Siig Serial ATA PCI
Contents
1. S Serial ATA PCI Quick Installation Guide Introducing the Serial ATA PCI The Serial ATA PCI is an ultra high speed dual channel Serial ATA controller board for use in Pentium class computers It achieves burst data transfer rates up to 150MB s 1 5Gb s and supports various brand of hard disk drives with capacities greater that 137GB Features and Benefits Add up to two high speed SATA hard drives New Serial ATA cable easier to install amp provides better air circulation Compliant with Serial ATA 1 0 specification Compliant with PCI 2 3 specification Supports data transfer rate up to 1 5Gb s 150MB s Two independent bus master DMA channels with 256 byte FIFOs per channel for host reads and writes Breaks the 137GB barrier Works with various brands of large capacity Serial ATA hard disk drives System Requirements Pentium or equivalent PC with an available PCI slot Windows 98SE ME NT4 0 2000 XP 32 64 bit Server 2003 amp 2008 32 64 bit Vista 32 64 bit 04 0265F 1 Package Contents e Serial ATA PCI adapter e DriverCD e Serial ATA cable e Serial ATA power cable e Quick installation guide Board Layout CN1 Serial ATA connector Figure 1 Serial ATA PCI Board Layout Hardware Installation General instructions for installing the card are provided below Since the design of computer cases and motherboards vary refer to your computer s reference manual for fur2. Windows installation At the Windows Setup screen press F6 to install the driver Insert the floppy disk you made above Press S then press Enter Select Silicon Image Sil 3512 that matches your system processor then press Enter Press Enter to continue and follow the on screen instructions to complete the installation For Existing Windows XP 2003 Installation 1 2 Install the board and boot up Windows Atthe Found New Hardware Wizard select No not at this time then click Next Insert the driver CD select Install the software automatically Recommended and click Next Click Finish and restart Windows to complete the installation To Verify Windows 2000 XP 2003 Installation 1 Right click My Computer and click Manage 2 Select Device Manager 3 Double click SCSI and RAID Controllers Silicon Image Sil 3512 Controller should be displayed Windows Vista 32 bit For New Windows Vista Installation 1 Install the board and follow Microsoft procedures to install Windows Vista accordingly 2 At the Where do you want to install Windows screen click Load Driver 3 Insert the driver CD then click OK 4 Select Silicon Image Sil SATALink Controller then click Next 5 Follow the on screen instructions to complete the Windows Vista installation For Existing Windows Vista Installation 1 At the Found New Hardware Wizard click Locate and install driver software recommended 2 Clic
3. indows NT4 0 For New Windows NT4 0 Installation A new installation of Windows NT4 0 requires a floppy disk for the driver installation To make this floppy disk copy the contents of the NT4 folder found on the driver CD onto a blank floppy disk then follow the directions below 1 Install the board and follow Microsoft procedures to install Windows NT4 0 accordingly 2 At the Windows NT Setup screen press F6 to specify and add the driver 3 Press S select Other then press Enter 4 Insert the driver diskette then press Enter 5 Select Silicon Image for Windows NT 4 0 and 2000 and press Enter 6 Press Enter to continue then follow the on screen instructions to complete Windows NT4 0 installation For Existing Windows NT4 0 Installation 1 2 Install the board and boot up Windows NT4 0 Double click My Computer Control Panel SCSI Adapters then click the Drivers tab Click Add then click Have Disk Insert the driver CD type D NT4 then click OK Change D to match the drive letter of your CD ROM Highlight Silicon Image in the left column then select Silicon Image Sil SATALink Controller and click OK Click OK remove the driver CD and restart NT4 0 to complete the installation To Verify Windows NT4 0 Installation 1 Double click My Computer Control Panel SCSI Adapters Highlight Silicon Image Controller from SCSI Adapters listing and click Properties A message This device
4. is working properly is displayed in the dialog box when the driver is correctly installed Windows 2000 For New Windows 2000 Installation A new installation of Windows 2000 requires a floppy disk for the driver installation To make this floppy disk copy the contents of the Floppy folder found on the driver CD onto a blank floppy disk then follow the directions below 1 Install the board and follow Microsoft procedures to install Windows 2000 accordingly Restart your system when prompted during Windows installation At the Windows 2000 Setup screen press F6 to install the driver Insert the driver diskette Press S then press Enter Select Silicon Image Sil Controller and press Enter Press Enter to continue and follow on screen instructions to complete the installation For Existing Windows 2000 Installation 1 2 3 Install the board and boot up Windows 2000 At the Found New Hardware Wizard click Next Select Search for a suitable driver for my device recommended and click Next 4 Insertthe driver CD check CD ROM drives uncheck the other boxes and click Next Click Next again to continue 5 Click Finish remove the driver CD and restart Windows to complete the installation Windows XP Server 2003 32 bit For New Windows XP Server 2003 Installation A new installation of Windows XP Server 2003 requires a floppy disk for the driver installation To make this floppy disk copy the co
