Altec Lansing IMT800 home audio set
Contents
1. 3 Plug the other end of the stereo cable into your speaker system s AUX 1 or AUX 2 jack The AUX jacks are located on the top of the speaker system next to the handle 4 Select AUX 1 or AUX 2 mode Press the SOURCE button on your speaker system or the clip on remote until Auxiliary Input 1 or Auxiliary Input 2 appears on the speaker system s LCD 5 Turnon your device and start playing it 6 Adjust the volume Use the 5 knob on the speaker system to adjust the volume Or use the and buttons on the clip on remote NOTE You may need to adjust the device volume also Your device s volume should be set to approximately 94 volume Personalizing the Power On Message Whenever you turn on your Altec Lansing Mix speaker system the Altec 2 Clearthe message Lansing logo will appear for approximately 3 seconds followed by a personalized message if you ve set one The Mix comes with no preset power on message To create a personalized message just follow these 3 Exit the Message Screen Edit Mode instructions Press the SOURCE button to clear the message Press the D knob to exit the Message Screen Edit Mode 1 Enter the Message Screen Edit Mode Press and hold the SOURCE EQ nd ii buttons All four Maintaining Your Spea ker System buttons must be pressed at approximately the same time while the Altec Lansing logo is displayed The following message will appear on the LCD2. Do not install in an area which impedes the access to the power plug Disconnecting the power plug is the only way to completely remove power to the product and must be readily accessible at all times Contents WECOME e ii Sateiy lnfelmatior 205 5255 i E eati de A hc act gah EIER EMO ICA Lee UIN Lore detucens LESE EOM A ocLI oL PL DOLES LITE Dra la O ec desea 1 Package Contents Getting Started Placing and Removing Adapters for the iPhone and iPod Speaker Features and Indicators Speaker Controls Clip On Remote Features Listening to Your iPhone or iPod SELIG EQ CMOS arasa E E gee ORR E ET AERA ihn a EA rarer 13 Gharging YOUR MP MONG GEIR OG m T 15 Listening to the FM Radio Listening to Additional iPhone iPod Non Docking iPod or Other Audio Devices Personalizing the Power On Message Maintaining Your Speaker System Troubleshooting Warranty Package Contents Altec Lansing Mix speaker system iscellaneous adapters Q for iPhone and iPod ac AC adapter i 3 cR Two 3 5 mm stereo cables C LE Getting Started How to Install the AC Adapter 5 Replace the battery door 1 Connect the AC adapter cable plug into the speaker system s jack The jack is located on the back of the
3. ALTEL LANSING Altec Lansing Mix Portable Speaker for iPhone and iPod IMT800 User Guide Welcome Thank you for purchasing the Altec Lansing Mix speaker system Designed specifically to work with your iPhone and iPod this system provides high quality audio and radio performance that brings out the best in your music This Altec Lansing speaker system is compatible with all iPhone and iPod models Please carefully read this User Guide for instructions on setting up and using your Mix speaker system Prior to installing or operating the Altec Lansing Mix speaker system refer to the important product safety information Getting Assistance The answers to most setup and performance questions can be found in the Troubleshooting section of this guide You can also consult the frequently asked questions FAQ in the customer support section of our Web site at www alteclansing com If you live in North America and still can t find the information you need please call our customer service team for assistance before returning this product to your retailer under their return policy Tel 800 258 3288 Toll Free in US and Canada Email csupport alteclansing com If you live outside of North America please visit our Web site at www alteclansing com and select your region to locate your country s distributor For the most up to date information be sure to check our Web site at www alteclansing com International Distr
4. Add a personal message by selecting letters with the track buttons and rotary control Place your speaker system on a level surface away from sources of direct sunlight or excessive heat Protect your furniture with a cloth or other protective material when placing 2 Add your personal message your speaker system on a natural wood or lacquered finish Rotate the knob until the desired letter number or symbol is displayed Press the button to make your selection and move to the next space Continue this process until your entire message is displayed Clean your speaker system with a soft cloth moistened only with mild soap and water Stronger cleaning agents such as benzene thinner or similar materials can damage the surface of the unit S Exit the Message Screen Edit Mode Press the D knob to save the message and exit the Message Screen Edit Mode How to Delete a Personalized Message 1 Enter the Message Screen Edit Mode Press and hold the SOURCE EQ nd i buttons All four buttons must be pressed at approximately the same time while the Altec Lansing logo is displayed The following message will appear on the LCD Add a personal message by selecting letters with the track buttons and rotary control 17 18 Troubleshooting Symptom Possible Problem Solution Speaker system doesn t respond no power iPhone or iPod doesn t dock properly AC adapter isn t plugged into a
