Home

Navman iCN 520

Contents

1. 1 Assemble the suction mount e Slip the locking nut over the ballfoot e Snap the socket clip onto the ballfoot e Screw the locking nut onto the thread of the socket clip until firm 2 Check the Battery Switch on the back of the iCN If it is switched to OFF then remove the stylus and use it to switch the Battery Switch to ON 3 Open the GPS antenna outwards so that it has a clear view of the sky 4 Gently insert the memory card in the Memory Card slot with the label facing the front of the iCN See page 18 for how to insert the memory card 12 iCN 500 series User Manual 5 Insert the iCN into the suction mount a Position the two locating tabs on the underside of the CN into the corresponding slots on the socket clip D Snap the upper side of the iCN into the socket clip 6 Use the alcohol swab to clean and dry the suction cup and the mounting area on the windshield then attach the suction mount to the windshield a Hold the suction cup firmly against the windshield and D Press the lever towards the suction cup 7 Connect the iCN to the vehicle power supply a Plug the small end of the In Vehicle Power Adaptor into the Power Socket on the left side of the iCN b Plug the other end of the In Vehicle Power Adaptor into the 12 V vehicle power socket 8 Press The iCN will turn on 13 popes bulyje5 iCN 500 series User Manual 4 Starting Your CN The Main Menu screen provides
2. D ebe UI 3 am 0 g iCN 500 series User Manual 9 Using the 2D Map screen to Plan a Route You can plan a route directly from the 2D Map screen using the Pop up menu 1 From the Main Menu tap Map The 2D Map screen will display e Move around the 2D Map screen using the 4 way toggle or stylus e To display a smaller area in greater detail press e To display a larger area in less detail press 2 Tap the Map screen or press the 4 way toggle button to display the cross hairs e To remove the cross hairs press ESC 3 Drag the intersection of the cross hairs to a destination Where the cross hairs intersect on a street the street will highlight and the street name will display 4 Tap the intersection of the cross hairs or press the 4 way toggle button to select the street as your destination The E E menu will Ve Ca v Sei a ei ei o DEET Ps UPPER THAMES STREE dn e mn Set as Start Location e Add to Favourites H Show Details 200 uearest PO K Ae SE aal E WATERLOO BRIDGE 5 Select Navigate To The route is calculated and displayed on the 3D Map screen 38 iCN 500 series User Manual 10 Multi stop Trips You can use the Multi stop Trip screen to set multiple destination points for your trip Your route will be calculated to go via each of these points in the specified order Destination points can be added via the Multi stop Trip screen or by selecting Show
3. Thank you for purchasing this Navman iCN We hope you enjoy your new GPS transferable navigation system This user manual will helo you Drive Away with your iCN straight out of the box Navman welcomes your feedback To contact us or visit our website see Support Information on page 97 Box Contents Purchasers of SmartST 2005 software only upgrade kits see the enclosed Upgrade Guide for your Box Contents poye s Duuap USB Cable wy AC Power Pack Protective with Power Cable Carry Case Note The number of plugs depends on the country of purchase Memory O ard may not be included ICN with GPS Antenna Mounting brackets Socket clip 12 V In Vehicle Power Adaptor i SC SG SE with Power Cable Suction cup Locking 2 ballfoot CD ROMs including e SmartST 2005 software including SmartST Desktop e Map data e User Manual PDF format and Adobe Reader Note The number of disks varies with country of purchase Documentation including e User Manual e In Car Installation Guide e Software Product Licence Limited Warranty Agreement e Registration Card iCN 500 series User Manual O al ae D e OI CA Cc 0b g iCN 500 series User Manual 1 Introduction Whether you travel in your own country or elsewhere the iCN will direct you to your destination without the need for map books and second hand instructions The Global Positioning System GPS is available
4. enabled CN 520 only turn on the keypad backlight select the Night Keypad Lighting when the iCN is using external power check box Note This option is only available when Map colours s set to Night display topographical information on the select the Topographic display 2D Map and 3D Map screens check box 67 iCN 500 series User Manual display grid lines on the 2D Map and 3D select the Display Map Grid check box Map screens display a north pointing compass on the select the Display Compass on Map 2D Map and 3D Map screens check box display no entry icons on no entry roads select the Display no entry roads on the 2D Map and 3D Map screens check box 5 Tap Save The Main Menu screen will display Map Preferences Memory Card 1 From the Main Menu tap Preferences 2 From the Preferences screen tap Maps 3 From the Maps screen tao Memory card The Maps Memory card screen will display 4 To activate a map select the map check box Note There may be more than one page of map listings depending on the number of maps installed To view additional pages of map listings scroll down using the 4 way toggle or Dress 5 Repeat step 4 until all required maps are selected 6 Tap Save The Main Menu screen will display 68 iCN 500 series User Manual Map Preferences Points of Interest POIs Points of Interest in a region are grouped into types This function allows
5. postal code ZIP code Point of Interest POI intersection city town country or state You are going to You are going to UNITED KINGDOM UPPER THAMES STREET Find area CITY OF LONDON LONDON Find street UNITED KINGDOM Find postal code Go to centre of street Find Point of Interest Enter house number Change country Find intersection As you specify each part of the address it will display in the You are going to field at the top of the screen The available options will change to reflect the parts of the address still to be completed Keyboard Screen The Keyboard screen will display when you are required to enter text such as when searching for a street name As you select each character the first two results will display Tap d to see more search results Search results will be listed in matching order with the closest matches appearing at the top of the list The Keyboard screen can display in three modes alphabet alternate and number symbol Gage gdeteghhf UPPER TH Saleen ee UPPER TH_ UPPER THAMES STREET CITY OF LO UPPER THAMES STREET CITY OF LO Figure 1 Alphabet Keyboard Figure 2 Alternate Keyboard EN popes Duuap iCN 500 series User Manual House no 1 2 of 2 __ 62 UPPER THAMES STREET CITY OF 68 UPPER THAMES STREET CITY OF O Le D ebe UI 3 0b g Figure 3 Number Symbol Keyboard As you select each character the first two results will displ
6. DEL VATICANO DANMARK DEUTSCHLAND ESPANA FRANCE D Select a country from the list The Destination screen will display 40 iCN 500 series User Manual Step Three Find the Area of Your Destination Point a From the Destination screen tap Find area The Keyboard screen will display Enter Area 1 5 of 50 LONDESBOROUGH ENGLAND LONDON ENGLAND b Use the Keyboard screen to find the area of your destination point For information on using the Keyboard screen see pages 21 22 The Destination screen will display You are going to ONDON ENGLAND UNITED KINGDOM Go to centre of area Find street Find Point of Interest Step Four Find the Street of Your Destination Point a From the Destination screen tap Find street The Keyboard screen will display Enter street 1 1 of 1 UPPER TH UPPER THAMES STREET CITY OF LO 41 iCN 500 series User Manual b Use the Keyboard screen to find the street of your destination point For information on using the Keyboard screen see pages 21 22 The Destination screen will display You are going to PPER THAMES STREET Go to centre of street Enter house number Find intersection Step Five Find the House Number of Your Destination Point a From the Destination screen tap Enter house number The Keyboard screen will display Note If the Enter house number option is not displayed house numbers are not available for your selected stree
7. Do not disconnect the USB cable from the iCN USB Socket until the Map Display screen has refreshed and the installed map or maps have changed colour the default colour for installed maps is yellow 82 iCN 500 series User Manual Removing Maps from your ICN 1 Open SmartST Desktop Start gt Programs gt Navman gt SmartST Desktop 2005 for iCN500 series 2 Open the Maps on iCN section iCN tab gt Maps on ICN 3 Click the map to be removed and select Remove from iCN from the pop up menu The map will be removed from your iCN 83 iCN 500 series User Manual 20 Installing a Language on Your ICN 510 The iCN 510 stores English language files in the CN internal memory by default and other languages on the memory card that came with your iCN The following procedure will replace English on your iCN with another language Only complete this procedure if one of the following conditions applies e You want to use a memory card other than the one that came with your CN e One or more files was deleted from your memory card or e You purchased your iCN in United Kingdom or Australia and want to install a language other than English Prerequisites You must have these programs installed on your computer e SmartST Desktop in the language that you require and e Microsoft ActiveSync 3 7 1 or higher H you do not have both programs installed install them now by completing nstalling SmartST Desktop on Your Computer
8. Name box then click OK The file name can be up to eight characters with no spaces 89 iCN 500 series User Manual 2 Add a POI to the POI File e On the PO Editor window Edit menu click New The PO Details window will open Derien Cegeer Mates Second Daca De oge ue P 7 papaka Loge hb S bk sl fp sip k He Is RB CW e Type a description for the POI in the Description box e On the Degrees Minutes Seconds tab type or select the degree minute and second of the POI latitude in the Latitude boxes e On the Degrees Minutes Seconds tab type or select the degree minute and second of the POI longitude in the Longitude boxes e To save the POI click OK 3 Repeat step 2 until all POIs have been added to the POI file 4 On the File menu click Save The POI file is saved 5 Complete Saving a Custom PO File to your CN below Importing a Custom POI File 1 Download a PO file from the Internet and save it on your computer 2 Open the POI file using the POI Editor e On the SmartST Desktop Map menu click Points of Interest The PO Editor window will open e On the PO Editor window File menu click Open Text File The Open dialogue box will open e Select the POI file from your local or network drive then click Open 3 Complete Saving a Custom POI File to your CN below Saving a Custom POI File to your CN 1 On the SmartST Desktop Map menu click Points of Interest The PO Edi
9. Names with Dates If a street name contains a date or a number search by the first number Example 1 If searching for Faubourg du 13 Juillet 1920 search by 13 Example 2 If searching for Avenue du 14 Avril 1914 search by 14 Example 3 If searching for Rue de la 1 ere Arm e search by 1 poye s Bunya Streets Named After People excluding Italy If a street name is a person s name including at least a first and last name search by the first name Example 1 If searching for Rue Albert Mathieu search by Albert Example 2 If searching for Fred Archer Way search by Fred Example 3 If searching for Franz Grillparzer Strasse search by Franz Street Named After People Italy In Italy if a street name is a person s name including at least a first and last name search by the last name Example 1 If searching for Via de Angelo de Thomasis search by Thomasis Example 2 If searching for Via Placido Giovanella search by Giovanella Example 3 If searching for Via della Giacomo Marca search by Marca Postcodes in United Kingdom and Netherlands When searching by postcode in United Kingdom or Netherlands type the postcode with spaces and without the last two letters Example 1 If searching for RH6 9ST search by RH6 9 Example 2 If searching for 3514 BN search by 3514 For exact European st
10. and follow the prompts The POI file is saved to the iCN as a Custom POI type e f you want to change the file name edit the file name in the POI File Name window File Name box then click OK The file name can be up to eight characters and cannot contain spaces Deleting a Custom POI File from your CN 1 On the Map menu click Points of Interest The PO Editor window will open 2 On the File menu click Manage POI Files The Manage PO Files window will open displaying a list of custom POI files installed on your iCN 3 Click the File Name or Size of the POI file to delete 4 Click Delete The file is removed from the list but is not yet deleted 5 To select another file to delete go back to step 2 otherwise proceed to step 6 6 Click OK and accept the changes The selected file or files are deleted 91 iCN 500 series User Manual Backups You can save backups of all iCN Preferences and Favourites to your computer TO 1 Back up your Preferences Favourites and My Home On the SmartST Desktop File menu click Backup The Backup window will display Click New Backup The New Backup window will display Click OK The New Backup window will close The backup will be listed on the Backup window Close the Backup window Delete a Backup On the SmartST Desktop File menu click Backup The Backup window will display Select from the list the backup to delete 3 Click Delete
