KRAM 84324 car kit
Contents
1. the boot below the navigation unit and CD changer unit It may be necessary to completely remove the left boot interior panel An Audio2Car extension cable item no AE5 is also required e Mercedes ML amp GL class with Harman Kardon sound system code 810 Install on amplifier placed under the drivers seat Under the carpet there is small room where the amplifier is located It may be necessary to completely remove the drivers seat An Audio2Car extension cable item no AE4 is also required e Renault cars install on CD player in front on amplifier located inside dash behind above glove box below front seat or in the boot An Audio2Car extension cable may be required Please check the complete cable list for a description of the radio amplifier unit location for the specific car model e Volvo C30 with High Performance sound system install on amplifier behind rear side speaker right side in left hand drive cars and left side in right hand drive cars An Audio2Car extension cable item no AES is also required o Volvo 40 amp V50 2004 with High Performance sound system install on amplifier unit behind side panel in boot An Audio2Car extension cable item no AE5 is also required e Volvo XC60 V70 XC70 80 XC90 from 2006 with High Performance sound system install on amplifier below front passenger seat An Audio2Car extension cable item no AE4 is also required 3rd Connect the car specific cable Disconnect the connector on the radi2. Audio ZCar Audio ZCar The professional mute The professional mute Audio2Car harness Product Description The Audio2Car range allows OEM car speakers to be used for aftermarket Audio equipment Audio2Car allow the car speakers to be used for audio playback from aftermarket Audio equipment For a com plete installation two or more item numbers are required See description at the last page For a complete installation normally a minimum of two item numbers are re quired Audio equipment with build in mute function If the Audio equipment is equipped with a build in mute function two item numbers are required The 1st item number is the Audio2Car harness The 2nd item is a Audio2Car carkit adaptor Audio equipment without build in mute function If the Audio equipment is not equipped with speaker relays a Mute box from Kram Drive amp Talk range can be added together with a Drive amp Talk carkit adaptor Speaker function This is achieved by connecting Audio equipment with build in speaker relay function or by using a Mute box from the Kram range This way the radio sound is muted and the sound from the aftermarket Audio equipment is sent through the car speakers You will achieve a perfect sound without interference from the car radio Mute wire function The mute wire is connected from the 24 pin connector to the most used mute position for the car model This enables the use of the radios built in mute function If the radio does n
3. key in the ignition See installation step 4 Not all speakers are muted Try to disconnect the Carkit adaptor or mute box from the Audio2Car harness then turn on the radio and check the following 1 All speakers keep playing This is the wrong Audio2Car harness for this car sound system 2 Only a few speakers keep playing The mute wire needs to be connected see installation step 5 or this is the wrong Audio2Car harness for this car sound system 3 All speakers are now muted e Carkits with 1 speaker mute Some carkits can only mute 1 speaker channel with their build in mute box This is normally stated on the label on the carkit adaptor for these carkits else please check the carkit manual If a full mute is desired with these carkits then this can be achieved by either connecting the mute wire see installation step 5 Or adding a mute box from our Drive amp Talk range e Carkits with 4 speaker mute or when Kram mute box is used The carkit is defective please replace the carkit Radio will not turn on or not working properly after installation 1 Please check for a blown fuse at the radio or in the car fuse box 2 Remove the Audio2Car harness and connect the radio to the original car connector If the radio is now working replace the Audio2car harness See our complete Radio Mute program on our website www kram dk
4. nstallation description for car specific Audio2Car harness Bullet C t Needed items re ory sy A Audio2Car harness B Audio2Car carkit adaptor or Mute box from our Drive amp Talk range see last page C Carkit Note The Carkit C and Audio2Car carkit adaptor B bought sepa rately A Audio2Car Harness Item number 84xxx 24 pin Connectors gt Installation 1st Remove the key from the ignition barrel This is done to avoid error messages on the cars electrical system Note On some cars it may even be necessary to remove the ground pole from the car battery B Audio2Car Adaptor Item number AAxxx 2nd Locate amp uncover the radio amplifier unit The radio amplifier unit is normally found in the front of the car where the CD player or radio tuner is located Cars with special radio amplifier locations e BMWs with navigation system often has the radio unit behind side panel in boot For these cars an Audio2Car extension cable item no AE5 is also required e BMW X5 has the radio unit located in the spare wheel well An Audio2Car extension cable item no AES is also required e Mercedes A B C amp CLK class with sound system upgrade code 810 install on amplifier behind right side panel in boot just behind the rear wheel arch An Audio2Car extension cable item no AE5 is also required e Mercedes CL amp S class with BOSE sound system code 810 install on amplifier placed in the left side of
