Smeg P662-1 hob
Contents
1. OF THE COOKING HOB WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE COOKING HOB INSTALLATION MUST BE CARRIED OUT BY QUALIFIED PERSONNEL IN ACCORDANCE WITH THE REGULATIONS IN FORCE THIS APPLIANCE IS INTENDED FOR DOMESTIC USES AND CONFORMS TO CURRENT REGULATIONS IN FORCE THE APPLIANCE HAS BEEN BUILT TO CARRY OUT THE FOLLOWING FUNCTIONS COOKING AND HEATING UP OF FOOD ALL OTHER USES ARE CONSIDERED IMPROPER THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR IMPROPER USE NEVER USE THIS APPLIANCE FOR HEATING ROOMS DO NOT LEAVE THE PACKING IN THE HOME ENVIRONMENT SEPARATE THE VARIOUS WASTE MATERIALS AND TAKE THEM TO THE NEAREST SPECIAL GARBAGE COLLECTION CENTRE THIS APPLIANCE IS MARKED ACCORDING TO THE EUROPEAN DIRECTIVE 2002 96 EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT WEEE THIS GUIDELINE IS THE FRAME OF A EUROPEAN WIDE VALIDITY OF RETURN AND RECYCLING ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT THE IDENTIFICATION PLATE WITH TECHNICAL DATA SERIAL NUMBER AND MARKING IS CLEARLY VISIBLE UNDER THE CASING THE PLATE ON THE CASING MUST NOT BE REMOVED TAKE CARE NOT TO SPILL SUGAR OR SWEET MIXTURES ON TO THE COOKING HOB WHEN HOT NEVER PLACE MATERIALS OR SUBSTANCES WHICH MAY MELT PLASTIC OR ALUMINIUM FOIL ON TO THE COOKING HOB IN THE EVENT PROMPTLY SWITCH OFF AND REMOVE THE MOLTEN MATERIAL WITH THE SCRAPER PROVIDED WHILE THE TOP IS STILL WARM TO PREVENT IT FROM BEING DAMAGED FAILURE TO INSTANTLY CL2. The bottom of the receptacles must be very thick and perfectly flat before placing on the cooking hob make sure that it as well as the cooking hob itself are perfectly clean and dry To avoid scratching of the cooking hob never use cast iron receptacles or receptacles with a rough bottom To avoid waste of energy make sure that the diameter of the receptacle bottom is the same as that of the circle marked on the cooking hob 27 28 ge I A Instructions for the user ome 8 CLEANING AND MAINTENANCE Before any intervention disconnect the power supply of the device 8 1 Cleaning the glazed ceramic hob The cooking hob should be regularly cleaned best after every use once the residual heat signal lamps have gone off Smudges from aluminium bottom pans can be easily cleaned off with a cloth dampened in vinegar Hemove any burnt residues after cooking with the scraper provided rinse with water and wipe dry with a clean cloth Regular use of the scraper considerably reduces the need for chemical detergents for the daily cleaning of the hob Never use abrasive or corrosive detergents e g cleaning powders oven sprays spot removers wire sponges 8 2 Cleaning stainless steel 8 2 1 Ordinary Daily Cleaning To clean and preserve the stainless steel surfaces always use only specific products that do not contain abrasives or chlorine based acids How to use pour the product on a damp cloth and wipe the surface
3. be cleaned After this switch on the cooking zones one after the other without pans for three minutes at the highest cooking setting This gets rid of the factory smell and evaporates any moisture which may have collected in the heating elements This is necessary to ensure that the electronic circuits operate correctly Remove all the removable label and any protective foils To switch on the hob follow the instructions provided in point 7 21 22 Instructions for the user ome 5 COOKING ZONES REAR LEFT HAND SINGLE PLATE REAR RIGHT HAND DUAL PLATE FRONT LEFT HAND DUAL PLATE FRONT RIGHT HAND SINGLE PLATE REAR RIGHT HAND OVAL PLATE CENTRAL OVAL PLATE FRONT LEFT HAND SINGLE PLATE SOOSONE 68 68 0 MSS 68 88 88 88 B8 The appliance features 4 5 cooking zones of different diameter and power Their position is clearly indicated by circles and the heat given off is defined by the markings on the glass surface The 5 cooking zones are of the HIGH LIGHT type and come on after a few seconds of being activated Heating intensity can be adjusted by means of the knobs located on the front panel from a minimum setting of 1 to a maximum setting of 6 9 Depending on models The cooking zones marked by two concentric circles O and by a circle fish kettle 0 CO feature double heating either within the inner circle or both circles Instructions for the user 6 DESCRIPTION OF CONTROL ON THE FRONT CONTROL P
