Whirlpool AKM 489
Contents
1. is removed and the openings on the burner are not blocked The internal burner cap D on page 2 is made of brass and is subject to a natural burnishing when it heats up Clean it each time you use it with a product specifically designed for brass Use hot water and a mild detergent to clean the wok burner external cap item C on page 2 Never use harsh products or scourers that will damage the special surface coverings 2 Rinse and dry carefully 3 Correctly refit the burners and caps in their place 4 Make sure that when replacing the pan supports the pan support is located correctly for each burner Note Hobs fitted with electronic ignition and thermocouples must have the ends of the igniters and thermocouples cleaned regularly and frequently in order to operate Please clean them very carefully with a damp cloth Any remaining ingrained food should be removed carefully with a toothpick or similar 28 To avoid damaging the electronic ignition only operate with the burners and pan supports correctly in place TROUBLESHOOTING GUIDE If the hob is not working properly work through this guide before contacting our Customer Care Centre The burner does not ignite or the flame is unsteady Check that I the gas or electricity supply has not been interrupted and that the control knob is turned fully on 2 the gas supply has not run out 3 the openings on the burner have become blocked the end of2. THE PAN SUPPORTS AND WOK SUPPORT Position the pan supports and wok support as indicated in the diagram HOOD AND CABINETRY CLEARANCES MM If a hood is to be installed above the hob refer to the hood installation instructions to ensure the correct height above the hob INJECTOR TABLE CATEGORY II2H3 750 min Control Nominal Reduced Gas pressure Type of gas Type of Injector primary heat Nominal mbar used burner label air X flow consumption heat low mm kW kw min nom max NATURAL wok 145 6 4 20 400 I h 1 40 GAS fast 128 3 00 286 I h 0 90 i7 20 25 Methane semi fast 95 1 65 157 h 0 40 G20 auxiliary 78 1 00 95 0 30 LIQUID wok 100 lI 4 20 305 g h 1 40 PETROLEUM fast 85 3 00 218 g h 0 90 25 30 35 GAS Butane semi fast 65 1 65 120 g h 0 40 G30 auxiliary 50 1 00 73 g h 0 30 LIQUID wok 100 lI 4 20 300 g h 1 40 PETROLEUM fast 85 3 00 214 g h 0 90 25 30 35 GAS Propane semi fast 65 1 65 118 g h 0 40 G31 auxiliary 50 1 00 71 g h 0 30 Required air m3 Type of gas used Configuration Nominal heat Overall nominal for the model flow kW consumption combustion m of gas G20 20 mbar 5 burners 11 50 1090 l h 9 52 G30 28 30 mbar 5 burners 11 50 836 g h 30 94 G31 37 mbar 5 burners 11 50 821 g h 23 80 Electric Power 230 V 50 Hz 20 WARNINGS AND SUGGESTIONS To get the
3. disconnect the hob from the electrical power supply and wait until it cools before cleaning and or doing maintenance work In order to keep your hob in good condition you must keep it clean removing any food residue each time you use it Cleaning the hob surface the stainless steel surface may become stained if it comes into contact with hard water over along period of time or with extremely strong aggressive cleaning products Always clean any spillages as quickly as possible sauce water etc Wash with lukewarm water and a mild detergent rinse and dry carefully with a soft cloth or a cloth designed to clean stainless steel Only use stainless steel cleaning products on the stainless steel trim Do not use harsh or corrosive products chloride based products or scourers Do not steam clean Do not use inflammable products e Do not leave acidic or alkaline based products like vinegar mustard salt sugar or lemon juice lying on the hob as this will damage the hob and etch the glass surface Note With time regular use of the hob could cause some discolouration around the burners This is caused by the high temperature of the flame and will not affect the operation or performance of the hob CARE AND MAINTENANCE OF THE GAS BURNERS The pan supports and burners can be removed to make cleaning easier I Hand wash carefully in hot water with a mild detergent making sure that all the ingrained dirt
4. for the environment and human health The symbol X on the product or on the documents accompanying this appliance indicates that this product should not be disposed of as household waste Please dispose of this appliance at an Electrical amp Electronic Equipment Collection point as in accordance with local environmental regulations for waste disposal For details of your local Collection Point please contact your Local Authority Conformity declaration C This hob was designed built and marketed incompliance with the safety requirements in the Gas CEE Directive 90 396 the safety requirements of Low Voltage Directive 2006 95 EC replacing 73 23 EEC and subsequent amendments the protection requirements of the EMC CEE Directive 89 336 the requirements in CEE Directive 93 68 this appliance was designed to come into contact with foods and complies with EC Regulation 1935 2004 22 Note Incorrect placement of the pan supports can scratch the hob To avoid this always ensure that the rubber feet on the bottom of the pan supports are the only part of the pan supports that touch the hob Do not drag the pan supports across the hob surface e Do not use two burners to cook pan In the event of prolonged usage additional ventilation may be required opening a window or increasing the extraction speed of the hood Warning Keep children away from the hob when in use and don t let t