11. available maps is cross hatch blue Note If your computer opens Windows Explorer close the Windows Explorer window Maps available on the Map CD in your CD drive are displayed in cross hatch blue 3 e Australian New Zealand and North American users If you have already activated a Map Product Key for your country go to step 7 otherwise continue to step 4 e European users If you have already activated a Gold Pan European Map Product Key activates all maps in Europe go to step 7 otherwise continue to step 4 4 Click the map you want to install to your iCN Note You may need to install multiple maps to cover the desired geographical area 5 If you connect to the Internet via a dial up connection connect to the Internet now 6 Follow the prompts to activate your Map Product Key including e Enter your Map Product Key from the back of the CD box when prompted e You will be prompted to enter or update your contact details so Navman can advise you when updates are released e Your computer will connect to the Internet and activate your Map Product Key e f you are activating a map from a continental region that was not previously installed on your iCN follow the prompts to activate the new region The four continental regions are Europe North America Australia and New Zealand 81 iCN 500 series User Manual e When activation has completed the map will change colour the default colour for activated maps i
12. free of charge at any time and is accurate to within 5 m 15 ft Your iCN map provides street level detail for door to door navigation including Points of Interest POIs such as accommodation petrol stations railway stations and airports Use this manual to learn how to operate your iCN efficiently and safely and discover all the different features available to you GPS and GPS Signals The Global Positioning System is a network of satellites that transmit accurate time and position information worldwide GPS receivers receive signals from these satellites and use the information to determine an exact location Satellites orbit the earth at around 12 000 miles While a GPS receiver can detect signals from up to 12 satellites at any time only three signals are needed to provide a position or GPS fix latitude and longitude for vehicle navigation systems The iCN GPS antenna receives GPS signals To receive GPS signals ensure that the iCN is outdoors or in a vehicle outdoors and the GPS antenna has an unobstructed view of the sky The iCN can operate in all weather types except snowfall For details about GPS and your CN see page 20 Safety Notice WARNING In a vehicle it is your sole responsibility to place secure and use the iCN in a manner that will not cause accidents personal injury or property damage The user of this product is solely responsible for observing safe driving practices It is your responsibility to read
13. l l l Tap with the stylus to select menu options or enter information Displays the Main Menu screen Press and hold to reset the iCN Menu Turns the iCN on or off Power When off the iCN enters a suspended state Cancels an action returns to the previous screen and deletes ESC the last text character on the Keyboard screen hold down for longer to delete a whole line at once Cycles through the 2D Map 3D Map Next Turn and Next 4 Page Turns screens displays additional preferences or search result screens when available Displays a smaller area in greater detail on the Map and 3D Map screens or press and hold to increase the screen brightness O O OOOO Displays a larger area in less detail on the Map and 3D Map screens or press and hold to decrease the screen brightness iCN 500 series User Manual Component Description 4 Way Toggle Selects Main Menu options keyboard characters and Preferences moves around the 2D Map screen to select a destination and scrolls through lists such as lists of search results press centre to confirm the selected menu option text or preference press up or down to adjust the viewing angle on the 3D Map screen Speaker Outputs voice commands and warnings Use the Volume control to adjust Back Components Component Description Battery Switch Must be set to ON for normal use Switching to OF
14. last viewing 1 Remove the iCN from the suction mount bracket if necessary then gently push the GPS receiver back towards the iCN The receiver will click into place 2 Press The iCN will enter a suspended state and the screen will turn off Power Saving Suspended State To save battery power your CN will automatically enter a Suspended state after a set period of time You can change the default suspended state settings at the Power Options screen Main Menu gt Preferences gt More Preferences gt Hardware gt Power Options Power Options External Power E Go to Power Saving Mode if not used for F 5 minutes E Internal Backup Battery Go to Power Saving Mode if not used for G i Minute Kk Note If you are not going to be using the iCN for a period of time switch the Battery Switch to OFF to save battery power 16 iCN 500 series User Manual Reset ICN Normally you do not need to reset your iCN however should your iCN not turn on or not respond you can reset it to solve the problem To reset your iCN either a Press and hold tt The message Reset Device will display Tap Yes b Use the stylus to press the Reset button on the top of the iCN poye s Dumap 17 iCN 500 series User Manual 5 Memory Card Your iCN came with a memory card containing a preactivated map of the region in which it was purchased To navigate to your destination you will first need to insert the memory card in
15. of 99 MARL ssid MARATHON AVENUE DARLING POINT MARATHON LANE DARLING POINT b Use the Keyboard screen to find the street of your destination For information on using the Keyboard screen see pages 21 22 The Destination screen will display You are going to MARATHON AVENUE DARLING POINT NEW SOUTH WALES AUSTRALIA Go to centre of street Enter house number Find intersection Step Six Find the House Number of Destination a From the Destination screen tap Enter house number The Keyboard screen will display Note If the Enter house number option is not displayed house numbers are not available for your selected street Tap Go to centre of street to display the Preview screen Go to step c House ro 10f1 DR 4 MARATHON AVENUE DARLING PO 2 a 1 EE T 8 9 0 30 iCN 500 series User Manual b Use the Keyboard screen to find the house number of your destination For information on using the Keyboard screen see pages 21 22 The Preview screen will display You are going to 4 MARATHON AVENUE DARLING POINT NEW SOUTH WALES AUSTRALIA DARL JG POINT DARLING POINT ROAD c Complete one of the following e To calculate the route and open the 3D Map screen tap Go The 3D Map screen will display e To display the destination on the 2D Map screen tap the preview map The 2D Map screen will display e To save the destination as a Favourite tap Save The New Favourite screen
16. power source before entering Suspended state by tapping the left or right arrows or using the left and right sides of the 4 way toggle 16 iCN 500 series User Manual If you want to change the time to select the Go to Power Saving Mode if not used for check elapse before entering box under Internal Backup Battery suspended state when select the time to elapse when connected to an external using battery power power source before entering Suspended state by tapping the left or right arrows or using the left and right sides of the 4 way toggle 6 Tap Save The Main Menu screen will display Startup Preferences 1 From the Main Menu screen tap Preferences The Preferences screen will display 2 From the Preferences screen tao More Preferences The second Preferences screen will display 3 On the second Preferences screen tap Startup The Startup screen will display Startup Show at startup Tutorial screen Language selection screen Show Tutorial 4 Complete the following display the Tutorial on select the Tutorial screen check box startup display the Language select the Language selection screen check box screen on startup Note If only one language is available on the iCN the Language screen will not display on startup even if this check box is selected view the Tutorial select Show Tutorial The first Tutorial screen will display Press d repeatedly to cycle through the Tutori
17. then click OK The backup is deleted Close the Backup window Restore a Backup On the SmartST Desktop File menu click Restore The Restore window will display Select the backup from the list then click Restore The Restore File Selection window will display 3 Select or clear the check boxes to indicate which part of the backup to restore Click OK The Restore File Selection window will close and the backup will be restored Close the Restore window 92 iCN 500 series User Manual 23 Accessories You can purchase separately almost all items that came with your iCN including additional mounting kits and in vehicle power adaptors The following accessories are also available for your iCN mMCX External Antenna Required for vehicles with heated windscreens or to boost GPS performance in weak signal areas and in areas with poor or limited visibility of the open sky AC Power Adaptor Kit AC power cable with adaptor plugs for the following regions e Western Europe e United Kingdom e Australia New Zealand e United States Canada Earohones Earphones for listening to voice instructions in privacy Remote Control Button functions are the same as the iCN control buttons except that the iCN cannot be turned on using the Remote Control The Remote Control is supplied with the iCN 510 or 520 Premium edition 93 iCN 500 series User Manual Appendix Street ypes Note Belgi
18. would be necessary to install all equivalent detailed maps e exclude smaller roads and have a reduced level of geographical detail You can add and remove Basemaps using the Basemap Installer see below Install Basemap 1 Open SmartST Desktop if it is not already open Start gt Programs gt Navman gt SmartST Desktop 2005 for iCN500 series 2 On the Map menu click Basemaps The Navman Basemap Installer window will open Mawnan Basemap Ineetaller 3 Click the appropriate Add button to install the Basemap to the iCN memory card or memory card reader not supplied 86 iCN 500 series User Manual Activate Basemap 1 Disconnect the USB cable from the iCN The iCN will turn on e f the ICN does not turn on press 2 From the Ch Main Menu screen tap Preferences 3 From the Preferences screen tap Maps 4 Complete one of the following e f the Basemap is on the iCN from the Maps screen select Internal Memory The Maps Internal Memory screen will display e f the Basemap is on the memory card from the Maps screen select Memory Card The Settings Memory Card screen will display 5 To activate the Basemap select the Basemap check box 6 Tap Save The Main Menu screen will display Remove Basemap 1 Open SmartST Desktop if it is not already open Start gt Programs gt Navman gt SmartST Desktop 2005 for iCN500 series 2 On the Map menu click Basemaps
19. your iCN Important If any of the files on the memory card are deleted or if you are using a different memory card from the one that came with your iCN you may need to install a language to the iCN internal memory and install maps to your memory card To install a language see Changing Language below for installing maps using SmartST Desktop on your computer see Installing SmartST Desktop on Your Computer on page 78 and Installing Maps Using SmartST Desktop on page 87 O ap D e UI CA C E fo g Inserting Memory Card Gently insert the card in the SD MMC slot with the label facing the front of the iCN Removing Memory Card Gently push down on the top edge of the card to release it and pull it out of the slot 6 Changing Language CN 510 The memory card that came with your iCN 510 contains a selection of languages As long as this memory card is inserted in your iCN you will be able to navigate using any of these languages by selecting one at the Language screen at startup or at the Preferences Language screen see page 66 The iCN 510 can store one language in internal memory which is UK English by default If you are using a different memory card to the one supplied with your iCN you will only be able to navigate using this one language To change the language stored in internal memory complete nstalling a Language on Your CN 510 on page 84 18 iCN 500 series User Manual ICN 520 The memo
20. CE D Select a country from the list The Destination screen will display 24 iCN 500 series User Manual Step Three Find the Area of Destination a From the Destination screen tap Find area The Keyboard screen will display Enter Area 1 5 of 50 LONDESBOROUGH ENGLAND LONDON ENGLAND G popes Duuap A wW b Use the Keyboard screen to find the area of your destination For information on using the Keyboard screen see pages 21 22 The Destination screen will display You are going to LONDON ENGLAND UNITED KINGDOM Go to centre of area Find street Find Point of Interest Step Four Find the Street of Destination a From the Destination screen tap Find street The Keyboard screen will display Gig deeg UPPER TH UPPER THAMES STREET CITY OF LO 29 O D ebe UI 3 0b g iCN 500 series User Manual b Use the Keyboard screen to find the street of your destination For information on using the Keyboard screen see pages 21 22 The Destination screen will display You are going to UPPER THAMES STREET CITY OF LONDON LONDON UNITED KINGDOM Go to centre of street Enter house number Find intersection Step Five Find the House Number of Destination a From the Destination screen tap Enter house number The Keyboard screen will display Note If the Enter house number option is not displayed house numbers are not available for you