4. rinse thoroughly and dry with a soft cloth or deerskin Do not use metallic sponges or sharp scrapers they will damage the surface P Use normal non abrasive products for steel and a wooden or plastic tool if necessary gt E Rinse thoroughly and dry with a soft cloth or deerskin Do not allow residues of sugary foods such as jam to set inside the oven If left to set for py too long they might damage the enamel lining of the oven d D NEVER USE A STEAM JET TO CLEAN THE APPLIANCE 9 SOMETHING WRONG PROBLEM POSSIBLE CAUSES WHAT TO DO The hob doesn t work The hob is not wired in or Switch on at the wall switch on at the wall There is a power failure Check power supply The results of cooking are Temperature is too high or Consult cooking tips unsatisfactory too low Wrong shelf position Wrong type of dish Cooking time is incorrect The hob smokes The hob is dirty Clean the hob once cooking is finished Let it cool first Food has spilled over Use a larger pan The plates do not come on Timed cooking programming Check the instruction for during timed cooking error timer The front panel will light up but DEMO mode is now Refer to paragraph 7 2 11 the plates will not switch on activated DEMO mode for how to deactivate DEMO mode A o A i o o o o a d Ew gt Instructions for the installer 10 INSTALLATION 10 1 Technical information Hob type See rating pl
5. ABLE HEAT PROOF GLOVES SHOULD BE WORN FOR ALL OPERATIONS BEFORE THE APPLIANCE IS PUT INTO OPERATION ALL THE LABELS AND PROTECTIVE FILMS APPLIED INSIDE OR OUTSIDE MUST BE REMOVED THE POWER LEAD MUST BE CHANGED BY THE MANUFACTURER OR BY AN AUTHORISED SERVICE CENTRE TO PREVENT ANY RISKS IMMEDIATELY AFTER INSTALLATION CARRY OUT A BRIEF INSPECTION TEST OF THE APPLIANCE FOLLOWING THE INSTRUCTIONS BELOW SHOULD THE APPLIANCE NOT FUNCTION DISCONNECT IT FROM THE SUPPLY AND CALL THE NEAREST TECHNICAL ASSISTANCE CENTRE NEVER ATTEMPT TO REPAIR THE APPLIANCE ALL REPAIRS MUST BE CARRIED OUT BY AN AUTHORISED ENGINEER OR AT AN AUTHORISED SERVICE CENTRE Important Beware of children in the vicinity as the signal lamps indicating residual heat are out of sight to them In fact even after having been turned off the cooking hob remains hot for a N certain period of time Make sure that children never touch the cooking hob E Instructions for the user 3 KNOW YOUR HOB Ceramic surface of the appliance Single plate Oval dual plate Circular dual plate Timer Display Cooking zones Control panel Plate power display OOH OoONs NOT ALL COMPONENTS DESCRIBED ARE PRESENT ON ALL MODELS 4 BEFORE FIRST USE Do not leave the packing in the home environment Separate the various waste materials and take them to the nearest special garbage collection centre Before cooking for the first time the hob has to
6. ANEL RI FRONT LEFT HAND PLATE CONTROL 2 REAR LEFT HAND PLATE CONTROL ZONE ZONE 3 REAR RIGHT HAND PLATE CONTROL 4 FRONT RIGHT HAND PLATE CONTROL ZONE ZONE 5 TIMER ZONE CENTRAL PLATE CONTROL ZONE 23 24 Instructions for the user ome 7 USE OF THE COOKING HOB 7 1 Hobs with knobs 7 1 1 Single plates Each knob shows the plate it is for 0 To heat turn the knob to the desired position 1 to 6 Adjustment is continuous so that the appliance also operates at any intermediate value 7 1 2 Dual plates Each knob shows the plate it is for 0 To heat the inner cooking zone turn the knob to the desired position 1 to 6 To heat both the inner and outer cooking zones turn the knob to and then release The knob will thus return to 9 To adjust heating intensity rotate the knob anticlockwise to the desired position To return to heating of the inner 5 2 cooking zone only set the knob back to O and then turn to the desired position 1 to 6 4 3 7 1 3 Description of symbols REAR LEFT REAR RIGHT gt FRONT LEFT m FRONT RIGHT 7 1 4 Residual heat The 4 signal lamps located between the cooking zones come on when the temperature of one or more of the heating zones exceeds 60 C The lamps go off upon temperature dropping to below approximately 60 C O O exo 7 1 5 Switching off To turn off return the knob to O Instructions for the user 7 2 Hobs with push buttons On first connection to t
