Chief PPD2000
Contents
1. INSTALLATION INSTRUCTIONS Plasma Presenters Dual Display Video Conferencing Cart PPD Series The PPD is a highly functional video conferencing solu tion The cart provides agile mobility for two Large Flat Panel Displays side by side with a combined weight of up to 200 pounds Optional equipment shelves and video conferencing accessory shelves can be easily added for a complete system Using Chief s exclusive ClickConnect M Mounting Sys tem for easy installation the cart provides stable mount ing quick release and optional security Additionally its streamline shape eliminates trip hazards and allows the display to roll smoothly up to a conference table Large swivel casters with lock brakes pitch adjustment and cable management make the cart user friendly BEFORE YOU BEGIN CAUTION To prevent damage to the cart which could affect or void the Factory warranty thoroughly study all instructions and illustrations before you begin to install or operate the unit Pay particular atten tion to the Important Warnings and Cautions on Page 2 e he maximum weight to be installed on the PPD is 200 pounds 90 72 Kg e f you have any questions about this assembly contact Chief Manufacturing at 1 800 582 6480 or 952 894 6280 Chief amp and ClickConnect are trademarks of Milestone AV Technologies All rights reserved l i VIE 8809 000004 Rev E O i Chief Manufacturing a division of Milestone AV Te2. apparent call your carrier claims agent and do not continue with the assembly proce RART rei T 4 dure until the carrier has revievved the damage ASSEMBLE CART cessant 6 MOUNT PLASMA DISPLAYS ON CART 8 OPTIONAL ACCESSORIES e Acrylic Shelf e Video Conferencing Shelf TOOLS REQUIRED FOR INSTALLATION 7 16 and 3 4 wrench e Allen wrenches e Socket set with extension NOTE Other tools may be required depending on the method of installation Installation Instuctions PPD Series PARIS Table 1 Parts List se pescano CC cass Howtos N mum lum 01 75 SCREW Cap Button head 1420x518 Dx cenae Xinh IS enu 4 EST TE ESC EC ESC mena e sem p p LS Cm wm me rem a LES EAC SET ff Cw SPREADER maons 3 E ELLE dea pa dE p 90 160 PPD Series Installation Instuctions PARTS CONT D Installation Instuctions ASSEMBLE CART NOTE Read all instructions before assembly Also refer to Table 1 on page 4 and PARTS on page 4 for the numbers shown in parenthe sis 1 Place base 100 upside down see Figure 1 a Thread two regular casters 10 into the holes near the corner support posts in the base front as shown in Figure 1 Thread two locking casters 20 into the holes at the end of the support posts for the base front as shown in Figure 1 2 Place ba
3. chnologies 2008 Milestone AV Technologies 8401 Eagle Creek Parkway Savage MN 55378 www chiefmfg com Our Mounts Your Vision P 800 582 6480 952 894 6280 F 877 894 6918 952 894 6918 05 08 Installation Instuctions PPD Series WARNING CAUTION e WARNING e WARNING e WARNING e CAUTION e CAUTION IMPORTANT WARNINGS and CAUTIONS A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions Do not attempt to hang the plasma displays onto the cart alone Always use two people to mount each display Always park the cart on a level surface The locking wheels of the cart are not designed to hold the cart on an inclined surface Do not use the cart to transport your plasma displays on ramps or steep angles The cart is designed to move on smooth flat surfaces Inspect the unit for shipping damage Do not use cleanser or harsh cleaning agents on acrylic shelves Installation Instuctions PPD Series CONTENTS INSPECT PARTS BEFORE ASSEMBLY INSPECT PARTS BEFORE ASSEMBLY 3 e Refer to Table 1 on page 4 and PARTS on page 4 OPTIONAL ACCESSORIES 3 Carefully inspect the parts for shipping damage TOOLS REQUIRED FOR INSTALLATION is
4. ecuring tilt head spreaders 90 adjust tilt head to desired angle 0 to 7 1 22 and tighten four 1 4 20x5 8 button head cap screws 130 See Figure 5 Loose Loosen Screws 4 0 to 7 5 Degrees 6 4 Tilt Mounting Head 70 Dual Screen Mounting Bracket Figure 5 Adjust Tilt Mounting Head 7 Using six 5 16 18X3 4 screws 140 secure the dual screen mounting bracket 80 to the tilt mounting head 70 see Figure 6 e Dual Screen Mounting Bracket 80 Tilt Mounting Head 70 Figure 6 Attach Dual Screen Mounting Bracket to Mounting Head Installation Instuctions PPD Series MOUNT PLASMA DISPLAYS ON CART 1 Measure the distance from the center of your display to its outermost edge NOTE Make sure to leave some space between displays when mounted 2 Using the measurement found in Step 1 and the faceplate 50 as a template measure from the cen ter of the dual screen mounting bracket 80 to find the correct mounting holes for your application see Figure 7 3 Secure each face plate 50 using four 1 4 20x5 8 screws 130 see Figure 8 Dual Screen P Mounting Bracket 80 Figure 8 Dual Mounting Head with Face Plates Attached Installation Instuctions PPD Series MOUNT PLASMA DISPLAYS ON CART CONT DJTo install display WARNING Make sure cart wheels are locked before installing the display to the cart MEN 722 4 While supporting both
5. se 100 upright on casters 3 Install legs for base 100 as follows a Insert left leg 110 and right leg 120 into the support posts on the base Make sure the mounting tabs face inward see Figure 2 Secure both legs using two washers 150 and two 1 4 x 1 2 screws 130 Install cap plugs 30 in base see Figure 3 Install cap plugs 40 on top of left leg 110 and right leg 120 See Figure 4 4 Using two 1 4 20 x 5 8 button head screws 130 one on each side secure the mounting head 70 to the top of the legs 110 and 120 of the cart see Figure 4 5 Using four 1 4 20 x 5 8 button head screws 130 two on each side secure two tilt head spreaders 90 one per side see Figure 4 Install 1 4 20 screw 130 securing mounting head on each side first threads into mounting head PPD Series hs 10 Front Casters 20 Rear Casters Locking Left arm Example Figure 1 Install Casters Mounting tabs face inward Figure 2 Turn Mounting Tabs Inward 30 Posts may need to be Cap Plug lifted slightly to insert with star cut fasteners 130 and 150 Figure 3 Install Legs Cap Plug 40 1 4 20 Screws 130 Securing Tilt Plate Figure 4 Install Mounting Head Installation Instuctions PPD Series ASSEMBLE CART CONT D 6 Adjust tilt head 70 to desired tilt by slightly loosen ing four 1 4 20x5 8 button head cap screws 130 s
6. sides of display align four 4 2 mounting buttons on display or interface bracket more permanent lock f with four mounting holes in faceplate remove pin and nuts and See Figure 9 move to lower holes 5 Lower display into place listening for audible click to ensure recessed area of mounting buttons are properly seated in lower area of mounting holes and ClickConnect mechanism has engaged See Figure 9 and See Figure 10 A padlock or bolt may be placed through latch holes Figure 10 Secure Display Figure 9 Hang Display NOTE Holes are provided in the faceplate for use with a padlock or similar locking device if desired In addition the pin and nut may be removed from the upper holes and moved to the lower holes for use as a more permanent locking device See Figure 10 Installation Instuctions PPD Series G GG 10 Installation Instuctions PPD Series FE U MTM E 11 C CONSUMER
Download Pdf Manuals
Related Search