Toshiba IK-DP30A surveillance camera
Contents
1. Position the cursor next to SCAN LIMIT STOPS and press the OPEN button to move the cursor to the right Move the joystick up or down to select ON or OFF To accept the selection press the OPEN button or to cancel the selection press the CLOSE button To set SCAN LIMIT STOPS 1 2 3 4 5 Set SCAN LIMIT STOPS to ON and exit menu Position the camera for the LEFT LIMIT STOP Enter 92 preset SCAN LEFT LIMIT will be displayed on screen Position the camera for the RIGHT LIMIT STOP If the right limit stop is less than 10 degrees from the left limit stop NOT ACCEPT will be displayed on screen Enter 93 preset SCAN RIGHT LIMIT will be displayed on screen 6 8 4 MANUAL LIMIT STOPS When a Manual Limit Stop is reached during a manual joystick pan the camera will stop A Left Manual Limit Stop and Right Manual Limit Stop can be set The limit stops must be greater than 10 degrees apart Menu MAIN MENU CAMERA SETUP D PAN TILT SETUP PRESET TITLES OTHERS PAN TILT MENU AUTO FLIP ON PROPORTIONALP T ON SCAN LIMIT STOPS OFFI gt MANUAL LIMIT STOPS OFF PARK TIME MIN OMIN AUTO PATROL P1 0OFF EXIT SCAN SPEED 5DEG S SCAN TILT ANGLE 30DEG STOP TIME 10SEC MAX SPEED 400DEG S To enable MANUAL LIMIT STOPS 1 2 A Enter the preset command to access the main menu Refer to section 6 1 for the controller model and preset command Position the cursor next to P2. SENSITIVITY NORMAL LOW NORMAL WHITE BALANCE AUTO ATW ONE PUSH WB ATW AUTO EXPOSURE MODE FULL AUTO SHUTTER PRIORITY FULL AUTO AUTO SLOW SHUTTER ON OFF OFF SHUTTER SPEED 1 1 1 10000 22 step 1 60 AE COMPENSATION o BACK LIGHT COMP ON OFF OFF DAY NIGHT AUTO MANUAL AUTO ZOOM LIMIT x18 36 72 144 216 x18 SHARPNESS 07 15 10 LINE LOCK MODE ON OFF OFF LINE PHASE 40 250 180 PRIVACY ZONE P1 P8 P1 OFF PAN TILT SETUP AUTO FLIP ON OFF ON PROPORTIONAL P T ON OFF ON SCAN LIMIT STOPS ON OFF MANUAL LIMITS STOPS ON OFF PARK TIME MINUTES 0 720MIN AUTO PATROL PRESET1 ON OFF PRESET2 ON OFF PRESET66 ON OFF ALL OFF SCAN SPEED 1 90 DEGREE S 5 SCAN TILT ANGLE 0 92 DEGREE 30 STOP TIME 1 60 SEC 10 MAX SPEED 30 400 DEGREE S 400 PRESET TITLES TITLE INPUT It is to 20 characters to each Preset number Blank TITLE POSITION UP DOWN DOWN OTHERS POWER UP DEFAULT PARK AUTO SCAN FRAME SCAN RANDOM SCAN AUTO PATROL PARK FREEZE ACTIVITY ON OFF LOAD FACTORY DEFAULT TILT ANGLE 80 INDOOR OUTDOOR 8 Switch Setting There are three switches which must be set up Switch
3. 6 8 PAN TILT SETUP 6 8 1 AUTO FLIP The Auto Flip feature allows the tilt to rotate 180 degrees and reposition itself for continuous viewing of a moving object directly beneath the dome Menu MAIN MENU PAN TILT MENU gt AUTO FLIP ON CAMERA SETUP PROPORTIONALP T ON SCAN LIMIT STOPS OFF PAN TILT SETUP gt MANUAL LIMIT STOPS OFF PARK TIME MIN OMIN AUTO PATROL P1 OFF lt OTHERS gt EXIT SCAN SPEED 5DEG S SCAN TILT ANGLE 30DEG STOPTIME 10SEC MAX SPEED 400DEG S To enable AUTO FLIP 1 Enter the preset command to access the main menu Refer to section 6 1 for the controller model and preset command 2 Position the cursor next to PAN TILT SETUP and press the OPEN button to access the Pan Tilt menu 3 Position the cursor next to AUTO FLIP and press the OPEN button to move the cursor to the right 4 Move the joystick up or down to select ON or OFF 5 To accept the selection press the OPEN button or to cancel the selection press the CLOSE button 18 6 8 2 PROPORTIONAL P T Proportional P T controls the pan and tilt speeds according to the amount of zoom At telephoto settings the pan and tilt speeds will be slower to keep the image from moving too fast on the monitor Menu MAIN MENU PAN TILT MENU AUTO FLIP ON CAMERA SETUP gt PROPORTIONALP T SCAN LIMIT STOPS OFF PAN TILT SETUP MANUAL LIMIT STOPS OFF PARK TIME MIN OMIN AUTO PATROL P1 OFF lt OTHERS gt
4. EXIT SCAN SPEED 5DEG S SCANTILT ANGLE 30DEG STOPTIME 10SEC MAX SPEED 4000 0 8 To enable PROPORTIONAL P T 1 Enter the preset command to access the main menu Refer to section 6 1 for the controller model and preset command 2 Position the cursor gt next to PAN TILT SETUP and press the OPEN button to access the Pan Tilt menu 3 Position the cursor next to PROPORTIONAL P T and press the OPEN button to move the cursor to the right 4 Move the joystick up or down to select ON or OFF 5 To accept the selection press the OPEN button or to cancel the selection press the CLOSE button 6 8 3 SCAN LIMIT STOPS When a Scan Limit Stop is reached during random frame or auto scan the dome camera will reverse direction A Left Scan Limit Stop and Right Scan Limit Stop can be set The limit stops must be greater than 10 degrees apart Menu MAIN MENU PAN TIL MENU AUTO FLIP ON lt CAMERA SETUP gt PROPORTIONALP T ON gt PAN TILT SETUP gt SCAN LIMIT STOPS OFF lt PRESET TITLES MANUAL LIMIT STOPS OFF PARKTIME MIN OMIN OTHERS AUTO PATROL P1 OFF EXIT SCANSPEED 5DEGJS SCANTILT ANGLE 30DEG STOPTIME 10SEC MAX SPEED 400DEG S 19 To enable SCAN LIMIT STOPS 1 2 A Enter the preset command to access the main menu Refer to section 6 1 for the controller model and preset command Position the cursor gt next to PAN TILT SETUP and press the OPEN button to access the Pan Tilt menu
5. Position the cursor next to STOP TIME and press the OPEN button to move the cursor to the right Move the joystick up or down to set the stop time To accept the selection press the OPEN button or to cancel the selection press the CLOSE button 6 8 10 MAX SPEED The maximum speed of Pan Tilt functions can be set from 30 degrees sec to 400 degrees sec The max speed controls global Pan Tilt speeds To reduce rotation noise use a lower speed Menu MAIN MENU PAN TILT MENU AUTO FLIP ON CAMERA SETUP PROPORTIONALP T ON SCAN LIMIT STOPS OFF PAN TILT SETUP gt S eig MANUAL LIMIT STOPS OFF PARKTIME MIN OMIN OTHERS AUTO PATROL P1 OFF EXIT SCANSPEED 5DEGJS SCANTILT ANGLE 30DEG STOPTIME 10SEC D MAXSPEED 400DEG S To set MAX SPEED 1 2 Enter the preset command to access the main menu Refer to section 6 1 for the controller model and preset command Position the cursor next to PAN TILT SETUP and press the OPEN button to access the Pan Tilt menu Position the cursor next to MAX SPEED and press the OPEN button to move the cursor to the right Move the joystick up or down to set the maximum speed To accept the selection press the OPEN button or to cancel the selection press the CLOSE button 24 6 9 PRESET TITLES SETUP Titles can be set for up to 64 presets pan tilt position and zoom Titles can be up to 20 characters in length and can be displayed at the top or bot