21. Details from the pop up menu on the 2D Map screen then Add to Trip You can save up to 200 multi stop trios each with up to 14 destination points Case Study One Europe and New Zealand Th case study will show you how to set a multi stop trip by selecting your country then area then street then house number for each destination point Note This case study applies to Europe and New Zealand only For navigating in Australia Canada and USA see page 44 Step One Start Your Multi stop Trip a From the Main Menu tap Multi stop Trip The Multi stop Trip screen will display Multi stop Trip b Tap Add The Aad to Trip screen will display Add to Trip Favourites Recent c Tap Address or POI The Destination screen will open 39 iCN 500 series User Manual Note You can also add destination points using Favourites recent destinations and nearest Point of Interest You are going to UNITED KINGDOM Find street Find postal code Find Point of Interest Change country Step Two Select the Country of Your Destination Point If you only have the map of one country installed and selected that country is selected for your destination point by default and cannot be changed Go to Step Three Find the Area of Your Destination Point a From the Destination screen tap Change country The Select country screen will display Select country 1 8 of 23 UNITED KINGDOM ANDORRA BELGIQUE CITTA
22. ES STREET A UC VICTORIA sre 1 b Le CS wf e REET 10 4 Tap Delete A Warning dialogue box will display asking for confirmation to delete the Favourite 5 Tap Yes The Favourite is deleted The Favourite screen will display 62 iCN 500 series User Manual Navigating to a Favourite 1 From the Main Menu tap Go To 2 From the Go To screen tap Favourites The Favourite screen will display 3 Select a Favourite The Preview Favourite screen will display You are going to W OG UPPER THAMES STREET Pipe A CHANGE AP aes iF Oe N VICTORIA STREE DU a Ze EE l wa GEN EN Da 4 Tap Go The route is calculated and displayed on the 3D Map screen Navigating to My Home 1 From the Main Menu tap Go To 2 From the Go To screen tap My Home The route is calculated and displayed on the 3D Map screen 63 iCN 500 series User Manual 16 Preferences You can modify the following preferences to suit your needs screen Brightness 1 Press and hold either the or button to display the Brightness scale 2 To increase screen brightness press To decrease screen brightness press The Brightness scale comprises ten rectangular boxes in a row As screen brightness is increased the first seven boxes progressively turn from gray to green the last three turn red You can also adjust brightness from the Screen preference screen See page 74 Volume 1 Rotate the Volume Control button
23. F will turn the battery off saving battery power GPS Receiver Receives signals from GPS satellites when lifted out to the horizontal position External Antenna Socket Connection socket for GPS mMCX External Antenna not included Protected by rubber cover p pes Buyo O 0b ae D e OI CA ke g iCN 500 series User Manual side Components TT Component Description SD MMC Slot Slot for memory card Memory card must be inserted with label facing forward Stylus Used to tap the screen to make selections and enter information Pull out of the slot to use and insert in the slot to store Volume Control Rotate up or down to hear a sound test rotate and hold to adjust volume e Headphone Socket Connection socket for headphones or earphones not included End Components 8 A Component Description Reset Resets the iCN press using the stylus 2 USB Socket Connection socket for USB cable to your computer Power Socket Connection socket for vehicle power adaptor or AC power pack cable 10 iCN 500 series User Manual stylus The stylus is your input device Pull the stylus out of the slot and extend it for ease of use Store it in the slot when not in use e Tap the screen with the stylus to select e Tap and drag the screen with the stylus to navigate the Map and 3D Map s
24. List screen Instruction 5 8 of 17 STRAIGHT 0 6 A40 HOLBORN VIADUCT mi THIRD EXIT 0 7 A40 HOLBORN VIADUCT mi EXIT LEFT 0 7 A40 HOLBORN mi gt D The nstruction List screen is similar to the Next 4 Turns screen except that it displays your entire route e Use iih to cycle through the instruction list 53 iCN 500 series User Manual Summary Tap Summary to display the Route Summary screen containing your From and To addresses Estimated Time to arrival and the Distance remaining to your destination Route Summary From VWEEDINGTON ROAD CAMDEN TOWN LONDON NWS 4 27 WRAXHILL ROAD VIL Estimated time Distance ESC amp If you are navigating a multi stop trip the information displayed will relate to your next destination point Skip Next Destination Tap Skip Next Dest to skip the next destination point of your trip Only available when navigating a multi stop trip Cancel Route Tap Cancel Route to cancel the route 54 iCN 500 series User Manual 12 The 2D Map Screen Pop up Menu The Pop up menu allows you to access navigational functions from the 2D Map screen To display the Pop up menu complete the following 1 From the Main Menu tap Map The 2D Map screen will display e Move around the 2D Map screen using the 4 way toggle or stylus e To display a smaller area in greater detail press e To display a larger area in less detail press 2 Tap the Map screen or pr
25. NAVMAN ION SOO series with SmartST 2005 User Manual ICN 510 ICN 520 English Europe Australia New Zealand iCN 500 series User Manual Contents Keren 5 Neg MANE OOM TO EE 7 E TE 8 3 Positioning the ICN in a vele 12 A Starting OUT ION seein rA 14 SO AO E a E A 18 SE aigle alo leiere 18 FF Eeer 20 8 Setting your DESTINATION seesssssrrrrrrrnrenerrrrrrrrrreeessens 21 By Address Europe and New Zealand 24 By Address Australia Canada and UA 28 By POI Europe and New Zealand 32 By POI Australia Canada and UA 35 9 Using the 2D Map Screen to Plan a Houte 38 10 Multi stop lee 39 Europe and New Zealand 39 Australia Canada and UA 44 Ti VIEWING VOU EE 50 12 The 2D Map Screen Pop up Mem DO 13 AVOIDING AN Are 56 14 TROUTS Demons talo TE 57 15 Favourites ANd My Hiome 59 16 Preferences cccccccseceeceeseseeeeeeeeeseesseeseaseeeeaeaesesauenseesaaases 64 e SIM De kO ee 78 Toe eelere WIN WE 80 19 Installing Maps Using SmartST Desktop n se 81 20 Installing a Language on Your CN Bn 84 21 Continuous Continental Navigation cccccccceecesessseeeeeeeees 86 22 SmatST Desktop Advanced Features 88 BPG CCSS ONS ege 93 Appendix Street TYOES ccceccccecssesseeceeeeeeeeeeeeeeseaeeeseeetesaeseeees 94 SUDO IEN 97 Sane i aioe en citer tact E AE AA LE A 97 Pao ET rector E EE EE E 97 iCN 500 series User Manual iCN 500 series User Manual
26. PLAZA RAMBLA RONDA Switzerland German BOULEVARD CHAUSSEE PLATZ STRASSE Switzerland French AVENUE CHAUSSEE IMPASSE MONT MONTAGNE PLACE QUARTIER ROUTE ROUTE NATIONAL RUE SQUARE Switzerland Italian CONTRADA CORSO FRAZIONE LARGO PIAZZA PIAZZALE VIA VIALE United Kingdom AVENUE BOULEVARD CENTRE CRESCENT 96 iCN 500 series User Manual Support Information Support for Australia Navman Australia Pty Ltd PO Box 479 Gladesville NSW 2111 Australia pocnsupport aus navman com www navman com Support for New Zealand Navman NZ Ltd PO Box 68 155 Newton Auckland New Zealand pcnsupport nz navman com www navman com Support for Europe Navman Europe Limited 4G Gatwick House Peeks Brook Lane Horley Surrey RH6 9ST United Kingdom Support www navman europe com support php www navman europe com Support for US and Canada Navman USA Limited 2 142 Burbank Foothill Ranch CA 92610 United States of America Phone 866 9 NAVMAN support navmanusa com www navmanusa com NAVMAN DISCLAIM ALL LIABILITY FOR ANY USE OF THIS PRODUCT IN A WAY THAT MAY CAUSE ACCIDENTS DAMAGE OR VIOLATE THE LAW Compliance This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operat
27. Reinstall SmartST on Your iCN Ensure that your iCN is still on and connected to your computer then open SmartST Desktop Start gt Programs gt Navman gt SmartST Desktop 2 You will be prompted to install SmartST on your iCN Click Yes and follow the prompts on your computer and iCN 3 You will be prompted to register your iCN Click No as your iCN has been preregistered 4 On the Tools menu select Recover registration information from Navman 5 Follow the prompts to recover your iCN registration information e Your computer will connect to the Internet to recover your iCN registration information e When your registration information is displayed click Next There is no need to enter an Application Key as your iCN has been preregistered 6 When registration recovery is complete close SmartST Desktop and disconnect your iCN from your computer Your iCN will restart in the new language 85 iCN 500 series User Manual 21 Continuous Continental Navigation Basemaps allow you to seamlessly navigate between installed maps without installing maps of all regions along your route Each Basemap covers a large area such as Western Europe or continental United States and contains main roads that connect cities and towns On the Basemap you can select a road or POI as your departure point or destination All Basemaps e contain roads and ferry connections of high national and international importance e use less memory than
28. The Navman Basemap Installer window will open 3 Select the Basemap to remove 4 Click the appropriate Remove button to remove the Basemap from your iCN memory card or memory card reader or iCN 500 series User Manual 22 omartS I Desktop Advanced Features This section details advanced features of SmartST Desktop If you have not installed SmartST Desktop see page 75 To Find a City or Town 1 From the Map menu click Find City The Find City window will open Find City City Name partial match ok ec Eccles England United Kingdom Eching Bayern Germany Echt Limburg Netherlands Echternach Echternach Luxembourg Eckental Bayern Germany Eckernf rde Schleswig Holstein Germany Ecublens Yaud Switzerland 2 Type the name of the city or town in the City Name field The list of available cities will reduce to match your search 3 Double click the name of the city or town The Map Display will rotate to centre on the selected city or town and E will mark the city or town location Map Colours and Textures To access the Desktop Colours section Desktop tab gt Settings gt Colours Adjust the settings to change the look of the map type Colour Settings Description ap on CH A z ER Controls map colours Displays the e map border colour e map colour e map border width Adjusts the map border width Controls the map display e solid colour e no colour e crosshatch text
29. a specified area on the map Up to ten Avoid Areas can be added Avoid Areas are displayed as shaded areas If no alternative route around an Avoid Area exists you will be routed through an Avoid Area Adding an Avoid Area 1 From the Main Menu screen tap Map The 2D Map screen will display 2 Tap the Map screen or press the 4 way toggle button to display the cross hairs 3 Use the stylus or 4 way toggle to position the intersection of the cross hairs to the area that you want to avoid 4 Tap the intersection of the cross hairs or press the 4 way toggle button to display the Pop up menu 5 Select Add Avoid Area An Avoid Area is displayed 6 Set the Avoid Area to the correct size and position using the 4 way toggle 7 Tap the Avoid Area or press the 4 way toggle to enable the Avoid Area Deleting an Avoid Area 1 From the Main Menu screen select Map The 2D Map screen will display 2 Tap the Map screen and move the cross hairs over the Avoid Area that you want to delete 3 Tap the intersection of the cross hairs or press the 4 way toggle button to display the Pop up menu 4 Select Delete Avoid Area The Avoid Area is deleted Deleting All Avoid Areas 1 From the Main Menu screen tap Preferences 2 From the Preferences screen tap My Data The My Data screen will display 3 From the My Data screen tap Clear Data The Clear Data screen will display 4 Select Clear Avoid Areas When the warning dialo
30. access to all of the iCN s functions including navigating to a destination Step One Turn CN On 1 Check the Battery Switch on the back of the iCN If it is switched to OFF then remove the stylus and use it to switch the Battery Switch to ON O ul e D ebe UI 3 am 0 g 2 Gently pull the bottom of the GPS receiver away from the iCN The receiver will lift out to a horizontal position to allow it to obtain a GPS fix 3 Press The iCN will turn on 14 iCN 500 series User Manual Step Two Language Screen iCN 510 If you purchased your iCN 510 in Australia Canada United Kingdom or United States then English is chosen by default and the Warning screen will display instead of the Language screen Go to Step Three Warning Screen To change the language from English to another see nstalling a Language on Your iCN 510 on page 84 CN 520 If you purchased your CN 520 in Australia Canada New Zealand or United States then English is chosen by default and the Warning screen will display instead of the Language screen Go to Step Three Warning Screen European Users UK English Wm Nederlands US English H Francais Deutsch i Italiano Espa ol Svenska BE Dansk E Do not show on startup 1 Tap your language choice Note Ensure that the memory card supplied with your iCN is inserted in the SD MMC slot see page 14 If you are using a different memory card or fil
