Toshiba IK-VR01A surveillance camera
Contents
1. VIDEO SWITCHER CAMERA1 TO AC 24V UL Listed class 2 power supply When connecting to DC power supply the Line Lock function is not activated CAMERA2 Note e The camera is synchronized to the power frequency of 60 1Hz covering a normal fluctuation of the power frequency However the camera may not cover a large fluctuation caused from the power generated by an engine generator etc It takes about 10 seconds or more until a stable synchronization is obtained after the power is turned on This is normal because several seconds are required to stabilize the camera against power noise Refer to 7 LINE LOCK PHASE for adjustment 6 INSTALLATIONS Connect the cable of the camera and the cable from the designated power supply with respective connectors Screws for fixing the camera and mounting base to the ceiling or wall are not supplied with the unit Use appropriate screws Note The weight camera body only is about 1 3kg The camera unit including the mounting base and the bracket weighs 2 1kg When installing to surfaces of other materials use the screws to fix it firmly 6 1 Adjust the Angle of View Security screws Top Cover Camera Base 1 Loosen the three security screws by the supplied special hexangular wrench and remove the top cover Important Notice Be sure to remove three silver screws immediately after removing the top co2. unit mm f Iis f Q LJ 170 H Bracket H Mounting Base unit mm LIMITED WARRANTY CCD SECURITY CAMERA The Imaging Systems Division of Toshiba America information Systems Inc ISD makes the following limited warranties with regard to this CCD Camera Product These limited warranties extend to the Original End User You r Three 3 Years Limited Warranty of Labor and Parts ISD warrants that this Product will perform in accordance with specifications for a period of three 3 years from the date of purchase by the Original End User During this three 3 years period ISD will repair or replace the P oduct if it does not perform as warranted In order to take advantage of this Limited Warranty You must a deiver the Product to an ISD Authorized Service Provider ASP and b pay all transportation and insurance charges for shipment of the Product to the ASP ISD reserves the right to substitute factory refurbished parts in place of those in need of repair Instruction Manual Owner s Manual You should read the Instruction Manual Owner s Manual thoroughly before operating this Product Before seeking warranty service you should check the troubleshooting guide in t
3. followed 5 Cleaning Disconnect this video product from the power supply before cleaning 6 Attachments Do not use attachments not recommended by the video product manufacturer as they may cause hazards 7 Water and Moisture Do not use this video product near water for example near a bath tub wash bowl kitchen sink or laundry tub in a wet basement or near a swimming pool and the like 8 Accessories Do not place this video product on an unstable cart stand tripod bracket or table The video product may fall causing serious injury to a child or adult and serious damage to the product Use only with stand tripod bracket or table recommended by the manufacturer or sold with the video product Any mounting of the product should follow the manufacturer s instructions and should use a mounting accessory recommended by the manufacturer 9 Ventilation This video product should never be placed near or over a radiator or heat register This video product should not be placed in a built in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer s instructions have been adhered to 10 Power Sources This video product should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supply to your location consult your product dealer 11 Power Cord Protection Power Supply cords should be routed so that they are not li
4. service personnel 17 Damage Requiring service Disconnect this video product from the power supply and refer servicing to qualified service personnel under the following conditions a When the power supply cord or plug is damaged b If liquid has been spilled or objects have fallen into the video product c If the video product has been exposed to rain or water d If the video product does not operate normally by following the operating instructions in the instruction manual Adjust only those controls that are covered by the instruction manual as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the video product to its normal operation e If the video product has been dropped or the cabinet has been damaged f When the video product exhibits a distinct change in performance this indicates a need for service 18 Replacement Parts When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer with the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards 19 Safety Check Upon completion of any service or repairs to this video product ask the service technician to perform safety checks to determine that the video product is in proper operating condition The CAUTION label shown on the left A RISK OF ELECTR
