Smeg FA550XBI2 side-by-side refrigerator
Contents
1. Duck goose 6 Cooked poultrv in sauce 6 Steak without sauce 25 DESCRIPTION OF THE APPLIANCE REFRIGERATOR COMPARTMENT ZZOART TIOMMUONDp N o Inside light Inside light Adjustable shelf Shelf drawer lid Crisper Crisper adjustment Meat vegetable drawer Meat vegetable drawer adjustment Dairy products compartment Door trays 2 litre door tray with bottle holder 0 75 litre door tray Water filter Multiflow depending on model O OG FREEZER COMPARTMENT O Automatic ice maker Glass shelves Racks depending on the model Q Drawer Bottom basket depending on the model R Drawer Top basket depending on the model 5 drawer T Freezer door travs U Inside light MULTIFLOW AIR DISTRIBUTION MULTIFLOW is a ventilated air distribution system which ensures a homogeneous temperature inside the refrigerator compartment Thanks to this system the different types of food can be stored on any of the shelves of the appliance Attention should be paid not to obstruct the air distribution vents thus ensuring free air circulation GUIDE TO THE INSIDE PARTS Removing and repositioning the refrigerator compartment and freezer shelves The shelves can be positioned as required The glass shelves are strong enough to hold bottles milk cartons and heavy food however take care not to bang products on the shelves To remov2. Operation problems are often due to minor causes that can be found and fixed without using anv tools Noises from the appliance are normal since the fans and compressors for controlling its operation switch on and off automaticallv Some noises can be reduced by e levelling the appliance and installing it on a flat surface separating and preventing contact of the appliance with the cabinets e making sure the inside parts are correctly positioned e making sure the bottles and containers are not touching each other Some possible operation noises e hissing when the appliance is switched on the first time or after a long period gurgling when the refrigerant enters the pipes e humming when the water valve or fan are activated e rattling when the compressor starts up or when the ice drips in the bucket e sudden thud when the compressor starts up or stops Ea M Hissss Brrrr S 9 35 TROUBLESHOOTING GUIDE The appliance does not work e Is the power cable plugged into a socket powered with the right voltage e Have you checked the protection devices and fuses of your home s electrical system The motor seems to run too much e Is the condenser free of dust and fluff e Are the doors properly closed e Are the door seals intact e hot days or when the room is warm it is normal for the motor to run longer e If the appliance door has been left open for a long time or if large amou
3. button marked with A in the figure to activate the anticondensate function Blown lamp Always unplug the appliance 2 Refer to chapter Maintenance and Cleaning 37 ELECTRICAL CONNECTION FOR GREAT BRITAIN AND IRELAND ONLV Warning this appliance must earthed Fuse replacement If the mains lead of this appliance is fitted with a BS 1363A lI 3amp fused plug to change fuse in this type of plug use A S T A approved fuse to BS 1362 type and proceed as follows 1 Remove the fuse cover A and fuse 2 Fit replacement fuse into fuse cover 3 Refit both into plug Important The fuse cover must be refitted when changing a fuse and if the fuse cover is lost the plug must not be used until a correct replacement is fitted Correct replacement are identified by the colour insert or the colour embossed in words on the base of the plug Replacement fuse covers are available from your local electrical store For the Republic of Ireland only The information given in respect of Great Britain will frequently apply but a third type of plug and socket is also used the 2 pin side earth type Socket outlet plug valid for both countries If the fitted plug is not suitable for your socket outlet please contact After sales Service for further instruction Please do not attempt to change plug yourself This procedure needs to be carried out by a qualified technician in compliance with the manuf
