Baumatic BTC9750GL cooker hood
Contents
1. o Use a screwdriver to remove the glass cover that sits over the bulb Unscrew the light bulb that needs to be replaced and insert a new G4 20W max bulb Then replace the glass cover o IMPORTANT Defective bulbs should be replaced immediately o If the lights still do not work make sure that the bulbs are fitted properly into their housings before you call for technical assistance o Refit the grease filter 14 Fitting the carbon filters If the appliance is being used to be used in recirculation mode then it is necessary to fit carbon filters This will help to absorb unpleasant odours caused by cooking IMPORTANT BEFORE ATTEMPTING TO FIT OR REMOVE THE CARBON FILTERS YOU MUST ENSURE THAT YOU HAVE DISCONNECTED THE COOKER HOOD FROM YOUR MAINS SUPPLY 1 Remove the grease filters 2 Hook the carbon filter over the pins that are located at the end of the motor 3 Turn the carbon filter anticlockwise until you feel it click into place o Repeat this process for the second carbon filter You need to place a carbon filter at either end of the motor o Refit the grease filter o The carbon filters should be replaced every three months or if they show signs of damage 15 Installation IMPORTANT Before installation and usage read all the instructions and make sure that the voltage V and the frequency Hz indicated on the rating plate are exactly the same as the voltage and frequency in your2. neutral or coloured black o The brown wire must be connected to the terminal marked L live or coloured red Before beginning installation O Check that the product purchased is of a suitable size for the chosen installation area In addition check whether there is an electrical socket available that will be accessible once the hood is mounted If the product is going to be used in extraction mode then there should also be space to connect a ducting hose to the outside Carry out all necessary masonry work prior to the fitting of the cooker hood Ensure that all electrical connections are carried out by a suitably qualified person Before commencing installation of the cooker hood the grease filters should be removed Check inside the product and insure that there is no transit packaging or any other materials such as packets of screws guarantees etc These should be removed and kept for future use If possible disconnect and move freestanding or slot in cookers from their position to provide easier access to the rear wall and ceiling If this is not possible then a thick protective covering Should be placed over the worktop hob top or cooker This will help to protect these surfaces from damage and debris Select a flat surface for assembling the cooker hood Cover that surface with a protective covering and place all cooker hood parts and fittings on to it Rawl plugs are provided to secure the ho
3. Instruction manual User Manual for your Baumatic BTC6750GL BTC9750GL Cooker Hood 60 cm Cooker hood with LCD display 90 cm Cooker hood with LCD display Baumatic You will be mine NOTE This User Instruction Manual contains important information including safety amp installation points which will enable you to get the most out of your appliance Please keep it in a safe place so that it is easily available for future reference for you or any person not familiar with the operation of the appliance DD 03 03 08 Contents Page Environmental note IMPORTANT SAFETY INFORMATION Specifications of your BTC6750GL cooker hood Specifications of your BTC9750GL cooker hood Using your Baumatic cooker hood Before first use To use your cooker hood Setting the time of day The timer Cleaning your Baumatic cooker hood Cleaning The grease filter Maintenance Removing and cleaning the grease filter Changing a light bulb Fitting the carbon filters Installation Electrical connection Before beginning installation Installing your cooker hood Connecting to external ducting Fitting the chimney Attaching the glass canopy BTC9750GL only Completing the installation Extraction mode or recirculation mode Troubleshooting Contact details 10 11 10 10 11 11 11 12 12 12 13 15 13 14 15 16 25 16 17 17 18 18 20 21 ZA 25 24 25 25 26 27 28 ENVIRONMENTAL NOTE
4. and cleaning DO NOT CLEAN IN BEHIND THE GREASE FILTERS If the room where the cooker hood is to be used contains a fuel burning appliance such as a central heating boiler then its flue must be of the sealed or balanced flue type If other types of flue or appliances are fitted ensure that there is an adequate supply of air in the room When the hood is being used in its extractor function ensure that the ducting is fire retardant and that there are no bends Sharper than 90 degrees as this will reduce the efficiency of the hood Ensure the ducting for the extractor function has the same diameter as the outlet hole all the way through Keep young children from using playing with or tampering with the cooker hood Older children and infirm persons should be supervised if they are using the cooker hood Your cooker hood is for domestic use only Please dispose of the packing material carefully children are especially vulnerable to it Dirty oil is an even greater fire risk Always put lids on pots and pans when cooking on a gas cooker The manufacturer refuses to accept any responsibility for damages arising to the hood or it catching on fire from a failure to observe the fire safety advice contained in this instruction booklet o Remember that when in extraction mode your cooker hood is removing air from your room Ensure that proper ventilation measures are being observed o Note that it removes odours f
