Lenco TFT-725
Contents
1. allow you sort the channels by A lt gt Z or Pay lt gt Free Note This option will not appears in this list when SETUP gt Installation gt LCN is set to ON 2 3 1 6 Skip Skip will skip the program when changing program by CH Press lt OK gt button to set or clear skip status when Skip option selected 2 3 1 7 Delete Delete will delete the program permanently from database User must rescan to recover it Press lt OK GREEN gt button to set delete one or delete all when Delete option selected 2 3 1 8 SW Update Update software by USB Enter file browser and press lt Left Right OK gt button to change folder and focus on the update file press lt OK gt button to start update 2 3 1 9 Search User can search the program name by partial keyword 1 Press lt Left Right gt button to select Search option 2 Press lt OK gt button to entry search page 3 Press lt Up Down Left Right OK 0 9 RED GREEN gt button to input keyword 4 Press lt OK gt button to Search and return List The matched program will be focused 5 Press lt GREEN YELLOW gt button to the next or previous matched program 2 3 2 Guide Guide is also naming EPG Electronic Program Guide See Figure 8 1 Press lt Up Down gt button to select program or EPG event 2 Press lt Left Right gt button to change event or date 3 Press lt OK gt button to exit all the menus or show the detail information of selected event 4 Press lt Exit gt button to exit2. is not in use Attention should be drawn to the environmental aspects of battery disposal CAUTION Danger of explosion if battery is incorrectly replaced Replace only with the same or equivalent type WARNNING The battery battery or batteries or battery pack shall not be exposed to excessive heat such as sunshine fire or the like WARNNING Excessive sound pressure from earphones or headphones can cause hearing loss WARNNING Only use attachments accessories specified provided by the manufacturer the product is supplied by AC adapter the AC adapter is used as disconnect device the disconnect device shall remain readily operable Caution Danger of explosion if battery is incorrectly replaced replaced only with the same or equivalent type Lithium battery Important Safety Instructions For good reception place the rod antenna as near as the window of house and place it as far as the screen of this DVB T receiver Don t place the rod antenna near other machine appliance such as motor computer switching power TV audio power amplifier speakers etc since these machines appliances can cause interferences to the antenna Remote Control Remote Key Function 1 SOURCE To select input source 2 INFO 3 NUMBER KEYS Used to select channel numbers or input numbers in menus 4 5 TEXT Used to open teletext OSD display if teletext available in the broadcasted stream 6 SUBTITLE Used to switch betwee
3. to previous menu Figure 8 Guide Event 5 Press lt RED gt button to enter Book page and lt YELLOW gt button to save after edited If it conflict with itself or other event a conflict message will be displayed The successful booking will be added to Main Menu gt SETUP gt Advance Timer see section 2 2 4 2 4 MULTIMEDIA Multimedia must be used with external USB device inserted otherwise the Device is not ready message will be displayed remove device when playing photo or MP3 WMA the Device is removed message will be displayed and return to Main Menu 2 4 1 My Album My Album can display JPG BMP GIF photos and operate it If there are photos in device root folder it will start at Thumbnail mode otherwise it will start at Folder mode Press lt BLUE gt button can switch to Folder mode and lt Exit gt button to Thumbnail mode again 10 2 4 1 2 Zoom Press lt RED gt button to zoom in or zoom out the photo in view mode The zoom factor can be 25 50 100 150 2 00 If zoom factor greater than 100 press lt Up Down Left Right gt button can move around the photo 2 4 1 3 Rotation Press lt Left Right gt button to rotate left or right and lt YELLOW BLUE gt button to flip horizontal or vertical in view mode After rotating or flipping the photo and return Thumbnail mode the effect will be keeped 2 4 1 4 Slide Show Press lt OK gt button to view the photo from Thumbnail or Folder mode and press it again to st
4. K gt button to display Program List with No name and lock scramble skip status See Figure 13 Press lt Up Down Left Right gt to switch the program Press lt OK Exit gt to return normal play mode Figure 13 Program List Figure 14 Audio Channel 3 5 Audio Switch the sound channel and switch sound mode to LR stereo or LL left or RR right If setting audio language at SETUP gt Installation gt Audio Language the audio channel default language will be chosen by setting See Figure 14 Press lt Audio gt button to display the audio channel page Press lt Up Down gt button to select Channel Audio PID or Sound Mode option Press lt Left Right gt button to set the value 3 6 Pause Pause video and audio But it will be canceled by any input 3 8 Teletext Display teletext on screen the style of teletext may be different by content provider See Figure 15 Press lt Text gt button to display the teletext setting page Press lt Up Down gt button to select the teletext language if the program has teletext Press lt OK Exit gt button to exit the teletext setting page Press lt 0 9 Up Down Left Right gt button to change teletext page if teletext exists 13 3 9 Subtitle Display the subtitle on screen the style of subtitle may be different by content provider See Figure 16 Press lt Subtitle gt button to display subtitle setting page Press lt Up Down gt button to select subtitle language if the program has subtitle Pre
