Home

Samsung LE-26C450E1WXZG 26" Full HD Black LCD TV

1. Problem Possible Solution Anynet does not work e Check if the device is an Anynet device The Anynet system supports Anynet devices only e Connect only one receiver home theatre e Check if the Anynet device power cord is properly connected e Check the Anynet device s Video Audio HDMI Cable connections e Check whether Anynet HDMI CEC is set to On in the Anynet setup menu e Check whether the TV remote control is in TV mode e Check whether it is Anynet exclusive remote control e Anynet does not work in certain situations Searching channels operating Media Play or Plug amp Play Initial setup etc e When connecting or removing the HDMI cable please make sure to search devices again or turn your TV off and on again e Check if the Anynet Function of Anynet device is set on want to start Anynet e Check if the Anynet device is properly connected to the TV and check if the Anynet HDMI CEC is set to On in the Anynet Setup menu e Press the TOOLS button to display the Anynet menu and select a menu you want want to exit Anynet e Select View TV in the Anynet menu e Press the SOURCE button on the TV remote control and select a device other than Anynet devices e Press P A PRE CH and FAV CH to change the TV mode Note that the channel button operates only when a tuner embedded Anynet device is not connected The message Connecting to e You cannot
2. TV Side Panel E By Channel Upgrade the software using the HD Connection Guide 2 broadcasting signal Q Ifthetunction is selected during the software Refer to this information when connecting external devices w jet transmission period software will be automatically to the Tv A searched and downloaded n The time required to download the software is Contact Samsung S i j determined by the signal status View this information when your TV does not work properly oO E Standby Mode Upgrade A manual upgrade will be or when you want to upgrade the software You can find te automatically performed at selected time Since the information regarding our call centres and how to download power of the unit is turned on internally the screen products and software may be turned on slightly for the LCD product This phenomenon may continue for more than 1 hour until the software upgrade is complete E Alternative Software backup If there is an issue with the new firmware and it is affecting operation you can change the software to the previous version amp Q If the software was changed existing software is displayed English 2 1 Advanced Features Using an HDMI DVI Cable a D sub Cable oto PC DVI AUDIO IN Display Modes D Sub and HDMI DVI Input Optimal resolution is 1360 X 768 60 Hz
3. Issues Picture Quality Solutions and Explanations First of all please perform the Picture Test and confirm that your TV is properly displaying test image go to MENU Support Self Diagnosis Picture Test P 20 If the test image is properly displayed the poor picture may caused by the source or signal The TV image does not look as good as it did in the store UOIPEULIOJU JOUIO GO e If you have an analogue cable set top box upgrade to a digital set top box Use HDMI or Component cables to deliver HD high definition picture quality e Cable Satellite subscribers Try HD stations from the channel line up e Antenna connection Try HD stations after performing Auto programme amp Many HD channels are upscaled from SD Standard Definition contents e Adjust the Cable Set top box video output resolution to 1080i or 720p e Make sure you are watching the TV at the minimum recommended distance based on the size and definition of the signal The picture is distorted macroblock error small block dots pixelization e Compression of video contents may cause picture distortion especially in fast moving pictures such as sports and action movies e Low signal level or bad quality can cause picture distortion This is not a TV issue Colour is wrong or missing e If you are using a component connection make sure the component cables are connected to the correct jacks Incorrect or loose connections may cause colo
4. Colour buttons red green yellow blue If the FASTEXT system is used by a broadcasting company the different topics covered on a Teletext page are colour coded and can be selected by pressing the coloured buttons Press one of them corresponding to the required The page is displayed with other coloured information that can be selected in the same way To display the previous or next page press the corresponding coloured button Part Contents Part Contents A Selected page number D Date and time B Broadcasting channel identity E Text c Current page number or F Status information FASTEXT search indications information 3 2 English Installing the Wall Mount iil Installing the Wall Mount Kit Wall mount items sold separately allow you to mount the TV on the wall For detailed information on installing the wall mount see the instructions provided with the Wall Mount items Contact a technician for assistance when installing the wall mount bracket Samsung Electronics is not responsible for any damage to the product or injury to yourself or others if you elect to install the TV on your own fl Wall Mount Kit Specifications VESA amp Wall mount kit is not supplied but sold separately Install your wall mount on a solid wall perpendicular to the floor When attaching to other building materials please contact your nearest dealer If installed on a ceiling or
5. AD Audio Description selection Not available in some locations P 17 P SIZE Choose the picture size P 15 SUBT Digital subtitle display P 19 Installing batteries Battery size AAA a LO Displays and selects the available video sources P 9 peyeys Buap Returns to the previous channel Cuts off the sound temporarily Changes channels Displays channel list on the screen P 13 Display the EPG Electronic Programme Guide P 10 Displays information on the TV screen P 10 Selects on screen menu items and change menu values Exit the menu Use these buttons in the Media Play and Anynet modes P 23 29 lt gt gt Controls recording on Samsung recorders with the Anynet feature e Use the remote control within 23 feet from the TV e Bright light may affect the performance of the remote control Avoid using nearby special fluorescent light or neon The colour and shape may vary depending on the model English 5 Getting Started When the TV is initially powered on basic settings proceed automatically Q Preset Connecting the mains and antenna VHF UHF Antenna Cable Power Input Plug amp Play Initial Setup When the TV is initially powered on a sequence of on screen prompts will assist in configuring basic settings Press the POWER button Plug amp Play is
6. Mode Resolution Pee o clic ls Pixel rv S ner 640 x 350 31 469 70 086 25 175 IEM 720 x 400 31 469 70 087 28 322 MAG 640 x 480 35 000 66 667 30 240 832 x 624 49 726 74 551 57 284 31 469 59 940 25 175 640 x 480 37 861 72 809 31 500 37 500 75 000 31 500 37 879 60 317 40 000 800 x 600 48 077 72 188 50 000 VESA DMT 46 875 75 000 49 500 48 363 60 004 65 000 1024 x 768 56 476 70 069 75 000 60 023 75 029 78 750 1280 x 720 45 000 60 000 74 250 1360 x 768 47 712 60 015 85 500 VESA CVT 720 x 576 35 910 59 950 32 750 1280 x 720 56 456 74 777 95 750 VESA GTF 1280 x 720 52 500 70 000 89 040 amp NOTE e For HDMI DVI cable connection you must use the HDMI DVI IN 1 jack e The interlace mode is not supported The set might operate abnormally if a non standard video format is selected Separate and Composite modes are supported SOG Sync On Green is not supported 2 2 English Media Play Enjoy photos music and or movie files saved on a MediaPlay MEDIA P USB Mass Storage Class MSC device WE sum A Change Device ices C8 Enter D Return D Connecting a USB Device 1 Turnon your TV TV Side Panel 2 Connect a USB device containing photo music and or movie files to the USB HDD jack on the side of the TV 3 When USB is connected to the TV popup window appears Then you can select Media Play USB Drive Wit might not work properly wi
7. sounjyes j dIseg 0 Basic Features i Picture In Picture PIP PIP Watches simultaneously the TV tuner and one external video source PIP Picture in Picture does not function in the same mode NOTE e Ifyou turn the TV off while watching in PIP mode the PIP window will disappear You may notice that the picture in the PIP window becomes slightly unnatural when you use the main screen to view a game or karaoke e PIP settings Main picture Sub picture Component HDMI1 DVI Tv HDMI2 HDMI3 PC E PIP Off On Activate or deactivate the PIP function Size iml _ Select a size for the sub picture E Position J L3 EJ b sub picture Select a position for the H Channel Select the channel for the sub screen E Sound Select Main Sub You can choose the desired sound Main Sub in PIP mode Support Menu Self Diagnosis Self Diagnostic might take few seconds this is part of the normal operation of the TV H Picture Test Yes No Use to check for picture problems and if the problem continues to occur check the colour pattern E Sound Test Yes No Use the built in melody sound to check for sound problems Q if you hear no sound from the TV s speakers before performing the sound test make sure Speaker Select is set to TV speaker in the Sound menu The melody will be heard during the test even if Speaker Se
8. system can be used only with Samsung devices that have the Anynet feature To be sure your Samsung a device has this feature check if there is an Anynet logo on it lot To connect to Home Theatre g E D Aaaa ke aeeie k oa Home Theatre Anynet Device 1 Anynet Device 2 3 a 0 CS CS DIGITAL AUDIO N HDMI IN b FERH Sir _ Optical Cable HDMI Cable 2 Tu r eaaineanbanteauunaetesannaunuacenaestacuvansuaatnanrses i HDMI Cable 1 Connect the HDMI DVI IN 1 2 or 3 jack on the TV and the HDMI OUT jack of the corresponding Anynet device using an HDMI cable 2 Connect the HDMI IN jack of the home theatre and the HDMI OUT jack of the corresponding Anynet device using an HDMI cable amp NOTE Connect the Optical cable between the DIGITAL AUDIO OUT OPTICAL jack on your TV and the Digital Audio Input on the Home Theatre e When following the connection above the Optical jack only outputs 2 channel audio You will only hear sound from the Home Theatre s Front Left and Right speakers and the subwoofer If you want to hear 5 1 channel audio connect the DIGITAL AUDIO OUT OPTICAL jack on the DVD satellite box i e Anynet Device 1 or 2 directly to the Amplifier or Home Theatre not the TV Connect only one Home Theatre e You can connect an Anynet device using the HDMI cable Some HDMI cables may not support Anynet func
9. TV from an antenna or cable connection the TV will turn off after 10 15 minutes if there is no signal There is picture Video Check cable connections remove and reconnect all cables connected to the TV and external devices Set your external devices Cable Set top Box DVD Blu ray etc video outputs to match the connections to the TV input For example if an external device s output is HDMI it should be connect to an HDMI input on the TV Make sure your connected devices are powered on Be sure to select the TV s correct source by pressing the SOURCE button on the TV remote RF Cable Antenna Connection The TV is not receiving all channels Make sure the Antenna cable is connected securely Please try Plug amp Play Initial setup to add available channels to the channel list Go to MENU Setup Plug amp Play Initial setup and wait for all available channels to be stored Verify the Antenna is positioned correctly The picture is distorted macroblock error small block dots pixelization Compression of video contents may cause picture distortion especially with fast moving pictures such as sports and action movies A low signal can cause picture distortion This is not a TV issue PC Connection A Not Supported Mode message e Set your PC s output resolution and frequency so they match the resolutions supported by the TV P appears 22 PC is always shown on
