Smeg PX140 hob
Contents
1. 8 2 2 The pan stands Remove the pan stands and wash them in warm water with a non abrasive detergent taking care to remove all deposits Replace them on the hob following the instructions provided in point 7 1 Fitting the Pan Stands 8 2 3 The flame diffuser rings The burner caps and flame diffuser rings can be removed for easier cleaning wash them in hot water and non abrasive detergent taking care to remove all deposits and wait for them to dry completely The burner pins A must be fitted into the recesses B in the flame diffuser ring The holes C in the flame diffuser ring must mate with the ignition plugs and thermocouples D on the hob 8 2 4 The plugs and thermocouples For best performance the ignition plugs and thermocouples must always be kept thoroughly clean Check them frequently and if necessary clean them with a wet cloth Remove any dry residues with a wooden toothpick or a needle 342. 2 Adjusting for bottled gas SZ After adjusting for use of a gas other than the gas used for testing the appliance r ern replace the label on the casing with the label for the new gas The label is supplied in Se the bag with the LPG nozzles G30 G31 5 8 Hob burner layout Burner type 1 Auxiliary 2 Semi rapid 3 Rapid 4 Ultra rapid 5 9 Greasing the gas taps Over time the gas taps may become stiff or jam Clean their insides and change their lubricating grease This operation must be carried out by a skilled technician 1 i ae 28 pace Instructions for the Installer 6 Description of controls 6 1 The front panel All the hob s control and monitoring devices are placed together on the front panel CONTROL AREA Da N 4 Burner Hob KNOB OPERATING MODE To light the flame press the knob and at the same time turn it anti clockwise to a the minimum flame symbol To adjust the flame turn the knob to the zone between the maximum and the minimum settings To turn off the burner turn the knob back to the O position KNOB BURNER COMBINATIONS 29 Instructions for the User r 7 Using the hob Check that the burners flame diffuser rings and pan stands are fitted correctly The projections A on the flame diffuser rings must be fitted into the recesses B in the burner The holes C in the burner must mate with the i
3. 1 2 gas thread ISO 228 1 Connection with copper pipe The connection to the gas supply mains must be made so that no stresses or strains of any kind are applied to the appliance The connection can be made using the adapter unit D with two conical elements always fitting the gasket C supplied Connection with steel hose use only continuous wall stainless steel hoses compliant with the relevant m regulations and always fit the gasket C supplied B between the fitting A and the hose E jl When connecting with a hose ensure that the total length of the pipeline is not more than 2 metres also ensure that the hoses do not touch moving parts and are not crushed 4 1 Bottled gas connection Use a pressure regulator and make the connection to the gas cylinder in accordance with the relevant regulations Make sure that the gas supply pressure is as stated in the table in point 5 2 Adjusting for bottled gas 4 2 Room ventilation The appliance may only be installed in a permanently ventilated room as specified by the relevant regulations The air flow into the room where the appliance is installed must be sufficient for proper gas combustion and room ventilation The air intakes protected by gratings must be of suitable size see relevant regulations and located so that they cannot be even partially obstructed The kitchen must be kept properly ventilated to disperse the heat and humidity produced by cooking proces
