Chief MWH6364B flat panel wall mount
Contents
1. AS A 0 na G 4 5 16 x 2 1 2 MWH Installation Instructions DIMENSIONS NOTE CUSTOM INTERFACE BRAC KET MEUM NN NOTSHOWN THE CUSTOM INTERFACE BRACKET NEEDED FOR YOUR DISPLAY Mounting Pattem a WILL ADD BETWEEN 1 2 AND 2 IN DEPTH TILT ROLL YAW 57 15 5257 0 AND MAY AFFECTLOCATION OF DISPLAY 114 ON THE MOUNT SEE M SB XXXX DRAWING ALSO waw i 58 2 30 397 457 15 65 18 00 Y M 7 2 51 ALL MEASUREMENTS ARE IN THE FOLLOWING FORMAT MILLIMETERS INCHES Unit Depth Tilt Adjustment Extended Retracted Tilted Up Tilted Down Ti 4 Sal 5 UN E MU 25 Figure 1 Installation Instructions MWH Mount Installation and into pilot hole See Figure 3 9 Tighten all hardware DO NOT overtighten WARNING IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT It is the installer s responsibility to make sure the structure to which the MWH is being installed is capable of supporting five times the combined vveight of the mount and all attachments 1 Determine mounting location taking into consideration display size and mount movement 2 Using a stud sensor locate stud See Figure 2 3 Using two people place mount2. end caps F by aligning tabs on end caps F with slots in wall channel covers B and sliding tabs in until end caps F are flush with wall channel covers See Figure 4 END VIEW Figure 4 Installation Instructions Display Installation If the mounting pattern of the display being installed is a VESA standard 200 x 200 pattern the mounting buttons can be installed directly to the back of the display If the display has any other mounting pattern an interface bracket must be obtained before proceeding Consult a Chief Customer Service representative if an interface bracket is required by calling 1 800 582 6480 or visit www chiefmfg com WARNINQ IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT Displays can vveigh in excess of 40 Ibs 18 1kg ALWAYS use two people and proper lifting techniques when installing display WARNING IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT Make sure mounting buttons on display are properly seated in mounting holes in faceplate To install display 1 Move mount faceplate to extended position by grasping faceplate and pulling outward away from wall See Figure 5 2 While supporting both sides of display align four mounting buttons on display or interface bracket with four mounting holes in facep
3. 96 9217 A Asia Pacific 3 b consumer
4. INSTALLATION INSTRUCTIONS Medium Flat Panel Wall Mount CHIEF Our Mounts Your Vision MWH DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document IMPORTANT VVARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions LEGEND Tighten Fastener Loosen Fastener Open Ended Wrench o Installation Instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warra
5. against wall and level mount aligning mounting holes in upper and lower wall channels with stud See Figure 2 NOTE Horizontal location can be adjusted right or left as long as the upper and lower mounting holes align with one another on stud 4 Use a pencil mark two mounting holes making sure mounting holes are located as close as possible to center of stud See Figure 2 5 Drill two pilot holes where the mounting holes were marked using a 7 32 6mm drill bit See Figure 2 6 Install one 5 16 x 2 1 2 lag bolt G and one 5 16 flat washer H through mounting holes in upper wall channel and into pilot hole DO NOT tighten at this time See Figure 3 7 Using two people place mount against wall aligning Mounting holes mounting holes in upper wall channel with lag bolt and hang centered on mount on lag bolt making sure washers are located in front studs of mount 8 Install one 5 16 x 2 1 2 lag bolt G and one 5 16 flat washer H through mounting holes in lower wall channel Figure 2 Figure 3 MWH Installation Instructions Cover Installation To install channel covers 1 Install upper and lower wall channel covers B by tipping cover top down and positioning as shown in end view of figure below See Figure 4 2 firmly across bottom of channels to lock in place as shown in figure below See Figure 4 3 Install four R H and L H
