Silverstone ST60F
Contents
1. EN 61000 4 2 1995 7 2 ELECTRICAL FAST TRANSIENT BURST EFT B EN 61000 4 4 1995 7 3 SURGE EN 61000 4 5 1995 7 4 POWER FREQUENCY MAGNETIC FIELD EN 61000 4 8 1993 7 5 VOLTAGE DIPS RN 61000 4 11 1994 7 6 RADIATED SUSCEPTIBILTY EN 61000 4 3 1996 7 7 CONDUCTED SUSCEPTIBILTY EN 61000 4 6 1996 7 8 VOLTAGE FLUCTATION EN 61000 3 3 1995 7 9 EN61000 3 2 harmonic current emissions If applicable to sales in Europe the power supply shall meet the requirements of EN 61000 3 2 Class D and the Guidelines for the Suppression of Harmonics in Appliances and General Use Equipment Class D for harmonic line current content at full rated power 7 10 EN55022 Class B Radio interference CISPR 22 7 11 FCC Part 15 Subpart J class B 115VAC operation 8 MTBF 8 1 MTBF MEAN TIME BETWEEN FAILURES CALCULATION The demonstrated MTBF shall be 100 000 hours of continuous operation at 25 C full load 80 confidence limit and nominal line The MTBF of the power supply shall be calculated in accordance with MIL STD 217D E The DC FAN is not included 9 MECHANICAL REQUIREMENTS 9 1 Physical Dimension 150mm W x 86mm H x 160mm D 9 2 Connectors 18AWG wire Orange Orange 22AWG Blue 18AWG 14 Black Green 18AWG 16 Black COM Black COM 18 Black COM White Red 5VDC Red 22AWG 5Vsense Black M B 24PIN connector Pin Signal 18AWG wire range2. 2 5 2 Other Low Power System Reguirements To help meet the Blue Angel RAL UZ 78 US Presidential executive order 13221 future EPA requirements and other low Power system requirements it is recommended that the 5VSB standby supply should be as efficient as possible Standby efficiency is measured with the main outputs off PS_ON high state Standby efficiency should be greater than 50 with a minimum loading of 100mA at input 115Vac Pin lt 1W with a minimum loading of 50mA at input 230Vac 2 6 Remote on off control When the logic level PS ON is low the DC outputs are to be enabled When the logic level is high or open collector the DC outputs are to be disabled o O SS STRIDER SST ST6OF AWR 3 PROTECTION 3 1 Over power protection The power supply will be shutdown and latch off when output power is 110 150 3 2 Over voltage protection The over voltage sense circuitry and reference shall reside in packages that are separate and distinct from the regulator control circuity and reference No single point fault shall be able to cause a sustained over voltage condition on any or all outputs The supply shall provide latch mode over voltage protection as defined in Table woon e vos 5VDC 7 0 Volts 3 3VDC 4 8 Volts 3 3 Under voltage protection The under voltage sense circuitry and reference shall reside in packages that are separate and distinct from the regulator control circuity and reference No sin
3. Black 5VDC 5VDC OM Black OM O O range O range 5VDC 7 Black PWRGOOD Grey 18AWG Purple 10 12V1 Yellow Black stripe 11 12V1 Yellow Black stripe orange 2 2 2 1 2 2 23 NO i STRIDER SST ST60F AWN EPS 12V 8PIN connector 12V2 e co s12v1 7 3 Com Black 1 8 4 com Bak_ ATX 12V 4PIN AWG we Signal Pm Pn Sora Yellow 4PIN DON connector HDD 4PIN MA connector FDD BANG wire Signal Pn Pn Signal 22AWG wird CELTA O I E SS Black co 2 com Black aia com s 3 com Black UI vwo 4 4 Ni wem SATA connector IBANG wir 6PIN PCI Express connector 1 amp 2 amp 3 amp 4 IBANG wire Signal Pn Pm Signal 22AWG wir ae wv s 6 com Black 8PIN PCI Express connector ISANG wire Signal Pn Pin Signal 22AWG wis ave 1 5 com Black av 2 6 om Black sv a 7 oom Black CBlacksensev com 4 8 com Black gt 10 FAN SPEED CONTROL Fan voltage varies with the ambient temperature or output power STRIDER SST ST6OF To be valid this sheet muet be filled out Dy Store Purchaser Purchase date Model No Serial No SilverStone Technology Co Ltd www silverstonetek com support silverstonetek com Issue date January 2008 NO G11206080
4. 1 Maximum continuous total DC output power should not exceed 600W 2 Maximum continuous combined load on 3 3VDC and 5VDC outputs shall not exceed 170W 3 The maximum peak total DC output power shall not exceeed 620 watts 4 Peak power and current loading shall be supported for a minimum of 12 second 5 Maximum combined current for the 12V outputs shall be 48A 2 3 DC Output Ripple Noise 2 3 1 Ripple regulation Parameter Ripple Noise 3 3V 50 5V 12V1 120 12V2 120 158B 2 3 2 Definition The ripple voltage of the outputs shall be measured at the pins of the output connector when terminated in the load impedance specified in figure 1 Ripple and noise are measured at the connectors with a 0 1uF ceramic capacitor and a 10uF electrolytic capacitor to simulate system loading Ripple shall be measured under any condition of line voltage output load line frequency operation temperature 2 3 3 Ripple Noise voltage test circuit Power Supply AG Flot 10uF 0 1uF Vreturn Load AC Neutral ES AC Ground Figure 1 Ripple Noise voltage test circuit 2 4 Overshoot Any overshoot at turn on or turn off shall be less 10 of the nominal voltage value all outputs shall be within the regulation limit of section 2 0 before issuing the power good signal of section 4 0 2 5 Efficiency 2 5 1 Power supply typical efficiency is 80 min under 20 Load 50 Load 100 Load at nominal input voltage of 115VAC