5. home The rating plate can be found behind the grease filter The manufacturer declines all responsibility in the event of the installer failing to observe all the accident prevention regulations in force which are necessary for normal use and the regular operation of the electric system Electrical connection YOUR COOKER HOOD IS INTENDED FOR FITTED AND PERMANENT INSTALLATION o The cooker hood s power cable must be fitted upstream from the electrical connection using an omni polar switch with a contact distance of at least 3 mm THE FUSE MUST BE RATED AT 3 AMPS WARNING THIS APPLIANCE MUST BE EARTHED It Should only be connected by a competent person using fixed wiring via a double pole switched fused spur outlet UK ONLY We recommend that the appliance is connected by a qualified electrician who is a member of the N I C E I C and who will comply with the I E E and local regulations The wires in the mains lead are coloured in accordance with the following UK code Blue Neutral Brown Live Green Yellow Ground If you only find two wires in the main s lead blue and brown then neither must be connected to the earth terminal 16 O USE A 3 AMP FUSE As the colours of the wires in the appliance s mains lead may not correspond with the coloured markings identifying the terminals in your spur box please proceed as follows o The blue wire must be connected to the terminal marked N
6. onto the support screws 7 Fully tighten the support screws A and then screw the anchoring screws B through the relevant holes in the cooker hood Tighten the anchoring screws fully into the wall 20 Connecting to external ducting 8 Connect the coupling to the top of the cooker hood and then connect a 125 mm ducting hose to the coupling please note that the ducting hose is not supplied with the appliance o The other end of the ducting hose should be connected to your discharge outlet that is suitable for cooking vapours It should have across section of at least 150 cm2 o The maximum distance between the coupling and your discharge outlet should be 3 metres with one 90 degree bend Fitting the chimney 9 Take the two chimney sections C and D o Rest the bottom of chimney section C on the top of the hood You Should take care to position the tabs on the chimney section into the rear of the hood u Bi mM Pea 2 a Par at a 2 Pr ad 2 2 oa a Fi o Mark the side measurement of both sides of chimney section C on the wall with a pencil 21 10 Lift chimney section D upwards until it reaches the ceiling You must ensure that it is perpendicular to the hood o Mark the side measurement of both sides of chimney section D on the wall with a pencil and then remove chimney section D 11 Take the fixing bracket E and place it between the two penci
7. tightened otherwise excessive pressure could be placed on the glass section 24 Completing the installation If you are setting the appliance to recirculation mode then you should now fit the two carbon filters See the Fitting the carbon filters section on page 15 The electrical connection must correspond to the electrical requirement noted on the rating plate which is placed inside the cooker hood The appliance should now be connected to the electrical supply See page 16 17 for detailed information on the electrical connection Use a stainless steel cleaner on the stainless steel sections of the appliance Refit the grease filter and then switch on the mains supply to the appliance Check that the appliance is operating correctly by selecting each speed and switching the light bulbs on and off Extraction mode or recirculation mode What is the difference between extraction and recirculation modes To get optimum performance from your cooker the air will be taken out of the room via external ducting Unfortunately if you live in a flat or the hood is too far from an outside wall this may not be possible The only alternative is to recirculate the alr In recirculation mode stale air is taken via the grease filter and passed through a charcoal filter for purification The air then re enters the kitchen via an opening in the hood What ts a charcoal filter and do I need one All cooker hoods have a greas