6. Remote Control VF RS 422 receive only Protocol Toshiba P D Dip sw selectable Data rate 1200 2400 4800 9600bps Dip sw selectable 38 LIMITED WARRANTY CCD SECURITY DOME CAMERA IK DP30A The Imaging System Division ISD of Toshiba America Information Systems Inc makes the following limited warranties with regard to this CCD Camera model IK DP30A Product These limited warranties extend to the Original End User You r Three 3 Year Limited Warranty of Labor and Parts ISD warrants that this Product will perform in accordance with specifications for a period of three 3 years from the date of purchase by the Original End User During this three 3 year period ISD will repair or replace the Product if it does not perform as warranted In order to take advantage of this Limited Warranty You must a call 877 855 1349 to receive a RMA number and b pay all transportation and insurance charges for shipment of the Product to the ASP or Toshiba Exchange Center ISD reserves the right to substitute factory refurbished parts in place of those in need of repair Instruction Manual Owner s Manual You should read the Instruction Manual Owner s Manual thoroughly before operating this Product Before seeking warranty service you should check the troubleshooting guide in the Instruction Manual Owner s Manual and follow the instructions to correct the problem How to Obtain Warranty Servic
7. NOT APPLY TO YOU IF THIS PRODUCT IS NOT IN GOOD WORKING ORDER AS WARRANTED ABOVE YOUR SOLE AND EXCLUSIVE REMEDY SHALL BE THE REPAIR OF REPLACEMENT OF THE PRODUCT IN NO EVENT WILL ISD OR ITS PARENT COMPANY OR ANY ASP BE LIABLE TO YOU OR ANY THIRD PARTY FOR ANY DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT THIS LIMITATION APPLIES TO DAMAGES OF ANY KIND INCLUDING ANY DIRECT OR INDIRECT DAMAGES LOST PROFITS LOST SAVINGS OR OTHER SPECIAL INCIDENTAL EXEMPLARY OR CONSEQUENTIAL DAMAGES WHETHER FOR BREACH OF CONTRACT TORT OR OTHERWISE OR WHETHER ARISING OUT OF THE USE OF OR INABILITY TO USE SUCH PRODUCT EVEN IF TAIS ITS PARENT COMPANY OR AN ASP HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR OF ANY CLAIM BY ANY OTHER PARTY SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR SOME PRODUCTS SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE THIS LIMITED WARRANTY SHALL BE VOID IF THE PRODUCT OR PARTS HAVE BEEN SUBJECTED TO MISUSE ABUSE ACCIDENT IMPROPER INSTALLATION IMPROPER MAINTENANCE OR USE IN VIOLATION OF ISD S WRITTEN INSTRUCTIONS OR WHERE THE PRODUCT HAS BEEN ALTERED OR MODIFIED WITHOUT ISD S PRIOR AUTHORIZATION OR UPON THE REMOVAL OR ALTERATION OF ISD S FACTORY SERIAL NUMBER LABOR SERVICE CHARGES FOR PRODUCT INSTALLATION SET UP AND ADJUSTMENT OF CO
8. PRIVACY ZONE Privacy Masking ON OFF A maximum of 8 zones can be set 1 2 Enter the preset command to access the main menu Refer to section 6 1 for the controller model and preset command Position the cursor next to CAMERA SETUP and press the OPEN button to access the menu Position the cursor next to PRIVACY ZONE and press the OPEN button to move the cursor to the right Move the joystick up or down to set P1 to P8 ON OFF separately To accept the selection press the OPEN button or to cancel the selection press the CLOSE button Privacy zone setup 1 Use a joystick to move where you want to set a privacy zone 2 Enter 83 preset to access the setup screen Displays PRIVACY ZONE gt 1 1 the number indicates zone 8 zone can be set Press the OPEN button to set ZONE SIZE Use a joystick to create the privacy zone to mask Press the OPEN button to set ZONE COLOR Use joystick to select the MASK COLOR to either Black Gray Press the CLOSE button 47 Notes 1 Masking areas are only rectangles 2 When using the PTZ function the privacy zone expands 2x vertically and 4x horizontally 3 Although the privacy zone works in digital zoom the zone setting is only available in a non digital zoom area 4 It is recommended to set privacy zone bigger than actual masking area 5 During turbo panning or tilting the privacy zone may shift depending on the location of the zone
9. The dome camera performs an auto patrol operation DEFAULT The dome camera moves to the mechanical reset point Menu MAIN MENU OTHERS MENU CAMERA SETUP D POWER UP PARK PAN TILT SETUP FREEZE ACTIVITY ON PRESET TITLES LOAD FACTORY DEFAULT D OTHERS TILT ANGLE OUTDOOR EXIT To set POWER UP MODE 1 2 3 A Enter the preset command to access the main menu Refer to section 6 1 for the controller model and preset command Position the cursor gt next to OTHERS and press the OPEN button to access the menu Position the cursor next to POWER UP and press the OPEN button to move the cursor to the right Move the joystick up or down to set the power up mode To accept the selection press the OPEN button or to cancel the selection press the CLOSE button 26 6 10 2 FREEZE ACTIVITY During frame scan random scan or auto patrol camera images will not be shown while the dome camera moves from the current position to the next position Menu MAIN MENU lt CAMERA SETUP gt lt PAN TILT SETUP gt lt PRESET TITLES gt gt lt OTHERS gt EXIT To set STOP TIME 1 Enter the preset command to access the main menu OTHERS MENU POWER UP PARK gt FREEZE ACTIVITY ON LOAD FACTORY DEFAULT TILT ANGLE OUTDOOR Refer to section 6 1 for the controller model and preset command 2 Position the cursor next to OTHERS and press the OPEN button to access the menu 3 Position t
10. 1 sets the camera address Switch 2 sets the protocol and bit rate Switch 301 sets the termination only used on the last daisy chained camera Dip switch SW1 amp SW2 It is necessary to set a unique camera address and protocol Set up a camera address according the following table 31 1 SWI Camera Address 32 2 3 Camera Address 1 x bit 1 Status 2 x bit 2 Status 4 x bit 3 Status 8 x bit 4 Status 16 x bit 5 Status 32 x bit 6 Status 64 x bit 7 Status 128 x bit 8 Status bit Status 1 Off 0 ex Camera Address 228 1 x 0 Off 2 x 0 Off 4 1 On 8 x 0 Off 16 x0 Off 32 x 1 On 64 x 1 On 128 x 1 On 4 32 64 128 228 Off Off On Off Off On On On Set up the protocol and bit rate to match the controllers settings SW2 bit 1 2 Protocol Protocol TOSHIBA P TOSHIBA D Reserve1 Reserve2 SW bit3 4 Bit Rate Dome base switch S301 This is RS422 termination switch located near the BNC connector In daisy chain operation system the farthest dome from the controller is turned ON For example when the controller is connected with three dome cameras in the direct mode the only furthest dome camera from a controller is