4. set ideal temperature is 18 C As soon as the freezer compartment reaches the required temperature it is automaticallv displaved To change the temperature press the C freezer button until the desired value is reached The selected temperature will start flashing and then come on permanentiv within 5 seconds on the displav Refrigerator temperature The factory set ideal temperature is 5 C To change the temperature press the refrigerator button until the desired value is reached The selected temperature will start flashing and then come on permanentiv within 5 seconds on the displav Ice on off To switch the ice maker on press the ice on off button until one of the two icons comes i To deactivate the function repeat the procedure until both icons go off Ice maker This function enables to select the type of ice desired crushed ice or ice cubes For further information refer to the section Using the ice and water dispenser section Ice and water dispenser light The light can be switched on and off bv pressing the light button on the control panel or pressing one of the two dispenser levers the light will switch off automaticallv once the water or ice has been dispensed 29 USING THE APPLIANCE Water filter Es This symbol indicates the state of the water filter When switching on the appliance for first use or after replacing the filter the filter icon shows three dashes In
5. time the light inside the dispenser comes on and goes off when the lever is released It is not necessary to press hard on the levers to activate the dispenser Pressing hard will not result in faster dispensing or greater quantities 32 USING THE AUTOMATIC ICE MAKER After switching on the refrigerator it usually takes overnight for the first ice cubes to form When selecting crushed ice the cubes are crushed just before being dispensed therefore the crushed ice mav come out with a slight delav Noise from the ice crusher is normal and pieces of ice may vary in size When changing from crushed ice to ice cubes a small amount of crushed ice may come out together with the first cubes Normal ice production consists of about 12 to 14 batches of ice cubes in a 24 hour period The quantity and size of the ice cubes depend on the mains water pressure Ice cubes production can be increased by decreasing the temperature on the freezer compartment Recommendations for the use of the automatic ice maker When the door of the freezer compartment is open ensure that the small flap which functions as a sensor to stop the distribution of ice from the automatic ice maker to the ice container located on the inner door is not obstructed To remove and replace the ice container Insert your fingers in the opening at the bottom of the container and place your thumb on the release button 2 Holding the base of the container with both hands pres
6. time their number will decrease depending on the use of the appliance and the natural wear of the filter charge itself When all the dashes disappear and the icon starts flashing the filter needs replacing Important Only replace the cartridge after all three dashes have disappeared from the filter icon Replace the cartridge and press the OK button until the three dashes reappear on the display The water filter is located under the freezer compartment door ALARMS The alarm icon is connected with the acoustic signal Important To disable the acoustic signal press the OK button Black out alarm ES AN The alarm black out activates when a prolonged interruption of the power supply has caused an increase in temperature in the freezer compartment The freezer display will flash showing the maximum temperature reached in the compartment during the interruption and the acoustic signal will come on Important Before consuming any food from the compartment ensure that this is still suitable for consumption Door open alarm 01 The door alarm svmbol lights and the acoustic alarm is activated when one or both doors of the refrigerator and or freezer have remained open When the doors are left open for more than 2 minutes the symbol and N icon flash and an acoustic signal sounds Operation alarm 9 This symbol with the activation of the acoustic signal and the of letters on the display indicates that there
7. INSTRUCTIONS FOR USE BEFORE USING THE APPLIANCE SAFEGUARDING THE ENVIRONMENT PRECAUTIONS AND GENERAL RECOMMENDATIONS IF THE APPLIANCE IS NOT GOING TO BE USED MAINTENANCE AND CLEANING STORING FREEZING AND THAWING FOOD DESCRIPTION OF THE APPLIANCE MULTIFLOW AIR DISTRIBUTION GUIDE TO THE INSIDE PARTS USING THE APPLIANCE USING THE ICE AND WATER DISPENSER USING THE AUTOMATIC ICE MAKER CHANGING A WATER FILTER CARTRIDGE TROUBLESHOOTING GUIDE 21 BEFORE USING THE APPLIANCE Vour new appliance is designed exclusivelv for domestic use After unpacking the appliance make sure it is not damaged and that the door closes properlv Anv damage must be reported to the dealer within 24 hours of deliverv of the appliance Wait at least two hours before switching the appliance on to ensure that the refrigerant circuit is fullv efficient Installation and the electrical connection must be carried out bv a qualified technician according to the manufacturer s instructions and local safetv regulations Clean the inside of the appliance before using it SAFEGUARDING THE ENVIRONMENT I Packing A The packing material is 100 recyclable and bears the recycling symbol For disposal comply with the local regulations Keep the packing materials plastic bags polystyrene parts etc out of the reach of children as they are a potential source of danger 2 Scrapping Disposal The appliance is manufactured using recycla