5. NOTE Please discard used batteries properly NOTE When you are finished listening to your portable audio device System please remember to turn both it and your speaker system off to conserve E electricity 2 Plug the AC adapter into the wall A puer How to Install the Clip On Remote Battery How to Install the Speaker Batteries The clip on remote battery included is not installed at the factory To install the battery follow the steps below The battery compartment is at the back of the remote Push the battery compartment door in the direction of the arrow to unlock it 1 Make sure that there is no iPhone 1 or iPod in the system s dock and that no other devices are connected to the system 2 Unplug the AC adapter from the Mix speaker system Your Altec Lansing Mix speaker system can also be powered by 8 D size LR20 batteries not included To install the batteries follow the steps below Open the battery door The battery door is located on the back of the remote Using your thumb push the battery door toward the carabiner clip Then lift the battery door open 2 Position the battery included so it sits in the battery holder correctly Make sure the polarity the and sides of the battery is correct 3 Open the battery compartment The battery door is located on the bottom of the Mix speaker system To access it place the unit on its back so that the speakers are facin
6. Lansing Mix speaker system s clip on remote enables you to program up to 4 FM station presets 1 Tune to the station you wish to store While in FM mode use the 4 or 1 buttons on your speaker system or clip on remote to tune to the desired station 2 Store the station Press and hold the P1 P2 P3 or P4 button on the clip on remote for a few seconds You can store one FM station in each preset S Tostore other stations repeat the above steps How to Recall Preset Stations 1 Make sure you are in FM mode If you re not in FM mode press the SOURCE button on your speaker system or clip on remote until FM appears on the LCD 2 Press a PRESET button P1 P2 P3 or P4 on the clip on remote The radio will tune to your preset station 3 Adjust the volume Use the D knob on your speaker system to adjust the system volume Or use the and buttons on the clip on remote 15 Listening to Additional iPhone iPod Non Docking iPod or Other Audio Devices If you or a friend has an iPhone iPod non iPod MP3 player or other non docking audio device you can enjoy it through your Altec Lansing Mix speaker system as well Just connect it via the AUX 1 or AUX 2 jack Here s how 1 Locate one of the two 3 5 mm stereo cables included 2 Plug one end of the stereo cable into your device Your device should have either a headphone or LINE OUT jack for you to plug into Rs d n
7. automatically enabling the alarm or sleep timer to play through the speaker System See the user guide for iPhone or iPod for details on how to access these features NOTE During AC operation if there is no iPhone or iPod docked and no audio input signal is detected for a few minutes the speaker system automatically shuts down to conserve energy Press the button on the speaker system or the D button on the clip on remote to turn the speaker System back on 11 12 Listening to Your iPhone or iPod How to Access Additional Features on Your iPhone or iPod Using the Clip on Remote First select iPod mode Press the SOURCE button on your speaker system or clip on remote until the iPod icon appears on the LCD Press the P1 button once on the Repeat function clip on remote to advance to the next shuffle mode e Shuffle S is displayed when the system is in song shuffle mode e Shuffle A is displayed when the Shuffle function system is in album shuffle mode Press the P2 button once on the clip on remote to advance to the next repeat mode Repeat 1 is displayed when the System is in the repeat one mode Repeat is displayed when the System is the repeat all mode Repeat Off is displayed when the repeat function has been turned off Note Use the P1 button on some older iPod models Functionality may vary per iPhone or iPod model e Shuffle Off is displayed when the shuffling functi
