Da-Lite Advantage Electrol
Contents
1. The Da Lite Difference Instruction Book for ADVANTAGE ELECTROL ee DA LITE es DA LITE SCREEN COMPANY INC 3100 North Detroit Street Post Office Box 137 Warsaw Indiana 46581 0137 Phone 574 267 8101 800 622 3737 Fax 574 267 7804 Toll Free Fax 877 325 4832 www da lite com e mail info da lite com IMPORTANT SAFETY INSTRUCTIONS When using your video equipment basic safety precautions should always be followed including the following 1 Read and understand all instructions before using 2 Position the cord so that it will not be tripped over pulled or contact hot surfaces 3 If an extension cord is necessary a cord with a current rating at least equal to that of the appliance should be used Cords rated for less amperage than the appliance may overheat 4 To reduce the risk of electric shock do not disassemble this appliance Contact an authorized service dealer when repair work 15 required Incorrect reassembly can cause electric shock when the appliance is used subsequently 5 The use of an accessory attachment not recommended by the manufacturer may cause a risk of fire electric shock or injury to persons SAVE THESE INSTRUCTIONS PRE INSTALLATION 1 Carefully unpack case from shipping carton DO NOT unpack fabric and roller assembly yet 2 Make sure to recheck measurement of case for proper installation clearance 3 Remove any protective foam or tape from case CASE INS2. BRACKET RED ADJUSTMENT KNOB FIGURE 2 SCREEN ADJUSTMENT FOR 120V SCREENS WITH A BUILT IN LOW VOLTAGE CONTROL 1 Locate the wall switch and remove the cover plate from the 3 button wall switch and remove the switch from the junction box 2 Locate the two tactile buttons on the back of the switch They are square silver with black round buttons See Figure 5 for diagram 3 To adjust the down limit switch press and hold the down tactile button until the LED on back of switch turns solid red This will put the motor in limit set mode Turn the wall switch over and use the down button on front of switch Press and hold until the desired travel position is reached If you travel to far down you can press the up to move the screen upward If you press and let go of either up or down button the motor will do a small jog in that direction for finer adjustment of screen Once desired position is reached turn switch over press and hold down tactile button until the LED on back of switch blinks red twice The down limit is now set 4 To adjust the up limit switch press and hold the up tactile button until the LED on back of switch turns solid green This will put the motor in limit set mode Turn the wall switch over and use the up button on front of switch Press and hold until the desired travel position is reached If you travel to far up you can press the down to move the screen downward If you press and let go of either o
3. Tighten the 1 4 20 nuts securely Complete electrical hook up by snapping motor wire connector into case connector Carefully remove paper and tape from roller assembly DO NOT use a knife or sharp object to cut tape you will damage the screen Pull orange string 7 Test installation by running screen up and down a few times Be prepared to stop screen Standard Duty Cycle 1 MIN ON 3 MIN 8 Re install access door Procedure is reverse of removal step 1 1 ADVANTAGE ELECTROL INSTALLATION FOR 120V SCREENS 120V WIRING DIAGRAM WITH OPTIONAL BUILT IN 1E VANG DIAGRAM POA VIDEO PROJECTOR INTERFACE STANDARD WALL SWITCH GREEN GROUND BLACK DOWN WHITE COMMON UP BLACK HOT WHITE COMMON JUNCTION BOX rp LOCATED IN LEFT ENDCAP 110VOLT AC 60HZ POWER SOURCE GREEN GROUND RED BLACK WHITE SPDT SWITCH WITH FRONT OF BACK OF WALL CENTER OFE AC COMMON WALL SWITCH SWITCH AC HOT 120VAC 60HZ 1 AMP BLACK Y 5 LOW NOTE A SINGLE SWITCH CANNOT BE USED TO OPERATE MORE THAN ONE SCREEN CONTACT THE FACTORY FOR FURTHER RED INFORMATION BLACK 5712 VOLT SCREEN BE USED WITH LVC FIGURE 3 FIGURE 4 TRIGGER ON PROJECTOR CAUTION THE
4. limit knob Fig 1 one turn clockwise Test by WHITE ADJUSTMENT raising picture surface KNOB DOWN approximately two feet then lower again Repeat until desired picture surface position is attained MOTOR MOTOR MOUNT BRACKET BLACK ADJUSTMENT KNOB UP FIGURE 1 SCREEN ADJUSTMENT FOR 220 240V SCREENS WITHOUT BUILT IN LOW VOLTAGE CONTROL Surface travel is stopped automatically in the fully opened and closed positions by limit switches that are properly adjusted at Da Lite Should it be necessary to adjust for more or less drop of picture proceed in the following manner NOTE Use a screw driver or 5 32 Allen wrench to make adjustments MORE SCREEN DROP 1 Place operating switch in down position 2 When the screen stops turn the white down limit knob Fig 2 one turn counterclockwise Test by raising picture surface approximately two feet then lower again Repeat until desired picture surface position is attained LESS SCREEN DROP 1 Raise picture surface approximately two feet above desired level MOTOR POWER CONNECTOR 2 Place operating switch off position 3 Turn the white down limit knob Fig 2 one turn clockwise Test by raising picture surface DOWA E e approximately two feet then lower again Repeat until desired picture surface position is attained MOTOR MOTOR MOUNT
