Philips 3000 series 32PFL3605 32" Full HD 3D compatibility
Contents
1. USB Jum EN 27 Connect a computer Before you connect a computer to the TV Set the screen refresh rate on your computer to 60Hz Select a supported screen resolution on your computer Connect a computer with one of the following connectors Connections via DVI or VGA require an additional audio cable HDMI cable AUDIO IN LEFT RIGHT VGA DVI G 28 EN HDMI cable and HDMI DVI adaptor AUDIO IN LEFT RIGHT VGA DVI VGA cable AUDIO IN LEFT RIGHT VGA DVI Use Philips EasyLink Your TV supports Philips EasyLink which uses the HDMI CEC Consumer Electronics Control protocol EasyLink compliant devices that are connected through HDMI connectors can be controlled by a single remote control Note The EasyLink compliant device must be switched on and selected as the source Philips does not guarantee 10076 interoperability with all HDMI CEC devices Use one touch play 1 After enabling EasyLink press play on your device L gt TheTV automatically switches to the correct source Use one touch standby 1 Press Standby On on the TV s or device s remote control L gt The TV and all connected HDMI devices switch to standby EasyLink features One touch play When you connect your TV to devices that support one touch play you can control yo2. L COO ODD COO DOD COO ODD COO DOD AUDIO OUT D TV ANTENNA Signal input from an antenna cable or satellite 750 Ir TV ANTENNA Qo EXT 1 and EXT 2 CVBS and RGB Analogue audio and video input from analogue or digital devices such as DVD players or game consoles EXT I RGB CYBS m Ho ou mu mu mu mu mmj mu mu OO EREEENEEEN EN 25 English 3 EXT 3 Y Pb Pr and AUDIO L R 6 HDMI 1 Analogue audio and video input from Digital audio and video input from high analogue or digital devices such as DVD definition digital devices such as Blu ray players or game consoles players HDMI I Connections via DVI or VGA require an additional audio cable see Connect a computer on page 28 PC IN VGA and AUDIO IN Audio and video input from a computer AUDIO IN LEFT RIGHT VGA DVI 5 SERV U For use by service personnel only 26 EN 2 VIDEO Composite video input from analogu devices such as VCRs Side connector o English 3 HDMI Digital audio and video input from high definition digital devices such as Blu ray players i HDMI e gt Biuray Disc D AUDIO L R Audio input from analogue devices connected to VIDEO 4 USB L AUDIO R VHS Data input from USB storage devices
3. Press amp MENU 1 2 Press Av to select Setup gt Installation gt Channel installation gt Analogue Manual The Analogue Manual menu appears Select System then press OK to enter Press AY to select your country or region Press OK to confirm Press amp MENU to exit DU KRW Step 2 Select your country Select the country where you are installing the TV The available channels for the country are installed on the TV 1 Press MENU 2 Select Setup gt Installation gt Channel installation gt Channel assistant The Channel assistant menu appears Select Yes then press OK to enter 4 Press AY to select your country then press P to go to the next step 22 EN Step 2 Search and store new TV channels 1 Pres amp MENU 2 Press AVP to select Setup gt Installation gt Channel installation gt Analogue Manual The Analogue Manual menu appears J Press Av to select Search then press gt to enter 4 Press Numeric buttons to manually enter the three digit frequency 10 Press OK to begin search L Ifa channel is unavailable at the selected frequency the system searches for the next available channel Press BACK when the new channel is found Press AY to select Store as new channel to store the new channel under a new channel number Press P to enter Store as new channel Select OK then press OK to store th
4. Shetland Islands 2010 2010 11 Yorkshire 2011 Anglia 2011 Central Wales 205 2009 10 London 2012 Meridian 2012 West Country 2 PHILIPS 2010 Koninklijke Philips Electronics N V All rights reserved
5. Philips continuously tries to improve its products and we recommend that you update the TV software when updates are available Check www philips com support for availability Check the current software version 1 Pres amp MENU 2 Press ava to select Setup gt Software update gt Current software L gt The TV displays the current software information Download the software 1 on your PC open a web browser and go o www philips com support 2 Download the latest software upgrade file to your PC 3 Decompress the ZIP file 4 Copy the autorun upg file to the root directory of the USB device Update using a USB device Connect your USB device to the USB port at the side of your TV 1 Ifthe software update screen does not appear automatically select Setup gt Software update gt Local updates 2 Press OK to update the TV software manually 3 Follow the on screen instructions to complete the update Note The TV restarts after the software update is complete 20 EN Change TV preferences Use the preferences menu to customise your TV settings 1 Press amp MENU 2 select Setup gt Installation gt Preferences e Location Optimises TV settings for your location home or shop Volume bar Displays the volume bar when you adjust the volume e EasyLink Enables one touch play and one touch standby between EasyLink compliant devices
6. Ui A WN Select Remove then press OK L gt The selected device is removed from the home menu EN 11 English Change picture and sound settings Change picture and sound settings to suit your preferences You can apply pre defined settings or change settings manually Note When watching TV or using external devices press amp OPTIONS then select Picture and sound for quick access to picture and sound settings Use smart picture Use smart picture to apply pre defined picture settings 1 Press O PICTURE L gt The Smart picture menu appears 2 Press AV to select one of the following settings e Vivid Applies rich and dynamic settings Standard Adjusts picture settings to suit most environments and types of video e Cinema Applies settings for movie viewing Game Applies settings for games Energy saving Applies low energy settings e Natural Applies the best picture quality e Custom Lists customised picture settings 3 Press OK to confirm your choice L gt The selected smart picture setting is applied Manually adjust picture settings 1 Press amp MENU 2 Press AVP to select Setup gt Picture J Press AVP to select the following settings e Smart picture Accesses pre defined smart picture settings Video contrast Adjusts the intensity of video contents keeping backlight unchanged e Contrast Adjus
