Home

Zonet ZSR4124WE router

1. Spanning Tree or set it to Disabled DHCP Server If you want to activate DHCP server function of this router select Enabled or set it to Disabled 34 Recommended Value if you don t know what to fill IP Address 192 168 2 1 Subnet Mask 255 255 255 0 802 1d Spanning Tree Disabled DHCP Server Enabled 2 6 2 DHCP Server oO oO N z yet One week 192 168 2 240 192 168 2 245 These settings are only available when DHCP Server in LAN IP section is Enabled and here are descriptions of every setup items Lease Time Please choose a lease time the duration that every computer can keep a specific IP address of every IP address assigned by this router from dropdown menu Start IP Please input the start IP address of the IP range End IP Please input the end IP address of the IP range Domain Name If you wish you can also optionally input the domain name for your network This is optional Recommended Value if you don t know what to fill Lease Time Two Weeks or Forever if you have less than 20 computers Start IP 192 168 2 100 End IP 192 168 2 200 Domain Name leave it blank The number of the last field mentioned d field of End IP must be greater than Start IP and can not the same with router s IP address The former three fields of IP address of Start IP
2. Current Virtual Server Table DESEA Enable Virtual Server Check this box to enable virtual server and uncheck this box to disable virtual server Private IP Input the IP address of the computer which provides Internet service Computer Name Pull down the menu and all the computers connected to the router will be listed here You can easily to select the computer name without checking the IP address of the computer Private Port Input the port number of the IP address which provides 61 Internet service Type Select the type of connection TCP or UDP If you re not sure please select Both Public Port Please select the port number of Internet IP address which will be redirected to the port number of local IP address defined above Comment Please input any text to describe this mapping up to 16 alphanumerical characters Add Add the mapping to virtual server table Reset Remove all inputted values Virtual Server Table All existing virtual server mappings will be displayed here Delete Selected Please select a virtual server mapping by clicking the Select box of the mapping then click Delete Selected button to remove the mapping If there is no existing mapping this button will be grayed out Delete All Delete all mappings existed in virtual server table Reset Unselect all mappings After you finish with all settings please click Apply button and the
3. IP address Please input IP address assigned by your service provider Service Provider assigned by your service provider Subnet Mask Please input subnet mask assigned by your service provider DNS address Please input the IP address of DNS server provided by your service provider Service Provider Please input the IP address of DNS server Gateway Address provided by your service provider You must use the addresses provided by your Internet service provider wrong setting value will cause connection problem When you finish with all settings press OK if you want to go back to previous menu click Back NOTE You can choose this Internet connection method if your service provider assigns a fixed IP address also know as static address to you and not using DHCP or PPPoE protocol Please contact your service provider for further information 15 2 3 3 Setup procedure for PPPoE xDSL PPPoE Enter the User Name and Password required by your ISP in the appropriate fields If your ISP has provided you with a Service Name enter it in the Service Name field otherwise leave it blank User Name Password Service Name eS 1392 612 lt MTU Value lt 1492 nT CLET Connect on Demand CEELEN E 10 1 1000minutes User Name Please input user name assigned by your Internet service provider here Password Please input t
4. 3 4 6 Statistics 78 You can use this function to check the statistics of wireless LAN and WAN interface of this router Please click Statistics menu on the left of web management interface and the following message will be displayed on your web browser You can click Refresh button to display latest information 3 5 Configuration Backup and Restore You can backup all configurations of this router to a file so you can make several copied of router configuration for security reason To backup or restore router configuration please follow the following instructions Please click Tool located at the upper right corner of web management interface then click Configuration Tools on the left of web management interface then the following message will be displayed on your web browser Backup Settings Restore Settings A estore Settings TE Restore to Factory Default Backup Settings Press Save button and you ll be prompted to Browse download the configuration as a file default filename is config bin you can save it as another filename for different versions and keep it in a safe place Restore Settings Press Browse to pick a previously saved configuration file from your computer and then click Upload to transfer the configuration file to router After the configuration is uploaded the router s configuration will be replaced by the file you jus
5. After you finish the wireless setting please click Apply button after you click Apply the following message will be displayed on your web browser Please click Continue to back to previous setup menu to continue on router setup or click Apply to reboot the router so the settings will take effect Please wait for about 30 seconds while router is rebooting 44 2 7 2 Advanced Wireless Settings This router provides some advanced control of wireless parameters if you want to configure these settings please click Wireless menu on the left of web management interface then click Advanced Settings and the following message will be displayed on your web browser ermine 2546 256 2346 CIRA LICOCA 2347 0 2347 BLETE IGAEL 100 20 1024 ms DTIM Period 3 1 10 Data Rate Auto Rem t ce Auto v UTTUTR GUR Auto 20 40 MHZ 20 MHZ AGUIRI Short Preamble Long Preamble eee Enable Disable acm O Auto Always None Tx Power 100 Enable Disable Fragment Threshold Set the Fragment threshold of wireless radio Do not modify default value if you don t know what it is default value is 2346 RTS Threshold Set the RTS threshold of wireless radio Do not modify default value if you don t know what it is default value is 2347 Beacon Interval Set the beacon interval of wireless radio Do no
6. Idle Time Out If you have selected the connection type to Connect On Demand please input the idle time out After you finish with all settings please click Apply button and the following message will be displayed on your web browser Please click Continue to back to previous setup menu to continue on other setup 27 procedures or click Apply to reboot the router so the settings will take effect Please wait for about 30 seconds while router is rebooting If you want to reset all settings in this page back to previously saved value please click Cancel button 2 5 4 Setup procedure for PPTP PPTP requires two kinds of setting WAN interface setting setup IP address and PPTP setting PPTP user name and password Here we start from WAN interface setting e WAN Interface Settings Obtain an IP address automatically ed MAC address 000000000000 Clone Mac address Use the following IP address fp Paddes Subnet Mask Default Gateway Select the type of how you obtain IP address from your service provider here You can choose Obtain an IP address automatically equal to DHCP please refer to Cable Modem section above or Use the following IP address i e static IP address WAN interface settings must be correctly set or the Internet connection will fail even those settings of PPTP settings are correct Please contact your Int
7. Internet Connection menu on the left of web management interface and the following message will be displayed on your web browser Pee a CCIE Fixed IP connect eC it 192 168 1 10 Tate 255 255 255 0 TET aera 192 160 1254 iter Gite 00 0E 2E 44 6B 02 LUED ALEE 192 168 0 2 Terie AL EE 0 0 0 0 This information will vary depending on the connection status 3 4 3 Device Status You can use this function to know the status of your router 76 Please click Device Status menu on the left of web management interface and the following message will be displayed on your web browser Wireless Configuration Mode AP ESSID default Channel Number 1 Security WEP IP Address 192 168 2 1 Subnet Mask 255 255 255 0 DHCP Server Disable MAC Address 00 0e 2e 44 6b 01 This information will vary depending on the device status 3 4 4 System Log All important system events are logged You can use this function to check the event log of your router Please click System Log menu on the left of web management interface and the following message will be displayed on your web browser Jan 3 08 24 41 none syslog info syslogd started BusyBox v1 00 pre2 200 A m gt Save Save current event log to a text file Clear Delete all event logs displayed here Refresh Refresh the event log display 77 3 4 5 Security Log All information about network and system security is kept here and you c
8. 802 11n Wireless Broadband Router USER MANUAL Table of Content Chapter Introduction 4 4 ccscucicncie natin navnnaincnnbainncendaisnciandamnniie 1 1 1 Introduction and safety information 0 0 cs sssecsesseessesssesecseessecsecnecseeneaneeneenes 1 1 2 Safety Information cscs ccc ceeded cc chet cane elcditcnnesdaesecicvndebcbelasebeacunedideedtt 2 1 3 System Requirements 6 saduda cuca datacutodatndasadduadeuaddunamonumanint 2 Hath Pakage Contents necnscaiiin a AAAA aa 2 1 5 Familiar with your new wireless broadband router sssssssssssseesssssssssseeese 2 Chapter Il System and Network Setup essssesssssssesssssserssssseerossscerosssseresssseeeossseerossseeressss 4 2 1 Build network cONNECHION fii chondmaddunddaGuiansuandaanadodeaaanionsuods 4 2 2 Connect to wireless broadband router by web browser sssssssssseessssssssse 5 2 3 Using Quick S t p encoiesciieinnienieieiaa iiaii 11 2 4 BAS C SetU ciii i A aE ERRER heel ae esa ee cee en La lode 21 2 5 Setup Internet Connection WAN Setup sessssesssssseessssseerssssseresssseresssseeesssseee 24 2 7 Wireless LAN Configuration ssssssssseeessssssssseseeessssssssseeteesssssssseeeresssssssseeereesssssss 37 Chapter Il Advanced Functions uu ecesssssssssssscsecscssssscssesccsccscsecsecsecsccsccscscsecaeeaeeeceseesenees 55 3 1 Quality of Service QOS ssessssssseesssssssssseeeesssssssssseesssssssssseee
9. AP Bridge WDS Connect this router with up to four WDS capable wireless routers to expand the scope of network Universal Repeater The router can act as Station and AP at the same time It can use Station function to connect to a Root AP and use AP function to service all wireless stations within its coverage NOTE For AP Bridge Point to Point and AP Bridge Point to Multi Point mode wireless router is operated in wireless bridge dedicated mode wireless router is only used to expand the scope of network and no wireless clients will be accepted If you want to use your wireless router to expand the scope of network and also accept wireless clients please select AP Bridge WDS or Universal Repeater mode 2 7 1 1 Setup procedure for AP Please select the radio band you want to use from Band dropdown menu and the following message will be displayed 38 AP v 2 4 GHz B G N default Channel Number 1 Associated Clients Show Active Clients Band Please select the radio band from one of following options m 2 4 GHz band only allows 802 11b wireless network client to connect this router maximum transfer rate 11Mbps m 2 4 GHz N band only allows 802 11n wireless network client to connect this router maximum transfer rate 150Mbps m 2 4 GHz B G band only allows 802 11b and 802 11g wireless network client to connect this router
10. Static IP here If you select Dynamic IP you have to select an Internet connection session from dropdown menu if you select Static IP please input the IP 74 address that you want to map to a specific private IP address Client PC IP address Please input the private IP address that the Internet IP address will be mapped to Computer Name Pull down the menu and all the computers connected to the router will be listed here You can easily to select the computer name without checking the IP address of the computer Add Click Add button to add the public IP address and associated private IP address to the DMZ table Reset Click Clear to remove the value you inputted in Public IP address and Client PC IP address field Current DMZ table All existing public IP address and private IP address mapping will be displayed here Delete Selected If you want to delete a specific DMZ entry check the select box of the DMZ entry you want to delete then click Delete Selected button You can select more than one DMZ entries Delete All If you want to delete all DMZ entries listed here please click Delete All button Reset You can also click Reset button to unselect all DMZ entries After you finish with all settings please click Apply button and the following message will be displayed on your web browser Please click Continue to back to previous setup menu to
11. Access Control This function allows or denies computers with specific MAC address from connecting to the network it can also allow or deny computers with specific IP address protocol or port Please click Firewall menu on the left of web management interface then click Access Control and the following message will be displayed on your web browser CI Enable MAC Filtering Deny Allow Select x ETTER abla ee eee eet eats rece Fro compuername cient Pc mac adores Comment select Client PC Client PC i 7 olemejesme orense fc pen tonar seee Add PC Enable MAC Filtering Check this box to enable MAC address based filtering and please select Deny or Allow to decide the behavior of MAC filtering table If you select deny all MAC addresses listed in filtering table will be denied from connecting to the network if you select allow only MAC addresses listed in filtering table will be able to connect to the network and rejecting all other network devices Client PC MAC address Please input the MAC address of computer or network device here dash or colon are not required i e If the MAC address label of your wireless device indicates aa bb cc dd ee ff or aa bb cc dd ee ff just input aabbccddeeff Computer Name Pull down the menu and all the computers connected the router will be listed here You can easily to se
12. Site Survey When you use this wireless router as a wireless station for Ethernet network device to have wireless capability you have to associate it with a working access point Click Select Site Survey button then a Wireless Site Survey Table will pop up It will list all available access points near by You can select one access point in the table and it will join wireless LAN through this access point WLAN MAC For some applications you may need to designate a specific MAC address for the router Please enter the MAC address here If you are connecting the router to a computer you can simply press Clone Mac address button to fill the MAC address field with the MAC address of your computer 2 7 1 3 Setup procedure for AP Bridge Point to Point In this mode you can connect your wireless router with another to combine two access points and expand the scope of wireless network and all clients wired only AP will not accept wireless clients in this mode of two wireless routers will think they re on the same physical network This function is very convenient when you need to connect two networks between two buildings Here are instructions about how to connect two wireless routers together AP Bridge Point to Point vj BELCH 2 4 GHz B G N R Channel Number Uae CIGA 000000000000 NOTE Two wireless routers must use the same mode band channel number and security set
13. menu described in chapter 2 3 However you can setup WAN connections up by using WAN configuration menu You can also set advanced functions like DDNS Dynamic DNS here To start configuration please follow the following instructions Please click WAN menu on the left of web management interface and the following message will be displayed on your web browser 24 Please select an Internet connection method depend on the type of connection you re using You can either click the connection method on the left or right If you select the connection method on the right please click More Configuration button after a method is selected WAN Settings System 4 WAN The Broadband router can be connected to your Service Provider through the following methods Dynamic IP Obtains an IP Address automatically from your Service Provider Uses a Static IP Address Your Service Provider gives a Static IP Static IP Address to access Internet services O PPPoE PPP over Ethernet is a common connection method used in xDSL connections Point to Point Tunneling Protocol is a common connection method O PPTP used in xDSL connections e LAN O L2TP Layer Two Tunneling Protocol is a common connection method used Wireless in xDSL connections QoS Telstra Big Pond Telstra Big Pond is a Internet service is provided in Australia NAT Firewall More Configuration 2 5 1 Setup procedure for Dynamic IP D