5. IC SHOCK A is attached on the camera DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightening flash with arrowhead WARNING symbol within an equilateral triangle TO REDUCE THE RISK OF FIRE OR is intended to alert the user to the ELECTRIC SHOCK DO NOT EXPOSE presence of uninsulated dangerous THIS APPLIANCE TO RAIN OR voltage within the products enclosure MOISTURE that may be of sufficient magnitude to constitute a risk of electric shock to CAUTION persons CONNECT 24V AC UL LISTED CLASS 2 pwe POWER SUPPLY The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance FIELD INSTALLATION WORDED THIS INSTALLATION SHOULD BE MADE BY A QUALIFIED SERVICE PERSON AND SHOULD CONFORM TO ALL LOCAL CODES FCC NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with th
6. Note the direction of the damper SA cushion N The groove should be face up Dome cover Gasket Top cover Dome replacement When the dome cover is damaged or to be replaced by a transparent cover call your distributor or sales person Firmly tighten three mounting screws Take care not to let dirt or foreign object enter between the parts 24 ki lt 7 LINE LOCK PHASE When a video switcher switches two or more cameras the picture may fluctuate on the video monitor due to the different AC line phase of each camera In this case adjust the V PHASE controller to get a stable image Line Lock V PHASE CONTROL 8 NOTE ON USE AND INSTALLATION Do not aim the camera at the sun Do not aim the camera at the sun or point it at sun even if you are not shooting Do not shoot intense light Intense light such as a spotlight may cause a bloom or smear A vertical stripe may appear on the screen However this is not a malfunction Treat the camera with care Do not drop the camera or subject it to strong shock of vibration Otherwise the camera may malfunction e Never touch internal parts Do not touch the internal parts ofthe camera other than the parts specified Otherwise the camera may malfunction Do not splash water on the camera Install the camera where the camera can be kept dry If the camera gets wet turn off the power and contact your d
7. SUBJECTED TO MISUSE ABUSE ACCIDENT IMPROPER INSTALLATION IMPROPER MAINTENANCE OR USE IN VIOLATION OF ISD S WRITTEN INSTRUCTIONS OR WHERE THE PRODUCT HAS BEEN ALTERED OR MODIFIED WITHOUT ISD S PRIOR AUTHORIZATION OR UPON THE REMOVAL OR ALTERATION OF ISD S FACTORY SERIAL NUMBER LABOR SERVICE CHARGES FOR PRODUCT INSTALLATION SET UP AND ADJUSTMENT OF CONTROLS ARE NOT COVERED BY THIS LIMITED WARRANTY No person agent distributor dealer authorized service provider or company is authorized to change modify or extend the terms of this Limited Warranty in any manner whatsoever The time within which an action must be commenced to enforce any obligation of ISD arising under this Limited Warranty or under any statute or law of the United States or any state thereof is herby limited to three 3 years from the date You discovered should have discovered the problem This limitation does not apply to implled warranties arising under state law Some states do not permit limitation of the time within which You may bring an action beyond the limits provided by state law so the above provision may not apply to You This Limited Warranty gives You specific legal rights and You may also have other rights which vary from state to state TOSHIBA AMERICA INFORMATION SYSTEMS INC Imaging Systems Division TOSHIBA 18
