LG N1941WP-PF
Contents
1. Function Use these buttons to select or adjust functions in the On Screen Display Use this button to make either D Sub or X PORT connector active This feature is used when two input sources are connected to the display Use these buttons to select or adjust functions in the On Screen Display Use W A buttons to decrease or increase the speaker volume on X PORT input Use this button to enter a selection in the On Screen Display AUTO IMAGE ADJUSTMENT When adjusting your display settings always press the AUTO SET button before entering the On Screen Display OSD This will automatically adjust your display image to the ideal settings for the current screen resolution size display mode The best display mode is 16 inches 1360 x 768 19 inches 1360 x 768 Use this button to turn the display on or off This Indicator lights up blue when the display operates normally On Mode If the display is in Sleep Mode Energy Saving this indicator color changes to flicker On Screen Display OSD Control Adjustment Screen Adjustment Making adjustments to the image size position and operating parameters of the display is quick and easy with the On Screen Display Control system A short example is given below to familiarize you with the use of the controls The following section is an outline of the available adjustments and selections you can make using the OSD NOTE Allow the display to2. Settings X PORT support only 16bits color White Balance is performed on black white pattern Check if the screen is set to normal mode The screen blinks e Check if the screen is set to interlace mode and if yes change it to the recommend resolution Check if the screen is set to normal mode Specifications Display Sync Input Video Input Resolution Plug amp Play Power Consumption Dimensions amp Weight Tilt Range Power Input Environmental Conditions Stand Base Power cord NOTE N1642W N1642WP 15 6 inches 39 6 cm Flat Panel Active matrix TFT LCD Anti Glare coating Visible diagonal size 39 6 cm 0 252 0 252 mm pixel pitch D SUB Horizontal Freq 30 66 kHz Automatic Vertical Freq 57 63 Hz Automatic D SUB support 60Hz only except Dos mode X PORT 1440 x 900 60Hz 1280 x 720 60Hz 1360 x 768 60Hz 800 x 600 72Hz 1024 x 768 60Hz D SUB Signal Input 15 pin D Sub Connector Input Form RGB Analog 0 7 Vp p 75 ohm X PORT Signal Input X PORT Connector Input Form X PORT Signal Max VESA 1360 x 768 60 Hz Recommend VESA 1360 x 768 60 Hz DDC 2B Only for D SUB Input On Mode 20W Typ Sleep Mode lt 1 W Off Mode lt 1 W With Stand Without Stand Width 38 17 cm 15 03 inches 38 17 cm 15 03 inches Height 32 39 cm 12 75 inches 26 03 cm 10 25 inches Depth 19 84 cm 7 81 inches 5 67 cm 2 23 inches Net 2 6 kg 5 78 Ibs
3. J ENGINE SJ ENGINE MOVIE This feature lets you easily select the best desired INTERNET image condition optimized to the environment ambient illumination image types etc MOVIE For animation images in videos or movies INTERNET For text images Word processing etc USER User a MENU Exit You can manually adjust ACE or RCM You can save or restore the adjusted value even when using a different environment Y Decrease A Increase a SET Select another sub menu ACE Adaptive Clarity Enhancer Selects the clarity mode RCM Real Color Management Selects the color mode Eee Not applied E m Green enhance Em Flesh tone e Color Enhance NORMAL This is under normal operating conditions DEMO This is just for advertising to customer in the shops It s setting is same with Movie mode and screen is divided by half s The INTERNET and NORMAL features become enabled for X PORT input Troubleshooting Check the following before calling for service No image appears Is the power cord of the Check and see if the power cord is connected display connected properly to the power outlet Is the power indicator Press the Power button light on Is the power indicator e f the display is in power saving mode try moving flickering the mouse or pressing any key on the keyboard to bring up the screen e Try to turn on the PC
4. the computer system and other attached devices is turned off Positioning your display 1 Adjust the position of the panel in various ways for maximum comfort a Tilt Range 5 20 ab 20 a When adjusting the angle of the screen do not put your finger s in between the head of the monitor and the stand body You can hurt your finger s Ergonomic It is recommended that in order to maintain an ergonomic and comfortable viewing position the forward tilt angle of the monitor should not exceed 5 degrees Connecting the Display Using the Computer NOTE m This is a simplified representation of the rear view m This rear view represents a general model your display may differ from the view as shown 1 Connect D sub RGB Analog Cable PC Connect D sub RGB Analog Cable Mac Analog signal X PORT D sub CH E22 Hit Wall outlet type p MAC lt u gh le 3 Mac adapter This item must be purchased separately For Apple Macintosh use a separate plug adapter is needed to change the 15 pin high density 3 row D sub VGA connector on the supplied cable to a 15 pin 2 row connector 2 Press l button on the front switch panel to turn the power on When monitor power is turned on the Self Image Setting Function is executed automatically ead E wa NOTE Self Image Setting Function This function provides the user with op