14. 6 ALG Settings Application Layer Gateway ALG is a special function of this router It includes many preset routing rules for numerous applications which require special support With these supports those applications which required special support will be able to work with NAT architecture Please click NAT menu on the left of web management interface then click ALG Settings and the following message will be displayed on your web browser A Amanda Support for Amanda backup tool protocol Egg Support for eggdrop bot networks FTP Support for FTP H323 Support for H323 netmeeting IRC bia to work though NAT and connection MMS eal for Microsoft Streaming Media Services Quake3 Support for Quake Ill Arena connection tracking and nat Talk Allows netfilter to track talk connections TFTP Support for TFTP IPsec Support for IPsec passthrough CJ Starcraft Support for Starcraft Battle net game protocol E MSN Support for MSN file tranfer There are many applications listed here Please check the box of the special 65 support for applications you need and then click Apply button and the following message will be displayed on your web browser Please click Continue to back to previous setup menu to continue on other setup procedures or click Apply to reboot the router so the settings will take effect Please wait for about 30 seconds while router is rebooting If you want to reset all settings in
15. Filtering Table All existing IP addresses in filtering table will be listed here Add PC Click this button to add a new IP address to IP filtering table up to 20 IP addresses can be added Delete Selected If you want to delete a specific IP address entry check the select box of the IP address you want to delete then click Delete Selected button You can select more than one IP addresses Delete All If you want to delete all IP addresses listed here please click Delete All button After you finish with all settings please click Apply button and the following message will be displayed on your web browser Please click Continue to back to previous setup menu to continue on other setup procedures or click Apply to reboot the router so the settings will take effect Please wait for about 30 seconds while router is rebooting If you want to reset all settings in this page back to previously saved value please click Cancel button 68 3 3 1 1 Add PC After button is clicked the following message will be displayed on your web browser Client PC Description cc Protocol Port Range i A PC Service Both HTTP TCP Port 80 3128 8000 8080 8081 O E mail Sending SMTP TCP Port 25 C News Forums NNTP TCP Port 119 Ci E mail Receiving POPS TCP Port 110 C Secure HTTP HTTPS TCP Por 443 O File Transfer FIP TCP Port 21 a M
16. However it s still useful to remember the channel number you use some wireless client supports manual channel number select and this would help in certain scenario when there is some radio communication problem Associated Clients Click Show Active Clients button then an Active Wireless Client Table will pop up You can see the status of all active wireless stations that are connecting to the access point NOTE If you don t have special reason to limit the type of allowed wireless client it s recommended to choose 2 4 GHz B G N to maximize wireless client compatibility TIPS You can try to change channel number to another one if you think the data transfer rate is too slow There could be some other wireless routers using the same channel which will disturb the radio communication between wireless client and the wireless router 2 7 1 2 Setup procedure for Station Infrastructure In this mode you can connect the router to Ethernet device such us TV Game player HDD amp DVD to enable the Ethernet device be a wireless station and join to a wireless network through an access point or AP router Station Infrastructure v 2 4 GHz B G N default Select Site Survey WLAN tes OO0000000000 Clone MAC Band Select the band you want to use 40 ESSID This is the name of wireless network You can type the SSID of the network you would like to connect here
17. all settings please click Apply button and the following message will be displayed on your web browser Please click Continue to back to previous setup menu to continue on other setup procedures or click Apply to reboot the router so the settings will take effect Please wait for about 30 seconds while router is rebooting If you want to reset all settings in this page back to previously saved value please click Cancel button 3 3 3 1 DoS Advanced Settings When you click Advanced button in DoS menu the following message will be displayed on your web browser Denial of Service Feature E Ping of Death Packet S Per 5econ Burst E Discard Ping From WAN E Port Scan NMAP FIN URG PSH Xmas tree Another Xmas tree Null scan SYN RST SYN FIN SYN only unreachable port Ping of Death Set the threshold of when this DoS prevention mechanism will be activated Please check the box of Ping of Death and input the frequency of threshold how many packets per second minute or hour you can also input the Burst value which means when this number of Ping of Death packet is received in very short time this DoS prevention mechanism will be activated Discard Ping From WAN Check the box to activate this DoS prevention mechanism Port Scan Many kind of port scan methods are listed here please check one or more DoS attack methods you want to prevent Sync Flood Like P
18. following message will be displayed on your web browser Please click Continue to back to previous setup menu to continue on other setup procedures or click Apply to reboot the router so the settings will take effect Please wait for about 30 seconds while router is rebooting If you want to reset all settings in this page back to previously saved value please click Cancel button 3 2 4 Port Mapping for Special Applications Some applications require more than one connection a time these applications won t work with simple NAT rules In order to make these applications work you can use this function to let these applications work 62 a Enable IP Address TCP Port to Open UDP Port to Open 0 0 0 0 Iks Select x Popular Applications Select Game x E Current Trigger Port Table NO Computer name IP Address TCP Port to Open UDP Port to Open Comment Select Enable Check this box to enable special applications and uncheck this box to disable virtual server IP Address Input the IP address of the computer which you want to open the ports Computer Name Pull down the menu and all the computers connected to the router will be listed here You can easily to select the computer name without checking the IP address of the computer TCP Port to Open This is the out going Outbound range of TCP port numbers for this particular application UDP Port to Op
19. management interface and the following message will be displayed on your web browser Enable QoS Total Download Bandwidth 0 kbits Total Upload Bandwidth kbits peua ODE Yap DUET teseeeneeseeseeeeeseeeenseeeenseeeenseeeenseenensnenensnenenay Download FTP Download Apply Cancel Enable QoS Check this box to enable QoS function unselect this box if you don t want to enforce QoS bandwidth limitations Total Download Bandwidth You can set the limit of total download bandwidth in kbits To disable download bandwidth limitation input 0 here Total Upload Bandwidth You can set the limit of total upload Band width in kbits To disable upload bandwidth limitation input O here 55 Current QoS Table All existing QoS rules will be displayed here Add Click add button to add a new QoS rule see section 3 1 2 Add a new QoS rule below Edit If you want to modify the content of a specific rule please check the select box of the rule you want to edit then click Edit button Only one rule should be selected a time If you didn t select a rule before clicking Edit button you ll be prompted to add a new rule Delete Selected You can delete selected rules by clicking this button You can select one or more rules to delete by check the select the box of the rule s you want to delete a time If the QoS table is empty this button will be grayed out and can
20. maximum transfer rate 11Mbps for 802 11b clients and maximum 54Mbps for 802 11g clients m 2 4 GHz G band only allows 802 11g wireless network client to connect this router maximum transfer rate 54Mbps m 2 4 GHz B G N 2 4GHz band allows 802 11b 802 11g and 802 11n wireless network client to connect this router maximum transfer rate 11Mbps for 802 11b clients maximum 54Mbps for 802 11g clients and maximum 150Mbps for 802 11n clients m For 802 11b and 802 11g mode the signals can be transmitted only by antenna 1 The antenna in the right side of the rear panel m For 802 11n mode The router is operating in a 1T2R Spatial Multiplexing MIMO configuration 1 antenna is for signal transmitting and 2 antennas are for signal receiving ESSID This is the name of wireless router You can type any alphanumerical characters here maximum 32 characters ESSID is used to identify your own wireless router from others when there are other wireless routers in the same area Default SSID is default it s recommended to change default ESSID value to the one which is meaningful to you like my home office_room1 etc Channel Number Please select a channel from the dropdown list of Channel Number available channel numbers are 1 to 13 for European countries 1 to 11 for USA You can choose any channel number you want to use and almost all wireless clients can locate the channel you re using automatically without any problem
21. providers use DHCP Dynamic Host Configuration 13 Protocol to assign IP address to you In this case you can choose Cable Modem as Internet connection type even you re using another connection type like xDSL Also some cable modem uses PPPoE so you can choose PPPoE xDSL for such cable modem connection even you re using a cable modem 2 3 1 Setup procedure for Cable Modem Cable Modem UET LIES OOOOOO000000 Clone Mac address Host Name Please input the host name of your computer this is optional and only required if your service provider asks you to do so MAC address Please input MAC address of your computer here if your service provider only permits computer with certain MAC address to access internet If you re using the computer which used to connect to Internet via cable modem you can simply press Clone Mac address button to fill the MAC address field with the MAC address of your computer After you finish with all settings please click OK button if you want to go back to previous menu click Back 14 2 3 2 Setup procedure for Fixed IP xDSL Fixed IP xDSL Enter the IP Address Subnet Mask Gateway IP Address and DNS IP Address provided to you by your ISP in the appropriate fields IP address assigned by your Service Provider 172 1 1 1 ST gue em 255 255 0 0 DNS address Te emer me Cree 172 1 1 254
22. recognized by the Internet which must be assigned by InterNIC TCP IP UDP Transmission Control Protocol Internet Protocol TCP IP and Unreliable Datagram Protocol UDP TCP IP is the standard protocol for data transmission over the Internet Both TCP and UDP are transport layer protocol TCP performs proper error detection and error recovery and thus is reliable UDP on the other hand is not reliable They both run on top of the IP Internet Protocol a network layer protocol WAN Wide Area Network A network that connects computers located in geographically separate areas e g different buildings cities countries The Internet is a wide area network Web based management Graphical User Interface GUI Many devices support a graphical user interface that is based on the web browser This means the user can use the familiar Netscape or Microsoft Internet Explorer to Control configure or monitor the device being managed 87
23. this page back to previously saved value please click Cancel button 3 3 Firewall Excepting NAT this router also provides firewall function to block malicious intruders from accessing your computers on local network These functions include inbound attack prevention and block outbound traffics like block URLs which have pre defined keywords Please follow the following instructions to enable or disable firewall function Please click Firewall menu on the left of web management interface and the following message will be displayed on your web browser Security Settings Firewall The Broadband router provides extensive firewall protection by restricting connection parameters thus limiting the risk of hacker attack and defending against a wide array of common attacks However for applications that require unrestricted access to the Internet you can configure a specific client server as a Demilitarized Zone DMZ Enable or disable Firewall module function Enable Disable Apply Please select Enable or Disable to enable or disable firewall function of this router the click Apply button and the following message will be displayed on your web browser Please click Continue to back to previous setup menu to continue on other setup procedures or click Apply to reboot the router so the settings will take effect Please wait for about 30 seconds while router is rebooting 66 3 3 1
24. to configure your computer to use dynamic IP address 2 2 1 Windows 2000 IP address setup 1 Click Start button it should be located at lower left corner of your computer then click control panel Double click Network and Dial up Connections icon click Local Area Connection and Local Area Connection Properties window will appear Select Internet Protocol TCP IP and then click Properties Local Area Connection Properties 3 2 x General Connect using BY Realtek RTL8029 4S PCI Ethernet Adapter Components checked are used by this connection E Cligntator bienssote Matworks war ile and Printer Sharing for Migosoft Networks Internet Protocol TCP IP A S80 NI gii aie Install Uninstall k Properties Gore pe m Description L T he Transmission Control Protocol Internet Protocol The default wide area network protocol that provides communication across diverse interconnected networks qi MV Show icon in taskbar when connected OK Cancel 2 Select Obtain an IP address automatically and Obtain DNS server address automatically then click OK 2 2 2 Windows XP IP address setup 1 Click Start button it should be located at lower left corner of your computer then click control panel Double click Network and Internet Connections icon click Network Connections then double click Local Area Connection Local Ar
25. will be displayed on your web browser Please click Continue to back to previous setup menu to continue on other setup procedures or click Apply to reboot the router so the settings will take effect Please wait for about 30 seconds while the router is rebooting If you want to reset all settings in this page back to previously saved value please click Cancel button 3 2 5 UPnP Setting This function enables network auto configuration for peer to peer communications with this function network devices will be able to communicate with other devices directly and learn about information about other devices Many network device and applications rely on UPnP function nowadays Please click NAT menu on the left of web management interface then click UPnP and the following message will be displayed on your web browser MATT O Enable Disable There is only one option in this page please select Enable or Disable to 64 enable or disable UPnP function then click Apply button and the following message will be displayed on your web browser Please click Continue to back to previous setup menu to continue on other setup procedures or click Apply to reboot the router so the settings will take effect Please wait for about 30 seconds while router is rebooting If you want to reset all settings in this page back to previously saved value please click Cancel button 3 2