10. concerning operation and maintenance has ING TO QUALIFIED PERSONNEL been included with this product The slots and openings in the cabinet and in the back or bottom are provided for necessary ventilation To ensure reliable operation of this apparatus and to protect it from overheating these slots and openings must never be blocked or covered Do not cover the slots and openings with a cloth or other materials Do not block the slots and openings by placing this apparatus on a bed sofa rug or other similar surface Do not place this apparatus in a confined space such as a bookcase or built in cabinet unless proper ventilation is provided Give your product 10 cm 4 inch clearance from the wall Do not place this apparatus near or over a radiator or heat resistor or where it is exposed to direct sunlight Do not place heat generating items such as candles ashtrays incense flammable gas or explosive materials near the product Do not place a water containing vessel on this apparatus as this can result in a risk of fire or electric shock Do not expose this apparatus to rain or place it near water near a bathtub washbowl kitchen sink or laundry tub in a wet basement or near a swimming pool etc If this apparatus accidentally gets wet unplug it and contact an authorized dealer immediately Make sure to pull out the power cord from the outlet before cleaning e This apparatus use batteries In your communi
11. modulation values Symbol Rate Displays available symbol rates 1 2 English Manual Store Scans for a channel manually and stores in the TV If a channel is locked using the Child Lock function the PIN input window appears H Digital Channel available in DTV mode When scanning has finished channels are updated in the channel list amp When selecting Antenna Air Channel Frequency Bandwidth amp When selecting Antenna Cable Frequency Modulation Symbol Rate H Analogue Channel Programme Colour System Sound System Channel Search If there is abnormal sound or no sound reselect the sound standard required amp Channel mode P programme mode When tuning is complete the broadcasting stations in your area have been assigned to position numbers from PO to P99 You can select a channel by entering the position number in this mode C aerial channel mode S cable channel mode These two modes allow you to select a channel by entering the assigned number for each aerial broadcasting station or cable channel a Editing channels Channel Manager Option Menu in Channel Manager 1 Select a channel and press the TOOLS button 2 Edit the channel name or number using the Edit Channel Name or Edit Channel Number menu E Edit Channel Name analogue channels only Assign your own channel name E Edit Channel Number digital channels only Edit the number by pressing the number buttons de
12. provides an improved sound experience compared to Normal mode making almost no noise It is useful at night Speaker Select External speaker TV speaker A sound echo may occur due to a difference in decoding speed between the main speaker and the audio receiver In this case set the TV to External Speaker amp When Speaker Select is set to External Speaker the volume and MUTE buttons will not operate and the sound settings will be limited amp When Speaker Select is set to External Speaker you should use these settings TV speaker Off External speaker On amp When Speaker Select is set to TV Speaker you should use these settings TV speaker On External speaker On amp If there is no video signal both speakers will be mute Additional Setting digital channels only E DTV Audio Level MPEG HE AAC This function allows you to reduce the disparity of a voice signal which is one of the signals received during a digital TV broadcast to a desired level Qy According to the type of broadcast signal MPEG HE AAC can be adjusted between 10dB and OdB To increase or decrease the volume adjust between the range 0 and 10 respectively E SPDIF Output SPDIF Sony Philips Digital InterFace is used to provide digital sound reducing interference going to speakers and various digital devices such as a DVD player Audio Format During the reception of a digital TV broadcast you ca
13. slanted wall it may fall and result in severe personal injury NOTE Samsung is not liable for product damage or personal injury when a non VESA or non specified wall mount is used or the consumer fails to follow the product installation instructions Standard dimensions for wall mount kits are shown in the table below e When purchasing our wall mount kit a detailed installation manual and all parts necessary for assembly are provided Do not use screws longer than the standard dimension as they may cause damage to the inside of the TV set For wall mounts that do not comply with the VESA standard screw specifications the length of the screws may differ depending on their specifications Do not use screws that do not comply with the VESA standard screw specifications Do not fasten the screws too strongly this may damage the product or cause the product to fall leading to personal injury Samsung is not liable for these kinds of accidents Samsung is not liable for product damage or personal injury when a non VESA or non specified wall mount is used or the consumer fails to follow the product installation instructions Our 57 and 63 models do not comply with VESA Specifications Therefore you should use our dedicated wall mount kit for this model Do not exceed 15 degrees tilt when mounting this TV UOIPEULIOJU JOUIO GO pai inches VESA Spec A B Standard Screw Quantit
14. the TV is turned on by Timer The TV will be automatically turned off after 3 hours of being left idle to prevent overheating i Locking Programs Security amp The PIN input screen appears before the setup screen Enter your 4 digit PIN the default of which is 0 0 0 0 Change the PIN using the Change PIN option BH Child Lock Off On Lock channels in Channel Manager to prevent unauthorized users such as children from watching unsuitable programme Available only when the Input source is set to TV H Parental Lock Parental Rating Prevent unauthorized users such as children from watching unsuitable programme with a user defined 4 digit PIN code If the selected channel is locked the f symbol will be displayed Allow All Unlock all TV ratings The items of Parental Lock differs depending on the country Change PIN Change your personal ID number required to set up the TV A it you forget the PIN code press the remote control buttons in the following sequence which resets the PIN to 0 0 0 0 POWER off gt MUTE gt 8 gt 2 gt 4 POWER on D Other Features Language Menu Language Set the menu language Teletext Language Set a desired language for teletext S English is the default in cases where the selected language is unavailable in the broadcast Preference Primary Audio Language Secondary Audio Language Primary Subtitle Language Secondary Sub
15. the repair or at its discretion replacement of the product or the defective part 3 Warranty repairs must be carried out by Authorised Samsung Dealers or Authorised Service Centres No re imbursement will be made for repairs carried out by non Samsung Dealers and any such repair work and damage to the products caused by such repair work will not be covered by this warranty 4 This product is not considered to be defective in materials nor workmanship by reason that it requires adaptation in order to conform to national or local technical or safety standards in force in any Country other than the one for which the product was originally designed and manufactured This page ts intention ally left blank
16. the source list e This is normal PC is always shown on the source list regardless of whether a PC is connected even if a PC is not connected The video is OK but there is no audio e If you are using a HDMI connection check the audio output setting on your PC Others The picture will not display in full screen e HD channels will have black bars on either side of the screen when displaying upscaled SD 4 3 contents e Black bars on the top and bottom will appear during movies that have aspect ratios different from your TV e Adjust the picture size options on your external device or TV to full screen The remote control does not work e Replace the remote control batteries with the poles in the right direction e Clean the sensor s transmission window on the remote e Try pointing the remote directly at the TV from 5 6 feet away The cable set top box remote control e Programme the Cable Set top box remote control to operate the TV Refer to the Cable Set user does not turn the TV on or off or adjust the volume manual for the SAMSUNG TV code A Not Supported Mode message e Check the supported resolution of the TV and adjust the external device s output resolution appears accordingly Refer to the resolution settings on page 22 of this manual There is a plastic smell from the TV e This smell is normal and will dissipate over time The TV Signal Information is unavailable in the Self Diagn
17. use the remote control when you are configuring Anynet or switching to a view mode Anynet device appears onthe e Use the remote control when the Anynet setting or switching to view mode is complete screen The Anynet device does not play e You cannot use the play function when Plug amp Play Initial setup is in progress The connected device is not e Check whether or not the device supports Anynet functions displayed e Check whether or not the HDMI Cable is properly connected e Check whether Anynet HDMI CEC is set to On in the Anynet setup menu e Search Anynet devices again e You can connect an Anynet device using the HDMI Cable only Some HDMI cables may not support Anynet functions e If it is terminated by an abnormal situation such as disconnecting the HDMI cable or power cord or a power failure please repeat the device scan The TV programme cannot be e Check whether the antenna jack on the recording device is properly connected recorded The TV sound is not output e Connect the optical cable between TV and the receiver through the receiver English 3 1 Other Information Analogue Channel Teletext Feature The index page of the Teletext service gives you information on how to use the service For Teletext information to be displayed correctly channel reception must be stable Otherwise information may be missing or some pages may not be displayed amp You can change Teletext pages by pressing the
18. v Move Enter 9 Return E Colour Tone Cool Normal Warm1 Warm2 amp Warmi or Warm2 will be deactivated when the picture mode is Dynamic amp Settings can be adjusted and stored for each external device connected to an input on the TV E Size Your cable box satellite receiver may have its own set of screen P SIZE sizes as well However we highly recommend you use 16 9 mode most of the time Auto Wide Automatically adjusts the picture size to the 16 9 aspect ratio 16 9 Adjusts the picture size to 16 9 for DVDs or wide broadcasting Wide Zoom Magnifies the picture size more than 4 3 amp Adjusts the Position by using A VW buttons Zoom Magnifies the 16 9 wide pictures vertically to fit the screen size Adjusts the Position or Size by using A Y button 4 3 The default setting for a movie or normal broadcasting Do not watch in 4 3 format for a long time Traces of borders displayed on the left right and centre of the screen may cause image retention screen burn which are not covered by the warranty Screen Fit Displays the full image without any cut off when HDMI 720p 1080i 1080p or Component 1080i 1080p signals are inputted NOTE e After selecting Screen Fit in HDMI 720p 1080i 1080p or Component 1080i 1080p mode you may need to center the picture 1 Press the lt or gt button to select Position 2 Press the ENTER C button 3 Pre
19. 10 10 12 13 16 18 20 Advanced Features 22 23 29 Other Information 32 This function can be used by pressing the TOOLS button on the remote control 33 34 34 35 38 39 Accessories Viewing the Control Panel Viewing the Remote Control Connecting to an Antenna Plug amp Play Initial Setup Connecting to an AV Device Connecting to an Audio Device Changing the Input Source How to Navigate Menus Using the INFO button Now amp Next guide Planning Your Viewing Channel Menu Picture Menu Sound Menu Setup Menu Support Menu Connecting to a PC Media Play Anynet Analogue Channel Teletext Feature Installing the Wall Mount Anti Theft Kensington Lock Securing the TV to the Wall Troubleshooting Specifications Index Check the Symbol Q One Touch Button English 3 Getting Started Accessories Please make sure the following items are included with your LCD TV If any items are missing contact your dealer amp The items colours and shapes may vary depending on the models e Remote Control amp Batteries AAA x 2 e Cleaning Cloth e Owner s Instructions e Power Cord See separate guide for installing the stand 3 Gm 4x16 e Stand 1EA e Screws SEA Viewing the Control Panel The product colour and shape may vary depending on the model Remote control sensor Power Indicator SOURCE Menue a FY CHA e S