7. NOUI The device name can be up to six characters Press Aa to change an uppercase letter to a When watching TV press OK to display he channel grid Select the channel to rename Press OPTIONS L gt The channel options menu appears Press AY to select Rename channel hen press OK L gt A text input box appears Press AY 4b to select characters Press OK to confirm each character Select Done then press OK to finish renaming channels Tip long lowercase letter and vice versa 24 EN Rearrange channels After you install channels you can rearrange the order in which they appear 1 2 When watching TV press OK to display he channel grid Press OPTIONS L gt The channel options menu appears Press AY to select Reorder then press OK Select the channel to rearrange then press OK L gt The selected channel is highlighted Press AY 4b to move the highlighted channel to the desired location then press OK Press OPTIONS L gt Done reordering appears on the screen Press OK to confirm Press BACK to exit the channel grid 7 Connect devices This section describes how to connect devices with different connectors Examples are provided in the Quick Start Note You can use different types of connectors to connect a device to your TV Back connector EXT 2 EXT1 CVBS RGB CVBS TV ANTENNA
8. TV lock You are prompted to enter your PIN code J Enter your code using Numeric buttons The TV lock menu appears 4 Press AV to select Lock or Unlock 5 Press OK to confirm Ly All channels and connected devices are locked or unlocked 6 Press amp MENU to exit Note Switch the TV off and on again for the change to take effect f you select Lock you have to enter your code every time you turn on your TV Lock or unlock one or more channels 1 when watching TV press OK to display he channel grid Press AVS to select a channel to lock or unlock Press OPTIONS 2 3 4 Press Av to select Lock channel or Unlock channel 5 For each selection press OK to lock or unlock the channel You are prompted to enter your PIN code 6 Enter your code and press OK L If the channel is locked a lock icon is displayed EN 17 English 7 Repeat the process to lock or unlock more channels Note Switch the TV off and on again for the change to take effect f you access the locked channels by pressing P on the remote control or from the channel grid you are prompted to enter your PIN code View photos and play music from a USB storage device Caution Philips is not responsible if the USB storage device is not supported nor is it responsible for damage or loss of data from the device Use the USB connector t
9. L gt The sleep timer can be set in steps of five minutes If set to zero the sleep timer is switched off 4 Press OK to switch on the sleep timer L gt The TV switches to standby after the specified time Automatically switch the TV on on timer You can switch on the TV from standby to a specific channel at a specified time 1 Press amp MENU 2 Press ava to select Setup gt Features gt On timer 3 Press to enter the On timer menu e Activate Selects how often the TV is switched on Time Sets the time to switch on the TV Programme no Selects the channel or the connected device Press amp MENU to exit A Tip e Select On timer gt Activate gt Off to disable this feature Use TV locks You can prevent your children from watching certain programmes or channels by locking the TV controls Set or change your PIN code 1 Press amp MENU 2 Press AVP to select Setup gt Features gt Set code Change code L gt The Set code Change code menu appears J Enter your code using the Numeric buttons Follow the on screen instructions to create or change your PIN code Tip f you forget your code enter 8888 to override any existing codes Lock or unlock the TV Lock the TV to prevent access to all channels and connected devices 1 Press amp MENU 2 Press ava to select Setup gt Features gt
10. amp MENU L gt The menu screen appears 3 n 3 pe latch TV Add new device Setup 2 Press AYP to select and navigate through one of the following menus e Watch TV Switches back to the aerial source if another source is selected e Add new device Adds new devices to the home menu Setup Accesses menus to change picture sound and other settings Press OK to confirm your choice Press amp MENU to exit A WW Tip After selecting Add new device follow the on screen instructions to select the correct device and connector Rename devices from the home menu After adding a new device to the home menu you can rename it to your preference 1 Press amp MENU 2 Press AVS to select a device to rename J Press OPTIONS L gt The options menu appears 4 Press AV to select Rename device then press OK Atext input box appears Press AVP to select characters Press OK to confirm each character Select Done then press OK to finish renaming devices No UI Note The device name can be up to six characters long Press Aa to change an uppercase letter to a lowercase letter and vice versa Remove devices from the home menu If a device is no longer connected to the TV remove it from the home menu Press amp MENU Press AY4b to select a device to remove Press OPTIONS Press AY to select Remove device then press OK
11. e Pixel Plus Link Overrides the settings of connected devices and uses the settings of the T V Only available if EasyLink is switched on E sticker For shop mode only Sets the location of the e sticker Press AY 4b to select your preference Press OK Press amp MENU to exit Ui 4 w Access decoder channel You can map channels provided through a decoder or descrambler to your TV channel selection In this way you can select these channels by using the RC of your TV The decoder or a descrambler must be connected to EXT1 SCART Set decoder channel Map channels from a decoder or descrambler Press amp MENU Select Setup gt Installation gt Decoder Press to enter Decoder menu Press AY to select Channel then press gt to enter Ui A w N Select one channel to map to the decoder descrambler channel and press OK to confirm Select Status then press to enter Select EXT 1 SCART the connector used by the decoder descrambler Press OK Press MENU to exit Oo NO Note Select None if you do not want to map to the decoder descrambler channel Start a TV demo You can use demonstrations to better understand the features of your TV Some demos are not available on certain models Available demos are displayed in the menu list 1 Press DEMO on the remote control 2 Press Av to select a demo and press OK to view it 3 Press
12. technical specifications 3 teletext features 4 menu 4 subpages 5 Table of Pages 5 use 0 timer on timer 7 sleep timer 6 standby 6 transmission 31 33 transporting 4 troubleshooting 33 TV lock lock channels 18 lock connected devices 17 PIN code 17 TV overview 7 38 EN U USB disconnect USB 20 listen to music 19 update software 20 view photos 18 V video format technical specifications 3 volume adjust 10 automatic levelling 14 delta 14 mute 10 29 W wall mount 4 31 Information about how to re tune your TV during the TV switchover Keep this user manual safe you ll need it m n Television in the UK is going digital bringing us all more choice and new services Starting in late 2007 and ending in 2012 television services in the UK will go completely digital TV region by TV region Please see the next page to find out when your area switches to digital Digital UK is the independent non profit organisation leading the process of digital TV switchover in the UK Digital UK provides im partial information on what people need to do to prepare for the move to digital and when they need to do it How the switchover affects your TV equipment Your new TV has a digital tuner built in which means it is ready to receive the Freeview signal by simply plugging it into your aerial socket check if you can get digital TV through your aerial now or whether you ll hav