11. AN TILT SETUP and press the OPEN button to access the Pan Tilt menu Position the cursor next to MANUAL LIMIT STOPS and press the OPEN button to move the cursor to the right Move the joystick up or down to select ON or OFF To accept the selection press the OPEN button or to cancel the selection press the CLOSE button To set MANUAL LIMIT STOPS 1 2 3 Set MANUAL LIMIT STOPS to ON and exit menu Position the camera for the LEFT LIMIT STOP Enter 90 preset MANUAL LEFT LIMIT will be displayed on screen 20 4 Position the camera for the RIGHT LIMIT STOP If the right limit stop is less than 10 degrees from the left limit stop NOT ACCEPT will be displayed on screen 5 Enter 91 preset MANUAL RIGHT LIMIT will be displayed on screen 6 8 5 PARK TIME MINUTES After a programmed number of minutes of inactivity the dome camera will park to preset 1 The Park Time Minutes can be set from 1 to 720 minutes Setting it to 0 will disable the feature Menu MAIN MENU lt CAMERA SETUP gt D PAN TILT SETUP gt PAN TILT MENU AUTO FLIP ON PROPORTIONALP T ON SCAN LIMIT STOPS OFF MANUAL LIMIT STOPS OFF SPRESET gt MIN OMIN AUTO PATROL P1 OFF lt OTHERS gt EXIT SCANSPEED 5DEGJS SCANTILT ANGLE 30DEG STOPTIME 10SEC MAX SPEED 400DEG S To set PARK TIME MIN 1 Enter the preset command to access the main menu Refer to section 6 1 for the controller model and prese
12. E LOCK CONTROL The dome camera can be synchronized with the power supply frequency Menu Line Lock can be set to ON or OFF The Line Lock Phase can be set from 40 to 250 degrees MAIN MENU D CAMERA SETUP PAN TILT SETUP PRESET TITLES OTHERS EXIT CAMERA MENU LINE LOCK FOCUS WB ATW AE ZOOM LIMIT SHARPNESS MODE LINE PHASE OFF 180 X18 10 gt lt LINE LOCK gt PRIVACY ZONE 16 To change the LINE LOCK options 1 2 3 Enter the preset command to access the main menu Refer to section 6 1 for the controller model and preset command Position the cursor next to CAMERA SETUP and press the OPEN button to access the Camera menu Position the cursor next to LINE LOCK and press the OPEN button to access the Line Lock menu Position the cursor next to the desired option and press the OPEN button to move the cursor to the right Move the joystick up or down to select the option setting To accept the selection press the OPEN button or to cancel the selection press the CLOSE button 6 7 7 PRIVACY ZONE MASKING This function masks a user defined area that cannot be viewed by the operator The mask adjusts with the pan tilt and zoom of the camera Menu MAIN MENU gt CAMERA SETUP gt PAN TILT SETUP PRESET TITLES CAMERA MENU FOCUS WB ATW AE OTHERS EXIT ZOOM LIMIT X18 SHARPNESS 10 lt LINE LOCK gt gt
13. EN button to access the menu 3 Position the cursor next to TILT ANGLE and press the OPEN button to move the cursor to the right Move the joystick up or down to set the tilt angle mode 5 To accept the selection press the OPEN button or to cancel the selection press the CLOSE button A 28 7 Menu Directory TOP MENU gt CAMERA SETUP PAN TILT SETUP PRESET TITLES OTHERS EXIT CAMERA SETUP MENU D FOCUS WB ATW AE ZOOM LIMIT X18 SHARPNESS 10 LINE LOCK gt PRIVACY ZONE 1 gt PAN TILT SETUP MENU gt AUTO FLIP ON PROPORTIONALP T ON SCAN LIMIT STOPS OFF MANUAL LIMIT STOPS OFF PARK TIME MIN OMIN AUTO PATROL P1 OFF SCAN SPEED 5DEG S SCAN TILT ANGLE 30DEG STOP TIME 10SEC MAX SPEED 400DEG S PRESET TITLES MENU gt TITLE INPUT TITLE POSITION DOWN OTHERS MENU gt POWER UP PARK FREEZE ACTIVITY OFF LOAD FACTORY DEFAULT TILT ANGLE OUTDOOR 29 FOCUS SETUP MENU gt MODE AUTO ACTIVE TIME 5S INTERVAL TIME 5S SENSITIVITY NORMAL AE MENU gt MODE FULL AUTO AUTO SLOW SHUTTER OFF SHUTTER SPEED 1 60 AE COMPENSATION 0 BACK LIGHT COMP OFF DAY NIGHT AUTO LINE LOCK MENU gt MODE OFF LINE PHASE 180 7 1 MENU LIST AND SETTINGS Sub Menu 1 Sub Menu 2 Contents Default MODE AUTO MANUAL ZOOM TRIGGER INTERVAL AUTO ACTIVE TIME 17 2558 55 INTERVAL TIME 1 255S 5S
14. NTROLS ARE NOT COVERED BY THIS LIMITED WARRANTY No person agent distributor dealer authorized service provider or company is authorized to change modify or extend the terms of this Limited Warranty in any manner whatsoever The time within which an action must be commenced to enforce any obligation of ISD arising under this Limited Warranty or under any statute or law of the United States or any state thereof is herby limited to one 1 year from the date You discovered or should have discovered the problem This limitation does not apply to implied warranties arising under state law Some states do not permit limitation of the time within which You may bring an action beyond the limits provided by state law so the above provision may not apply to You This Limited Warranty gives You specific legal rights and You may also have other rights which vary from state to state TOSHIBA AMERICA INFORMATION SYSTEMS INC Imaging Systems Division T 5 B A V2 0
15. PRESET Color mode 89 PRESET monochrome mode Aninfrared IR Cut Filter can be disengaged from the image path for increased sensitivity in low light environments This function will automatically engage depending on the ambient light allowing the camera to be effective in DAY NIGHT environments 14 Note At the time of SHUTTER PRIORITY mode choice DAY NIGHT mode is fixed in MANUAL To change the AE options 1 Enter the preset command to access the main menu Refer to section 6 1 for the controller model and preset command 2 Position the cursor gt next to CAMERA SETUP and press the OPEN button to access the Camera menu 3 Position the cursor next to AE and press the OPEN button to access the AE menu 4 Position the cursor next to the desired option and press the OPEN button to move the cursor to the right Move the joystick up or down to select option setting 6 To accept the selection press the OPEN button or to cancel the selection press the CLOSE button oa 6 7 4 ZOOM CONTROL Direct The zoom feature has 4 varying speeds The zoom feature can be controlled directly for Wide angle or Telephoto angle Menu MAIN MENU CAMERA MENU gt lt SETUP FOCUS PAN TILT SETUP WB ATW PRESET TITLES AE OTHERS gt ZOOM LIMIT X18 EXIT SHARPNESS 10 LINE LOCK gt PRIVACY ZONE A zoom limit can be set to x18 x36 x72 x144 and x216 The maximum op