5. k Continue insert the driver CD click Next 3 Click Close to complete the installation Windows Vista 64 bit For New Windows Vista 64 bit Installation 1 Install the board and follow Microsoft procedures to install Windows accordingly 2 At Where do yo want to install Windows screen click Load Drivers 3 Insert the driver CD click Browse 11 4 Click on the Plus sign next to the CD ROM drive then double click the 64bit folder 5 Highlight AMD64 for 64 bit extended processors or IA64 for 64 bit Intel Itanium processors then click Ok 6 Select Silicon Image SATALink Controller then press Next 7 Follow the on screen instructions to complete the installation For Existing Windows Vista 64 bit Installation 1 Install the board and boot up Windows 2 Atthe Found New Hardware Wizard select Locate and install driver software recommended click Continue 3 Insert the driver CD click Next 4 Click Close to complete the installation To Verify Windows Vista Installation 1 Right click My Computer and click Manage 2 Click Continue click Device Manager 3 Double click Storage controllers Silicon Image Sil Controller should be displayed Windows Server 2008 32 bit New Windows 2008 Installation 1 Install the board and follow Microsoft procedures to install Windows accordingly 2 At Where do you want to install Windows click Load Driver 3 Insert driver CD then click Br
6. ntents of the Floppy folder found on the driver CD onto a blank floppy disk then follow the directions below 1 Install the board and follow Microsoft procedures to install Windows accordingly 2 Restart your system if prompted by Windows installation 3 Atthe Windows Setup screen press F6 to install the driver 4 Insert the driver diskette Press S then press Enter 5 Select Silicon Image Sil Controller and press Enter 6 Press Enter to continue and follow the on screen instructions to complete the installation For Existing Windows XP Server 2003 Installation 1 Install the board and boot up Windows 2 At the Found New Hardware Wizard XP w SP1 or earlier Server 2003 continue to step 3 XP w SP2 or later Server 2003 w SP1 or later select No not at this time then click Next 3 Insert the driver CD select Install the software automatically Recommended and click Next 4 Click Finish and restart Windows to complete the installation Windows XP Server 2003 64 bit For New Windows XP 2003 Installation A new installation of Windows XP 64 bit Server 2003 64 bit requires a floppy disk for the driver installation To make this floppy disk copy the contents of the 64bit folder found on the driver CD onto a blank floppy disk then follow the directions below 1 Install the board and follow Microsoft procedures to install Windows accordingly Restart your system when prompted by
7. owse 4 Click CD Drive Drivers then click OK Select Silicon Image Sil 3512 SATALink Controller then click OK Follow on screen instructions to complete Windows Server 2008 installation Existing Windows 2008 Installation 1 2 Install the board and boot up Windows At the Found New Hardware Wizard select Locate and install driver software Recommended then click Don t search online Insert the driver CD The driver will install automatically Click Close Remove the driver CD and restart your Windows to complete the installation Windows Server 2008 64 bit New Windows 2008 Installation 1 Install the board and follow Microsoft procedures to install Windows accordingly At Where do you want to install Windows click Load Driver Insert driver CD then click Browse Double click CD Drive D change D to match your CD ROM drive letter Double click 64bit folder highlight AMD64 for 64 bit extended processors or IA64 for 64 bit Intel Itanium processors then click Ok Select Silicon Image Sil 3512 SATALink Controller then click Next Follow on screen instructions to complete Windows Server 2008 installation Existing Windows 2008 Installation 1 Install the board and boot up Windows 2 Atthe Found New Hardware Wizard select Locate and install driver software Recommended then click Don t search online 3 Insert the driver CD The driver will install automatically 4 Click Clo
8. rosoft procedures to install Windows ME accordingly 2 Once Windows has been installed right click My Computer then click Properties Select Device Manager tab 3 Double click PCI Mass Storage Controller listed under Other Devices 4 Select Driver tab then click Update Driver button 5 Insert the driver CD select Specify the location of the driver Advanced then click Next Check Specify a location uncheck the other box type D ME click Next Change D to match the drive letter of your CD ROM Click Next then click Finish Remove the driver CD and restart Windows to complete the installation For Existing Windows ME Installation 1 2 Install the board and boot up Windows ME Atthe Add New Hardware Wizard insert the driver CD Select Specify the location of the driver Advanced then click Next Check Specify a location uncheck the other box type D ME click Next Change D to match the drive letter of your CD ROM Click Next then click Finish Remove the driver CD and restart Windows to complete the installation To Verify Windows 98SE ME Installation 1 Right click My Computer then click Properties Select Device Manager tab Double click SCSI controllers Silicon Image Sil Controller should be listed Double click Silicon Image Sil Controller and click Properties A message This device is working properly is displayed in the dialog box when the driver is correctly installed W
9. se 5 Remove the driver CD and restart your Windows to complete the installation Verify Server 2008 Installation 1 Right click Computer click Manage double click Diagnostics click Device Manager 2 Double click Storage controllers Silicon Image Sil Controller should be displayed Bios Configuration The Serial ATA PCI BIOS will appear everytime your system starts up If the bios doesn t show please install your controller in another PCI slot During this Post process the bios will show up and indicate the devices attached to it Technical Support and Warranty QUESTIONS SIIG s Online Support has answers Simply visit our web site at www siig com and click Support Our online support database is updated daily with new drivers and solutions Answers to your questions could be just a few clicks away Youcanalso submit questions online and a technical support analysts will promptly respond SG offers a lifetime manufacturer warranty with this product Please see our web site for more warranty details If you encounter any problems with this product please follow the procedures below A If it is within the store s return policy period please return the product to the store where you purchased from B If your purchase has passed the store s return policy period please follow these steps to have the product repaired or replaced Step 1 Submit your RMA request Go to wwwssiig com click Support then RMA to s
