TP-LINK TL-SG1008D network switch
Contents
1. measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment CE Mark Warning CE This is a class B product In a domestic environment this product mav cause radio interference in which case the user may be required to take adequate measures Safety Notices AN Cautions Do not use this product near water for example in a wet basement or near a swimming pool Avoid using this product during an electrical storm There may be a remote risk of electric shock from lightning Package Contents The following items should be found in vour package gt One TL SG1005D TL SG1008D Switch gt One Power Adapter gt This User Guide Note The wall mounting screws are not provided with our product Please contact your distributor if any of the listed items are damaged2. TP LINK User Guide TL SG1005D TL SG1008D 5 8 Port Gigabit Desktop Switch Rev 2 0 2 7106503707 COPYRIGHT amp TRADEMARKS Specifications are subject to change without notice TP UINIK is a registered trademark of TP LINK TECHNOLOGIES CO LTD Other brands and product names are trademarks or registered trademarks of their respective holders No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation transformation or adaptation without permission from TP LINK TECHNOLOGIES CO LTD Copyright 2011 TP LINK TECHNOLOGIES CO LTD All rights reserved http www tp link com FCC STATEMENT FC This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following
3. h port can be used as general ports or Uplink ports and any port can be simply plugged into a server a hub a router a switch or a PC using the straight cable or crossover cable Diagnostic LEDs which display link status and activity allowing you to quickly detect and correct problems on the network The TL SG1005D TL SG1008D switch adopts Green Ethernet technology supports power saving features The switch automatically powers down the ports that have no link or are connected to the computers which have been shut down budgets power output for different Ethernet cable lengths 1 2 Features gt Supports Green Ethernet technology to implement power saving features Complies with IEEE802 3 IEEE802 3u IEEE802 3ab standards 5 8 10 100 1000Mbps Auto Sensing RJ45 ports supporting Auto MDI MDIX Supports IEEE802 3x flow control for Full duplex Mode and backpressure for Half duplex Mode Non blocking switching architecture that forwards and filters packets at full wire speed for maximum throughput 4K entry MAC address table of TL SG1005D TL SG1008D with auto learning and auto aging Supports for Jumbo frames of up to 9KB LED indicators for monitoring power link speed and activity External power adapter supply Chapter 2 Identifying External Components This Chapter describes the front panel and rear panel of the Switch 2 1 Front Panel Figure 2 1 TL SG1008D Switch Front Panel 3 The Switch s LEDs are located o
4. n the front panel gt Power LED This indicator will light up when the Switch powers up gt LEDs 1 8 The LED indicates Link Active status The corresponding LED indicator will light solid green when connected to a network device It flashes green when data is being transmitted or received on the working connection Note The LEDs description above explains the device s working status after initialization 2 2 Rear Panel POWER 8 1 6 5 4 3 2 1 Figure 2 2 TL SG1008D Switch Rear Panel The following parts are located on the rear panel gt POWER The POWER socket is where you will connect the power adapter Please use the power adapter provided with this TL SG1008D Switch gt Port 1 8 The TL SG1008D Switch is equipped with 8 10 100 1000Mbps Auto Sensing RJ45 ports where you will connect your network devices The working status can be indicated by the corresponding LEDs on the front panel Chapter 3 Installation The Switch can be either located on a desktop or mounted on a wall 3 1 Mounting the Switch on a Desk To locate the Switch on a desktop please follow these steps 1 Place the Switch on a flat desk 2 Inspect the Power Adapter carefully and make sure that it is properly connected to a power source 3 Ensure adequate ventilation space around the switch for dissipating heat and air No
5. or missing Convention The Switch or TL SG1005D TL SG1008D mentioned in this User Guide stands for TL SG1005D TL SG1008D 5 8 port Gigabit Desktop Switch without any explanation Note The two devices of TL SG1005D and TL SG1008D are sharing this User Guide For simplicity we will take TL SG1008D for example throughout this Guide The differences between them are gt TL SG1005D Switch with 5 10 100 1000Mbps_ Auto Negotiation RJ45 ports gt IL SG1008D Switch with 8 10 100 1000Mbps_ Auto Negotiation RJ45 ports Chapter 1 Introduction of the Product Thank you for choosing the TL SG1005D TL SG1008D 5 8 port Gigabit Desktop Switch 1 1 Overview of the Product Powered by the Gigabit Ethernet Technology TL SG1005D TL SG1008D Gigabit Desktop Switch provides the seamless network connection which can speed up your old network to 1000Mbps ensuring the graphics CGI CAD or multimedia files and other applications with bandwidth intensive files transferred across the network almost instantly The non blocking switching architecture adopted in the TL SG1005D TL SG1008D switch greatly improves network response times as well as significantly speed up the traffic between subnets by forwarding and filtering packets at full wire speed for maximum throughput The TL SG1005D TL SG1008D switch is plug and play In addition the Auto MDI MDIX cable detection on all ports eliminates the demand of crossover cable or Uplink port Eac
6. r Rate Fast Ethernet 100Mbps Half Duplex 200Mbps Full Duplex Gigabit Ethernet 2000Mbps Full Duplex 10Base T UTP category 3 4 5 cable maximum 100m EIA TIA 568 100Q STP maximum 100m 100Base TX UTP category 5 5e cable Network Media Cable maximum 100m EIA TIA 568 100Q STP maximum 100m 1000Base T UTP category 5 cable maximum 100m EIA TIA 568 1000 STP maximum 100m 5 8 10 100 1000Mbps_ Auto Negotiation RJ45 ports MAC Address Learning 1000Base T 1488000pps Port Number of Ports 10Base T 14880pps Port Frame Forward Rate 100Base Tx 148800pps Port 1000Base T 1488000pps Port Environmental and Physical Operating Temperature 0 40 C 32 104 F Storage Temperature 40 70 C 40 158T Operating Humidity 10 90 non condensing Storage Humidity 5 90 non condensing Appendix B Troubleshooting 1 The Power LED is not lit Check to see if the AC power cord is connected to the Switch properly and make sure the power source is ON 2 The Link Act LED is not lit when a device is connected to the corresponding port Check to see if the cable connectors are firmly plugged into the Switch and the device and verify the connected device is turned on and working well Make sure the cable is not longer than 100 meters 328 feet
7. te Please avoid any heavy thing placed on the switch To ensure the stable cable connection please keep the switch horizontal on the desktop with white cover facing up 3 2 Mounting the Switch on a Wall There are two wall mounting slots on the bottom panel of the Switch To mount the Switch on a wall please follow the steps below 1 Drill two holes into the wall Insert a screw into each hole and leave a part of its head exposed 2 Place the two wall mounting slots over the screws and slide the Switch down to fasten it bottom of the Switch O O KA r r N eo es H AY H TEANS IN H ID i Le NIL NL kW ie Ww kL L 129 61mm 3 3 Power On Power on the Switch and it will automatically initialize and its LED indicators will respond as follows Name Time Status Indication scora on Off Power on LEDs port No device connected to the 1 8 corresponding port rd 3 second There is a 10 100 1000Mbps device connected to the corresponding port Note If the LED indicators don t respond as described above please check the power supply and its connection Appendix A Specifications General Standards IEEE802 3 IEEE802 3u IEEE802 3ab Protocol CSMA CD Ethernet 10Mbps Half Duplex 20Mbps Full Duplex Data Transfe
Download Pdf Manuals
Related Search