16. S OFF PARK TIME MIN OMIN AUTO PATROL P1 OFF EXIT SCAN SPEED 5DEG S gt SCANTILT ANGLE 30DEG STOPTIME 10SEC MAX SPEED 400DEG S To set SCAN TILT ANGLE 1 Enter the preset command to access the main menu Refer to section 6 1 for the controller model and preset command 2 Position the cursor gt next to PAN TILT SETUP and press the OPEN button to access the Pan Tilt menu 3 Position the cursor next to SCAN TILT ANGLE and press the OPEN button to move the cursor to the right 4 Move the joystick up or down to set the tilt angle 5 To accept the selection press the OPEN button or to cancel the selection press the CLOSE button 6 8 9 STOP TIME During frame scan random scan or auto patrol a stop time from 1 sec to 60 sec can be set During scanning the camera will not move for the specified time at each stop Menu MAIN MENU lt CAMERA SETUP gt gt PAN TILT SETUP gt PRESET TITLES OTHERS EXIT PAN TILT MENU AUTO FLIP ON PROPORTIONALP T ON SCAN LIMIT STOPS OFF MANUAL LIMIT STOPS OFF PARK TIME MIN OMIN AUTO PATROL 1 gt gt SCAN SPEED 5DEG S SCAN TILT ANGLE 30DEG gt STOP TIME 10SEC MAX SPEED 4000 5 To set STOP TIME 1 2 A Enter the preset command to access the main menu Refer to section 6 1 for the controller model and preset command Position the cursor next to PAN TILT SETUP and press the OPEN button to access the Pan Tilt menu
17. TO S H INSTRUCTION MANUAL ZEIM 4000008G A 1 DOME CAMERA IK DP30A Please read this manual thoroughly before use and keep it handy for future reference Record in space provided below the Model No and the Serial Number as found on the label on the bottom of the camera Model No IK DP30A Serial No Retain this information for future reference TABLE OF CONTENTS IMPORTANT SAFEGUARDS see 2 1 Features and description 4 25 CAUTIONS T 4 3 Components sse nennen 4 4 Part names and Locations 5 5 COnNeECtiONS Apoena haenar entren 6 Operations ce aa 7 7 Menu Directory 29 8 Switch Setting 31 9 Installation 34 10 9 ict ete eet Ped 37 IMPORTANT SAFEGUARDS 1 Read Instructions All the safety and operating instructions should be read before the product is operated 2 Retain Instructions The safety instructions and instruction manual should be retained for future reference 3 Heed Warnings Comply with all warnings on the product and in the instruction manual 4 Follow Instructions Follow all operating and use instructions 5 Cleaning Disconnect this video product from the power
18. a will pan continuously between scan limit stops until a manual pan tilt or zoom operation is performed from the keyboard To set scan limit stops refer to SCAN LIMIT STOPS under PAN TILT SETUP in the camera menu Zoom At power up the zoom is fully Zoomed out When an auto scan is started directly from the keyboard the zoom will maintain the last magnification Tilt At power up the tilt is set up by the menu To set the tilt angle refer to SCAN TILT ANGLE under PAN TILT SETUP When an auto scan is started directly from the keyboard the tilt will maintain the last tilt angle FRAME SCAN The dome camera can perform a frame scan operation during power up and by direct control from the keyboard Operation of zoom and tilt is the same as in Auto Scan Scan limit stops ARE NOT set The dome camera will move in 45 degree increments called stops horizontally until a manual pan tilt or zoom operation is performed from the keyboard See figure below stop stop Scan limit stops ARE set The dome camera will move in 45 degree increments horizontally within the limit stops until a manual pan tilt or zoom operation is performed from the keyboard See figure below Right Limit Left Limit 10 RANDOM SCAN The dome camera can perform a random scan operation during power up and by direct control from the keyboard Operation of zoom and tilt is the same as in Auto Scan Scan limit stops ARE NOT set T
19. at his own expense USER INSTALLER CAUTION Your authority to operate this FCC verified equipment could be voided if you make changes or modifications not expressly approved by the party 1 Features and description Quick Install Design Cuts Installation Time in Half 480 Lines Horizontal Resolution 400 Degree Second Pan 18X Optical 12X Digital Zoom Privacy Zone Masking 0 01 Lux Minimum Illumination 1 4 IR Cut filter Off 50dB Signal To Noise Ratio 64 Position Preset Auto Flip Proportional Zoom 2 Cautions 1 In order to protect the camera avoid placing or using it under direct sunlight rain or dust 2 Avoid touching the zoom lens with your fingers If necessary use a soft cloth moistened with alcohol to wipe off any dust 3 When the camera is not in use keep the lens cap attached to protect the zoom lens 4 Avoid aiming the camera at the sun 5 Intense light such as a spotlight may cause a bloom or smear A vertical stripe may appear on the screen However this is not a malfunction 6 Install the camera away from video noise If cables are wired near electric lighting wires or a TV set noise may appear in images In this event relocate cables or reinstall equipment 3 Components 1 Dome base 2 Dome drive 3 Accessories Instruction manual 1 Install screw 3PCS 1 4 Part
