De Dietrich DHD792X cooker hood
Contents
1. be sufficiently ventilated when the kitchen hood is used together with other gas combustion devices or other fuels The suctioned air must not be conveyed into a conduit used for the disposal of the fumes generated by appliances that combust gases or other fuels The flaming of foods beneath the hood itself is severely prohibited The use of exposed flames is detrimental to the filters and may cause a fire risk and must therefore be avoided in all circumstances Any frying must be done with care in order to make sure that the oil does not overheat and burst into flames As regards the technical and safety measures to be adopted for fume discharging it is important to closely follow the relations provided by the competent authorities The hood must be regularly cleaned on both the inside and outside AT LEAST ONCE A MONTH it is in any event necessary to proceed in accordance with the maintenance instructions provided in this manual Failure to follow the instructions as concerns hood and filter cleaning will lead to the risk of fires Do not use or leave the hood without the lamp correctly mounted because of the possible risk of electric shocks We decline any responsibility for any problems damage or fires caused to the appliance as the result of the non observance of the instructions included in this manual Installation The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part o2. not included they need to be bought for the fume discharge to the connection ring placed on top of the extractor motor unit The other end of the tube should be connected to a fume expulsion device towards the outside in case the hood is used in extractor version Fix the upper cover with 3 screws 12 Note this is supplied already mounted in some cases Only for chimney installation In case you want to use the hood in filtering version fasten the deflector F to the support bracket and connect the other side of the tube to the connection ring placed on the deflector 13 Apply the chimneys and fasten them on with two screws 14a to the chimney support bracket G 14b and make the lower part of the chimney slide into the suited part on top of the chimney Mountthe grease filters and close the vapour scheme Warning If the hood has to be used in extractor version remove if supplied the carbon filter and the fastening wand placed on the back of the grease filters see relative paragraph If the hood has to be used in filtering version make sure that the carbon filter is already mounted on the back of the grease filter or in case it s missing buy it and install it Note only for installation without chimneys In case you want to use the hood in filtering version install the grille deflector instead of the flange 10b Operation To selectthe functions of the hood just touch the commands XE v L
3. the panel is fixed in its place well Grease filter Fig 2 This must be cleaned once a month or when the filter saturation indication system if envisaged on the model in possession indicates this necessity using non aggressive detergents either by hand or in the dishwasher which must be setto a low temperature and a short cycle When washed in a dishwasher the grease filter may discolour slightly but this does not affect its filtering capacity To remove the grease filter pull the spring release handle Charcoal filter filter version only Fig 3 It absorbs unpleasant odours caused by cooking The charcoal filter can be washed once every two months or when the filter saturation indication system if envisaged on the model in possession indicates this necessity using hot water and a suitable detergent or in a dishwasher at 65 C if the dishwasher is used select the full cycle function and leave dishes out Eliminate excess water without damaging the filter then put it in the oven for 10 minutes at 100 C to dry completely Replace the mattress every 3 years and when the cloth is damaged Montage Open the steam screen and remove the grease filter Install the carbon filter on the back of the grease filter and fix with two rods Attention The rods are included in the carbon filter packing and not on the hood dismantle the filter act in the reverse manner CLEANING AND UPKEEP OF YOUR APPLIANCE
4. FR Prescriptions de montage et mode d emploi CS N vod na montaz a pouzivani DA Bruger og monteringsvejledning DE Montage und Gebrauchsanweisung EL OAHFIEZ ZYNAPMOAOTHEHZ XPH2H2 EN Instruction on mounting and use ES Montaje y modo de empleo HU Felszerel si s haszn lati utasit s IT Istruzioni di montaggio e d uso NL Montagevoorschriften en gebruiksaanwijzingen PL Instrukcja montazu i obstugi PT Instrug es para montagem e utilizac o SK N vod k mont zi a uziti SV Monterings och bruksanvisningar Hotte aspirante Digestor Emhatte Dunstabzugshaube Cooker Hood Campana extractora Konyhai p raelsz v Cappa aspirante Afzuigkap Okap kuchenny Exaustor Ods vac pary K ksfl kt OPTION OPTION XN co ado X x De Dietrich Dear Customer You have just acquired a DE DIETRICH hood and we would like to thank you Our research teams have created this new generation of appliances for you Their quality design features and technological advances make them exceptional products and reveal our unique know how Your new DE DIETRICH hood will blend harmoniously into your kitchen and will perfectly combine extraction performance and ease of use We wanted to offer you a product of excellence In the DE DIETRICH product range you will also find a wide choice of hobs ovens microwaves dishwashers cookers fridges freezers that you can coordinate with
5. GruppoBrandt_pr Ed 08 07
6. To keep your appliance in good working order recommend that you use Clearit household products Clearit offers you professional products and adapted solutions for the daily upkeep of your household and kitchen appliances You may find them in conventional retail outlets along with a complete line of by products and consumables we Professional for the general public expertise Replacing lamps Fig 4 Disconnect the hood from the electricity Warning Prior to touching the light bulbs ensure they are cooled down 1 Using a flat head screwdriver or equivalent tool carefully pry loose the light cover 2 Remove the damaged light and replace with a new 12 Volt 20 Watt Maximum halogen light made for a G 4 base SUITABLE FOR USE IN OPEN LUMINAIRES Follow package directions and do not touch new light with bare hands 3 Reinstall the light cover it will snap shut If the lights do not work make sure that the lamps are fitted properly into their housings before you call for technical assistance This appliance is marked according to the European directive 2002 96 EC on Waste Electrical and Electronic Equipment WEEE By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The symbol mmm on the product or on the documents accompanying the product i