8. t work No sound from the AUX 1 or AUX 2 device such as an iPhone iPod MP3 player or CD player connected to the AUX 1 or AUX 2 jack Battery is weak Replace current battery with a new battery Clip on remote is not pointed toward to the speaker system Point the clip on remote toward the Altec Lansing speaker system and move within 10 feet of the unit Sound source is connected to the AUX 1 or AUX 2 jack Volume on the device is set too low Clip on remote will not control devices connected to the AUX 1 or AUX 2 jack Increase the volume on the device to approximately 94 full volume Source selector is not set to AUX 1 or AUX 2 Set source selector to AUX 1 or AUX 2 The speaker system exhibits erratic or unexpected behavior Controls do not function Static electricity momentary interruption of power or abnormal operating conditions may be responsible 1 Disconnect the AC adapter cable plug from the speaker system s jack 2 Wait 20 30 seconds 3 Reconnect the AC adapter cable plug to the speaker system s jack 4 Turn the unit back on There is radio interference The unit is too close to a radio tower Move the unit to see if the interference goes away ALTEC LANSING ONE YEAR LIMITED WARRANTY What Does the Warranty Cover Altec Lansing warrants that its products shall be free from defects in materials or workmanship with the exceptions stated below What Is the P
9. the iPod icon appears on the LCD Press the 11 button on your iPhone iPod or clip on remote Music from your iPhone or iPod will start playing The speaker system and the clip on remote are capable of controlling basic functions of 8rd generation iPod models the iPod touch the iPod nano and the iPhone Adjust the volume Rotate the D knob on the Altec Lansing speaker system to adjust the Qm system volume Or use the and buttons on the clip on remote Find your desired song Press the or si button on your speaker system or clip on remote to go to the next or previous track Press and hold the or t button on your speaker system or clip on remote while the track is playing for high speed forward or reverse music search of the current track Listening to Your iPhone or iPod NOTE To conserve battery power reduce the speaker system volume level NOTE During battery only operation the speaker system automatically shuts down if no audio is detected for a few minutes This is to conserve battery power Press the D button on the speaker system or the D button on the clip on remote to turn the speaker system back on NOTE The speaker system is compatible with the alarm clock and sleep timer features built into select iPhone and iPod models For these features to work properly the speaker system must be connected to a wall outlet When an iPhone or iPod is docked the speaker system will not shut down
10. EQ Presets Using the Onboard Controls 1 Access the EQ presets Press and hold the EQ button for approximately 3 seconds 2 Select your desired preset Press the or tt buttons to cycle through the four EQ presets Presets include 1 ALTEC EQ 2 ROCK 3 HIP HOP and 4 POP S Exitthe EQ Preset screen Press the EQ button again Or the unit will automatically exit this screen after a few seconds NOTE To reset the EQ Presets to factory settings press and hold the EQ button for a few seconds How to Change the EQ Presets Using the Clip On Remote 1 Access the EQ presets Press and hold the EQ button for approximately 3 seconds 2 Select your desired preset Press the or k buttons to cycle through the four EQ presets Presets include 1 ALTEC EQ 2 ROCK 3 HIP HOP and 4 POP Or press P1 for ALTEC EQ P2 for ROCK P3 for HIP HOP or P4 for POP S Exitthe EQ Preset screen Press the EQ button again Or the unit will automatically exit this screen after a few seconds 18 14 Setting EQ Controls NOTE You can personalize the EQ presets by selecting a Preset EQ then pressing the EQ button twice to enter the Bass Treble Control Mode There you can make adjustments to the Preset EQs as described in the Bass and Treble Control sections Changes are saved automatically NOTE To reset the EQ Presets to factory settings press and hold the EQ button for a few seconds How to Adjust the 7 Band Graphic EQ Usi
11. Q button Track forward button Source button FM antenna Two AUX jacks LCD display Battery indicator FM stereo indicator AC adapter jack Guard for iPhone or iPod Universal docking station for iPhone or iPod Speaker Controls Turn on your speaker system Ensure the AC adapter is connected to the system and plugged into the wall See the Getting Started section for more information Press the knob Turn off your speaker system Press the D knob Whenever you are finished using your speaker system please remember to turn it and your iPhone iPod or other MP3 player off to conserve electricity Change audio source Press the SOURCE button to cycle through and select the audio source iPod FM radio AUX 1 or AUX 2 Set the graphic equalizer See the Setting EQ Controls section for specific information on selecting EQ presets and adjusting the 7 band graphic EQ Turn up the volume Rotate the D knob clockwise Turn down the volume Rotate the knob counter clockwise Skip to your iP the beginning of the current song on hone or iPod n iPod mode press the t button Rewind iPhone the currently playing track on your or iPod n iPod mode press and hold Skip to your iP the beginning of the next song on hone or iPod n iPod mode press the button Fast forward the curre