5. Tilt 5 20 AC 100 240V 50 60Hz 0 8A Operating Conditions Temperature 10 C to 35 C Humidity 10 to 80 non Condensing Storage Conditions Temperature 20 C to 60 C Humidity 5 to 90 non Condensing Attached Detached O Wall outlet type a Information in this document is subject to change without notice Specifications Display Sync Input Video Input Resolution Plug amp Play Power Consumption Dimensions amp Weight Tilt Range Power Input Environmental Conditions Stand Base Power cord NOTE N1941W N1941WP N1941WE 18 51 inches 47 0 cm Flat Panel Active matrix TFT LCD Anti Glare coating Visible diagonal size 47 0 cm 0 30 0 30 mm pixel pitch D SUB Horizontal Freg 30 66 kHz Automatic Vertical Freq 57 63 Hz Automatic D SUB support 60Hz only except Dos mode X PORT 1440 x 900 60Hz 1280 x 720 60Hz 1360 x 768 60Hz 800 x 600 72Hz 1024 x 768 60HZz D SUB Signal Input 15 pin D Sub Connector Input Form RGB Analog 0 7 Vp p 75 ohm X PORT Signal Input X PORT Connector Input Form X PORT Signal Max VESA 1360 x 768 60 Hz Recommend VESA 1360 x 768 60 Hz DDC 2B Only for D SUB Input On Mode 23W Typ Sleep Mode lt 1W Off Mode lt 1 W With Stand Without Stand Width 44 84 cm 17 65 inches 44 84 cm 17 65 inches Height 35 79 cm 14 09 inches 27 80 cm 10 94 inches Depth 19 84 cm 7 81 inches 5 76cm 2 27 inches Net 3 1 kg
6. proper operation of all safeguards incorporated in this display observe the following basic rules for its installation use and servicing On Safety Use only the power cord supplied with the unit In case you use another power cord make sure that it is certified by the applicable national standards if not being provided by the supplier If the power cable is faulty in any way please contact the manufacturer or the nearest authorized repair service provider for a replacement The power supply cord is used as the main disconnection device Ensure that the socket outlet is easily accessible after installation Operate the display only from a power source indicated in the specifications of this manual or listed on the display If you are not sure what type of power supply you have in your home consult with your dealer Overloaded AC outlets and extension cords are dangerous So are frayed power cords and broken plugs They may result in a shock or fire hazard Call your service technician for replacement As long as this unit is connected to the AC wall outlet it is not disconnected from the AC power source even if the unit is turned off Do not Open the Display a There are no user serviceable components inside There are Dangerous High Voltages inside even when the power is OFF a Contact your dealer if the display is not operating properly To Avoid Personal Injury Do not place the display on a sloping shelf unless prope
7. when Wall mount plate is purchased LG recommends that wall mounting be performed by a qualified professional installer Kensington Security Slot Connected to a locking cable that can be purchased separately at most computer stores Digitally yourSsaes La
8. 6 89 Ibs Tilt 5 20 AC 100 240V 50 60Hz 0 8A Operating Conditions Temperature 10 C to 35 C Humidity 10 to 80 non Condensing Storage Conditions Temperature 20 C to 60 C Humidity 5 to 90 non Condensing Attached Detached O Wall outlet type a Information in this document is subject to change without notice D SUB Preset Modes Resolution Display Modes Resolution Horizontal Freq kHz Vertical Freq Hz 1 720 x 400 31 468 70 2 640 x 480 31 469 60 3 800 x 600 37 879 60 4 1024 x 768 48 363 60 5 1360 x 768 47 712 60 Recommend Mode X PORT Preset Modes Resolution Display Modes Resolution 1 800 x 600 72HZz 2 1024 x 768 60HZ 3 1280 x 720 60HZ 4 1360 x 768 60HZ 5 1440 x 900 60Hz Recommend Mode Indicator hatOJD LED Color On Mode Blue Sleep Mode Flicker Off Mode Off Installing the Wall mount plate Only for N1941W N1941WP N1941WE This monitor satisfies the specifications of the Wall mount plate or the interchange device 1 Place the monitor with its front facing downward on a soft cloth 2 Separate the stand by pushing the PUSH button eT Good Position Bad Position Warning You can hurt your finger 3 Install the Wall mount plate Wall mount plate Separate purchase This is stand type or wall mount type and is connectable with Wall mount plate Please refer to the installation guide for more details which is provided