4. G THE INSTRUCTIONS PROVIDED LATER IN THIS MANUAL IF THE APPLIANCE FAILS TO OPERATE DISCONNECT IT FROM THE ELECTRICAL MAINS AND CONTACT YOUR NEAREST SERVICE CENTRE NEVER ATTEMPT TO REPAIR THE APPLIANCE YOURSELF AFTER EACH USE OF THE HOB ALWAYS CHECK THAT THE CONTROL KNOBS ARE TURNED TO ZERO OFF NEVER PLACE PANS WITH BOTTOMS WHICH ARE NOT PERFECTLY FLAT AND SMOOTH ON THE HOB PAN STANDS NEVER USE PANS OR GRIDDLE PLATES WHICH PROJECT BEYOND THE OUTSIDE EDGE OF THE HOB THE NAMEPLATE WITH THE TECHNICAL DATA SERIAL NUMBER AND MARK IS IN A VISIBLE POSITION UNDERNEATH THE CASING ANNEXED TO THIS MANUAL AND APPLIED TO THE QUALITY CERTIFICATE THIS NAMEPLATE MUST NEVER BE REMOVED THE APPLIANCE IS INTENDED FOR USE BY ADULTS KEEP CHILDREN AT A SAFE DISTANCE AND NEVER ALLOW THEM TO PLAY WITH IT THIS APPLIANCE IS TAGGED UNDER EUROPEAN DIRECTIVE 2002 96 EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT WEEB THIS DIRECTIVE CONTAINS THE REGULATIONS GOVERNING THE COLLECTION AND RECYCLING OF DECOMMISSIONED APPLIANCES THROUGHOUT THE EUROPEAN UNION The manufacturer declines all responsibility for injury or damage caused by failure to comply with the above regulations or deriving from tampering with even just one part of the appliance and the use of non original spare parts v D Instructions for the Installer 2 Fitting the appliance in the top The procedures required below must be carried out by a skilled builder and or joi
5. Table of Contents 1 Precautions for safety and use 20 2 Fitting the appliance in the top 21 2 1 Fixing to the supporting structure 21 2 2 Fitting the gasket 22 2 3 Fixing using brackets 22 3 Electrical connection 23 4 Gas connection 24 4 1 Bottled gas connection 24 4 2 Room ventilation 24 4 3 Combustion gas discharge 24 5 Adapting to different types of gas 25 5 1 Removing the hob skin 25 5 2 Adjusting for bottled gas 26 5 3 Adjusting for natural gas 27 5 4 Adjusting the primary air flow 27 5 5 Reassembling the hob skin 28 5 6 Adjusting the minimum for natural gas 28 5 7 Adjusting the minimum for bottled gas 28 5 8 Hob burner layout 28 5 9 Greasing the gas taps 28 6 Description of controls 29 6 1 The front panel 29 7 Using the hob 30 7 1 Fitting the Pan Stands 30 7 2 Lighting burners with safety device 32 7 3 Practical hints for using the burners 32 7 4 Pan diameters 33 8 Cleaning and maintenance 34 8 1 Cleaning the hob 34 8 2 Cleaning the components 34 THESE INSTRUCTIONS ONLY APPLY TO THE COUNTRIES OF DESTINATION WHOSE IDENTIFICATION SYMBOLS ARE LISTED ON THE COVER OF THIS MANUAL THIS BUILT IN HOB IS CLASSIFIED AS CLASS 3 INSTRUCTIONS FOR THE INSTALLER these are intended for the qualified engineer who is to check the gas supply system and install commission and test the appliance INSTRUCTIONS FOR THE USER these provide recommendations for use a description of the controls and the correct procedures for cleaning a
6. d max in cm 1 Auxiliary 2 Semi rapid 7 18 3 Rapid 10 24 4 Ultra rapid 18 24 20 26 33 ome Instructions for the User 8 Cleaning and maintenance Before carrying out any operations disconnect the appliance from the ri electricity supply AN Never use a jet of steam for cleaning the appliance 8 1 Cleaning the hob ce B To keep the hob in good condition it must be cleaned regularly after each use first N allowing it to cool 8 1 1 Routine daily glass hob cleaning When cleaning and caring for glass surfaces always use only specific products which do not contain abrasives or chlorine based acids Instructions for use pour the product onto a damp cloth and wipe over the surface then rinse thoroughly and dry with a soft cloth or chamois leather 8 1 2 Food stains or spills Never use metal scouring pads or sharp scrapers which will damage the ts surface x Use ordinary non abrasive products for glass with the aid of non scratching sponges and wooden or plastic utensils if necessary Rinse thoroughly and dry with a soft cloth or chamois leather CU 8 2 Cleaning the components Never clean the knobs with aggressive products containing alcohol or steel or glass cleaners since they might cause permanent damage op The components described below must never be washed in a dishwasher 8 2 1 The knobs The knobs must be cleaned with a soft cloth dipped in warm water and dried thoroughly They can easily be lifted off