20. AMSUNG Speakers Power Turns the TV on or off Power Indicator Blinks and turns off when the power is on and lights up in standby mode SOURCE Toggles between all the available input sources In the on screen menu use this button as you would use the ENTER C button on the remote control MENU Displays an on screen menu the OSD on screen display of your TV s features Adjusts the volume In the OSD use the Lf buttons as you would use the a lt and gt buttons on the remote control V CHA Changes the channels In the OSD use the Y CH A buttons as you would use the V and A buttons on the remote control Remote control sensor Aim the remote control towards this spot on the TV Standby mode Do not leave your TV in standby mode for long periods of time when you are away on a holiday for example A small amount of electric power is still consumed even when the power button is turned off It is best to unplug the power cord 4 English Viewing the Remote Control Turns the TV on and off P 6 Press to directly access to channels Alternately selects Teletext Double or Mix Adjusts the volume Display the main on screen menu P 9 Views the Media play P 23 Quickly selects frequently used functions Returns to the previous menu Buttons in the Channel Manager Media Play menu etc P MODE Selects picture mode P 13 S MODE Selects the sound mode P 16 DUAL Selects sound mode P 17
21. Contact SAMSUNG WORLDWIDE If you have any questions or comments relating to Samsung products please contact the SAMSUNG customer care centre Country Customer Care Centre T Web Site EIRE 0818 717100 www samsung com ie U K 0845 SAMSUNG 7267864 www samsung com uk 2010 Samsung Electronics Co Ltd All rights reserved BN68 02592D 01 imagine the possibilities Thank you for purchasing this Samsung product To receive more complete service please register your product at www samsung com register Model Serial No SERIES Figures and illustrations in this User Manual are provided for reference only and may differ from actual product appearance Product design and specifications may be changed without notice Digital TV notice 1 Functionalities related to Digital TV DVB are only available in countries areas where DVB T MPEG2 and MPEG4 AVC digital terrestrial signals are broadcasted or where you are able to access to a compatible DVB C MPEG2 and MPEG4 AAC cable TV service Please check with your local dealer the possibility to receive DVB T or DVB C signal DVB T is the DVB European consortium standard for the broadcast transmission of digital terrestrial television and DVB C is that for the broadcast ransmission of digital TV over cable However some differentiated features like EPG Electric Programme Guide VOD Video On Demand and so on are not included in this specification So
22. Settings menu a pop up message will appear when you resume play a movie file Sk sum D Play continuously 4 Pause lt gt Jump 1 Tools 5 Return Music Playing a Music 1 Press the lt or gt button to select Music then press the ENTERC button in the Media Play menu Press the lt gt A button to select the desired Music in the file list Press the ENTER C button or gt Play button During music playback you can search using lt and gt button 44 REW and gt FF buttons do not function during play Qy Only displays files with the MPS file extension Other file extensions are not displayed even if they are saved on the same USB device amp If the sound is strange when playing MP3 files adjust the Equalizer in the Sound menu An over modulated MP3 file may cause a sound problem 01 10 04 02 4 Pause lt gt Jump 4 Tools D Return Photos Viewing a Photo or Slide Show 1 Press the lt or gt button to select Photos then press the ENTERC button in the Media Play menu 2 Press the lt A button to select the desired photo in the file list 3 Press the ENTER C button or gt Play button While a photo list is displayed press the Play ENTER C button on the remote control to start slide show All files in the file list section will be displayed in the slide show During the slide show files are displaye
23. You can start or stop a Slide Show Start Slide Show Slide Show Speed You can select the slide show speed during the slide show v Background Music You can set and select background music when watching a Slide Show v Zoom You can zoom into images in full screen mode v Rotate You can rotate images in full screen mode v Information You can see detailed information about the played file v v v Settings Using the Setup Menu H Cont movie play help resume play On Off Select to display the help pop up message for continuous movie playback E Get the DivX VOD registration code Shows the registration code authorized for the TV If you connect to the DivX web site and register the registration code with a personal account you can download VOD registration file If you play the VOD registration using Media Play the registration is completed amp For more information on Divx VOD visit www DivX com E Get the DivX VOD deactivation code When DivX VOD is not registered the registration deactivation code is displayed If you execute this function when DivX VOD is registered the current DivX VOD registration is deactivated E Information Select to view information about the connected device 28 English Anynet g What is Anynet 2 Anynet is a function that enables you to control all connected Samsung devices that support Anynet with your Samsung TV s 5 remote The Anynet
24. alth from uncontrolled waste disposal please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take these items E for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product and its electronic accessories should not be mixed with other commercial wastes for disposal Correct disposal of batteries in this product Applicable in the European Union and other European countries with separate battery return systems This marking on the battery manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life Where marked the chemical symbols Hg Cd or Pb indicate that the battery contains mercury cadmium or lead above the reference levels in EC Directive 2006 66 If batteries are not properly disposed of these substances can cause harm to human health or the environment To protect natural resources and to promote material reuse please separate batteries from other types of waste and recycle them through your local free battery return system 2 English Contents Getting Started 4 4 5 6 6 Connections 7 8 9 Basic Features 9
25. aution Pulling pushing or climbing onto the TV may cause the TV to fall In particular ensure that your To avoid the TV from falling Since the necessary clamps screws and string are not supplied please purchase these additionally 1 Drive the screws into the clamps and firmly fasten them onto the wall Make sure the screws are firmly fixed into the wall Screw Specifications e Fora 17 29 Inch LCD TV M4 For a32 40 Inch LCD TV M6 2 Remove the screws from the centre back of the TV put the screws into the clamps and then fasten the screws onto the TV again 3 Connect the clamps fixed onto the TV and the clamps fixed onto the wall with a strong string and then tie the string tightly amp Verify all connections are properly secured Periodically check connections for any sign of fatigue for failure If you have any doubt about the security of your connections contact a professional installer amp install the TV near to the wall so that it does not fall backwards It is safe to connect the string so that the clamps fixed on the wall are equal to or lower than the clamps fixed on the TV untie the string before moving the TV 34 English Troubleshooting If you have any questions about the TV first refer to this list If none of these troubleshooting tips apply please visit www samsung com then click on Support or contact the call centre listed on the back cover of this manual
26. available only when the Input source is set to TV amp To return to the previous step press the red button 1 Selecting a language Press the A or W button then press the ENTER C button Select the desired OSD On Screen Display language 2 Selecting Store Demo Press the lt or gt button then press the ENTER C button or Home Use e Select the Home Use mode Store Demo Mode is for retail environments e Return the unit s settings from Store Demo to Home Use standard Press the volume button on the TV When the OSD volume is displayed press and hold MENU for 5 sec 3 Selecting a country Press the A or Y button then press the ENTER C button Select the appropriate country If the desired country does not exist on the menu select Others After selecting the country in the Country menu some models may proceed with an additional option to setup the pin number amp When you input the PIN number 0 0 0 0 is not available Selecting an antenna Press the A or Y button then press the ENTER C button Select Air or Cable Selecting a channel Press the A or V button then press the ENTER C button Select the channel source to memorise When setting the antenna source to Cable a step appears allowing you to assign numerical values channel frequencies to the channels For more information refer to Channel Auto Store P 12 oa e Press the ENTER C button at any time to interrupt the memorisation process 6 Se
27. ble only in HDMI mode RGB signals E Film Mode Off Auto1 Auto2 Sets the TV to automatically sense and process film signals from all sources and adjust the picture for optimum quality Available in TV AV COMPONENT 480i 1080i and HDMI 480i 1080 E Auto Protection Time 2 hours 4 hours 8 hours 10 hours Off If the same image remains on the screen Auto Screen Burn Protector will work sounyeoy oiseg 0 Picture Reset OK Cancel Resets your current picture mode to its default settings a Setting up the TV with Your PC Set the input source to PC Auto Adjustment Adjust frequency values positions and fine tune the settings automatically amp Not available when connecting through HDMI DVI cable English 1 5 Basic Features Screen H Coarse Fine Removes or reduces picture noise If the noise is not removed by Fine tuning alone then adjust the frequency as best as possible Coarse and Fine tune again After the noise has been reduced readjust the picture so that it is aligned to the centre of screen H Position Adjust the PC screen position with direction button A V lt gt E Image Reset Resets the image to default settings Using Your TV as a Computer PC Display Setting Up Your PC Software Based on Windows XP Depending on the version of Windows and the video card the actual screens on your PC may differ in which case the same basic set up information will a
28. d in order from currently being shown amp Music files can be automatically played during the Slide Show if the Ui EAs DIRS Sate BUI SO Background Music is set to On amp The BGM Mode cannot be changed until the BGM has finished loading 26 English i Playing the multiple files Playing the selected video music photo files 1 Press the Yellow button in the file list to select the desired file 2 Repeat the above operation to select multiple files amp NOTE The v mark appears to the left of the selected files e To cancel a selection press the yellow button again e To deselect all selected files press the TOOLS button and select Deselect All 3 Press the gt Play ENTER C button BE SUM JA Change Device iSelect ID Sorting 72 Tools 2files selected 1 1 Page Jan 10 2010 Jan 10 2010 Playing the video music photo file group 1 While a file list is displayed move to the any file in desired group 2 Press the TOOLS button and select Play Current Group a Media Play Additional Function Sorting the file list Press the blue button in the file list to sort the files Category Operation Videos Music Photos Basic View Displays the whole folder You can view the photo by selecting the folder v v v Title Sorts and displays the file title in Symbol Number Alphabet Special order v v v 5 Preference Sorts and displays the file by preference Y