10. ther information if needed Static Electricity Discharge may permanently damage your system Discharge any static electricity build up in your body by touching your computer case for a few seconds Avoid any contact with internal parts and handle cards only by their external edges 2 e Turn OFF the power to your computer and any other connected peripheral devices Unplug the power cord from the back of the computer Remove the computer cover Remove the slot bracket from an available PCI slot To install the card carefully align the card bus connector to the selected PCI slot on the motherboard Push the board down firmly but gently until it is well seated Replace the slot bracket holding screw to secure the card Device Connection The Serial ATA PCIis a dual channel Serial ATA controller that supports up to two Serial ATA hard disk drives If you plan to use the second Serial ATA channel you will need to purchase another Serial ATA cable 1 2 Install hard disk drive s in chassis Connect the Serial ATA hard disk drive to thesystem power supply using the Serial ATA power cable Connect one end of the Serial ATA cable to the hard disk drive Serial ATA cable Serial ATA power cable Figure 2 Hard disk drive connecrions Attach the other end of the Serial ATA cable to the Serial ATA connector on the Serial ATA PCI Serial ATA cable Figure 3 Connecting the Serial ATA cable Follo
11. ubmit a request to SIG RMA If the product is determined to be defective an RMA number will be issued Step 2 After obtaining an RMA number ship the product e Properly pack the product for shipping All software cable s and any other accessories that came with the original package must be included e Clearly write your RMA number on the top of the returned package SIG will refuse to accept any shipping package and will not be responsible for a product returned without an RMA number posted on the outside of the shipping carton e Youare responsible for the cost of shipping Ship the product to the following address SIIG Inc 6078 Stewart Avenue Fremont CA 94538 3152 USA RMA e SIIG will ship the repaired or replaced product via Ground in the U S and International Economy outside of the U S at no cost to the customer About SIIG Inc Founded in1985 SHG Inc isa leading computer upgrade manufacturer of 1 Oconnectivity products including PCI amp ISA serialand parallel ports USB Serial ATA amp UltraATA controllers FireWire 1394a b networking sound cards and other accessories SIIG is the premier one stop source of upgrades SIIG products offer comprehensive user manuals many user friendly features and are backed by an extensive manufacturer warranty High quality control standards are evident by the overall ease of installation and compatibility of our products as well as one of the lowest defective ret
12. urn rates in the industry SIIG products can be found in computer retail stores mail order catalogs through major distributors system integrators and VARs in the Americas and the UK and through e commerce sites PRODUCT NAME Serial ATA PCI FCC RULES TESTED TO COMPLY WITH FCC PART 15 CLASS B OPERATING ENVIRONMENT FOR HOME OR OFFICE USE FCC COMPLIANCESTATEMENT This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE SIG Inc 6078 Stewart Avenue Fremont CA 94538 3152 USA Ph 510 657 8688 Serial ATA PCTis a trademark of SHG Inc SIIG and the SHG logo are registered trademarks of SUG Inc Microsoft Windows and Windows Vista are either registered trademarks or trademarks of Microsoft Corporationin the United States and or other countries Pentiumisaregistered trademark of Intel Corporation Other names used in this publication are for identification only and may be trademarks of their respective companies March 2009 Copyright 2009 by SIIG Inc All rights reserved
13. w the same instructions when connecting a second hard drive Device connection is now complete Replace the computer cover and reconnect the power cord Driver Installation This section provides information on how to install the Serial ATA PCI drivers Windows 98SE For New Windows 98SE Installation 1 Install the board and follow Microsoft procedures to install Windows 98SE accordingly 2 Once Windows has been installed right click My Computer and click Properties Select Device Manager tab 3 Double click PCI Mass Storage Controller listed under Other Devices 4 Select Driver tab then click Update Driver button 5 Insert the driver CD and click Next Select Search for a better driver then click Next Check Specify a location uncheck the other boxes then click Next Click Next then click Finish Remove the driver CD and restart Windows to complete the installation For Existing Windows 98SE Installation 1 Install the board and boot up Windows 2 Atthe Add New Hardware Wizard click Next 3 Select Search for the best driver for your device and click Next 4 Insert the driver CD check Specify a location uncheck the other boxes type D 98SE then click Next Change D to match the drive letter of your CD ROM 5 Click Next then Finish 6 Remove the driver CD and restart Windows to complete the installation Windows ME For New Windows ME Installation 1 Install the board and follow Mic
Download Pdf Manuals
Related Search