Premier P2642F flat panel wall mount
Contents
1. IMPROPER INSTALLATION MODIFICATION USE OR MISUSE OF ITS PRODUCTS PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FORA PARTICULAR PURPOSE PREMIER MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE PRODUCTS OR PARTS SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU What Customers Must Do for Limited Warranty Service If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to the address below within thirty 30 days Proof of purchase an original sales receipt from the original consumer purchaser must accompany all warranty claims Warranty claims must also include a description of the problem the purchaser s name address and telephone number General inquiries can be addressed to Premier Mounts Customer Service at 1 800 368 9700 Warranty claims will not be accepted over the phone or by fax Premier Mounts Attn Warranty Claim 3130 East Miraloma Ave Anaheim CA 92806 How State Law Applies THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE Premier Mounts intends to make this manual accurate and complete However Premier Mounts m2. must be stacked and oriented as shown The Universal Spacers must only be installed between the mounting bracket and your flat panel The Universal Spacers will fit M4 M5 M6 and M8 screw sizes Proceed to the Locking and Leveling Screw Installation section POCOBCCEG Page 12 Visit the Premier Mounts website at http www premiermounts com Installation Instructions P2642F 22 Installing the Mounting Bracket contd Locking and Leveling Screw Installation Leveling Screw Installation You must install the leveling screws before you attach the mounting bracket to the back of the flat panel The leveling screws consists of two 2 M6 x 75mm screws Thread one 1 leveling screw into the top mounting hole on each of the mounting brackets Make sure the leveling screw is securely threaded into the mounting Leveling Screw tab before proceeding Correctly Threaded Do not thread the leveling screw any further once it is even with the mounting tab Threading the leveling screw any further will prevent you from Leveling Screw safely attaching the flat panel to the wall plate Threaded Too Far Locking Screw Installation You must install the locking screws before you attach the mounting bracket to the back of the flat panel The locking screws consists of two 2 M6 x 75mm screws Thread one 1 locking screw into the bottom mounting hole on eac
3. DO SO COULD RESULT IN PROPERTY DAMAGE SERIOUS PERSONAL INJURY OR EVEN DEATH SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT USE STOP PROPER SAFETY EQUIPMENT AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS AND IS NOT RESPONSIBLE FOR ANY DAMAGES CLAIMS DEMANDS SUITS ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM ARISING OUT OF OR INANY MANNER RELATING TO ANY SUCH USE ATTACHMENTS OR MODIFICATIONS At least two qualified people should perform the assembly procedure Personal injury and or property damage can result from dropping or mishandling the flat panel If mounting to wall studs or ceiling studs make sure that the mounting screws are anchored into the center of the wall studs or ceiling studs Use of an edge to edge stud finder is recommended A It is recommended that a maximum of plaster board be used when mounting to wooden studs Be aware of the mounting environment If drilling and or cutting into the mounting surface always make sure that there are no electrical wires in wall Cutting or drilling into an electrical line may cause serious personal injury Make sure there are no water or natural gas lines inside the wall where the mount is to be loca