13. BACK to exit Reset the TV to factory settings You can restore the default picture and sound ings of your TV The channel installation ings remain the same Press MENU Select Setup gt Installation gt Factory settings Press gt to enter Factory settings Select Reset to start resetting Press OK Press t MENU to exit OuRW Nagg EN 21 English 6 Install channels The first time you set up your TV you are prompted to select a menu language and to install TV and digital radio channels if available This chapter provides instructions on how to re install and fine tune channels Automatically install channels This section describes how to search and store channels automatically Step 1 Select your menu language Note Skip this step if your language settings are correct U ress ft MENU Press AY 4b to select Setup gt Installation gt Menu language a U ress gt to enter Menu language ress AY to select a language Press OK to confirm ress MENU to exit U ON Ui Bb Ww N U b Select Start then press OK to re install channels e To stop searching select Stop and press OK 6 Press amp MENU to exit Manually install channels This section describes how to search and store analogue TV channels manually Step 1 Select your system Note Skip this step if your system settings are correct
14. RIESGO DE CHOQUE ELECTRICO e Any operation expressly prohibited in this manual or any adjustments and assembly procedures not recommended or authorised in this manual shall void the warranty Pixel characteristics This LCD product has a high number of colour pixels Although it has effective pixels of 99 999 or more black dots or bright points of light red green or blue may appear constantly on the screen This is a structural property of the display within common industry standards and is not a malfunction Compliance with EMF Koninklijke Philips Electronics N V manufactures and sells many products targeted at consumers which like any electronic apparatus in general have the ability to emit and receive electromagnetic signals One of Philips leading Business Principles is to take all necessary health and safety measures for our products to comply with all applicable legal requirements and to stay well within the EMF standards applicable at the time of producing the products Philips is committed to develop produce and market products that cause no adverse health effects Philips confirms that if its products are handled properly for their intended use they are safe to use according to scientific evidence available today Philips plays an active role in the development of international EMF and safety standards enabling Philips to anticipate further developments in standardisation for early integration in its produ
15. and causing injury to children ever place the TV on a surface covered by a cloth or other material that can be pulled away e Ensure that no part of the TV hangs over he edge of the surface ever place the TV on tall furniture such as a bookcase without anchoring both he furniture and TV to the wall or a suitable support e Educate children about the dangers of climbing on furniture to reach the TV Risk of overheating ever install the TV in a confined space Always leave a space of at least 4 inches or 10 cm around the TV for ventilation Ensure curtains or other objects never cover the ventilation slots on the TV Risk of damage to the TV Before you connect the TV to the power outlet ensure that the power voltage matches the value printed on the back of the TV Never connect the TV to the power outlet if the voltage is different Risk of injury fire or power cord damage ever place the TV or any objects on the power cord e To disconnect the TV power cord easily from the power outlet ensure that you have full access to the power cord at all imes When you disconnect the power cord always pull the plug never the cable Disconnect the TV from the power outlet and antenna before lightning storms During lightning storms never ouch any part of the TV power cord or antenna cable Risk of hearing damage Avoid using earphones or headphones at high volumes or for prolonged pe
16. channel grid appears 2 Press AV to select and preview a channel 3 Press OK to watch the selected channel EN 9 English Watch connected devices Note Switch on the device before selecting it as a source on the TV Use the source button MENU FORMAT INCR SURR MHEG 27 37 1 mmej pouc DEMO SUBTRE AS mmm as amp as 1 Press D SOURCE L gt The source list appears Press AY to select a device LJ N Press OK to confirm your choice L gt The TV switches to the selected device Adjust TV volume To increase or decrease volume e Press 4 To mute or unmute sound e Press X to mute the sound e Press K again to restore the sound 10 EN Use teletext MENU FORMAT INCR SURRY MHEG T rod Goure DEMO s st e AD sw umm 1 Press MHEG TELETEXT The main index page appears 2 Selecta page as follows Press the Numeric buttons to enter page number e Press P to view the next or previous page e Press the Colour buttons to select a colour coded item ress 9 BACK to return to a previously viewed page 3 Press MHEG TELETEXT to exit teletext w e U 5 Use more of your TV Access TV menus Menus help you to install channels change picture and sound settings and access other features 1 Press
17. mounting the TV use only the supplied stand Secure the stand to the TV tightly Place the TV on a flat level surface that can support the combined weight of the TV and the stand e When wall mounting the TV use only a wall mount that can support the weight of the TV Secure the wall mount to a wall that can support the combined weight of the TV and wall mount Koninklijke Philips vases near the TV If liquid or into the TV disconnect he power outlet immedia Philips Consumer Care to s are spilt on the TV from ely Contact have the TV Electronics N V bears no responsibility for improper wall mounting that result in accident injury or damage checked before use ever place the TV remote control or batteries near naked flames or other heat sources including direct sunlight To prevent the spread of fire keep candles or other flames away from the TV remote control and batteries at all times Never insert objects into the ventilation slots or other openings on the TV When the TV is swivelled ensure that no strain is exerted on the power cord Strain on the power cord can loosen connections and cause arcing Risk of short circuit or fire Never expose the remote control or batteries to rain water or excessive heat Avoid force coming onto power plugs Loose power plugs can cause arcing or fire EN Risk of injury to children Follow these precautions to prevent the TV from toppling over