7. gnition plugs and thermocouples D on the hob 7 1 Fitting the Pan Stands The pan stands are supplied dismantled from the hob To place each pan stand on its burner correctly follow the instructions provided below Each pan stand must be positioned on the corresponding burner in order to guarantee proper operation Be very careful to match the different central diameters of the pan stands to the flame spreader crowns At the ends of the legs of the pan stands there To position the pan stand you are silicone gaiters with a hole that must be first need to centre the fixing centred onto the matching fixing pins on the pins 1 and 2 and then lower hob it until it is resting on the hob When properly positioned the legs of the pan stands must not hang above the hob but should rest on top of it 30 Instructions for the User we ED Make sure that the pan stands are simply fitted over their burners and are not left in a raised or tilted position if this occurs repeat the fitting procedure WRONG ppoe mi pan Soy peg WRONG RIGHT After performing the operations described above for each pan stand the hob will be as shown below with the feet of the pan stands forming a pattern of horizontal and vertical lines If a pan wobbles noticeably check that the pan stands have not been fitted incorrectly 31 32 4 S M N Instructi
8. nd maintaining the appliance X os 19 vas 1A Y 20 Precautions for Safety and Use 1 Precautions for safety and use THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE TAKE GOOD CARE OF IT AND KEEP IT TO HAND THROUGHOUT THE HOB S LIFE CYCLE USERS ARE ADVISED TO READ THIS MANUAL AND ALL THE INSTRUCTIONS IT CONTAINS BEFORE USING THE HOB ALSO KEEP THE SET OF NOZZLES PROVIDED IN A SAFE PLACE INSTALLATION MUST BE CARRIED OUT BY QUALIFIED STAFF IN COMPLIANCE WITH THE RELEVANT REGULATIONS THIS APPLIANCE IS INTENDED FOR HOUSEHOLD USE AND COMPLIES WITH THE EEC DIRECTIVES CURRENTLY IN FORCE THE APPLIANCE IS BUILT TO PROVIDE THE FOLLOWING FUNCTION COOKING AND HEATING FOODS ALL OTHER USES ARE TO BE CONSIDERED IMPROPER THE MANUFACTURER DECLINES ALL LIABILITY FOR USES OTHER THAN THOSE STATED ABOVE NEVER LEAVE PACKAGING RESIDUES UNATTENDED IN THE HOME SEPARATE WASTE PACKAGING MATERIALS BY TYPE AND CONSIGN THEM TO THE NEAREST SEPARATE DISPOSAL CENTRE THE APPLIANCE MUST BE CONNECTED TO EARTH IN COMPLIANCE WITH ELECTRICAL SYSTEM SAFETY REGULATIONS THE PLUG TO BE CONNECTED TO THE POWER SUPPLY LEAD AND THE RELATIVE SOCKET MUST BE OF THE SAME TYPE AND COMPLY WITH THE RELEVANT REGULATIONS THE POWER SUPPLY SOCKET MUST BE ACCESSIBLE EVEN AFTER THE APPLIANCE HAS BEEN BUILT IN NEVER DISCONNECT THE PLUG BY PULLING ON THE POWER SUPPLY LEAD IMMEDIATELY AFTER INSTALLATION CARRY OUT A QUICK TEST ON THE HOB FOLLOWIN
9. ner The hob can be installed on various materials including masonry metal solid wood and wood finished with plastic laminates provided the material is heat resistant T 90 C 2 1 Fixing to the supporting structure Make a hole in the cabinet top with the dimensions shown here maintaining a distance of at least 100 mm from the rear edge This appliance may be installed against walls higher than the worktop surface provided the distance shown here is maintained in order to prevent damage due to overheating Make sure that there is at least 750 mm between the hob burners and a shelf or hood if any placed vertically above them If the hob is installed above an oven the oven must be fitted with a cooling fan If the hob is installed above a cupboard with doors a separator panel must be installed underneath it Leave a gap of at least 10 mm between the bottom of the hob and the surface of the panel which must be easily removable to allow sufficient access for any servicing procedures 21 X Instructions for the Installer 2 2 Fitting the gasket Fit the insulating gasket provided carefully around the outside edge of the hole made in the top as shown below pressing it down with your hands so that its entire surface fits snugly Follow the dimensions shown bearing in mind that the long front edge must be flush with the hole 76 mm 76 mm WwW OL 2 3 Fixing using brackets Fix the hob to the C S structure u