4. Padlock Place the locking hook through the hole of the security barrel Snap lock and locking hook together PCB CSL1 Padlock Combination or Keyed Technical Specifications All measurements are in inches millimeters 16 50 15 87 419 403 Page 16 Visit the Premier Mounts website at http www premiermounts com Installation Instructions gt 4 P2642F PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product The limited warranty is valid only for the original purchaser of the product What Premier Mounts Will Do At the sole option of Premier Mounts Premier Mounts will repair or replace any product or product part that is defective If Premier Mounts chooses to replace a defective product or part a replacement product or part will be shipped to you at no charge but you must pay any labor costs What is Not Covered Limitations PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS ADAPTERS DISPLAYS PROJECTORS OTHER PROPERTY OR PERSONAL INJURY RESULTING IN WHOLE OR IN PART FROM
5. akes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Premier Mounts makes no representation of warranty expressed or implied regarding the information contained herein Premier Mounts assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Premier Mounts 2010 Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 17
6. cD PREMIER Cad MOUNTS CREATING POSITIVE CUSTOMER EXPERIENCES INSTALLATION INSTRUCTIONS A Vr E Y RR NS N Q gt ee Si CCCOCOCCOCCCOOCEGEGEGE pe f LL 7 OCCBOCCCOOCGCEBCCGEEGE Universal Low Profile Flat Mount for 26 to 42 Flat Panels Model P2642F NORTH AMERICA EUROPE AUSTRALIA AND OCEANIA 3130 East Miraloma Avenue Swallow House Distributed by Amber Technology Limited Anaheim CA 92806 USA Shilton Industrial Estate Unit B 5 Skyline Place USA and Canada Shilton Coventry England CV79JY Frenchs Forest NSW 2086 Phone 1 800 368 9700 Phone 44 0 2476 614700 Australia Fax 1 800 832 4888 Fax 44 0 2476 614710 Phone 61 2 9452 8600 Sydney Office Other Locations Toll Free 1 800 368 9700 Phone 001 714 632 7100 Email mounts ambertech com au Fax 001 714 632 1044 9531 202 A01 02 z P2642F Weight LMR ces wate eects tee tetas nec tees van atecqeeeelacec ee ta teaaatt Sot cngateceeten ateecu a tseetatge ttneteaastiueeteeaat 2 Warning Statements 3 ss scsccstssasceciten r aa EEEE EEEN E EEE EA EE E E EEE EE OAE AE Eaa OERS 2 installati n TOOMSs cy ke aa e e Eae Ea a A Ee a a aa e E EEEE ETE eE Ar a AEE aa aas ae E 3 Parts List psen este cease nus nnes na aap ansaan eNEAN EEEE A es AAEE EAEAN EEE EE CAAO ea shaogo ier Eee dah EAN EAE Ep ANRE EAA EEEa 3 Mounting HardWare ss set cansessesteeses atse
7. cation on the wall where you will be mounting your flat panel Use a stud finder to determine the exact center of each steel stud in the vicinity of the mounting location Use a pencil and mark the exact center of each steel stud Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 9 b a 24 P2642F Installing the Wall Plate cont d Place the wall plate against the wall in the desired viewing location Adjust the wall plate to match the locations of the steel studs Level the wall plate Use a pencil and mark 2 upper and 2 lower locations where you will be drilling holes for the steel stud anchors Set the wall plate to one side in a safe location Use a power drill and 74 drill bit to drill a hole at each of the marks Insert a steel stud anchor into each hole If necessary lightly tap each steel stud anchor into place with a hammer stud anchor screw until the legs have completely A compressed against the back of the steel stud The steel stud anchor screw will feel tight when w oee CTY MMM eez p ESS A Use a Phillips screwdriver to tighten each steel you first begin to turn it until the legs begin to compress The steel stud anchor screw will then turn easier for several turns The steel stud anchor screw will again feel tight when the legs have completely compressed against the back of the drywall Stop turning the steel st
8. cking Safety Screws Prevents the flat panel from being removed or dislodged from the wall plate Universal Spacers Premier Mount s uniquely Leveling Screws Allows for leveling adjustments of the flat panel after mounting Cable Electrical Cut Out A large cut out on the wall plate allows for easy cable access and power distribution installations Directional Mounting Arrow Directional Mounting Arrow lets you know which edge is up Low Profile Design Holds the flat panel less than 1 from the wall SS N POCOCCEGBOCCEGE E S BE designed spacers that fit multiple screw sizes Visit the Premier Mounts website at http www premiermounts com Page 5 b a 24 P2642F Installing the Wall Plate Introduction itt Directional Mounting Arrow The Directional Mounting Arrow stamped into the top of the P2642F wall mount indicates which edge is the top Mounting Safety Two people are recommended to for the installation of this mount 0000000000 0 5000000000000000 gt Cc Cop Determining the Mounting Surface If you will be installing your P2642F mount to wood studs proceed to the Wood Stud Installation section If you will be installing your P2642F mount to a concrete wall proceed to the Concrete Installation section If you wi