8. actures instructions and current standard safety regulations 38 INSTALLATION BEFORE INSTALLING THE REFRIGERATOR WATER CONNECTION ELECTRICAL CONNECTION LEVELLING YOUR REFRIGERATOR INSTALLING CUSTOM DOOR PANELS INSTALLATION DIMENSIONS AND REQUIREMENTS REMOVING THE FREEZER REMOVING THE REFRIGERATOR MOUNTING THE FREEZER DOOR C MOUNTING THE REFRIGERATOR D HORIZONTAL ALIGNMENT OF FREEZER AND REFRIGERATOR DOORS E VERTICAL ALIGNMENT OF FREEZER AND REFRIGERATOR DOORS F BEFORE INSTALLING THE REFRIGERATOR Vour new appliance 5 FULL FROST model exclusivelv for domestic use i e both refrigerator and freezer compartments are provided with an automatic defrosting function This manual contains indications and warnings for correct and safe installation of the appliance read it carefully before starting installation operations The model you have purchased may differ slightly with respect to some descriptions in this manual Install the appliance in a dry and well ventilated place Avoid locations in direct sunlight or near a source of heat oven heating etc If this cannot be avoided install the appliance respecting the following minimum distances Coal or paraffin stoves 30 cm Electric and or gas stoves 3 cm To allow product handling and sufficient air circulation leave at least cm clearance at the sides since this manual covers several models Keep this man
9. ame procedure until the symbol goes off Note This function does not disconnect the power to the appliance ice maker or light but simply deactivates the dispenser levers Y Fast freezing freezer UN This function must be activated before freezing fresh food To activate the function press the menu button until the fast freezing symbol appears on the left of the display The symbol starts flashing and the freezer door icon comes on Press OK to confirm The function will automatically deactivate after 24 hours lt can also be deactivated manually at any time by repeating the procedure Fast cooling refrigerator UN This function is used to speed up the cooling process for fresh foods This function is activated by pressing the menu button until the fast cooling symbol appears on the right of the display The symbol starts flashing and the refrigerator door icon comes on Press OK to confirm The function will automatically deactivate after 6 hours It can also be deactivated manually at any time by repeating the procedure Vacation al This function deactivates the refrigerator compartment if the user is going away for sometime This function is activated by pressing the menu button until the vacation symbol appears The symbol flashes and the refrigerator compartment temperature disappears from the display Press OK to confirm To reactivate the refrigerator compartment repeat the operation After activating the function remove
10. ble material This appliance is marked in compliance with European Directive 2002 96 EC on Waste Electrical and Electronic Equipment WEEE By ensuring the correct disposal of this appliance vou can help prevent potentiallv negative consequences for the environment and the health of persons The symbol the appliance or on the accompanying documents indicates that this appliance should not be treated as domestic waste but must be taken to a special collection centre for the recycling of electrical and electronic equipment When scrapping the appliance make it unusable by cutting off the power cable and removing the doors and shelves so that children cannot easily climb inside and become trapped Scrap the appliance in compliance with local regulations on waste disposal taking it to a special collection centre do not leave the appliance unattended even for a few days since it is a potential source of danger for children For further information on the treatment recovery and recycling of this product contact your competent local office the household waste collection service or the shop where you purchased the appliance 22 Information This appliance does not contain CFCs The refrigerant circuit contains RI 34a HFC or R600a HC see the rating plate inside the appliance Appliances with Isobutane R600a isobutane is a natural gas without environmental impact but is flammable Therefore make sure the refr