12. e contact your local recycling center for proper battery handling and disposal instructions POWER SOURCE Use only power supplies of the type specified in the operating instructions or as marked on the appliance If a separate power supply is included with this apparatus do not substitute with any other power supply use only manufacturer provided power supplies CAUTION To prevent electric shock do not use this polarized plug with an extension cord receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure WARNING To reduce the risk of fire or electric shock do not expose this appliance to rain or moisture IMPORTANT SAFETY INSTRUCTIONS 1 Read these instructions Keep these instructions Heed all warnings Follow all instructions o RONM Do not use this apparatus near water This apparatus shall not be exposed to dripping or splashing and no objects filled with liquids such as vases shall be placed on the apparatus 6 Clean only with dry cloth Caution To prevent the risk of electric shock do not remove cover or back No user serviceable parts inside Refer servicing to qualified service personnel The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance Do not block any ventilation openings Install in accorda
13. e make sure your iPhone or iPod is working properly before docking into the unit Please refer to your iPhone or iPod manual for details Using 1st or 2nd generation iPod iPod shuffle or other devices Your speaker system cannot control those iPods or other devices iPhone or iPod didn t charge iPhone or iPod is not installed properly Remove your iPhone or iPod from the dock and check for obstructions on the connectors in the dock and on your iPhone or iPod Then reseat it in the dock and slide the guard down to protect it iPhone or iPod is locked up Please make sure your iPhone or iPod is working properly before docking into the unit Please refer to your iPhone or iPod manual for details AC adapter isn t plugged into a wall outlet or the connector is not plugged into the power supply jack on the back of the speaker system Plug the AC adapter into a wall outlet and plug the connector into the supply jack on the speaker system The iPhone or iPod will not charge when the speaker system is operating on batteries 19 20 Troubleshooting Symptom Possible Problem Solution Sound is distorted EQ settings are set too high Decrease the EQ settings Sound source is distorted If the iPhone or iPod original sound source MP3 is of poor quality distortion and noise are easily noticed with high power speakers Try a different audio Source such as a music CD Clip on remote doesn
14. eriod of Coverage This warranty runs for one year from the date of purchase The term of any warranties implied by law shall expire when your limited warranty expires Some states and or Member States in the European Union do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you What Does the Warranty Not Cover This warranty does not cover any defect malfunction or failure that occurs as a result of improper installation misuse or failure to follow the product directions abuse or use with improper unintended or faulty equipment For information on proper installation operation and use consult the manual supplied with the product If you require a replacement manual you may download a manual from www alteclansing com Also consequential and incidental damages are not recoverable under this warranty Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you What Will Altec Lansing Do to Correct the Problem Altec Lansing will at its option repair or replace any product that proves to be defective in material or workmanship If your product is no longer being manufactured or is out of OCk at its option Altec Lansing may replace your product with a similar or better Altec Lansing product Q How to Get Warranty Service To get a covered product repaired or replaced you must contact Al
15. g 2009 Plantronics Inc All rights reserved ALTEC ALTEC LANSING the Altec Lansing logo the horn design Mix and iMT800 are trademarks or registered trademarks of Altec Lansing a division of Plantronics Inc Plantronics the logo design and Sound Innovation are trademarks or registered trademarks of Plantronics Inc iPod is a trademark of Apple Inc registered in the U S and other countries ES iPhone is a trademark of Apple Inc All other trademarks appearing herein are the property of their respective owners Designed by Altec Lansing in the USA Made in China A13238 R04