5. o amplifier unit and insert the Audio2Car harness between the connector and radio amplifier unit Note Some radios may require a security code to be entered after the power connectors have been removed Ath Connect the blue ignition wire If an ignition source exists in the connector on the Audio2Car harness the blue ignition wire is connected to this position If no ignition source is available in the connector then the blue Audio2Ccar The professional mute ignition wire is connected to the constant 12v source with a bullet connector If an ignition source is needed for the chosen carkit IGNIBOX item no I can be inserted to create an artificial ignition source or the blue ignition wire can be disconnected from the red constant 12v and manually connected to an ignition source found else where 5th Connect the mute wire If a Mute input exists in the connector on the Audio2Car harness the yellow mute wire is connected to this position when delivered If no Mute input is available in the connector then the yellow mute wire is found close to the male connector fitted with a bullet connector It can then be manually con nected to a mute input Connecting the mute wire is an option but may be required in some cars to achieve a full mute of all speakers Note Not all cars are equipped with a mute input 6th Check fuse size The fuse on the Audio2Car cable should not be bigger than the ones used on the wiring loom supplied with
6. ot have such function or the mute exists in a different connector than the ones used on the Audio2Car harness the mute wire can be found in a yellow fly wire fitted with a bullet connector Audio2Car Carkit Adaptors Power supply All Audio2Car cables have an integrated power supply for the Audio equipment in the 24 pin vs connector The constant 12v and the ground supply are normally sourced from the radio supply This way power supply of most Audio Equipment can be achieved without cutting the cars wiring loom The constant 12V wires Several different carkit adaptors j are red and the ground wires are black are available for Carkits that have a build in mute function for 1 or 4 Speakers Please see the complete range of Audio2Car carkit adaptors at our website www kram dk Ignition supply If an ignition source is available in the radio connector then it will normally also be available in the 24 pin connector If an ignition source is not available a constant 12V source is connected to the Ignition pin via bullet connectors If a real ignition is required for the chosen Audio Equipment an IGNIBOX item no I can be connected to create an artificial ignition Or an ignition source found elsewhere can be connected to the bullet with the blue wire The 12V ignition wires in the Audio2Car cable are blue Aux integration The 4 pin connector on the Audio2Car harness allow a Kram Aux solution to be connected This will allow the Exam
7. ples of ee use of the car sound system amplifier for Music playback and thereby achieving higher sound quality carkit adaptors Technical Specifications Description L shaped with bullet connections for Ground Constant 12v and Ignition Drive amp talk Mute box Normal Wire dimensions AWG 18 for power wires AWG 20 for all other wires range Standard Fuse sizes 2 Amp for constant supply 1 Amp for Ignition supply Maximum Fuse size 7 5 Amp for constant supply 7 5 Amp for Ignition supply Maximum output pr speaker 100 Watt RMS 200 Watt music power 4 Ohm Size 400 x 400 mm i vee Configuration chart for 24 pin connector Several different types of mute boxes are on ae ee ea res ea oe a a lt i ue Const IGN OutL OutR RR RF LF LR LR LF RF RR is a os aad ae a la a Pi turn your Audio2Car cable into a Kram saa z i j i 2 u t t t d a 7 hin a 7 A ee i oe ey 2 lt Drive amp Talk solution Therefore you will Mute Line Line Radio Radio Radio Radio Spk Spk Spk Spk ee also need a Drive amp Talk carkit adaptor Out L Out R RR RF LF PLR LR LF RF RR Adding this adaptor turns your Audio2Car cable does P Please see the Complete Drive amp Talk your Audio2Car cable into a not include an ignition source range at our website Connector seen from cable entry side Kram ISO2CAR solution This adaptor is plug and play vwa kimik with your Audio2Car cable EN003 V01 Audio ZCar The professional mute I
8. the carkit The fuses on the Audio2Car cable should be replaced with a size similar to the ones supplied with the carkit Note Never exceed the Maximum Fuse size for the Audio2Car cable See first page 7th Connect the carkit adaptor or Drive amp Talk Mute box Connect the carkit adaptor to the 24 pin connec tor on the Audio2Car harness Connect the carkit adaptor to the carkit Troubleshooting Guide Carkit does not start up Check if there is 12V between the black and the red wire and also between the black and blue wire in the 24 pin connector when the car is started If there is not 12v on both wires please check the following 1 If there is supply on the red constant 12v wire but not on the blue ignition wire the car may require an alternative ignition source See installation step 4 2 Check that the bullets on the supply wires are properly connected The supply wires are the red blue and black wires 3 Check for a blown fuse on the Audio2Car harness or in the cars fuse box The carkit does not turn off when the key is removed from the ignition barrel Your carkits needs a real igni tion source Please check the following 1 Is the blue ignition wire connected to the red constant 12v wire with a bullet connector If this is the case then there is no ignition supply in the radio connector See installation step 4 2 Is there an ignition supply on the blue wire There should be no voltage on the blue wire when there is no
Download Pdf Manuals
Related Search