26. 0 seconds while router is rebooting If you want to reset all settings in this page back to previously saved value please click Cancel button 2 6 Wired LAN Configuration Before all computers using wired Ethernet connection i e those computers connect to this router s LAN port 1 to 4 by Ethernet cable can communicate with each other and access internet they must have a valid IP address There are two ways to assign IP addresses to computers static IP address set the IP address for every computer manually and dynamic IP address IP address of computers will be assigned by router automatically It s recommended for most of computers to use dynamic IP address it will save a lot of time on setting IP addresses for every computer especially when there are a lot of computers in your network for servers and network devices which will provide services to other computer and users that come from Internet static IP address should be used so other computes can locate the server Suggestions on IP address numbering plan If you have no idea on how to define an IP address plan for your network here are some suggestions 1 A valid IP address has 4 fields a b c d for most of home and 33 company users it s suggested to use 192 168 c d where c is an integer between 0 and 254 and d is an integer between 1 and 254 This router is capable to work with up to 253 clients so you can set d field of IP address of router a
27. 00000 It means the device s network address is 11011001 10110000 10010000 00000000 and its host ID is 00000000 00000000 00000000 00000111 This is a convenient and efficient method for routers to route IP packets to their destination ISP Gateway Address see ISP for definition The ISP Gateway Address is an IP address for the Internet router located at the ISP s office ISP Internet Service Provider An ISP is a business that provides connectivity to the Internet for individuals and other businesses or organizations 85 LAN Local Area Network A LAN is a group of computers and devices connected together in a relatively small area Such as a house or an office Your home network is considered a LAN MAC Address MAC stands for Media Access Control A MAC address is the hardware address of a device connected to a network The MAC address is a unique identifier for a device with an Ethernet interface It is comprised of two parts 3 bytes of data that corresponds to the Manufacturer ID unique for each manufacturer plus 3 bytes that are often used as the product s serial number NAT Network Address Translation This process allows all of the computers on your home network to use one IP address Using the broadband router s NAT capability you can access the Internet from any computer on your home network without having to purchase more IP addresses from your ISP Port Network Clients LAN PC uses port number
28. 1 browser Please select time zone at Set time zone drop down list and input the IP address or host name of time server If you want to enable daylight savings setting please check Enable Function box and set the duration of daylight setting When you finish click Apply You ll see the following message displayed on web browser Press Continue to save the settings made and back to web management interface press Apply to save the settings made and restart the router so the settings will take effect after it reboots NOTE You can refer to the instructions given in last chapter Using Quick Setup for detailed descriptions on time zone settings 2 4 2 Change management password Default password of this router is 1234 and it s displayed on the login prompt when accessed from web browser There s a security risk if you don t change the default password since everyone can see it This is very important when you have wireless function enabled To change password please follow the following instructions Please click System menu on the left of web management interface then click Password Settings and the following message will be displayed on your web browser Confirmed Password Current Password Please input current password here New Password Please input new password here Confirmed Password Please input new password here again When you fin
29. 2 11b g Draft N wireless enabled network devices including PDA cellular phone game console and more can connect to this wireless router without additional cabling The MIMO technology also gives you the highest speed of wireless experience ever With a compatible wireless card installed in your PC you can transfer file for up to 150Mbps transfer data rate The radio coverage is also doubled so don t worry if your office or house is really big Other features of this router including High Internet Access throughput Allow multiple users to share a single Internet line Supports up to 253 users Share a single Cable or xDSL internet connection Access private LAN servers from the internet Four wired LAN ports 10 100M and one WAN port 10 100M Work with IEEE 802 11b g Draft N wireless LAN devices Support DHCP Server Client for easy IP address setup Support multiple wireless modes like AP Station Infrastructure Wireless Bridge and Universal Repeater Advanced network and security features like Special Applications QoS DMZ Virtual Servers Access Control Firewall Allow you to monitor the router s status like DHCP Client Log System Log Security Log and Device Connection Status Easy to use Web based GUI for network configuration and management purposes Remote management function allows configuration and upgrades from a remote computer over the Internet Auto MDI MDI X function for all wired Ethernet
30. 3 Using Quick Setup This router provides a Quick Setup procedure which will help you to 11 complete all required settings you need to access the Internet in very short time Please follow the following instructions to complete the Quick Setup Please go to QuickSetup menu by clicking QuickSetup button Wireless Router Microsoft Internet Explorer File Edit Yiew Favorites Tools Help set x a A JO search 5 Favorites amp B 33 Address http 192 168 2 1findex asp Broadband Router Home General Setup Status Tool Quick Setup Wizard QuickSetup The Quick Setup Wizard provides only the necessary configurations to connect your Broadband router to your Internet Service Provider ISP through an external cable or a DSL modem General Setup The Broadband router supports advanced functions like Virtual Server Access Control Hacker Attack Detection and DMZ We highly recommend you keep the default settings F Staus Ji Status Information The Broadband router s status information provides the following information about your Broadband router Hardware Firmware version Serial Number and its current operating status Tools Broadband router Tools Tools include Configuration tools Firmware upgrade and Reset Configuration tools allow you to Backup Restore or Restore to Factory Default setting for your Broadband router The Firmware upgrade tool allows you to upgrade your
31. Broadband router s firrewara Tha DESET tanl allawe wan ta rocot vour Rroadhand rotor Internet And the following message will be displayed 1 Set Time Zone GMT 06 00 Central Time US amp Canada v EEA CCIC 192 43 244 18 Enable Function Daylight Savi Set Time Zone Please press button a drop down list will be shown and you can choose a time zone of the location you live Time Server Address Input the IP address host name of time server here Daylight Savings If the country you live uses daylight saving please check Enable Function box and choose the duration of daylight saving After you finish with all settings please click Apply button NOTE There are several time servers available on internet 129 6 15 28 time a nist gov 132 163 4 101 time a timefreq bldrdoc gov 131 107 1 10 time nw nist gov If you found that the time of router is incorrect try another time server 2 Broadband Type Broadband Type Specify the WAN connection type required by your Internet Service Provider Specify a Cable modem Fixed IP xDSL PPPoE xDSL or PPTP xDSL connection Cable Modem A connection through a cable modem requires minimal configuration When you set up an account with your Cable provider the Cable provider and your Broadband router will automatically establish a connection so you probably do not need to enter anything more O Fixed IP xDSL Some xDSL I
32. DNS access failures the secondary DNS will be used Has your Internet service provider given you a DNS address REE Clete 192 168 0 2 Secondary DNS Address optional DNS Address Please input the IP address of DNS server provided by your service provider Secondary DNS Address Please input the IP address of another DNS server provided by your service provider this is optional NOTE Only IP address can be entered here DO NOT use the hostname of DNS server i e only numeric characters and dots are accepted 31 1020 3040 ronan a Correct CNS SErViCEPrOVIGEN COM c cccecssesstsesssteesssseesessesssrn na Incorrect After you finish with all settings please click Apply button and the following message will be displayed on your web browser Please click Continue to back to previous setup menu to continue on other setup procedures or click Apply to reboot the router so the settings will take effect Please wait for about 30 seconds while router is rebooting If you want to reset all settings in this page back to previously saved value please click Cancel button 2 5 8 Setup procedure for DDNS DDNS Dynamic DNS is an IP to Hostname mapping service for those Internet users who don t have a static fixed IP address It will be a problem when such user wants to provide services to other users on Internet because their IP address will vary every time when connected to
33. End IP and IP Address of LAN IP section mentioned a b and c field should be the same These settings will affect wireless clients too 35 2 6 3 Static DHCP Leases Table This function allows you to assign a static IP address to a specific computer forever so you don t have to set the IP address for a computer and still enjoy the benefit of using DHCP server Maximum 16 static IP addresses can be assigned here If you set Lease Time to forever in DHCP Server section you can also assign an IP address to a specific computer permanently however you will not be able to assign a certain IP address to a specific computer since IP addresses will be assigned in random order by this way Enable Static DHCP Leases MAC address IP address New 001122334455 192 168 2 100 Enable Static DHCP Leases Check this box to enable this function otherwise uncheck it to disable this function MAC Address Input the MAC address of the computer or network device total 12 characters with character from 0 to 9 and from a to f like O01122aabbcc IP address Input the IP address you want to assign to this computer or network device Add After you inputted MAC address and IP address pair click this button to add the pair to static DHCP leases table If you want to remove all characters you just entered click Clear After you clicked Add the
34. Internet and other user will not be able to know the IP address they re using a certain time This router supports DDNS service of several service providers for example DynDNS http www dyndns org TZO http www tzo com Please go to one of DDNS service provider s webpage listed above and get a free DDNS account by the instructions given on their webpage DDNS 2 DDNS allows users to map the static domain name to a dynamic IP address You must get a account password and your static domain name from the DDNS service providers Our products have DDNS support for www dyndns org and www tzo com now Provider OTE O Enabled Disabled Account E Mail Password Key Apply Cancel 32 Dynamic DNS If you want to enable DDNS function please select Enabled otherwise please select Disabled Provider Select your DDNS service provider here Domain Name Input the domain name you ve obtained from DDNS service provider Account E Mail Input account or email of DDNS registration Password Key Input DDNS service password or key After you finish with all settings please click Apply button and the following message will be displayed on your web browser Please click Continue to back to previous setup menu to continue on other setup procedures or click Apply to reboot the router so the settings will take effect Please wait for about 3
35. MAC address and IP address mapping will be added to Static DHCP Leases Table section e Static DHCP Leases Table It allows to entry 16 sets address only Po macadres IP adire Soleat 1 00 1 1 22 33 44 55 192 168 2 100 O If you want to delete a specific item please check the Select box of a MAC address and IP address mapping then click Delete Selected button 36 if you want to delete all mappings click Delete All If you want to deselect all mappings click Reset After you finish all LAN settings please click Apply button on the bottom of this page After you click Apply the following message will be displayed on your web browser Please click Continue to back to previous setup menu to continue on router setup or click Apply to reboot the router so the settings will take effect Please wait for about 30 seconds while router is rebooting 2 7 Wireless LAN Configuration If your computer PDA game console or other network devices which is equipped with wireless network interface you can use the wireless function of this router to let them connect to Internet and share resources with other computers with wired LAN connection You can also use the built in security functions to protect your network from being intruded by malicious intruders Please follow the following instructions to set wireless parameters Please click Wireless menu on the left of web managem
36. S and generate a set of passphrase key for WPS connection Passphrase Key The wireless security key of the router will be displayed here 53 Config Mode There are Registrar and Enrollee modes for the WPS connection When Registrar is enabled the wireless clients will follow the router s wireless settings for WPS connection When Enrolle mode is enabled the router will follow the wireless settings of wireless client for WPS connection Configure via Push Button Click Start PBC to start Push Button style WPS setup procedure This wireless router will wait for WPS requests from wireless clients for 2 minutes The WLAN LED on the wireless router will be steady on for 2 minutes when this wireless router is waiting for incoming WPS request Configure Please input the PIN code of the wireless client you via client wish to connect and click Start PIN button PinCode The WLAN LED on the wireless router will be steady on when this wireless router is waiting for incoming WPS request 2 7 6 Security Tips for Wireless Network Here are some quick tips to help you improve the security level of your wireless network Never use simple words like school apple and computer as WEP encryption or WPA passphrase A complicated the combination of number alphabet even symbol and long enough WEP key and WPA passphrase is much safer than simple and short ones Remember that the wireless
37. S Some examples of WEP key Don t use those examples use the one of your own ASCII 5 characters pilot phone 23561 2Hyux xmL ASCII 13 characters digital FAMILY 82Jh26xHy3m amp n Hex 10 characters 287d2aa732 1152dabc85 Hex 26 characters 9284bcda8427c9e036f7abcd84 To improve security level do not use those words which can be found in a dictionary or too easy to remember pilot and phone listed above 48 are bad examples just intended to show you how a WEP key look like Wireless clients will remember the WEP key so you only have to input the WEP key on wireless client once and it s worth to use complicated WEP key to improve security level After you finish WEP setting please click Apply button and the following message will be displayed on your web browser Please click Continue to back to previous setup menu to continue on other setup procedures or click Apply to reboot the router so the settings will take effect Please wait for about 30 seconds while router is rebooting 2 7 3 3 Wi Fi Protected Access WPA When you select this mode the wireless router will use WPA encryption and the following setup menu will be shown on your web browser a WPA pre shared key x WPACTKIP OWPAQ AES OWPAZ Mixed a WPA Unicast Cipher Suite Please select a type of WPA cipher suite Available options are WPA TKIP WPA2 AES and WPA2 Mixed You can