18. 3 type Power Mains power 220 240V 50Hz Standby power lt 1 W e Ambient temperature 5 to 40 degrees Celsius Supported TV mounts To mount the TV purchase a Philips TV mount or a VESA compatible TV mount To prevent damage to cables and connectors be sure to leave a clearance of at least 2 2 inches or 5 5cm from the back of the TV Warning Follow all instructions provided with the TV mount Koninklijke Philips Electronics N V bears no responsibility for improper TV mounting that results in accident injury or damage TV screen Required Required mounting size pitch mm bolts inches 32 200 x 200 4x M6 lt 10 mm 42 300 x 200 4xM 6 lt 10 mm EN 31 English Product specification Design and specifications are subject to change without notice 32PFL3605 e Without TV stand Dimension WxHxD 795 6 x 508 3 x 93 mm Weight 8 3 kg e With TV stand Dimension WxHxD 795 6 x 556 6 x 220 8 mm e Weight 94 kg 42PFL3605 e Without TV stand Dimension WxHxD 1018 5 x 635 7 x 83 mm e Weight 11 5 kg e With TV stand Dimension WxHxD 1018 5 x 683 x 235 8 mm e Weight 12 8 kg 32 EN 9 Troubleshooting This section describes commonly encountered issues and accompanying solutions General TV issues The TV does not switch on e Disconnect the power cable from the power outlet Wait for one minute then reconnect it e Check that
19. General No 0800 331 6015 General National Rate No 0870 911 0036 0 800 500 697 Schweizer Festnetztarif Tarif r seau fixe France ehiri i arama free National rate This information is correct at the time of press For updated information see www philips com support Contents 1 Notice 2 2 Important 4 3 Your TV 7 Side controls and indicators 7 Remote contro 7 4 Use your TV 9 Switch your TV on off or to standby 9 Switch channels 9 Watch connected devices 0 Adjust TV volume 0 Use teletext 0 5 Use more of your TV 1 Access TV menus 1 Rename devices from the home menu 1 Remove devices from the home menu 1 Change picture and sound settings 2 Use advanced teletext features 4 Create and use list of favourite channels 15 Use the TV clock 6 Use timers 6 Use TV locks 7 View photos and play music from a USB storage device 8 Update the TV software 20 Change TV preferences 20 Access decoder channel 21 Start a I V demo 21 Reset the TV to factory settings 21 6 Install channels 22 Automatically install channels 22 Manually install channels 22 Rename channels 24 Rearrange channels 24 EN 7 Connect devices 25 Back connector 25 Side connector 27 Connect a computer 28 Use Philips EasyLink 29 Use a Kensington lock 30 Product information 31 Supported display resolutions 31 Multimedia 31 Tuner Reception Transmission 31 Remote control 31 Power 31 Supported TV mounts 31 Pr
20. Register your product and get support at www philips com welcome 32PFL3605 12 42PFL3605 12 EN User Manual PHILIPS Model Serial wwwphilips com support a Osterreich 0800 180 016 Belgi Belgique 80080190 Bparapua 00800 11 544 24 Hrvatska 01 6403 776 Lokalni poziv Cesk republika 800142840 Bezplatny hovor Danmark 3525 8759 Lokalt opkald Estonia 6008600 kohalik kone tariifi Suomi 09 2311 3415 paikallispuhelu France 0805 025 510 num ro sans frais Deutschland 0800 000 7520 geb hrenfreier Anruf E Aa a 0 0800 3122 1280 KArjon xwpis xp won Magyarorsz g 0680018189 Ingyenes h v s Hrvatska 0800 222778 free Ireland 01 601 1777 Italia 800 088774 Numero Verde KasakcraH 7 727 250 66 17 local Latvia 52737691 local Lithuania 67228896 local Luxemburg Luxembourg Nederland 40 6661 5644 0800 0230076 Ortsgesprach Appel local Gratis nummer Norge 22 70 81 11 Lokalsamtale Polska 00800 311 13 18 Pozosta e produkty RTV oraz AGD Portugal 800 780 903 Chamada Gr tis Rom nia 0800 894910 Apel gratuit 0318107125 Apel local Poccua 495 961 1111 0 15 USD minute Cp6uja 381 114 440 841 Lokalni poziv Slovensko 0800 004537 Bezplatny hovor Slovenija 00386 12 80 95 00 lokalni klic Espana 900 800 655 Tel fono local gratuito solamente para clientes en Espana Sverige 08 5792 9100 Lokalsamtal Suisse Schweiz Svizzera Turkiye United Kingdom Ykpa na 0800 002 050 0800 261 3302
21. andard Adjusts sound settings to suit most environments and types of audio e News Applies settings for spoken audio such as news e Movie Applies settings for movies e Custom Applies the settings that were customised in the sound menu Press OK to confirm your choice L gt The selected smart sound setting is applied e Auto volume Automatically reduces sudden volume changes for example when switching channels Delta volume Levels out volume differences between channels or connected devices Switch to the connected device before you change the delta volume Use advanced teletext features Access the teletext options menu Access the teletext features through the teletext options menu 1 Press MHEG TELETEXT L gt The teletext screen appears Manually adjust sound settings 1 2 3 Press amp MENU Press AV to selec The Sound men Press AV to selec Setup gt Sound u appears the following settings Smart sound Accesses pre defined smart sound settings Bass Adjusts the bass level e Treble Adjusts the treble level e Volume Adjusts the volume e Balance Adjusts the balance of the right and left speakers e Dual I II Selects audio languages if dual sound broadcast is available e Mono Stereo Selects mono or stereo if stereo broadcast is available TV speakers Turns TV speakers on or off Setting TV speakers to aut
22. cts Mains fuse UK only This TV is fitted with an approved moulded plug Should it become necessary to replace the mains fuse this must be replaced with a fuse of the same value as indicated on the plug example 10A 1 Remove fuse cover and fuse 2 The replacement fuse must comply with BS 1362 and have the ASTA approval mark If the fuse is lost contact your dealer in order to verify the correct type J Refit the fuse cover In order to maintain conformity to the EMC directive the mains plug on this product must not be detached from the mains cord cable Copyright Kensington and Micro Saver are registered US trademarks of ACCO World corporation with issued registrations and pending applications in other countries throughout the world Home HDMI the HDMI logo and High Definition ultimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC All other registered and unregistered trademarks are the property of their respective owners EN English 2 Important Read and understand all instructions before you use your TV If damage is caused by failure to follow instructions the warranty does not apply Safety Risk of electric shock or fire ever expose the TV to rain or water ever place liquid containers such as Risk of injury or damage to the TV Two people are required to lift and carry a TV that weighs more than 25 kg e When stand
