Toshiba MHZ2120BJ hard disk drive
Contents
1. the disk drive to the host system must be compliant with the Serial ATA Revision 2 6 specification 3 3 5 Note about SATA interface cable connection Take note of the following precaution about plugging a SATA interface cable into the SATA interface connector of the disk drive and plugging the connector into a host receptacle IMPORTANT When plugging together the disk drive SATA interface connector and the host receptacle or SATA interface cable connector do not apply more than 10 kgf of force in the connection direction once they are snugly and securely in position IMPORTANT Connecting removing the cable without releasing the SATA interface Latch may lead to connector damage and the loss of the Latch function Accordingly be sure to connect remove the cable while releasing the Latch C141 E280 3 11 This page is intentionally left blank2. CHAPTER 3 Installation Conditions 3 1 Dimensions 3 2 Mounting 3 3 Connections with Host System This chapter gives the external dimensions installation conditions surface temperature conditions cable connections and switch settings of the hard disk drives C141 E280 Installation Conditions 3 1 Dimensions Figure 3 1 illustrates the dimensions of the disk drive All dimensions are in mm 100 0 4 1 90 6 0 25 1 1420 25 1 5 3t0 25 3 50 38 5 9 40 31 2 exe je 3 69 85 0 25 125 0 28 4 30 The PCA and connectors are not included in these dimensions 2 Dimension from the center of the user tap to the base of the connector pins 3 A Length of the connector pins 4 Dimension from the outer edge of the user tap to the center of the connector pins 5 Dimension from the outer edge of the user tap to the innermost edge of the connector pins Figure 3 1 Dimensions 3 2 C141 E280 3 2 Mounting 3 2 Mounting For information on mounting see the FUJITSU 2 5 INCH HDD INTEGRATION GUIDANCE C141 E144 1 Orientation The disk drives can be mounted in any direction 2 Frame The MR head bias of the HDD disk enclosure DE is zero The mounting frame is connected to Signal Ground SG IMPORTANT Use M3 screw f
3. GRATTLE NOISE 19 NORMAL WHEN HANDLED VOID WARRANTY IF SEAL BROKEN AVOID EXCESSIVE SHOCK RoHS compliance Chuna hve Rood Talpel Tal van MAY BE MANUFACTURED UNDER ONE S PATENT 9 R J 6 178 047 5 339 208 OF FOLLOWING 5 530 875 5 580 001 812 5 700 5 978 187 6 619 518 8 880 982 7 002 788 Fujltsu Korea Ltd XXX XXXXXXXXX X WWN XXXXXXXXXXXXXXXX Hop DO NOT COVER 9 4 Figure 3 3 Location of breather 3 5 Installation Conditions 4 Ambient temperature The temperature conditions for a disk drive mounted in a cabinet refer to the ambient temperature at a point 3 cm from the disk drive The ambient temperature must satisfy the temperature conditions described in Section 1 4 and the airflow must be considered to prevent the DE surface cover temperature from exceeding 60 C Provide air circulation in the cabinet such that the PCA side in particular receives sufficient cooling To check the cooling efficiency measure the surface cover temperatures of the DE Regardless of the ambient temperature this surface cover temperature must meet the standards listed in Table 3 1 Figure 3 4 shows the temperature measurement point Figure 3 4 Surface cover temperature measurement points Table 3 1 Surface temperature measurement points and standard values Measurement point 3 6 C141 E280 3 2 Mounting b Service area Figure 3 5 shows how the drive must be acc
4. essed service areas during and after installation Mounting screw hole Figure 3 5 Service area A CAUTION Data corruption Avoid mounting the disk drive near strong magnetic sources such as loud speakers Ensure that the disk drive is not affected by external magnetic fields Damage Do not press the cover of the disk drive Pressing it too hard the cover and the spindle motor contact which may cause damage to the disk drive Static When handling the device disconnect the body ground 500 kQ or greater Do not touch the printed circuit board but hold it by the edges 6 Handling cautions Please keep the following cautions and handle the HDD under the safety environment C141 E280 3 7 Installation Conditions General notes ESD mat Wrist strap Shock absorbing mat Use the Wrist strap Place the shock absorbing mat on the operation table and place ESD mat on it Do not stack when carrying Do not place HDD vertically to avoid falling down Do not drop Figure 3 6 Handling cautions nstallation 1 Please use the driver of a low impact when you use an electric driver HDD is occasionally damaged by the impact of the driver 2 Please observe the tightening torque of the screw strictly M3 gt 0 49N m 5 kgf cm Recommended equipments Contents Model Maker ESD Wrist strap JX 1200 3056 8 SUMITOMO 3M ESD mat SKY 8A Color Seiden Mat Achilles Shock Low sh
5. ock driver SS 6500 HIOS 3 8 C141 E280 3 3 Connections with Host System 3 3 Connections with Host System 3 3 1 Device connector The disk drive has the SATA interface connectors listed below for connecting external devices Figure 3 7 shows the locations of these connectors and terminals M AS NM SATA interface and power connectors PCA Figure 3 7 Connector locations C141 E280 3 9 Installation Conditions 3 3 2 Signal segment and power supply segment Figure 3 8 shows each segment of the SATA interface connector and pin numbers Il View from the ET connector side Power supply segment View from the PCA side Figure 3 8 Power supply pins CN1 3 3 3 Connector specifications for host system The connector of host system for mating with the disk drive must be compliant with Serial ATA Revision 2 5 specification For detail of requirements about SATA interface connector refer to the Serial ATA Revision 2 6 IMPORTANT The connection reliability per number of insertion extractions varies with the condition of the connection with the host system Therefore we recommend that the customer evaluate the connector on the customer s system and select it from the connectors complying with the Serial ATA Revision 2 6 specification C141 E280 3 3 Connections with Host System 3 3 4 SATA interface cable connection The cable that connects
6. or the mounting screw and the screw length should satisfy the specification in Figure 3 2 The tightening torque must be 0 49Nem Skgfecm When attaching the HDD to the system frame do not allow the system frame to touch parts cover and base other than parts to which the HDD is attached C141 E280 3 3 Installation Conditions 3 Limitation of mounting Note These dimensions are recommended values if it is not possible to satisfy them contact us 2 5 Side surface 2 5 Bottom surface mounting mounting 2 5 2 5 PA la d Frame of system cabinet ONE 3 0 or less SS Screw 3 0 or less Screw Details of A Figure 3 2 Mounting frame structure 3 4 C141 E280 C141 E280 IMPORTANT Because of breather hole mounted to the HDD do not allow this to close during mounting Locating of breather hole is shown as Figure 3 3 3 2 Mounting For breather hole of Figure 3 3 at least do not allow its around 3 to block MANUFACTURED FUJITSU THAILAND CO LTD Fujitsu OCENG MADE IN THAILAND PART NO XXXXXXX XXXXXXXX Talvan Ltd Ful Hau MODEL XXXXXXXXX 1D XK XXX Qor ig Tali Ltd SER NO XXXXXXXXXXXX DATE 200X XX XX ATING t5V 0 XXA REV NO AQ123458789 XXX Me LBA ope ST 449 115 SATA POWER SERIAL DATA pikonga CAUTION PLEASE ATTACH ALL CABLES 5 00e 051 SECURELY FOR PROPER CONNECTION fures DO NOT PUSH ON THE TOP COVER AND PCB
Download Pdf Manuals
Related Search