9. D Set your own red color levels GREEN Set your own green color levels ia Pao A BLUE Set your own blue color levels Increase s SET Select another sub menu On Screen Display OSD Selection and Adjustment Main menu Sub menu Description POSITION NUE ve a ser HORIZONTAL To move image left and right VERTICAL To move image up and down VERTICAL a 50 MENU Exit 7 T Decrease m Increase SET Select another sub menu TRACKING z TRACKING TRACKING UR vE aE ser CLOCK To minimize any vertical bars or stripes y visible on the screen background The horizontal screen size will also change z a Om H 50 7 N PHASE To adjust the focus of the display ry This item allows you to remove any horizontal noise and clear or sharpen the image of characters MENU Exit y Decrease Increase fth SET Select another SHARPNESS To adjust the clearness of the screen sub menu On Screen Display OSD Selection and Adjustment Main menu SETUP aLa BOs OSD POSITION 7 HORIZONTAL Om 1G E VERTICAL TE B Omm JH F h X PORT we 1280 x 1024 60HZ POWER INDICATOR 4 3 IN WIDE FACTORY RESET X PORT 1280 x 1024 60HZ MENU Exit Y Adjust Adjust s SET Select ano
10. Do you see an OUT OF This message appears when the signal from the RANGE message on PC video card is out of horizontal or vertical the screen frequency range of the display See the Specifications section of this manual and configure your display again Do you see a CHECK This message appears when the signal cable SIGNAL CABLE between your PC and your display is not message on the connected Check the signal cable and try again screen Do you see a OSD LOCKED message on the screen Do you see OSD e You can secure the current control settings LOCKED when you so that they cannot be inadvertently changed push MENU button You can unlock the OSD controls at any time by pushing the MENU button for several seconds the message OSD UNLOCKED will appear Troubleshooting Display image is incorrect Display Position is e Press the AUTO SET button to automatically incorrect adjust your display image to the ideal setting lf the results are unsatisfactory adjust the image position using the H position and V position icon in the on screen display On the screen e Press the AUTO SET button to automatically background vertical adjust your display image to the ideal setting bars or stripes are lf the results are unsatisfactory decrease the visible vertical bars or stripes using the CLOCK icon in the on screen display Any horizontal noise e Press the AUTO SET but
11. User s Guide CC Network Monitor N1642W N1642WP N1941W N1941WP N1941WE Make sure to read the Important Precautions before using the product Keep the User s Guide CD in an accessible place for future reference See the label attached on the product and give the information to your dealer when you ask for service With LG Network Monitor some PC programs may not be compatible or need to be modified due to different kind of operation Please check the compatibility in advance before purchasing or installing the software LG do not have any kind of legal liability on this matter La Accessories Thank for selecting LGE products Please make sure the following items are included with your monitor If any items are missing contact your dealer User s Guide Cards 15 pin D Sub Signal Cable To set it up this signal cable may be attached to this product before shipping out Power Cord Lan cable and EMI Core Depending on the country These items are not included for all models IMPORTANT This accessories may look different from those shown here a User must use shielded signal interface cables D sub 15 pin cable LAN cable with ferrite cores to maintain standard compliance for the product Important Precautions This unit has been engineered and manufactured to ensure your personal safety however improper use may result in potential electrical shock or fire hazards In order to allow the
12. d to the PC a Applications that require other than 16 bit color quality and the set resolution are not supported a AUTO SET Function When you encounter problems such as blurry screen blurred letters screen flicker or titled screen while using the device or after changing screen resolution press the AUTO SET function button to improve resolution 2 Press l button on the front switch panel to turn the power on Connecting the Display NOTE a LAN Cable For the LAN cable it is recommended to use SFTP recommend 6m max 10m provided by LG Image quality and some functionality may be degraded if a different LAN cable is used To achieve good image quality avoid using UTP and STP cables You must use a direct LAN cable not a crossover one S Both connections should be same i colors gt Do not connect any kind of network devices Core The ferrite core can be used to reduce electromagnetic waves when connecting a LAN cable As shown in the image below fit the ferrite core to the LAN cable The ferrite core needs to be separated from the mold by 5 centimeters You can purchase SFTP recommend 6m max 10m LAN cables and cores through LG additionally 50 10mm JL Jae 50 10mm ne lt Connecting the Display Connecting to a X550 port using a LAN cable Notice a Turning the power off while booting the PC may damage the product a Turing the power off whil