31. al screens 5 Tap Save The Main Menu screen will display ag iCN 500 series User Manual 17 SmartST Desktop SmartST Desktop is used to manage maps to and from your iCN obtain software updates manage Custom Points of Interest POls and install Basemaps Note For Windows XP ensure that Windows XP Service Pack 1 has been applied before you install SmartST Desktop Microsoft ActiveSync Microsoft ActiveSync is used to establish a connection between your iCN and your computer ActiveSync 3 7 1 will be installed on your computer if it is not already installed as part of the installation of SmartST Desktop Installing SmartST Desktop on your Computer 1 Close all open programs on your computer 2 Insert the SmartST Application Installer CD into your computer CD drive The SmartST Desktop installer will start e f your computer does not automatically launch the CD start the installation manually Start gt Run Type D Setup SmartST 2005 for iCN500 Series exe where D is the letter assigned to your CD drive Click OK 3 Follow the screen prompts to install SmartST Desktop including e Select your preferred language for SmartST Desktop when prompted e Review and accept the Licence Agreement for SmartST Desktop and Microsoft ActiveSync if not already installed on your computer when prompted e Install Microsoft ActiveSync if not already installed on your computer when prompted e Select a destinatio
32. and follow the vehicle mount installation instructions and to use the product consistent with your government s laws regulations Consult the vehicle manual to ensure the mounting location is safe It is your sole responsibility to adhere to the following safety instructions at all times e Do not operate the iCN while driving or place the iCN in a position that obstructs the driver s view e Do not mount the iCN in a way that may be distracting or interfere with the safe operation of the vehicle the deployment of airbags or other safety equipment e Do not leave the iCN in view while your vehicle is unattended especially in strong or direct sunlight e Do not use or handle the iCN when it is hot leave it to cool out of direct sunlight Failure to adhere to these instructions may lead to serious personal injury including death or property damage Navman disclaims all liability for use of the iCN that contributes to injuries death property damage or violates law popes Duuap iCN 500 series User Manual 2 ICN Features We recommend that you familiarize yourself with the iCN s basic operations such as using the stylus 4 way toggle and Volume control Front Components O 0b se D e OI CA Cc 0b g 8600 900 Component Description Amber indicates that battery is charging Charge Indicator W s l Green indicates that battery is fully charged Displays maps and menu options Touch Screen l
33. anual Step Two Select the Country of Your Destination Point If you only have the map of one country installed and selected that country is selected for your destination point by default and cannot be changed Go to Step Three Select the State of Your Destination Point a From the Destination screen tao Change country or Change country or state The Select country screen will display Select country 1 3 of 3 CANADA USA D Select a country from the list The Destination screen will display e f you only have the map of one state installed and selected that state is selected for your destination by default Go to Step Four Find the Town or City of Your Destination Point Step Three Select the State of Your Destination Point If you only have the map of one state installed and selected that state is selected for your destination by default and cannot be changed Go to Step Four Find the Town or City of Destination Select state 1 8 of 8 AUSTRALIAN CAPITAL TERRITORY NORTHERN TERRITORY QUEENSLAND SOUTH AUSTRALIA TASMANIA VICTORIA WESTERN AUSTRALIA a Select a state from the list The Destination screen will display 45 iCN 500 series User Manual Step Four Find the Town or City of Your Destination Point a From the Destination screen tap Find town city The Keyboard screen will display Enter Area ene ea DARL DARLING POINT NEW SOUTH WALES DARLINGHURST NEW SOUTH WALES C bel
34. ap to scroll the options You must have a route calculated to view these options e Speed e Time e Heading e Distance to Turn e Distance to Go e ETA Estimated Time of Arrival e Time to Go iCN 500 series User Manual Next Turn Screen The Next Turn screen displays information that you need for the next turn the direction of the turn and the distance to the turn A route must have been calculated for this screen to be able to display Access to this screen is controlled by the Display preferences screen To view the Next Turn screen when a route has been calculated press ON to cycle through the screens The next instruction Direction of next turn Tap to hear next instruction Distance to the next turn GPS strength indicator Tap to display the Satellite Signal Strengths screen LEFT CORNWALL ROAD m BA 135 STAMFORD STREET Your current location Tap to display the Main Menu screen Next 4 Turns Screen The Next 4 Turns screen displays the next four turns of your route the turn direction the street name and the distance to the turn A route must have been calculated for this screen to be able to display Access to this screen is controlled by the Display preferences screen Map of the next turn Additional information can display here Press the 8 way toggle left or right to scroll the options e Speed e Time e Heading e Distance to Turn e Distance to Go e ETA Estimated Time of Arriva
35. ay Tap m to see more search results e To select a character or a search result tap the character or search result e To delete a character press ESC or tap lt lt hold ESC to delete the line e To display the number symbol Keyboard screen Figure 3 tap 123 e To display the alternate Keyboard screen Figure 2 press or tap Alt e To display the alphabet Keyboard screen Figure 1 press or tap ABC Preview Screen The Preview screen is used to display a preview of your destination before navigating to it saving It as a Favourite or displaying it on the 2D Map screen You are going to You are going to ge KS eh Week EC NM STRENSALL DRIVE i E NEWLANDS AVENUE C HES GIE l A RYNDLE CRESCENT me ESC amp e To display a smaller area in greater detail press e To display a larger area in less detail press e To display your destination on the 2D Map screen tap the preview map The 2D Map screen will display e To save your destination as a Favourite tap Save The New Favourite screen will display See Favourites and My Home on page 59 e To calculate the route and open the 3D Map screen tap Go The 3D Map screen will display e To view Point of Interest POI details when your destination is a POI tap E The POI Detail screen will display 22 iCN 500 series User Manual Address Search Rules The following rules apply when searching for a destination in Europe Street
36. baa bia T S b Use the Keyboard screen to find the town or city of your destination For information on using the Keyboard screen see pages 21 22 The Destination screen will display You are going to DARLING POINT NEW SOUTH WALES AUSTRALIA Go to centre of area Find street Find Point of Interest Step Five Find the Street of Your Destination Point a From the Destination screen tap Find street The Keyboard screen will display eee MAR MARATHON AVENUE DARLING POINT MARATHON LANE DARLING POINT 46 iCN 500 series User Manual b Use the Keyboard screen to find the street of your destination point For information on using the Keyboard screen see pages 21 22 The Destination screen will display You are going to MARATHON AVENUE DARLING POINT NEW SOUTH WALES AUSTRALIA Go to centre of street Enter house number Find intersection Step Six Find the House Number of Your Destination Point a From the Destination screen tap Enter house number The Keyboard screen will display Note If Enter house number option is not displayed house numbers are not available for your selected street Select Go to centre of street to display the Preview screen Go to step c 4 MARATHON AVENUE DARLING PO oo eee Pe E H Eom E9 0 b Use the Keyboard screen to find the house number of your destination point For information on using the Keyboard screen see pages 21 22 The Preview
37. ble SmartST Demonstration to be played 65 iCN 500 series User Manual move the Preference for motorways slider towards Less often to use roads other than motorways where possible when calculating a route move the slider towards More often to use motorways where possible when calculating a route move the Preference for urban roads slider towards Less often to use roads other than urban roads where possible when calculating a route move the Preference for urban roads slider towards More often to use urban roads where possible when calculating a route select Set default on the first Routing screen This will restore default setting for Route Type Preference for motorways and Preference for urban roads select the Avoid toll roads check box select the Avoid unsurfaced roads check box select the Avoid ferries check box select the Toll roads check box to display a warning message at the start of your trip if your route includes toll roads select the Unsurfaced roads check box to display a warning message at the start of your trip if your route includes unsurfaced roads select the Ferries check box to display a warning message at the start of your trip if your route includes ferries select the Demonstrate Route check box This allows you to plan and view a route without a GPS fix See page 55 for more information select the Repeat check box select the SmartST Demonstration check box The dem
38. creens popes Duuap Internal Battery The iCN has an internal battery that when fully charged should power the iCN for 4 hours You can monitor battery power at the Power Status screen Main Menu gt Preferences gt More Preferences gt Hardware gt Power Status Power Status External Power Status Off Internal Backup Battery Charge High Charging the Battery When the battery is charging the Charge Indicator is amber when the battery is fully charged the Charge Indicator is green e To charge the iCN in a vehicle plug the vehicle power adaptor into the Power Socket on the bottom of the iCN and the other end into the vehicle power socket e To charge the iCN using an electrical wall outlet plug the AC power pack into the Power Socket on the bottom of the iCN and the other end into the wall outlet 11 iCN 500 series User Manual 3 Positioning the CN in a Vehicle Before you begin check if your vehicle is fitted with a heat reflective or heated windscreen If So you will need to purchase an external antenna for your iCN to receive GPS signals See page 93 Follow the safety notice on page 7 to ensure that the iCN does not obstruct the driver s view or interfere with the operation of vehicle airbags and safety devices O 0 e D e OI CA ke 0b g Assembling the CN Suction Mount Choose a position on the windshield that is clearly visible to the driver without obstructing the view of the road
39. cross hairs or press the 4 way toggle to display the Pop up menu Your current position is marked with Your next turn is highlighted in a different colour from future turns The colour will depend on the theme you Additional information can are using display here Tap to scroll the options You must have a route calculated to view these options e Speed a Time e Heading e Distance to Turn e Distance to Go e ETA Estimated Time of Arrival Your current location e Time to Go Tap to display the Main Menu screen GPS strength indicator Tap to display the Satellite Signal Strengths screen 50 iCN 500 series User Manual 3D Map Screen The 3D Map screen displays when a route is calculated oriented to the travelling direction with an adjustable horizon To view the 3D Map screen when a route has been calculated press i to cycle through the screens e To adjust the viewing angle press the 4 way toggle up or down e To display a smaller area in greater detail press e To display a larger area in less detail press e To display the Go To Pop up summary press the 4 way toggle Direction of the next turn LEFT CORNWALL ROAD Tap to hear next instruction GPS strength indicator Tap to display the Satellite Signal Strengths screen Your current location Tap to display the Main Menu screen 51 North oriented compass Additional information can display here T
40. ct the Type of POI a From the Destination screen tap Change country The Select country screen will display Select country 1 8 of 23 UNITEDKINGDOM ANDORRA BELGIQUE CITTA DEL VATICANO DANMARK DEUTSCHLAND ESPANA FRANCE D Select a country from the list The Destination screen will display 32 iCN 500 series User Manual Step Three Select the Type of POI Note To narrow the search for a type of POI you can first search by Area a From the Destination screen tap Find Point of Interest The Select PO screen will display Select POI 1 7 of 42 ANY TYPE AIRLINE ACCESS AIRPORT popes Duuap el AMUSEMENT PARK jaa CAR DEALER D Select a POI type from the list The Keyboard screen will display Enter POI 1 2 of 2 SCARBOROUGH NORTH BAY SCARS SCARBOROUGH SOUTH BAY SCARBO c Use the Keyboard screen to find the POI For information on using the Keyboard screen see pages 21 22 The Preview screen will display You are going to SCARBOROUGH NORTH BAY SCARBOROUGH NORTH YORKSHIRE UNITED KINGDOM STRENSALL DRIVE 33 O al e D e OI CA Cc 0b g iCN 500 series User Manual d Complete one of the following e To calculate the route and open the 3D Map screen tap Go The 3D Map screen will display e To display the destination on the 2D Map screen tap the preview map The 2D Map screen will display e To save the destination a