38. SN Messenger TCP Port 1863 C t Telnet Service TCP Port 23 Oo AIM AOL Instant Messenger TCP Port 5190 Ci NetMeeting H 323 TCP Port 389 522 1503 1720 1731 O DNS UDP Port 53 Oo SNMP UDP Port 161 162 O VPN PPTP TCP Port 1723 O VPN L2TP UDP Port 1701 B TCP All TCP Port C UDP All UDP Port a User Define Service a Client PC Description Please input any text to describe this IP address up to 16 alphanumerical characters Client PC IP address Please input the starting IP address in the left field and input the end IP address in the right field to define a range of IP addresses or just input the IP address in the left field to define a single IP address Client PC Service Please check all services you want to allow or deny 69 this IP address to use you can check multiple services Protocol If the service you need is not listed above you can create a new service on your own Please select TCP or UDP if you re not sure please select Both Port Range Please input the port range of new service here If you want to specify port 80 to 90 please input 80 90 if you want to apply this rule on a single port just input the port number like 80 Add When you finish with all settings please click Add to save settings you ll be brought back to previous menu and the rule you just set will appear in current IP filtering table If you want to remove all settings in this page c
39. Selected Delete All All Reset BEB BBE ERR EER REPRE Enable Wireless Access Control Apply Cancel Delete Selected If you want to delete a specific MAC address entry check the select box of the MAC address you want to delete then click Delete Selected button You can select more than one MAC addresses Delete All If you want to delete all MAC addresses listed here please click Delete All button Reset You can also click Reset button to unselect all MAC addresses Enable Wireless Access Control To enforce MAC address filtering you have to check Enable Wireless Access Control When this item is unchecked wireless router will not enforce MAC address filtering of wireless clients MAC Address Input the MAC address of your wireless devices here dash or colon are not required i e If the MAC address label of your wireless device indicates aa bb cc dd ee ff or aa bb cc dd ee ff just input aabbccddeeff Comment You can input any text here as the comment of this MAC address like ROOM 2A Computer or anything You can input up to 16 alphanumerical characters here This is optional and you can leave it blank however it s recommended to use this field to write a comment for every MAC addresses as a memory aid Add Click Add button to add the MAC address and associated comment to the MAC address filtering table Clear Click Clear to rem
40. Setup procedure for L2TP e L2TP Settings Password L2TP Gateway CUUR 1392 512 lt MTU Value lt 1492 Tm eee Continuous b f Idle Time Out 1 1000 minutes User ID Please input user ID user name assigned by your Internet service provider here Password Please input the password assigned by your Internet service provider here L2TP Gateway Please input the IP address of PPTP gateway assigned by your Internet service provider here MTU Please input the MTU value of your network connection here If you don t know you can use default value Connection type Please select the connection type of Internet connection you wish to use please refer to section 2 5 3 for detailed descriptions Idle Time Out Please input the idle time out of Internet connection you wish to use and refer to section 2 5 3 for detailed descriptions When you finish with all settings please click OK if you want to go back to previous menu click Back 2 5 6 Setup procedure for Telstra Big Pond Telstra Big Pond Australia Only lf your Internet service is provided by Telstra Big Pond in Australia you will need to enter your information below This information is provided by Teistra BigPond User Name Password C User decide login server manually 7 30 This setting only works when you re using Telstra big pond s netw
41. TU value of your network connection here If you don t know you can use default value BEZEQ ISRAEL Setting item BEZEQ ISRAEL is only required to Check if you re using the service provided by BEZEQ network in Israel Connection type Please select the connection type of Internet connection you wish to use please refer to last section for detailed descriptions Idle Time Out Please input the idle time out of Internet connection you wish to use and refer to last section for detailed descriptions When you finish with all settings please click OK If you want to go back to previous menu click Back 2 3 5 Setup procedure for L2TP xDSL L2TP is another popular connection method for xDSL and other Internet connection types and all required setting items are the same with PPTP connection 18 Like PPTP there are two kinds of required setting we ll start from WAN Interface Settings e WAN Interface Settings Obtain an IP address automatically Host Name Ue rrr 000000000000 Clone Mac address Use the following IP address IP address Subnet Mask Default Gateway 0 0 0 Please select the type of how you obtain IP address from your service provider here You can choose Obtain an IP address automatically equal to DHCP please refer to Cable Modem section above or Use the following IP address equal to static IP address please refer
42. ailable options are None SMTP HTTP POP3 and FTP You can select a specific traffic type for this rule if you want to make this rule as a IP address based rule apply the limitation on all traffics from to the specified IP address port number select None Protocol Please select the protocol type of this rule available options are TCP and UDP If you don t know what protocol your application uses please try TCP first and switch to UDP if this rule doesn t seems to work After you finish with all settings please click save button you ll be brought back to previous menu and the rule you just set will appear in current QoS table if you did anything wrong you ll get an error message when you click Save button please correct your input by the instructions given by the error message If you want to erase all values you just entered Click Reset 3 2 Network Address Translation NAT Network address translations solve the problem if sharing a single IP address to multiple computers Without NAT all computers must be assigned with a valid Internet IP address to get connected to Internet but Internet service providers only provide very few IP addresses to every user Therefore it s necessary to use NAT technology to share a single Internet IP address to multiple computers on local network so everyone can get connected to Internet 3 2 1 Basic NAT Settings Enable or disable NAT functio
43. an use this function to check the security event log of your router Please click Security Log menu on the left of web management interface and the following message will be displayed on your web browser 2000 01 01 00 00 08 start Static IP ad 2000 01 01 00 00 09 SNTP connect to TimeServer 192 43 244 18 2000 01 01 00 00 09 FIREWALL WAN IP is 192 168 1 10 setting firewall 2000 01 01 00 00 19 SNTP connect fail 7 2000 01 01 00 22 43 DNS dns restart 2000 01 01 00 22 48 start Static IP 2000 01 01 00 22 49 SNTP connect to TimeServer 192 43 244 18 2000 01 01 00 22 49 FIREWALL WAN IP is 192 166 1 10 setting firewall 2000 01 01 00 22 59 SNTP connect fail lt i gt Save Save current event log to a text file K Clear Delete all event logs displayed here Refresh Refresh the event log display 3 4 5 Active DHCP client list If you are using the DHCP server function of this router you can use this function to check all active DHCP leases issued by this router Please click Active DHCP client menu on the left of web management interface and the following message will be displayed on your web browser IP Address MAC Address Time Expired s 192 168 2 240 00 10 60 db 52 9d 55 All information about active DHCP leases issued by this router will be displayed here You can click Refresh button to display latest information
44. between 1 and 65534 Enabled Select the field to start the configuration When you finish with all settings click Apply and you ll see the following message displayed on web browser Press Continue to save the settings made and back to web management interface press Apply to save the settings made and restart the router so the settings will take effect after it reboots NOTE When you want to manage this router from another computer on internet you have to input the IP address and port number of this router If your Internet service provider assigns you with a static IP address it will not be a problem but if the IP address your service provider assigns to you will vary every time you establish an internet connection this will be a problem Please either ask your service provider to give you a static IP address or use dynamic IP to host name mapping services like DDNS Please refer to chapter 2 5 8 DDNS client for details NOTE Default port number the web browser will use is 80 If the Port setting in this page is not 80 you have to assign the port number in the address bar of web browser manually For example if the IP address of this router is 1 2 3 4 and the port number you set is 8888 you have to input following address in the address bar of web browser http 1 2 3 4 8888 2 5 Setup Internet Connection WAN Setup Internet connections setup can be done by using Quick Setup
45. ced technician for help If you smell something strange or even see some smoke coming out from the router or power supply remove the power supply or switch the electrical power off immediately and call dealer of purchase for help 1 3 System Requirements Internet connection provided by xDSL or cable modem with a RJ 45 Ethernet port Computer or network devices with wired or wireless network interface card Web browser Microsoft Internet Explorer 4 0 or above Netscape Navigator 4 7 or above Opera web browser or Safari web browser An available AC power socket 100 240V 50 60Hz 1 4 Package Contents Before you starting to use this router please check if there s anything missing in the package and contact your dealer of purchase to claim for missing items One ZSR4124WE One Quick Installation Guide One CD with User Manual One AC Power Adapter 1 5 Familiar with your new wireless broadband router Front Panel Zonet 802 11n Wireless Broadband Router WAN i Ei 10 1 00M LNK ACT ZSR4124WE LED Name Light Status Description PWR On Router is switched on and correctly powered On Wireless WPS function is enabled N off Wireless network is switched off Flashing Wireless LAN activity transferring or receiving data WAR On WAN port Internet is running at 100Mbps 10 100M off WAN port Int
46. click Delete Selected button You can select more than one MAC addresses Delete All If you want to delete all URL Keyword listed here please click Delete All button Reset You can also click Reset button to unselect all URL Keywords After you finish with all settings please click Apply button and the following message will be displayed on your web browser Please click Continue to back to previous setup menu to continue on other setup procedures or click Apply to reboot the router so the settings will take effect Please wait for about 30 seconds while router is rebooting If you want to reset all settings in this page back to previously saved value please click Cancel button 3 3 3 DoS Attack Prevention Denial of Service DoS is a common attack measure by transmitting a great amount of data or request to your Internet IP address and server the Internet connection will become very slow and server may stop responding because it is not capable to handle too much traffics This router has a built in DoS attack prevention mechanism when you activate it the router will stop the DoS attack for you Please follow the 71 following instructions to set DoS prevention parameters Please click Firewall menu on the left of web management interface then click DoS and the following message will be displayed on your web browser Denial of Service Feature Ping of Dea
47. client is capable to keep the key or passphrase for you so you only have to input the complicated key or passphrase once It s not too trouble but will greatly improve security level You can hide the ESSID of this router by set Broadcast ESSID option to Disable Your wireless router will not be found by other people in proximity if they re just using the AP scanning function of their wireless client and this can reduce the chance of being intruded Use Access Control function described in section 2 7 4 so those people who are not in your list will not be able to connect to your network 54 Chapter III Advanced Functions 3 1 Quality of Service QoS Quality of service provides an efficient way for computers on the network to share the internet bandwidth with a promised quality of internet service Without QoS all computers and devices on the network will compete with each other to get internet bandwidth and some applications which require guaranteed bandwidth like video streaming and network telephone will be affected therefore an unpleasing result will occur like the interruption of video audio transfer With this function you can limit the maximum bandwidth or give a guaranteed bandwidth for a specific computer to avoid said unpleasing result from happening 3 1 1 Basic QoS Settings Please follow the following instructions to set QoS parameters Please click Qos menu on the left of web
48. continue on other setup procedures or click Apply to reboot the router so the settings will take effect Please wait for about 30 seconds while router is rebooting If you want to reset all settings in this page back to previously saved value please click Cancel button 3 4 System Status The functions described here will provide you with system related information To enter system status menu please either click Status link located at the upper right corner of web management interface or click Status button in main menu 3 4 1 System information and firmware version You can use this function to know the system information and firmware version of this router Please click Status link located at the upper right 75 corner of web management interface and the following message will be displayed on your web browser Status and Information 2 You can use the Status page to monitor the connection status for the Broadband router s WAN LAN interfaces firmware and hardware version numbers any illegal attempts to access your network and information on all DHCP client PCs currently connected to your network System Model Wireless Router Uptime Oday Oh 36m 29s Hardware Version Rey A Boot Code Version 1 0 Runtime Code Version 1 04 NOTE Information displayed here may vary 3 4 2 Internet Connection Status You can use this function to know the status of current Internet connection Please click
49. ction specific DNS Suffix IP gt 192 168 2 3 255 255 255 0 gt 192 168 2 1 NOTE If the IP address of Gateway is not displayed or the address followed by IP Address begins with 169 please recheck network connection between your computer and router and or go to the beginning of this chapter to recheck every step of network setup procedure 3 Connect the router s management interface by web browser After your computer obtained an IP address from router please start your web browser and input the IP address of router in address bar The following message should be shown Connect to 192 168 2 1 Default admin 1234 User name E Password C Remember my password Please input user name and password in the field respectively default user name is admin and default password is 1234 then press OK button and you can see the web management interface of this router 10 Z Wireless Router Microsoft Internet Explorer File Edit View Favorites Tools Help set x a pe Search Je Favorites g B 3 Address g http 192 168 2 1findex asp Broadband Router Home General Setup Status Tool Quick Setup Wizard QuickSetup The Quick Setup Wizard provides only the necessary configurations to 5 connect your Broadband router to your Internet Service Provider ISP through an external cable or a DSL modem General Setup The Broadband router suppor
50. e Timeout is designed so that after there is no traffic to the Internet for a pre configured amount of time the connection will automatically be disconnected IP Address and Network Subnet Mask IP stands for Internet Protocol An IP address consists of a series of four numbers separated by periods which identifies a single unique Internet computer host in an IP network Example 192 168 2 1 It consists of 2 portions the IP network address and the host identifier The IP address is a 32 bit binary pattern which can be represented as four cascaded decimal numbers separated by aaa aaa aaa aaa where each aaa can be anything from 000 to 255 or as four cascaded binary numbers separated by bbbbbbbb bbbbbbbb bbbbbbbb bbbbbbbb where each b can either be 0 or 1 A network mask is also a 32 bit binary pattern and consists of consecutive leading 1 s followed by consecutive trailing 0 s such as 11111111 11111111 11111111 00000000 Therefore sometimes a network mask can also be described simply as x number of leading 1 s When both are represented side by side in their binary forms all bits in the IP address that correspond to 1 s in the network mask become part of the IP network address and the remaining bits correspond to the host ID For example if the IP address for a device is in its binary form 11011001 10110000 10010000 00000111 and if its network mask is 11111111 11111111 11110000 000