7. EAN THE GLAZED CERAMIC HOB COULD LEAD TO ENCRUSTATIONS WHICH ARE IMPOSSIBLE TO REMOVE ONCE THE HOB HAS COOLED DOWN The manufacturer declines all responsibility for damage to persons or things caused by non observance of the above prescriptions or by interference with any part of the appliance or by the use of non original spares 19 20 Safety instruction 2 SAFETY INSTRUCTION INSTRUCTIONS FOR THE INSTALLER THESE ARE INTENDED FOR THE QUALIFIED TECHNICIAN WHO MUST INSTALL THE APPLIANCE SET IT FUNCTIONING AND CARRY OUT AN INSPECTION TEST IT IS OBLIGATORY FOR THE ELECTRICAL SYSTEM TO BE GROUNDED ACCORDING TO THE METHODS REQUIRED BY SAFETY RULES WHEN LINKING UP TO MAINS BY PLUG AND SOCKET MAKE SURE THAT BOTH ARE COMPATIBLE AND CONNECT BY MEANS OF A POWER CABLE COMPLYING WITH APPLICABLE REGULATIONS THE SOCKET MUST BE ACCESSIBLE AFTER THE APPLIANCE HAS BEEN BUILT IN NEVER UNPLUG BY PULLING ON THE CABLE ALWAYS CHECK THAT THE CONTROL ARE IN THE POSITION O OFF WHEN YOU FINISH USING THE HOB DURING USE THE APPLIANCE BECOMES VERY HOT TAKE CARE NOT TO TOUCH THE SURFACE OF THE HOB THE APPLIANCE IS NOT INTENDED FOR USE BY YOUNG CHILDREN OR INFIRM PERSONS WITHOUT SUPERVISION YOUNG CHILDREN SHOULD BE SUPERVISED TO ENSURE THAT THEY DO NOT PLAY WITH THE APPLIANCE WARNING IF THE SURFACE IS CRACKED SWITCH OFF THE APPLIANCE TO AVOID THE POSSIBILITY OF AN ELECTRIC SHOCK THE APPLIANCE BECOMES VERY HOT DURING USE SUIT
8. IT POWER LINE WITH AN OMNIPOLAR CIRCUIT BREAKER WITH A CONTACT OPENING GAP EQUAL TO OR GREATER THAN 3 MM IN AN EASILY ACCESSIBLE POSITION IN PROXIMITY TO THE OVEN 29 Instructions for the installer For operation on 380 415 V 3N use a HObRRF HO5RN F type five 380 415V 3N 1 5 mm core cable 5 x 1 5 mn e This type of connection cannot be used for models with 5 plates E 20 mm For operation on 380 415 V 2N use a HO5HH F HO5HN F type 380 415V 2N 2 5 mm four core cable 4 x 2 5 mn Es Es 20 mm 220 240V 3 mv For operation on 220 240 V 3 use a HObBHH F HO5HRHN F type four core cable 4 x 2 5 mm a 20 mm For operation on 220 240 V use a HO5RR F HO5HN F type three 220 240V core cable 4mm 3 x 2 5 mm cooking hob with 4 plates 3 x 4 mm cooking hob with 5 plates The cable end to be connected to the appliance must be provided with an earth wire yellow green at least 20 mm longer Head the connection layout plate underneath the appliance with care If the appliance you have purchased is not fitted with a mains power lead a power lead resistant to a temperature of at least 90 C must be used Otherwise the electrical safety of the appliance may be put at risk The manufacturer declines all responsibility for damage to persons or things caused by non observance of the above prescriptions or by interference with any part of the appliance Warni
9. N OD QA KR WD a 9o Contents INSTRUCTIONS FOR PROPER USE SAFETY INSTRUCTION KNOW YOUR HOB BEFORE FIRST USE COOKING ZONES DESCRIPTION OF CONTROL ON THE FRONT CONTROL PANEL USE OF THE COOKING HOB CLEANING AND MAINTENANCE SOMETHING WRONG 10 INSTALLATION 18 correct procedures for cleaning and maintenance of the appliance install the appliance set it functioning and carry out an inspection test Further information about the products can be found at www smeg com 19 20 21 21 22 23 24 28 28 29 INSTRUCTIONS FOR THE USER these contain user advice description of the commands and the INSTRUCTIONS FOR THE INSTALLER these are intended for the qualified technician who must N A ld AN Instructions for proper use 1 INSTRUCTIONS FOR PROPER USE ELECTRICAL CONNECTION PLEASE REFER TO INSTALLATION INSTRUCTION FOR THE GAS amp ELECTRICAL SAFETY REGULATIONS AND THE VENTILATION REQUIREMENTS IN YOUR OWN INTEREST AND THAT OF SAFETY IT IS THE LAW THAT ALL GAS AND ELCTRICAL APPLIANCES BE INSTALLED AND SERVICE BY COMPETENT PERSONS WHO WILL COMPLY WITH THE RELEVANT STANDARDS AND REGULATIONS CORGI REGISTERED INSTALLERS UNDERTAKE TO WORK TO SATISFCTIORY STANDARDS DISCONNECTION OF GAS AND ELECTRIC APPLIANCES SHOULD ALWAYS BE CARRIED OUT BY COMPETENT PERSON THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE
10. ate Electrical connections 220 240V 50 60Hz 380 415V 2N 50 60Hz 380 415V 3N 50 60Hz HOB RATING Electric Maximum electrical power See rating plate DIMENSION OF THE HOB Width mm 720 588 Depth mm 510 510 10 2 The rating plate Make sure that the voltage and capacity of the power line conform to the data shown on the plate located LCF under the casing Do not remove this plate for any JT 55 M reason 220 240 380 415V 3N 50 60Hz CE Serial ENEY MODEL AN moa EA 10 3 Electrical connection IT IS OBLIGATORY FOR THE ELECTRICAL SYSTEM TO BE GROUNDED ACCORDING TO THE METHODS REQUIRED BY SAFETY RULES WHEN LINKING UP TO MAINS BY PLUG AND SOCKET MAKE SURE THAT BOTH ARE COMPATIBLE AND CONNECT BY MEANS OF A POWER CABLE COMPLYING WITH APPLICABLE REGULATIONS THE SOCKET MUST BE ACCESSIBLE AFTER THE APPLIANCE HAS BEEN BUILT IN NEVER UNPLUG BY PULLING ON THE CABLE IMMEDIATELY AFTER INSTALLATION CARRY OUT A BRIEF INSPECTION TEST OF THE HOB FOLLOWING THE INSTRUCTIONS IF THE HOB FAILS TO OPERATE AFTER CHECKING THAT YOU HAVE CARRIED OUT THE INSTRUCTIONS CORRECTLY DISCONNECT THE APPLIANCE FROM THE ELECTRICAL MAINS AND CONTACT YOUR NEAREST SERVICE CENTRE NEVER ATTEMPT TO REPAIR THE APPLIANCE IF A PLUG AND SOCKET CONNECTION IS BEING USED MAKE SURE THAT THE PLUG AND SOCKET ARE COMPATIBLE AVOID USE OF ADAPTERS AND SHUNTS AS THESE COULD CAUSE OVERHEATING AND RISK OF BURNS IF A FIXED CONNECTION IS BEING USED F
11. e is set on O the hob will switch off automatically If the plates are hot 5 seconds after the switch off the H appears warning of the residual heat 7 2 11 DEMO mode Some models have a DEMO function not normally enabled which deactivates the plates If however you are experiencing problems the following keystroke sequence to be executed within 60 seconds of switching on the hob will deactivate DEMO mode Press the leftmost key 4 one time then the third key from the left L two times and finally the second key from the left three times x1 x2 J K k X3 7 3 Cooking tips The table below shows the power values which can be set with the relative type of food alongside Setting may vary depending on the amount of food and personal taste KNOB NUMBER ON TYPE OF FOOD SETTING THE DISPLAY 1 1 To melt butter chocolate and the like To heat food keep small amounts of water on the boil and whip up end sauces with egg yolk or butter To heat solid or liquid food keep small amounts of water on the 3 4 5 boil thaw deep frozen food cook omelettes of 2 or 3 eggs fruit and vegetables and the like To stew meat fish and vegetables simmer food make jams and 4 6 SO On 5 7 8 To roast meat fish steaks and liver to saut meat fish eggs and SO On 6 9 To deep fry potatoes etc and to quick boil water For best results and energy saving only use receptacles suitable for electric cooking
12. essed for 2 3 second 7 2 4 Plate layout O REAR LEFT O REAR RIGHT Q MIDDLE Q FRONT LEFT FRONT RIGHT 7 2 5 Timer on some models only Some models are equipped with cooking timer To activate the timer proceed as follows with the plates on or off 1 keep the symbol pressed for a few seconds the two displays in the middle of the screen printing will switch on showing a flashing figure 30 if the plate is on the power display value will drop by one point but it will return to the previous value at once 2 press the or symbols to increase or reduce the cooking time and set it on the number of minutes required the number of minutes flashes 3 seconds after the last key is pressed the minutes display will stop flashing and the figure O on the power