41. en will display Hardware Preferences Power Status 1 From the Main Menu screen tap Preferences The Preferences screen will display 2 From the Preferences screen tao More Preferences The second Preferences screen will display 09 iCN 500 series User Manual 3 On the second Preferences screen tap Hardware The Hardware screen will display 4 From the Hardware screen tao Power Status The Power Status screen will display Power Status External Power Status Off Internal Backup Battery Charge High 00 0 Ggs 5 Press O to return to the Main Menu screen Hardware Preferences Power Options 1 From the Main Menu screen tap Preferences The Preferences screen will display 2 From the Preferences screen tao More Preferences The second Preferences screen will display 3 On the second Preferences screen tao Hardware The Hardware screen will display 4 From the Hardware screen tao Power Options The Power Options screen will display Power Options External Power E Go to Power Saving Mode if not used for 5 Minutes E Internal Backup Battery Go to Power Saving Mode if not used for ba Minute k 5 Complete the following If you want to change the time to select the Go to Power Saving Mode if not used for check elapse before entering box under External Power suspended state when connected to an external power source select the time to elapse when connected to an external
42. es on your original memory card have been deleted you may need to install a language on your ON internal memory See Changing Language on pages 18 19 e To prevent the Language screen from displaying on each startup select the Do not show on startup check box iCN 520 Selecting the Do not show on startup check box will install the selected language to your iCN internal memory See page 19 for more information 2 Tap m to go to the next screen The Warning screen will display Step Three Warning Screen 1 Read the warning message 2 Tap Accept to confirm that you understand The first Tutorial screen will display Step Four Tutorial Screens 1 Read the Tutorial screen e To prevent the Tutorial from displaying on startup select the Do not show Tutorial on startup check box 2 Tap m to move through each Tutorial screen The Main Menu screen will display 15 popes Duuap iCN 500 series User Manual Main Menu Screen Main Menu Map Multi stop Trip Preferences O G D ebe UI 3 0b g Show Tutorial e Use the stylus to select a Main Menu option e Return to the Main Menu screen at any time by pressing tt e The Route Information option is only available when a route has been calculated See page 53 54 for more information ToTurn ICN Off When your iCN is off it enters a suspended state and the system stops operating When you turn your iCN on it returns to the screen you were
43. ess the 4 way toggle button to display the cross hairs e To remove the cross hairs press ESC 3 Position the intersection of the cross hairs on a destination point Where the cross hairs intersect on a street the street will highlight and the street name will display 4 Tap the intersection of the cross hairs or press the 4 way toggle button to select the street as your destination The Pop up menu will display fon SORES Res i e BSG pack Wd e EE NEW BRIBDGESTREEL Seeche d Eji 1 30 IES S Mle me mee UPPER THAMES STREE THUR STREET Op Set as Start Location Add to Favourites 5 You can choose one of the following options Navigate To Calculates a route from your current location Sets the selected point as your departure point Set as Start Location SmartST will calculate and display the route to your destination Add to Pavountes Displays the New Favourite screen for you to add the selected point as a Favourite Displays the Address Details screen from which you can e View details of the selected point Show Details e Add the point to your multi stop trip e Set the point as your destination point e Save the point as a Favourite Add Avoid Area Adds an Avoid Area for you to size Delete Avoid Area Deletes the selected Avoid Area Displays the Select POI screen BEES Select the POI type then the POI to navigate to iCN 500 series User Manual 13 Avoiding an Area You can calculate a route that avoids
44. g box opens select Yes 5 To return to the Main Menu press i 56 iCN 500 series User Manual 14 Route Demonstrator The Route Demonstrator allows you to e Preview a route e Plan and view a route without a GPS fix such as when you are inside a building Step One Activate Route Demonstrator 1 From the Main Menu screen tap Preferences 2 From the Preferences screen tap Routing The Routing screen will display 3 Press ON twice 4 Select the Demonstrate Route check box 5 Tap Save The Main Menu screen will display Step Two Select Departure Point If you have a GPS fix you do not need to select a departure point unless you want the demonstrated route to start elsewhere 1 From the Main Menu screen tap Map The 2D Map screen will display 2 Tap the Map screen or press the 4 way toggle button to display the cross hairs 3 Position the intersection of the cross hairs on your departure point Where the cross hairs intersects on a street the street will highlight and the street name will display 4 Tap the intersection of the cross hairs or press the 4 way toggle button The Pop up menu will display 3 Select Set as Start Location The Pop up menu will close Step Three Select Destination Point Set a destination either by using the Destination screen see pages 21 37 or by using the 2D Map screen Pop up menu by completing the following 2 Tap the Map screen or press the 4 way toggle butt
45. g navigation select the Enable check box 5 Tap Save The Main Menu screen will display 66 iCN 500 series User Manual Map Preferences Display Settings 1 From the Main Menu tap Preferences 2 From the Preferences screen tap Maps 3 From the Maps screen tap Display The first of two Display screens will display Press d to move through the Display screens Display foom Auto Zoom Next Turn screen Display Next Turn screen Map colour scheme Default gt Default gt Map colours Map colours Day Night Day Night Topographic dlepiay Night Keypad Lighting ESC amp Save ESC d Save Figure 1 iCN 510 Figure 2 iCN 520 4 Complete the following If you want to enable Auto Zoom during navigation select the Auto Zoom check box If selected the 2D Map and 3D Map screen will automatically Zoom in or out depending on your speed to allow optimal route viewing enable access to the Next Turn screen select the Display Next Turn screen check box enable access to the Next 4 Turns screen select the Display Next 4 Turns screen check box change the colour scheme select your preferred scheme from the Map colour scheme box by tapping the left or right arrows or using the left and right sides of the 4 way toggle improve screen contrast in light or dark under Map colours select either Day conditions or Night iCN 520 only If Night is selected the Night Keypad Lighting checkbox will be
46. ill display Step Four Select the Type of POl Note To narrow the search for a type of POI you can first search by Town or City a From the Destination screen tap Find Point of Interest The Select POI screen will display Select POI 1 7 of 60 ANY TYPE AIRPORTS AIRFIELDS Hi AMBULANCE STATIONS BANKS BAYS BEACHES ETC hak BOATRAMPS BOWLING CLUBS D Select a POI type from the list The Keyboard screen will display Enter POI 1 2 of 2 BLACKSMITHS BLACKSMITHS BLACKWALL GOSFORD A B C D E F G J K M N 0 T 36 iCN 500 series User Manual c Use the Keyboard screen to find the POI For information on using the Keyboard screen see pages 21 22 The Preview screen will display You are going to L BLACKWALL GOSFORD NEW SOUTH WALES AUSTRALIA d popes Gulyje5 d Complete one of the following e To calculate the route and open the 3D Map screen tap Go The 3D Map screen will display e To display the destination on the 2D Map screen tap the preview map The 2D Map screen will display e To save the destination as a Favourite tap Save The New Favourite screen will display See Favourites and My Home on page 59 e To change your destination tap ESC The Destination screen will display e To view Point of Interest POI details when your destination is a POI tap The PO Detail screen will display To return to the Main Menu press tt 3 O ul
47. ing in Europe and New Zealand see page 24 Step One Open the Destination screen a From the Main Menu tap Go To D From the Go To screen tao Address or POI The Destination screen will display Important Note i If this is the first time you are setting your destination and you have maps from more than one country installed and selected then the Select country screen will display instead of the Destination screen Go directly to Step Two Select the Country of Destination step b The next time you perform this procedure the Destination screen will open as expected ii If this is the first time you are setting your destination and you have maps from only one country but more than one state installed and selected then the Select State screen will display instead of the Destination screen Go directly to Step Three Select the State of Destination The next time you perform this procedure the Destination screen will open as expected Step Two Select the Country of Destination H you only have the map of one country installed and selected that country is selected for your destination by default and cannot be changed Go to Step Three Select the State of Destination a From the Destination screen tap Change country or Change country or state The Select country screen will display Select country 1 3 of 3 CANADA USA D Select a country from the list The Select state screen will display e f you only ha
48. ing will display when an active POI is within 150 ft of but not necessarily on your route Note Custom POIs must first be installed on your ON using SmartST Desktop before they can be set as active POIs See Points of Interest POI Editor on pages 89 97 1 From the Preferences menu tap Safety Alerts The Safety Alerts screen will display 2 On the Safety Alerts screen tap Active POI The Select Active POI screen will display Select Active POI 1 2 of 2 SPEEDCAM ACTIVE WIRELESS ACTIVE 3 Select a custom POI type The POI Activation Settings screen will display POI activation settings SPEEDCAM ACTIVE Active Audio warning Visual warning Distance to POI m ii 500m 4 Select the Active check box to activate the POI 5 Modify the settings as required e To enable a warning chime when the POI is in close proximity select the Audio warning check box e To enable a visual warning when the POI is in close proximity select the Visual warning check box e Move the Distance to POI slider to select the distance at which the warnings will activate 6 Tap Save The Main Menu screen will display TO iCN 500 series User Manual Alerts Preferences Speed and GPS signals The Safety settings allow you to set safety related warnings 1 From the Preferences menu tap Safety Alerts The Safety Alerts screen will display 2 On the Safety Alerts screen tap Safety The Safety screen will di
49. ion Copyright 2005 Navman NZ Limited Navman is a registered trademark of Navman NZ Limited All rights reserved SmartST Drive Away and Back On Track are trademarks of Navman NZ Limited All rights reserved Microsoft Windows 98 SE ME 2000 or XP SP1 Microsoft ActiveSync and Internet Explorer are registered trademarks of Microsoft Corporation All rights reserved Adobe Reader is a registered trademark of Adobe Systems Incorporated All rights reserved All other trademarks and registrations are the property of their respective owners Published in New Zealand MN000406B Se iCN 500 series User Manual Notes 98 MNOOO0406B
50. ktop has now been uninstalled from your computer 19 iCN 500 series User Manual 18 Updating your CN Updating your Version of SmartST We recommended that you regularly use SmartST Desktop to check the Navman website for SmartST software updates 1 If you connect to the Internet via a dial up Connection connect to the Internet now 2 Open SmartST Desktop Start gt Programs gt Navman gt SmartST Desktop 2005 for iCN500 series On the Setup menu select Update software then Check for updates on the web Your computer will connect to the Internet and display the Navman website CO IN Download the update for your region to your computer if available On the Setup menu select Update software then Update software on iCN Follow the prompts to update your iCN software Wu Upgrading from Previous Version of SmartST See the Upgrade Guide that came with your software upgrade 80 iCN 500 series User Manual 19 Installing Maps Using SmartS T Desktop Your iCN comes with a preactivated map If you require additional maps you must first purchase a Map Product Key Use SmartST Desktop to activate your Map Product Key and install the required map Installing and Activating Maps on your CN 1 Open SmartST Desktop if it is not already open Start gt Programs gt Navman gt SmartST Desktop 2 Insert a SmartST Map CD into your computer CD drive the available maps will display the default colour for