8. TOSHIBA INSTRUCTION MANUAL CCD COLOR CAMERA IK VR01A Please read this manual thoroughly before use and keep it handy for future reference Record in space provided below the Model No and the Serial No as found on the label on the bottom of this unit Model No IK VR01A Serial No Retain this information for future reference TABLE OF CONTENTS Important safeguards Features 8 Description iiiii in 3 Cautions hat Er aka da ena RAAR ea saa 3 Components ueuensnssnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnannn 3 Part Names amp Functions sssceceeceseeeseeeeeeeaaeesees 4 Connections and Operations nessneennnnnnnnn 5 Installations a een 7 Line Lock Phase uuusssssnseseeessnnnnnnnesennnnnnnennnennnnnenn 12 Note on use and Installation vrereeeoeeeoooooon 12 In Case of Problems uuuussseensnennnnnnnnnnnnnnnnnnnnnnnnnnnn 13 Specifications u un anna 14 Exterior View E E AE EAE E 15 _ a 70 10 00 N OTR O N gt IMPORTANT SAFEGUARDS 1 Read Instructions All the safety and operating instructions should be read before the product is operated 2 Retain Instructions The safety instructions and instruction manual should be retained for future reference 3 Heed Warnings All warnings on the product and in the instruction manual should be adhered to 4 Follow Instructions All operating and use instructions should be
9. connected refer to their operation manuals Coaxial cables for video signals and the power cord are not supplied with the camera Refer to the operations manuals of connected equipment for detailed wiring and overall operation instructions 5 1 Basic connection single system configuration Video Monitor BNC Connector Supplied Power Connector 12V DC q x POWER CORD twisted pair line minimum wire size of 18 AWG is recommended AG 120V 24V AC UL Listed Class 2 power supply 12V DC power supply CAUTION Never input 24V AC and 12V DC at the same time In case of DC12V connect 12 to red cable and GND to black cable Do not overload power supply Since this camera uses 24V AC UL Listed Class 2 power supply or 12V DC power supply it should be connected to a power supply that allows for at least 5w consumption Because the IK VR01A uses a mechanism a sufficient power supply with adequate current specifications is required 5 2 Line Lock Control Matching the vertical synchronization with the power frequency is called the Line Lock e This function is activated when the LL of Mode Setting Switch is on When two or more cameras are switched by the video switcher for viewing by a monitor TV the vertical sync phase can be locked with the power frequency and a stable vertical sync is obtained without being disturbed at the time of switching Video Monitor
10. cover 0 4 lux More than 10 of image output Tint dome cover Auto Gain Control AGC Average AGC 24dB Iris Control Mode Auto Iris Lens White Balance Auto White Balance Range 2500 K 10000 K Line lock Vertical phase adjustment Provided VR range 300deg Gamma compensation 0 45 Backlight Compensation BLC On Off DIP SW Video Output Signal VBS 1 0Vp p 750hm unbalance BNC Synchronization System Internal for DC or Linelock for AC 3 Mechanical Weight Camera 1 3kg Mounting Base 0 6kg Bracket 0 2kg Dimension Camera 170mm D x 150mm H with Mounting Base 175mm D x 155mm H 4 Optical Built in Lens Vari focus Lens f 3 0 8 0mm F1 0 Wide F1 45 Tele Auto Iris View Angle Wide 117 3 D 90 8 H 66 6 V Tele 45 2 D 36 2 H 27 0 V Focus Length 0 2m 5 Power Input Voltage DC12V or AC24V Power Consumption 3 0W 6 Environmental Operating Temperature 10 C 50 C 90 RH max Storage Temperature 20 C 60 C 70 RH max Water proof IP66 7 Regulation Safety UL2044 Dust and Water Resistance IP66 Emission FCC Class A DOC ClassA Design and specifications are subject to change without notice 14 11 EXTERIOR VIEW unit mm opted
11. e instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense USER INSTALLER CAUTION Your authority to operate this FCC verified equipment could be voided if you make changes or modifications not expressly approved by the party Serial No Label The serial No label is located here 2 1 FEATURES amp DESCRIPTION IK VRO1A has the following features 1 2 3 4 2 Flush Surface mount IP66 Standard for dust and water resistance Built in vari focal lens with auto iris Focal length 3 0 8 0mm Incorporated 1 3 type CCD image sensor gives high resolution and excellent sensitivity 480 lines horizontal resolution 0 4 Ix minimum illumination with tint dome cover 50dB Signal To Noise Ratio Power supply AC24V or DC 12V This camera automatically detects the power BLC AGC and Line Lock AC24V CAUTIONS 1 Avoid touching the lens glass with your fingers If necessary use a soft cloth moistened with alcohol to wipe off any dust Avoid aiming the camera at the sun Avoid shooting the camera at intense light Intense light such as a spotlight may cause a bloom or smear A vertical stripe may appear on the screen However this is not a malfunction Install the camera away from video noise If cables are w