20. at plugs screws and the point where they exit the product 12 Installation Install this video product on a firm and solid part of the ceiling or wall If installed on a weak place the camera could fall causing injury and damage 1 13 Lightning For additional protection on this video product during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the power supply and cable system This will prevent damage to the video product due to lightning and power line surges If lightning occurs do not touch the unit or any connected cables in order to avoid electric shock 14 Overloading Do not overload the power supply or extension cords as this can result in a risk of fire or electric shock 15 Object and Liquid Entry Never push objects of any kind into this video product through openings as they may touch dangerous electrical points or short out parts that could result in a fire or electrical shock Never spill liquid of kind on the video product 16 Servicing Do not attempt to service this video product yourself as opening or removing covers may expose you to dangerous electricity or other hazards Refer all servicing to qualified service personnel 17 Damage Requiring service Disconnect this video product from the power supply and refer servicing to qualified service personnel under the following conditions a When the power supply cord or plug i
21. e Step by step Procedures To obtain warranty service You should 1 Contact Toshiba at 877 855 1349 to first verify operation or installation assistance 877 855 1FIX 2 If technical support determines that the unit is defective an RMA will be issued with return instructions for repair 3 Securely pack the Product in the original carton and external shipping pack include a letter explaining the problem with a copy of the bill of sale or proof of purchase 4 Prepay all transportation and insurance costs Your Responsibilities This Limited Warranty is subject to the following conditions 1 You must provide the bill of sale or proof of purchase at the time that warranty service is required 2 You must notify 877 855 1349 within 30 days after you discover that the product does not perform in accordance with specifications during the Limited Warranty period 3 You must pack the Product in its original carton using the original packing material Then insert the original carton containing the Product into another carton with additional packing material before shipping the Product to an ASP or Toshiba Exchange Center DISCLAIMERS ALL OTHER EXPRESS OR IMPLIED WARRANTIES ON THIS PRODUCT INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS SO THE ABOVE LIMITATIONS MAY
22. e housing from the hole on the topside 9 Insertthe camera housing into the ceiling Push out the support arms so that they hold onto the ceiling Fig 3 Fig 3 10 Tighten the two support arm screws to secure the camera housing to the ceiling Fig 4 Fig 4 35 IK DP30A dome base install 11 Attach the video cable included with the dome accessories to the video connector of a dome base Note Do not connect a thick coaxial cable to a dome camera There is a possibility of damaging a connector Be sure to use the cable included in the dome accessories 12 Communication cables are directly inserted in the terminal of the dome base 13 Tighten the screw to secure the dome base to the housing Fig 5 O IK DP30A dome drive install 14 After setting up DIP SW in the top of the dome See 8 Switch setting connect the support wire to the hook of the dome base Fig 6 1 15 To lock the dome drive to the dome base line up the notch with the label and turn to the right with both hands Fig 6 Ensure that the location of the notch position of yellow paint on the dome base and the location of the installation label on the dome drive are aligned Fig 6 JK H01A dome cover install 16 To lock the dome cover insert the support wire and turn to the right with both hands Fig 7 Fig 8 Fig 8 17 The installation is complete 36 10 Specifications Overall Tempe
23. er can be varied from 1 sec 1 10000 in 22 steps The camera will automatically adjust the iris according to the level If the shutter speed is set to 1 1 or 1 2 sec the iris must be controlled manually AUTO SLOW SHUTTER In the FULL AUTO mode the AUTO SLOW SHUTTER feature can be set to ON or OFF A camera will automatically set the shutter slower than 1 60 sec according to the level of brightness Note In the SHUTTER PRIORITY mode the AUTO SLOW SHUTTER cannot be set SHUTTER SPEED Inthe SHUTTER PRIORITY mode the shutter can be varied from 1 sec 1 10000 in 22 steps The camera will automatically adjust the iris according to the level The iris cannot be controlled automatically if the shutter speed is set to 1 1 or 1 2 sec The iris must be controlled manually Note In the FULL AUTO mode SHUTTER SPEED cannot be set AE COMPENSATION AE COMPENSATION can be set from 7 to 7 As the numerical value becomes larger the Screen becomes brighter BACK LIGHT COMP Inthe FULL AUTO mode the BACK LIGHT COMPENSATION feature can be set to ON or OFF BACK LIGHT COMPENSATION can be set directly using JK UC1 Controller 71 PRESET ON 72 PRESET OFF Note In the SHUTTER PRIORITY mode the BACK LIGHT COMPENSATION feature cannot be set Day Night In the FULL AUTO mode the DAY NIGHT feature can be set AUTO or MANUAL MANUAL mode can be set directly using a JK UC1 Controller 88
24. he cursor next to FREEZE ACTIVITY and press the OPEN button to move the cursor to the right 4 Move the joystick up or down to set freeze activity to ON or OFF 5 To accept the selection press the OPEN button or to cancel the selection press the CLOSE button 6 10 3 LOAD FACTORY DEFAULTS The factory default settings can be loaded Menu MAIN MENU lt CAMERA SETUP gt lt PAN TILT SETUP gt lt PRESET TITLES gt D OTHERS EXIT To set LOAD FACTORY DEFAULT 1 Enter the preset command to access the main menu OTHERS MENU POWER UP PARK FREEZE ACTIVITY ON D LOAD FACTORY DEFAULT TILT ANGLE OUTDOOR Refer to section 6 1 for the controller model and preset command 2 Position the cursor next to OTHERS and press the OPEN button to access the menu 3 Position the cursor next to LOAD FACTORY DEFAULT and press the OPEN button twice to load factory default settings 6 10 4 TILT ANGLE Set up the Tilt angle according to the housing used and the purpose Indoor 85 degrees MAX Outdoor 92 degrees MAX Menu MAIN MENU OTHERS MENU lt CAMERA SETUP gt POWER UP PARK lt PAN TILT SETUP gt FREEZE ACTIVITY ON lt PRESET TITLES gt LOAD FACTORY DEFAULT gt lt OTHERS gt gt TILT ANGLE OUTDOOR EXIT To set TILT ANGLE 1 Enter the preset command to access the main menu Refer to section 6 1 for the controller model and preset command 2 Position the cursor gt next to OTHERS and press the OP