51. l e Time to Go To view the Next 4 Turns screen when a route has been calculated press ON to cycle through the screens The next turn is highlighted at the top of the list GPS strength indicator Tap to display the Satellite Signal Strengths screen EI KEEP RIGHT POULTRY hes KEEP LEFT 0 5 A40 NEWGATE STREET mi STRAIGHT 0 8 A haon VIADUCT mi 75 KING WILLIAM STREET mi Your current location Tap to display the Main Menu screen Back On Track Automatic Rerouting Your route is re directed if you make a wrong turn The symbol will display upper left of the 3D Map and Next Turn screens while the route recalculates D Distance to the next turn Additional information can display here Press the 8 way toggle left or right to scroll the options e Speed e Time e Heading e Distance to Turn e Distance to Go e ETA Estimated Time of Arrival e Time to Go iCN 500 series User Manual Route Information Screen The Route Information screen provides information about your current route and lets you skip a trip destination point or cancel a route The screen is only available from the Main Menu when you are navigating a route Main Menu gt Route Information Route Information Instruction list Summary Skip Next Dest Cancel Route Show Route Tap Show Route to display your entire route on the 2D Map screen Instruction List Tap Instruction list to display the nstruction
52. maps from only one country but more than one state installed and selected then the Select State screen will display instead of the Destination screen Go directly to Step Three Select the State of Destination The next time you perform this procedure the Destination screen will open as expected Step Two Select the Country of Destination If you only have the map of one country installed and selected that country is selected for your destination by default and cannot be changed Go to Step Three Select the State of Destination a From the Destination screen tap Change country or Change country or state The Select country screen will display Select country 1 3 of 3 CANADA USA D Select a country from the list The Select state screen will display e f you only have the map of one state installed and selected that state is selected for your destination by default Go to Step Four Select the Type of POI 35 O ob e ul e OI CA Cc 0b g iCN 500 series User Manual Step Three Select the State of Destination If you only have the map of one state installed and selected that state is selected for your destination by default and cannot be changed Go to Step Four Select the Type of POI Select state 1 8 of 8 AUSTRALIAN CAPITAL TERRITORY NORTHERN TERRITORY QUEENSLAND SOUTH AUSTRALIA TASMANIA VICTORIA WESTERN AUSTRALIA a Select a state from the list The Destination screen w
53. n folder for SmartST Desktop when prompted 4 When the installation has finished click Finish SmartST Desktop will open Desktop and iCN tabs Map Display screen Selected maps Download selected maps to the memory card or memory card reader not supplied Map information Map Colour Key 18 iCN 500 series User Manual 5 If prompted to connect your CN to your computer complete the following e Plug the large end of the USB cable directly into a USB port on your computer not a USB hub plug the small end into the USB Socket on the bottom of your iCN e Plug the small end of the AC Power Pack cable into the Power Socket on the bottom of your iCN plug the other end into the mains e Press O The iCN will turn on e When the following screen displays on your iCN click Next e Microsoft ActiveSync will synchronise with your iCN You are now ready to install maps to your iCN To Open SmartST Desktop Once SmartST Desktop has been installed you can access it from the Start menu Start gt Programs gt Navman gt SmartST Desktop 2005 for iCN500 series Uninstalling SmartST Desktop from your Computer We recommend that you use the Add or Remove Programs feature in your Windows Control Panel 1 Open Add or Remove Programs Start gt Control Panel gt Add or Remove Programs 2 Uninstall Navman SmartST Desktop 2005 for iCN500 Series Note The name of the program may vary from the above SmartST Des
54. o not show on startup check box 4 Tap NN The selected language is installed to your CN The Warning screen will display 5 Continue to Step Three of Starting Your iCN on page 15 19 O ul E D e UI CA C g iCN 500 series User Manual 7 GPS Status Signals are transmitted by Global Positioning System GPS satellites orbiting the Earth You can view your GPS status at any time from the 2D Map 3D Map Next Turn and Next 4 Turns screens The GPS Strength Indicator LE will display green when there is a valid fix 2D or 3D and between one and three bars will display to indicate the strength of the signal the GPS Strength Indicator will display red when no fix is available LEFT CORNWALL ROAD CK UPPER GROUND km h Tap the GPS Strength Indicator to open the Satellite Signal Strengths screen For more detailed information on your current GPS fix see GPS Status on page 73 20 iCN 500 series User Manual 8 Setting Your Destination For your safety enter destination information before you start a journey Do not operate the iCN while driving Select a destination using the Destination Keyboard and Preview screens which used together form a destination wizard This section describes how to use each of these screens and provides two case studies to help guide you through setting your destination Destination Screen The Destination screen is used to select your destination by area street
55. ome The Favourite is saved as My Home The Go To screen will display Editing the Name of the Favourite 1 From the Main Menu tap Go To 2 From the Go To screen tap Favourites The Favourite screen will display 3 Select a Favourite to edit The Preview Favourite screen will display You are going to NEILA 68 UPPER THAMES STREET 2 D He Get y ai ER _ CARTER LANE 61 iCN 500 series User Manual 4 Tap the Name box The Enter text screen will display Enter text C D E F K L MI N S d Y 123 e To select a character tap the character e To delete a character press ESC or tap lt lt hold ESC to delete the line e To display the number symbol Enter text screen tap 123 e To display the alternate Enter text screen press or tap Alt e To display the alphabet Enter text screen press or tap ABC e After you have entered a name for the Favourite tap Save The New Favourite screen will display 5 Complete one of the following e To save as a favourite tap Save as Favourite The Favourite is saved The Go To screen will display e To save as My Home tap Save as My Home The Favourite is saved as My Home The Go To screen will display Deleting a Favourite 1 From the Main Menu tap Go To 2 From the Go To screen tap Favourites The Favourite screen will display 3 Select a Favourite to delete The Preview Favourite screen will display You are going to tte OS UPPER THAM
56. on page 78 Note If you already have SmartST Desktop installed but in a language other than the one you want to install on your ON you must first uninstall SmartST Desktop see Uninstalling SmartST Desktop on page 79 then reinstall SmartST Desktop in the correct language For example if you want to install French on your iCN you must have SmartST Desktop installed on your computer in French Step One Remove SmartST From Your iCN i 2 Insert the memory card in your iCN SD MMC slot Plug the small end of the USB cable into the USB Socket on the bottom of your iCN and the other end into your computer USB socket Microsoft ActiveSync will open and synchronise with your iCN In Microsoft ActiveSync click E Windows Explorer will open displaying the contents of the Ch In Windows Explorer select the Program Files folder and delete it e f you are asked for confirmation click Yes In Windows Explorer open the My Flash Disk folder The contents of My Flash Disk will display Select all files and folders in the My Flash Disk folder and delete them e f you are asked for confirmation click Yes 7 Close Windows Explorer 8 Use the stylus to switch the Battery Switch on the back of the iCN to OFF 84 iCN 500 series User Manual 9 Wait five seconds then switch the Battery Switch to ON The iCN will turn on and display the blue USB screen Microsoft ActiveSync will resynchronise with your iCN 2p Two
57. on to display the cross hairs 2 Position the intersection of the cross hairs on your destination point Where the cross hairs intersects on a street the street will highlight and the street name will display 3 Tap the intersection of the cross hairs or press the 4 way toggle button The Pop up menu will display 4 Select Navigate To The Pop up menu will close The 3D Map screen will display the calculated route in Route Demonstrator mode e f you have selected the Repeat check box on the Routing preferences screen the Route Demonstrator will continue to repeat the route of iCN 500 series User Manual To Disable Route Demonstrator 1 Press O to display the Main Menu screen 2 From the Main Menu screen tap Preferences 3 From the Preferences screen tap Routing The Routing screen will display 4 Press ON twice 5 Clear the Demonstrate Route check box 6 Tap Save Route Demonstrator will be disabled The Main Menu screen will display 58 iCN 500 series User Manual 15 Favourites and My Home You can save up to 200 destinations as Favourites one of which can be saved as My Home My Home can be any designated Favourite but we recommend that it is your home or other common destination You can save a Favourite from the Preview screen after searching for an address or from the Pop up Menu on the 2D Map screen Saving a Favourite 1 Either search for an address using the Destination and Keyboard screen
58. onstration willl navigate between the first and second Favourite after a 10 second delay iCN 500 series User Manual If you want to enable Track Recording contact Navman Customer Support only to be used if required by Navman as we recommend this feature be used Customer Support only under the supervision of a Navman technician 4 Tap Save The Main Menu screen will display Language Preferences 1 From the Main Menu tap Preferences 2 From the Preferences screen tap Language The Language screen will display EE Language English UK Female gt Voice guidance instructions Enable 3 To change your language including the voice scheme used for voice guidance during navigation select your preferred voice scheme from the Language box by tapping the left or right arrows or using the left and right sides of the 4 way toggle iCN 510 If you a purchased your iCN in Australia Canada New Zealand or United States or b you are using a different memory card to that supplied with your CN or c files on your original memory card have been deleted then English is the only language available To change the language from English see nstalling a Language on Your ON 510 on page 84 CN 520 Only languages installed on the internal memory of your CN will be available for selection For more information see nstalling a Language to Your iCN 520 on page 19 4 To enable Voice guidance instructions durin
59. r US English language is selected Hardware Preferences Screen 1 From the Main Menu screen tap Preferences The Preferences screen will display 2 From the Preferences screen tao More Preferences The second Preferences screen will display 3 On the second Preferences screen tap Hardware The Hardware screen will display 4 From the Hardware screen tap Screen The Screen screen will display Screen Touch Screen Align Brightness 74 iCN 500 series User Manual 5 Complete the following align the touch screen tap Align and follow the prompts Note The prompts are available in English only adjust screen brightness move the Brightness slider towards High to increase screen brightness move the Brightness slider towards Low to decrease screen brightness 6 Tap Save The Main Menu screen will display Hardware Preferences Volume 1 From the Main Menu screen tap Preferences The Preferences screen will display 2 From the Preferences screen tao More Preferences The second Preferences screen will display 3 On the second Preferences screen tap Hardware The Hardware screen will display 4 From the Hardware screen tap Volume The Volume screen will display Yolume Yolume Level 5 To increase volume move the Volume Level slider towards High to decrease volume move the Volume Level slider towards Low e Tap Test to test the volume 6 Tap Save The Main Menu scre
60. r selected street Tap Go to centre of street to display the Preview screen Go to step c 62 UPPER THAMES STREET CITY OF 68 UPPER THAMES STREET CITY OF 1 2 3 8 a 9 26 iCN 500 series User Manual b Use the Keyboard screen to find the house number of your destination For information on using the Keyboard screen see pages 21 22 The Preview screen will display You are going to 68 UPPER THAMES STREET CITY OF LONDON LONDON EC4R 1 UNITED KINGDOM o CARTER LAN a ewell atre SLL PUDDLE DOCK kee a CANNON STREET it c Complete one of the following e To calculate the route and open the 3D Map screen tap Go The 3D Map screen will display e To display the destination on the 2D Map screen tap the preview map The 2D Map screen will display e To save the destination as a Favourite tap Save The New Favourite screen will display See Favourites and My Home on page 59 e To change your destination tao ESC The Destination screen will display To return to the Main Menu press CO 2 poye s Dumap O 0b e ul e OI CA C iCN 500 series User Manual Setting Your Destination by Address Case Study Iwo Australia Canada and USA This case study will show you how to set your destination by selecting your country then state then town or city then street then house number Note This case study applies to Australia Canada and USA only For navigat