6. ate MWH Installation Instructions From Display Figure 7 ADJUSTMENTS Pitch Tension Adjustment To adjust display pitch tension 1 With display installed tighten or loosen two screws one on each side using the 5 32 hex wrench See Figure 8 2 Check for desired tension 3 Repeat Steps 1 and 2 until desired tension is obtained Figure 8 Installation Instructions Roll Adjustment The MWH allows for the horizontal alignment Roll of the display to be adjusted up to 2 deg right or left to level the display after installing To adjust Roll 1 Loosen the roll tensions adjustment nut located on the back side of the faceplate assembly See Figure 9 2 Level display 3 Tighten roll tension adjustment nut See Figure 9 Figure 9 Swing Arm Tension Adjustment Swing arm tension is pre set at the factory and is adjusted to accommodate displays with weights near the top of the mounts capacity If smaller displays are used it may be difficult to reposition the display after mounting Swing arm tension can be adjusted to compensate for smaller display by The display must be mounted prior to adjusting swing arm tension 1 Locate the adjustment bar H and adjustment wrench J 2 Place adjustment bar H into socket head cap screw located at swing arm pivot point See Figure 10 NOTE The disp
7. late See Figure 5 3 Lower display into place listening for audible click to ensure recessed area of mounting buttons are properly seated in lower area of mounting holes and click lock mechanism has engaged See Figure 5 and See Figure Figure 5 NOTE Holes are provided in the faceplate for use with a padlock or similar locking device if desired In addition the pin and nut may be removed from the upper holes and moved to the lower holes for use as a more permanent locking device See Figure 6 MWH E Remove pin and nuts and o move to lower holes A padlock or bolt may be placed through latch holes Figure 6 CABLE MANAGEMENT WARNING IMPROPER INSTALLATION CAN LEAD TO SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Make sure cables do not run through pinch points 1 _ Loosen front and rear cable clamps on top arm See Figure 7 2 Thread cable ties E under cable clamps and secure clamps to top arm See Figure 7 3 Route power audio video cables through the cable channel in top arm See Figure 7 allowing sufficient slack in cables for left Right movement of display and swing arm and also swing arm extension and retraction 4 Secure cables to top arm using two cable ties E 5 Repeat steps 1 through 4 for lower arm WARNING IMPROPER INSTALLATION CAN LEAD TO SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT DO NOT route cables through holes in facepl
8. lay may need to be repositioned in order to gain access to the tension adjustment screw s 3 Check swing arm tension If desired tension is present tension adjustment is complete If additional tension adjustment is required repeat steps 2 thru 4 until desired tension is achieved NOTE If changing from a smaller display to a larger display may be necessary to increase swing arm tension Socket Head Capscrew Figure 10 MWH Using the adjustment wrench D turn adjustment bar C clockwise to increase swing arm tension or counterclockwise to reduce swing arm tension Small adjustments of 1 8 turn or less are typically all that is required to achieve desired tension See Figure 11 and See Figure 12 DECREASE Figure 12 MWH 10 Installation Instructions Installation Instructions MWH 11 MWH CHIEF Qur Mounts Your Vision Chief Manufacturing a division of Milestone AV Technologies 8831 000009 Revi 2008 Milestone AV Technologies www chiefmfg com 07 08 Installation Instructions USA International A 8401 Eagle Creek Parkway Savage MN 55378 800 582 6480 952 894 6280 F 877 894 6918 952 894 6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN The Netherlands P 31 0 40 2668620 F 31 0 40 2668615 A Room 24F Block D Lily YinDu International Building LuoGang BuJi Town Shenzhen CHINA 27 PONI A El AS A JE 86 755 8996 9226 F 86 755 89
9. nty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for the installation of this kit can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this mount is attached can support five times the combined weight of all equipment WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to this accessory does not exceed 100 Ibs 45 36 kg Chief amp and ClickConnect are trademarks of Milestone AV Technologies All rights reserved Adjust Ajustar Einstellen Ajustar Regolare Afstellen Ajuster Hex Head Wrench Llave de cabeza hexagonal Sechskantschl ssel Chave de cabe a sextavada Chiave esagonale Zeskantsleutel Cl t te hexagonale Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis pointe cruciforme MWH Installation Instructions TOOLS REQUIRED FOR INSTALLATION AND PARTS 7 32 0 6mm I M j CL y y 7 gt O Va CN
Download Pdf Manuals
Related Search