25. he dome camera will move between random stops and random tilt angles until a manual pan tilt or zoom operation is performed from the keyboard See figure below E stop 45 C stop stop G stop A A C H E G B D Scan limit stops ARE set The dome camera will move between random stops and random tilt angles within the limit stops until a manual pan tilt or zoom operation is performed from the keyboard See figure below stop stop Right Limit Left Limit stop ex A D B D 11 6 7 CAMERA SETUP 6 7 1 FOCUS CONTROL Direct The focus can be controlled directly using near or far focusing controls The focus control has 4 varying speeds One Push Trigger Auto Focus Menu MAIN MENU CAMERA MENU FOCUS MENU D CAMERA SETUP gt lt FOCUS gt MODE AUTO lt PAN TILT SETUP gt WB ATW ACTIVE TIME 5S lt PRESET TITLES gt lt AE gt INTERVAL TIME 5S lt OTHERS gt ZOOM LIMIT X18 SENSITIVITY NORMAL EXIT SHARPNESS 10 lt LINE LOCK gt PRIVACY ZONE The Focus control has four options Manual Auto Interval Zoom Trigger In the manual mode the IK DP30A focus is directly controlled with the near and far controls When the camera is in Auto Mode pressing the near and far controls will place the camera in manual mode until there is a zoom or pan tilt function In Interval mode the camera will switch between auto focus and manual focus according to the Active Time and Interval Time respectivel
26. he preset ON or OFF To accept the selection press the OPEN button or to cancel the selection press the CLOSE button 6 8 7 SCAN SPEED The SCAN SPEED for auto scan random scan and frame scan can be set from 1 90 degrees sec However this speed is limited by MAX SPEED setting Menu MAIN MENU PAN TILT MENU AUTO FLIP ON CAMERA SETUP gt PROPORTIONALP T ON EXPAND MANUAL LIMIT STOPS OFF PRESET TITLES OTHERS gt PARK TIME MIN OMIN AUTO PATROL 1 gt EXIT SCANSPEED 5DEG S SCAN TILT ANGLE 30DEG STOP TIME 10SEC MAX SPEED 400DEG S To set SCAN SPEED 1 Enter the preset command to access the main menu Refer to section 6 1 for the controller model and preset command 2 Position the cursor next to PAN TILT SETUP and press the OPEN button to access the Pan Tilt menu 3 Position the cursor next to SCAN SPEED and press the OPEN button to move the cursor to the right 4 Move the joystick up or down to set the speed 5 To accept the selection press the OPEN button or to cancel the selection press the CLOSE button 22 6 8 8 SCAN TILT ANGLE The tilt angle of the dome camera for auto scan random scan and frame scan can be set from 0 to 85 degrees or 92 degrees 0 degree is straight down Menu MAIN MENU lt CAMERA SETUP gt gt PAN TILT SETUP gt lt PRESET TITLES gt lt OTHERS gt PAN TILT MENU AUTO FLIP ON PROPORTIONALP T ON SCAN LIMIT STOPS OFF MANUAL LIMIT STOP
27. ing flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions the literature accompanying the appliance WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE CAUTION CONNECT 24V AC UL LISTED CLASS 2 POWER SUPPLY FIELD INSTALLATION MARKING THIS INSTALLATION SHOULD BE MADE BY A QUALIFIED SERVICE PERSON AND SHOULD CONFORM TO ALL LOCAL CODES FCC USA INFORMATION NOTE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference
28. instructions for information on inputting preset commands JK UC1 Input the desired preset using the numeric keypad Press the SHIFT key The LED will light up Press the PRESET key VLC485 Input the desired preset using the numeric keypad Press the key Press the PRESET key 6 4 PERFORMING PRESET OPERATIONS JK UC1 VLC485 Input the desired preset using the numeric keypad Press the PRESET button to perform the preset 6 5 PAN TILT FUNCTIONS Manual PAN Manual Pan is controlled from a keyboard and the speed ranges from 0 1 degrees sec to 90 degrees sec depending on the joystick position In turbo mode the speed is 150 degree sec However this speed is limited when Proportional P T is ON Manual TILT Manual Tilt speed ranges from 0 1 degrees sec to 45 degrees sec However this speed changes when Proportional P T is ON Pan Range 360 degrees continuous Tilt Range 85 degrees Indoor 92 degrees Outdoor Manual Pan Speeds 0 1 90 s Manual Pan Speeds turbo 150 s Manual Tilt Speeds 0 1 45 s Preset Speeds Pan 400 s max set in menu Tilt 200 s 6 6 SCAN FUNCTIONS AUTO SCAN The dome camera can perform an auto scan operation during power up or by direct control from a keyboard Scan limit stops ARE NOT set The dome camera will pan continuously until a manual pan tilt or zoom operation is performed from the keyboard Scan limit stops ARE set The dome camer
29. names and Locations Power Terminal 24VAC only Installation Notch Installation Label Screw for cover lock Reserved X18 Lens Control Terminal RS 422 Video out BNC connector Installation Brackets 3 legs RS 422 termination switch r Dome Base gt Dome Drive 5 Connections Basic connection Direct mode 24V AC UL listed class 2 power supply RS422 twisted pair ing AC Adaptor Monitor Keyboard Make sure to connect to a power supply that allows for at least 35W consumption RS422 Pin Out RX 2 wire a controller TX TX Dome Camera In the direct mode the communication line from the keyboard TX where TX is connected to RX of the dome camera and TX is connected to RX of the dome camera If connecting two or more dome cameras TX from the first camera is connected to RX of the second camera and TX is connected to the RX 6 Operation Power On display When the dome camera powers up the software version selected protocol and other information are displayed on the monitor TOSHIBA IK DP30A VERSION PROTOCOL TOSHIBA P ADDRESS 1 COMM 4800 N 8 1 6 1 ACCESSING THE MENU Accessing the menu varies with the model controller being used Several controllers are listed below Please refer to your model s instructions for information
30. on inputting commands JK UC1 Input 95 using the numeric keypad Press the PRESET button to display the MENU screen VLC485 Input 95 using the numeric keypad Press the PRESET button to display the MENU screen 6 2 Preset Commands The dome camera can set and perform various preset commands The following table lists the preset number and whether is can be set SET or performed GO Presets 1 32 and 35 66 are user presets Refer to your model s instructions for information on inputting preset commands Preset Number Function 1 32 SET GO Preset position 1 32 33 GO Flip 34 GO Home return to 0 pan position 35 66 SET GO Preset position 35 66 70 GO Begin Auto patrol 71 GO Backlight compensation ON 72 GO Backlight compensation OFF 73 GO One push WB 74 GO One push trigger AF 75 GO Software version Display 76 GO P T Initialize 83 SET Privacy Zone Setup menu mode 88 GO Color Mode IR Cut filter ON 89 GO Monochrome Mode IR Cut filter OFF 90 SET Set manual left limit stop 91 SET Set manual Right limit stop 92 SET Set Scan Left Limit Stop 93 SET Set Scan Right Limit Stop 95 SET Enter Menu Mode 96 GO Stop Scan 97 GO Begin Random Scan 98 GO Begin Frame Scan 99 GO Begin Auto Scan 6 3 PROGRAMMING PRESETS Programming presets varies with the model controller being used Several controllers are listed below Please refer to your model s