61. reet type abbreviations see Appendix Street Types on page 94 23 iCN 500 series User Manual Setting Your Destination by Address Case Study One Europe and New Zealand This case study will show you how to set your destination by selecting your country then area then street then house number Note This case study applies to Europe and New Zealand only For navigating in Australia Canada and USA see page 28 O ul D e UI CA C 0b g Step One Open the Destination screen a From the Main Menu tap Go To b From the Go To screen tao Address or POI The Destination screen will display Important Note f this is the first time you are setting your destination and you have maps from more than one country installed and selected then the Select country screen will display instead of the Destination screen Go directly to Step Two Select the Country of Destination step b The next time you perform this procedure the Destination screen will open as expected Step Two Select the Country of Destination If you only have the map of one country installed and selected that country is selected for your destination by default and cannot be changed Go to Step Three Find the Area of Destination a From the Destination screen tap Change country The Select country screen will display Select country 1 8 of 23 UNITED KINGDOM ANDORRA BELGIQUE CITTA DEL VATICANO DANMARK DEUTSCHLAND ESPANA FRAN
62. ress 5 Tap Save The Main Menu screen will display My Data Preferences Clear Data 1 From the Main Menu screen tap Preferences The Preferences screen will display 2 From the Preferences screen tao My Data The My Data screen will display 3 From the My Data screen tap Clear Data The Clear Data screen will display 4 Complete the following clear recent destinations select Clear Recent When the warning dialog box opens tap Yes clear favourites select Clear Favourites When the warning dialog box opens tap Yes Note This option will not clear My Home clear avoid areas select Clear Avoid Areas When the warning dialog box opens tap Yes 5 Press A to return to the Main Menu screen 12 iCN 500 series User Manual GPS Status Signals are transmitted by Global Positioning System GPS satellites orbiting the Earth The Satellite Signal Strengths screen provides a visual representation of the information being received Latitude and longitude are displayed along with a north pointing compass the heading in degrees and ground speed The strength of each satellite is displayed on a bar chart From the Main Menu screen select Preferences gt More Preferences gt GPS status The Satellite Signal Strengths screen will display Satellite Signal Strengths 36 47 32 9 S D H 174 45 48 9 E Okm 42 40 40 O 40 35 35 38 37 36 31 ESC amp You can also access this screen from
63. ry card that came with your iCN 520 contains a selection of languages As long as this memory card is inserted in your iCN and you have not selected the Do not show on startup check box on the Language screen you will be able to navigate using any of these languages by selecting one at the Language screen at startup The iCN 520 can store two languages in internal memory UK English and one which you have installed using the below procedure This means that if you are using a different memory card to the one supplied with your iCN you can navigate using either UK English or your chosen language by selecting one at the Preferences Language screen See page 66 poye s Duuap Installing a Language to your CN 520 To install a language on your iCN the Language screen must be enabled to display at startup If you have disabled the Language screen from displaying at startup or you purchased your CN 520 in Australia Canada New Zealand or United States you must ensure the Language Selection Screen check box is selected on the Preferences Startup screen See page 77 1 Turn on your iCN as per Step One of Starting Your iCN on page 14 e f your ICN is already on reset it as per the instructions on page 17 2 When the Language screen is displayed tap your language choice UK English Gol Nederlands US English H Francais Deutsch H Italiano Espa ol Svenska BEA Dansk E Do not show on startup 3 Select the D
64. s a Favourite tap Save The New Favourite screen will display See Favourites and My Home on page 59 e To change your destination tao ESC The Destination screen will display e To view Point of Interest POI details when your destination is a POI tap El The PO Detail screen will display To return to the Main Menu press tt 34 iCN 500 series User Manual Setting Your Destination by POI Case Study Iwo Australia Canada and USA This case study will show you how to set your destination by selecting a Point of Interest PON A POI is a named site feature landmark or public venue which can be displayed as an icon on the map POls are grouped by type such as parks and museums Note This case study applies to Australia Canada and USA only For navigating in Europe and New Zealand see page 32 Step One Open the Destination screen a From the Main Menu tap Go To D From the Go To screen tap Address or POI The Destination screen will display poye s Bunya Important Note i If this Is the first time you are setting your destination and you have maps from more than one country installed and selected then the Select country screen will display instead of the Destination screen Go directly to Step Two Select the Country of Destination step b The next time you perform this procedure the Destination screen will open as expected ii If this is the first time you are setting your destination and you have
65. s as described in Setting Your Destination pages 21 37 or create a multi stop trip as described in Multi stop Trips pages 39 49 until the Preview screen is displayed 2 Tap Save The New Favourite screen will display New Favourite elite Oo UPPER THAMES STREET 68 UPPER THAMES STREET 435211 CITY OF LONDON LONDON EC4R 1 UNITED KINGDOM Save as My Home ESC amp 3 To change the name of the Favourite tap the Name box The Enter text screen will display Enter text 68 UPPER THAMES STREET e To select a character tap the character e To delete a character press ESC or tap lt lt hold ESC to delete the line e To display the number symbol Enter text screen tap 123 e To display the alternate Enter text screen press or tap Alt e To display the alphabet Enter text screen press or tap ABC e After you have entered a name for the Favourite tap Enter The New Favourite screen will display 59 iCN 500 series User Manual 4 Complete one of the following e To save as a favourite tap Save as Favourite The Favourite is saved The Go To screen will display e To save as My Home tap Save as My Home The Favourite is saved as My Home The Go To screen will display saving a Favourite from the 2D Map Screen 1 From the Main Menu select Map The 2D Map screen will display 2 Tap the Map screen or press the 4 way toggle button to display the cross hairs 3 Position the intersection of
66. s light green Proceed to step 7 The activated map is displayed in light green 7 Click the map to install to your iCN The map will change colour to indicate it has been selected the default colour for selected maps is dark green The map is now listed in the Selected section of the Desktop Selected Maps tab 8 Australian New Zealand and North American users If you have already activated a Map Product Key for your country repeat step 7 until all required maps have been added to the Selected section of the Desktop Selected Maps tab e European Gold Pan European Map Product Key users If you have already activated a Gold Pan European Map Product Key activates all maps in Europe repeat step 7 until all required maps have been added to the Selected section of the Desktop Selected Maps tab e European Silver Single Map Product Key users If you have another Silver Single Map Product Key to activate activates a single map go to step 4 The selected map is displayed in dark green 9 Click an Add to button to install all maps listed in the Selected section of the Desktop Se lected Maps tab to your iCN memory card or memory card reader not supplied SmartST Desktop will install the selected map or maps to your CN or CN memory card When they have been installed the map or maps will change colour the default colour for installed maps is yellow 10 To use your iCN disconnect the USB cable from your iCN WARNING
67. screen will display Add to Trip 4 MARATHON AVENUE DARLING POINT NEW SOUTH WALES AUSTRALIA 47 iCN 500 series User Manual c Select Add to Trip The Multi stop Trio screen will display listing your destination point Multi stop Trip d Complete one of the following Note Destination points added updated or deleted after a multi stop trip has commenced will not affect the current route If you want to add another destination point Note Destination points added after a multi stop trio has commenced will not be included in the current route change the order of your destination points calculate the route e tap Add The Add to Trip screen will display e tao Address The Destination screen will display e go to Step Three Find the Area of Your Destination Point e select a destination point to move from the list The Preview screen will display e tap Move The Multi stop Trip screen will display e use the 4 way toggle to move the selected destination point to the correct position tap Go The 3D Map screen will display the calculated route delete all destination points select Clear delete one destination point save the multi stop trip as a Favourite To return to the Main Menu screen press tt 48 e select a destination point to delete from the list The Preview screen will display e tap Delete From Trip The Multi stop Trip screen will display e tap Sa
68. splay Safety Speed G E mph Warn driver when operating E Warn when GPS lost 3 Complete the following If you want to enable a warning chime select the speed in the Speed box by tapping the left when traveling at or above a or right arrows or using the left and right sides of the designated speed 4 way toggle Tap Save The Safety alerts screen will display Note The GPS signal alert will be activated when a Speed alert is selected enable a visual warning if the select the Warn driver when operating check box Main Menu screen is accessed in a moving vehicle enable a warning chime and select the Warn when GPS lost check box visual warning when the GPS Note The GPS signal alert will be activated when a signal has been lost Speed alert is selected 4 Tap Save The Main Menu screen will display I iCN 500 series User Manual My Data Preferences My Points of Interest My POI Custom Points of Interest POIs are installed from the SmartST Desktop POI Editor See pages 86 85 and listed on the My POIs screen 1 From the Main Menu tap Preferences 2 From the Preferences screen tao My Data 3 From the My Data screen tap My POI The My PO screen will display 4 To select a POI file select the POI check box Note There may be more than one page of PO types depending on the number of maps installed To view additional pages of POI types scroll down using the 4 way toggle or p
69. splay e select Move The Multi stop Trio screen will display e use the 4 way toggle to move the selected destination point to the correct position select Go The 3D Map screen will display the calculated route select Clear e select a destination point to delete from the list The Preview screen will display e tap Delete From Trip The Multi stop Trip screen will display e tap Save The New Favourite screen will display e tap Save The Favourite will save and the Multi stop Trip screen will display iCN 500 series User Manual Case Study Iwo Australia Canada and USA This case study will show you how to set a multi stop trip by selecting your country then area then street then house number for each destination point Note This case study applies to Australia Canada and USA only For navigating in Europe and New Zealand see page 39 Step One Start Your Multi stop Trip a From the Main Menu tap Multi stop Trip The Multi stop Trip screen will display Multi stop Trip b Tap Add The Aad to Trip screen will display Add to Trip Favourites Recent c Tap Address or POI The Destination screen will open Note You can also add destination points using Favourites recent destinations and nearest Point of Interest You are going to NEW SOUTH WALES AUSTRALIA Find town city Find street Find Point of Interest Change country or state 44 iCN 500 series User M
70. t Select Go to centre of street to display the Preview screen Go to step c EE 62 UPPER THAMES STREET CITY OF 68 UPPER THAMES STREET CITY OF b Use the Keyboard screen to find the house number of your destination point For information on using the Keyboard screen see pages 21 22 The Preview screen will display Add to Trip 68 UPPER THAMES STREET CITY OF LONDON LONDON ECAR 1 UNITED KINGDOM kee lt 2 CANNON et ERR Pe q 7 MONUMENT STREET Z ef 42 c Tap Add to Trip iCN 500 series User Manual The Multi stop Trio screen will display listing your destination point Multi stop Trip d Complete one of the following Note Destination points added updated or deleted after a multi stop trip has commenced will not affect the current route If you want to add another destination point Note Destination points added after a multi stop trio has commenced will not be included in the current route change the order of your destination points calculate the route delete all destination points delete one destination point save the multi stop trip as a Favourite To return to the Main Menu screen press af 43 e tap Add The Add to Trip screen will display e tao Address The Destination screen will display e go to Step Three Find the Area of Your Destination Point e select a destination point to move from the list The Preview screen will di
