Chief PWR2059S flat panel wall mount
Contents
1. HEIGHTADJUSTN ENT o TILT ROLL YAW S5 wp 1 E ON THE MOUNT 25 2 u 178 SEE PSB XXXX DRAWING ALSO 1 00 7 00 7 p o f 397 9 e 15 65 pui D M LS M 2 mm 64 2 51 406 16 00 ALL MEASUREMENTS IN THE FOLLOWING FORMAT MILLIMETERS INCHES UNIT DEPTH TILTAD USTMENT Extended Retracted 851 Tilted Up Tilted Down 3 36 5 pese b 2 SZ W gt olf JJ Figure 1 Installation Instructions Mount Installation WARNING IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT It is the installer s responsibility to make sure the structure to which the PWR is being installed is capable of supporting five times the combined weight of the mount and all attachments 1 Determine mounting location taking into consideration display size and mount movement 2 Using a stud sensor locate two wood studs 16 apart on center See Figure 2 3 Using two p2. in serious personal injury damage to equipment or voiding of factory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for the installation of this kit can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this mount is attached can support five times the combined weight of all equipment WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to this accessory does not exceed 125 lbs 56 7 kg Adjust Hex Head Wrench Phillips Screwdriver lt gt Installation Instructions PWR TOOLS REQUIRED FOR INSTALLATION AND PARTS E 10 _ 7 32 9 32 a 5 16 x 2 1 2 H 4 850x 385x 135 PWR DIMENSIONS NO TE CUSTO M INTERFACE BRACKET NOTSHOWN THE CUSTOM INTERFACE BRACKET NEEDED FOR YOUR DISPLAY WILL ADD BETWEEN 1 2 AND 2 IN DEPTH AND MAY AFFECTLOCATION OF DISPLAY Mounting Pattem Installation Instructions PRODUCTFEATUMES WEIGHT CAPAC ITY 125 18S
3. Cover Installation To install channel covers 1 Install upper and lower wall channel covers B by tipping cover top down and positioning as shown in end view of figure below See Figure 5 2 firmly across bottom of channels B to lock in place as shown in figure below See Figure 5 3 Install R H and L H end caps F by aligning tabs on end caps F with slots in wall channel covers B and sliding tabs in until end caps F are flush with wall channel covers B See Figure 5 END VIEW Figure 5 PWR Display Installation WARNING IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT Displays can weigh in excess of 40 Ibs 18 1kg ALWAYS use two people and proper lifting techniques when installing display WARNING IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT Make sure mounting buttons on display are properly seated in mounting holes in faceplate To install display 1 Move mount faceplate to extended position by grasping faceplate and pulling outward away from wall See Figure 6 2 While supporting both sides of display align four mounting buttons on display or interface bracket with fo
4. INSTALLATION INSTRUCTIONS Large Flat Panel Wall Mount CHIEF Qur Mounts Your Vision PWR DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions LEGEND Tighten Fastener Loosen Fastener Open Ended Wrench Installation Instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result
5. ables through holes in faceplate Installation Instructions From Display Figure 8 ADJUSTMENTS Pitch Tension Adjustment To adjust display pitch tension 1 With display installed tighten or loosen two screws one on each side using a 5 32 hex wrench See Figure 9 2 Check for desired tension 3 Repeat Steps 1 and 2 until desired tension is obtained PWR Figure 9 PWR Roll Adjustment The PWR allows for the horizontal alignment Roll of the display to be adjusted up to 2 right or left to level the display after installing To adjust Roll 1 Loosen the roll tension adjustment nut located on the back side of the faceplate assembly See Figure 10 2 Level display 3 Tighten roll tension adjustment nut See Figure 10 Figure 10 Swing Arm Tension Adjustment owing arm tension is pre set at the factory and is adjusted to accommodate displays with weights near the top of the mounts capacity If smaller displays are used it may be difficult to reposition the display after mounting Swing arm tension can be adjusted to compensate for smaller display by The display must be mounted prior to adjusting swing arm tension 1 Locate the adjustment bar H and adjustment wrench J 2 Place adjustment bar H into socket head cap screw located at swing arm pivot point See Figure 11 NOTE The