10. oints a V d 3 During reassembly after putting the hob skin in position press down on the points shown above to snap all the connections back into place 25 Sa y Instructions for the installer 5 2 Adjusting for bottled gas Undo the screw C and push the air regulator D fully down Remove the nozzle E with a 7 mm spanner and fit the suitable one following the instructions in the tables referring to the type of gas to be used The nozzle must not be tightened with a torque of more than 3 Nm Regulate the air flow by sliding the regulator D along until the distance X stated in point O Adjusting the primary air flow is obtained Fix the regulator D by tightening the screw C Rated Burner heat Bottled gas G30 G31 30 37 mbar capacity kW Nozzle By pass Reduced Flow Flow diameter mm heat rate g h rate g h 1 100 mm 1 100 capacity G30 G31 W Auxiliary 1 05 48 30 400 76 75 Semi rapid 1 7 62 32 450 124 121 Rapid 3 0 82 50 1050 218 214 Ultra Rapid 4 2 98 63 1600 305 300 26 Instructions for the Installer xX 5 3 Adjusting for natural gas The appliance is tested with G20 2H natural gas at the pressure of 20 mbar To return the appliance to the condition required to use this type of gas proceed as described in point 5 2 Adjusting for bottled gas but select the nozzles and adjust the primary air flow for natural gas as indicated in the table below and in point 5 4 Adjusting the
11. ons for the User 7 2 Lighting burners with safety device The burner it controls is shown next to each knob the example here shows the front left hand burner The appliance is equipped with electronic ignition Simply press the knob and turn it anti clockwise to the minimum flame symbol until the burner lights Keep the knob pressed down for about 2 seconds to keep the flame alight and prime the safety device The burner may go out when the knob is released In this case repeat the operation keeping the knob pressed down for longer When the burner has lit its control knob will light up to confirm that it is in operation The knob will go out a few seconds after it is turned to the O position or if the burner goes out accidentally The knob light comes on and goes out gradually If the burners should go out accidentally the safety device will be tripped about 20 seconds later cutting off the gas supply even if the gas tap is open 7 3 Practical hints for using the burners For better burner efficiency and to minimise gas consumption use flat even bottomed pans with lids of suitable size for the burner see point 7 4 Pan diameters ie When cooking to prevent burns or damage to the hob all pans or griddle plates must be placed inside the perimeter of the hob and must be at least 5 7 cm from the knobs 5 7 cm py Instructions for the User we ED 7 4 Pan diameters BURNERS min an
12. primary air flow Burner EN Natural gas G20 20 mbar Nozzle diameter Reduced heat capacity 1 100 mm W Auxiliary 1 05 73 400 Semi rapid UEA 92 450 Rapid 3 0 123 1050 Ultra Rapid 4 2 150 1400 5 4 Adjusting the primary air flow Refers to the gap X in mm PODRES ane Buea Auxiliary 0 5 3 Semi rapid 0 5 2 Rapid 2 3 Ultra Rapid 4 10 To identify the burners on your hob refer to the drawings in point 5 8 Hob burner layout 27 Instructions for the Installer 5 5 Reassembling the hob skin Reverse the procedure described in point 5 1 Removing the hob skin Fit the pan stands as described in point 7 1 Fitting the Pan Stands 5 6 Adjusting the minimum for natural gas Reassemble the components on the burner and fit the knobs onto the tap rods Light the burner and turn it to the minimum setting Remove the knob again and adjust the regulator screw inside or beside the tap rod depending on the model until an even minimum flame is obtained Put the knob back in place and check the stability of the burner flame the flame must not go out when the knob is turned quickly from the maximum to the minimum setting 5 7 Adjusting the minimum for bottled gas To adjust the minimum level when using bottled gas the adjuster screw inside or beside the tap rod must be turned fully clockwise depending on the models The diameters of the bypasses for each individual burner are stated in point 5