16. g the ceiling Then simply pull the S Replace the battery door tabs to open the battery compartment NOTE Please discard used batteries properly Caution Do not place the unit on its top side This may damage the volume knob 4 Install 8 D size LR20 batteries not included in the battery compartment Make sure the batteries are correctly installed as illustrated in the battery compartment The batteries will provide up to 30 hours of continuous playing time Placing and Removing Adapters for the iPhone and iPod Your Altec Lansing Mix speaker system includes removable adapters for today s popular iPhone and iPod models These adapters ensure that your iPhone and iPod properly fit in the speaker system s dock As new iPhone and iPod models are introduced new adapters will be made available to customers You may also use the adapter supplied with your iPhone or iPod or available for purchase at www apple com How to Place an Adapter 1 Select the correct adapter for your iPhone or iPod Using the correct adapter ensures a proper fit for your iPhone or iPod 2 Gently press the iPhone or iPod adapter into the dock Now you can carefully place your iPhone or iPod into the dock NOTE Your iPhone or iPod cannot be in a case How to Remove an Adapter 1 Remove your iPhone or iPod 2 Grip the adapter and pull gently upward Speaker Features and Indicators Power volume increase Track back button volume decrease knob E
17. he next desired slider is highlighted 5 Increase or decrease the level of the frequency slider Press the or buttons on the clip on remote 6 Continue selecting and adjusting frequency sliders as desired 7 Exit the Graphic EQ Mode Press the EQ button on either the clip on remote or the speaker system Or the unit will automatically exit this mode after several seconds NOTE To reset the Graphic EQ to factory settings press and hold the EQ button for a few seconds Charging Your iPhone or iPod Whenever your iPhone or iPod is docked and your Altec Lansing inMotion Max speaker system is plugged into an AC outlet your iPhone or iPod is charging until fully charged even if the speaker system is switched off Listening to the FM Radio 1 Extend the FM antenna fully for 7 best FM reception 2 Select FM mode Press the SOURCE button on your speaker system or clip on remote until FM appears on the LCD SOURCE S Tune to the station you want to listen to Use the or t buttons on your speaker system or enhanced remote to tune in the desired station Press and hold these same buttons to find the next clear FM station 4 Adjust the volume Use the 5 knob on your speaker system to adjust the system am volume Or use the and buttons on the clip on remote How to Store Preset Stations Your Altec
18. ibution International customers For information regarding the distribution of Altec Lansing products in your country please visit www alteclansing com and click on your region Registering Your Product Visit www alteclansing com to register your product online so we can provide you with the best possible service and technical support FCC Compliance Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 2 This device may not cause harmful interference and This device must accept any interference received including interference that may cause undesired operation RISK OF ELECTRIC SHOCK Safety Information J The lightning flash with arrowhead within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons BATTERIES CAUTION Danger of explosion if battery is incorrectly replaced Replace only with the same or equivalent type Do not expose to excessive heat such as sunshine fire or the like The battery used in this product must be properly recycled or disposed of Instructions for removing the battery can be found in the Quick Start Guide Pleas
19. n its packaging indicates that this product shall not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help EM prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The recycling of materials will help to conserve natural resources For more detailed information about recycling of this product please contact your local city office or your household waste disposal service 21 ALTEL LANSING www alteclansing com HEADQUARTERS 535 Rte 6 amp 209 Milford PA 18337 0277 800 ALTEC 88 570 296 4434 Fax 570 296 6887 EUROPE Scorpius 140 2132 LR Hoofddorp The Netherlands ASIA PACIFIC 23 F Office Tower Shun Hing Square Diwang Commercial Centre 5002 Shen Nan Dong Road Shenzhen China 518008 Made for iPod means that an electronic accessory has been designed to connect specifically to iPod and has been certified by the developer to meet Apple performance standards Works with iPhone means that an electronic accessory has been designed to connect specifically to iPhone and has been certified by the developer to meet Apple performance standards Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards Patents pendin