5. TFT 725 PORTABLE DIGITAL TV DVB T User Manual Size 120X170mm For information and support www lenco eu User interface Quick Installation Menu Operations Normal Play 3 5 2 6 6 7 12 14 14 14 Important Safety Instructions Remote Control Front and Rear panel illustration Screen Setting Support Specifications 1 Introduction 2 Warning To reduce the risk of electric shock do not remove the cover or back There are no user serviceable parts inside Refer servicing to qualified personnel Warning To prevent fire or electric shock hazard do not expose the unit to rain or moisture Do not expose the Adaptor and product to water dripping or splashing and no objects filled with liquids such as vases should be placed on the unit Keep the product away from direct sunlight and heat source such as radiators or stoves Do not block the ventilation openings Slots and openings on the unit are provided for ventilation The openings should never be blocked by placing your product on a cushion sofa or other similar surface Do not place the product on unstable cart stand tripod bracket or table The unit may fall resulting in possible damage or injury Never place heavy or sharp objects on the LCD panel or frame Only use the AC adapter included with product Using any other Adapter Will void your warranty Unplug the power from the outlet when the unit
6. and Radio are almost the same Herein take TV as example 2 3 1 List User can operate some functions in List See Figure 7 Figure 7 TV List 2 3 1 1 Favorites User can quickly channel up down the favorite programs by favorite filter There are 8 groups of favorite for user setting News Sport Movie Music Shopping Travel Boy and Girl Press lt 1 8 gt button to set or clear the favorite group when Favorites option selected 2 3 1 2 Lock Lock will ask password before watching this program when SETUP gt Password gt Channel Lock is turned on Please see section 2 2 3 2 for details Press lt OK gt button to set or clear lock status when Lock option selected 2 3 1 3 Edit User can edit the program name maximum length is 20 characters 1 Press lt Left Right gt button to select Edit option and lt Up Down gt button to select the program 2 Press lt OK gt button to display program info and press it again to edit program name 3 Press lt Up Down Left Right 0 9 RED GREEN gt button to select the character 4 Press lt OK gt button to finish the editing and return to previous program info page 5 Press lt RED gt button to save the editing and return to List or press lt Exit gt button to return to List without saving 2 3 1 4 Move Move will allow you move the position of the channels in the list Note This option will not appears in this list when SETUP gt Installation gt LCN is set to ON 2 3 1 5 Sort Sort will
7. art the slide show Press lt RED gt button to play or pause the slide show Press lt GREEN gt button to set music playing at background when slide show Press lt YELLOW gt button to set repeating or once Press lt BLUE gt button to set the time interval between current and next photo Press lt Up Down gt button to next or previous photo right away Figure 9 My Album Thumbnail 11 2 4 1 1 Thumbnail Folder The info Width X Height and Date of selected photo will be displayed at the left bottom in Thumbnail mode and right up in Folder mode See Figure 9 Press lt Up Down Left Right OK gt button to browse folders or files Press lt OK gt button to view the selected photo and press again to start slide show Press lt Info gt button to select device between USB and Card Reader or external USB hub 2 4 2 My Music My Music can play most of MP3 WMA files It displays progress bar audio spectrum current playing time and total time while playing See Figure 10 Press lt Info gt button to select device between USB and Card Reader or external USB hub Press lt Up Down Left Right OK gt button to browse folders and files Press lt OK gt button to start play Press lt RED gt button to play or pause Press lt GREEN gt button to stop Press lt YELLOW gt button to set play mode as Repeat All Repeating Random repeat Off Press lt BLUE gt button to set fast forward speed as x2 x3 x4 Normal Press lt Left Right Mute gt butt
