Akai ARC300I
Contents
1. I lt button for 1 2 seconds and then release 3 The unit will start seeking automatically and stop when the radio station is reached 4 Repeat steps 2 and 3 until the desired radio station is reached 5 Adjust the volume control to the desired volume level Preset Stations using Remote Handset You can store up to a total of 20 radio stations in memory 10 AM 10 FM Set to TUNER mode Turn to the desired radio station by MANUAL or AUTO tuning method Press PROG ADJ button to enter programming mode Press PRE or PRE button to select the desired station memory for storage Press PROG ADJ button again to confirm the setting Repeat steps 2 to 5 to store other stations Press PRE or PRE button to reload the preset stations in order The unit will return to normal TUNER mode if no buttons are pressed FM and FM Stereo Reception Press the ST MONO button on the remote handset to select MONO or STEREO reception mode Hints for Best Reception AM the receiver has a built in AM bar antenna If AM reception is weak slightly rotate or reposition the unit to improve the AM reception FM the receiver has an attached FM wire antenna at the back of the unit This wire should be fully unwound and extended at full length for best reception EN 39 iPod OPERATION TO USE THE DOCK WITH YOUR IPOD 1 Remove the iPod cover from the unit 2 Insta2. screen N Remark The LCD display supports English language only MP3 support Bitrate 32 kbps 320 kbps Sampling rate 32kHz 44 1kHz and 48kHz decode format The performance playing disc varies from the quality of recording disc and the method of recording The searching lead time for MP3 CD is longer than normal CD due to different format Play Mode Press the PLAY MODE button before or during play and a single track single folder MP3 only all tacks RANDOM and INTRO can be played Each press will toggle the play mode as follows FOR CD 1 REPEAT1 2 REPEAT ALL 3 RANDOM 4 INTRO FOR MP3 1 REPEAT1 2 REPEATALBUM 3 REPEATALL 4 RANDOM 5 INTRO 42 CARE amp MAINTENANCE Care of the Compact Disc To remove a disc from its storage case press down on the center of the case Q S and lift the disc out holding it carefully Ss by the edges gt O Fingerprints and dust should be carefully wiped off the disc s recorded surface with a soft cloth Unlike conventional records compact discs have no grooves to collect dust and microscopic debris so gently wiping with a soft cloth should remove most particles Wipe in a straight line from the inside to the outside of the disc Small particles and light stains should have absolutely no effect on reproduction quality Clean the disc periodically with a soft lint fr
3. the clock display will show 3 Turn on the power and select CD function if the LCD turns on then the power supply is normal and the system is ready to play music Battery Back up Batteries not included In the event of a power failure this unit will automatically switch to a battery or stand by circuit when the batteries are installed Open the BATTERY COMPARTMENT on the bottom of the unit and install 3 AAA batteries It is recommended that you use alkaline batteries for back up and to change the batteries every year or after a power outage of more than 12 hours EN 36 REMOTE CONTROL HANDSET 1 MUTE Press to activate deactivate MUTE function 2 STANDBY Press to turn power on off 3 FUNCTION Press to select the system for CD TUNER iPod 4 CD Press to switch to CD mode 5 PROG ADJ In CD or Tuner mode press to set CD or Tuner memory In Standby mode press to set clock 6 FOLDER In MP3 mode press to go to previous PRE album number In Tuner mode press to go to previous pre set station In iPod mode press to choose amenu item 7 FOLDER In MP3 mode press to go to the next PRE album number In Tuner mode press to go to next pre set station In iPod mode press to choose a menu item 8 9 MENU Press the MENU key to show iPod menu 9 IniPod MENU mode press the ENTER button to choose the menu 10 10 Selects the MP3 track skip in 10 each press 10 11 4 10 Sel
4. AKAI Operator s manual AUDIO CD DOCKING SYSTEM FOR IPOD ARC300 Operator s manual EN 34 44 2 SAFETY PRECAUTIONS WARNINGS To reduce the risk of fire or electric shock do EXPLANATION OF GRAPHIC SYMBOLS not expose this appliance to rain or moisture The lightning flash with arrowhead symbol with in CAUTION an equilateral triangle is intended to alert user to the presence of uninsulated dangerous voltage RISK OF ELECTRIC SHOCK within the product enclosure that may be of DO NOT OPEN sufficient magnitude to constitute a risk of electric shock to persons WARNING TO REDUCE THE RISK OF ELECTRIC SHOCK The exclamation point within an equilateral DO NOT REMOVE COVER NO USER SERVICEABLE triangle is intended to alert the user to the PARTS INSIDE REFER SERVICING TO QUALIFIED presence of important operating and maintenance servicing instruction in the literature accompanying the appliance SERVICE PERSONNEL HAZARD WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE ESD Remark In case of malfunction due to electrostatic discharge just reset the product reconnect of power source may be required to resume normal operation CLASS 1 LASER PRODUCT CAUTION INVISIBLE LASER RADIATION WHEN CLASS 1 LASER PRODUCT APPAREIL A LASERDE CLASSE1 OPEN AND INTERLOCK FAILED OR PRODUITLASER DE CLASSE1 DEFEATED AVOID DIRECT IXPOSURE TO LASER BEAM