8. 911 DO NOT ATTEMPT TO REPAIR THE APPLIANCE YOURSELF Please note that if an engineer is asked to attend whilst the product is under guarantee and finds that the problem is not the result of an appliance fault then you may be liable for the cost of the call out charge The appliance must be accessible for the engineer to perform any necessary repair If your appliance is installed in such a way that an engineer is concerned that damage will be caused to the appliance or your kitchen then he will not complete a repair This includes situations where appliances have been tiled in sealed in with sealant have wooden obstructions placed in front of the appliance like plinths Or any installation other than the one specified by Baumatic Ltd has been completed Please refer to the conditions of guarantee that appear on the warranty card that you receive with the appliance 21 o gt Baumatic You will be mine United Kingdom Baumatic Ltd Baumatic Buildings 6 Bennet Road Reading Berkshire RG2 0QX United Kingdom Sales Telephone 0118 933 6900 Sales Fax 0118 931 0035 Service Telephone 0118 933 6911 Service Fax 0118 986 9124 Spares Telephone 01235 437244 Technical Advice Telephone 0118 933 6933 E mail sales baumatic co uk technical baumatic co uk Website www baumatic co uk Republic of Ireland 01 6266 798 Czech Republic Baumatic CR spol s r o Amperova 495 46215 Libr
9. EY SECTION 2 6 mm x 303 mm Your stainless steel cooker hood is fitted with High extraction tangential motor Touch control operation LCD display 3 speeds 1 metallic grease filter 2 halogen lights Cut off timer O O O QO O O O Extraction capacity 750 m3 hr Noise level min max 58 64 dB MODEL NUMBER CARBON FILTER REQUIRED BTC6750GL Specifications of your BTC9750GL cooker hood 1045 Ja 56 min PRODUCT DIMENSIONS Height 565 mm 1045 mm Width 900 mm Depth 500 mm DIMENSIONS OF CHIMNEY SECTION 2 6 mm x 303 mm Your stainless steel cooker hood is fitted with High extraction tangential motor Touch control operation LCD display 3 speeds 1 metallic grease filter 2 halogen lights Cut off timer O O O QO O O O Extraction capacity 750 m3 hr Noise level min max 58 64 dB MODEL NUMBER CARBON FILTER REQUIRED BTC9750GL Using your Baumatic cooker hood Before first use IMPORTANT THIS PROCESS MUST BE FOLLOWED VY BEFORE THE COOKER HOOD IS USED FOR THE FIRST TIME o You should use a good quality stainless steel cleaner on ALL of the stainless steel areas of your cooker hood before it is used for the first time o This will help to leave a silicone water resistant film to protect the stainless steel surfaces To use your cooker hood o Make sure that it has been installed by a suitably qualified person as per the information contained in Baumatic s installatio
10. Note Before discarding an old appliance switch off and disconnect it from the power supply Cut off and render any plug useless Cut the cable off directly behind the appliance to prevent misuse This should be undertaken by a competent person CONFORMITY TO W E E E DIRECTIVE This appliance is marked according to the European directive 2002 96 EC on Waste electrical and Electronic Equipment WEEE By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The symbol dit on the product or on the documents accompanying the product indicates that this appliance may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment Disposal must be carried out in accordance with local environmental regulations for waste disposal For more detailed information about treatment recovery and recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product IMPORTANT SAFETY INFORMATION Your safety is of the utmost importance to Baumatic Please make sure that you read this instruction booklet before attempting to install or use the appliance If you are unsure of any of the information conta
11. e filter but if you are using your cooker hood in recirculation mode then a charcoal filter must be fitted in addition to the grease filter 25 Troubleshooting IMPORTANT If your cooker hood appears not to be operating properly before contacting the Baumatic Service Department please refer to the checklist below D My cooker hood will not start o Check that the hood is connected to the electricity supply o Check that the fan speed control is set correctly D My cooker hood is not working effectively o The fan speed is not set high enough o The grease filters are dirty and require cleaning o The kitchen is not well ventilated enough o Ifthe hood is set up for recirculation mode check that the carbon filters do not need replacing o Ifthe hood is set up for extraction mode check that the ducting hose and discharge outlet are not blocked D My cooker hood has switched off during operation o The safety cut out device has been tripped o Turn off the hob and then wait for the safety cut out device to reset o IMPORTANT If you have installed your cooker hood too low the safety cut out device will frequently trip Your cooker hood may become damaged if the safety cut out device is tripped frequently 26 IMPORTANT If your appliance appears not to be operating correctly then you should disconnect it from your mains supply and then contact the Baumatic Service Department on telephone number 0118 933 6