6. display may need to be repositioned in order to gain access to the tension adjustment screw s 3 Check swing arm tension If desired tension is present tension adjustment is complete If additional tension adjustment is required repeat steps 2 thru 4 until desired tension is achieved NOTE f changing from a smaller display to a larger display may be necessary to increase swing arm tension 10 Installation Instructions Socket Head Capscrew Figure 11 Using the adjustment wrench D turn adjustment bar C clockwise to increase swing arm tension or counterclockwise to reduce swing arm tension Small adjustments of 1 8 turn or less are typically all that is required to achieve desired tension See Figure 12 and See Figure 13 DECREASE Figure 12 4 INCREASE Figure 13 Installation Instructions PWR 11 PWR e CH E F USA International Our Mounts Your Vision Chief Manufacturing a products division of Milestone AV Technologies Asia Pacific 8831 000006 RevF 92010 Milestone AV Technologies a Duchossois Group Company www chiefmfg com 08 10 p TI gt Tl Installation Instructions 8401 Eagle Creek Parkway Savage MN 55378 800 582 6480 952 894 6280 877 894 6918 952 894 6918 Fellenoord 130 5611 ZB EINDHOVEN The Netherlands 31 0 40 2668620 31 0 40 2668615 Office No 1 on 12 F Shatin Galleria 18 24 Shan Mei Street Fotan Shati
7. eople place mount against wall and level mount aligning mounting holes in upper and lower wall channels with studs See Figure 2 4 Use a pencil mark four mounting holes making sure mounting holes are located as close as possible to center of studs See Figure 2 5 Drill four pilot holes where the mounting holes were marked using a 7 32 6mm drill bit See Figure 2 6 Install two 5 16 x 2 1 2 lag bolts G and two 0 135 thick washers H through mounting holes in upper wall channel and into pilot holes DO NOT tighten at this time 7 Using two people place mount against wall aligning mounting holes in upper wall channel with lag bolts and hang mount on lag bolts making sure washers are located in front of mount 8 Adjust mount lateral position left until lag bolts are seated in mounting slots in upper wall channel 9 Install two 5 16 x 2 1 2 lag bolts G and two 0 135 thick washers H through mounting holes in lower wall channel and into pilot holes See Figure 3 10 Tighten all hardware DO NOT overtighten Figure 3 7 32 x 4 Figure 2 PWR Mounting holes centered on studs PWR Installation Instructions Mount Lateral Position Adjustment The PWR is designed to allow up to 5 of right or left lateral adjustment after being mounted to the wall This lateral adjustment can be used to more precisely position where the center of
8. n Hong Kong 852 2145 4099 852 2145 4477 we as o ConsuMe
9. the display is located when installation is complete To adjust the mounts lateral position 1 Remove display if installed 2 While holding swing arm remove two hex head cap screws and two washers securing swing arm to upper wall channel See Figure 4 3 While holding swing arm remove two hex head cap screws and two washers securing swing arm to lower wall channel 4 Sethardware aside for reuse See Figure 4 5 Slide swing arm left or right until desired location is reached making sure mounting holes in swing arm upper and lower mounting plates align with mounting slots in upper and lower wall plates See Figure 4 6 Secure swing arm to upper and lower wall channels using hex head cap screws and washers set aside during steps 1 and 2 See Figure 4 ADE Hex Head Cap Screw and Washer Upper Swing Arm Mounting Plate Upper Wall Channel Lower Wall Channel Lower Swing Arm Mounting Plate Hex Head Cap Screw and Washer ADE ce e Figure 4 Installation Instructions PWR
10. ur mounting holes in faceplate See Figure 6 3 Lower display into place listening for audible click to ensure recessed area of mounting buttons are properly seated in lower area of mounting holes and click lock mechanism has engaged See Figure 6 and See Figure 7 Figure 6 NOTE Holes are provided in the faceplate for use with a padlock or similar locking device if desired In addition the pin and nut may be removed from the upper holes and moved to the lower holes for use as a more permanent locking device See Figure 7 Installation Instructions N Remove pin and nuts and move to lower holes A padlock or bolt may be placed through latch holes Figure 7 CABLE MANAGEMENT WARNING IMPROPER INSTALLATION CAN LEAD TO SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Make sure cables do not run through pinch points Loosen front and rear cable clamps on top arm See Figure 8 Thread cable ties E under cable clamps and secure clamps to top arm See Figure 8 Route power audio video cables through the cable channel in top arm See Figure 8 allowing sufficient slack in cables for Left Right movement of display and swing arm and also swing arm extension and retraction Secure cables to top arm using two cable ties E Repeat steps 1 through 4 for lower arm WARNING IMPROPER INSTALLATION CAN LEAD TO SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT DO NOT route c
Download Pdf Manuals
Related Search