13. e booting the PC may cause it to operate incorrectly a If the mouse is connected using a USB device and is not detected disconnect and connect it again a If you reconnect a peripheral device such as a keyboard mouse or LAN cable while the PC is in operation the device may not work properly Make sure that the power is turned off when disconnecting connecting a peripheral device a Making both ends of LAN cable to across the coil two times before connect to network monitor and PC PC spec a The host PC operating system can be Windows Server 2003 R2 SP2 Standard or Enterprise Edition 32 bit Notice To achieve the best PC performance up to six users are recommended for one PC If there are seven or more users performance may be degraded depending on the environment and the PC s specifications Check if the PC supports Windows Server 2003 before purchasing it a A host PC should have the following specifications 1 Minimum CPU Dual core processor at 3 0 GHz or higher i e Intel Core 2 Duo or AMD Athlon X2 RAM 2 GB of system memory or higher 2 Recommend CPU Quad core processor at 2 66 GHz or higher i e Intel Core 2 Quad or AMD Phenom X4 RAM 4 GB of system memory 3 Internet access speed may be different depending on the network environment Restrictions a Using this network monitor for the following purposes may cause screen disruption or slower PC operation 1 Video Moving picture 2 Games Co
14. e center for repair Avoid high temperatures and humidity Important Precautions On Cleaning Unplug the display before cleaning the face of the display screen a Use a slightly damp not wet cloth Do not use an aerosol directly on the display screen because over spraying may cause electrical shock a When cleaning the product unplug the power cord and scrub gently with a soft cloth to prevent scratching Do not clean with a wet cloth or spray water or other liquids directly onto the product An electric shock may occur Do not use chemicals such as benzene paint thinners or alcohol a Spray water onto a soft cloth 2 to 4 times and use it to clean the front frame wipe in one direction only Too much moisture may cause staining On Repacking a Do not throw away the carton and packing materials They make an ideal container in which to transport the unit When shipping the unit to another location repack it in its original material On Disposal Only Hg lamp used LCD Monitor a The fluorescent lamp used in this product contains a small amount of mercury a Do not dispose of this product with general household waste a Disposal of this product must be carried out in accordance to the regulations of your local authority Connecting the Display a Before setting up the monitor ensure that the power to the monitor the computer system and other attached devices is tur
15. lor setting a Image quality may vary depending on the X550 card so it is recommended to execute White Balance when using the product as a network monitor after connecting a LAN cable for the first time Refer to A18 for more information on White Balance If you use the monitor with a X PORT input image quality and resolution may be poorer than with a D sub input Only 16 bit color is supported for X PORT input Control Panel Functions Front Panel Controls MUTE MENU SOURCE VOLUME AUTO SET va Control Function e X PORT This menu is available use this button to switch the sound on or off Q VOLUME Y ser t MENUS Q VOLUME Y lt mute off gt lt mute on gt e D sub This menu is not available THIS MENU IS NOT AVAILABLE 2 MENU Button Use this button to enter or exit the On Screen Display OSD LOCKED UNLOCKED This function allows you to lock the current control settings so that they cannot be inadvertently changed Press and hold the MENU button for several seconds The message OSD LOCKED should appear You can unlock the OSD controls at any time by pushing the MENU button for several seconds The message OSD UNLOCKED should appear Control Panel Functions Control v source A VOLUME AUTO SET Button PROCESSING AUTO IMAGE ADJUSTMENT 5 Power Button Power Indicator
16. ned off Connecting the stand 1 Place the monitor with its front facing downward on a soft cloth 2 Assemble the Stand Body into the product in the correct direction as shown in the picture Make sure you push it until you hear it click Hinge Body Stand Body 3 Assemble the Stand Base Front Rear into the Stand Body in the correct direction Stand Body Stand Base 4 Tie down the base lock to perpendicularity direction 5 Once assembled take the monitor up carefully and face the front side Important This illustration depicts the general model of connection Your monitor may differ from the items shown in the picture Do not carry the product upside down holding only the stand base The product may fall and get damaged or injure your foot Connecting the Display Disassembling the stand 1 Puta cushion or soft cloth on a flat 2 Place the monitor face down on the surface cushion or soft cloth 3 Change your lock on the product as it follows and turn it in the arrow direction If you can t release the stand base even the locking knob is at a release position Please push the indicated knob down and retry it 4 Pull out the stand to remove Connecting the Display 5 Pushing the PUSH button take the stand base from stand body Warning You can hurt your finger Good Position Bad Position Before setting up the monitor ensure that the power to the monitor