29. d to the terminal marked with the letter N or coloured BLUE or BLACK The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED WARNING DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS MARKED WITH THE LETTER E OR BY THE EARTH SYMBOL OR COLOURED GREEN OR GREEN AND YELLOW Warranty Card NZ AN UNITED KINGDOM This Samsung product is warranted for a period of twelve 12 months from the original date of purchase against defective materials and workmanship In the event that warranty service is required you should return the product to the retailer from whom it was purchased However Samsung Authorised Dealers and Authorised Service Centres in other EC Countries will comply with the warranty on the terms issued to purchasers in the country concerned In case of difficulty details of our Authorised Service Centres are available from Samsung Electronics U K Ltd Customer Care Centre PO Box 17243 Edinburgh EH11 4YB United Kingdom Tel 0870 SAMSUNG 7267864 UK amp Northern Ireland Tel 0818 717 100 EIRE Only Fax 44 0845 650 8080 Web www samsung com WARRANTY CONDITIONS 1 The warranty is only valid if when warranty service is required the warranty card is fully and properly completed and is presented with the original invoice or sales slip or confirmation and the serial number on the product has not been defaced 2 Samsung s obligations are limited to
30. em Analogue PAL SECAM NTSC 4 43 NTSC 3 58 PALGO Digital MPEG 2 MP ML MPEG 4 H 264 AVC MP L3 MP L4 0 HP L4 0 Sound System BG OK NICAM MPEGI HDMI IN 1 3 Video 1080 24p 1080p 1080i 720p 576p 576i 480p 480i Audio Two Channel Linear PCM 32 44 1 48 kHz 16 20 24bits Analogue audio input HDMI IN1 only PC Input Stand Swivel Left Right 20 20 Model Name LE26C450 LE32C0450 Screen Size Diagonal 26 inch 32 inch Sound Output 5WX2 10W X2 Dimensions WxDxH Body 646 5 X 77 0 X 432 3 mm 784 4 X 76 2 X 514 2 mm With stand 646 5 X 222 2 X 477 3 mm 784 4 X 247 2 X 560 0 mm Weight Body 6 2 kg 9 1 kg With Stand 6 8 kg 9 6 kg Qy Design and specifications are subject to change without prior notice amp For the power supply and power consumption refer to the label attached to the product 38 English a A H S S Amplify 16 HDMI 7 29 Select All 13 Antenna 12 Headphones 8 Self Diagnosis 20 Anynet 29 Home Theatre 8 29 Sharpness 13 3 Audio Out 8 29 Signal Information 20 Auto Adjustment 15 Sleep Timer 18 z Auto Volume 17 i Slide Show 26 Installation Space 2 Software Upgrade 20 B Source List 9 i L Speaker Select 17 Background Music 27 7 T Specifications 38 Balance L R 16 anguage St pats Licence 37 andby mode 4 Basic View 27 Subtitle 19 Lock 13 Batteries 5 Symbol 3 Black Tone 14 Blanking Bracket 33 M T Brightness 13 Media Play 23 Melody ig Timer 18 C Menu Transpar
31. ency 19 n i ools Change PIN 6 19 sacs Troubleshooting 35 Channel Manager 11 TV Speaker 17 Clock 18 N Colour Tone 15 Navigate 9 U Component 7 Now amp Next guide 10 Connecting to a PC 22 USB 20 23 Connecting to an Audio Device 8 o Using Channel View 10 Using Scheduled View 10 D ON OFF button 5 Using the Favourite Channels 11 Optimal resolution 22 Digital Audio Out 8 29 y DivxX VOD 28 P D sub 22 VCR 9 Dynamic 13 Photos 26 Video Formats 25 Dynamic Contrast 14 Picture Size 15 27 Videos 24 PIP Picture in Picture 20 Volume 4 5 17 E Plug amp Play 6 Power Indicator 4 W Edit Name 9 Editing Channels 12 R Wall Mount 33 Energy Saving 14 Warm 14 Equalizer 16 Receiver 31 White Balance 14 External Speaker 17 Recording 30 EPG 10 Remote Control 5 Repeat Mode 27 F RGB Only Mode 14 Rotate 28 Favourites Channel 11 Film Mode 15 Fine Tune 13 Flesh Tone 14 Frequency 12 English 39 Warning Important Safety Instructions Please read the appropriate section that corresponds to the marking on your Samsung product before attempting to install the product is symbol indicates that high voltage is CAUTION present inside It is dangerous to make any kind of contact with any internal part of this product RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK THERE ARE NO This symbol alerts you that important literature USER SERVICEABLE PARTS INSIDE REFER ALL SERVIC
32. game console such as PlayStation or Xbox you can enjoy amore realistic gaming experience by selecting game mode NOTE e Precautions and limitations for game mode To disconnect the game console and connect another external device set Game Mode to Off in the setup menu If you display the TV menu in Game Mode the screen shakes slightly Game Mode is not available in TV and PC mode e After connecting the game console set Game Mode to On to prevent poor picture quality If Game Mode is On Picture mode is set to Standard and Sound mode is set to Custom Menu Transparency Bright Dark Set the Transparency of the menu Melody Off Low Medium High Set so that a melody plays when the TV is turned on or off Common Interface Cl Menu This enables the user to select from the CAM provided menu Select the Cl Menu based on the menu PC Card Application Info View information on the CAM inserted into the Cl slot and on the Cl or Cl CARD which is inserted into the CAM You can install the CAM anytime whether the TV is on or off Purchase a Cl CAM module at your nearest dealer or by phone Firmly insert the Cl or Cl CARD into the CAM in the direction of the arrow Insert the CAM with the Cl or Cl CARD into the common interface slot in the direction of the arrow so that it aligns parallel with the slot Check if you can see a picture on a scrambled signal channel English 19
33. he PIP menu is not available PIP functionality is only available when you are using a HDMI PC or components source The message Scramble signal or Weak Signal No Signal appears If you are using a CAM CARD CI Cl check that it is installed into the common interface slot If there is still a problem pull the CAM CARD out of the TV and insert it into the slot again You turned the TV off 45 minutes ago and it turned on again It is normal The TV operates the OTA Over The Aerial function itself to upgrade firmware downloaded whilst your watching TV There are recurrent picture sound issues Check and change the signal source A reaction may occur between the rubber cushion pads on the base stand and the top finish of some furniture To prevent this use felt pads on any surface of the TV that comes in direct contact with furniture This TFT LCD panel uses a panel consisting of sub pixels which require sophisticated technology to produce However there may be a few bright or dark pixels on the screen These pixels will have no impact on the performance of the product fil Licence PULSE pe DOLBY Manufactured under licence from Dolby Laboratories Dolby and the double D symbol are _DIGITAL PLUS trademarks of Dolby Laboratories Manufactured under license under U S Patent s 5 451 942 5 956 674 5 974 380 5 978 762 6 487 535 amp other U S and worldwide patents is
34. he Speaker Select option to TV speaker in the sound menu P 17 e If you are using an external device make sure the audio cables are connected to the correct audio input jacks on the TV e If you are using an external device check the device s audio output option ex you may need to change your cable box s audio option to HDMI when you have a HDMI connected to your TV e If you are using a DVI to HDMI cable a separate audio cable is required e If your TV has a headphone jack make sure there is nothing plugged into it The speakers are making an inappropriate noise e Check the cable connections Make sure a video cable is not connected to an audio input e For antenna or cable connections check the signal strength Low signal level may cause sound distortion English 3 5 Other Information Issues Solutions and Explanations No Picture No Video The TV will not turn on e Make sure the AC power cord is securely plugged in to the wall outlet and the TV e Make sure the wall outlet is working e Try pressing the POWER button on the TV to make sure the problem is not the remote If the TV turns on refer to The remote control does not work below The TV turns off automatically Ensure the Sleep Timer is set to Off in the Setup menu P 18 If your PC is connected to the TV check your PC power settings Make sure the AC power cord is plugged in securely to the wall outlet and the TV When watching
35. hen the Input source is set to TV English 1 7 sounjyes j dIseg 0 Basic Features a O fi Setting the Time Time H Clock Setting the clock is for using various timer features of the TV The current time will appear every time you press the INFO button A it you disconnect the power cord you have to set the clock again Clock Mode Auto Manual S Depending on the broadcast station and signal the auto time set up may not be correct In this case set the time manually amp The antenna must be connected in order to set the time automatically Clock Set Set the Day Month Year Hour and Minute manually amp Available only when Clock Mode is set to Manual Time Zone You can select your time zone This feature is only available in Australia amp Q This function is only available when Clock Mode is set to Auto amp Depending on the broadcast station and signal the auto time may not be set correctly If this occurs set the time manually fl Using the Sleep Timer E Sleep Timer Automatically shuts off the TV after a preset period of time 30 60 90 120 150 and 180 minutes To cancel Sleep Timer select Off D Setting the On Off Timer E Timer 1 Timer 2 Timer 3 Three different on off timer settings can be made You must set the clock first On Time Off Time isi Volume Source Antenna k m Hl a i ay a ae L i i J Repeat Once Channel Su
36. ion of channel information has finished the message Updating Completed is displayed indicating the channel list is updated n 8 z gt a E f NOTE e You must obtain a Cl or Cl CARD from a local cable service provider When removing the Cl or Cl CARD carefully pull it out with your hands since dropping the Cl or Cl CARD may cause damage to it Insert the Cl or Cl CARD in the direction marked on the card The location of the COMMON INTERFACE slot may be different depending on the model Cl or Cl CARD is not supported in some countries and regions check with your authorized dealer If you have any problems please contact a service provider 8 English Changing the Input Source Edit Name o D E VCR DVD Cable STB Satellite STB PVR STB O Source List AV Receiver Game Camcorder PC DVI PC DVI 2 Devices TV IPTV Blu ray HD DVD DMA Name a Use to select TV or other external input SOURCE the device connected to the input jacks to make your Q sources such as DVD Blu ray players input source selection easier g ei K s SNE selina TEGEV ee ae 3 amp When connecting an HDMI DVI cable to the HDMI i IN 1 DVI port you should set to DVI PC or DVI E TV Ext AV Component PC yyt Devices mode under Edit Name HDMI1 DVI HDMI2 HDMI3 USB amp Q Inthe Source List connected inputs will be highlighted Basic Feature
37. k room D Adjusting picture settings Backlight Contrast Brightness Sharpness Colour Tint G R Your television has several setting options for picture quality control NOTE In analogue TV Ext AV modes of the PAL system the Tint G R function is not available In PC mode you can only make changes to Backlight Contrast and Brightness Settings can be adjusted and stored for each external device connected to the TV Lowering picture brightness reduces power consumption English 13 Basic Features fi Economical Solutions ECO Solution E Energy Saving Off Low Medium High Picture Off Auto Adjust the brightness of the TV in order to reduce power consumption If you select Picture Off the screen is turned off but the sound remains on Press any button except volume button to turn on the screen E No Signal Power Off Off 15 min 30 min 60 min Activates the Stand by mode in the case of No Signal or Check Signal Cable status for a certain period of time defined by the user Disabled when the PC is in power saving mode i Changing the Picture Options Advanced Settings available in Standard Movie mode You can adjust the detailed setting for the screen including colour and contrast in Pc mode you can only make changes to Dynamic Contrast Gamma and White Balance Advanced Settings Black Tone Off gt Dynamic Contrast Mediu