11. bs e Before replacing the light bulb remove the light guard that may be present This will have to be put back after replacing the light bulb e Therefrigerator accepts light bulbs with a bavonet tvpe mount These do not need unscrewing screwing when replacing e The ice water dispenser light bulb has a standard screw type mount and therefore needs to be screwed in place Replace the lamp with one of the same tvpe available from the After sales Service or from authorised dealers 24 STORING FREEZING AND THAWING FOOD INTRODUCTION Wrap food so that no water moisture or condensate can enter this will prevent odours or aromas going from one part to another in the refrigerator ensuring better preservation of frozen foods Use plastic containers with hermetic lids aluminium travs aluminium foil plastic film and waterproof plastic wraps NOTE Never place hot food in the freezer Allow hot foods to cool to room temperature for 30 minutes then wrap and freeze Cooling hot foods before freezing saves energy and prolongs the life of the appliance SEALING When sealing food in bags remove the air liquids need space to expand Fasten the top of the bag with a string Put the label inside transparent bags use self adhesive labels for applving on the outside of opaque bags DEFROSTING Useful suggestions RAW VEGETABLES place directly in boiling water without thawing and cook normally MEAT large cuts thaw i
12. e risk of children becoming trapped and suffocating do not allow them to play or hide inside the appliance e Do not swallow the contents non toxic of the ice packs in some models e Do not eat ice cubes or ice lollies immediately after taking them out of the freezer since they may cause cold burns USE e Before carrying out any maintenance or cleaning operation unplug the appliance or disconnect it from the power supply All appliances equipped with an automatic ice maker and water dispenser must be connected to a water supply that only delivers drinking water with mains water pressure of between 0 17 and 0 81 Mpa 1 7 and 8 1 bar Automatic ice makers and or water dispensers not directly connected to the water supplv must be filled with drinking water only Use the refrigerator compartment onlv for storing fresh food and the freezer compartment only for storing frozen food freezing fresh food and making ice cubes e Do not store glass containers with liquids in the freezer since they may burst The Manufacturer declines any liability if the above advice and precautions are not respected 23 IF THE APPLIANCE IS NOT GOING TO BE USED In case of power failures of up to 24 hours Keep the doors of the appliance closed In this wav the stored food will stav cold as long as possible For further information see chapter Using the appliance section Black out alarm If the appliance is not going to b
13. e the shelves pull the shelf out as far as it goes then lift and remove it Removing the crisper or meat drawer slide the drawer out as far as it goes 2 with one hand underneath the drawer lift and pull it out 3 the drawer will come off the runners and can be pulled out further 4 to remove it completely the drawer must be turned front end up rear end down Removing and refitting the glass drawer lid Lift the front of the frame about 10 cm with one hand then lift the back of the frame and pull it out with the other To replace the lid follow the inverse procedure Note To remove the drawers and lids in the freezer compartment follow the same procedure as for the refrigerator Meat vegetable drawer temperature control device e The cold air is conveyed inside the meat drawer through an opening between the refrigerator compartment and the freezer compartment In this way the temperature inside the meat drawer is kept lower than the rest of the refrigerator The air flow can be adjusted by means of the special slider To store vegetables in the meat drawer shift the control device all the way to the left to the vegetables setting This avoids possible damage due to the vegetables freezing Crisper moisture control device e The level of humidity inside the crisper can be adjusted by moving the slider in the desired position By moving the slider to the far right humidity will be eliminated from the compartment This
14. e used Disconnect the appliance from the power supplv Remove all the food if you are going away for more than three weeks the appliance has an automatic ice maker Shut off the water supplv to the automatic ice maker 2 Emptv the ice bucket Leave the doors open enough for air to circulate inside the compartments This will prevent the formation of mould and bad odours MAINTENANCE AND CLEANING Before any cleaning or maintenance operation always disconnect the appliance from the power supply e Periodically clean the appliance with a cloth and a solution of lukewarm water and neutral detergent specific for refrigerator interiors e Never use detergents or abrasives Never clean the refrigerator parts with flammable liquids The fumes can cause fires or explosions e Clean the outside of the appliance and the door seals with a damp cloth and dry with a soft cloth e Do not use steam cleaners e Clean the condenser using a vacuum cleaner remove the front kickplate see installation handbook e The buttons and control panel displav located on the freezer door on some models must be cleaned with a drv cloth do not use alcohol or alcohol derived substances e Therefrigerant svstem pipes are located near the defrost pan and can become verv hot Periodicallv clean them with a vacuum cleaner Replacing light bulbs Attention e Alwavs disconnect the refrigerator from the power supplv before replacing anv light bul