23. duct helps to prevent potential negative consequences for the environment and human health A Your product contains batteries covered by the European Directive 2006 66 EC which cannot be disposed with normal household waste Please inform yourself about the local rules on separate collection of batteries because correct disposal helps to prevent negative consequences for the environmental and human health EN 5 English Energy efficiency features e Ambient light sensor Available in selected models only To save energy the built in Ambient light sensor lowers the brightness of the TV screen when the surrounding light darkens e Energy saving The energy saving setting of the TV combines several TV settings that result in saving energy See the smart settings in the setup menu Low standby power consumption The class leading and highly advanced power circuitry brings down the power consumption of the TV to an extremely low level without losing out on the constant standby functionality Power management Available in selected models only The advanced power management of this TV ensures the most efficient use of its energy You can check how your personal TV settings the level of brightness in current onscreen pictures and the surrounding light conditions determine the relative power consumption End of use To inform yourself on the correct disposal of the TV and batteries refer to Disposal of your old pr
24. e new channel Press amp MENU to exit Step 3 Fine tune analogue channels 1 2 Oo ON AUB W Press amp MENU Press to select Setup gt Installation gt Channel installation Analogue Manual The Analogue Manual menu appears Press AY to select Fine tune then press gt to enter Press AY to adjust frequency Press OK to confirm Press AY to select Store current hannel to store channel number o P ress gt to enter Store current channel Select OK then press OK to store current channel Press amp MENU to exit Skip channels 1 2 When watching TV switch to the channel you want to skip Press amp MENU Press AY 4b to select Setup gt Installation gt Channel installation gt Analogue Manual L gt The Analogue Manual menu appears Press AY to select Skip channel then press gt to enter Press AY to select Yes then press OK to skip current channel L gt The selected channel is skipped when you press P on your remote control or view from the channel grid Repeat the previous steps to skip more channels Tip Press the Numeric buttons on the remote control to access the skipped channel To access the skipped channel repeat steps 1 5 and select No to restore EN 23 English Rename channels You can rename channels The name appears when you select the channel 1 2 3
25. e TOP overview appears Press AY 4b to select a subject 3 4 Press OK to view the page Create and use list of favourite channels You can create a list of your preferred TV channels so that you can find those channels easily Select a favourite list 1 when watching TV press OK to display the channel grid 2 Press OPTIONS L gt The channel options menu appears J Press Av to select Select list then press OK to enter The channel list options appear 4 Select Favourite then press OK Only channels in the favourite list appear in the channel grid Note The favourite channel grid is empty until you add channels into the favourite lists View all channels You can exit a favourite list and view all installed channels 1 when watching TV press OK L gt The channel grid appears 2 Press OPTIONS L gt The channel options menu appears J Press Av to select Select list then press OK or to enter 4 Select All then press OK All channels are displayed in the channel grid Note All favourite channels are marked by an asterisk when you view the channel grid EN 15 English Add a channel to a favourite list 1 when watching TV press OK L gt The channel grid appears 2 Press AY 4b to select a channel to add to a favourite list 3 Press OPTIONS L gt The channel options menu appears 4 Select Mark as favourite then
26. e to wait until switchover at www digitaluk co uk When the TV switchover happens in your area there are at least two occasions when you will need to re tune your TV in order to continue receiving your existing TV channels and also to pick up new ones get set for digital V EN 39 Digital UK the body leading the digital TV switchover will advise you when you need to re tune during the switchover If you choose to connect your TV to satellite or cable with a digital box then it will not be affected by switchover and you won t need to re tune If you have any questions please contact your equipment supplier or call Digital UK on 0845 6 50 50 50 or visit www digitaluk co uk How to re tune To find out on how to re tune your TV check the user manual online for details If you do not re tune your channels when advised to do so by Digital UK you may lose some or all of your channels until you do re tune You should re tune your TV every few months to check for any new channels If you are missing any channels it may be that they are not available in your area or that your aerial needs upgrading When does switchover happen Copeland switches on October 17 2007 Visit us at digitaluk co uk Call us on 0845 6 50 50 50t tCalls charged at BT rate of 3p per minute daytime and 1p per minute evenings and weekends Rates may vary for calls from non BT lines 40 EN H Border A 4 d gt 5
27. el grid when watching TV 9 av Navigation buttons avigates menus INFO Displays program information when available If the information spans multiple pages press OPTIONS to go to the next page GD s amp Mute utes or restores volume 2 P Programme Switches to the next or previous channel When the TV menu is on this functions as Page Up Down 3 0 9 Numeric buttons Selects a channel or setting C PICTURE Smart picture P Launches the picture menu 5 SOUND Smart Sound Launches the sound menu A l Volume Increases or decreases volume D BACK P P Previous channel e Returns to a previous screen e Returns to the previously viewed channel GUIDE Switches between channel grid and programme list SUBTITLE For RF Digital TV only Enables or disables subtitles DEMO Used in selected models only Toggles the demonstration menu on or off amp ED FORMAT Selects a picture format amp G tz INCR SURR Enables Incredible Surround for stereo sources Enables spatial mode for mono sources Remote control usage When using the remote control hold it close o the TV and point it at the remote control sensor Make sure that the line of sight between the remote control and TV is not blocked by furniture walls or other objects 4 Use your TV This section helps you perform basic TV operation
28. ere you are installing the TV see Step 2 Select your country on page 22 EN 33 English Picture issues The TV is on but there is no picture e Check that connected t e Check that he antenna is properly o the T V he correct device is selected as the TV source There is sound but no picture e Check that correctly set he picture settings are There is poor TV reception from an antenna connection e Check that connected t Loudspeake neon lights objects can f possible t he antenna is properly o the TV rs unearthed audio devices high buildings and other large influence reception quality ry to improve the reception quality by changing the antenna direction evices away from the TV on only one channel is poor s channel There is poor picture quality from connected or moving d e If reception fine tune thi devices Check that properly e Check that correctly set he devices are connected he picture settings are The TV did not save your picture settings e Check that home settin flexibility to he TV location is set to the g This mode offers you the change and save settings The picture does not fit the screen it is too big or too small e Try using a different picture format The picture position is incorrect Picture signals from some devices may not fit the screen correctly Check the signal outpu 34 EN t of the dev