38. k to the product If the product is damaged disconnect the power cord and contact a service center WARNING TO PREVENT THE SPREAD OF FIRE KEEP CANDLES OR OTHER OPEN FLAMES AWAY FROM THIS PRODUCT AT ALL TIMES Wiring the Mains Power Supply Plug UK Only IMPORTANT NOTICE The mains lead on this equipment is supplied with a moulded plug incorporating a fuse The value of the fuse is indicated on the pin face of the plug and if it requires replacing a fuse approved to BSI1362 of the same rating must be used Never use the plug with the fuse cover omitted if the cover is detachable If a replacement fuse cover is required it must be of the same colour as the pin face of the plug Replacement covers are available from your dealer If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a power point you should obtain a suitabl y approved extension lead or consult your dealer for assistance However if there is no alternative but to cut off the plug remove the fuse and then safely dispose of the plug Do NOT connect the plug to a mains socket as there is a risk of shock hazard from the bared flexible cord IMPORTANT The wires in the mains lead are coloured in accordance with the following code BLUE NEUTRAL BROWN LIVE As these colours may not correspond to the coloured markings identifying the terminals in your plug proceed as follows The wire coloured BLUE must be connecte
39. l audio is available when the TV is connected to an external device supporting 5 1 CH e When the receiver home theatre is set to on you can hear sound output from the TV s optical jack When the TV is receiving a DTV signal the TV will send 5 1 CH sound to the home theatre receiver When the source is a digital component such as a DVD Blu ray player cable box STB Set Top Box satellite receiver and is connected to the TV via HDMI only 2 CH audio will be heard from the home theatre receiver If you want to hear 5 1 CH audio connect the digital audio out jack from your DVD Blu ray player cable box STB satellite receiver directly to an amplifier or home theatre amp Headphones A You can connect your headphones to the headphones output on your set While the headphones are connected the sound from the built in speakers will be disabled Sound function may be restricted when connecting headphones to the TV e Headphone volume and TV volume are adjusted separately CONNECTIONS COMMON INTERFACE Slot To watch paid channels the Cl or Cl CARD must be inserted If you do not insert the Cl or Cl CARD some channels will display the message Scrambled Signal The pairing information containing a telephone number the Cl or Cl CARD ID the Host ID and other information will be displayed in about 2 3 minutes If an error message is displayed please contact your service provider When the configurat
40. le match e Reduce brightness and contrast values to minimum required to achieve desired picture quality exceeded values may speed up the burnout process e Frequently use all TV features designed to reduce image retention and screen burnout refer to proper user manual section for details P p e grr Securing the Installation Space Keep the required distances between the product and other objects e g walls to ensure proper ventilation Failing to do so may result in fire or a problem with the product due to an increase in the internal temperature of the product amp When using a stand or wall mount use parts provided by Samsung Electronics only Ifyou use parts provided by another manufacturer it may result in a problem with the product or an injury due to the product falling amp The appearance may differ depending on the product Installation with a stand Installation with a wall mount Correct Disposal of This Product Waste Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection systems This marking on the product accessories or literature indicates that the product and its electronic accessories e g charger headset USB cable should not be disposed of with other household waste at the end of their working life To prevent possible harm to the environment or human he
41. lect is set to External Speaker or the sound is muted by pressing the MUTE button 20 English E Signal Information digital channels only HDTV channel s reception quality is either perfect or the channels are unavailable Adjust your antenna to increase signal strength Troubleshooting If the TV seems to have a problem refer to this description amp Q If none of these troubleshooting tips apply contact the Samsung customer service centre Software Upgrade Software Upgrade can be performed via a broadcasting signal or by downloading the latest firmware from samsung com to a USB memory device Current Version the software already installed in the TV W Software is represented as Year Month Day_Version Software Upgrade Current Version 2010 01 18 000001 By USB gt By Channel Standby Mode Upgrade Off Alternative Software _ Move Enter 5 Return Installing the Latest Version E By USB Insert a USB drive containing the firmware upgrade file downloaded from www samsung com into the TV Please be careful not to disconnect the power or remove the USB drive until upgrades are complete The TV will be turned off and on automatically after completing the firmware upgrade When software is upgraded video and audio settings you have made will return to their default settings We advise you to write down your settings so that you can easily reset them after the upgrade
42. lmost always be applied If not contact your computer manufacturer or Samsung Dealer 1 Click on Control Panel on the Windows start menu 2 Click on Appearance and Themes in the Control Panel window and a display dialog box will appear 3 Click on Display and a display dialog box will appear Navigate to the Settings tab on the display dialog box e The correct size setting resolution Optimum 1360 X 768 pixels e f a vertical frequency option exists on your display settings dialog box the correct value is 60 or 60 Hz Otherwise just click OK and exit the dialog box Changing the Preset Sound Mode Mode E Standard Selects the normal sound mode s moe HM Music Emphasizes music over voices MH Movie Provides the best sound for movies E Clear Voice Emphasizes voices over other sounds H Amplify Increase the intensity of high frequency sound to allow a better listening experience for the hearing impaired 1 6 English Adjusting sound settings Equalizer Adjusts the sound mode E Balance L R Adjusts the balance between the right and left speaker HM 100Hz 300Hz 1kHz 3kHz 10kHz Bandwidth Adjustment Adjusts the level of specific bandwidth frequencies E Reset Resets the equalizer to its default settings D Sound Systems Etc Virtual Surround Off On This function provides a virtual 5 1 channel surround sound experie
43. m Shadow Detail 10 Gamma 0 RGB Only Mode Off Colour Space Native White Balance v Move Enter Return E Black Tone Off Dark Darker Darkest Select the black level to adjust the screen depth E Dynamic Contrast Off Low Medium High Adjust the screen contrast H Shadow Detail 2 2 Increase the brightness of dark images amp Disabled under PC mode E Gamma Adjust the primary colour intensity H RGB Only Mode Off Red Green Blue You can adjust Colour or Tint of Red Green or Blue for the picture from an external device DVD player home theatre etc H Colour Space Auto Native Adjust the range of colors available to create the image 14 English White Balance Adjust the colour temperature for a more natural picture R Offset G Offset B Offset Adjust each colour s red green blue darkness R Gain G Gain B Gain Adjust each colour s red green blue brightness Reset Resets the White Balance to it s default settings Flesh Tone Emphasize pink Flesh Tone Edge Enhancement Off On Emphasize object boundaries Picture Options In Pc mode you can only make changes to the Colour Tone Size Digital Noise Filter and Auto Protection Time Picture Options Colour Tone Normal gt Size 16 9 Screen Mode 16 9 Digital Noise Filter Auto MPEG Nosie Filter Auto HDMI Black Level Normal Film Mode Off
44. n Anynet Device to turn off automatically when the TV is turned off amp The active source on the TV must be set to TV to use the Anynet function Even if an external device is still recording it may turn off i Switching between Anynet Devices 1 Anynet devices connected to the TV are listed A it you cannot find a device you want press the red button to refresh the list 2 Select a device and press the ENTER C button You can switch to the selected device amp Only when you set Anynet HDMI CEC to On in the Application menu the Device List menu appears Switching to the selected device may take up to 2 minutes You cannot cancel the operation during the switching operation If you have selected external input mode by pressing the SOURCE button you cannot use the Anynet function Make sure to switch to an Anynet device by using the Device List J Recording You can make a recording of a TV programme using a Samsung recorder 1 Select Recording amp When there are more than two recording devices e When multiple recording devices are connected the recording devices are listed Select one recording device in the Device List Q when the recording device is not displayed select Device List and press the Red button to search devices 2 Press the EXIT button to exit amp You can record the source streams by selecting Recording device_name amp Pressing the Le REC button will record whatever
45. n Mon Tue Wed Thu Fri Sat 4 gt Move Adjust C Enter 5 Return 18 English On Time Off Time Set the hour minute and activate inactivate To activate timer with the setting you have chosen set to Activate Volume Set the desired volume level Source Select TV or USB content to be played when the TV is turned on automatically USB can be selected only when a USB device is connected to the TV Antenna when the Source is set to TV Select ATV or DTV Channel when the Source is set to TV Select the desired channel Contents when the Source is set to USB Select a folder in the USB device containing music or photo files to be played when the TV is turned on automatically amp Q amp if there is no music file on the USB device or the folder containing a music file is not selected the Timer function does not operate correctly Q When there is only one photo file in the USB device the Slide Show will not play amp Ifa folder name is too long the folder cannot be selected Each USB you use is assigned its own folder When using more than one of the same type of USB make sure the folders assigned to each USB have different names Repeat Select Once Everyday Mon Fri Mon Sat Sat Sun or Manual to set at you convenience If you select Manual you can set up the day you want to activate the timer The v mark indicates the day is selected amp Auto Power Off available only when
46. n select the Digital Audio output SPDIF format from the options PCM or Dolby Digital amp By connecting to 5 1ch speakers in a Dolby Digital setup maximize your interactive 3D sound experience Audio Delay Correct audio video mismatch when watching TV or video and listening to digital audio output using an external device such as an AV receiver E Dolby Digital Comp Line RF This function minimizes signal disparity between a dolby digital signal and a voice signal i e MPEG Audio HE AAC ATV Sound Select Line to obtain dynamic sound and RF to reduce the difference between loud and soft sounds at night time Line Set the output level for signals greater or less than 310B reference to either 20dB or 31dB RF Set the output level for signals greater or less than 200B reference to either 10dB or 20dB Sound Reset OK Cancel Reset all sound settings to the factory defaults fi Selecting the Sound Mode When you set to Dual I Il the current sound mode is displayed on the screen ae Dual I II Default Type rc Mono Mono Automatic Stereo Stereo Mono change Stereo Dual Dual Dual II Dual Mono Mono Automatic NICAM Stereo Mono e Stereo change Stereo oy Dual MOND a DURA Dual Dual Il lt amp if the stereo signal is weak and an automatic switching occurs then switch to the mono Qy Only activated in stereo sound signal Qy Only available w