7. asons that there is no other supplied material inside the hood e g packets with screws guarantees etc eventually removing them and keeping them f possible disconnect and move freestanding or slide in range from cabinet opening to provide easier access to rear wall ceiling Otherwise put a thick protective covering over countertop cooktop or range to protect from damage and debris Select a flat surface for assembling the unit Cover that surface with a protective covering and place all canopy hood parts and hardware in it e Disconnect the hood during electrical connection by turning the home mains switch off In addition check whether near the installation area of the hood in the area accessible also with the hood mounted an electric socket is available and it is possible to connect a fumes discharge device to the outside only suction version e Carry out all the masonry work necessary e g installation of an electric socket and or a hole for the passage of the discharge tube Expansion wall plugs are provided to secure the hood to most types of walls ceilings However a qualified technician must verify suitability of the materials in accordance with the type of wall ceiling The wall ceiling must be strong enough to take the weight of the hood Do not tile grout or silicone this appliance to the wall Surface mounting only 35 An aesthetic flue can be purchased as an optional accessory Check with the
8. assistance centre whether the model in your possession envisages this possibility We advise installing the hood after having purchased the flue to check with certainty the most suitable installation e Trace a central line on the wall in order to ease mounting 1 position the hole template in a way that the middle line printed on top corresponds to the central line marked previously and the lower side of the mask corresponds to the lower part of the hood once mounted 2 Make 3 holes 8 mm with a drill and fix the support bracket with two dowels and screws to the wall 3 insert the third dowel into the lower hole e Only for chimney installation Apply the support bracket G to the adherent ceiling use the chimney support bracket as a hole scheme if present the small eyelet found on the support should coincide with the line previously traced on the wall and trace with a pencil 2 holes drill the holes 8mm insert 2 plugs Fasten the support bracket to the wall with 2 5x45mm screws 4 Open the vapour scheme and remove the grease filters see relevant paragraph Hang the hood 5 regulate the position 6 7 and fasten it securely with one screw and washer 8 Carry out electrical connections 9 but leave the hood disconnected from the general electrical main panel Install the flange supplied on the exit hole of the hood 10a Carry out the connection of one tube 11 tube and ties for fastening
9. d for whoever installs or uses it This apparatus has been created to be installed in a kitchen and for normal domestic use Do not use it for commercial or industrial purposes or other purposes for which it was not created Do not modify or try to modify the characteristics of this apparatus It would be dangerous for you 34 Using over a fuel wood carbon cooking top is not authorised If the filtering hood is installed in a kitchen heated by an apparatus connected to a fireplace e g a stove the filtering version of the hood must be installed Do not use the hood without fat filters Do not use steam or pressure cleaning equipment on your apparatus for reasons of electrical safety WARNING Do not connect the appliance to the mains until the installation is fully complete Before any cleaning or maintenance operation disconnect the hood from the mains by removing the plug or disconnecting the home mains switch The appliance is not intended for use by children or persons with impaired physical sensorial or mental faculties or if lacking in experience or know how unless they are under supervision or have been trained in the use of the appliance by a person responsible for their safety Children should be monitored to ensure that they do not play with the appliance Never use the hood without effectively mounted grating The hood must NEVER be used as a support surface unless specifically indicated The premises must
10. eclined Note the elements marked with the symbol 9 are optional accessories supplied only with some models or elements to purchase not supplied Use The hood is designed to be used either for exhausting or filter version Ducting version The hood is equipped with a top air outlet B for discharge of fumes to the outside exhaust pipe and pipe fixing clamps not provided Fig 5 6 Attention If the hood is supplied with carbon filter then it must be removed Filter version Should it not be possible to discharge cooking fumes and vapour to the outside the hood can be used in the filter version fitting an activated carbon filter and the deflector F on the support bracket G fumes and vapours are recycled through the top grille H by means of an exhaust pipe connected to the top air outlet B and the connection ring mounted on the deflector F exhaust pipe and pipe fixing clamps not provided Fig 5 6 Attention If the hood is not supplied with carbon filter then it must be ordered and mounted Description of the hood Fig 1 1 Control panel 2 Grease filter 3 Grease filter release handle 4 Halogen lamp 5 Perimeter suction panel Caution Keep this use manual with your apparatus If the apparatus has to be sold ceded to someone else make sure that this manual is also sent Read this manual carefully before installing or using your apparatus because it contains important information for your safety an