12. ec Czech Republic 420 800 185 263 www baumatic cz Slovak Republic Baumatic Slovakia s r o Skultetyho 1 831 04 Bratislava 3 Slovakia 421 255 640 618 Germany Baumatic Gmbh Janderstrasse 9 Mannheim 68199 Germany 4962 112 9190 www baumatic de Italy Baumatic Italia S R L Via Caltana 129 Campodarsego Padova 35011 Italy 3904 9920 2297 www baumatic it Holland Baumatic Benelux B V Grindzuigerstraat 22 1333 MS ALMERE The Netherlands 3136 549 1555 www baumatic nl 28 30 31 Baumatic WWW baumatic com
13. ined in this booklet please contact the Baumatic Technical Department IMPORTANT Any installation work must be carried out by a qualified electrician or competent person o The hood must be installed in accordance with the installation instructions and all measurements followed o If the cooker hood is installed for use above a gas appliance then the provision for ventilation must be in accordance with the Gas Safety Codes of Practice BS 6172 BS 5440 amp BS 6891 Natural Gas and BS 5482 LP Gas 1994 the Gas Safety Installation amp Use Regulations the Building Regulations issued by the Department of the Environment the Building Standards Scotland Consolidated Regulations issued by the Scottish Development Department o It is dangerous to alter the specifications or to modify this product Do not tamper with it or attempt to modify the appliance in any way o When installing the hood ensure that the following recommended distances are observed between the highest point on the hob top including the burners and the bottom of the cooker hood gt Electric cookers 700 mm gt Gas cookers 700 mm gt Coal oil cookers 800 mm IMPORTANT DO NOT SET YOUR COOKER HOOD LESS THAN 700mm ABOVE YOUR COOKER o When installed between adjoining wall cabinets the cabinets must not overhang the hob The edges of the cooker hood are sharp be mindful of this as you handle your appliance especially during installation
14. l marks that you made in step 9 o Keeping the bracket in contact with the wall use a pencil to mark on the wall the anchoring holes that are cut out of the bracket 22 12 Using a 8 mm drill bit drill out two holes on the pencil markings that you made in step 11 Insert raw plugs into the holes and then use a screwdriver to secure the fixing bracket to the wall o Refit chimney section C to the hood and fix it onto the hood using the two screws that are supplied o Secure the top of chimney section C to the fixing bracket using the screws provided o Slide chimney section D inside of chimney section C Then secure the upper bracket to the wall using the same method as you have just used to secure the lower bracket 13 Lift chimney section D up to the ceiling and secure it to the fixing bracket using the screws provided 23 Attaching the glass canopy BTC9750GL only o The anchoring bolts F should be found with the other brackets and screws provided with the cooker hood If you find them already attached to the cooker hood then you should unscrew them o Carefully place the glass section Q on the upper surface of the cooker hood and then slide it back towards the wall o Screw the anchoring bolts F through the relevant holes in the glass section Q o IMPORTANT You must ensure that the glass section is securely held in place by the anchoring bolts However the anchoring bolts must not be over
15. lters The grease filter O O O O Your cooker hood includes a grease filter which helps to absorb grease particles to protect your kitchen amp furniture from greasy residues This metallic filter may become inflammable if they become saturated with this greasy residue To prevent this fire hazard the filter should be cleaned regularly Depending on use this should be done every 10 15 days or at least once a month using hot water and normal washing up detergent DO NOT WASH THE GREASE FILTER IN A DISHWASHER 12 Maintenance Removing and cleaning the grease filter o First remove the grease filter by pulling down on the handle and pulling them away from the cooker hood o Soak the grease filter in hot water and washing up liquid for about an hour o Rinse it off thoroughly with hot water o Repeat the process if required o Refit the grease filter once it has dried o IMPORTANT Let the grease filter dry thoroughly before refitting it in the cooker hood 13 Changing a light bulb IMPORTANT BEFORE ATTEMPTING TO CHANGE A LIGHT BULB YOU MUST ENSURE THAT YOU HAVE DISCONNECTED THE COOKER HOOD FROM YOUR MAINS SUPPLY o Remove the grease filter as described on page 13 o Prior to touching the light bulbs ensure that they have cooled down o Find the bulb that requires replacement you will find it located in the light fixture which is inside the exposed section of the Canopy