13. r similar cable resistant to a temperature of up to 90 C The cable must be replaced by a qualified electrician who must make the mains connection as shown below _ ann 20 mm L brown N blue 2 yellow green The power supply lead must be replaced by an authorised service centre to prevent all risks The manufacturer declines all responsibility for injury or damage caused by failure to comply with the above regulations or deriving from tampering with even just one part of the appliance 23 X 24 Instructions for the installer 4 Gas connection If the appliance is installed above an oven the gas hose must be passed around the back of the oven to prevent overheating The connection to the gas mains may be made using a copper pipe or a continuous wall steel hose in accordance with the relevant regulations To simplify connection the horizontal position of the fitting A on the back of the appliance is adjustable Undo the hexagonal nut B turn the fitting A into the required position and re tighten the hexagonal nut B it has a rubber gasket to ensure it provides an effective seal When installation is complete check for any leaks with a soapy solution never with a naked light The appliance is tested with G20 2H natural gas at the pressure of 20 mbar For use with other types of gas see section 5 Adapting to different types of gas The gas intake connection has an external
14. ses in particular a window should be opened or the speed of any fans increased after prolonged use 4 3 Combustion gas discharge Combustion gases must be discharged by means of hoods connected to a flue with reliable natural draught or a fan extraction system An effective extraction system requires careful design by an authorised specialist and must comply with the regulation distances and positions After installation the engineer must issue a certificate of compliance Instructions for the Installer xX 5 Adapting to different types of gas The operations described below must be carried out with the appliance not connected to the gas supply The appliance is tested with G20 2H natural gas at the pressure of 20 mbar If it is to be used with other types of gas the burner nozzles have to be changed and the primary air flow adjusted To replace the nozzles and adjust the burners the hob skin has to be removed Proceed as described below 5 1 Removing the hob skin 6 Remove all the burner M components in the numerical x ww order shown below A oO E e Pull off all the knobs Y gt ie e Lift all the burner A o T components off the hob N 1 e Remove the hob skin fixing screws 2 e After removing all the wa components described Qo above lift off the hob po skin Release all snap a o connections _ simultaneously the hob j is connected to the a OON a S casing underneath in 5 a N Ma p
15. sing the brackets A provided Carefully trim off the excess edge of the gasket B The dimensions in the drawing below refer to C the hole on the inside edge of the gasket See right for the precise holes to be used when B securing the hob to the J L___ top correctly using the p brackets 22 CE gt gt Instructions for the Installer X 3 Electrical connection Check that the power supply line voltage and size are as specified on the nameplate underneath the appliance s casing This nameplate must never be removed The plug on the end of the power supply lead and the wall socket must be of the same type and comply with the relevant regulations Check that the power supply line is properly earthed Pass the power supply cable through the rear of the cabinet taking care that it does not touch the bottom case of the hob or the oven if any built in underneath it The appliance s power supply line must be fitted with an omnipolar breaking device with contact gap of at least 3 mm located in an easily accessible position close to the appliance itself The use of reductions adapters or junctions is not recommended If the power supply cable has to be replaced the gauge of the wires in the new cable must be at least 0 75 mm 3 x 0 75 cable bearing in mind that the earth wire yellow green must be at least 20 mm longer at the end for connection to the appliance Use only a type HO5V2V2 F o
Download Pdf Manuals
Related Search