15. ect your green yellow earth wire A to the earth screw located on the appliance B see figure Ensure that the voltage indicated on the appliance data plate corresponds to the mains voltage The plug of the appliance must be easily accessible even after installation so that the appliance can be unplugged if necessary If this is not possible connect the appliance to the mains supply by means of a two pole switch with minimum break distance between contacts of 3 mm fitted at an easily accessible point If the power supply cable plug and socket are not of the same type replace the socket Do not use extension leads or adapters After installation make sure that the appliance is not standing on the power supply cable Disconnect the appliance from the power supply by unplugging it Do not pull the power supply cable LEVELLING YOUR REFRIGERATOR The refrigerator has two front and two rear wheels at the base of the product on each side that can be adjusted see figure A or four wheels of which the two front wheels can be adjusted see figure B If the appliance seems unsteady or you want the doors to close easier adjust the appliance s tilt following the instructions below depending on the model as shown in the figures on the right 1 Check the installation location to be sure you have at least cm clearance on all sides including the top 2 Connect the appliance to the mains power supplv 3 Move the refrige
16. igerant circuit pipes are not damaged Declaration of conformity e This appliance has been designed for preserving food and is manufactured in compliance with Regulation CE No 1935 2004 e This appliance has been designed manufactured and marketed in compliance with safety objectives of the Low Voltage Directive 2006 95 CE which replaces 73 23 CEE and subsequent amendments the protection requirements of Directive EMC 89 336 EEC amended by Directive 93 68 EEC Electrical safety of the appliance can only be guaranteed if it is correctly connected to an approved earthing system PRECAUTIONS AND GENERAL RECOMMENDATIONS INSTALLATION e The appliance must handled and installed two or more persons e Be careful not to damage the floors e g parquet when moving the appliance e During installation make sure the appliance does not damage the power cable e Make sure the appliance is not near a heat source e To guarantee adequate ventilation leave a space on both sides and above the appliance and follow the installation instructions e Keep the appliance ventilation openings free e Do not damage the appliance refrigerant circuit pipes e Install and level the appliance on a floor strong enough to take its weight and in a place suitable for its size and use e Install the appliance in a dry and well ventilated place The appliance is arranged for operation in places where the tempera
17. is a problem with the appliance If this happens call customer service You will be asked to provide the letter code shown on the displav instead of the temperature 30 USING THE APPLIANCE OPTIONAL FUNCTIONS Partv mode Y This function is activated by pressing the menu button until the party mode symbol appears With the symbol flashing press OK to confirm your selection This function enables to use the freezer compartment to cool drinks When the function is selected the icon is animated 30 minutes after activation the time needed to cool a standard 0 75 litres bottle without breaking it the icon will flash and the acoustic signal will come on Remove the bottle and deactivate the function by pressing OK Control panel lock function This function prevents accidental changing of appliance settings or switching off The function is set by pressing the C freezer and the C refrigerator buttons at the same time for 3 seconds the 0 symbol will come on and an acoustic signal will activate To deactivate the function carry out the same procedure until the symbol goes off Automatic ice maker control panel lock This function consists of deactivating ice and water dispensing for easier cleaning or to prevent unintentional use The function is set by pressing the ice maker and the light buttons at the same time for 3 seconds the symbol will come on and an acoustic signal will activate To deactivate the function carry out the s