31. r temperatures from 2000K to 10000K AUTO automatically adjusts the white balance for color temperatures from 3000K to 7500K ONE PUSH WB can be set using 73 PRESET from a controller To change the White Balance 1 Enter the preset command to access the main menu Refer to section 6 1 for the controller model and preset command 2 Position the cursor gt next to CAMERA SETUP and press the OPEN button to access the Camera menu 3 Position the cursor next to WB and press the OPEN button to move the cursor to the right 4 Move the joystick up or down to select ATW AUTO or ONE PUSH WB 5 To accept the selection press the OPEN button or to cancel the selection press the CLOSE button 6 7 3 AE CONTROL Direct The lris can be controlled directly using OPEN or CLOSE controls Menu MAIN MENU CAMERA MENU AE MENU D CAMERA SETUP FOCUS MODE FULL AUTO lt PAN TILT SETUP gt WB ATW AUTO SLOW SHUTTEROFF lt PRESET TITLES gt gt lt gt SHUTTER SPEED 1 60 lt OTHERS gt ZOOM LIMIT X18 AE COMPENSATION 0 EXIT SHARPNESS 10 BACK LIGHT COMP OFF lt LINE LOCK gt DAY NIGHT AUTO PRIVACY ZONE 243 MODE AE mode can be set to FULL AUTO or SHUTTER PRIORITY FULL AUTO mode The shutter is fixed at 1 60 sec and the camera will automatically adjust the iris according to the level The iris can be controlled manually but will return to FULL AUTO if there is a zoom or pan tilt operation SHUTTER PRIORITY The shutt
32. rature of operation 32 to 122 F 0 to 50 C Preservation temperature 4 to 140 F 20 to 60 C Weight 1 8 kg Power supply AC24 V 10 60 Hz Power consumption 20 W Camera Image Sensor 1 4 type IT CCD High Sensitive CCD Number of Effective Pixels 768 H x 494 V Lens 18 x Zoom f 4 1 to 73 8 mm F1 4 to F3 0 Digital Zoom 12 x 216 x with optical zoom Angle of View H approx 48degree wide limit approx 2 7degree tele limit Sync System Internal Line lock AC Line lock phase adjustable Min Illumination 0 7 lux typ 1 60 0 05 lux typ 1 4 0 01 lux 1 4 IR Cut OFF S N Ratio more than 50 dB Resolution 480 TV lines typ Electronic Shutter 1 4 to 1 10000 sec White Balance Auto ATW One Push WB Gain Auto AE Control Full Auto Shutter Priority Manual Back Light Compensation On Off Auto Slow Shutter On Off On max 1 4sec Focusing System Auto Interval Zoom Trigger Manual Video Output NTSC VBS 1 0 Vp p Sync Negative 75 ohm Privacy Zone Masking 8 positions 37 Mechanical Pan Range 360 degrees continuous Tilt Range 92 degrees Outdoor Manual Pan Speeds 0 1 90 s Manual Pan Speeds turbo 150 s Manual Tilt Speeds 0 1 45 s Preset Speeds Pan 400 s Tilt 200 s Proportional P T Provided
33. s damaged b If liquid has been spilled or objects have fallen into the video product c If the video product has been exposed to rain or water d If the video product does not operate normally by following the operating instructions in the instruction manual Adjust only those controls that are covered by the instruction manual as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the video product to its normal operation e If the video product has been dropped or the cabinet has been damaged f When the video product exhibits a distinct change in performance this indicates a need for service 18 Replacement Parts When replacement parts be sure the service technician uses replacement parts specified by the manufacturer or have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards 19 Safety Check Upon completion of any service or repairs to this video product ask the service technician to perform safety checks to determine that the video product is in proper operating condition The CAUTION label shown on the left is attached on the camera A RISK OF ELECTRIC SHOCK A DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lighten
34. supply before cleaning 6 Attachments Do not use attachments not recommended by the video product manufacturer as they may cause hazards 7 Water and Moisture Do not use this video product near water Some examples are near a bath tub wash bowl kitchen sink or laundry tub in a wet basement or near a swimming pool 8 Accessories Do not place this video product on an unstable cart stand tripod bracket or table The video product may fall causing serious injury to a person or serious damage to the product Use only with stand tripod bracket or table recommended by the manufacturer or sold with the video product Any mounting of the product should follow the manufacturer s instructions and should use a mounting accessory recommended by the manufacturer 9 Ventilation This video product should never be placed near or over a radiator or heat register If this product is placed in a built in installation verify that there is proper ventilation so that the camera temperature operates within the recommended temperature range 10 Power Sources This video product should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supply to your location consult your product dealer Power Cord Protection Power cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them Pay particular attention to cords