8. he language for displaying subtitle 2 2 1 6 LCN Set the Logical Channel Number to on or off Note LCN is a number that uniquely identifies a logical channel which is popular in some european countries such as England France 2 2 1 7 Auto Time Zone Time Zone Allow you to enable or disable auto time zone offset update If you know the GMT Greenwich Mean Time time zone offset of your location set the Auto Time Zone to OFF and select an appropriate Time Zone otherwise set it to ON and let the system update the time zone automatically according to the transport stream See Figure 3 Note Some Countries are covered with more than one Time Zone 2 2 1 8 Auto Scan Press lt OK gt button to start Auto Scan See section 1 2 1 for details 2 2 1 9 Manual Scan Press lt GREEN gt button to start Manual Scan See section 1 2 2 for details 8 2 2 2 3 Banner Display Time Set Banner displays time Banner doesn t disappear when set as Always and disappears at timeout when set as other values 2 2 3 Password Set password for menu lock or channel lock or censorship lock And the user can change password here the default PIN Code is 6666 See Figure 6 Figure 5 TV Setup Figure 6 Password Page 2 2 3 1 Menu Lock Lock the menus by password 2 2 3 2 Channel Lock Lock the channel which has been set to lock status when turning on the Channel Lock Please see section 2 3 1 2 for details 2 2 3 3 Censorship Lock Lock the program by pas
9. ight Up Down gt to select different sub menu See Figure 1 3 Press lt OK gt button to enter the selected sub menu 4 Press lt Menu Exit gt to exit the current menu If there is no channel database in the STB it will show Installation menu directly when booting See Figure 2 You can press lt OK gt button to start Auto Scan or lt GREEN gt button to start Manual Scan 1 2 How to receive the programs Scan the possible frequency and bandwidth to receive the programs Press lt OK gt or lt GREEN gt button to start Auto Scan or Manual Scan 1 2 1 Auto Scan Auto Scan will erase the database first and scans default frequency and bandwidth by Country Setting Follow the steps 1 4 at section 1 1 Then Press lt OK gt button to confirm to clear the current database and start Auto Scan Figure 1 Main Menu SETUP Figure 2 SETUP Installation Figure 3 Clear database message It costs time to do Auto Scan user can press lt Exit gt button to exit at anytime See Figure 3 Later if you want to scan again you can follow above Quick Installation procedure Figure 4 Manual Scan edit 1 2 2 Manual Scan Manual Scan adds the scanning results into database it doesn t erase the database But the User has to know the Frequency and Bandwidth for scanning If the user scans the same Frequency and Bandwidth more than once the previous programs will be overwritten Follow the steps 1 4 at scetion 1 1 5 Press lt Up Down gt t
10. ilable for all channels 2 A V output is not available when the unit is working in AV in mode it only works in DTV mode 3 FUNCTION SCREEN SPEAKER ASPECT will act as RED GREEN YELLOW BLUE key when osd menu is on the screen MUTE INFO SOURCE AUDIO 0 7 8 9 4 5 6 1 2 3 TV RADIO PAUSE EPG SUBTITLE FAV MENU EXIT SETUP SPEAKER ASPECT CH CH OK RECALL TTX SCREEN VOL VOL 1 2 3 4 5 6 7 8 10 11 12 13 14 15 16 17 18 19 20 9 1 2 CR2025 HOW TO REPLACE THE BATTERY STEP 1 PUSH THE BUTTON TOWARD LEFT STEP 2 PULL THE BATTERY LOADER OUT Using the Remote Control Point the remote control at the remote sensor in order for the player to function correctly The remote will O function to approximately 21 from the remote sensor at an angle of approximately 30 each direction Note Directing the remote sensor toward any light source such as direct sunlight may cause the unit to malfunction Do not spill water or put wet items on the remote control Never disassemble remote control Caution Incorrect use of batteries may cause them to leak corrode or explode Be sure to place the batteries in the correct direction It is dangerous to charge heat open or short circuit the batteries Do not leave dead or expired batteries or mix old new batteries When not using the remote control for a long duration of time remove the batterie
11. m DC IN JACK This is used for AC DC adaptor input the voltage range is 12V CHARGE INDICATOR The system is in charging state when red LED is lighting it will turn into green when full charged 3 4 5 6 Panel illustration 5 13 16 14 15 16 17 1 SOURCE To select input source 2 SETUP Used to adjust the brightness contrast color hue parameter of TFT screen when there is no menu on the screen 3 CH Move around the menu screens or selecting the channels in non menu state 4 OK Confirm a selection within a menu 5 VOL Move around the menu screens or changing the volume in non menu state 6 VOL Move around the menu screens or changing the volume in non menu state 7 CH Move around the menu screens or selecting the channels in non menu state 8 ASPECT To change picture aspect 9 MENU Open the main menu window 10 EXIT Exit menu 11 REMOTE CONTROL SENSOR Receive the signal from the remote control 12 TFT screen Display the TFT widescreen display 13 Antenna input Connect to an external RF signal 14 Speaker Left The left speaker 17 Speaker Right The right speaker 15 USB mini plug 16 Memory Card slot 10 9 1 2 3 4 5 6 7 8 11 12 1 2 3 4 5 6 6 User Interface 1 Quick Installation 1 1 Setting Country and Language User can select preferred country and language at Setup Installation page 1 Press lt Menu gt button to enter Main Menu 2 Press lt Left R