18. l or taste Has the ice absorbed bad odours Is the quality of the water good Water containing minerals may require a filter Is the food covered Is the ice bucket freezer compartment clean Follow the instructions for the correct ice dispenser water supply Are the pipes correctly connected to the ice dispenser The first ice cubes coming out of the dispenser may have an unpleasant taste therefore it is advisable to discard them and make new ice cubes If the dispenser does not dispense ice when the lever is pressed Change the ice selection from cubes to crushed ice or vice versa in order to remove any ice blocks If the dispenser still does not dispense ice wait a couple of minutes and repeat the operation If the dispenser does not dispense water when the lever is pressed During the first delivery there will be a delay of 15 to 20 seconds due to the system needing to fill with water If the appliance is kept at very cold temperatures and the meat drawer temperature control shutter is open water delivery might be temporarily interrupted Closing the shutter will cause water delivery to recommence within the next 12 hours If there is condensate in the ice and water dispenser Automatic ice maker noises Since the appliance is equipped with an automatic ice maker you may hear humming sound coming from the water valve water trickling and the sound of ice falling into the bucket Press the corresponding
19. n refrigerator compartment without removing the wrapping Before cooking leave at room temperature for a couple of hours MEAT small cuts thaw at room temperature or cook directiv FISH thaw in the refrigerator compartment without unwrapping or cook directly before completely thawed In case of a power failure the freezer compartment will maintain an adequate storage temperature for about 12 hours during this period it is advisable to keep the compartment door closed Do not refreeze partially thawed food ALREADV COOKED FOOD heat in the oven without removing it from the aluminium containers FRUIT thaw in the refrigerator compartment FOOD STORAGE CHART Storage times varv according to the qualitv of the food the tvpe of packaging or wrap used moisture and steam proof and the storage temperature which must be 18 C Food category Months FRUIT Concentrated fruit juice 12 Fruit in general 8 12 Citrus fruit and fresh fruit juices 4 6 VEGETABLES Commercially frozen 8 Home frozen 8 12 STEWS Meat poultry and fish 2 3 FISH Cod sole 6 Salmon 2 3 Mackerel perch 2 3 Already seasoned fish 3 Clams oysters 3 4 Boiled fish crabs 3 4 Raw crayfish 12 Food categorv Months MEAT Sausages 4 weeks or less Hamburgers Beef veal lamb 2 3 ROASTS Beef 6 12 Lamb and veal 6 12 Pork 4 6 Fresh sausages l 2 STEAKS AND CHOPS Beef 8 12 Lamb pork 2 4 POULTRV Chicken or turkev whole or parts 12
20. nts of food have been introduced the motor will run longer in order to cool the inside of the appliance If moisture has accumulated e Make sure the air ducts inside the compartment are not blocked and thus preventing the circulation of air e Make sure food is properly packaged Dry any wet food containers before placing them in the appliance e Make sure the doors are not opened too frequently When the door is opened the moisture contained in the room air enters the appliance The more often the door is opened the faster moisture accumulates especially if the room itself is very humid e If the room is very humid it is normal for moisture to accumulate inside the appliance If there is water in the defrost pan e This is normal in hot and humid weather The pan can even be half full Make sure the refrigerator is level so that water does not spill from the pan If the appliance temperature is too high e Are the appliance controls correctly adjusted e Has a large amount of food been placed in the appliance e Make sure the doors are not opened too frequently and check that the doors close properly e Make sure the air ducts inside the compartment are not blocked and thus preventing the circulation of cold air If the area in contact with the seal is hot to the touch e This is normal in hot weather and when the compressor is working If the doors do not open and close properly e Make sure no food packages are blocking the d