35. t command 2 Position the cursor next to PAN TILT SETUP and press the OPEN button to access the Pan Tilt menu 3 Position the cursor next to PARK TIME MIN and press the OPEN button to move the cursor to the right 4 Move the joystick up or down to set the number of minutes 5 To accept the selection press the OPEN button or to cancel the selection press the CLOSE button 6 8 6 AUTO PATROL The Auto Patrol feature will repeat a pattern of up to 64 presets Limit stops are ignored during Auto Patrol The moving speed is fixed at 400 deg s when the STOP TIME is 10 seconds or more However it will become 90 deg s if a STOP time is less than 10 seconds Menu MAIN MENU PAN TILT MENU AUTO FLIP ON lt CAMERA SETUP gt PROPORTIONALP T ON b lt PAN TILT SETUP SCAN LIMIT STOPS OFF MANUAL LIMIT STOPS OFF PARKTIME MIN OMIN gt AUTO PATROL 1 gt EXIT SCAN SPEED 5DEG S SCAN TILT ANGLE 30DEG STOPTIME 10SEC MAX SPEED 400DEG S To enable AUTO PATROL 1 2 Enter the preset command to access the main menu Refer to section 6 1 for the controller model and preset command Position the cursor next to PAN TILT SETUP and press the OPEN button to access the Pan Tilt menu Position the cursor next to AUTO PATROL and press the OPEN button to move the cursor to the right Move the joystick up or down to scroll through the presets Move the joystick left or right to turn t
36. tical zoom is x18 x36 to x216 are the values for electronic zoom To change the zoom limit 1 Enter the preset command to access the main menu Refer to section 6 1 for the controller model and preset command 2 Position the cursor gt next to CAMERA SETUP and press the OPEN button to access the Camera menu 3 Position the cursor next to ZOOM LIMIT and press the OPEN button to move the cursor to the right 4 Move the joystick up or down to toggle between zoom limits 5 To accept the selection press the OPEN button or to cancel the selection press the CLOSE button 15 6 7 5 SHARPNESS MAIN MENU D CAMERA SETUP gt lt PAN TILT SETUP gt lt PRESET TITLES gt lt OTHERS gt EXIT CAMERA MENU lt FOCUS gt WB ATW lt AE gt ZOOM LIMIT gt SHARPNESS lt LINE LOCK gt PRIVACY ZONE X18 10 The sharpness can be controlled from 0 15 with 15 being the sharpest To change the SHARPNESS 1 Enter the preset command to access the main menu Refer to section 6 1 for the controller model and preset command 2 Position the cursor gt next to CAMERA SETUP and press the OPEN button to access the Camera menu 3 Position the cursor next to SHARPNESS and press the OPEN button to move the cursor to the right 4 Move the joystick up or down to select the sharpness level 5 To accept the selection press the OPEN button or to cancel the selection press the CLOSE buttons 6 7 6 LIN
37. tom of the screen Menu MAIN MENU TITLE MENU lt CAMERA SETUP gt D gt TITLE INPUT lt PAN TILT SETUP gt D PRESET TITLES TITLE POSITION UP OTHERS EXIT To set PRESET TITLES 1 2 3 Enter the preset command to access the main menu Refer to section 6 1 for the controller model and preset command Position the cursor next to PRESET TITLES and press the OPEN button to access the Title menu Press the OPEN button to move the cursor down to the title number Move the joystick up or down to scroll through title numbers Move the joystick to the right to input the title Move the joystick up or down to scroll through characters To accept the selection press the OPEN button or to cancel the selection press the CLOSE button Move the joystick down to TITLE POSITION and press open to choose UP or DOWN position of the title UP will display the title at the top of the screen and DOWN will display the title at the bottom of the screen To accept the selection press the OPEN button or to cancel the selection press the CLOSE button 25 6 10 OTHERS MENU 6 10 1 POWER UP During Power Up the dome camera can be set to start in various modes PARK The dome camera moves to Preset 1 position AUTO SCAN The dome camera performs an auto scan operation FRAME SCAN The dome camera performs a frame scan operation RANDOM SCAN The dome camera performs a random scan operation AUTO PATROL
38. turned ON The other dome camera is turned OFF It is OFF at the time of shipment ON and OFF are as in a figure POWER S301 TERMINAL on EJ BNC Connector 33 9 Installation JK H01A is a housing for ceiling mount of the Toshiba dome camera 1 IK DP30A Installation procedure 1 2 Carefully inspect to insure all parts are present and remove all parts from the box A template is included for ease in cutting the mounting hole First locate a position in the ceiling for a 9 020 08 2292mm hole to be drilled Trace around the template then cut a hole in the ceiling following the trace lines Note The thickness of a ceiling to which this housing can be attached is 0 08 1 77 2 45mm Remove the dome cover To Separate the dome cover from the housing turn the cover to the left with both hands This dome cover is connected to the top housing with the wire Fig 1 Loosen the lock screw according to ceiling board thickness for attaching to the ceiling Install the camera mounting screws that came with the camera Do not fully tighten the screws 34 1 Lock screw top housing install 6 Move the two support arms inside Fig 2 7 Remove knockout in the center of the housing and let the cable pass through Support Arms Fig 2 8 Put the video cable power cable and the Support wire is fixed here communication cable inside th
39. y Example Active Time auto Interval Time manual Active Time auto Interval Time manual The interval and active times can be set from 1 s to 255s In Zoom Trigger mode the camera remains in manual mode unless there is a zoom function After the zoom function is completed the camera returns to the manual mode The sensitivity of the Auto Focus can be set to NORMAL or LOW To change the Focus options 1 Enter the preset command to access the main menu Refer to section 6 1 for the controller model and preset command 2 Position the cursor next to CAMERA SETUP and press the OPEN button to access the Camera menu 3 Position the cursor next to FOCUS and press the OPEN button to access the Focus menu 4 Position the cursor next to the desired option and press the OPEN button to move the cursor to the right 5 Move the joystick up or down to select option setting 6 To accept the selection press the OPEN button or to cancel the selection press the CLOSE button 12 6 7 2 WHITE BALANCE CONTROL Direct The White Balance can be set by One Push Trigger operation Menu MAIN MENU CAMERA MENU gt CAMERA SETUP FOCUS PAN TILT SETUP gt WB ATW lt PRESET TITLES gt lt AE gt lt OTHERS gt ZOOM LIMIT X18 EXIT SHARPNESS 10 lt LINE LOCK gt PRIVACY ZONE The White Balance can be set to ATW Auto Tracking White AUTO ONE PUSHWB ATW automatically adjusts the white balance for colo
Download Pdf Manuals
Related Search