47. nce through a pair of speakers or headphones using HRTF Head Related Transfer Function technology Af Speaker Select is set to External Speaker Virtual Surround is disabled Dialog Clarity Off On This function allows you to increase the intensity of a voice over background music or sound effects so that dialog can be heard more clearly when viewing a show Audio Language digital channels only Change the default value for audio languages The available language may differ depending on the broadcast Audio Format MPEG Dolby Digital 5 1 digital channels only When sound is emitted from both the main speaker and the audio receiver a sound echo may occur due to the decoding speed difference between the main speaker and the audio receiver In this case use the TV Speaker function amp Audio Format option may differ depending on the broadcast 5 1ch Dolby digital sound is only available when connecting an external speaker through an optical cable Audio Description not available in all locations digital channels only This function handles the Audio Stream for the AD Audio Description which is sent along with the Main audio from the broadcaster H Audio Description Off On Turn the audio description function on or off H Volume Adjust the audio description volume Auto Volume Off Normal Night To equalize the volume level on each channel set to Normal HM Night This mode
48. ng an HDMI cable check the HDMI version of the external device If you suspect the version is older than 1 3 contact the provider of the device to confirm the HDMI version and request an upgrade e It is recommended you purchase an HDMI certified cable Otherwise the screen may appear blank or a connection error may occur J Using a Component up to 1080p or Audio Video 480i only Cable and Using a Scart Cable Available devices VCR DVD Blu ray player cable box STB satellite receiver COMPONENT IN Yellow Red White AUDIO OUT BU SE AUDIO OUT COMPONENT OUT _ m ojc amp In Ext mode DTV Out supports MPEG SD Video and Audio only amp To obtain the best picture quality the Component connection is recommended over the A V connection J N O O d English 7 Connections Connecting to an Audio Device Using an Optical or Audio Cable Connection Available devices digital audio system amplifier DVD home theatre amp The product colour and shape may vary depending on the model Digital Audio AUDIO OU OPTICAL System Headphone amp DIGITAL AUDIO OUT OPTICAL e When a digital audio system is connected to the DIGITAL AUDIO OUT OPTICAL jack decrease the volume of both the TV and the system e 5 1 CH channe
49. nnels and press the Yellow button to set all the selected channels at the same time The YW mark appears to the left of the selected channels Blue Sort Change the list ordered by channel name or channel number Page Move to next or previous page AJ Tools Displays the Channel Manager option menu The Options menus may differ depending on the situation Channel Status Display Icons Icons Operations A An Analogue channel v A channel selected Yy A channel set as a Favourite am A programme currently being broadcast fa A locked channel A reserved programme T Using Favourite Channels My Channels in Channel Manager Shows all favourite channels E Edit My Channels You can set the selected channels to desired my channels group amp The Y symbol will be displayed and the channel will be set as a my channel 1 Select a channel and press the TOOLS button 2 Add or delete a channel in the my channel groups you want among 1 2 3 and 4 One or more groups can be selected 3 After you have changed the settings the channel list for each group can be viewed in My Channels v1 1futech V2 240re tv Edit My Channels 5 Lock Radio Delete Data Other 23 DERU 33 EEN Analogue sgjeuueyg Class News Coming Soon Discovery English 1 1 sounjyesyj dIseg 0 Basic Features ii Retuning channels Antenna Air Cable Before you
50. numeric buttons on the remote control o A Teletext on mir Activate the Teletext mode after selecting the channel providing the Teletext service Press it twice to overlap the Teletext mode with the current broadcasting screen 27 store Store the Teletext pages size Display the double size letters on the upper half of the screen For the lower half of the screen press it again To display the normal screen press it once again hold Hold the display on a given page if the selected page is linked with several secondary pages which follow on automatically To resume press it again 8 mode Select the Teletext mode LIST FLOF If you press this button in the LIST mode the mode is switched into the List save mode In the List save mode you can save a Teletext page into list using the Es store button Q sub page Display the available sub page oe ce aJJ 4J s Ce LILL E S SAMSUNG The Teletext pages are organized according to six categories page up Display the next Teletext page page down Display the previous Teletext page index Display the index contents page at any time while you are viewing Teletext reveal Display the hidden text answers to quiz games for example To display the normal screen press it again EX cancel Display the current broadcast when searching for a page
51. o display the channels you want E Select All Deselect All Select all the channels or deselect all the selected channels in the channel manager Scheduled in Channel Manager You can view modify or delete a show you have reserved to watch E Change Info Change a show you have reserved to watch E Cancel Schedules Cancel a show you have reserved to watch E Information Display a show you have reserved to watch You can also change the reservation information H Select All Deselect All Select or deselect all reserved programmes Channel List You can see all the channels searched CHLIST Channel List Transfer Imports or exports the channel map You should connect a USB storage to use this function amp The PIN number input screen appears Enter your 4 digit PIN number amp The default PIN number of a new TV set is 0 0 0 0 E Impor from USB Import channel list from USB E Export to USB Export channel list to USB sounyeoy oiseg 0 Fine Tune analogue channels only If the signal is weak or distorted fine tune the channel manually amp Fine tuned channels are marked with an asterisk To reset the fine tuning select Reset i Changing the Preset Picture Mode P mone Mode Select your preferred picture type H Dynamic Suitable for a bright room E Standard Suitable for a normal environment H Movie Suitable for watching movies in a dar
52. ostic Test menu This function is only available with digital channels from an Antenna RF Coax connection P 20 The TV is tilted to the side Remove the base stand from the TV and reassemble it There are difficulties assembling the stand base Make sure the TV is placed on a flat surface If you can not remove the screws from the TV please use a magnetized screw driver The channel menu is greyed out unavailable The Channel menu is only available when the TV source is selected 3 6 English Issues Solutions and Explanations Your settings are lost after 30 minutes or every time the TV is turned off If the TV is in the Store Demo mode it will reset audio and picture settings every 30 minutes Change the settings from Store Demo mode to Home Use mode in the Plug amp Play Initial setup procedure Press the SOURCE button to select TV mode and go to MENU Setup Plug amp Play Initial setup gt ENTER C You have intermittent loss of audio or video Check the cable connections and reconnect them Loss of audio or video can be caused by using overly rigid or thick cables Make sure the cables are flexible enough for long term use If mounting the TV to the wall we recommend using cables with 90 degree connectors You see small particles when you look closely at the edge of the frame of the TV This is part of the product s design and is not a defect T
53. ou can change the file preference in the file V list section using the Green button S Latest Date Sorts and shows files by the latest date v 7 5 Earliest Date Sorts and shows files by the earliest date v v Artist Sorts the music file by artist in alphabetical order v A Album Sorts the music file by album in alphabetical order v Genre Sorts music files by the genre v Mood Sorts music files by the mood You can change the music mood information v 7 Monthly Sorts and shows photo files by month v English 27 sounjes4j psdueApy 0 Advanced Features Videos Music Photos Play Option menu During playing a file press the TOOLS button Category Operation Videos Music Photos Title You can move the other file directly v Repeat Mode You can play movie and music files repeatedly v v Picture Size You can adjust the picture size to your preference P Mode1 Mode2 Original Picture Setting You can adjust the picture setting p 13 14 15 16 v v Sound Setting You can adjust the sound setting p 16 17 v v v Subtitle Setting You can play the video with Subtitles This function only works if the subtitles are the same file name as the video Audio You can enjoy video in one of supported languages as required The function is only a i v enabled when stream type files which support multiple audio formats are played Stop Slide Show
54. playing now or coming up Yellow 24 hours Viewing the list of programmes to be broadcasted after 24 hours D Blue Ch Mode Select the type of channels you want to display on the Channel View window The Ch Mode differs according to the antenna source Information Displays details of the selected programme Page Moves to the previous next page ENTER C button When selecting the current programme you can watch the selected programme When selecting the future programme you can reserve to watch the selected programme To cancel the schedule press the ENTER C button again and select Cancel Schedules Channel Manager Delete or set favourites channels and use the programme guide for digital broadcasts Select a channel in the Channels My Channels or Scheduled screen v1 1futech All v2 24ore tv gjauueyg BBC World bid up tv Radio 3 Data Other 23 Anal 33 Boonerang ogue 32 Cartoon Nwk 5 Class News Coming Soon Discovery W Antena ii Zoom W Select Wi Sort S Page J Tools E Channels Shows the channel list according to channel type m My Channels Shows the group of the channel E Scheduled Shows all the currently reserved programmes amp Using the colour buttons with the Channel Manager ARed Antenna Toggle among Air or Cable E Green Zoom Enlarges or shrinks a channel number E Yellow Select Select desired cha
55. r television can begin memorizing the available channels you must specify the type of signal source that is connected to the TV i e an Air or a Cable system Country The PIN input screen appears Enter your 4 digit PIN number E Digital Channel Change the country for digital channels H Analogue Channel Change the country for analogue channels Auto Store Scans for a channel automatically and stores in the TV amp Automatically allocated programme numbers may not correspond to actual or desired programme numbers If a channel is locked using the Child Lock function the PIN input window appears E Antenna Source Air Cable Select the antenna source to memorise H Channel Source Digital amp Analogue Digital Analogue Select the channel source to memorise When selecting Cable Digital amp Analogue or Digital Provide a value to scan for cable channels Search Mode Full Network Quick Scans for all channels with active broadcast stations and stores them in the TV A amp A it you set Quick you can set up Network Network ID Frequency Modulation Symbol Rate manually by press the button on the remote control Network Auto Manual Selects the Network ID setting mode among Auto or Manual Network ID When Network is Manual you can set up Network ID using the numeric buttons Frequency Displays the frequency for the channel differs in each country Modulation Displays available
56. roblems with the contents of a codec the codec will not be supported e If the information for a Container is incorrect and the file is in error the Container will not be able to play correctly Sound or video may not work if the contents have a standard bitrate frame rate above the compatible Fram sec listed in the table above e Ifthe Index Table is in error the Seek Jump function is not supported Video Decoder Audio Decoder Supports up to H 264 Level 4 1 H 264 FMO ASO RS VC1 SP MP AP L4 and AVCHD are not e supported H 263 is not supported GMC 2 over is not support Supports up to WMA 7 8 9 STD WMA 9 PRO does not support 2 channel excess multi channel or lossless audio WMA sampling rate 22050Hz mono is not supported English 25 sounjes4j psdueApy 0 Advanced Features Playing movie continuously Resume Play If you exit the playing movie function the movie can be played later from the point where it was stopped 1 Select the movie file you want to play continuously by pressing the E lt or P gt button to select it from the file list section lg 00 04 03 00 07 38 Movie 01 avi Press the gt Play ENTER C button Select Play Continuously Resume Play by pressing the Blue button The Movie will begin to play from where it was stopped amp Q amp The Blue button is available when resuming play amp ifthe Cont movie play help function is set to On in the