51. e of the wireless client you wish to connect to this wireless router The detailed instructions are listed follow Please click Wireless menu on the left of web management interface then click WPS and the following message will be displayed on your web browser 52 Enable WPS e Wi Fi Protected Setup Information Configured Self PinCode 44896643 default Authentication Mode WPA pre shared key Passphrase Key bash tebe e Device Configure Config Mode Configure via Push Button Start PBC Configure via Client PinCode cus Enable WPS Check this box to enable WPS function uncheck it to disable WPS Wi Fi Protected Setup Information WPS related system information will be displayed here WPS Status If the wireless security encryption function of this wireless router is properly set you ll see Configured message here If wireless security function has not been set you ll see unConfigured Self PIN code This is the WPS PIN code of this wireless router This code is useful when you need to build wireless connection by WPS with other WPS enabled wireless devices SSID The SSID of this wireless router will be displayed here Authentication Mode The wireless security authentication mode of this wireless router will be displayed here If you don t enable security function of the wireless router before WPS is activated the router will auto set the security to WPA AE
52. ea Connection Status window will appear and then click Properties 4 Local Area Connection Properties General Authentication Advanced Connect using E AMD PCNET Family PCI Ethernet Ad This connection uses the following items v E Client for Microsoft Networks amp File and BsinbeeSbaung for Microsoft Networks UB thoS Packet Scheduler oes e Internet Protocol TCP IP Ks o Pr yyy eat P e Properties 8 s A Description ORR Transmission Control Protocol Intemet Protocol The default wide area network protocol that provides communication across diverse interconnected networks C Show icon in notification area when connected Notify me when this connection has limited or no connectivity 2 Select Obtain an IP address automatically and Obtain DNS server address automatically then click OK 2 2 3 Windows Vista IP address setup 1 Click Start button it should be located at lower left corner of your computer then click control panel Click View Network Status and Tasks and then click Manage Network Connections Right click Local Area Network then select Properties Local Area Connection Properties window will appear select Internet Protocol Version 4 TCP IPv4 and then click Properties E Intel R PRO 1000 MT Network Connection This connection uses the following items V 0 Client for Microsoft N
53. eessssssssseessessssssseeeseesssssss 55 3 2 Network Address Translation NAT ssssesssssessssssssssseeesssssssssseeesssssssssseeeseessssss 58 3 3 Firewall inire iaieiaiia ti Ea a canna EAEE E i 66 3 4 System Stat Sissis a a a 75 3 5 Configuration Backup and Restore sssssssssseesssssssssseeeresssssssseeesssssssssseeereesssssss 79 3 6 Firmware Upgrade sie desadutoautadetaduudaindueadutmdehadutuduadduanduds 80 3 7 System R S etn iie a EERE RERE R 80 Chapter IV AppendiX scscrcncucniceninnecncnnnnnnn 81 4 1 Hardware Specification eccesssssssssssscsecscsscssssscsccscssesecssesecsecscescsscseeseeseeuececeseseesee 81 4 2 TIOUDIESHOOLING unico suduaasnGadesuaniadaduauananduaaanannaaauaieddea 82 4 3 GLOSS ANY isinne asses ieaie cao nahn Binns A aa E ER 84 Chapter I Introduction 1 1 Introduction and safety information Thank you for purchasing this wireless broadband router This high cost efficiency router is the best choice for Small office Home office users all computers and network devices can share a single xDSL cable modem internet connection at high speed Easy install procedures allows any computer users to setup a network environment in very short time within minutes even inexperienced When the number of your computers and network enabled devices grow you can also expand the number of network slot by simple attach a hub or switch to extend the scope of your network All computers and IEEE 80
54. en This is the out going Outbound range of UDP port numbers for this particular application Comment The description of this setting Popula Applications This section lists the more popular applications that require multiple connections Select an application from the Popular Applications selection and click Add to save the setting to Current Trigger Port Table Add Add the setting to the Current Trigger Port Table Reset Click Reset will clear all above setting and you can set up again Current Trigger Port All the settings for the special applications will be listed here If you want to remove some Special Application settings from the Current Trigger Port Table select the Special Application settings you want to remove in the table and then click Delete Selected If you want remove all Special Appliacation settings from the table just click Delete All button Click Reset will clear your current selections Delete Selected Please select a special application by clicking the Select box of the mapping then click Delete Selected button to remove the setting If there s no setting here this button will be grayed 63 out Delete All Delete all settings existed in trigger port table Reset Unselect all settings Note Only one LAN client can use a particular special application at a time After you finish with all settings please click Apply button and the following message
55. ent interface and the following message will be displayed on your web browser You must enable wireless function of this router or the wireless interface of this router will not function Please select Enable then click Apply button If you re coming here because you want to disable wireless function please select Disable then click Apply button After you click Apply the following message will be displayed on your web browser Please click Continue to back to previous setup menu to continue on other setup procedures or click Apply to reboot the router so the settings will take effect Please wait for about 30 seconds while router is rebooting 2 7 1 Basic Wireless Settings Please click Wireless menu on the left of web management interface then click Basic Settings and the following message will be displayed on your 37 web browser 24 Ge BSH Y Channel Number v This wireless router can be work in 6 modes AP Standard wireless AP access point Station Infrastructure Configure the router to Ethernet device such us TV Game player HDD amp DVD to enable the Ethernet device be a wireless station AP Bridge Point to Point Connect this router with another wireless router to expand the scope of network AP Bridge Point to Multi Point Connect this router with up to four other wireless routers to expand the scope of network
56. ernet is running at 10Mbps Flashing WAN activity transferring or receiving data On WAN port is connected WAN off WAN port is not connected LNK ACT Flashing WAN activity transferring or receiving data LAN On LAN port is running at 100Mbps 10 100M off LAN port is running at 10Mbps LAN On LAN port is connected Off LAN port is not connected LNK ACT Flashing LAN activity transferring or receiving data Back Panel Antenna A Antenna B Power Reset WPS Lre Item Name Description Antenna A B These antennas are 3dBi dipole antennas Power Power connector connects to A C power adapter Reset WPS Reset the router to factory default settings clear all settings or start WPS function Press this button and hold for 10 seconds to restore all settings to factory defaults and press this button for less than 5 seconds to start WPS function 1 4 Local Area Network LAN ports 1 to 4 WAN Wide Area Network WAN Internet port Chapter II System and Network Setup 2 1 Build network connection Please follow the following instruction to build the network connection between your new WIRELESS router and your computers network devices 1 Connect your xDSL cable modem to the WAN port of router by Ethernet cable ADSL or a Cable Modem 2 Connect all
57. ernet service provider if you don t know what you should fill in these fields Now please go to PPTP settings section 28 e PPTP Settings Password Umer Cee 0 0 0 0 Connection ID Optional 1392 612 lt MTU Value lt 1492 GIZAL EE Enable for BEZEQ network in ISRAEL use only Connection Type Continuous vi onner iscont Feat 0 1 1000minutes MTU User ID Please input user ID user name assigned by your Internet service provider here Password Please input the password assigned by your Internet service provider here PPTP Gateway Please input the IP address of PPTP gateway assigned by your Internet service provider here Connection ID Please input the connection ID here this is optional and you can leave it blank MTU Please input the MTU value of your network connection here If you don t know you can use default value BEZEQ ISRAEL If you are connecting to the BEZEQ network in Israel Please enable this function Connection type Please select the connection type of Internet connection you wish to use please refer to section 2 5 3 for detailed descriptions Idle Time Out Please input the idle time out of Internet connection you wish to use and refer to section 2 5 3 for detailed descriptions When you finish with all settings please click OK if you want to go back to previous menu click Back 29 2 5 5
58. etworks V E QoS Packet Scheduler V E File and Printer Sharing for Microsoft Networks F Sa Sages cee Transmission Control Protocol Intemet Protocol The default wide area network protocol that provides communication across diverse interconnected networks 2 Select Obtain an IP address automatically and Obtain DNS server address automatically then click OK 2 2 4 Router IP address lookup After the IP address setup is complete please click start gt run at the bottom lower corner of your desktop home user ba Internet a My Documents 5 Internet Explorer lt 4 My Recent Documents 3 E mail Fe M Outlook Express pr O My Pictures Windows Media Player A Set Program Access and Defaults 33 Windows Messenger ka Printers and Faxes Tour Windows xP Help and Support Files and Settings Transfer pP Search Wizard All Programs gt P Log Off 0 Turn Off Computer Type the name of a program Folder document or Internet resource and Windows will open it for you cmd Cancel Browse Input ipconfig then press Enter key Please check the IP address followed by Default Gateway In this example the IP address of router is 192 168 2 1 please note that this value may be different et C WINDOWS system32 cmd exe iC gt ipconf ig Windows IP Configuration Ethernet adapter Local Area Connection Conne
59. for help The date and time of all a Adjust the internal clock of router event logs are wrong 4 3 Glossary Default Gateway Router Every non router IP device needs to configure a default gateway s IP address When the device sends out an IP packet if the destination is not on the same network the device has to send the packet to its default gateway which will then send it out towards the destination DHCP Dynamic Host Configuration Protocol This protocol automatically gives every computer on your home network an IP address DNS Server IP Address DNS stands for Domain Name System which allows Internet servers to have a domain name such as www Broadbandrouter com and one or more IP addresses such as 192 34 45 8 A DNS server keeps a database of Internet servers and their respective domain names and IP addresses so that when a domain name is requested as in typing Broadbandrouter com into your Internet browser the user is sent to the proper IP address The DNS server IP address used by the computers on your home network is the location of the DNS server your ISP has assigned to you DSL Modem DSL stands for Digital Subscriber Line A DSL modem uses your existing phone lines to transmit data at high speeds Ethernet A standard for computer networks Ethernet networks are connected by special cables and hubs and move data around at up to 10 100 million bits per second Mbps 84 idle Timeout Idl
60. g Pond in Australia you will need to enter your information below This information is provided by Teistra BigPond a Password O User decide login server manually This setting only works when you re using Telstra big pond s network service in Australia You need to input User Name Please input the user name assigned by Telstra Password Please input the password assigned by Telstra User device login server manually Check this box to choose login by yourself Login Server Please input the IP address of login server here When you finish with all settings click OK if you want to go back to previous menu click Back When all settings are finished you ll see the following message displayed on your web browser Please click Apply button to prepare to restart the 20 router and you ll see a message Please wait for about 30 seconds then click OK button You ll be back to router management interface again and the router is ready with new settings 2 4 Basic Setup In this chapter you ll know how to change the time zone password and remote management settings Please start your web browser and log onto router web management interface then click General Setup button on the left or click General Setup link at the upper right corner of web management interface Wireless Router Microsoft Internet Explorer File Edit View Favorite
61. he password assigned by your Internet service provider here Service Name Please give a name to this Internet service this is optional MTU Please input the MTU value of your network connection here If you don t know you can use default value Connection Type Please select the connection type of Internet connection you wish to use detailed explanation listed below Idle Time Out Please input idle time out detailed explanation listed below When you finish with all settings please click OK if you want to go back to previous menu click Back m MTU Please use default value if you don t know what it is or ask your service provider for a proper value m Connection Type There are 3 options Continuous keep internet connection alive do not disconnect connect on Demand only connects to Internet when there s a connect attempt and Manual only connects to Internet when Connect button on this page is pressed and disconnects when Disconnect button is pressed m Idle Time Out Specify the time to shutdown internet connect after no 16 internet activity is detected by minute This option is only available when connection type is Connect on Demand 2 3 4 Setup procedure for PPTP xDSL PPTP xDSL requires two kinds of setting WAN interface setting setup IP address and PPTP setting PPTP user name and password Here we start from WAN interface setting e WAN I
62. ing of Death you can set the threshold of when this 73 DoS prevention mechanism will be activated After you finish with all settings please click Apply button and the following message will be displayed on your web browser Please click Continue to back to previous setup menu to continue on other setup procedures or click Apply to reboot the router so the settings will take effect Please wait for about 30 seconds while router is rebooting If you want to reset all settings in this page back to previously saved value please click Cancel button 3 3 4 Demilitarized Zone DMZ Demilitarized Zone DMZ refers to a special area in your local network This area resides in local network and all computers in this area uses private IP address too But these private IP addresses are mapped to a certain Internet IP address so other people on Internet can fully access those computers in DMZ Please follow the following instructions to set DMZ parameters Please click Firewall menu on the left of web management interface then click DMZ and the following message will be displayed on your web browser CI Enable DMZ Public IP address Client PC IP address Dynamic IP Session1 v O a IP S i LL ee w Current DMZ Table Enable DMZ Check this box to enable DMZ function uncheck this box to disable DMZ function Public IP address You can select Dynamic IP or