5. most out of your hob please read the instructions carefully and keep them for future consultation e These instructions are only valid in the countries whose destination symbol is shown on the serial number plate on the hob The packing plastic bags expanded polyurethane etc pose a potential threat to children and should be disposed of carefully e Check the appliance has not been damaged during transportation and remove all protective packing and films before installation This hob cat 3 was designed to be used exclusively for cooking food in household surroundings Any other use for example heating rooms should be regarded as improper and dangerous The installation and connection of this appliance to a gas or electrical supply must be carried out by a competent qualified person in compliance with current legislation This appliance should be installed in compliance with standards in force and only used in well ventilated rooms Read the instructions before installing and using this appliance The pre fitted gas connector and it s supply pressure are shown on the label attached to the bottom of the hob If this type of gas supply is not being used please refer to the section called Adaption to different types of gas supply on page II Note e Incorrect placement of the pan supports can scratch the hob To avoid this always ensure that the rubber feet on the bottom of the pan supports are the only part of
6. types of materials such as masonry metal wood and heat resistant laminate coated wood 90 C 10 0 Q O 99 7o 7 Cut an opening in the worktop to the dimensions shown in the diagram Carefully place the gasket seal on the external outline of the worktop as shown in the diagram below Apply a light but firm pressure to ensure a good adhesion to the work surface Fix the hob into the unit and secure using the fixing brackets provided Note the electrical power cable must be long enough to allow the hob to be lifted out from above 24 FIXING THE HOB TO THE WORK TOP FLUSH FITTED MODEL Important The following procedure must be z 0 r 22 2 6 5 carried out by competent technical personnel iS z only The hob can be installed on or into s 3 a different types of materials such as masonry metal wood and heat resistant laminate coated wood 90 C Cut an opening in the worktop to the dimensions R 11 Z Z P a shown in the diagram Note For laminated worktops with a laminate thickness of less than 3 mm create a recess as shown as on the detailed schematic drawing Before positioning the hob apply the adhesive gasket seal supplied on the underneath edge of the hob itself where the hob will be in contact with the worktop fig 2 Once the seal is in place place the hob into the recess Secure the hob i
7. INSTRUCTIONS FOR USE PRODUCT DESCRIPTION AND SYMBOLS USING THE BURNERS PRACTICAL ADVICE ON USING THE HOB POSITIONING THE PAN SUPPORTS AND WOK SUPPORT HOOD AND CABINETRY CLEARANCES MM INJECTOR TABLE WARNINGS AND SUGGESTIONS SAFEGUARDING THE ENVIRONMENT INSTALLATION FLUSH AND TRADITIONAL FITTING GAS CONNECTION ELECTRICAL CONNECTION FIXING THE HOB TO THE WORK TOP TRADITIONALLY FITTED MODEL FIXING THE HOB TO THE WORK TOP FLUSH FITTED MODEL ADAPTION TO A DIFFERENT TYPE OF GAS SUPPLY REPLACING THE INJECTORS FITTING THE WOK BURNER REGULATING THE MINIMUM FLOW LEVEL OF THE GAS TAPS GENERAL CLEANING amp MAINTENANCE CARE AND MAINTENANCE OF THE GAS BURNERS TROUBLESHOOTING GUIDE AFTER SALES SERVICE PRODUCT DESCRIPTION AND SYMBOLS Removable pan supports kWh auxiliary burner 1 65 kWh semi fast burner 3 kWh fast burner 1 65 kWh semi fast burner Professional wok burner Auxiliary burner control knob Semi fast burner control knob Fast burner control knob 10 Semi fast burner control knob I I Professional wok burner control knob O 20S n BG t a Pt Control Symbols Off A Maximum flame amp Minimum flame USING THE BURNERS To turn on one of the burners I Turn the corresponding control knob anticlockwise until the indicator coincides with the maximum flame symbol A 2 Press the control knob to ignite the burner 3 Once the burner has lit keep the control knob pressed for about 5 seconds to a
8. b Once you have removed the glass hob you can access the wok burner injector Remove the injector F using a 10 mm spanner 5 Slacken the holding screw H to regulate the position X of the gas inlet coupling G with regard to the injector gt 26 FITTING THE WOK BURNER To fit the double crown wok burner Insert in the following order ane I burner ring A x 2 decorative covering ring B 3 external burner cap C coe 4 4 internal burner cap D es Note make sure that I the locating pin for the burner ring A is inserted correctly in a the slot on the burner unit 2 that the locating pin on the gt external burner cap C is inserted in the slot on the burner ring A REGULATING THE MINIMUM FLOW LEVEL OF THE GAS TAPS Regulating the minimum flow level must be done with the tap at the lowest position small flame There is no need to regulate the primary air in the burners To ensure the minimum level is properly regulated remove the control knob and adjust the screws found on the tap as follows l tighten to reduce the height of the flame 2 slacken to increase the height of the flame 3 With the burners on rotate the buttons from the maximum A to the minimum position to check the stability of the flame Once you have finished regulating close up the seals again using sealing wax 27 GENERAL CLEANING amp MAINTENANCE Always