21. oor e Make sure the inside parts or the automatic ice maker are not incorrectly positioned e Make sure the door seals are not dirty or sticky e Make sure the appliance is level If the light does not work e Have you checked the protection devices and fuses of your home s electrical system e Is the power cable plugged into a socket powered with the right voltage e Is the lamp burnt 36 TROUBLESHOOTING GUIDE If the automatic ice maker does not work Has the freezer had enough time to become cold With a new appliance this may take overnight Is the automatic ice maker ON OFF button set to ON Is water reaching the automatic ice maker Is the water cock open The filter may clogged or not correctly installed Firstiv check the filter installation instructions to make sure the filter is correctly fitted and not clogged If installation or clogging is not the problem call qualified personnel or a technician f the dispenser does not work Is the freezer compartment door closed Is the ice bucket correctly installed f the ice dispenser stops working Are the ice cubes stuck because the ice dispenser has not been used for some time Shake the ice bucket to separate the cubes and increase the holding capacitv lt is advisable to throw awav the old ice cubes and make new ice Has the ice dispenser lever been pressed for too long Wait about 3 minutes for the dispenser motor to reset If the ice has an unpleasant smel
22. perishable food from the refrigerator compartment and keep the door closed since the refrigerator maintains an adequate temperature for preventing the formation of odours Note When selecting a function a 5 seconds interval is given to the user to press the OK button to confirm the function Otherwise the user will have to start the procedure again by pressing the menu button 31 USING THE ICE AND WATER DISPENSER First use When the ice and water dispenser is used for the first time the first ice cubes and water coming out of the dispenser may have an unpleasant taste and should therefore be discarded Ice maker The function is activated when the symbol is lit Press the ice maker button to select the symbol corresponding to the type of ice required cubes or crushed the symbol will light up To dispense ice Press the ice maker button and select the required type of ice 2 Press a rigid glass against the ice dispenser lever Hold the glass close to the dispenser opening so that ice does not fall outside of the glass 3 Press lightly on the lever to activate the ice dispenser Pressing hard will not result in faster dispensing or greater quantities 4 To stop dispensing remove the glass slowlv so that ice does not fall outside the glass 5 Do not use fragile glasses to dispense ice Water dispensing To dispense water press a glass against the water dispenser lever removing the glass to stop dispensing at the same
23. rator into its final position 4 Open both doors and remove the plinth to locate the levelling bolts at the left and right of the refrigerator base The top bolt 1 will adjust the rear wheel if provided and the bottom bolt 2 will adjust the front wheel 5 Use the wrench provided to adjust the levelling bolts Turn the levelling bolt clockwise to raise the appliance or anti clockwise to lower it It may take several turns of the levelling bolts to adjust the tilt of the refrigerator Note do not unscrew the levelling bolts too much when lowering the appliance as they could fall out Figure B Aligning the doors If after switching on the appliance and adjusting the refrigerator and freezer doors the doors are misaligned disconnect the appliance from the power supply and adjust both doors as indicated in the enclosed diagram INSTALLING CUSTOM DOOR PANELS e Installing custom door panels If you wish to install custom door panels have the panels made according to dimension drawings Flat panels Flat panels may be fitted in the frames max thickness of panels 6 35 mm Flat panels less than 6 35 mm thick are not recommended Raised panels A raised panel design can be created by screwing or gluing wood panels to 6 35 mm backing or by using 16 mm stock with 6 35 mm routed edges When installing the raised panels leave 5 70 cm clearance between the panels and the rear of the handle to allow holding it freely Weigh
24. s the release button lift the container upwards and remove To replace the ice container in its place place it on its support attached to the inner door and lower in position Note Large amounts of ice cubes should be taken directly from the bucket and not from the dispenser 33 CHANGING A WATER FILTER CARTRIDGE Locate the water filter cartridge cap below the freezer compartment door Rotate the cap counterclockwise to a vertical position and pull the cap and filter cartridge out through the base grille Note Since there is water in the cartridge some spilling mav occur 2 Remove the cartridge cap sliding it off the end of the old cartridge DO NOT DISCARD THE CAP 3 Take the new cartridge out of its packaging and remove the protective cover 4 Slide the cartridge cap onto the new cartridge as shown 5 With cartridge cap in the vertical position push the new filter cartridge into the base grille until it stops Rotate the cartridge cap clockwise to a horizontal position 6 RUN WATER THROUGH THE DISPENSER UNTIL THE WATER RUNS CLEAR about 9 14 litres or 6 7 minutes This will clean the svstem and clear air from the lines Note as air is cleared from the svstem water mav spurt out of the dispenser Ordering replacement filters To order more water filter cartridges please contact vour after sales service 34 TROUBLESHOOTING GUIDE Before contacting the After sales Service