29. gt The selected picture format is activated Press OK to confirm your choice Summary of picture formats The following picture settings can be configured Note Depending on the format of the picture source some picture settings are not available Auto format Not for Automatically displays the suitable picture format If not widescreen is applied HDMI YPbPr or PC mode Super zoom Not for HD and PC mode There is minimal distortion Removes the black bars on the side of 4 3 broadcasts format 4 3 Shows the classic 4 3 Subtitle zoom Displays 4 3 pictures over the full area of the screen with sub titles visible Part of the top ofthe picture is clipped off Movie expand 14 9 Not for HD and PC mode Scales 4 3 format to 14 9 Movie expand 16 9 Not for HD and PC mode Scales 4 3 format to 16 9 Wide screen Scales 4 3 format to 16 9 VOED I Unscaled Available in selected models with PC resolution under 1024 x 768 only Allows maximum sharpness Some distortion may be present due to the broadcaster s systems Set your PC resolution to wide screen mode for best results EN 13 English Use smart sound Use smart sound to apply pre defined sound settings 2 3 Press SOUND L gt The Smart sound menu appears Press AY to select the following settings St
30. ice Sound issues There is a picture but sound quality is poor Note f no audio signal is detected the TV automatically switches the audio output off this does not indicate malfunction e Check that all cables are properly connected Check that the volume is not set to 0 Check that the sound is not muted There is a picture but the sound quality is poor e Check that the sound settings are correctly set There is a picture but sound comes from one speaker only e Verify that sound balance is set to the centre HDMI connection issues There are problems with HDMI devices e Note that HDCP High bandwidth Digital Content Protection support can delay the time taken for a TV to display content from a HDMI device e Ifthe TV does not recognise the HDMI device and no picture is displayed try switching the source from one device to another and back again fthere are intermittent sound disruptions check that output settings from the HDMI device are correct e Ifyou use an HDMI to DVI adapter or HDMI to DVI cable check that an additional audio cable is connected to AUDIO IN mini jack only Computer connection issues The computer display on the TV is not stable Check that your PC uses the supported resolution and refresh rate Set the TV picture format to unscaled Contact us f you cannot resolve your problem refer to the FAQs for this TV at www
31. in the slide show J Press OK to confirm your setting Note Rotate image and Show info appear only when you press OK to pause the slideshow Listen to music 1 In USB browser view select MUSIC and press to enter 2 Press AV to select a music track or album J Press OK to play the selected music Button Function OK Pause resume play or stop playback lt gt Go to the previous or next music Music settings When listening to music press OPTIONS to access one ofthe following music settings Start playback Stop playback Starts or stops the music e Play mode e Play once Disables repeat play and plays a song once e Repeat Repeats a song e Shuffle Plays songs randomly e Show info Displays the file name e Sound Adjusts the sound setting e TV speakers Sets the TV speakers on or off Only available if EasyLink is switched on View a slideshow with music You can view a picture slide show with background music 1 Select an album of songs Press OK Press gt BACK to return to the USB content browser Ww N Select an album of pictures Press OK UA Disconnect a USB storage device Caution Follow this procedure to avoid damage to your USB storage device 1 Press BACK to exit the USB browser 2 Wait for five seconds then disconnect the USB storage device EN 19 English Update the TV software
32. o view photos or listen to music stored on a USB storage device 1 Turn on the T V 2 Connect the USB s orage device to the TV The home menu appears Press AY 4b to select Browse USB a LW Press OK to confirm L gt The USB thumbnail browser appears Tip Press GUIDE to switch between thumbnail and file browsing views View photos 1 In the USB browser press P to enter the Picture folder 2 Press AV to select a photo or a photo album J Press OK to view a full screen image of the photo Tip e When in full screen mode press to move between photos View a slide show of your photos 1 When a full screen image of a photo is displayed press OK L gt A slide show begins from the selected photo 2 Press the following buttons to control the slide show OK to pause the slide show e 4k to go back or move forward to the next image BACK to stop the slide show Change slide show settings 1 when viewing a slide show press OPTIONS L gt The slide show options menu appears 2 Press AV to select one of the following e Start Slideshow Stop Slideshow Starts or stops a slide show Slideshow transitions Sets the transition from one picture to the next Slideshow frequency Sets the amount of time that a picture is shown Rotate image Rotates a picture e Show info Displays the picture name date size and next picture
33. oduct and batteries in the user manual see Disposal of your old product and batteries on page 5 3 Your TM Remote control Congratulations on your purchase and welcome to Philips To fully benefit from the support that Philips offers register your TV at www philips com welcome This section gives you an overview of commonly used TV controls and functions Side controls and indicators al aro EO NETS ACC fj eo Rmmuazuak n lt Increases or decreases volume PHILIPS TELEVISION Q ft Home Toggles the home menu on or off 9 P CH Switches to the next or previous channel o Power Switches the product on or off The product is not powered off completely unless it is physically unplugged G Standby indicator and remote control sensor EN English 4 Standby On e Switches the TV to standby if it is on e Switches on the TV if it is in standby 2 MENU Toggles the main menu on or off GB MHEG TELETEXT Toggles teletext on or off amp SOURCE Selects connected devices Colour buttons Selects tasks or options AD Audio Descriptor For RF Digital TV only UK only Enables audio commentary for the visually handicapped OPTIONS Accesses options relating to the current activity or selection 8 OK Confirms an entry or selection and displays the chann