63. ish click Apply If you want to keep original password unchanged click Cancel If the current and new passwords are correctly entered after you click Apply you ll be prompted to input your new password 22 Connect to 192 168 2 1 Default admin 1234 User name Password C Remember my password Please use new password to enter web management interface again and you should be able to login with new password 2 4 3 Remote Management This router does not allow management access from Internet to prevent possible security risks especially when you defined a weak password or didn t change default password However you can still management this router from a specific IP address by enabling the Remote Management Function To do so please follow the following instructions Please click System menu on the left of web management interface then click Remote Management and the following message will be displayed on your web browser o Apply Host Address Input the IP address of the remote host you wish to initiate a management access Port You can define the port number this router should expect an incoming request If you re providing a web service default port number is 80 you should try to use other port number You can use the 23 default port setting 8080 or something like 32245 or 1429 Any integer
64. lect the computer name without checking the IP address of the computer Comment You can input any text here as the comment of this MAC address like ROOM 2A Computer or anything You can input up to 16 67 alphanumerical characters here This is optional and you can leave it blank however it s recommended to use this field to write a comment for every MAC addresses as a memory aid Add Click Add button to add the MAC address and associated comment to the MAC address filtering table Reset Remove all inputted values MAC Filtering Table All existing MAC addresses in filtering table will be listed here Delete Selected If you want to delete a specific MAC address entry check the select box of the MAC address you want to delete then click Delete Selected button You can select more than one MAC addresses Delete All If you want to delete all MAC addresses listed here please click Delete All button Reset You can also click Reset button to unselect all MAC addresses Enable IP Check this box to enable IP address based Filtering Table filtering and please select Deny or Allow to decide the behavior of IP filtering table If you select deny all IP addresses listed in filtering table will be denied from connecting to the network if you select allow only IP addresses listed in filtering table will be able to connect to the network and rejecting all other network devices IP
65. lick Reset button 3 3 2 URL Blocking If you want to prevent computers in local network from accessing certain website like pornography violence or anything you want to block you can use this function to stop computers in local network from accessing the site you defined here This function is useful for parents and company managers Please follow the following instructions to set URL blocking parameters Please click Firewall menu on the left of web management interface then click URL Blocking and the following message will be displayed on your web browser C Enable URL Blocking FunuKeyword Current URL Blocking Table PoP UtLRayword Select 1 waw playboy com O 70 Enable URL Blocking Check this box to enforce URL Blocking uncheck it to disable URL Blocking URL Keyword Input the URL host name or IP address of website like http www blocked site com or http 11 22 33 44 or the keyword which is contained in URL like pornography cartoon stock or anything Add Click Add button to add the URL keyword to the URL Keyword filtering table Reset Click Reset to remove the value you inputted in URL Keyword field Current URL Blocking Table All existing URL Keywords in filtering table will be listed here Delete Selected If you want to delete a specific URL Keyword entry check the select box of the MAC address you want to delete then
66. ll accept wireless clients NOTE For WDS mode the output signal nature is the same as that of 42 normal AP mode 2 4 GHz B G N oo0000000000 ooo000000000 000000000000 EE e Band Select the band you want to use all the wireless routers must use the same setting ESSID Input the ESSID of your wireless router the setting should be the same with other wireless routers for the convenience of roaming Channel Number Select the channel you want to use all the wireless routers must use the same setting Associated Clients Click Show Active Clients button then an Active Wireless Client Table will pop up You can see the status of all active wireless stations that are connecting to the access point MAC address 1 to 4 Input the MAC address of other wireless routers Set Security Click to set security settings for this connection 2 7 1 6 Setup procedure for Universal Repeater In this mode the router can act as a wireless repeater it can be Station and AP at the same time It can use Station function to connect to a Root AP and use AP function to service all wireless stations within its coverage NOTE For Repeater Mode this router will demodulate the received signal checking if this signal is noise for the operating network then have the signal modulated and amplified again The output power of this mode is the same as that of WDS and normal AP mode 43 Universal Repeate
67. locate my router by my wireless client a Broadcast ESSID set to off b All three antennas are properly secured c Are you too far from your router Try to get closer d Please remember that you have to input ESSID on your wireless client manually if ESSID broadcast is disabled File download is very slow or breaks frequently a Are you using QoS function Try to disable it and try again b Internet is slow sometimes being patient c Try to reset the router and see if it s better after that d Try to know what computers do on your local network If someone s transferring big files other people will think Internet is really slow e If this never happens before call you Internet service provider to know if there is something wrong with their network I can t log onto web management interface password is wrong a Make sure you re connecting to the correct IP address of the router b Password is case sensitive Make sure the Caps Lock light is not illuminated c If you really forget the password do a hard 83 reset Router become hot a This is not a malfunction if you can keep your hand on the router s case b If you smell something wrong or see the smoke coming out from router or A C power adapter please disconnect the router and A C power adapter from utility power make sure it s safe before you re doing this and call your dealer of purchase
68. n Please click NAT menu on the left of web management interface and the following message will be displayed on your web browser 58 NAT Settings Network Address Translation NAT allows multiple users at your local site to access the Internet through a single Public IP Address or multiple Public IP Addresses NAT provides Firewall protection from hacker attacks and has the flexibility to allow you to map Private IP Addresses to Public IP Addresses for key services such as the Web or FTP Enable or disable NAT module function Enable Disable Apply To enable NAT function please select Enable for Enable NAT module function to disable please select Disable After you made the selection please click Apply button and the following message will be displayed on your web browser Please click Continue to back to previous setup menu to continue on other setup procedures or click Apply to reboot the router so the settings will take effect Please wait for about 30 seconds while router is rebooting 3 2 2 Port Forwarding This function allows you to redirect a single port or consecutive ports of Internet IP address to the same port of the IP address on local network The port number s of Internet IP address and private IP address the IP address on local network must be the same If the port number of Internet IP address and private IP address is different please use Virtual Server fu
69. nction described in next section Please click NAT menu on the left of web management interface then click Port Forwarding and the following message will be displayed on your web browser 59 CI Enable Port Forwarding lt lt Select Both v Current Port Forwarding Table Pno Computer name privater Type PortRange Comment selec Enable Port Forwarding Check this box to enable port mapping and uncheck this box to disable port mapping Private IP Input the IP address of the computer on local network which provides internet service Computer Name Pull down the menu and all the computers connected to the router will be listed here You can easily to select the computer name without checking the IP address of the computer Type Select the type of connection TCP or UDP If you re not sure please select Both Port Range Input the starting port number in the left field and input the ending port number in the right field If you only want to redirect a single port number just fill the port number in the left field Comment Please input any text to describe this mapping up to 16 alphanumerical characters e Add Add the mapping to port forwarding table Reset Remove all inputted values Port Forwarding Table All existing port forwarding mappings will be displayed here Delete Selected Please select a port forwarding mapping b
70. not be clicked Delete All By clicking this button you can delete all rules currently in the QoS table If the QoS table is empty this button will be grayed out and can not be clicked Move Up You can pull up the priority of the QoS rule you selected by clicking this button Move Down You can lower the priority of the QoS rule you selected by clicking this button Reset If you want to erase all values you just entered Click Reset After you finish with all settings please click Apply button and the following message will be displayed on your web browser Please click Continue to back to previous setup menu to continue on other setup procedures or click Apply to reboot the router so the settings will take effect Please wait for about 30 seconds while router is rebooting If you want to reset all settings in this page back to previously saved value please click Cancel button 3 1 2 Add a new QoS rule After you click Add button in QoS menu the following message will appear 56 Domisi a Jipe COO carrer es f fer Ponte Rule Name Please give a name to this QoS rule up to 15 alphanumerical characters Bandwidth Set the bandwidth limitation of this QoS rule You have to select the data direction of this rule Upload of Download and the speed of bandwidth limitation in Kbps then select the type of QoS guarantee guaranteed u
71. ns 2 7 3 1 Disable wireless security When you select this mode data encryption is disabled and every wireless device in proximity will be able to connect your wireless router if no other security measure is enabled like MAC address access control see section 2 7 4 or disable ESSID broadcast Only use this option when you really want to allow everyone to use your wireless router and you don t care if there s someone reads the data you transfer over network without your consent 2 7 3 2 WEP Wired Equivalent Privacy When you select this mode the wireless router will use WEP encryption and the following setup menu will be shown on your web browser E IRIE J Hex 10 characters com Encryption Key 2 fr oe Encryption Key 3 BARG Encryption Key 4 aeee CO Enable 802 1x Authentication Key Length There are two types of WEP key length 64 bit and 128 bit Using 128 bit is safer than 64 bit but will reduce some data transfer performance Key Format There are two types of key format ASCII and Hex When you select a key format the number of characters of key will be displayed For example if you select 64 bit as key length and Hex as key format you ll see the message at the right of Key Format is Hex 10 characters which means the length of WEP key is 10 characters Default Tx Key You can set
72. nterface Settings Obtain an IP address automatically ce M Tomomone JL Sore ec ates Use the following IP address lt 7 lt Select the type of how you obtain IP address from your service provider here You can choose Obtain an IP address automatically equal to DHCP please refer to Cable Modem section above or Use the following IP address i e static IP address WAN interface settings must be correctly set or the Internet connection will fail even those settings of PPTP settings are correct Please contact your Internet service provider if you don t know what you should fill in these fields Now please go to PPTP settings section 17 e PPTP Settings Password ee eet eee 0 0 0 0 Connection ID Optional RS 1392 612 lt MTU Value lt 1492 GIZAL EEL Enable for BEZEQ network in ISRAEL use only J i e T CLE T A Continuous Idle Time Out 1 1000minutes User ID Please input user ID user name assigned by your Internet service provider here Password Please input the password assigned by your Internet service provider here PPTP Gateway Please input the IP address of PPTP gateway assigned by your Internet service provider here Connection ID Please input the connection ID here this is optional and you can leave it blank MTU Please input the M
73. nternet Service Providers may assign a Fixed IP Address for your Broadband router If you have been provided with this information choose this option and enter the assigned IP Address Subnet Mask Gateway IP Address and DNS IP Address for your Broadband router PPPoE xDSL If you connect to the Internet using an xDSL Modem and your ISP has provided you with a Password and a Service Name then your ISP uses PPPoE to establish a connection You must choose this option and enter the required information PPTP xDSL If you connect to the Internet using an xDSL Modem and your ISP has provided you with a Password Local IP Address Remote IP Address and a Connection ID then your ISP uses PPTP to establish a connection You must choose this option and enter the required information L2TP xDSL Layer Two Tunneling Protocol is a common connection method used in xDSL connections Telstra Big Pond If your Internet service is provided by Telstra Big Pond in Australia you will need to enter your information below This information is provided by Teistra BigPond Please choose the broadband Internet connection type you re using in this page If you re not sure please contact your Internet service provider A wrong Internet connection type will cause connection problem and you will not be able to connect to internet If you want to go back to previous step please press Back button on the bottom of this page NOTE Some service
74. ork service in Australia You need to input User Name Please input the user name assigned by Telstra Password Please input the password assigned by Telstra User device login server manually Check this box to choose login server by yourself Login Server Please input the IP address of login server here When you finish with all settings click OK if you want to go back to previous menu click Back 2 5 7 Setup procedure for DNS If you select Dynamic IP or PPPoE as Internet connection method at least one DNS server IP address should be assigned automatically However if you have preferred DNS server or your service provider didn t assign the IP address of DNS server because of any reason you can input the IP address of DNS server here DNS 2 A Domain Name System DNS server is like an index of IP Addresses and Web Addresses If you type a Web address into your browser such as www broadbandrouter com a DNS server will find that name in its index and find the matching IP address Most ISPs provide a DNS server for speed and convenience Since your Service Provider may connect you to the Internet through dynamic IP settings it is likely that the DNS server IP Address is also provided dynamically However if there is a DNS server that you would rather use you need to specify the IP Address of that DNS server The primary DNS will be used for domain name access first in case the primary
75. ove the value you inputted in MAC address 51 and comment field After you finish with all settings please click Apply button and the following message will be displayed on your web browser Please click Continue to back to previous setup menu to continue on other setup procedures or click Apply to reboot the router so the settings will take effect Please wait for about 30 seconds while router is rebooting If you want to reset all settings in this page back to previously saved value please click Cancel button 2 7 5 Wi Fi Protected Setup WPS Wi Fi Protected Setup WPS is the simplest way to build connection between wireless network clients and this wireless router You don t have to select encryption mode and input a long encryption passphrase every time when you need to setup a wireless client you only have to press a button on wireless client and this wireless router and the WPS will do the rest for you This wireless router supports two types of WPS Push Button Configuration PBC and PIN code If you want to use PBC you have to push a specific button on the wireless client to start WPS mode and switch this wireless router to WPS mode too You can push Reset WPS button of this wireless router or click Start PBC button in the web configuration interface to do this if you want to use PIN code you have to know the PIN code of wireless client and switch it to WPS mode then provide the PIN cod