12. mote control batteries exhausted Aerial may not be compatable Aerial is damaged misaligned What to do Check aerial lead Check aerial Check with dealer Press the DTV AV button Select an alternative channel Plug in and turn on set top box Aim remote control at front panel Check for obstructions Check batteries are inserted correctly Replace remote control batteries Check with dealer Check aerial Press the SCREEN button Press the SPEAKER button Support VHF 174MHZ 230MHZ UHF 470MHZ 862MHZ Color TFT LCD 7 inches 1Vp p 75 2CH DC IN 12V 15W 220X125X31 5MM Input Frequency Display Device Screen Size Screen pixels Video output Audio output Power Voltage Power consumption Size 480x234 px Specifications Press the FUNCTION button to display PICTURE setting as bellow Press lt Up Down gt button to select different option Press lt Left Right gt button to adjust different values of the selected option Press lt Exit gt button to exit the menu Note HUE option is only adjustable when input NTSC signal in DTV AV mode S color option will be available only in AV in mode BRIGHT 50 CONTRAST 50 COLOR 50 HUE 50 S COLOR AUTO LANG ENGLISH DEFAULT SELECT ADJUST ZOOM 16 9 PICTURE SCREEN SETTING Specifications are subject to change without notice
13. n different subtitles that are broadcasted 7 EXIT Used to return to the previous screen or menu 8 ASPECT Used to adjust aspect 16 9 or 4 3 of the screen when there is no menu on the screen 9 SPEAKER Used to close or open the speakers output when there is no menu on the screen 10 MUTE Used to turn the sound on or off 11 EPG 12 PAUSE Used to pause or playback the program being viewed 13 FAVORITE Used to access your favourite channels 14 TV RADIO Used to switch between TV channels and Radio stations 15 RECALL Used to switch between the last two viewed channels 16 CH Used to move around the menu screens or select the channels in non menu state CH Used to move around the menu screens or select the the channels in non menu state 17 OK Used to confirm a selection in a menu 18 MENU Used to open the main menu window 19 SETUP Used to adjust the brightness contrast color hue parameter of TFT screen when there is no menu on the screen 20 SCREEN Used to close or open the TFT screen backlight when there is no menu on the screen Used to display information about the channel being viewed or special function indicated on the menu AUDIO Used to exchange the audio language or the audio track Used to display the Electronic Program Guide menu window Navigate Right the menu screens or increase the volume Navigate Left the menu screens or decrease the volume 3 Note 1 SUBTITLE LANGUAGE TEXT may not ava
14. o select different option 6 Press lt Left Right gt button to select different values 7 Press lt 0 9 gt to input the frequency 8 Press lt OK Exit gt button to start Manual Scan or exit See Figure 4 7 Once the channel scan is finished and all the channels are stored into the database you can start to watch the digital terrestrial TV channel or listen to the radio broadcast some typical operations are given in this chapter 2 1 Main Menu Main Menu for operating a lot of functions 1 Press lt Menu gt button to enter Main Menu See Figure 1 2 Press lt Info gt button to display the version information of STB 2 2 SETUP Set the system settings of STB See Figure 1 2 Menu Operations 2 2 1 Installation Set the receiving and playing program settings of STB See Figure 2 2 2 1 1 Antenna Setting Set the antenna power on or off to supply 5V power to antenna or not Note The default is OFF set this option to ON only if this STB is connected to an active antenna which amplifies the received RF signal otherwise please set it to OFF 2 2 1 2 Country Setting Set the country for Auto Scan Manual Scan and Time Zone Note Change the Country Setting will automatically change the default Time Zone and set the default Frequency and Bandwidth for Auto Scan 2 2 1 3 OSD Language Set the On Screen Display Language 2 2 1 4 Audio Language Set the audio language for watching program 2 2 1 5 Subtitle Language Set t