34. oduct specification 32 Troubleshooting 33 General TV issues 33 TV channel issues 33 Picture issues 34 Sound issues 34 HDMI connection issues 34 Computer connection issues 35 Contact us 35 10 Index 36 English 1 Notice 2010 Koninklijke Philips Electronics N V All rights reserved Specifications are subject to change without notice Trademarks are the property of Koninklijke Philips Electronics N V or their respective owners Philips reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly The material in this manual is believed adequate for the intended use of the system If the product or its individual modules or procedures are used for purposes other than those specified herein confirmation of their validity and suitability must be obtained Philips warrants that the material itself does not infringe any United States patents No further warranty is expressed or implied Warranty e Risk of injury damage to TV or void of warranty Never attempt to repair the TV yourself e Use the TV and accessories only as intended by the manufacturer e The caution sign printed on the back of the TV indicates risk of electric shock Never remove the TV cover Always contact Philips Customer Support for service or repairs CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR PRECAUCION ADVERTENCIA NO ABRIR
35. omatic mode turns off the speakers when content from an EasyLink compliant home theatre system is detected Only available if EasyLink is switched on Surround Enables spatial sound EN 2 Press OPTIONS L gt The teletext opt ptions Freeze page ions menu appears Press AY to select one of the following o Freezes the current page Dual Full screen Enables and disables dual screen teletext Reveal Hides or reveals hidden information on a page such as solutions to riddles or puzzles Cycle subpage Cycl subpages automatical are available Language Switches language group to dis es through y if subpages to a different play a language correctly when it uses a different character set Press AV to make ase press OK to confirm Press gt BACK to exit the teletext options menu ection then Select teletext subpages A teletext page can hold several subpages Subpages are displayed on a bar next to the main page number Press MHEG TELETEXT L gt The teletext screen appears 2 Press P to select a teletext page J Press lt P to enter a subpage Select T O P teletext broadcasts Table Of Pages T O P teletext broadcasts allow you to jump from one subject to another without using page numbers T O P teletext is not broadcast on all T V channels 1 Press MHEG TELETEXT L gt The teletext screen appears 2 Press INFO L gt Th
36. philips com support fthe problem remains unresolved contact Philips Consumer Care in your country as isted in this user manual VN Warning Do not attempt to repair the TV yourself This may cause severe injury irreparable damage to your TV or void your warranty Make a note of your TV model and serial number before you contact Philips These numbers are printed on the back of the TV and on the packaging EN 35 English 10 Index A analogue fine tune 23 antenna 25 B back connectors 25 batteries 31 5 bracket for wall mount 31 C care 5 channel decoder 21 channel grid 9 channels favourites list 15 fine tune 23 grid 9 install automatic 22 manual 22 ist 15 ock 17 rename 24 reorder rearrange 24 skip channels 23 switch 9 roubleshooting 33 une 23 child lock ock channels 18 ock connected devices 17 PIN code 17 clock set 16 computer connect 35 28 display resolution 31 connect antenna 25 PC 35 28 36 EN connectors back connectors 25 HDMI 34 25 overview 25 side connectors 27 USB 18 country 22 D decoder 2 default settings 2 demo 2 devices 0 devices add to home menu connect 25 remove rename watch 0 digital services teletext 10 14 disconnect USB 20 display resolution 3 dispose 5 E EasyLink disable 29 enable 29 one touch play 29 one touch standby 29 system audio control 29 end of life 5 environmental care 5 e s
37. press OK The channel is added to the favourite list Note All favourite channels are marked by an asterisk in the channel grid Remove a channel from a favourite list 1 when watching TV press OK L gt The channel grid appears Press AY4b to select a channel to remove Press OPTIONS Select Unmark as fav then press OK Select Yes then press OK L gt The channel is removed Ui w Use the TV clock You can display a clock on the TV screen Set the TV clock 1 Pres amp MENU 2 select Setup gt Features gt Clock The Clock menu appears 3 Press Av or Numeric buttons to enter time Select Done and press OK to confirm Press f MENU to exit Ui A 16 EN Display the TV clock 1 When watching TV press amp OPTIONS L gt The TV option menu appears 2 Select Clock 3 Press OK Use timers You can set timers to switch the TV to standby at a specified time Tip Set the TV clock before you use timers Automatically switch the TV to standby sleep timer Sleep timer switches the TV to standby after a pre defined period of time Tip You can switch off your TV earlier or reset the sleep timer during the countdown 1 Press amp MENU 2 Press AYP to select Setup gt Features gt Sleep timer The Sleep timer menu appears 3 Press lt P to select a value between zero and 180 minutes
38. riods of time Low temperatures e Ifthe TV is transported in temperatures below 5 C unpack the TV and wait until the TV temperature matches room temperature before connecting the TV to the power outlet Screen care Avoid stationary images as much as possible Stationary images are images that remain on screen for extended periods of time Examples include on screen menus black bars and time displays If you must use stationary images reduce screen contrast and brightness to avoid screen damage Unplug the TV before cleaning e Clean the TV and frame with a soft damp cloth Never use substances such as alcohol chemicals or household cleaners on the TV e Risk of damage to the TV screen Never touch push rub or strike the screen with any object e o avoid deformations and colour fading wipe off water drops as soon as possible Disposal of your old product and batteries e Your product is designed and manufactured with high quality materials and components which can be recycled and reused A When this crossed out wheeled bin symbol is attached to a product it means that the product is covered by the European Directive 2002 96 EC Please inform yourself about the local separate collection system for electrical and electronic products Please act according to your local rules and do not dispose of your old products with your normal household waste Correct disposal of your old pro
39. rol and enable the TV speakers Note To mute the TV speakers select TV speakers gt Off EN 29 English Use a Kensington lock There is a Kensington security slot at the back of the TV Prevent theft by looping a Kensington ock between the slot and a permanent object such as a heavy table 30 EN 8 Product information Product information is subject to change without notice For detailed product information go to www philips com support Supported display resolutions Computer formats Resolution refresh rate 640 x 480 60Hz e 800 x 600 60Hz 024 x 768 60Hz 280 x 768 60Hz 280 x 1024 60 Hz 360 x 768 60Hz 440 x 900 60Hz 680 x 1050 60Hz Video formats Resolution refresh rate 480i 60Hz 480p 60Hz e 576i 50Hz 576p 50Hz e 720p 50Hz 60Hz e 1080i 50Hz 60Hz e 1080p 24Hz 25Hz 30Hz 50Hz 60Hz Multimedia Supported storage device USB Only FAT or FAT 32 USB storage devices are supported e Supported multimedia file formats Images JPEG e Audio MP3 Tuner Reception Transmission e Aerial input 75ohm coaxial IEC75 e TV system PAL I B G D K SECAM B G D K L L e Video playback NTSC SECAM PAL e Tuner Bands Hyperband S channel UHF VHF Remote control e ype PFO2EO9B e Batteries 2 x AAA LRO