57. rtain the selected file name and the number of files and page Movie 02 avi pee ts au Jan 10 2010 ee 10 2010 File List Section Movie 05 avi Movie 06 a You can confirm the files and Jan 10 2010 groups that are sorted by Sort List Section category Displays the sorting standard amp The sorting standard is different depending on the contents Select Di Sorting 42 Tools Operation Buttons E Red Change Device Selects a connected device E Green Preference Sets the file preference not supported in Basic view Yellow Select Selects multiple files from file list Selected files are marked with a symbol E Blue Sorting Selects the sort list A1 Tools Displays the option menu amp Using the e4 or gt gt button file list can move to next or previous page Videos Playing a Video 1 Press the lt or gt button to select Videos then press the ENTER C button in the Media Play menu 2 Press the lt A button to select the desired video in the file list 3 Press the ENTER C button or gt Play button The selected file is displayed on the top with its playing time If video time information is unknown play time and progress bar are not displayed During video playback you can search using lt and gt button In this mode you can enjoy movie clips contained on a Game but you cannot play the Game itself e Supported Subti
58. s How to Operate the OSD On Screen Display Before using the TV follow the steps below to learn how to The access step may differ depending on the selected menu navigate the menu and select and adjust different functions The main menu options appears on the screen 0 WeDIAP menu cuine 1 MENU ur Picture Sound Channel Setup a Input Application Support ET lo Select an icon with the A or Y A Y button Press ENTER C to access the sub J s 2 f Q ENERG icn Select the desired submenu with a gt K 0 4 A V the A or Y button EX Adjust the value of an item with the 5 R lt or gt button The adjustment in the OSD may differ depending on MENU button Displays the main on screen menu the selected menu ENTER Direction button Move the cursor and 6 ENTERCe Press ENTERC to complete the select an item Confirm the setting configuration RETURN button Returns to the previous menu 7 Exit oss EXIT EXIT button Exits the on screen menu English 9 Basic Features The display identifies the current channel and the status of certain audio video settings The Now amp Next guide shows daily TV programme information for each channel according to the broadcasting time e Scroll lt gt to view information for a desired programme while watching the current channel e Scroll A Y to view information for other channels If you want to move to the currentl
59. sired D Other Features Cable Search Option depending on the country Sets additional search options such as the frequency and symbol rate for a cable network search E Freq Start Freq Stop Set the start or stop frequency differs in each country H Modulation Displays available modulation values H Symbol Rate Displays available symbol rates Channel Manager Option Menu in Channel Manager Set each channel using the Channel Manager menu options Lock Unlock Timer Viewing Sort Delete Select All Deselect All Option menu items may differ depending on the channel status 1 Select a channel and press the TOOLS button 2 Select a function and change its settings E Lock Unlock Lock a channel so that the channel cannot be selected and viewed NOTE e This function is available only when the Child Lock is set to On The PIN input screen appears Enter your 4 digit PIN the default of which is 0 0 0 0 Change the PIN using the Change PIN option E Timer Viewing You can set a desired channel to be displayed automatically at the intended time Set the current time first to use this function Q Whena digital channel is selected press the gt button to view the digital Programme E Sort analogue channels only This operation allows you to change the programme numbers of the stored channels This operation may be necessary after using the auto store E Delete You can delete a channel t
60. ss the A V lt or gt button to move the picture Depending on the input source the picture size options may vary The available items may differ depending on the selected mode e In PC mode only 16 9 and 4 3 modes can be adjusted Settings can be adjusted and stored for each external device connected to an input of the TV If you use the Screen Fit function with HDMI 720p input 1 line will be cut at the top bottom left and right as in the overscan function Screen Mode 16 9 Wide Zoom Zoom 4 3 Available only when picture size is set to Auto Wide You can determine the desired picture size at the 4 3 WSS Wide Screen Service size or the original size Each European country requires different picture size _ Not available in PC Component or HDMI mode E Digital Noise Filter Off Low Medium High Auto Auto Visualisation When the broadcast signal is weak some static and ghosting may appear Select one of the options until the best picture is displayed Auto Visualisation When changing analogue channels displays signal strength amp Only available for analogue channels Q When bar is green you are receiving the best possible signal E MPEG Noise Filter Off Low Medium High Auto Reduces MPEG noise to provide an improved picture quality amp Disabled under PC mode E HDMI Black Level Normal Low Selects the black level on the screen to adjust the screen depth Availa
61. sued amp pending DTS and the Symbol are 2 0 Digital Out registered trademarks amp DTS 2 0 Digital Out and the DTS logos are trademarks of DTS Inc Product Includes software DTS Inc All Rights Reserved DivX Certified to play DivX video up to HD 1080p including premium content ABOUT DIVX VIDEO DivX is a digital video format created by DivX Inc This is an official DivX Certified device that plays DivX video Visit www divx com for more information and software tools to convert your files into DivX video ABOUT DIVX VIDEO ON DEMAND This DivX Certified device must be registered in order to play DivX Video on Demand VOD content To generate the registration code locate the DivX VOD section in the device setup menu Go to vod divx com with this code to complete the registration process and learn more about DivX VOD Pat 7 295 673 7 460 688 7 519 274 Open source license notice n the case of using open source software Open Source Licenses are available on the product menu English 3 7 UOIPEULIOJU JOUIO SO Other Information Panel native 1360 X 768 60 Hz Environmental Considerations Operating Temperature 10 C to 40 C 50 F to 104 F Operating Humidity 10 to 80 non condensing Storage Temperature 20 C to 45 C 4 F to 113 F Storage Humidity 5 to 95 non condensing TV System Analogue Depending on your country selection Digital DVB T DVB C Colour video syst
62. th unlicensed multimedia files amp Need to Know List before using Media Play e MTP Media Transfer Protocol is not supported e The file system supports FAT16 FAT32 and NTFS e Certain types of USB Digital camera and audio devices may not be comp atible with this TV e Media Play only supports USB Mass Storage Class MSC devices MSC is a Mass Storage Class Bulk Only Transport device Examples of MSC are Thumb drives Flash Card Readers and USB HDD USB HUB are not supported Devices should be connected directly to the TV s USB port Before connecting your device to the TV please back up your files to prevent them from damage or loss of data SAMSUNG is not responsible for any data file damage or data loss Connect a USB HDD to the dedicated port USB HDD port Do not disconnect the USB device while it is loading The higher the resolution of the image the longer it takes to display on the screen The maximum supported JPEG resolution is 15360X8640 pixels For unsupported or corrupted files the Not Supported File Format message is displayed If the files are sorted by Basic View up to 1000 files can be displayed in each folder e MP3 files with DRM that have been downloaded from a non free site cannot be played Digital Rights Management DRM is a technology that supports the creation of content the distribution and management of the content in an integrated and comprehensive way including the protection of the righ
63. they cannot be workable at this moment Although this TV set meets the latest DVB T and DVB C standards as of August 2008 the compatibility with future DVB T digital terrestrial and DVB C digital cable broadcasts cannot be guaranteed Depending on the countries areas where this TV set is used some cable TV providers may charge an additional fee for such a service and you may be required to agree to terms and conditions of their business Some Digital TV functions might be unavailable in some countries or regions and DVB C might not work correctly with some cable service providers For more information please contact your local Samsung customer care centre The reception quality of TV may be affected due to differences in broadcasting method between the countries Please check the TV performance in he local SAMSUNG Authorized Dealer or the Samsung Call Centre whether it can be improved by reconfiguring TV setting or not Still image warning Avoid displaying still images like jpeg picture files or still image element like TV programme logo panorama or 4 3 image format stock or news bar at screen bottom etc on the screen Constant displaying of still picture can cause ghosting of LCD screen which will affect image quality To reduce risk of this effect please follow below recommendations e Avoid displaying the same TV channel for long periods e Always try do display any image on full screen use TV set picture format menu for best possib
64. tions e Anynet works when the AV device supporting Anynet is in the standby or on status e Anynet supports up to 12 AV devices in total Note that you can connect up to 3 devices of the same type Anynet Menu The Anynet menu changes depending on the type and status of the Anynet devices connected to the TV Anynet Menu Description View TV Changes Anynet mode to TV broadcast mode Device List Shows the Anynet device list Recording recorder Starts recording immediately using the recorder This is only available for devices that support the recording function device_name MENU Shows the connected device menus E g If a DVD recorder is connected the disc menu of the DVD recorder will appear device_name INFO Shows the play menu of the connected device E g If a DVD recorder is connected the play menu of the DVD recorder will appear Stop Recording recorder Stops recording Receiver Sound is played through the receiver If more than one recording device is connected they are displayed as recorder and if only one recording device is connected it will be represented as device_name English 29 Advanced Features D Setting Up Anynet E Setup Anynet HDMI CEC Off On To use the Anynet Function Anynet HDMI CEC must be set to On Q When the Anynet HDMI CEC function is disabled all the Anynet related operations are deactivated Auto Turn Off No Yes Setting a
65. title Language Primary Teletext Language Secondary Teletext Language Select a language which will be the default language when a channel is selected Subtitle Use this menu to set the Subtitle mode amp The subtitle feature does not work in Component or HDMI modes Subtitle Off On Switches subtitles on or off Mode Normal Hearing Impaired Sets the subtitle mode Subtitle Language Sets the subtitle language Ifthe programme you are watching does not support the Hearing Impaired function Normal automatically activates even if the Hearing Impaired mode is selected amp English is the default in cases where the selected language is unavailable in the broadcast Digital Text Disable Enable If the programme broadcasts with digital text this feature is enabled MHEG Multimedia and Hypermedia Information Coding Experts Group An International standard for data encoding systems used in multimedia and hypermedia This is at a higher level than the MPEG system which includes data linking hypermedia such as still images character service animation graphic and video files as well as multimedia data MHEG is user runtime interaction technology and is being applied to various fields including VOD Video On Demand ITV Interactive TV EC Electronic Commerce tele education tele conferencing digital libraries and network games General Game Mode Off On When connecting to a