16. n instructions o Find the control panel which is located in the middle of the canopy o There are several buttons on the control panel which perform separate functions o Press the Add ON button to switch the cooker hood on The hood will start to run at its lowest speed o The cooker hood has three operating speeds low medium and high Use the Add ON button to increase the speed and use the Dec OFF button to decrease the speed that it is operating at o The operating speed that you have selected will appear on the LCD display o If you press the Dec OFF button when the hood is operating at its lowest speed then the hood will switch off 10 o Press the Light button to switch the bulbs on and off You can switch the lights on even if the hood is not operating IMPORTANT IDEALLY YOU SHOULD TURN ON YOUR HOOD TEN MINUTES BEFORE YOU START TO COOK OR AT THE VERY LEAST WHEN YOU BEGIN COOKING YOU SHOULD ALSO RUN YOUR HOOD FOR TEN MINUTES AFTER YOU HAVE FINISHED COOKING Setting the time of day o Press and hold the timer button until the first two digits of the display start to flash o Release the timer button then use the Add ON button and Dec OFF button to set the hour time o Press the timer button again and the second two digits of the display will start to flash o Use the Add ON button and Dec OFF button to set the minute time o Once the time of day is shown correctly on the display press the time
17. od to most types of walls and ceilings However a qualified technician must verify the Suitability of the materials in accordance with the type of wall and ceiling The wall and ceiling must be strong enough to take the weight of the hood 17 o Do not tile grout or silicone this appliance to the wall This appliance is designed to be surface mounted only Installing your cooker hood IMPORTANT YOU WILL HAVE TO DECIDE BEFORE INSTALLING YOUR COOKER HOOD WHETHER TO USE IT IN EXTRACTION MODE OR RECIRCULATION MODE PLEASE TURN TO PAGE 24 NOW TO UNDERSTAND THE DIFFERENCES BETWEEN THESE TWO MODES o We recommend that at least two people install this hood IMPORTANT YOUR COOKER HOOD SHOULD BE CONNECTED TO YOUR MAINS SUPPLY AFTER THE REST OF THE INSTALLATION PROCESS HAS BEEN COMPLETED 1 Remove the metal grease filters 2 Position the hood against the wall that you are intending to install it on and mark the position of the support holes that are to be drilled as shown in the figure below 18 2a The support screw holes are indicated by figure A in this drawing and the anchoring screw holes are indicated by figure B a 3 Using a drill bit with a 8 mm diameter make holes in the wall on the positions that you have marked in step 2 4 Insert raw plugs into all of the holes that you have drilled 5 Fasten the support screws halfway in leaving them 10 mm out of the wall 19 6 Hang the hood
18. r button for the third time to confirm it The timer o You can use the cooker hood s timer to set the cooker hood to run for a particular period of time and then switch off o You can get the cooker hood to countdown for the following periods of time No of pushes of the timer Length of time in minutes button the cooker hood will operate for Timer function cancelled o Once you have set a countdown period the cooker hood will start to countdown The time remaining until the cooker hood shuts off will show on the display o When the countdown time has been reached 00 00 will appear and the cooker hood will stop running 11 Cleaning your Baumatic cooker hood IMPORTANT BEFORE CLEANING ALWAYS ENSURE THAT YOU HAVE SWITCHED YOUR COOKER HOOD OFF AT THE OMNI POLAR SWITCH SET AT THE WALL FROM THE CABLE Cleaning O Clean the external parts of your cooker hood with mild liquid detergent and a new damp cloth Never use abrasive powder corrosive solvents or brushes Never insert pointed objects into the motor s protective grid Only clean the control panel and grease filter grill with mild liquid detergents and a new damp cloth If you are using the appliance in recirculation mode then be Sure to replace the carbon filter at the recommended interval see section on Fitting the carbon filter A build up of grease could cause a fire hazard Never attempt to clean the area above the grease fi
19. rom your room not steam o Warning Always ensure that the cooker hood has been disconnected from the power supply before carrying out any work on the hood including replacing light bulbs o Do not connect the ducting system of this appliance to any existing ventilation system which is being used for any other purpose o Do not install above a cooker with a high level grill o Never leave frying pans unattended during use as overheated fats and oils might catch fire o Do not leave naked flames under the cooker hood o Do not attempt to use the cooker hood if it is damaged in any way Never attempt to use it without the grease filters fitted or if the filters are excessively greasy o Never flamb cook under this cooker hood o The lights on this appliance should only be used during operation of the cooker hood They should not be left on permanently and used as a lighting source o The cooker hood should not be exposed to a direct heat source from the cooking device underneath it i e a naked flame from a gas burner or heat from electric hob zones without a pan on them THE MANUFACTURER DECLINES ALL RESPONSIBILITY IN THE EVENT OF FAILURE TO OBSERVE THE INSTRUCTIONS GIVEN HERE FOR INSTALLATION MAINTENANCE AND SUITABLE USE OF THE HOOD Specifications of your BTC6750GL cooker hood oat un Te Ta min PRODUCT DIMENSIONS Height 565 mm 1045 mm Width 600 mm Depth 500 mm DIMENSIONS OF CHIMN
Download Pdf Manuals
Related Search