17. om ventilation slots by placing the display on a bed sofa rug etc Place the display in a built in enclosure unless proper ventilation is provided a Cover the openings with cloth or other material a Place the display near or over a radiator or heat source Do not rub or strike the Active Matrix LCD with anything hard as this may scratch mar or damage the Active Matrix LCD permanently Do not press the LCD screen with your finger for a long time as this may cause some afterimages Some dot defects may appear as Red Green or Blue spots on the screen However this will have no impact or effect on the display performance If possible use the recommended resolution to obtain the best image quality for your LCD display If used under any mode except the recommended resolution some scaled or processed images may appear on the screen However this is characteristic of the fixed resolution LCD panel Leaving a fixed image on the screen for a long time may cause damage to the screen and cause image burn in Make sure to use a screen saver on the product Burn in and related problems are not covered by the warranty on this product Do not shock or scratch the front and sides of the screen with metallic objects Otherwise it may cause damage to the screen Make sure the panel faces forward and hold it with both hands to move If you drop the product the damaged product can cause electric shock or fire Contact an authorized the servic
18. pending on the model A14 A19 D On Screen Display OSD Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system Listed below are the icons icon names and icon descriptions of the all items shown on the Menu Press the MENU Button then the main menu of the OSD appears PICTURE COLOR POSITION Main Menu TRACKING SETUR 55 ro a MENU gt Exit Y 4 Adjust Decrease Increase a SET Enter Select another sub menu Restart to select sub menu Button Tip Menu Name PICTURE MENUS wle SET CONTRAST leans 0 Om 1H 50 Sub menus NOTE OSD On Screen Display menu languages on the monitor may differ from the manual On Screen Display OSD Selection and Adjustment Main menu Sub menu Description PICTURE PICTURE Enu s BRIGHTNESS To adjust the brightness of the screen CONTRAST To adjust the contrast of the screen CONTRAST 9 Om 1 50 GAMMA Set your own gamma value 50 0 50 On the monitor high gamma values display whitish images and low gamma values display blackish images VY Decrease A Increase SET Select another sub menu PRESET Select the screen color e SRGB Set the screen color to fit the SRGB standard color specification e 6500K Slightly reddish white e 9300K Slightly bluish white RE
19. rly secured a Use only a stand recommended by the manufacturer Do not drop an object on or apply impact to the product Do not throw any toys or objects on the product screen It can cause injury to human problem to product and damage the display To Prevent Fire or Hazards a Always turn the display OFF if you leave the room for more than a short period of time Never leave the display ON when leaving the house a Keep children from dropping or pushing objects into the display s cabinet openings Some internal parts carry hazardous voltages Do not add accessories that have not been designed for this display a When the display is to be left unattended for an extended period of time unplug it from the wall outlet a In the presence of thunder and lightning never touch the power cord and signal cable because it can be very dangerous It can cause electric shock Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord and do not place the display where the power cord is subject to damage Do not use this display near water such as near a bathtub washbowl kitchen sink laundry tub in a wet basement or near a swimming pool Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation If these openings are blocked built up heat can cause failures which may result in a fire hazard Therefore NEVER a Block the bott