9. ee eneee eE E EE EA EE EE E EEA Ea SEOANE aR E EA R ENNES 4 FAWN OS 5 cas sete E E A AE E E T E E E E E E E A E E ceeeacaastenepeneees 5 Installing the Wall Plate eanes eneee eE eenaa anaes EE aee E EEES EA aa Ee EEEE EAE EEES NAA NE ENE EE EEE ER 6 VAT OGU CU OM E EEE E E E A E E E E A T A T 6 Determining the Mo nting Surfa Esseri aa tanstans aa a snaked eieaa aitaa aeaa aa Eaei eieaa Seodra 6 Wood Stud Installation aie aries r a Shc a e ee a aa e aaa E A NET 6 Concrete llnstalation ssec ae eni e n ase E A En aA Eate S Ea EAEE 8 Steel St d Installation ieia no iai anae enian Ean aaa EEAS AE AANE O Ea EEN EEE E EAE EEUE AES ENEE EERE 9 Installing the Mounting Bracket s2 4 asce0ds sees ih ene e ene OEE AEE E EAEE eE eT EEEE ESE EAEE NEE EEEE 11 Selecting the Mounting HardWare ic cccccscicccoscescesccestenedseced aea es iare aai a eae ar a iaee riea ae retroe eerie odeti 11 Universal Washer Installation sesiccse scsssecsssseecnnessceescencetsn opens deeeeeauns cnn ccechusstneseehan aAA taad irae EAN aaia EKE Aiden estes 12 Universal Spacer Installation ccccccccccccccceceeceeeeeseseeeeeeeaeeeeeeeeeeeeeeeeeeeeeeseesescseeceeeseeeaeaeaeaeeeeeesaseseeeeeeeeeeseeeseseeeeeneeaeaes 12 Locking and Leveling Screw Installation esinen eeni e ei EE EEE eT EA e aE renea a aeaa 13 Lock lt Security Barrel Installation Optional resena aes see caveeeits cavea stags ac seseciecieescesaieieesvesciebosteascieiteesaseaiteacasteccieiiees
10. er and 2 lower mounting locations where you will be drilling holes for the concrete wedge anchors Each horizontal location cannot be closer than 12 apart Set the wall plate to one side in a safe location Use a power drill and 5 4 masonry drill bit to drill a hole at each of the marks Page 8 Visit the Premier Mounts website at http www premiermounts com Installation Instructions gt 4 P2642F 22 Installing the Wall Plate cont d Insert a concrete wedge anchor into each hole If necessary lightly tap each concrete wedge anchor into place with a hammer Remove the nuts and washers from all four 4 concrete wedge anchors Replace the washers which you removed from the concrete wedge anchors with the 4 washers shown in the parts list on Page 3 Place the wall plate against the wall over the threaded shafts of the concrete wedge anchors Attach the nuts and 4 washers to each of the concrete wedge anchors and tighten using a socket wrench and an M10 socket Do not overtighten the wedge anchor nuts Proceed to the Installing the Mounting Bracket section Steel Stud Installation The supplied M6 steel stud anchors must be used to install your Premier Mounts mount to steel studs Do not use lag bolts or wood screws Steel Stud Anchor Screw Steel Stud Anchor Sleeve NNN Identify the general lo
11. h of the mounting brackets Make sure the locking screw is securely threaded into the mounting tab before proceeding Do not thread the locking screw any further once it is even with the mounting tab Threading the locking screw any further will prevent you from safely attaching the flat panel to the wall plate Locking Screw Correctly Threaded Proceed to the Lock It Security Barrel Installation section Locking Screw Threaded Too Far Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 13 gt 4 24 P2642F Lock It Security Barrel Installation Optional li Optional security configurations include PCB CSL1 sold separateh Padlock Combination or Keyed commercially available Mounting Tab Please read the following directions to install the security barrel Remove the locking screw from the mounting bracket Place the locking screw into and through the security barrel see illustration below Re insert the locking screw and security barrel into the mounting bracket Tighten the locking screw and security barrel until seated in the mounting tab Do not thread the locking screw any further once it is even with the mounting tab see illustration to the right Threading the locking screw any further will prevent you from safely attaching the flat panel to the wall plate 1 D