20. nce with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for the replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 1 Only use attachments accessories specified by the manufacturer Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over Unplug this apparatus during lightning storms or when unused for long periods of time Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped
21. ng the Onboard Controls For even greater personalization of your music you can dial in your sound with the onboard 7 band graphic EQ 1 Enter the Graphic EQ Mode Press and hold the EQ button while you press the tt 2 Selecta frequency slider for adjustment Press the t amp or ii buttons until the desired slider is highlighted S Increase or decrease the level of the frequency slider Rotate the D knob 4 Selectthe next frequency slider for adjustment Press the or 4 buttons until the next desired slider is highlighted 5 Increase or decrease the level of the frequency slider Rotate the X knob 6 Continue selecting and adjusting frequency sliders as desired 7 Exit the Graphic EQ Mode Press the EQ button again Or the unit will automatically exit this mode after several seconds NOTE To reset the Graphic EQ to factory settings press and hold the EQ button for a few seconds How to Adjust the 7 Band Graphic EQ Using the Clip On Remote 1 Enter the Graphic EQ Mode On the speaker system press and hold the EQ button while you press the isi or buttons 2 Selecta frequency slider to adjust Press the or buttons on the clip on remote until the desired slider is highlighted S Increase or decrease the level of the frequency slider Press the or buttons on the clip on remote 4 Select the next frequency slider to adjust Press the t amp or ii buttons on the clip on remote until t
22. ntly playing track on your iP hone or iPod n iPod mode press and hold the si button Tune radio stations n FM mode use the ii and i buttons See the Listening to the Radio section for additional information Speaker Controls Scan radio stations In FM mode press and hold the or pH button See the Listening to the Radio section for additional information Listen to an additional iPhone iPod non docking iPod or other portable audio device See the Listening to Additional iPhone iPod Non Docking iPod or Other Portable Audio Devices section for specific information on using devices attached to your speaker system s AUX jacks Enter a personalized power on message See the Personalizing the Power On Message section for specific information on using this feature Reset all settings With the speaker system turned on press the and i buttons simultaneously for a few seconds Once the word RESET is displayed on the screen press the button to reset all settings Select FM Band region Reset all settings see above and use the t and t buttons to select the region closest to you REGION 1 USA REGION 2 EUROPE ASIA REGION 3 JAPAN WIDE or REGION 4 JAPAN Then press the D knob to save your selection Check battery status If the Mix is being powered by batteries you can see how much battery power you have left Press and hold the SOURCE button to di
23. on has been turned Apecss ea Press the P3 button on the clip on remote off Note Use the P2 button on some Access the next playlist older iPod models Functionality may Press the P4 button on the clip on remote vary per iPhone or iPod model How to Set the Bass and Treble Control Using the Onboard Controls 1 Access the bass and treble settings Press the EQ button once The Bass Control screen will appear on the LCD 2 Increase or decrease the bass level Rotate the knob S Enterthe Treble Control screen Press the EQ button again The Treble Control screen will appear 4 Increase or decrease the treble level Rotate the knob 5 Exitthe Treble Control screen Press the EQ button again Or the unit will automatically exit this screen after a few seconds How to Set the Bass and Treble Control Using the Clip On Remote 1 Access the bass and treble settings Press the EQ button once The Bass Control screen will appear on the LCD 2 Increase or decrease the bass level am Press the or buttons S Enterthe Treble Control screen Press the EQ button again The Treble Control screen will appear 4 Increase or decrease the treble level am Press the or buttons Setting EQ Controls 5 Exit the Treble Control screen Press the EQ button again Or the unit will automatically exit this screen after a few seconds How to Change the