5. This product contains a low power laser emitter EN 34 FEATURES AND CONTROLS OR ON EER SPEAKER LCD DISPLAY CD DOOR STANDBY ON BUTTON ALARM 1 BUTTON ALARM 2 BUTTON FOLDER MEMORY BUTTON iPod DOCK FOLDER MEMORY BUTTON 0 PLAY MODE BUTTON EN 35 PROG CLOCK ADJ BUTTON FUNCTION BUTTON SNOOZE BUTTON STEREO HEADPHONE JACK REMOTE SENSOR VOLUME BATTERY BACKUP COMPARTMENT bottom AC POWERCORD FM ANTENNA 3 5 7 8 1 6 10 f ham wll _ 11 655555 JQ 4247 CLEA se 4 16 13X42 Caution Usage of controls adjustments or performance of procedures other than those specified here may result in hazardous radiation exposure This unit should not be adjusted or repaired by anyone except for a qualified service technician Important Since movement of the CD mechanism and the sensitive circuitry may cause interference to radio tuners nearby switch this unit off while operating other devices Precautions for Use Installation Unpack all parts and remove protective material Do not connect the unit to a power outlet before checking the voltage and before all other connections have been made Do not cover any vents and make sure that there is space around the unit for ventillation Connection 1 Connect the power adapter to an AC outlet 2 When you first plug the unit in the unit will go to standby mode and
6. e control or main unit Start a song over or play the Press the previous rewind 144 button once to start a song over previous song press it twice to play the previous song on remote control or main unit To go back to the previous menu Press the MENU button on remote control To charge the battery When iPod is connected to this unit the battery wil start charging Fig 1 this icon will show when the battery is charging Fig 2 this icon will show when the battery is full charged 1 2 Charging Charged EN 40 PLAYING COMPACT DISCS Getting Started 1 Press CD button to select CD mode 2 Press the amp at the right hand corner of the CD door to open 3 Place the music disc with the printed side facing up into the tray and close the door 4 After a few seconds the display will show the total number of tracks amp playing time Play Pause Mode 1 Press the PLAY PAUSE button to start playback The first track will be played and the amp indicator will appear on the LCD display 2 To pause press the PLAY PAUSE button once The gt indicator will flash on the LCD display Press again to release and resume playback Stop Mode 1 If button is pressed during play or pause mode CD play will go to stop mode Skip Search Skip Up gt gt I Skip Downl lt lt Mode 1 During play mode press gt I lt to skip forward or backwa
7. ects the MP3 track skip in 10 each press 10 12 DBBS Press the DBBS button to change the bass boost 13 Press to reduce volume 14 TUNER Press to switch to Tuner mode 15 iPod Press to switch to iPod mode 16 ALARM2 Press to set or deactivate the ALARM 2 function 17 ALARM1 Press to set or deactivate the ALARM 1 function 18 PLAY MODE In CD mode press to switch between Repeat 1 Repeat All RANDOM and INTRO mode 19 ST MONO In Tuner mode press to switch between FM MONO FM STEREO 20 103 Press to show the 103 Tag if any 21 SLEEP Press to activate sleep function using CD RADIO iPod to turn off automatically after 90 60 30 or 15 minutes 22 SNOOZE Press to activate the SNOOZE function during ALARM 1 or ALARM 2 is activating the ALARM 1 or ALARM 2 will activate again 6 minutes later To cancel press ALARM 1 or ALARM 2 accordingly 23 BAND In CD mode press to terminate CD playback In Tuner mode press to switch between AM or FM 24 CD mode press once to start playback Press once to pause the disc play temporarily 25 gt gt In Tuner mode press to increase to the next frequency or press and hold to search forward 26 In CD mode press once to skip to previous track press and hold to search backwards In Tuner mode press to decrease frequency 27 EQ Press to select the presets EQ mode This unit provides 4 sound modes to enhance your listening quality You can select the desired e
8. ee dry cloth Never use detergents or abrasive cleaner s to clean the disc If necessary use a CD cleaning kit e Never write on or affix labels to the surface of compact discs Care of the Cabinet If the cabinet becomes dusty wipe it with a soft dry dust cloth Do not use any wax polish sprays or abrasive cleaners on the cabinet Caution Keep away from water or other liquids that may get inside the unit while cleaning EN 43 SPECIFICATIONS General Power Supply AC 230V 50Hz Power Consumption 16 watt Standby Consumption 3 watts Dimensions of Unit 9 13 16 x 7 1 16 41 16 inches W xH x L 250 x 179 x 103mm W x H x L Frequency Range AM 522 1620 kHz FM 87 5 108 5 MHz Audio Section Output Power 2 1 5W 5 Speaker 8 Ohms Specifications are subject to change without notice SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE This symbol the product or the instructions means that your electrical and electronic equipment shoule be disposed at the end of its life separately from your household waste There are separate collection systems for recycling in the EU EN For more information please contect the local authority or your retaiter where you purchased the product For more information and warranty conditions please visit www akai eu EN 44