9. e hob and the injector table The cabinetry and appliances surrounding next to the hob are heat resistant and in compliance with local regulations GAS CONNECTION The products of combustion are removed from the atmosphere in the room by using an extraction hood or electrical fan installed to the walls and or windows in line with current regulations The air circulates naturally through a suitable opening that is no less than 100 cm in cross section which must be permanent and accessible on the walls of the room being ventilated and extracting towards the outside created in such a way that the openings both inside and out cannot be obstructed even by accident Protected by plastic grill and metallic netting etc that should not reduce the 100 cm cross section Located in sucha position so as not to interfere with the extraction of the products of combustion Connection to the mains gas system must be carried out by a competent registered person in compliance with current legislation e The connection of the hob to the gas mains network or gas cylinder must be done using a rigid copper or steel pipe with parts that comply with local standards or using a flexible stainless steel pipe with continuous surfaces that comply with L B local standards The flexible metallic pipe should be no longer than 2 linear metres Before connecting the pipe with the rubber part A insert the sea
10. er Care Centre on 00800 38 10 4026 or a qualified electrician Injectors not supplied as standard should be requested from the Customer Care Centre on 00800 38 10 4026 e Regulate the minimum levels of the taps Note with liquid petroleum gas G30 G3 1 the bypass screw must be screwed in fully If you then experience difficulty in turning the control knob contact our After sales Service though our Customer Care Centre on 00800 38 1 0 4026 who will arrange for a replacement after ascertaining that the tap is damaged REPLACING THE INJECTORS Note Refer to the injector table to ensure the correct type of injector is to be fitted Traditional burners T Remove the pan supports A I 2 Remove the burners B T 3 Unscrew the injector C with a no 7 box spanner at US 4 Replace the injector with one suitable for the new gas type Ss 5 Replace burners and pan supports Note Before installing the hob please remember to stick the gas calibration label provided with the replacement injectors over the gas information on the underside of the hob Wok Burner W It is best to change the wok double crown burner before starting installation I Lift out the hob from the work surface removing the installation fixing pieces 2 Remove the screws securing the glass at the back of the hob plate and those located on both sides of the hob E 3 Remove the holding screws that fix the burner to the glass ho
11. hem play with the control knobs or any other part of the appliance Do not let children play with the pan supports The rubber feet on the underneath of the pan supports could be swallowed by small children and cause serious injury or suffocation Before replacing the pan supports on the hob please check that all the rubber feet are in place Each time you finish using the hob always check that the control knobs are in the off position and shut off the tap to the gas mains or cylinder Do not obstruct the air vents at the back of the appliance in any way INSTALLATION FLUSH AND TRADITIONAL FITTING Technical information for the installer This appliance can be installed into a 20 mm 50 mm thick worktop If no oven is to be installed below the hob a panel must be fitted under the hob to prevent hob damage and protect the cupboard contents This panel must cover the whole of the underside of the hob and must be positioned so that an air gap of at least 50 mm between the panel and hob underside is maintained as a minimum and as a maximum 150 mm to the underneath of the work surface This hob is designed to operate perfectly with any oven in the Whirlpool range The Manufacturer declines all responsibility should another make of oven be installed Before installation please ensure that The gas supply type and pressure and the calibration on the hob are compatible see serial number plate on th
12. l B is in place this part provided complies with EN 549 Warning if you use a stainless steel flexible pipe it must be installed in such a way that it does not come into contact with moving cabinetry like drawers or kitchen cupboards and passes at a point free of obstacles where it can be examined in its entirety e After connecting to the gas mains use soap and water to check there are no leaks 23 ELECTRICAL CONNECTION The electrical connections must comply with current legislation and be carried out by a qualified competent person Information on the voltage and power absorbed are L shown on the serial no plate The appliance must be earthed Earth When installing the appliance we recommend that this yellow green hob is protected by a 3 mm bi polar switch N If damaged the power cable must be replaced with an identical type of power cable HO5V2V2 FT90 C or HO5RR F type We recommend that this operation be conducted by our After Sales Service Please contact our Customer Care Centre on 00800 3810 4026 Do not use extension cables The manufacturer declines all responsibility for damage to persons pets or goods as a result of failure to comply with the regulations above FIXING THE HOB TO THE WORK TOP TRADITIONALLY FITTED MODEL Important The following procedure must be carried out 4 sse 7 by competent technical personnel only The hob can be installed on or into different