24. splay the amount of battery power remaining and press it again to exit this mode The unit will automatically exit this mode after a few seconds Clip On Remote Features The clip on remote lets you operate many functions of your Altec Lansing Mix speaker system f E PAN Turn on your speaker system Press the D button Source button li l oN i Turn off your speaker system Press the button Volume decrease Press the SOURCE button to cycle button Change audio source through and select the audio source iPod FM radio AUX 1 or AUX 2 rack beckbuftoi Turn up the volume Press the button Turn down the volume Press the button EQ button Skip to the beginning of the current song on your iPhone or iPod n iPod mode press the iii button Rewind the currently playing track on your iPhone or iPoc n iPod mode press and hold button FM preset buttons Skip to the beginning of the next song on your iPhone or iPod n iPod mode press the tt button Fast forward the currently playing track on your iPhone or iPoc Set the graphic equalizer n iPod mode press and hold button Carabineer clip See the Setting EQ Controls section for specific information on selecting EQ presets and adjusting
25. tec Lansing during the warranty period by email csupport alteclansing com You must include in your email your name address email address telephone number date of purchase and a complete description of the problem you are experiencing In the United States you may alternatively contact Altec Lansing by telephone at 1 800 ALTEC88 please be prepared to provide the same information If the problem appears to be related to a defect in material or workmanship Altec Lansing will provide you a return authorization and instructions for return shipment Return shipments shall be at the customer s expense and the return must be accompanied by the original proof of purchase You should insure the shipment as appropriate because you are responsible for the product until it arrives at Altec Lansing Warranty How Will State Law Affect Your Rights This warranty gives you specific legal rights and you may also have other rights which vary from state to state Please note that in the European Union you as a consumer might have other legal rights under national legislation of European Union Member States governing the sale of Altec Lansing s goods Those rights are not affected by this guarantee The above limited warranties and remedies are sole warranties and remedies available to purchaser if and to the extent valid and enforceable under the applicable law DISPOSAL OF OLD ELECTRICAL AND ELECTRONIC EQUIPMENT This symbol on the product or o
26. the 7 band graphic EQ Power on off button Volume increase button Track forward button Play pause button FM preset buttons Clip On Remote Features Play pause a song on your iPhone or iPod n iPod mode press the tii button to begin playing a selected track Press the button again o pause it Tune radio stations n FM mode use the 4 or iis buttons See the Listening to the Radio section for additional information Seek radio stations tt button See the Listening to the Radio section for n FM mode press and hold the is additional information Store a radio station n FM mode tune to the station you d like to store and then press and hold one of he PRESET buttons P1 P2 P3 or P4 See the Listening to the Radio section for more information Select a preset radio station n FM mode press the PRESET button P1 P2 P3 or P4 that corresponds to the station you d like to hear See the Listening to the Radio section for more information NOTE For best results aim the clip on remote toward the Mix speaker system 10 Dock your iPhone or iPod in the Altec Lansing Mix speaker system Make sure the correct adapter for iPhone or iPod is inserted in the speaker system s dock Slide the guard down to protect the iPhone or iPod I Lone WO I iS U Select iPod mode Press the SOURCE button on your speaker system or clip on remote until
27. wall outlet or the connector isn t plugged into the power supply jack on the back of the Speaker system Plug the AC adapter into a wall outlet and plug the connector into the power supply jack on the back of the speaker system Wall outlet is not functioning Plug another device into the same outlet to confirm the outlet is working The batteries are dead Replace with new batteries See the Getting Started section for details The power isn t turned on Using the wrong adapter for iPhone or iPod or no adapter Turn on the speaker system by pressing the D button The LCD display turns on Make sure the adapter is the proper fit for your iPhone or iPod iPhone or iPod didn t install properly Remove your iPhone or iPod from the dock and check for obstruction on the connectors in the dock and on your iPhone or iPod Then reseat it in the dock and slide the guard down to protect it Troubleshooting Symptom Possible Problem Solution iPhone or iPod doesn t respond to the speaker system iPhone or iPod is not installed properly Remove your iPhone or iPod from the dock and check for obstructions on the connectors in the dock and on your iPhone or iPod Then reseat it in the dock and slide the guard down to protect it Your iPhone or iPod software is too old Upgrade software on your iPhone or iPod For details visit www apple com ipod download iPhone or iPod is locked up Pleas
Download Pdf Manuals
Related Search