11. f the range hood must be not less than 45cm from electric cookers and 65cm from gas or mixed cookers If the instructions for installation for the gas hob specify a greater distance this must be adhered to N Electrical connection The mains power supply must correspond to the rating indicated on the plate situated inside the hood If provided with a plug connect the hood to a socket in compliance with current regulations and positioned in an accessible area If it not fitted with a plug direct mains connection or if the plug is not located in an accessible area apply a bi polar switch in accordance with standards which assures the complete disconnection of the mains under conditions relating to over current category Ill in accordance with installation instructions Warning Before re connecting the hood circuit to the mains supply and checking the efficient function always check that the mains cable is correctly assembled Mounting Fig 5 6 Before beginning installation e Check that the product purchased is of a suitable size for the chosen installation area e facilitate installation remove the fat filters and the other parts allowed and described here dismantle and mount it To remove see also the relative paragraphs Remove the active carbon filter s if supplied see also relative paragraph This these is are to be mounted only if you wantlo use the hood in the filtering version e Check for transport re
12. ight key ON OFF Fio Intensive speed selection key suction Booer power duration 5 minutes press again to 77 return to previous setting High speed selection key suction power Medium speed selection key suction power when flashing it indicates the need to wash or replace the carbon filter This signal is normally deactivated Press keys 1 and 2 at the same time to activate it At first only key 1 will flash and then both keys 1 and 2 to indicate activation Repeat the operation to deactivate the signal At first keys 1 and 2 will flash and then only key 1 to indicate deactivation 2 us prs ON LJ d m Low speed selection key suction power when flashing it indicates the need to wash the fats filter au Motor key OFF stand by excludes the electronics reset wash replace filters signals MOTOR OFF Press briefly to switch the motor off RESET FILTERS SIGNALS After having carried out maintenance of the filters press the key for 3 seconds Flashing led 1 fats filter or 2 carbon filter will stop flashing EXCLUDING THE ELECTRONICS Press the key for 3 seconds The hood command electronics will be excluded This function can be useful during the product cleaning operations Just repeat the operation to reinsert the electronics i A If the hood fails to operate correctly briefly disconnect it from the mains power supply for almost 5 sec by pull
13. ing out the plug Then plug it in again and try once more before contacting the Technical Assistance Service Maintenance ATTENTION Before performing any maintenance operation isolate the hood from the electrical supply by switching off at the connector and removing the connector fuse Or if the appliance has been connected through a plug and socket then the plug must be removed from the socket 36 Cleaning The cooker hood should be cleaned regularly at least with the same frequency with which you carry out maintenance of the fat filters internally and externally Clean using the cloth dampened with neutral liquid detergent Do not use abrasive products DO NOT USE ALCOHOL Warning Failure to carry outthe basic cleaning recommendations of the cooker hood and replacement of the filters may cause fire risks Therefore we recommend oserving these instructions The manufacturer declines all responsibility for any damage to the motor or any fire damage linked to inappropriate maintenance or failure to observe the above safety recommendations Maintenance of the panel Dismantling Extract with decision LOWER SIDE and rotate upwards Cleaning the panel should be cleaned with the same frequency as the fat filters using a cloth soaked in neutral liquid detergents Avoid the use of products containing abrasives DO NOT USE ALCOHOL Montage Proceed in the reverse direction for dismantling Attention Always check that
14. ndicates that this appliance may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment Disposal must be carried out in accordance with local environmental regulations for waste disposal For more detailed information about treatment recovery and recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product 3 Troubleshooting SYMPTOMS SOLUTIONS Ensure that The power is not cut off speed has been selected The hood is not working Ensure that The selected motor speed is sufficient for the quantity of smoke and vapours to be Cleared The kitchen is sufficiently ventilated to allow for fresh air intake The carbon filter is not worn hood operating in recycling mode The hood is not operating effectively Ensure that The power is not cut off The single pole cut off device was not activated The hood stopped working After sales service Any maintenance on your equipment should be undertaken by either your dealer or another qualified mechanic who is an authorized agent for the brand appliances When making an appointment state the full reference of your equipment model type and serialnumber This information appears on the manufacturers nameplate attached to your equipment
15. your new DE DIETRICH hood Visit our website www dedietrich electromenager com where you will find our latest innovations as well as useful and complementary information DE DIETRICH Setting New Values As part of our commitment to constantly improving our products we reserve the right to make changes to them based on technical advances to their technical and functional features and appearance VN warning Before installing and using your appliance please carefully read this Guide to Installation and Use which will allow you to quickly familiarise yourself with its operation www dedietrich electromenager com k Contents UK Instruction on mounting and 34 34 ASAS 34 UV ON 34 Installation A EET 34 Electrical COMP CCU OM E m mum 35 AP 35 jl Married 36 tii 36 E A CR T UU CT 36 Grease Emm 36 Charcoal filter filter version 36 o PE E e E PE 37 io PA 37 37 33 UK Instruction on mounting and use Consult the designs in the front pages referenced in the text by alphabet letters Closely follow the instructions set out in this manual All responsibility for any eventual inconveniences damages or fires caused by not complying with the instructions in this manual is d
Download Pdf Manuals
Related Search