12. ided Threaded Insert The correct screws should thread easily into the Thread Depth Indicator mount point and not pull out when tension is C Figurei applied Proceed to the Universal Washer Installation section Small Straw or Toothpick Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 11 b a eZ P2642F Installing the Mounting Bracket contd Universal Washer Installation Premier Mounts Universal Washers are designed to accommodate the various M4 M5 M6 and M8 hole sizes required by flat panels Do not place excessive pressure on the back of the flat panel as this may damage your flat panel The Universal Washer must be installed between the head of the mounting screw and the mounting bracket as shown Does your flat panel have Recessed mount points Uneven mount points Acurved back Any obstruction near the mount point If Yes you must install Universal Spacers Proceed to the Universal Spacer Installation section Mounting Screw If No skip to the Locking and Leveling Screw Universal Washer Installation section Mounting Bracket Universal Spacer Installation Premier Mounts Universal Spacers allow you to attach the mounting bracket to flat panels which have recessed or uneven mount points Each Universal Spacer adds to the distance between the mounting bracket and your flat panel The Universal Spacers
13. l Low Profile Flat Mount Assembly Components CC C CCCCCECECECCCEOE CCCBOOCCOOCCCOOCOCOCS Mounting Brackets Qty 2 Wall Plate Qty 1 M6 x 75mm Screws Qty 4 5 16 Flat Washers Universal Spacers Security Barrel Qty 6 Qty 1 Pro Mounting Hardware M6 Steel Stud Anchors Qty 6 5 16 Concrete Wedge Anchors Qty 6 5 16 x 3 Lag Bolts Qty 6 Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 3 b a 24 P2642F Parts List con d Page 4 M4 x 16mm Screw Qty 6 M4 x 25mm Screw Qty 6 M4 x 30mm Screw Qty 6 M5 x 16mm Screw Qty 6 M5 x 25mm Screw Qty 6 M5 x 30mm Screw Qty 6 M6 x 16mm Screw Qty 6 M6 x 25mm Screw Qty 6 M6 x 30mm Screw Qty 6 M6 x 45mm Screw Qty 6 Mounting Hardware M8 x 16mm Screw Qty 6 M8 x 25mm Screw Qty 6 M8 x 30mm Screw Qty 6 M8 x 45mm Screw Qty 6 M8 x 70mm Screw Qty 4 Visit the Premier Mounts website at http www premiermounts com Installation Instructions P2642F pdocoeococcocece e Installation Instructions EUN NRAN S Poe ea Allow for a variety of stud configurations and lateral shift adjustments when mounting your flat panel Lo
14. ll be installing your P2642F mount to a steel frame proceed to the Steel Stud Installation section Wood Stud Installation You must secure the wall plate to two 2 wall studs with a minimum of four 4 lag bolts 2 lag bolts for each stud found Use a stud finder to determine the exact center of wall studs in the vicinity of the wall plate Use a pencil to mark the exact center of each of the wall studs Two people are recommended for this step one person to level the wall plate and another person to mark the wall stud location Place the wall plate against the wall in the desired viewing location Adjust the wall plate to align the mount slots in the wall plate with the center of the wall studs Level the wall plate Use a pencil to mark the upper right mounting location along the center of the wall stud Page 6 Visit the Premier Mounts website at http www premiermounts com Installation Instructions gt 4 P2642F D2 Installing the Wall Plate contd Drill a pilot hole in the center of the upper right mark using a 4 drill bit and power drill A Only use a 4 drill bit when drilling the pilot holes Place the wall plate against the wall and align it with the pilot hole Insert one 1 5 4 x 3 lag bolt and one 1 5h washer into the upper right mounting hole and tighten using a socket wrench and 7 socket A Do not overtighten the lag bolt Level the wall plate U