20. stabilize for at least 30 minutes before making image adjustments To make adjustments in the On Screen Display follow these steps MENU gt V A AUTO SET V A MENU il 2 3 4l Press the MENU Button then the main menu of the OSD appears To access a control use the V or amp Buttons When the icon you want becomes highlighted press the AUTO SET Button Use the V 4Buttons to adjust the image to the desired level Use the AUTO SET Button to select other sub menu items Push the MENU Button once to return to the main menu to select another function Push the MENU Button twice to exit from the OSD On Screen Display OSD Selection and Adjustment The following table indicates all the On Screen Display control adjustment and setting menus Adjustable A D SUB Input X X PORT Input Main menu PICTURE COLOR Sub menu Reference paomess Tole To adjust the brightness CONTRAST CONTRAST contrast and gamma of the GAMMA GAMMA AMMA screen To customize the color of PRESET gt 6500K the screen 9300K POSITION OO NOTE To adjust the position of the VERTICAL o o sen 0 prise EHE Tomo telat a OC anava ___ LANGUAGE jo HORIZONTAL E sbi pia POSITION VERTICAL environment WHITE BALANCE o POWER INDICATOR 4 3 IN WIDE o FACTORY RESET jo MOVIE To select or customize INTERNET desired image settings USER a The order of icons may differ de
21. ther sub menu Sub menu LANGUAGE OSD POSITION WHITE BALANCE POWER INDICATOR 4 3 IN WIDE FACTORY RESET Description To choose the language in which the control names are displayed To adjust position of the OSD window on the screen If the output of the video card is different from the required specifications the color level may deteriorate due to video signal distortion Using this function the signal level is adjusted to fit into the standard output level of the video card in order to provide the optimal image Activate this function when white and black colors are present in the screen Use this function to set the power indicator on the front side of the monitor to ON or OFF If you set OFF it will go off If you set ON at any time the power indicator will automatically be turned on Use this function to select the image size of the screen e WIDE Switch to full screen mode according to input image signal e 4 3 Change the image signal ratio into 4 3 Restore all factory default settings except LANGUAGE Press the wW A buttons to reset immediately If this does not improve the screen image restore the factory default settings If necessary perform the white balance function again This function will be enabled only when the input signal is a D sub or X PORT input signal On Screen Display OSD Selection and Adjustment Main menu Sub menu Description
22. timal display settings When the user connects the monitor for the first time this function automatically adjusts the display to optimal settings for individual input signals AUTO SET Function When you encounter problems such as blurry screen blurred letters screen flicker or tilted screen while using the device or after changing screen resolution press the AUTO SET function button to improve resolution Connecting the Display Using the Monitor 1 Make sure to turn off the computer and product Connect the cable as below sketch map form to Connect peripheral devices Connect LAN Cable X550 port Analog signal X PORT D sub CH NE WU IMMA Wall outlet type Keyboard Mouse Input LAN cable should be connected before boo ting PC This item must Make sure to connect X550 be purchased separately port not LAN port of PC 2N oo aN X550 port lt a 1 M e Up to 5 ports are supported per X550 PCI Card A Up to 5 ports can be connected if necessary These items are not included for all models Headphone Earphone Input Automatically mutes the speaker volume when the headphones are plugged in m When you use the monitor speaker via the X PORT tum the PC volume up to the highest ary level and adjust the monitor volume a tis recommended to use a PS 2 type keyboard mouse To use the monitor keyboard mouse properly it must be connecte
23. ton to automatically appearing in any adjust your display image to the ideal setting image or characters If the results are unsatisfactory decrease the are not clearly horizontal bars using the PHASE icon in the on portrayed screen display e Check Control Panel gt Display gt Settings and adjust the display to the recommended resolution or adjust the display image to the ideal setting Set the color setting higher than 24 bits true color Only for D SUB input Important a Check Control Panel gt Display gt Settings and see if the frequency or the resolution were changed If yes readjust the video card to the recommend resolution Only for D SUB input a The setting method can differ by computer and O S Operation System and resolution mentioned above may not be supported by the video card performance In this case please ask to the computer or the video card manufacturer Only for D SUB input a f the recommended resolution optimal resolution is not selected letters may be blurred and the screen may be dimmed truncated or biased Make sure to select the recommend resolution O Troubleshooting Display image is incorrect The screen color is e Check if the signal cable is properly connected mono or abnormal and use a screwdriver to fasten if necessary e Make sure the video card is properly inserted in the slot e Set the color setting higher than 24 bits true color at Control Panel
Download Pdf Manuals
Related Search