15. on to adjust volume while playing Figure 10 My Music Browser 2 5 ACCESSORY There are three options Gomoku Calendar Calculator Gomoku Press lt Up Down Left Right gt button to set play mode and difficulty Press lt OK gt button to start play Gomoku Press lt Up Down Left Right gt button to select the position Press lt OK gt button to place the piece Calendar displays the year month and date Calculator can used for mathematical calculations Figure 11 Normal Play Radio 3 Normal Play Normal Play means STB under watching TV or listening to the Radio See Figure 11 3 1 Information Press lt Info gt button once to display info banner Banner displays the program No favorite setting current time program name now and next event lock scramble subtitle and teletext info Press lt Info gt button when banner exist to display detail info of now event Press lt Info gt button when detail exist to display current program info See Figure 12 Figure 12 Program Info 3 2 Switch Program User can switch program by UP DOWN or input program number directly If the input program number doesn t exist STB will ignore the input Or press lt Recall gt button to switch to last watching program from current watching program 3 3 Volume Press lt LEFT RIGHT gt button to adjust the volume Press lt Mute gt button to mute If adjust the volume while mute mute will be canceled 12 3 4 Program List Press lt O
16. s When operating range becomes reduced replace all batteries with new fresh ones If leakage from the battery occurs wipe the battery liquid from the battery compartment then replace Built in Rechargeable Battery Management This portable TV used a smart battery management system inside which can support low battery detection 1 If the battery voltage falls below a specific value the unit will enter low battery mode displaying a flashing low battery icon in the OSD indicating the user needs to recharge the TV immediately 2 If the AC DC adapter is connected it will supply the unit with power and the battery will be charged automatically whatever the power switch is ON or OFF 3 If the user keep on watching without connect with the fitted DC adaptor after the battery exhausted an empty battery icon will display and blink at the left up corner the TFT screen will turn into black instead of display the picture and the audio will be muted But the system are still working if the user plug the DC adaptor at this time in time the system will back to normal working mode the video and audio will reproduce again 4 1 Front View 2 Right View 1 AV IN JACK This jack used to connect a external CVBS video and analog audio input 2 AV OUT JACK This jack outputs CVBS video and analog audio signal EARPHONE JACK This jack outputs analog audio L R signal to earphone POWER SWITCH This switch used to switch on off the syste
17. ss lt OK Exit gt button to exit subtitle setting page Figure 16 Subtitle Setting Page Figure 15 Teletext Setting Page 3 10 Teletext Subtitle Display subtitle by teletext the style of the teletext subtitle may be different by content provider Press lt Text Subtitle gt button to display teletext or subtitle setting page Press lt Left Right gt button to select TTX Subtitle Press lt Up Down gt button to select teletext subtitle language Press lt OK Exit gt button to exit the setting page 3 7 Favorites User can switch the favorite programs in the same favorite group About favorites setting see section 2 3 1 1 for details Press lt YELLOW gt button to switch the favorite group in Program list Press button to switch the same favorite program in normal play mode lt FAV gt 3 11 Guide Press lt GUIDE gt button at normal play state see section 2 3 2 for details 3 12 List Press lt GREEN gt button at normal play state see section 2 3 1 for details 14 Problem No signal found No picture or sound Encrypted channel message No response from remote control Square blocks in picture or picture freezes Probable cause Aerial is disconnected Aerial is damaged misaligned Out of digital signal area Viewing incorrect output It is a pay per view channel Set top box is switched off Remote control is not aimed correctly Front panel obstructed Remote control batteries inserted incorrectly Re
18. sword and censorship threshold The censorship info is in program content Under the censorship rating user has to enter the right password for watching program 2 2 3 4 Change Password To change the PIN code select this option press lt Left Right gt button to trigger changing password and lt 0 9 gt buttons to enter old password new password and confirm new password If succeed the PIN Code Changed message will be displayed otherwise the PIN Code Error message will be displayed 2 2 4 Advance Timer User can set timer for watching the program by date and time manually or from the TV Radio Guide see section 2 3 2 When setting date and start time is arrived STB will automatically switch to the wanted program Press any key except lt Vol Vol Mute gt button STB asks user to abort it or not when watching booked program User can delete the event while it isn t at running 2 2 5 Set Default Restore STB to factory default All settings did by user will be restored to factory default values and the database will be erased together 2 2 2 TV Setup Setup the display mode for TV See Figure 5 2 2 2 1 TV Mode Set PAL NTSC or AUTO for display AUTO will switch PAL or NTSC by program content This setting should be matched with user s TV 2 2 2 2 OSD Transparency Set the On Screen Display transparency 1 is the most transparent 9 2 3 TV RADIO There are two types of program TV and Radio The operation of the List and Guide of TV
Download Pdf Manuals
Related Search