12. ealer e Check the ambient temperature and humidity Avoid using the camera where the temperature is hotter or colder than specified Otherwise the quality of images may deteriorate or internal parts may be affected Special care is required to use the camera at high temperature and humidity e Should you notice any trouble If any trouble occurs while you are using the camera turn off the power and contact your dealer If you continue to use the camera when there is something wrong with it the trouble may much worse and an unpredictable accident may occur 12 9 IN CASE OF PROBLEMS Condition Check Points No image Are the camera and connected equipment turned on Are cables connected correctly Unnatural color Is the monitor TV adjusted correctly Is the lighting too weak The image is out of focus The image is dark Is the lens focus adjusted Is the lens or cover dirty Are there any large barrier or bright illumination near the camera Is the lens iris adjustment volume correctly set 13 10 SPECIFICATIONS 1 Image System Image Device 1 3 IT CCD Pixel Elements 771 H x 492 V 2 Electrical TV System 2 1 Interlace 15 734KHz Horizontal 59 94Hz Vertical Horizontal Resolution 480 TV lines S N Ratio 50dB TYP White 100 Weight On SC TRAP ON Minimum Illumination 0 2 lux More than 10 of image output Clear dome
13. he Instruction Manual Owner s Manual and follow the instructions to correct the problem How to Obtain Warranty Service Step by step Procedures To obtain warranty service You should 1 Contact Toshiba at 877 855 1349 for operation or installation assistance 877 855 1FIX 2 Contact an ASP for warranty service with in thirty 30 days after the Product fails to comply with specifications 3 Arrange for shipment of the Product to a Toshiba Authorized Service Provider 4 Securely pack the Product in the original carton and extemal shipping pack include a letter explaining the problem with a copy of the bill of sale or proof of purchase 5 Prepay all transportation and insurance costs Questions If you have any questions please check our wed site at http www toshiba com taisisd security Your Responsibilities This Limited Warranty is subject to the following conditions 1 You must provide the bill of sale or proof of purchase at the time that warranty service is required 2 You must notify an ASP within thirty 30 days after you discover that the product does not perform in accordance with specifications during the Limited Warranty period 3 All Warranty Service of this product must be by an ISD Authorized Service Provider 4 You must pack the Product in its original carton using the original packing material then insert the original carton containing the Product into another carton with additional packing materia before s
14. he ay 83 5 m brackets are not water resistant ge ION m Mounting Base center 55 mm Mounting Base Drain groove A Wall or Ceiling D Junction Box NI A Cable access hole b x 7 7 027 mm With female screw for piping Rear cable hole Drain groove In case of using the variable mounting Screws not supplied holes x4 Fix firmly Screws x3 Mount camera base with three supplied Mount the top cover the screws A Longer screw M4x16 assembly of the dome Tighten and lock the screws firmly cover and secure it firmly with three security screws by the supplied special hexangular wrench Top Cover Gr Align to this mark 6 2 2 Installation to Junction Box with Bracket Flush Mount Installation Screws not supplied ON x4 Note the direction of the bracket which has two sides Align the marks Screws x3 Mount camera base with three supplied screws B Shorter screw M4x10 Tighten and lock the screws firmly Mount the top cover the assembly of the top dome cover and secure it firmly with three security screws by the supplied special hexangular l wrench Gr Align to this mark 6 2 3 Change of Dome Cover _ Screws x3 amp oo Retainer plate Put the protruding side downward The protruding portion should be set IL in the groove of the shock damper p lt Shock damper cushion