76. pgrade will fail and you may have to return this router to the dealer of purchase to ask for help Warranty voids if you interrupted the upgrade procedure 3 7 System Reset If you think the network performance is bad or you found the behavior of the router is strange you can perform a router reset sometime it will solve the problem To do so please click Tool located at the upper right corner of web management interface then click Reset on the left of web management interface then the following message will be displayed on your web browser Please click Apply to reset your router and it will be available again after few minutes please be patient 80 Chapter IV Appendix 4 1 Hardware Specification Model ZSR4124WE Protocols and Standards IEEE802 3 gt IEEE 802 3u gt IEEE 802 3x gt TCP IP gt UCP gt UDP gt PPPoE gt DHCP PPTP gt NAT NAPT gt UPnP gt DDNS gt IEEE 802 11n Draft 2 0 gt IEEE 802 11g IEEE 802 11b Flash 4 Mbytes NOR Flash System Memory 16 Mbytes SDRAM WAN 1 10 100M Auto MDI MDIX RJ45 port is LAN 4 10 100M Auto MDI MDIX RJ45 ports Frequency Band 2 412 2 4835GHz 802 11n up to 300 Mbps Data Transfer Rates 802 119 54 48 36 24 12 9 6Mbps 802 11b 11 5 5 2 1Mbps 11 Channels USA Canada Channel 13 Channels Europe 14 Channels Japan Extend Frequency DSSS Wireless Modulation DBPSK gt QPSK gt CCK and Paramete
77. ports 1 2 Safety Information In order to keep the safety of users and your properties please follow the following safety instructions This router is designed for indoor use only DO NOT place this router outdoor DO NOT put this router at or near hot or humid places like kitchen or bathroom Also do not left this router in the car in summer DO NOT pull any connected cable with force disconnect it from the router first If you want to place this router at high places or hang on the wall please make sure the router is firmly secured Falling from high places would damage the router and its accessories and warranty will be void Accessories of this router like antenna and power supply are danger to small children under 3 years old They may put the small parts in their nose or month and it could cause serious damage to them KEEP THIS ROUTER OUT THE REACH OF CHILDREN The router will become hot when being used for long time This is normal and is not a malfunction DO NOT put this router on paper cloth or other flammable materials There s no user serviceable part inside the router If you found that the router is not working properly please contact your dealer of purchase and ask for help DO NOT disassemble the router warranty will be void If the router falls into water when it s powered DO NOT use your hand to pick it up Switch the electrical power off before you do anything or contact an experien
78. pped You can enable the Connect on Demand option to automatically re establish the connection as soon as you attempt to access the Internet again If your Internet Service Provider requires the use of PPPoE enter the information below User Name Password Service Name LLURS 1392 612 lt MTU Value lt 1492 TC um hee Continuous i l Idle Time Out 1 1000minutes User Name Please input user name assigned by your Internet service provider here Password Please input the password assigned by your Internet service provider here Service Name Please give a name to this Internet service this is optional MTU Please input the MTU value of your network connection here If you don t know you can use default value Connection Type Please select the connection type of Internet connection you wish to use Continuous The connection will be kept always on If the connection is interrupted the router will re connect automatically Connect On Demand Only connect when you want to surf the Internet Idle Time Out is set to stop t he connection when the network traffic is not sending or receiving after an idle time Manual After you have selected this option you will see the Connect button and Disconnect button click Connect and the router will connect to the ISP If you want to stop the connection please click Disconnect button
79. r i 2 4 GHz B G N default k v Channel Number Associated Clients Show Active Clients Root AP SSID Select Site Survey Band Select the band you want to use all the wireless routers must use the same setting ESSID This is the name of wireless router You can type any alphanumerical characters here maximum 32 characters ESSID is used to identify your own wireless router from others when there are other wireless routers in the same area Default SSID is default it s recommended to change default ESSID value to the one which is meaningful to you like my home office_room1 etc Channel Number Select the channel you want to use all the wireless clients must use the same setting e Associated Clients Click Show Active Clients button then an Active Wireless Client Table will pop up You can see the status of all active wireless stations that are connecting to the access point Root AP SSID In Universal Repeater mode this device can act as a station to connect to a Root AP You should assign the SSID of the Root AP here or click Select Site Survey button to choose a Root AP Site Survey Click Select Site Survey button then a Wireless Site Survey Table will pop up It will list all available access points near by You can select one access point in the table and the router will join wireless LAN through this access point
80. rs OFDM BPSK QPSK 16 QAM 64 QAM Transmit output eae 54Mbps 1641dBm power 11Mbps 18 1dBm Transmission Indoor up to 50 70m Outdoor up to 100 160m Distance limited to environment RF Power 20dBm Antenna Gain 3dBi 2 Antenna type Fixed Omni directional Antenna Network Media 10Base T UTP category 3 or above cable 100Base TX UTP category 5 Media Access Protocol WMM Environment Operating Temperature 10 C 40 C Operating Humidity 10 90 non condensing Storage Temperature 20 C 70 C Storage Humidity 10 90 non condensing Power External power adapter output DC 12V 1 25A 81 4 2 Troubleshooting If you found the router is working improperly or stop responding to you don t panic Before you contact your dealer of purchase for help please read this troubleshooting first Some problems can be solved by you within very short time Scenario Solution Router is not a Please check the connection of power cord responding to me when and network cable of this router All cords and I want to access it by cables should be correctly and firmly inserted web browser to the router b If all LEDs on this router are off please check the status of A C power adapter and make sure it s correctly powered c You must use the same IP address section which router uses d Are you using MAC or IP address filter Try to connect the router by another comp
81. s 1 or 254 or any number between 1 and 254 and pick a number between 0 and 254 for field c 2 In most cases you should use 255 255 255 0 as subnet mask which allows up to 253 clients this also meets router s capability of working with up to 253 clients 3 For all servers and network devices which will provide services to other people like Internet service print service and file service they should use static IP address Give each of them a unique number between 1 and 253 and maintain a list so everyone can locate those servers easily 4 For computers which are not dedicated to provide specific service to others they should use dynamic IP address If you don t really understand the descriptions listed above don t worry We will provide recommended setup values below Please follow the following instructions to set wired LAN parameters Please click LAN menu on the left of web management interface there are three setup groups here LAN IP DHCP Server and Static DHCP Leases Table Here are setup instructions for each of them 2 6 1 LAN IP section eee 192 168 2 1 ELOGE EELE 255 255 255 0 CUPA ETE E MG Disabled Pla T Enabled IP address Please input the IP address of this router Subnet Mask Please input subnet mask for this network 802 1d If you wish to activate 802 1d spanning tree Spanning Tree function select Enabled for setup item 802 1d
82. s Tools Help Q ex x a JO search Sie Favorites z A 33 Address http 192 168 2 tfindex asp Broadband Router Home General Setup Status Too Quick Setup Wizard QuickSetup The Quick Setup Wizard provides only the necessary configurations to ae connect your Broadband router to your Internet Service Provider ISP through an external cable or a DSL modern General Setup The Broadband router supports advanced functions like Virtual Server Access Control Hacker Attack Detection and DMZ We highly recommend you keep the default settings Status Information ns The Broadband router s status information provides the following information about your Broadband router Hardware Firmware version Serial Number and its current operating status Tools Broadband router Tools Tools include Configuration tools Firmware upgrade and Reset Configuration tools allow you to Backup Restore or Restore to Factory Default setting for your Broadband router The Firmware upgrade tool allows you to upgrade your Broadband router s firrmwara Tha BEGET taal allawe wni ta racat waur Rraadhand rotor Internet 2 4 1 Time zone and time auto synchronization Please follow the following instructions to set time zone and time auto synchronization parameters Please click System menu on the left of web management interface then click Time Zone and the following message will be displayed on your web 2
83. s to distinguish one network application protocol over another Below is a list of common applications and protocol port numbers Application Protocol Port Number Telnet TCP 23 FTP TCP 21 SMTP TCP 25 POP3 TCP 110 H 323 TCP 1720 SNMP UCP 161 SNMP Trap UDP 162 HTTP TCP 80 PPTP TCP 1723 PC Anywhere TCP 5631 PC Anywhere UDP 5632 PPPoE Point to Point Protocol over Ethernet Point to Point Protocol is a secure data transmission method originally created for dial up connections PPPoE is for Ethernet connections PPPoE relies on two widely accepted standards Ethernet and the Point to Point Protocol It 86 is a communications protocol for transmitting information over Ethernet between different manufacturers Protocol A protocol is a set of rules for interaction agreed upon between multiple parties so that when they interface with each other based on such a protocol the interpretation of their behavior is well defined and can be made objectively without confusion or misunderstanding Router A router is an intelligent network device that forwards packets between different networks based on network layer address information such as IP addresses Subnet Mask A subnet mask which may be a part of the TCP IP information provided by your ISP is a set of four numbers e g 255 255 255 0 configured like an IP address It is used to create IP address numbers used only within a particular network as opposed to valid IP address numbers
84. sable bandwidth for this rule or max set the maximum bandwidth for the application allowed by this rule Local IP Address Specify the local source IP address that will be affected by this rule Please input the starting IP address in the left field and input the end IP address in the right field to define a range of IP addresses or just input the IP address in the left field to define a single IP address Local Port Range Please input the range of local source port number that will be affected by this rule If you want to apply this rule on port 80 to 90 please input 80 90 if you want to apply this rule on a single port just input the port number like 80 Remote IP Address Specify the remote destination IP address that will be affected by this rule Please input the starting IP address in the left field and input the end IP address in the right field to define a range of IP addresses or just input the IP address in the left field to define a single IP address Remote Port Range Please input the range of remote destination port number that will be affected by this rule If you want to apply this rule on port 80 to 90 please input 80 90 if you want to apply this rule on a single port just input the port number like 80 If the remote 57 destination IP address and or port number is universal just leave it blank Traffic Type Please select the traffic type of this rule av
85. select one of them but you have to make sure your wireless client support the cipher you selected Pre shared Key Format Select the type of pre shared key you can select Passphrase 8 or more alphanumerical characters up to 63 or Hex 64 characters of 0 9 and a f Pre shared Key Please input the WPA passphrase here After you finish WPA Pre shared key setting please click Apply button and the following message will be displayed on your web browser Please click Continue to back to previous setup menu to continue on other setup procedures or click Apply to reboot the router so the settings will take effect Please wait for about 30 seconds while router is rebooting NOTE Some wireless clients especially those manufactured before year 2003 only support WEP or WPA TKIP cipher A driver upgrade would be 49 needed for those clients to use WPA and WPA2 encryption 2 7 3 4 WPA RADIUS If you have a RADIUS server this router can work with it and provide safer wireless authentication WPA Unicast Cipher Suite RADIUS Server Port RADIUS Server Password RADIUS Server IP address WPA Unicast Cipher Suite Please select a type of WPA cipher suite Available options are WPA TKIP WPA2 AES and WPA2 Mixed You can select one of them but you have to make sure your wireless client RADIUS Server IP address Please input the IP address of your Radius RADIUS Ser
86. ss you re using this wireless router in a really big space you may not have to set output power to 100 This will enhance security malicious unknown users in distance will not be able to reach your wireless router WMM The short of Wi Fi MultiMedia it will enhance the data transfer performance of multimedia contents when they re being transferred over wireless network If you don t know what it is not sure if you need it it s safe to set this option to Enable however default value is Disable After you finish these wireless settings please click Apply button button and the following message will be displayed on your web browser Please click Continue to back to previous setup menu to continue on router setup or click Apply to reboot the router so the settings will take effect Please wait for about 30 seconds while router is rebooting 2 7 3 Wireless Security It s very important to set wireless security settings properly If you don t hackers and malicious users can reach your network and valuable data without your consent and this will cause serious security problem To set wireless security settings Please click Wireless menu on the left of web management interface then click Security Settings then follow the following instructions to set wireless security settings 46 Please select an encryption method from Encryption dropdown menu there are four optio
87. t modify default value if you don t know what it is default value is 100 DTIM Period Set the DTIM period of wireless radio Do not modify default value if you don t know what it is default value is 3 Data Rate Set the wireless data transfer rate to a certain value Since most of wireless devices will negotiate with each other and pick a proper data transfer rate automatically it s not necessary to change this value unless you know what will happen after modification N Data Rate Same as above but only for 802 11n clients Channel Width Set channel width of wireless radio Do not modify default value if you don t know what it is default setting is Auto 20 40 45 MHz Preamble Type Set the type of preamble do not modify default value if you don t know what it is default setting is Short Preamble Broadcast ESSID Decide if the wireless router will broadcast its own ESSID or not You can hide the ESSID of your wireless router set the option to Disable so only people those who know the ESSID of your wireless router can get connected CTS Protect Enabling this setting will reduce the chance of radio signal collisions between 802 11b and 802 11g n wireless access points It s recommended to set this option to Auto or Always However if you set to None your wireless router should be able to work fine too x Power You can set the output power of wireless radio Unle