25. setting is better for preserving fruits and vegetables with skin By moving the slider to the far left humidity is maintained inside the compartment This setting is better for preserving leaf vegetables 27 USING THE APPLIANCE FIRST USE Connect the appliance to the water svstem and power supplv refer to the Installation manual When connecting the appliance to the power supply the display will show the temperatures preset by the manufacturer Note Reaching the preset temperatures requires a variable amount of time This time depends on several factors times the door is open amount of food stored ambient temperature Average time is between 2 to 3 hours ess Smeg amp C GAD ICE MAKER LIGHT 28 USING THE APPLIANCE GUIDE TO SELECTING FUNCTIONS Menu This button is used to select the different options shown in the control panel Each time the button is pressed a different option is highlighted OK The OK button is used to confirm the selected function and to deactivate the acoustic signal Stand bv This function turns off the refrigerator and freezer compartments To activate the stand by function press the button for 3 seconds all icons will disappear from the display To reset the function carrv out the same procedure until the previouslv set temperatures are displaved Note Remember that this operation does not disconnect the appliance from the power supplv Freezer temperature The factory
26. t requirements for raised panel inserts The refrigerator door panel should not exceed 10 kg Freezer door panels should not exceed 7 kg combined weight Installing custom door panels 1 VAN Qe WA TEES L 40 9 48 10
27. ture comes within the following ranges according to the climatic class given on the rating plate The appliance may not work properly if it is left for a long time at a temperature outside the specified range Climatic Class Amb C Amb T F From 10 to 32 From 50 to 90 From 16 to 32 From 61 to 90 From 16 to 38 From 61 to 100 From 16 to 43 61 to 110 e Make sure the voltage specified on the rating plate corresponds to that of your home e Do not use single multi adapters or extension cords e For the water connection use the pipe supplied with the new appliance do not reuse that of the previous appliance Power cable modification or replacement must only be carried out by qualified personnel It must be possible to disconnect the appliance from the power supply by unplugging it or by means of a mains two pole switch installed upstream of the socket SAFETY e Do not store or use petrol flammable liquids or gas in the vicinity of this or other electrical appliances The fumes can cause fires or explosions e Do not use mechanical electric or chemical means other than those recommended by the Manufacturer to speed up the defrost process e Do not use or place electrical devices inside the appliance compartments if they are not of the type expressly authorised by the Manufacturer e This appliance is not designed for use by young children or the infirm without supervision To avoid th
28. ual for future consultation If you sell the appliance give it to the new buyer above the appliance and between the rear panel and the wall WATER CONNECTION Disconnect the appliance from the mains power supply before starting operations e The ice maker and water circuit must be connected to a water supply of potable and or chemically purified water e The water connection must be carried out in compliance with local regulations The appliance is supplied with a water tube 2 330 m long already attached to the back of the product Remove the shipping tape from the gray coiled water tubing on the rear of the appliance Connect the transition connector 1 to the household water supply 2 Make sure that the water tube is not twisted The appliance is pre set for operation at pressures between 1 7 and 8 1 bar 25 and 117 PSI e Open the water tap Check for and eliminate any leaks The appliance does not require any adjustment or water drain ELECTRICAL CONNECTION Regulations require that the appliance is earthed The manufacturer declines all liability for injury to persons or animals and for damage to property resulting from failure to observe the prescriptions Make sure that the installation and the electrical connection are carried out by a qualified technician according to the manufacturer s instructions and local safety regulations If your new appliance is provided with a plug with no earth wire conn
Download Pdf Manuals
Related Search