15. ly keeping it close to the wall Engage the top and bottom mounting brackets to the rails of the wall plate Proceed to the Mounting Bracket Adjustments section Mounting Bracket Adjustments Leveling Screw Adjustment If your flat panel is tilted too far to one side the leveling screws will allow you compensate for this tilt by simply adjusting the screws with a screwdriver Loosen both locking screws Adjust the tilt of your flat panel Tighten both locking screws M6 x 75mm Leveling Screw 1 per Bracket Caution It is possible to dislodge your flat panel while you level your flat panel Use extreme caution until you tighten the locking screws Locking Screw Adjustment After you have finished leveling your flat panel be sure to tighten the two 2 M6 x 75mm locking screws A Do not overtighten the locking screws M6 x 75mm Locking Screw 1 per Bracket Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 15 b a 24 P2642F Utilizing the Security Barrel a Your P2642F Mount includes one 1 Security Barrel which can provide additional theft deterrence for your flat panel PCB CSL1 Security Cable _ Thread the cable through the hole on the security barrel Attach the PCB CSL1 locking mechansim and secure it using the supplied key
16. o not overtighten the locking screw Proceed to the Attaching the Mounting Bracket to the Flat Panel section Locking Screw Lock It Security Barrel Attaching the Mounting Bracket to the Flat Panel This section presumes that you have read and understood these sections Selecting the Proper Mounting Hardware Universal Washer Installation Universal Spacer Installation Place your flat panel screen side down on a soft flat surface O Identify the number and location of the thread inserts on the back of your flat panel Aligning the holes on each mounting bracket with the thread inserts on the back of your flat panel Secure each mounting bracket to your flat panel by inserting a minimum of two 2 screws per bracket A Do not overtighten the mounting hardware Proceed to the Attaching the Flat Panel to the Wall Plate section Page 14 Visit the Premier Mounts website at http www premiermounts com Installation Instructions P2642F D2 Installing the Mounting Bracket contd Attaching the Flat Panel to the Wall Plate A This section requires two people Do not fele ase your flat panel until you are certain that top and bottom hooks of both mounting brackets are securely seated on the upper and lower mounting rails of the wall panel Raise the flat panel past the top and bottom mounting rails on the wall panel Slide the flat panel down slow
17. s 14 Attaching the Mounting Bracket to the Flat Panel ccccccceceececeeceeeeeeeeeceeeeeeeaeeaeeeeceeeaeceeeescaaeeeeeeeeceaeeeeseseaeeeeees 14 Attaching the Flat Panel to the Wall Plate 0cccccceccceeeeeeceeeeceeenaececeeeaaeeeeeeceaaeaeeeesaeeaaecesegesaaaeeeeeeseaaeaeeeeeneneaeeeeees 15 Mounting Bracket Adjustments saves scccctess es eoue EE EE NT EEr EA Eae E A A E EAN EA EAER LEENE 15 Leveling Sew AG USUM GIs asine eaae a a Aa Rea E E E E a EE Ei 15 LOCKING Screw AGJUSUMEM rrisnin neeaaea aaee eA Eea E aea E aE e Eae ETA NE E EEEE E aE Eiana EEEN 15 Utilizing the Securty Barelo ieira nipe eroa E Ee Edea deea eae E eE a ad oeae aaa DR e aaeeea aeS 16 Technical Specifications sinisisi eiiis ie eia i eieiei aidaa iniiae jeden Eae ei E ieina rE iS aiiai 16 KAE EENI a A E E eatin E A a aiden ve E E E A E E Aaa Geo aan naa ns 17 De e E T A E adel E E T E E A E 17 Weight Limit THE WALL STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST FIVE TIMES THE WEIGHT OF NEATE A Peniel Weight 1 3 0 bs THE FLAT PANEL IF NOT THE WALL STRUCTURE MUST BE REINFORCED Warning Statements PRIOR TO THE INSTALLATION OF THIS PRODUCT THE INSTALLATION INSTRUCTIONS MUST BE READ AND COMPLETELY UNDERSTOOD KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN MUST BE FOLLOWED AS OUTLINED STOP IN THESE INSTALLATION INSTRUCTIONS FAILURE TO