display will start to flash 4 The power level must be set within another 5 seconds as described in points 7 2 1 7 2 2 otherwise the hob will switch off automatically If the power is not adjusted within 5 seconds the timer will still start the count 5 Timed cooking will start 5 seconds after the last power adjustment At the end of the time set 3 BEEPS will sound in sequence they are repeated 5 times at 5 second intervals To stop the beeps in manual mode simply press the or symbol of any push button 7 2 6 Modifying the data set During timed cooking each single pressure on the L or symbols increases or reduces the power of the plate 5 seconds after the
13. et provided all around the outer edge of the hole in the top surface as shown in the figures below pressing it down so as to make it adhere properly For measurements refer to the figure depending on the hob model to be installed bearing in mind that in both models the front and rear sides must skim the hole Secure the hob to the counter with brackets A supplied Carefully trim any excess from border B of the gasket The distances in the following drawing refer to the hole on the inner side of the gasket 53 mm 53 mm Accurately position the gasket provided all around the outer edge of the hole in the top surface as shown in the figures below pressing it down so as to make it adhere properly Refer to the dimensions shown in the diagram bearing in mind that the sides A must be flush with the hole Fix the hob to the unit using the brackets B provided Carefully trim any excess from border C of the gasket The distances in the following drawing refer to the hole on the inner side of the gasket 31 32 Instructions for the installer When fixing the hob to the cabinet use only the holes provided illustrated here This appliance must not be built in above a dishwasher Installation of an oven without cooling fan underneath the hob is forbidden Pass the power supply cable through the back of the unit taking care that it does not touch the bottom casing of
14. he electrical mains an operating check will be carried out automatically and all the indicator lights will come on for a few seconds 7 2 1 Single plates When not in use all hob components will be switched off If the symbol of any push button is pressed for a few seconds the hob will switch on and the circular sectors on the buttons indicating the plate controlled by each button will illuminate The power level must be set within 30 seconds after the sectors light up otherwise the hob will switch off automatically To set the power level use the L or push buttons as follows 1 press the 4 0 appears on the display meaning that the plate has been switched on 2 press the 9 appears on the display meaning that the plate is on at full power 3 Atthis point a Pressing the symbol repeatedly regulates the plate s power setting from the full power level 9 towards the lowest setting 1 b Pressing the L symbol repeatedly regulates the plate s power setting from the lowest power level 1 to the highest setting 9 4 To switch off the plate return the display reading to O by pressing the or 4 symbol repeatedly A BEEP of confirmation is heard whenever the or symbols are pressed 7 2 2 Dual plates Operation of plates with dual heating is different from that of those with single heating When they are switched on two indicator lights illuminate beside the number showing the power level as shown in the diagram When