40. s Switch your TV on off or to standby oe f EG dd LJ To switch on e Ifthe standby indicator is off press Power at the side of the TV e Ifthe standby indicator is red press Standby On on the remote control To switch to standby e Press Standby On on the remote control L gt The standby indicator switches to red To switch off e Press Power at the side of the TV L gt The standby indicator switches off El Though your TV consumes very little power when in standby energy continues to be consumed When not in use for an extended period of time disconnect the TV power cable from the power outlet e f you cannot locate your remote control and want to switch on the TV from standby press P CH on the side of the TV Switch channels e Press P on the remote control or P CH on the side of the T V e Enter a channel number using the Numeric buttons e Press OK to use the channel grid Press gt BACK P P on the remote control to return to the previous channel Note When you use a favourite list you can only select those channels in the list see Select a favourite list on page 15 Switch channels with the channel grid The channel grid allows you to view all available channels in a grid format tM e e e Y phere e x 1 Press OK L gt The
41. the power cable is securely connected The remote control is not working properly Check that the remote control batteries are correctly inserted according to the orientation e Replace the remote control batteries if hey are flat or weak Clean the remote control and TV sensor ens The standby light on the TV blinks red Disconnect the power cable from the power outlet Wait until the T V cools down before reconnecting the power cable If the blinking reoccurs contact Philips Consumer Care You forgot the code to unlock the TV lock feature Enter 8888 The TV menu is in the wrong language Change the T V menu to your preferred anguage When turning the TV on off to standby you hear a creaking sound from the TV chassis e No action is required The creaking sound is normal expansion and contraction of the TV asit cools down and warms up This does not impact performance Cannot remove e sticker banner displayed on theTV To remove the logos and images set the location of your TV to home 1 Press amp MENU 2 Select Setup gt Installation gt Preferences gt Location 3 Select Home and press OK TV channel issues Previously installed channels do not appear in the channel list Check that the correct channel list is selected Some channels are not automatically installed on my TV During installation make sure that you select the country wh
42. ticker 20 F factory settings 21 favourites list create list 15 view list 15 fine tune channels 23 H HDMI 34 25 27 home mode 20 install channels automatic 22 manual 22 K Kensington lock 30 L language menu 22 troubleshoot 33 list favourites list 15 location country 22 home or shop 20 lock Kensington lock 30 lock channels 18 lock connected devices 17 PIN code 17 M menu language 22 main menu 1 teletext 4 MHEG teletext 0 MPEG artifact reduction 2 multimedia 31 music USB 9 with slideshow 9 mute TV speakers 29 O on timer 16 one touch play 29 one touch standby 29 P PC connect 28 35 resolution 31 picture format change T3 troubleshooting 34 picture settings 12 PIN code 17 pixel plus link 20 power 31 power consumption 31 preferences 20 product specifications 31 R rearrange channels 24 reception 34 recycle 5 register product 7 remote control batteries 31 5 overview y technical specifications 31 rename channels 24 reorder channels 24 resolution 31 restore default 21 EN 37 English S safety 4 screen care 5 settings picture 12 sound 14 shop mode 20 side connectors 27 skip channels 23 slideshow view 9 with music 9 smart picture 2 smart settings 12 14 smart sound 4 software version 20 sound settings 4 specifications 3 standby 9 subpages in teletext 5 switch channels 9 on and off 9 source 10 T Table of Pages 5
43. ts the intensity of backlight areas keeping video contents unchanged e Brightness Adjusts the intensity and details of dark areas e Colour Adjusts colour saturation e Hue Compensates for colour variations e Sharpness Adjusts sharpness in the image e Noise reduction Filters and reduces noise in an image e Tint Adjusts the colour balance in an image e Custom tint Customises tint setting Only available if Tint gt Custom is selected e Dig Crystal Clear Fine tunes each pixel to match surrounding pixels This produces a brilliant high definition image e Dynamic contrast Enhances contrast You can switch this feature on or off e Dynamic backlight Adjusts brightness of the TV backlight to match lighting conditions e Colour enhancement Makes colours more vivid and improves the details in bright colours You can switch this feature on or off PC mode Adjusts the picture when a PC is connected to the TV via HDMI or DVI e Picture format Changes the picture format Picture size Adjusts the viewing area when set to maximum you might see noise or a rough edge of an image Horizontal shift Adjusts the picture horizontally for PC VGA input Vertical shift Adjusts the picture vertically for PC VGA input Change picture format 1 2 3 Press amp 3 FORMAT L gt A picture format bar appears Press AY to select a picture format L
44. ur TV and the devices with one remote control One touch standby When you connect your TV to devices that support standby you can use your TV remote control to put your TV and all connected HDMI devices in standby mode System audio control When you connect your TV to HDMI CEC compliant devices your TV can switch automatically to play audio from the connected device To use one touch audio you must map the audio input from the connected device to your T V You can use the remote control from the connected device to adjust the volume Enable or disable EasyLink Note Do not enable Philips EasyLink if you do not intend to use it Press amp MENU 1 2 Press AY to select Setup gt Installation gt Preferences gt EasyLink J Select On or Off Set TV speakers to EasyLink mode When you play content from an EasyLink compliant home theater the TV speakers are automatically muted 1 Enable one touch play and one touch standby between your Easylink compliant devices by following the instructions in the previous section see Enable or disable EasyLink on page 29 Press MENU Press AV to select Setup gt Sound gt TV speakers gt Auto EasyLink L gt The TV speakers are turned off automatically when content from an Easylink compliant system is detected Ww N 4 Press Av to select Setup gt Sound gt TV speakers gt On to disable system audio cont
Download Pdf Manuals
Related Search