88. t uploaded Restore to Factory Default Click this button to remove all settings you made and restore the configuration of this router back to factory default settings 79 3 6 Firmware Upgrade The system software used by this router is called as firmware just like any applications on your computer when you replace the old application with a new one your computer will be equipped with new function You can also use this firmware upgrade function to add new functions to your router even fix the bugs of this router To upgrade firmware please follow the following instructions Please click Tool located at the upper right corner of web management interface then click Firmware Upgrade on the left of web management interface then the following message will be displayed on your web browser Please click Next and the following message will be displayed Click Browse button first you ll be prompted to provide the filename of firmware upgrade file Please download the latest firmware file from our website and use it to upgrade your router After a firmware upgrade file is selected click Apply button and the router will start firmware upgrade procedure automatically The procedure may take several minutes please be patient NOTE Never interrupt the upgrade procedure by closing the web browser or physically disconnect your computer from router If the firmware you uploaded is corrupt the firmware u
89. th C Discard Ping From WAN C Port Scan C Sync Flood C Advance Settings Ping of Death Ping of Death is a special packet and it will cause certain computer to stop responding Check this box and the router will filter this kind of packet out Discard Ping From WAN Ping is a common and useful tool to know the connection status of a specified remote network device but some malicious intruder will try to fill your network bandwidth with a lot of PING request data packet to make your internet connection become very slow even unusable Check this box and the router will ignore all inbound PING request but when you activate this function you will not be able to ping your own router from internet too Port Scan Some malicious intruder will try to use a port scanner to know how many ports of your Internet IP address are open and they can collect a lot of valuable information by doing so Check this box and the router will block all traffics which are trying to scan your Internet IP address Sync Flood This is another kind of attack which uses a lot of fake connection request to consume the memory of your server and try to make your server become unusable Check this box and the router will filter this kind of traffic out Advanced Settings Click this button and you can set advanced settings of the DoS prevention method listed above please see section 3 3 3 1 DoS Advanced Settings below 72 After you finish with
90. ting Band Select the band you want to use two wireless routers must use the same setting Channel Number Select the channel you want to use two wireless 41 routers must use the same setting MAC address Input the MAC address of another wireless router Set Security Click to set security settings for this connection 2 7 1 4 Setup procedure for AP Bridge Point to Multi Point In this mode you can connect your wireless router with at least four wireless routers to expand the scope of wireless network and all clients wired only AP will not accept wireless clients in this mode of the wireless routers will think they re on the same physical network AP Bridge Point to Multi Point brite 2 4 GHz B G N m ooo000000000 ooooo0000000 ooo000000000 loooo00000000 Band Select the band you want to use all the wireless routers must use Channel Number MAC address 1 MAC address 2 MAC address 3 MAC address 4 the same setting Channel Number Select the channel you want to use all the wireless routers must use the same setting MAC address 1 to 4 4 7 Input the MAC address of other wireless routers Set Security Click to set security settings for this connection 2 7 1 5 Setup procedure for AP Bridge WDS In this mode you can expand the scope of network by combining up to four other access points together and every access point can sti
91. to PPPoE xDSL section above WAN interface settings must be correctly set or the Internet connection will fail even those settings of PPTP settings are correct Please contact your Internet service provider if you don t know what you should fill in these fields Now please go to L2TP settings section e L2TP Settings Password L2TP Gateway LULUH 1392 512 lt MTU Value lt 1492 CTs E eyes Continuous v nnect Idle Time Out f 1 1000 minutes User ID Please input user ID user name assigned by your Internet service provider here Password Please input the password assigned by your Internet service provider here L2TP Gateway Please input the IP address of PPTP gateway assigned by 19 your Internet service provider here MTU Please input the MTU value of your network connection here If you don t know you can use default value Connection Type Please select the connection type of Internet connection you wish to use please refer to last section for detailed descriptions Idle Time Out Please input the idle time out of Internet connection you wish to use and refer to last section for detailed descriptions When you finish with all settings please click OK If you want to go back to previous menu click Back 2 3 6 Setup procedure for Telstra Big Pond Telstra Big Pond Australia Only lf your Internet service is provided by Telstra Bi
92. ts advanced functions like Virtual Server Access Control Hacker Attack Detection and DMZ We highly recommend you keep the default settings status JR Status Information The Broadband router s status information provides the following information about your Broadband router Hardware Firmware version Serial Number and its current operating status Tools Broadband router Tools Tools include Configuration tools Firmware upgrade and Reset Configuration tools allow you to Backup Restore or Restore to Factory Default setting for your Broadband router The Firmware upgrade tool allows you to upgrade your Broadband router s firrewara Tha DESET tral allawe wan ta rocot vour Rroadhand rotor Internet NOTE If you can t see the web management interface and you re being prompted to input user name and password again it means you didn t input username and password correctly Please retype user name and password again If you re certain about the user name and password you type are correct please go to 4 2 Troubleshooting to perform a factory reset to set the password back to default value TIP This page shows the four major setting categories QuickSetup General Setup Status and Tools You can find the shortcut which leads to these setting categories at the upper right corner of every page and you can jump to another category directly by clicking the link and don t have to go back to the first page 2
93. up to four sets of WEP key and you can decide which key is being used by default here If you don t know which 47 one you should use select Key 1 Encryption Key 1 to 4 5 8 Input WEP key characters here the number of characters must be the same as the number displayed at Key Format field You can use any alphanumerical characters 0 9 a z and A Z if you select ASCII key format and if you select Hex as key format you can use characters 0 9 a f and A F You must enter at least one encryption key here and if you entered multiple WEP keys they should not be same with each other Enable 802 1x Authentication IEEE 802 1x is an authentication protocol Every user must use a valid account to login to this wireless router before accessing the wireless LAN The authentication is processed by a RADIUS server This mode only authenticates user by IEEE 802 1x but it does not encryption the data during communication If there is a RADIUS server in you environment please enable this function Check this box and another sub menu will appear Enable 802 1x Authentication RADIUS Server IP address Peace ee 1012 RADIUS Server Password RADIUS Server IP address Please input the IP address of radius server here RADIUS Server Port Please input the port number of radius server here RADIUS Server Password Please input the port number of radius password here TIP
94. uter and see if it works if not please restore your router to factory default settings pressing reset button for over 10 seconds e Set your computer to obtain an IP address automatically DHCP and see if your computer can get an IP address f If you did a firmware upgrade and this happens contact your dealer of purchase for help g If all above solutions don t work contact the dealer of purchase for help Can t get connected to a Go to Status gt Internet Connection Internet menu and check Internet connection status b Please be patient sometime Internet is just that slow c If you connect a computer to Internet directly before try to do that again and check if you can get connected to Internet with your computer directly attached to the device 82 provided by your Internet service provider d Check PPPoE L2TP PPTP user ID and password again e Call your Internet service provide and check if there s something wrong with their service f If you just can t connect to one or more website but you can still use other internet services please check URL Keyword filter g Try to reset the router and try again later h Reset the device provided by your Internet service provider too i Try to use IP address instead of hostname If you can use IP address to communicate with a remote server but can t use hostname please check DNS setting I can t
95. ver Port Please input the port number of your Radius authentication server here Default setting is 1812 e support the cipher you selected authentication server here o e authentication server here RADIUS Server Password Please input the password of your Radius After you finish with all settings please click Apply button and the following message will be displayed on your web browser Please click Continue to back to previous setup menu to continue on other setup procedures or click Apply to reboot the router so the settings will take effect Please wait for about 30 seconds while router is rebooting 2 7 4 Wireless Access Control This function will help you to prevent unauthorized users from connecting to your wireless router only those wireless devices who have the MAC address you assigned here can gain access to your wireless router You can use this function with other security measures described in previous section to create a safer wireless environment 50 Up to 20 MAC addresses can be assigned by using this function Please click Wireless menu on the left of web management interface then click Access Control and the following message will be displayed on your web browser MAC Address Filtering Table Now MAC address l Comment hy allows to entry 20 sets address only MAC address Comment a 11 22 33 44 55 66 LAB Computer Delete Delete
96. vice Provider has assigned a Fixed IP address enter the assigned IP Address Subnet Mask and the Gateway IP Address provided CO ee eae ee eee 192 160 1 10 ELIGEN EGEL 255 255 255 0 Era E TET CEGE 192 168 1 254 IP address assigned by your Service Provider Please input IP address assigned by your service provider Subnet Mask Please input subnet mask assigned by your service provider Service Provider Gateway Address Please input the IP address of DNS server provided by your service provider After you finish with all settings please click Apply button and the following message will be displayed on your web browser Please click Continue to back to previous setup menu to continue on other setup procedures or click Apply to reboot the router so the settings will take effect Please wait for about 30 seconds while router is rebooting If you want to reset all settings in this page back to previously saved value please click Cancel button 2 5 3 Setup procedure for PPPoE 26 PPPoE 2 Enter the PPPoE User Name and Password assigned by your Service Provider The Service Name is normally optional but may be required by some Service Providers Enter a Idle Time in minutes to define a maximum period of time for which the Internet connection is maintained during inactivity If the connection is inactive for longer than the Maximum Idle Time then the connection will be dro
97. y clicking the Select box of the mapping then click Delete Selected button to remove the mapping If there is no existing mapping this button will be grayed out Delete All Delete all mappings existed in virtual server table Reset Unselect all mappings After you finish with all settings please click Apply button and the following message will be displayed on your web browser Please click Continue to back to previous setup menu to continue on other setup 60 procedures or click Apply to reboot the router so the settings will take effect Please wait for about 30 seconds while router is rebooting If you want to reset all settings in this page back to previously saved value please click Cancel button 3 2 3 Virtual Server This function allows you to redirect a port on Internet IP address on WAN port to a specified port of an IP address on local network so you can setup an Internet service on the computer on local network without exposing it on Internet directly You can also build many sets of port redirection to provide many different Internet services on different local computers via a single Internet IP address Please click NAT menu on the left of web management interface then click Virtual Server and the following message will be displayed on your web browser C Enable Virtual Server Select v Both v Add Reset
98. ynamic IP 2 The Host Name is optional but may be required by some Service Providers The default MAC Address is set to the WAN physical interface on the Broadband router If required by your Service Provider you can use the Clane MAC Address button to copy the MAC Address of the Network Interface Card installed in your PC and replace the WAN MAC Address with this MAC Address LEEFT EIE OOOCOI000000 Clone Mac address Host Name Please input host name of your computer this is optional and only required if your service provider asks you to do so MAC Address Please input MAC address of your computer if your service provider only permits computer with certain MAC address to access internet If you re using the computer which used to connect to Internet via cable modem you can simply press Clone Mac address button to fill the MAC address field with the MAC address of your 25 computer After you finish with all settings please click Apply if you want to remove and value you entered please click Cancel After you click Apply the following message will be displayed on your web browser Please click Continue to back to previous setup menu to continue on router setup or click Apply to reboot the router so the settings will take effect Please wait for about 30 seconds while router is rebooting 2 5 2 Setup procedure for Static IP Static IP 2 If your Ser
99. your computers network devices network enabled consumer devices other than computers like game console or switch hub to the LAN port of the router ADSL or Cable Modem b Switch Hub 3 Connect the A C power adapter to the wall socket and then connect it to the Power socket of the router ADSL or Cable Modem 4 3 2 1 WAN S Switch Hub 4 Please check all LEDs on the front panel PWR LED should be steadily on WAN and LAN LEDs should be on if the computer network device connected to the respective port of the router is powered on and correctly connected If PWD LED is not on or any LED you expected is not on please recheck the cabling or jump to 4 2 Troubleshooting for possible reasons and solution 2 2 Connect to wireless broadband router by web browser After the network connection is built the next step you should do is setup the router with proper network parameters so it can work properly in your network environment Before you can connect to the router and start configuration procedures your computer must be able to get an IP address automatically use dynamic IP address If it s set to use static IP address or you re unsure please follow the following instructions

Zonet ZSR4124WE router

Contents

Download Pdf Manuals

Related Search

Related Contents