5. ONTROL REMOTE CONTROL LOW VOLTAGE WALL SWITCH UP DI N GND 5V BROWN HOT GREEN 240VAC 50HZ 3 POSITION SWITCH RU GROUND MUST BE O CONNECTED TO BUILDING GROUND 5 GROUND TO CASE DRY CONTACTS ILT PIN OUTS IMPORTANT NOTE The wall switch is REQUIRED to make any limit ere switch adjustments EVEN if a third party control system is used Therefore it is advised to wire the switch or provide a 4 conductor connection that is DN or DATA accessible FIGURE 8 SCREEN ADJUSTMENT FOR 120V SCREENS WITHOUT BUILT IN LOW VOLTAGE CONTROL Surface travel is stopped automatically in the fully opened and closed positions by limit switches that are properly adjusted at Da Lite Should it be necessary to adjust for more or less drop of picture proceed in the following manner Remove two screws to remove access door NOTE Use a screw driver or 5 32 Allen wrench to make adjustments MORE SCREEN DROP 1 Place operating switch in down position 2 When the screen stops turn the white down limit knob Fig 1 one turn counterclockwise Test by raising picture surface approximately two feet then lower again Repeat until desired picture surface position is attained LESS SCREEN DROP 1 Raise picture surface approximately two feet above desired level MOTOR POWER CONNECTOR 2 Place operating switch off position 3 Turn the white down
6. PROJECTOR MUST BE TURNED OFF BEFORE CONNECTING THE TRIGGER WIRES TO THE PROJECTOR FAILURE TO DO SO MAY DAMAGE THE 1 Use 2 conductor 20 24 gauge wire to extend the low voltage connection from the projector s 5 12 volt screen trigger output to the length required to reach the VPI When extending the low voltage connection from the projector s screen trigger output be sure to maintain the proper polarity The red wire from the VPI is the signal and the black wire from the VPI is the ground 2 Connect the wires from the VPI that are labeled Low Voltage Connection to the end of the extended screen trigger wires above RJ 14 PIN OUTS RJ 22 PIN OUTS TAB IS FACING UP TAB IS FACING UP 120V WIRING DIAGRAM WITH OPTIONAL BUILT IN LOW VOLTAGE CONTROL TACTILE BUTTON T RJ 45 PIN OUTS RJ 45 JACK DOWN LIMIT TACTILE BUTTON BACK OF WALL SWITCH FRONT OF WALL SWITCH POWER WIRE IMPORTANT NOTE The wall switch is REQUIRED to make any limit switch adjustments EVEN if a third party control system is GREEN GROUND used Therefore it is advised to wire the switch or provide a 3 conductor connection that is accessible GROUND MUST BE WHITE COMMON CONNECTED TO BUILDING GROUND FIGURE 5 POWER INPUT 120VAC 60HZ ADVANTAGE ELECTROL INSTALLATION FOR 220 240V SCREENS 240V WIRING DIAGRAM WITH OPTIONAL BUILT IN VIDEO PROJECTOR INTERFACE BROWN DOWN BROWNIHON BL
7. TALLATION 1 Remove 2 screws to open junction box Hang case and attach to support structure with bolts See suggested methods of installation on page 5 Tighten bolts until trim flange is flush with ceiling NOTE For proper operation screen assembly must be level after installation 4 Install electrical connections that applies to your unit Make sure to review the wiring diagram for proper hook up NOTE Must be installed in accordance with the requirements of the Local Building Codes the Canadian Electrical Code CEC CAN CSA 22 1 and the National Electric Code NEC NFPA 70 5 Replace junction box cover and secure with 2 screws SCREEN AND ROLLER ASSEMBLY INSTALLATION If your screen was shipped with the motor and roller already installed proceed to step 6 1 Remove access door First remove the 2 screws from the ends Be sure to support the door during this step to avoid injury Then lift the door slightly and pull away from the edge of the case 2 Carefully unpack screen and roller assembly Leave packing paper on roller To install screen and roller assembly insert the motor end into the motor mount bracket as shown in Fig 1 4 Loosen but do not remove two 1 4 20 nuts securing pin end bracket stage left to the case housing Slide the bracket towards the end of the case Insert the motor end square shaft into the motor end bracket and secure with the clip Insert the tip of the roller pin into the bracket and position