15. last button is pressed a BEEP will sound and the display showing the time left will start flashing The L or symbols can now be pressed to increase or decrease the cooking time A few seconds after the last cooking time adjustment the minutes display will also stop flashing and the count will restart with the new settings 7 2 7 Residual heat Each plate is equipped with a residual heat warning device After any plate is switched off a flashing X9 may appear on the display This warns that the cooking zone concerned is still very hot Cooking can be restarted while the is flashing proceed as described in points 7 2 1 7 2 2 7 2 8 Control circuit board thermal protection If the plates overheat the internal electronics board the heat will be switched off automatically This switches off power to the front plates and the letters and flash alternately on the power leds If the electronics board does not cool down power to all the plates is switched off and the power leds display the text Cooking can be resumed once the temperature has dropped below the safety threshold 7 2 9 Operator Error If the user makes a mistake when using the push buttons an appears on the power display it will remain there as long as the user continues to press the button being used incorrectly Instructions for the user eese 7 2 10 Switching off The hob switches off when all the displays read O About 30 seconds after the last plat
16. ng pass the power cable through hole A and fit TYPE 1 TERMINAL BOARD the cable clamp plate after making the electrical connection To fit the plate simply use the provided bolts to secure it under the casing as shown in the figure Warning close the cable clamp after making the electrical connection Close the terminal board cover by twisting it down in top of supporti ng unit 560 mm Hole Hole in top of supporti ng unit 685mm Instructions for the installer 10 4 Positioning of the hob The following operation requires building and or carpentry work so must be carried out by a competent tradesman Installation can be carried out on various materials such as masonry metal solid wood or plastic laminated wood as long as they are heat resistant T 90 C Create an opening with the dimensions shown in the figure in the top surface of the counter keeping a minimum distance of 50 mm from the rear border This appliance can be mounted against walls higher than the work surface on condition that a certain distance UK be kept between the appliance and the wall as shown in the figure so as to avoid damage from overheating Make sure there is a minimum of 750 mm between the hob and any shelf that may be installed directly above them The only model requiring a hole of 685 mm in the top of the supporting unit is the model with 5 cooking zones and central fish plate Accurately position the gask
17. not in use all hob components will be switched off If the symbol of any push button is pressed for a few seconds the hob will switch on and the circular sectors on the buttons indicating the plate controlled by each button will illuminate The power level must be set within 30 seconds after the sectors light up otherwise the hob will switch off automatically To set the power level use the 4 or push buttons as follows 1 press the symbol 0 appears on the display meaning that the plate is on at full power 2 press the L symbol again 9 appears on the display meaning that the small plate is on at full power 3 here are now two options available a press the symbol once two markers illuminate beside the 9 press the symbol to set the power of the dual plate or b e after proceeding as described in point 2 press the the symbol repeatedly to set the power of the small plate 4 To switch off the plate return the display reading to O by pressing the symbol repeatedly 25 26 Instructions for the user ome 7 2 3 Plate lock out 20 seconds after the last power adjustment the plate switches to lock out status and no more adjustments to the power levels set will be possible This function indicated by a dot which appears alongside the power level see side is provided to ensure greater safety in use of the hob The lock out can be eliminated by keeping the 4 or symbol of any push button pr
18. the hob or the oven if any installed underneath it 100 mm IMPORTANT when installing the appliance above a cupboard a dividing shelf as shown above must be installed If installed above an under bench oven this is not required Installation of an oven without cooking fan underneath the hob is forbidden
Download Pdf Manuals
Related Search