66. tle Formats Name File extension Format MPEG 4 time based text ttxt XML SAMI smi HTML SubRip Srt string based SubViewer sub string based Wp suv Pause lt gt Jump 42 Tools 5 Return Micro DVD sub or txt string based 24 English Supported Video Formats File Extention Container Video Codec Resolution Femo wie inget Audio Codec fps Mbsp Divx 3 11 4 x 5 1 6 0 920x1080 6 30 8 avi AVI XviD 920x1080 6 30 8 MP3 AC3 LPCM mkv MKV H 264 BP MP HP 920x1080 6 30 25 ADPCM DTS HD MPEG4 SP ASP 920x1080 6 30 8 Divx 3 11 4 x 5 1 6 0 920x1080 6 30 8 XviD 920x1080 6 30 8 MP3 AC3 LPCM a i H 264 BP MP HP 920x1080 6 30 25 ADPCM WMA MPEG4 SP ASP 920x1080 6 30 8 wmv ASF Window Media Video v9 920x1080 6 30 25 WMA H 264 BP MP HP 920x1080 6 30 25 mp4 MP4 MPEG4 SP ASP 920x1080 6 30 8 MP3 ADPCM AAC XVID 920x1080 6 30 8 3gp 3GPP AOTER ME ME _ 2 ADPCM AAC HE AAC MPEG4 SP ASP 920x1080 6 30 8 a VRO MPEG1 920x1080 24 25 30 30 ENN VOB MPEG2 920x1080 24 25 30 30 MPEG1 920x1080 24 25 30 30 ka PS MPEG2 920x1080 24 25 30 30 AC3 MPEG LPCM AAC H 264 920x1080 6 30 25 die MPEG2 920x1080 24 25 30 30 RETRETIN TS H 264 920x1080 6 30 25 uae VC1 920x1080 6 30 25 Other Restrictions amp NOTE e If there are p
67. ts and interests of the content providers the prevention of the illegal copying of contents as well as managing billings and settlements If more than 2 PTP devices are connected you can only use one at a time If more than two MSC devices are connected some of them may not be recognized A USB device that requires high power more than 500mA or 5V may not be supported e If an over power warning message is displayed while you are connecting or using a USB device the device may not be recognized or may malfunction Ifthe TV has been no input during time set in Auto Protection Time the Screensaver will run e Ifa USB extension cable is used the USB device may not be recognized or the files on the device may not be read e Ifa USB device connected to the TV is not recognized the list of files on the device is corrupted or a file in the list is not played connect the USB device to the PC format the device and check the connection If a file deleted from the PC is still found when Media Play is run use the Empty the Recycle Bin function on the PC to permanently delete the file English 23 sounjes4j psdueApy 0 Advanced Features D Screen Display Move to the desired file using the up down right left buttons and then press the ENTER C or gt Play button The file is played Q amp Q Supports the Device Mode and Contents Mode in Media Play homepage Information i ES Videos movie o1 avi You can asce
68. tting the Clock Set the Clock Mode automatically or manually Mode Press the A or Y button to select Auto then press the ENTER C button 7 Viewing the HD The connection method for the best HD screen quality is displayed Connection Guide 8 Enjoy your TV Press the ENTER C button If You Want to Reset This Feature Select Setup Plug amp Play Initial Setup Enter your 4 digit PIN number The default PIN number is 0 0 0 0 If you want to change the PIN number use the Change PIN function 6 English Connections Connecting to an AV Device Using an HDMI DVI Cable HD connection up to 1080p Available devices DVD Blu ray player HD cable box HD STB Set Top Box satellite receiver cable box satellite receiver STB suondeuu0D Z0 J ra i i HDMI OUT cs 26 AUDIO OUT f AUBIOIN DVI OUT HDMI DVI IN 1 2 3 PC DVI AUDIO IN e When using an HDMI DVI cable connection you must use the HDMI DVI IN 1 jack For the DVI cable connection use a DVI to HDMI cable or DVI HDMI DVI to HDMI adapter for video connection and the PC DVI AUDIO IN jacks for audio e If an external device such as a DVD Blu ray player cable box STB satellite receiver supporting a HDMI versions older than 1 3 is connected the TV may operate abnormally e g no screen display no sound annoying flicker abnormal colour e If there is no sound after connecti
69. ty there might be regulations that require you to dispose of these batteries properly under environmental considerations Please contact your local authorities for disposal or recycling information Do not overload wall outlets extension cords or adaptors beyond their capacity since this can result in fire or electric shock e Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plug end adaptors and the point where they exit from the appliance To protect this apparatus from a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the antenna or cable system This will prevent damage to the set due to lightning and power line surges Before connecting the AC power cord to the DC adaptor outlet make sure the voltage designation of the DC adaptor corresponds to the local electrical supply e Never insert anything metallic into the open parts of this apparatus Doing so many create a danger of electric shock To avoid electric shock never touch the inside of this apparatus Only a qualified technician should open this apparatus e Make sure to plug the power cord in until it is firmly inserted When removing the power cord make sure to hold the power plug when pulling the plug from the outlet Do not touch the power cord with wet hands If this apparat
70. ur problems or a blank screen There is poor colour or brightness There is a dotted line on the edge of the screen e Adjust the Picture options in the TV menu go to Picture mode Colour Brightness Sharpness e Adjust Energy Saving option in the TV menu go to MENU Picture ECO solution Energy Saving P 14 e Try resetting the picture to view the default picture settings go to MENU Picture Picture Reset e Ifthe picture size is set to Screen Fit change it to 16 9 P 15 e Change cable set top box resolution The picture is black and white e If you are using an AV composite input connect the video cable yellow to the Green jack of component input 1 on the TV When changing channels the picture freezes or is distorted or delayed e If connected with a cable box please try to reset the cable box Reconnect the AC cord and wait until the cable box reboots It may take up to 20 minutes e Set the output resolution of the cable box to 1080i or 720p Sound Quality First of all please perform the Sound Test to confirm that your TV audio is properly operating go to MENU Support Self Diagnosis Sound Test P 20 If the audio is OK the sound problem may caused by the source or signal There is no sound or the sound is too low at maximum volume e Please check the volume the of external device connected to your TV The picture is good but there is no sound e Set t
71. us does not operate normally in particular if there are any unusual sounds or smells coming from it unplug it immediately and contact an authorized dealer or service center Be sure to pull the power plug out of the outlet if the TV is to remain unused or if you are to leave the house for an extended period of time especially when children elderly or disabled people will be left alone in the house Accumulated dust can cause an electric shock an electric leakage or a fire by causing the power cord to generate sparks and heat or the insulation to deteriorate e Be sure to contact an authorized service center when installing your set in a location with heavy dust high or low temperatures high humidity chemical substances and where it operates for 24 hours such as the airport the train station etc Failure to do so may cause serious damage to your set Use only a properly grounded plug and receptacle An improper ground may cause electric shock or equipment damage Class Equipment only e To disconnect the apparatus from the mains the plug must be pulled out from the mains socket therefore the mains plug shall be readily operable Do not allow children to hang onto the product Store the accessories battery etc in a location safely out of the reach of children e Do not install the product in an unstable location such as a shaky self a slanted floor or a location exposed to vibration Do not drop or impart any shoc
72. y 75X75 dias 100 X 100 M4 23 29 200 X 100 30 40 200 X 200 M6 aoa 46 55 400 X 400 E 57 65 600 X 400 M8 70 80 800 X 400 80 1400 X 800 A Do not install your Wall Mount Kit while your TV is turned on It may result in personal injury due to electric shock English 33 Other Information Anti Theft Kensington Lock The Kensington Lock is a device used to physically fix the system when using it in a public place The appearance and locking method N KA may differ from the illustration depending on the manufacturer Refer to a 1 0 the manual provided with the Kensington Lock for proper use 4 amp Please find a A icon on the rear of the TV f A kensington slot is beside the fa icon R 1 Insert the locking device into the Kensington slot on the LCD TV Y _9 3 and turn it in the locking direction w p 2 Connect the Kensington Lock cable lt Optional gt 3 Fix the Kensington Lock to a desk or a heavy stationary object The locking device has to be purchased separately amp The location of the Kensington Lock may be different depending on its model Securing the TV to the Wall children do not hang over or destabilize the TV doing so may cause the TV to tip over resulting in serious injuries or death Follow all safety precautions provided on the included Safety Flyer For added stability install the anti fall device for safety purposes as follows A C
73. y selected channel press the ENTER C button abel 18 11 Thu 6 Jan DTV Ak Life On Venus Avenue 1800 6 00 mammum Unclassified G Watch No Detaild Information B Information Planning Your Viewing Guide The EPG Electronic Programme Guide information is provided by broadcasters Using programme schedules provided by broadcasters you can specify programmes you want to watch in advance so that the channel automatically changes to the selected programme channel at the specified time Programme entries may appear blank or out of date depending on a channel status GUIDE Using Channel View DTV Air 800 five Home and Away 18 00 18 30 Drama Dani is devastated when scott makes clear his views on marriage 19 00 20 00 Tine Team Today 18 00 19 00 a 27 Discovery American Chopper 28 DiscoveryH amp L Programmes resume at 06 00 800 five Home and Family Affairs Fiv Dark Angel 24 price drop tv No Information 16 avc QVC Selection v6 R4DTT No Information w View Mode 24 Hours DI Ch Mode Information Page C Watch 10 English Using Scheduled View DTV Air 800 five Family Affairs 18 00 18 30 Drama Tanya confesses all to a stunned Babs Conrad is anxious to hear 18 30 Today 19 15 Today Family Affairs Dark Angel i View Mode Information C4 Cancel O Red View Mode View the list of programmes that are
74. you are currently watching If you are watching video from another device the video from the device is recorded Before recording check whether the antenna jack is properly connected to the recording device To properly connect an antenna to a recording device refer to the recording device s users manual 30 English D Listening through a Receiver You can listen to sound through a receiver i e Home Theatre instead of the TV speaker 1 Select Receiver and set to On 2 Press the EXIT button to exit A if your receiver supports audio only it may not appear in the device list amp amp The receiver will work when you have properly connected the optical in jack of the receiver to the DIGITAL AUDIO OUT OPTICAL jack of the TV amp when the receiver iie Home Theatre is set to On you can hear sound output from the TV s Optical jack When the TV is displaying a DTV aerial signal the TV will send out 5 1 channel sound to the receiver When the source is a digital component such as a DVD and is connected to the TV via HDMI only 2 channel sound will be heard from the receiver amp NOTE e You can only control Anynet devices using the TV remote control not the buttons on the TV The TV remote control may not work under certain conditions If this occurs reselect the Anynet device The Anynet functions do not operate with other manufacturers products ij Troubleshooting for Anynet sounjes4j psdueApy 0

Samsung LE-26C450E1WXZG 26" Full HD Black LCD TV

Contents

Download Pdf Manuals

Related Search

Related Contents

Samsung LE-26C450E1WXZG 26&quot; Full HD Black LCD TV

Contents

Download Pdf Manuals

Related Search

Related Contents

Samsung LE-26C450E1WXZG 26" Full HD Black LCD TV