15. hipping the Product to an ASP DISCLAIMERS ALL OTHER EXPRESS OR IMPLIED WARRANTIES ON THIS PRODUCT INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU IF THIS PRODUCT IS NOT IN GOOD WORKING ORDER AS WARRANTED ABOVE YOUR SOLE AND EXCLUSIVE REMEDY SHALL BE THE REPAIR OF REPLACEMENT OF THE PRODUCT IN NO EVENT WILL ISD OR ITS PARENT COMPANY OR ANY ASP BE LIABLE TO YOU OR ANY THIRD PARTY FOR ANY DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT THIS LIMITATION APPLIES TO DAMAGES OF ANY KIND INCLUDING ANY DIRECT OR INDIRECT DAMAGES LOST PROFITS LOST SAVINGS OR OTHER SPECIAL INCIDENTAL EXEMPLARY OR CONSEQUENTIAL DAMAGES WHETHER FOR BREACH OF CONTRACT TORT OR OTHERWISE OR WHETHER ARISING OUT OF THE USE OF OR INABILITY TO USE SUCH PRODUCT EVEN IF TAIS ITS PARENT COMPANY OR AN ASP HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR OF ANY CLAIM BY ANY OTHER PARTY SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR SOME PRODUCTS SO THE ABOVE LIMITATINS OR EXCLUSIONS MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE THIS LIMITED WARRANTY SHALL BE VOID IF THE PRODUCT OR PARTS HAVE BEEN
16. ired near electric lighting wires or a TV set noise may appear in images In this event relocate cables or reinstall equipment 3 COMPONENTS 1 Camera with Tint Dome Cover installed 1 pe 2 Accessories a Mounting Base 1 pc b Bracket 1 pe c ScrewA 3 pcs d Screw B 3 pcs e Clear Dome Cover 1 pc f Special Hexangular Wrench 1 pc g Monitor Out Harness Wire 1 pc h Power Connector 1 pc i Instruction Manual 1 pc 4 PART NAMES amp FUNCTIONS Lens lris ADJ Counterclockwise The picture becomes darker Clockwise The picture becomes brighter Optimum Value is at default setting Line Lock Phase ADJ Adjusts the phase of the line lock Mode Setting Switch BLC Backlight Compensation Switch With the switch on it adjusts the backlight automatically to obtain the best possible image LL Sets camera synchronization to line lock with the switch on Available only with AC24V Monitor Out Connector Connect with the supplied monitor out harness wire Used to adjust the angle of view when installing the camera 5 CONNECTIONS AND OPERATIONS Notes on connecting Power plugs to connected equipment must be disconnected before installation A 75 ohm coaxial cable 3C 2V or 5C 2V is required for standard connection For details of wiring and operation of equipment to be
17. kely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs screws and the point where they exit from the product 12 Installation This video product should be installed on a firm and solid part of the ceiling or wall If installed on a soft and weak place the camera unit may fall A person under it may be injured and things under it may be damaged 13 Lightning For added protection for this video product during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the power supply and cable system This will prevent damage to the video product due to lightning and power line surges However if there is thunder or lightning now do not touch the unit and any connected cable This will for you not to receive the electric shock by the serge of thunder 14 Overloading Do not overload power supply and extension cords as this can result in a risk of fire or electric shock 15 Object and Liquid Entry Never push objects of any kind into this video product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electrical shock Never spill liquid of kind on the video product 16 Servicing Do not attempt to service this video product yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified
18. ver The screws are used to temporarily fix the top cover for transportation Tilt rotation Horizontal rotation Focus lock lever NEAR Remove three silver Zoom screws transport protection lock lever Transport Protection Screws silver 2 The lens direction in pan direction can be adjusted by turning pan lock counterclockwise to unfasten it without moving the lens After adjustment turn pan lock clockwise to fasten it Note Do not turn the lens over 360 Otherwise the inner connector may be broken and the image may not appear 3 The lens tilt angle can be adjusted by loosening the tilt lock Q After adjusting tighten the tilt lock Q 4 Adjust the zoom position by loosening the zoom lock lever After adjusting tighten the zoom lock lever 5 Adjust the focus by loosening the focus lock lever After adjusting tighten the focus lock lever 4 6 Repeat the adjustments from step 1 to step 5 till the optimum image appears 6 2 Installing the Camera Unit 6 2 1 Installation to Wall or Ceiling with Mounting Base Surface Mount Installation 7 i Cable access hole g27 mm When installing the camera unit on the of mm wall mount it with the drain groove on the downside Do not block the drain Mounting Base center SU groove When installing the camera unit outdoor gt make waterproof for the cables The camera body is water resistant but t
Download Pdf Manuals
Related Search