13. llow the safety thermocouple fitted to each burner to engage The thermocouple will switch off the gas supply to the burner should the flame be accidentally lost A gust of air momentary interruption of gas supply or liquid spillage etc If the burner does not ignite within about 15 seconds switch off the burner check the fitting of the burner cap and plate for correct fitting Wait at least minute before trying again If the burner goes out when the control knob is released the thermocouple did not engage wait at least minute before repeating steps I to 3 PRACTICAL ADVICE ON USING THE HOB Read the instructions to get the best out of your Important hob Do not rest or drag the pan supports upside down Use pans with a similar diameter to the burner on the hob as this could scratch it see the table on this page Failure to comply with these recommendations could lead to the glass Use flat bottomed pans except with the wok support ceramic hob being damaged or broken and Do not use excessive water when cooking foods the safety of your appliance being and use the lid compromised Ensure that pans are fully supported by the pan supports and do not protrude over the edges You should never use two burners simultaneously with just one Burner Pan diameter container such as a fish kettle wok from 24 to 26 cm fast from 24 to 26 cm semi fast from 16 to 24 cm auxiliary from 8 to 14 cm POSITIONING
14. nto the work surface using the screws and brackets provided tightening them until the hob is perfectly flush fig 3 Carefully trim off the excess gasket seal In case of installation on wood particularly chipboard any small spaces between the edge of the worktop and the hob should be filled with small quantities of silicon sealant see fig 4 Once the appliance has been installed the bottom of the hob should be completely accessible Important tighten the fixing brackets of the hob to the work top by hand using minimum force In case of wooden or similar worktops before fitting the adhesive seal protect the surface of the milled recess with a primer Slots for extra brackets have been created on the bottom of the appliance to help achieve a more flush positioning should this be necessary Appropriate brackets can be obtained from the Customer Care Centre E D Fig Fig 2 Fig 3 Fig 4 25 ADAPTION TO A DIFFERENT TYPE OF GAS SUPPLY If you are using a different kind of gas from the one indicated on the serial no plate and the orange label on the back of the hob you must replace the injectors in the case of the Wok burner adjust the primary air see Injector table on page 6 The orange label should be removed and kept together with the manual Use pressure regulators suitable for the gas pressures indicated on page 6 In order to replace the injectors contact the Custom
15. the electronic igniter is clean 5 all the parts on the burner are properly positioned gt AFTER SALES SERVICE Before contacting our Customer Care Centre please check to see if the problem can be fixed by referring to the troubleshooting guide l If the fault persists contact us on 00800 38 0 4026 We will ask you for some information it will help us help you if you have the following information ready to give us a short description of the fault the serial number and model number of the appliance e the service number the number after the word service on the rating plate on the bottom of the hob The service number can also be found in the warranty booklet The flame doesn t stay on Check that I the button was pushed in properly when turning on the burner for the time required to activate the safety thermocouple 2 the burner s openings are not blocked near or around the thermocouple 3 the end part of the thermocouple is clean The pans are not stable Check that I the bottom of the pan is perfectly flat 2 the pan is centred on the burner 3 the pan supports are correctly positioned with all the rubber feet in place your name full address including postcode and telephone number By gia Kel 0000 000 00000 Note If there is a problem with your hob failure to contact us could seriously compromise the safety and quality of this appliance 29
16. the pan supports that touch the hob and do not drag the pan supports across the hob surface On the glass surface do not use Cast iron grills terracotta pots or pans Heat convectors e g metal netting Using two burners to cook pan In the event of prolonged usage additional ventilation may be required opening a window or increasing the extraction speed of the hood Warning Keep children away from the hob when in use and don t let them play with the control knobs or any other part of the appliance Do not let children play with the pan supports The rubber feet on the underneath of the pan supports could be swallowed by small and cause serious injury or suffocation Before replacing the pan supports on the hob please check that all the rubber feet are in place Each time you finish using the hob always check that the control buttons are in the off position and shut off the tap to the gas mains or cylinder Do not obstruct the air vents at the back of the appliance in any way 21 SAFEGUARDING THE ENVIRONMENT Packing The packing material is 100 recyclable and is labelled with the recycling symbol 4 Please dispose of all packing responsibly and carefully Product This appliance is marked according to the European Directive 2002 96 EC Waste Electrical and Electronic Equipment WEEE By ensuring that this product is disposed of correctly you will help prevent potentially negative consequences
Download Pdf Manuals
Related Search