8. UE COMMON BLUE COMMON BLACK UP GREEN YELLOW GROUND 240VOLT AC 50HZ 240 VOLT WIRING DIAGRAM FOR STANDARD POWER SOURCE WALL SWITCH GREEN YELLOW GROUND Da Lite offers two styles of 240 volt wall switches for standard operation Please see wiring diagram included in wall switch box included with screen BLACK WHITE FRONT OF BACK OF WALL WALL SWITCH SWITCH RED A ug 7 5 12 VOLT SCREEN FIGURE 6 TRIGGER ON PROJECTOR FIGURE 7 CAUTION THE PROJECTOR MUST BE TURNED OFF BEFORE CONNECTING THE TRIGGER WIRES TO THE PROJECTOR FAILURE TO DO SO MAY DAMAGE THE CONTROLLER 1 Use 2 conductor 20 24 gauge wire to extend the low voltage connection from the projector s 5 or 12 volt screen trigger output the length required to reach the VPI When extending the low voltage connection from the projector s screen trigger output be sure to maintain the proper polarity The red wire from the VPI is the signal and the black wire from the VPI is the ground 2 Connect the wires from the VPI that are labeled Low Voltage Connection to the end of the extended screen trigger wires above 240V WIRING DIAGRAM WITH OPTIONAL BUILT IN OPTIONAL IR AND RF LOW VOLTAGE C
9. en will operate with a low pitched hum 4 Coasting 5 Fabric hangs crooked Printed in U S A Incorrect line voltage Blown fuse Tripped circuit breaker No power to operating switch or junction Power at junction box e Thermal overload tripped f Broken wire in the down or up position g Defective motor limit switch or capacitor h Capacitor burned out Limit switch out of adjustment a Squeaking rubber end plug rubbing on motor b Grinding Foreign object in screen rubbing on roller or fabric c Gear noise a Defective brake a Screen not installed properly b Fabric has backed up inside case c Fabric is damaged c CAUSE SOLUTION Verify 115 125V or 220 240V If insufficient voltage rewire incoming electric line Replace fuse Reset circuit breaker Check above Tighten all loose wire connections Correct any improper connections Down Position Check for power across black and white leads Up Position Check for power across red and white leads Let motor cool down for 15 minutes Try again Check for continuity Cut off old splice and reconnect Replace motor assembly NOTE Motor is a sealed assembly Replace motor assembly See Screen Adjustment section Center roller in case Remove Replace motor assembly Replace motor assembly Check for level and plumb Adjust down limit s
10. r down button the motor will do a small jog in that direction for finer adjustment of screen Once desired position is reached turn switch over press and hold up tactile button until the LED on back of switch blinks green twice The up limit is now set 5 To test limit switch setting press and release the up or down button on the wall switch to operate the screen 6 Replace switch and cover plate on the wall IMPORTANT NOTE The wall switch is REQUIRED to make any limit switch adjustments EVEN if a third party control system is used Therefore it is advised to wire the switch or provide a 3 conductor connection that is accessible SCREEN ADJUSTMENT FOR 220V 240V SCREENS WITH A BUILT IN LOW VOLTAGE CONTROL 1 Remove the cover plate from the 3 button wall switch and remove the switch from the junction box 2 Locate small 3 position switch on back of wall switch See Figure 5 for 120V screens or Figure 8 for 220 240V screens 3 To adjust the down limit switch slide the 3 position switch to the down position Press and hold the down button to run the screen down to the desired stop position Release the button to stop the screen DO NOT PUSH THE STOP BUTTON 4 When the screen is in the desired down position slide the 3 position switch to the off center position The down limit switch is now set 5 To adjust the up limit switch slide the 3 position switch to the up position Press and hold the up button to run the screen up to the de
11. sired stop position Release the button to stop the screen DO NOT PUSH THE STOP BUTTON 6 When the screen is in the desired up position slide the 3 position switch to the off center position The up limit switch is now set 7 To test limit switch setting make sure the 3 position switch is in the off center position Press and release the up or down button on the wall switch to operate the screen 8 Replace switch and cover plate on the wall NOTE If stop button is pressed the wall switch will reverse direction To correct this press the stop button again This will reset the switch You will have to re set both the up and the down limit settings IMPORTANT NOTE The wall switch is REQUIRED to make any limit switch adjustments EVEN if a third party control system is used Therefore it is advised to wire the switch or provide a 4 conductor connection that is accessible ADVANTAGE ELECTROL INSTALLATION VARIABLE POSITION MOUNTING BRACKET MOTOR END AUDIENCE SIDE 3 8 THREADED ROD NOT INCLUDED ATTACHED TO ELECTRICAL MOUNTING BRACKET JUNCTION BOX SELF TRIMMING FINISHED FLANGE CEILING 7 3 4 SEE DETAIL 3 8 THREADED ROD NOT SUPPLIED HANGER BRACKET DETAILA TROUBLESHOOTING SYMPTOM 1 Screen will not operate Motor does not hum 2 Screen does not stop at correct position 3 Noise NOTE Scre
12. witch slowly until roller is exposed and wrinkle comes out then readjust for proper drop Replace fabric 84214 Rev 12 09
Download Pdf Manuals
Related Search