9. ffect by pressing the EQ button repeatedly for the following sequence FLAT gt CLASSIC gt ROCK gt POP JAZZ 28 d Press to increase volume REMARKS Insert 2 AAA batteries not included before using Corrosion oxidation battery leakage and any other gradually acidic defect of this nature will invalidate the guarantee EN 37 CLOCK SETTINGS Setting the Clock can only be set during standby mode 1 Press PROG CLOCK ADJ button Either 12H or 24H will display 2 Choose 12 24 HRS by pressing gt button then press PROG CLOCK ADJ button 3 Press gt button for HOUR setting then press PROG CLOCK ADJ button to store 4 Press gt button for MINUTES setting and press PROG CLOCK ADJ button to store pea the Alarm 1 wake to CD iPod Tuner Press the ALARM 1 button the ALARM 1 icon will be shown on the display 2 Press the FUNCTION button to select your desired source CD iPOD or TUNER then press VOL or VOL to adjust the volume level 3 Press the I lt or gt button to set the hours Press ALARM 1 button to store 4 Then Press the kt or gt buttons to set the minutes Press ALARM 1 button to store 5 Switch the system to Standby mode At the preset time the selected source will play press ALARM 1 button to cancel The ALARM 1 icon is still be shown on the display for function the next day 6 To completely turn off ALARM 1 function press ALARM 1 butto
10. ll the iPod Dock Adapter into Dock then put your iPod in the Dock on the unit Dock adapter is a iPod accessories available separately and fits with your iPod product Note 1 After placing the iPod in the Dock all iPod functions can be operated by remote controller please don t try to use the iPod controls because the iPod connector may be damaged while the dock is connected with your iPod 2 This player can support following model number iPod A iPod mini 4G amp 6G B iPod photo 40G amp 60G C iPod nano 2G amp 4G D 5G iPod and U2 iPod with video 30G E 5G iPod with video F iPod nano 2G amp 4G amp 8G G iPod nano 4G amp 8G H iPod Touch 3 Playing music Throught the unit speakers Using the iPod Dock you can play music from iPod through the unit speakers and operated with You can remove the Dock adapter remote controller with your fingernail by using this slot 1 Place iPod in the Dock 2 Use the remote controller to play iPod with following steps Enter main menu Press the MENU button on remote control The top and bottom choose Press the PRE PRE button on remote control or main unit To choose an item Press the ENTER button on remote control Play or pause a song Press the play pause 1 button on remote control main unit Change the volume Press the VOL or VOL button on remote control or main unit Skip to the next song Press the next fast forward gt p button on remot
11. n once again the ALARM 1 icon will not be shown again NOTE If the selected source CD is not available when the preset time is reached BUZZER will be selected automatically Setting the Alarm 2 Buzzer 1 Press the ALARM 2 button the ALARM 2 icon will be shown on the display 2 Press the gt buttons to set the hours Press ALARM 2 button to store 3 Then Press the ke or gt buttons to set the minutes Press ALARM 2 button to store 4 Switch the system to Standby mode At the preset time the BUZZER source will play press ALARM 2 button to cancel The ALARM 2 icon is still be shown on the display for function the next day 5 To completely turn off ALARM 2 function press ALARM 2 button once again the ALARM 2 icon will not be shown again Sleep Function The sleep function can only be set while the unit is on in either RADIO CD or iPod mode To activate press the SLEEP button on the remote handset Continue pressing the SLEEP button one press at a time to set the timer to either 90 60 30 15 minutes or OFF EN 38 LISTENING TO THE RADIO Manual Tuning 1 In Tuner mode Press BAND button to select the desired BAND AM or FM 2 Tune to the desired station by pressing the gt ke lt button 3 Adjust volume control to the desired volume level Auto Tuning 1 In Tuner mode press W BAND button to select the desired BAND AM or FM 2 Press and hold the
12. rds The track will play automatically 2 During pause mode press gt or to skip forward or backwards then press the play button NOTE Press and hold down the buttons to activate the search function for a particular track For MP3 Disc 1 Press FOLDER PRE FOLDER PRE button to select the album number 2 Press gt or ea button to select the track number 3 When the desired track is selected press the PLAY button to start playback For ID3 Tag MP3 Disc Only 1 Press the ID3 button on the remote control 2 103 icon will be shown on the display 3 The TITLE ARTIST and ALBUM information will be shown on the display if any EN 41 PLAYING COMPACT DISCS CD Programming Up to 20 tracks can be programmed to play in any sequence Before use be sure to press the STOP button 1 Set in CD mode 2 Press the PROG ADJ button MEMORY will flash on the LCD display It will indicate program number and digits of the track number to be programmed Select a desired track by pressing the gt or ke buttons Press the PROG ADJ button to store the track into memory Repeat steps 3 and 4 to enter additional tracks into the memory if desired When all the desired tracks have been programmed press the PLAY PAUSE button to play the disc in the order you have programmed Press the STOP button twice to terminate programmed play The PROGRAM icon will disappear on the
Download Pdf Manuals
Related Search