set When complete fasten middle fasten screw F and small right fasten screw FR SETTING THE UP LIMIT POSITION CAUTION Do not allow the slat bar to become wedged between the roller and case This could damage the fabric and motor Always check that the slat is free to move inside the case screen travels into case too far Make sure middle fasten screw F loosened then loosen small left fasten screw FL Turn left screw LS clockwise to decrease the amount of travel Run the screen up to test the stop position If the screen does not stop properly adjust the limit switch again Repeat until the desired position is set When complete fasten middle fasten screw F and small left fasten screw FR Panoview M Screen does not travel far enough into case Make sure middle fasten screw F loosened then loosen small left fasten screw FL Turn left screw LS counterclockwise to increase the amount of up travel Run the screen up to test the stop position If more travel ie desired adjust the limit switch again Repeat until the desired position is set When complete fasten middle fasten screw F and small left fasten screw FR2. for choosing Panoview screens All screens have passed the strict quality inspection before delivery Read this manual carefully to ensure proper usage Important Attention the installation of the screen the electric wire connection the setting of the limit switches must be made by a trained engineer only SWITCH BOX SWITCH JACK 12V TRIGGER PLUG Motorized screen with IR remote control switch control amp 12v trigger port Technical data Input Voltage 120VAC 60HZ Output Voltage 3A Fuse 1A IR Remote Control Distance lt 8m 15 Horizontal 12V Trigger Jack OD3 4xID1 3 12V Trigger Signal Voltage 7 11VAC or 8 16VDC Current 22mA IR Handset 1pc Switch control 1pc Unpack screen carefully be sure screen is in good condition and check that all accessories are included inside carton Care in mounting and care in correct operation will mean a long and satisfactory life for your Panoview screen Locate the screen where the audience can best see it and where other furnishings in the room permit Check that voltage and frequency marked on screen is in accordance with local power utility It is suggested only to use screen indoor under normal temperature and humidity conditions Remove two pulling locks on the bottom slat bar after the case has been installed Install screen brackets onto ceiling or wall with appropriate hardware QO MOUNT SCREEN TO WALL MOUNT SCREEN TO CEILING Panov
3. Panoview 7 IMPORTANT SAFETY INSTRUCTIONS Basic safety precautions including the following should always be followed Close supervision is necessary when any motorized screen is used by or near children do not leave motorized screen unattended while in use Do not operate motorized screen with damaged cord or if the motorized screen has been dropped or damaged until it has been examined by a qualified service technician Position the cord so that it will not be tripped over pulled or in contact with not surgaces Never yank cord to pull plug form outlet aways grasp plug bu head and pull to disconnect Let appliance cool completely before putting away Loop cord loosely around appliance when stoing To reduce the risk of electric shock do not immerse this motor ized screen in water or other liquids To reduce the risk of electric shock do not disassemble this appliance only a qualifid service technician may service or repair motorized screen lncorrect reassemble can cause electric shock when the motorized screen is used Only use accessory attachment recommended by the manufacturer Use of non manufacturer recommended accessory attachments may viod the screens warranty and release Panoview of all liability Basic electrical safety precautions should always be observed In the event the above mentioned safety precautions are not observed The warranty may be viod and Panoview released of all liability Panoview a G Thank you
4. iew A ELECTRIC CONNECTION Internal wiring has been completed at the factory No additional wiring is necessary Note all wiring related to the screen may only be serviced by a manufacturer approved trained electrical technician Tampering with electrical wiring may void warranty and release Panoview of liability BLACK DOWN RED UP D FUSE C250 R400 AC120V 60HZ CONNECT THE LINE PILLAR C C RELAY UP l MOTO l T YELLOW GREEN SWITCH JACK4 Panoview a M OPERATING INSTRUCTION Remove two pulling locks on the bottom bar first before any operation this is important to prevent motor damage gt Plug in power supply For Switch control Plug in Switch into switch jack Press button to Up position screen goes up Press button to stop position screen stops Press button to down position screen goes down For IR Remote Direct the handset to IR window on screen housing Press the Up Stop Down button on the hand set screen goes Up Stop Down accordingly For 12V trigger Input 12V trigger signal screen goes down Stop this signal screen goes up Electric lock Press the Up amp Down buttons on the IR handset together then all Up amp Down buttons on the switch and IR handset will be locked To be unlocked press Stop button on the IR handset again or unplug the power
5. supply and plug in again Keeping the screen rolled in its protective case when not in use Always examine both front and back of surface before re rolling into case to make certain screen is free of dust dirt or other foreign matter SCREEN ADJUSTMENT Note Adjustments to screen limit positions can only be performed by a trained technician Screen travel is stopped automatically in the down and up positions by limit switches that are preset in the factory If it is necessary to adjust for more or less please follow the steps below for adjustment Disconnect the power supply first before any operation Remove the plate on right bottom side of screen housing 4 PLATE This is important Loosen Fasten Screw F first before adjustment Upper limit switch is on the left side and bottom limit is on the right side Tighten Fasten Screen F after all adjustment FASTEN SCREW F Panoview 7 SETTING THE DOWN LIMIT POSITION To reduce screen drop Make sure middle fasten screw F is loosened then loosen small right fasten screw FR Turn right screw RS counterclockwise to decrease the amount of screen drop Run the screen down to test the stop position If the screen drops too far adjust the limit switch again Repeat until the desired position is set When complete fasten middle fasten screw F and small right fasten screw FR To increase screen drop Make sure middle fasten screw F loosened then loosen small right
Download Pdf Manuals
Related Search