Chief JPP210B flat panel wall mount
Contents
1. a Chiave di sicurezza Veiligheidssleutel Cl de s curit JPP SERIES Installation Instructions TOOLS REQUIRED FOR INSTALLATION b 5 32 3 16 Interface Bracket Kit including hardware 1 4 20 x 1 1 4 Installation Instructions JPP SERIES INSTALLATION IMPORTANT The following installation instructions assume that a 1 1 2 NPT pipe has been properly installed and is in place 1 Determine approximate location for mount keeping in mind display size extension height adjustment if applicable and pitch roll requirements 2 Place mount A against pole with clamp on opposite side of pole See Figure 1 Using 5 32 hex key loosely assemble with three 1 4 20 x 1 1 4 button head cap screws Figure 1 NOTE Equally tighten screws C against clamp B and mount A See Figure 2 x 3 TI We Reep equal distance betvveen AR mount and clamp when tightening A Figure 2 3 Position mount at desired height and orientation Tighten screws securely Display Installation 1 Determine mounting pattern on display WARNING IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND DAMAGE TO EQUIPMENT DO NOT substitute hardware Use only hardware su2. 0 2668615 Office No 1 on 12 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477 DI 4 ul 4 S el ORCONsUMERS
3. INSTALLATION INSTRUCTIONS Medium Panel Pole Mount S CHIEF JPP SERIES Our Mounts Your Vision JPP SERIES Installation Instructions DISCLAIMER Milestone AV Technologies Inc and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions DIMENSIONS WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty It is the installer s responsibility to make sure all components are properly assembled an
4. Marcar com lapis Segno a matita Potloodmerkteken Marquage au crayon Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Drill Hole Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis a pointe cruciforme Adjust Ajustar Einstellen Ajustar Regolare Afstellen Ajuster Open Ended Wrench Llave de boca Gabelschl ssel Chave de bocas Chiave a punte aperte Steeksleutel Cl fourche Remove Quitar Entfernen Remover Rimuovere Verwijderen Retirez By Hand mano Von Hand Com a m o A mano Met de hand la main Optional Opcional Optional Opcional Opzionale Optie En option d y d 2 Hex Head Wrench Llave de cabeza hexagonal Sechskantschl ssel Chave de cabe a sextavada Chiave esagonale Zeskantsleutel Cl t te hexagonale Security Wrench Llave de seguridad Sicherheitsschl ssel Chave de seguran
5. P SERIES Installation Instructions Align two screws in display back with upper mounting holes in Centris cup and lower display until screws are seated in lower area of teardrop mounting holes See Figure 4 Install two more of the same screws through lower mounting holes in Centris cup and into display back See Figure 4 Tighten all hardware Route cables and wires to display Figure 4 ADJUSTMENTS To adjust display Roll Pitch and YAW tension D Disconnect all wires and cable from the display Remove two Lower screws securing display to Centris cup Loosen two Upper screws securing display Lift display upward and away from mount Using a hex head wrench turn the tension adjustment screw clockwise to increase tension or counter clockwise to decrease tension See Figure 5 Re install display Figure 5 Installation Instructions JPP SERIES JPP SERIES Installation Instructions CHIEF Our Mounts Your Vision Chief Manufacturing a products division of Milestone AV Technologies 8832 000238 RevC 2009 Milestone AV Technologies a Duchossois Group Company www chiefmfg com 11 09 USA International Europe Asia Pacific gt TU 8401 Eagle Creek Parkway Savage MN 55378 800 582 6480 952 894 6280 877 894 6918 952 894 6918 Fellenoord 130 5611 ZB EINDHOVEN The Netherlands 31 0 40 2668620 31 0 4
6. d installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components located between the JPP up to and including the display does not exceed 75 Ibs 34 02 kg e The weight capacity of the JPP mount may be LIMITED to the lowest weight capacity of any other component located between the JPP and the supporting structure Chief and Centris are trademarks of Milestone AV Technologies Inc All rights reserved d MEASUREMENTS IN INCHES MILLIMETERS Installation Instructions JPP SERIES LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Pencil Mark Marcar con l piz Stiftmarkierung
7. pplied by manufacturer WARNING IMPROPER INSTALLATION CAN LEAD TO ELECTRIC SHOCK OR DAMAGE TO EQUIPMENT Screw length must not exceed the depth of threaded mounting insert in display WARNING OVERTIGHTENING OF SCREWS CAN DAMAGE PARTS AND LEAD TO SERIOUS PERSONAL INJURY AND DAMAGE TO EQUIPMENT DO NOT over tighten screws when installing interface bracket NOTE If the display being installed has a 100 100 VESA mounting pattern no interface bracket is required and the display can be mounted directly to the Centris cup as outlined below NOTE If the display being installed requires an interface bracket refer to the interface bracket installation instructions WARNING IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Using screws of improper size may damage your display Proper screws will easily and completely thread into display mounting holes Ensure that screws are not too long WARNING IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Inadequate thread engagement in display may cause display to fall Back out screws ONLY as necessary to allow installation of Centris cup 1 Start two M4 x 8mm Phillips pan head screws included in hardware kit into upper mounting holes in display back See Figure 3 NOTE Leave at least 1 8 of each screw protruding out back of display Figure 3 JP
Download Pdf Manuals
Related Search