Chief KTA1042B
Contents
1. Mount Centris Head with Pole Clamp Model FTP Series FTP 220 320 And 440 Assembly To assemble the FTP 220 320 and 440 1 Assemble pole 50 to base 40 using one 3 8 16 x 1 FHCS 90 see Figure 2 2 Assemble pole clamp back 240 to pole mount front using two FW 250 and two BHCS 260 using a 5 32 hex key see Figure 4 3 Secure pole mount back 240 to pole mount front and pole by tightening two BHCS 260 using a 5 32 hex key Pole Pole Mount front with Array Pole Clamp Back 240 Figure 4 Assemble Array Rail to Pole Display Installation Attach Centris Head to Flush Mount Display A CAUTION CAUTION If display uses a screw size other than those included in the kit DO NOT use the screws provided Using the wrong screws could result in damage to your monitor 1 Install two M4 x 12mm Phillips pan head screws 160 into two upper mounting holes in display back see Figure 5 NOTE DO NOT fully tighten at this time 2 Hangdisplay on Centris head see Figure 6 3 Install bottom two M4 x 12mm Phillips pan head screws 160 through Centris head mounting holes and into lower mounting holes in display back 4 Tighten ALL four M4 x 12mm Phillips pan head Installation Instructions screws 160 see Figure 7 Display Figure 7 Secure Display to Centris Bracket Installation Instructions Model FTP Series Attach Centris Head to Recessed Mount Display NOTE Refer to Ta2. Freestand Pole Mounting 3 8 16 x 1 FHCS 100 SCREW Cable Management Grommet Mounting 3 8 16 x 6 CE CE ca E C 190 SPACER Nylon 3 8 used with item 170 200 SPACER Nylon 3 4 used with item 180 210 CLAMP Front Pole Mount CLAMP Rear Pole Mount SCREW Button Head Cap CLAMP Back Array mounting 2 VVASHER Flat 1 4 260 SCREW Button Head Cap 1 4 20 x 3 4 2 Indicates an available optional accessory not included with above models For additional information pertaining to available accessories contact a Chief Customer Service represenatative at 1 800 582 6480 or visit us at www chiefmfg com 1 1 1 1 1 1 1 1 2 1 1 220 230 240 1 50 2 Quantity varies depending upon the number of displays being installed Installation Instructions Model FTP Series 10 Includes 210 220 230 Figure 1 Parts ASSEMBLY AND INSTALLATION 2 Place front pole clamp with Centris Head 210 against pole in approximate mounting location Mount Assembly 3 Place three BHCS 230 into rear pole clamp 220 i and place against pole aligning with front pole clamp FTP 230 Assembly 210 see Figure 3 To assemble the FTP 230 4 Secure rear pole clamp 220 to front pole mount 1 Assemble pole 60 to base 40 using one 3 8 16 x 1 210 and pole by tightening three BHCS 230 using FHCS 90 see Figure 2 5 32 hex key 120 see Figure 3 Figure 2 Assemble Pole to Base Figure 3
3. INSTALLATION INSTRUCTIONS Horizontal And Vertical Table Stands and Accessories Model FTP Series The FTP Series is a free standing pole mount solution for multiple displays FTP 220 FTP 225 FTP 440 FTP 230 BEFORE YOU BEGIN A CAUTION To prevent damage to the Kit which could affect or void the Factory warranty and to the equipment that will be attached to it thoroughly study all instructions and illustrations before you begin the installation If you have any questions about this installation contact Chief Manufacturing at 1 800 582 6480 CHIEF MANUFACTURING INC 8832 000144 Rev E MN 1 800 582 6480 952 894 6280 FAX 952 894 6918 2007 Chief Manufacturing iC 8401 EAGLE CREEK PARKWAY STE 700 www chiefmfg com SAVAGE MINNESOTA 55378 USA 05 07 Model FTP Series Installation Instructions TOOLS REQUIRED FOR INSTALLATION e Phillips Head Screw Driver e 93 4 Wrench e 3 32 Hex Key provided e 5 32 Hex Key provided e 7 32 Hex Key provided PARTS Carefully inspect components for shipping damage If damage is apparent call your carrier claims agent and do not continue with installation until the carrier has reviewed the damage see Figure 1 Table 1 Parts QUANTITY By MODEL ITEM FTP 225 FTP 230 FTP 320 FTP 440 CENTRIS HEAD ASSEMBLY Pole Mon ARRAY ASSEMBLY Triple Ss 10 20 30 40 50 70 POLE Freestand 28 POLE Freestand 42 SHEATH Cable Management 8 SCREW
4. ble 3 to select the applicable screw Phillips Pan Head Screw and spacer combination 170 or 180 1 Uninstall end lock using the 5 32 hex key 120 see Figure 8 2 Remove Centris head from array rail 20 30 Centris Head Spacer 190 or 200 Centris Head Square Nut TT Display End Lock Figure 10 Mount Centris Bracket to Display 7 Slide display with Centris bracket onto array rail 20 30 see Figure 11 NOTE Repeat previous steps for each additional display 8 Reinstall end locks into mounting rail using the 5 32 hex key 120 see Figure 12 Display with Centris Bracket Centris Head Figure 9 Slide Centris Bracket off Array Rail Place display face down on a clean dry surface 4 Place four 3 8 or 3 4 nylon spacers 190 or 200 over four mounting holes in display back see Figure 10 5 Align Centris head mounting holes with four nylon spacers see Figure 10 Figure 11 Mount Display with Centris Bracket to 6 Secure Centris head to display using four Array Rail M4 x 20mm Phillips pan head screws 170 or four M4 x 30mm Phillips pan head screws 180 see Figure 10 Model FTP Series End Lock Retaining Screw Centris Head Figure 12 Reinstall End Lock s ADJUSTMENTS Display Adjustment The FTP Series mount allows horizontal pitch and rotational adjustment of each display The FTP Series mount also allows a full 360 deg of display rotation with a max
5. imum pitch range of 15 up and 15 down Display Horizontal Position Adjustment To adjust display horizontal position 1 Loosen Centris bracket rear adjustment knob see Figure 13 2 Slide Centris bracket with display left or right until properly positioned on array rail 3 Tighten Centris bracket rear adjustmnent knob Figure 13 Display Horizontal Adjustment Installation Instructions Display Pitch and Roll Adjustment To adjust display pitch or roll position 1 Loosen Centris bracket front adjustment knob see Figure 14 2 Tilt display up or down or adjust display roll left or right until properly positioned 3 Tighten Centris bracket front adjustmnent knob Pitch Roll Adjustment CABLE MANAGEMENT The FTP Series mount includes cable management features used to properly route and secure display cables To use the cable management features 1 Connect cables to display 2 Route cables through cable clips on array rail 3 Route cables down pole and away from mount and secure to pole using sheath 80 Cable Clips mr TITEL KI II NN 7 Figure 15 Cable Management Installation Instructions Model FTP Series Model FTP Series Installation Instructions
Download Pdf Manuals
Related Search