18. se a pencil to mark the remaining three 3 mounting locations along the center of each wall stud Two people are recommended for this step one person to level the wall plate and another person to drill the pilot holes Drill a pilot hole in the center of each of the marks with a power drill and a 1 4 drill bit A Only use 4 drill bit when drilling the pilot holes Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 7 b a eZ P2642F Installing the Wall Plate cont d Insert one 1 54 x 3 lag bolt and one 1 h washer into each pilot hole Tighten all lag bolts using a socket wrench and 14 socket Do not overtighten the lag bolts when attaching the mount to the wall Improper installation may result in personal injury or property damage Proceed to the Installing the Mounting Bracket section Concrete Installation The supplied 5 6 concrete wedge anchors must be used for concrete installation You will need a 46 concrete drill bit which is available at your closest hardware store Concrete Wedge Anchors Example of 6 Concrete Drill Bit Not Included Two people are recommended for this step one person to level the wall plate and another person to mark the mounting locations Place the wall plate against the wall in the desired viewing location Level the wall plate Use a pencil and mark 2 upp
19. ted Cutting or drilling into a water or gas line may cause severe property damage or personal injury This product is intended for indoor use only Use of this product outdoors could lead to product failure and or serious personal injury Do not install near sources of high heat Do not install on a structure that is prone to vibration movement or chance of impact Contact Premier Mounts with any questions 800 368 9700 techsupport mounts com Page 2 Visit the Premier Mounts website at http www premiermounts com Installation Instructions gt A P2642F e Installation Tools The following tools may be required dependent upon your particular installation These tools are not provided by Premier Mounts but you can purchase them at your local hardware store fs A v4 Drill Bit for 7 16 Drill Bit for Electronic Stud Finder Wood Stud Steel Stud 5 16 Concrete Drill Bit Hand Held Drill SS Tape Measure Hammer Protective Eyewear Socket Wrench Ya Socket M10 Socket Phillips Tip Screwdriver Optional tools for steel stud installations Optional tools for concrete installations Parts List Your Premier Mounts product is shipped with all proper installation hardware and components Make sure that none of these parts are missing and or damaged before beginning installation If there are parts missing and or damaged please stop the installation and contact Premier Mounts 800 368 9700 P2642F Universa
20. ud anchor screw at that point A Do not overtighten the steel stud anchor screw Remove the steel stud anchor screws and set them aside Aa Steel stud anchors may come with small paper washers You may leave them on the screw or discard them These small paper washers do not replace standard h washers Page 10 Visit the Premier Mounts website at http www premiermounts com Installation Instructions Align the wall plate over the steel stud anchor sleeves Insert a steel stud anchor screw and a 4s washer into each steel stud anchor sleeve Use a Phillips screwdriver and tighten each steel stud anchor screw until it is just snug A Do not overtighten the steel stud anchor screws Do not use a power drill to tighten the steel stud anchor screws Proceed to the Installing the Mounting Bracket section Insert the Thread Depth Indicator into the thread inserts found on the bottom or top of the flat panel Use a pencil to mark the depth of the thread insert on the Thread Depth Indicator as shown in Figure Insert the Thread Depth Indicator into the remaining thread inserts to compare and verify their depth Locate the correct diameter screw for the thread insert If the screw you selected is longer than the mark on the Thread Depth Indicator as shown in Figure 2 and Figure 3 do not use this screw The screw length must not bypass the mark Marking the Depth Test each size of the screws prov
Download Pdf Manuals
Related Search