71. the 2D Map 3D Map Next Turn and Next 4 Turns screens by tapping the GPS Strength Indicator has The circle on the right side of the screen displays green when there is a valid fix 2D or 3D and red when no fix is available A fix will be obtained more quickly if the vehicle is stationary than if it is moving The satellites available from your current position are shown as grey red and green coloured bars Red A valid signal but not being used to fix your position A valid signal being used to fix your position 13 iCN 500 series User Manual Measurement Preferences 1 From the Main Menu screen tap Preferences The Preferences screen will display 2 From the Preferences screen tao More Preferences The second Preferences screen will display 3 On the second Preferences screen select Measurements The Measurements screen will display 4 Complete the following change the Position select either the Decimal degrees or the Degrees format minutes seconds option change the local time select the offset from the Coordinated Universal Time UTC offset for your location from the Local time offset box by tapping the left or right arrows or using the left and right sides of the 4 way toggle Next select either the 12 Hour or 24 Hour option for time format choose distance units select either the kilometres or miles option 5 Tap Save The Main Menu screen will display Only available when UK English o
72. the cross hairs Where the cross hairs intersects on a street the street will highlight and the street name will display 4 Tap the intersection of the cross hairs or press the 4 way toggle button The Pop up menu will display E EDE LS E ANNON STREE f NEW BRIDGE STREFLL E Ree REE OL Sn UPPER THAMES STREE Men areas Delete Avoid Area ANN Z200 USE ee L el 33 WATERLOO BRIDGE km h 5 Select Add to Favourites The New Favourite screen will display New Favourite DELLS UPPER THAMES STREET 68 UPPER THAMES STREET 43211 CITY OF LONDON LONDON EC4R 1 UNITED KINGDOM Save as My Home ESC amp 60 iCN 500 series User Manual 6 To change the name of the Favourite select the Name box The Enter text screen will display Enter text 68 UPPER THAMES STREET D E F L MI N U Y 123 Enter e To select a character tap the character e To delete a character press ESC or tap lt lt hold ESC to delete the line e To display the number symbol Enter text screen tap 123 e To display the alternate Enter text screen press or tap Alt e To display the alphabet Enter text screen press or tap ABC e After you have entered a name for the Favourite tap Enter The New Favourite screen will display 7 Complete one of the following e To save as a favourite tap Save as Favourite The Favourite is saved The Go To screen will display e To save as My Home tap Save as My H
73. tor window will open 2 On the PO Editor window File menu click Save to Device The PO Options window will open m J e Je leon Pie aa IIl w _ ae 29 Si 90 iCN 500 series User Manual 3 Modify the POI settings as required If you want to activate the POI select the Active check box Note If you do not activate the POI you will be able to configure only the POI Visibility Level and Icon File settings enable a visual warning when the select the Visual Alert check box POI is in close proximity enable a warning chime when the select the Audio Alert check box POI is in close proximity change the units used to measure select the Metric or Imperial option distance for this POI select the distance from the POI select the distance from the Distance box at which the visual warning should display or the warning chime should sound indicate the priority of this POI move the POI Visibility Level slider left or right when one or more additional POls are in the same locale select a custom POI type icon to Type the path to the icon file to be used to display on the map if you do not represent the POI type in the Icon File box or select a custom icon a default icon select the icon file from your local or network will display drive clicking locating the file and clicking Open The file must be a bitmap bmp graphic with a minimum of 6x6 pixels and a maximum of 32x32 pixels 4 Click OK
74. um and Switzerland each list street tyoes and their abbreviations in three languages Country Street Type Abbreviation Austria BOULEVARD BVD CHAUSSEE CH PLATZ PL STRASSE Belgium Dutch BAAN BERG DREEF LAAN MARKT PARK PLEIN SQUARE STEENWEG STRAAT Belgium French AVENUE BOULEVARD CHAUSSEE IMPASSE MONT MONTAGNE PLACE ROUTE ROUTE NATIONAL RUE SQUARE Belgium German CHAUSSEE PLATZ STRASSE Finland France ALLEE AVENUE BOULEVARD CHAUSSEE DOMAINE FAUBOURG IMPASSE MONT MONTAGNE PASSAGE PLACE QUARTIER ROND POINT ROUTE ROUTE NATIONALE RUE SQUARE TRAVERSE 94 wf Netherlands iCN 500 series User Manual Abbreviation BOULEVARD CHAUSSEE PLATZ STRASSE AVENUE BOULEVARD CENTRE CRESCENT PLACE ROAD ROUTE SQUARE STREET YARD CONTRADA CORSO FRAZIONE LARGO PIAZZA PIAZZALE STRADA STATALE SUPERSTRADA VIA VIALE ALLEE AVENUE BOULEVARD CHAUSSEE DOMAINE FAUBOURG IMPASSE MONT MONTAGNE PASSAGE PLACE QUARTIER ROND POINT ROUTE ROUTE NATIONALE RUE SQUARE TRAVERSE BOULEVARD DIJK DWARSSTRAAT DWARSWEG GRACHT KADE KANAAL LAAN LEANE LOANE PARK PLANTSOEN PLEIN SINGEL STRAAT STRJITTE STRAATWEG WEG a E iCN 500 series User Manual Street Type Abbreviation GT Portugal AVENIDA BAIRRO CALCADA CAMINHO ESTRADA LARGO LARGUINHO PRACA QUARTO QUARTA QUINTA RUA SAO SANTA SANTO Spain AVENIDA CALLE CALLEJON CAMINO CARRETERA GLORIETA PASEO
75. up or down to hear a sound test 2 Rotate the Volume Control button up or down and hold to display the volume bar e Rotate the Volume Control button up or down to adjust the volume You can also adjust volume from the Volume preference screen See page 75 Routing Preferences 1 From the Main Menu tap Preferences 2 From the Preferences screen tap Routing The first of three Routing screens will display Press ON to move through the Routing screens Routing Route Type Quickest _ SS SS a distance Preference for motorways Less often _ _ More often Preference for urban roads Less often zl More often Set default Save VG uk 3 Complete one of the following If you want to change the Route Type move the Route Type slider towards Quickest to give more weighting to the fastest time when calculating a route move the Route Type slider towards Shortest distance to give more weighting to the shortest distance when calculating a route 64 If you want to change the Preference for motorways change the Preference for urban roads revert to default settings avoid toll roads avoid unsurfaced roads avoid ferries receive a warning if your route includes toll roads receive a warning if your route includes unsurfaced roads receive a warning if your route includes ferries enable the Route Demonstrator enable the Route Demonstrator to play repeatedly ena
76. ure SE Controls geographic features displayed on the map Features are only visible if the map has no colour or crosshatch texture 88 iCN 500 series User Manual Map Layers To e i sde your iCN and memory card you can choose map layers to install The layers you can choose from are e Points of Interest POIs e Bodies of water and parks e Land contours topography To access the Map Layers section Desktop tab gt Settings gt Layers Select or clear each checkbox to indicate the layers to install for each map Please select the Map Data Layers that you want to download to the CH elect Data to load IV POIs V Roads Jh Water Parks etc JV Land Contours Points of Interest POI Editor You can create custom Points of Interest POIs using the POI Editor in two ways e by creating your own POI files or e by using compatible POI files downloaded from the Internet A maximum of 25 Custom POI files can be saved on your iCN The Custom POI files are listed on the My POI screen Custom POls can be set to enable a warning chime or visual warning when in close proximity at the Select Active POI screen Creating a Custom POI File 1 Create a new POI File using the POI Editor e On the SmartST Desktop Map menu click Points of Interest The PO Editor window will open e On the PO Editor window File menu click New Text File The PO File Name window will open e Type aname for the file in the File
77. ve The New Favourite screen will display e tap Save The Favourite will save and the Multi stop Trip screen will display iCN 500 series User Manual skipping a Destination Point You can modify a multi stop trip at any time from the Multi stop Trio screen however if you have already commenced a trip changes will not affect the current route Main Menu gt Multi stop Trip To skip a destination point during a multi stop trio complete the following 1 Press tt to return to the Main Menu screen The Main Menu screen will display 2 Tap Route Information The Route Information screen will display 3 Tap Skip Next Dest The next destination point will be skipped and the route recalculated to the following destination point 49 iCN 500 series User Manual 11 Viewing your Route Once a route has been calculated you can view it in several ways Press ila to cycle through the screens 2D Map Screen The 2D Map screen is always oriented North and shows your current position if a GPS fix is active and surrounding street names If a route has been calculated the route and turns are highlighted To view the 2D Map screen either tap Map on the Main Menu screen or when a route has been calculated press fh to cycle through the screens e To display a smaller area in greater detail press e To display a larger area in less detail press e To display the cross hairs tap the map Tap the intersection of the
78. ve the map of one state installed and selected that state is selected for your destination by default Go to Steo Four Find the Town or City of Destination 28 iCN 500 series User Manual Step Three Select the State of Destination If you only have the map of one state installed and selected that state is selected for your destination by default and cannot be changed Go to Step Four Find the Town or City of Destination Select state 1 8 of 8 AUSTRALIAN CAPITAL TERRITORY NORTHERN TERRITORY QUEENSLAND SOUTH AUSTRALIA TASMANIA VICTORIA WESTERN AUSTRALIA poye s Huyg a Select a state from the list The Destination screen will display Step Four Find the Town or City of Destination a From the Destination screen tap Find town city The Keyboard screen wll display Enter Area 1 5 of 50 DARLING POINT NEW SOUTH WALES DARLINGHURST NEW SOUTH WALES a PE E D K L M T b Use the Keyboard screen to find the town or city of your destination For information on using the Keyboard screen see pages 21 22 The Destination screen will display You are going to DARLING POINT NEW SOUTH WALES AUSTRALIA Go to centre of area Find street Find Point of Interest 29 O al G D e OI CA Cc 0b g iCN 500 series User Manual Step Five Find the Street of Destination a From the Destination screen tap Find street The Keyboard screen will display Enter street 1 2
79. will display See Favourites and My Home on page 59 e To change your destination tao ESC The Destination screen will display To return to the Main Menu press tt 31 popes Buyo iCN 500 series User Manual Setting Your Destination by POI Case Study One Europe and New Zealand This case study will show you how to set your destination by selecting a Point of Interest PON A POI is a named site feature landmark or public venue which can be displayed as an icon on the map POls are grouped by type such as parks and museums O ul e D e UI CA C 0b g Note This case study applies to Europe and New Zealand only For navigating in Australia Canada and USA see page 35 Step One Open the Destination screen a From the Main Menu tap Go To b From the Go To screen tao Address or POI The Destination screen will display Important Note f this is the first time you are setting your destination and you have maps from more than one country installed and selected then the Select country screen will display instead of the Destination screen Go directly to Step Two Select the Country of Destination step b The next time you perform this procedure the Destination screen will open as expected Step Two Select the Country of Destination If you only have the map of one country installed and selected that country is selected for your destination by default and cannot be changed Go to Step Three Sele
80. you to select the types you need For example you may be only interested in entertainment venues and want to disable other POI types such as schools 1 From the Main Menu tap Preferences 2 From the Preferences screen tap Maps 3 From the Maps screen tap Points of Interest The Points of Interest screen will display Points of Interest Turn all off Types AIRLINE ACCESS AIRPORT AMUSEMENT PARK BEACH CAMPING GROUND CAR DEALER CASH DISPENSER ESC amp Save 4 You may either choose to display or hide icons of all POI types on the 2D Map and 3D Map screens or to selectively display desired icons chosen from the list of POI types e To display all POI icons i e icons of all POI types on the 2D Map and 3D Map screens select Turn all on To display no icons select Turn all off e To select a specific POI type icon for display select the POI type check box Repeat until all desired POI types are selected Note There may be more than one page of PO types depending on the installed maps To view additional pages of PO types scroll down using the 4 way toggle or press ih 5 Tap Save The Main Menu screen will display 69 iCN 500 series User Manual Alerts Preferences Active POls The Active POI settings allow you to set warning chimes and visual warnings for custom POls that will activate within a chosen distance radius of your location For example a warning chime will sound or a visual warn

Download Pdf Manuals

Related Search

Related Contents

NRS 1-40 - Flowserve Corporation  Zotac ZT-70801-10P NVIDIA GeForce GTX TITAN 6GB graphics card  Compact NSX - elektro oprema  User Manual  User manual for kluwer.cls  

Copyright © All rights reserved. Failed to retrieve file