5. SILVERSTONE Designing Inspiration STRIDER SERIES SST ST60F Elevated high affordability and great performance at ease Ultra silent running 135mm fan with 18dBA Efficiency 80 85 at 20 100 loading 600W continuous power output rated Dual 12V with continuous 48A combined output Quad PCI E 6pin single PCI E 8pin 100 modular cables SPECIFICATION SilverStone Strider SST ST60F ATX12V 2 3 Switching Power Supply With Active PFC PS 2 600W This specification describes the requirements of 600W with active P F C Switching Power Supply with an ATX form factor 5V standby voltage fan control ATX12V 2 3 EPS12V 2 91 Power supply version remote on off control full range input capability and forced air cooling characteristics 1 AC INPUT REQUIREMENTS The input voltage current and frequency requirements for continuous operation are stated below Vin Frequency 63 Hz lin A Power factor correction PF gt 0 95 at full load 1 1 Inrush current limiting 50A O 115Vrms 100A 2 230Vrms at 25 C ambient cold start 2 DC OUTPUT 2 1 DC voltage regulation Parameter Range Min Nom Max Unit 12V1 11 40 12 0 12 60 12V2 5 11 40 12 0 12 60 Volts 12V 10 10 80 12 0 13 2 Volts Sa STRIDER SST ST60F AWR 2 2 Load Ranges 2 2 1 Typical Power Distribution for 600W ATX12V Configuration Max 12V1DC Mn nom sao 09 3 3VDC 0 0 5 25 0 syss oo 250
6. all protect the power supply from damage or abnormal and or dangerous operation A shutdown of the power supply is acceptable A temperature derating factor less than 110 for the critical components is recommended before the power supply is shut down Temperature derating factors higher than 110 can be evaluated on a case by case basis 4 TIMING 4 1 Signal timing drawing Figure 4 is a reference for signal timing for main power connector signals and rails VAC PS ON 10 12V 5V 3 3V O P PW OK 1 i 1 1 PW OK Sense level 95 of i i 4 HTa nominal i Figure 2 PS OK Timing Sequence T2 Rise time 0 1ms 20ms T3 Power good turn on delay time 100ms 500ms T4 Power good turn off delay time 1ms min T5 Rise time 10ms max 1 2 3 4 4 2 Hold up time T6 of figure 2 When the power loss its input power the output shall maintain 16ms in regulation ranges at nominal input voltage AC 115V 60Hz or 230V 50Hz o al SS STRIDER SST ST6OF AWR 5 ENVIRONMENT 5 1 Operation 0 C to 40 C Relative Humidity 20 to 85 non condensing 5 2 Shipping and Storage 40 C to70 C Relative Humidity 5 to 90 non condensing 5 3 Altitude Operating 3 000FT max 6 SAFETY 6 1 Underwriters Laboratory UL recognition The power supply designed to meet UL 1950 6 2 The power supply must bear the German Bauart Mark from TUV 7 0 ELECTROMAGNETIC COMPATIBILITY EMC 7 1 ELECTROSTATIC DISCHARGE ESD
7. gle point fault shall be able to cause a sustained under voltage condition on any or all outputs The supply shall provide latch mode under voltage protection as defined in Table 5 VDC 4 1 4 3 4 47 Volts 3 3 VDC 2 55 2 69 2 83 Volts 3 4 Over Current Protection 5VDC 12V1DC 12V2DC and 3 3VDC have separate over current protection circuits to meet 240VA safety requirement 3 5 Short circuit An output short circuit is defined as any output impedance of less than 0 1 ohms The power supply shall shut down and latch off for shorting the 3 3VDC 5VDC or 12VDC rails to return or any other rail Shorts between main output rails and 5VSB shall not cause any damage to the power supply The power supply shall either shut down and latch off or fold back for shorting the negative rails 5VSB must be capable of being shorted indefinitely but when the short is removed the power supply shall recover automatically or by cycling PS_ON The power supply shall be capable of withstanding a continuous short circuit to the output without damage or overstress to the unit 2 3 6 No load operation No damage or hazardous condition should occur with all the DC output connectors disconnected from the load The power supply may latch into the shutdown state 3 7 Over temperature protection In the event of a fan failure or the vents being blocked the power supply shall have protection such that any over temperature condition caused by these events sh
Download Pdf Manuals
Related Search