TEAC DVW/D17A/KIT/H
Contents
1. 1x3 DVD Duplicator 1x7 DVD Duplicator AC power cable Figure 1 DVD Duplicator Unit Package Contents Note If any of the items above is missing from your package upon purchase please contact your vendor immediately 2 TEAC Tower DVD Duplicator User s Manual Front Panel Front Panel Figure 2 illustrates the front panel of the Tower DVD Duplicator unit M1 source drive ca O target drive I O target drive 9 s o 4 power switch we EN LED status indicators O Figure 2 Front Panel of the DVD Duplicator Unit source drive Insert the disc to be copied into the source drive Use the disc tray to load a DVD into the drive You can open the tray by pressing the eject button if the tray fails to open you can use the emergency eject mechanism You can close the tray by pressing the eject button Notes Q TEAC strongly recommends that you do not push the tray in to close it Please press the eject button to eject or retract the tray Q The Tower DVD Duplicator may include an internal hard disk drive as an alternate source drive Please refer to Specifications on page 29 for detailed information on the model that you purchased TEAC Tower DVD Duplicator User s Manual Front Panel O LCD control panel Use the control panel buttons to naviga2. 11 2 CD Burn Speed The CD Burn Speed setting controls the writing speed of the target drive when recording onto CD R CD RW media The default value is AUTO which writes at the highest speed allowed by the media 11 3 DVD Burn Speed The DVD Burn Speed setting controls the writing speed of the target drive when recording onto DVD RW media The default value is MAXIMUM which writes at the highest speed available on the target drive On occasion using the maximum writing speed will cause copy failure due to poor quality DVD RW discs In this case TEAC recommends that you reduce the writing speed 11 4 Read Speed The Read Speed function enables you to set the reading speed of the target drive MAXIMUM is the default setting 11 5 Auto Start Drive The Auto Start Drive setting enables the DVD Duplicator to auto start the copy or test process as soon as a blank disc is inserted into the target drive The default setting is OFF TEAC Tower DVD Duplicator User s Manual 17 11 6 Startup Menu 11 6 Startup Menu The Startup Menu setting enables you to select a menu item to be displayed as the first menu item when you turn on the DVD Duplicator COPY is the default 11 7 Auto Verify The Auto Verity setting controls auto verification of discs after a copy operation The default setting is OFF 11 8 Auto Compare The Auto Compare setting controls auto comparison of data between source and target discs after a copy operation The def
3. 4 Compare Image 9 5 Select Image 9 6 Image Src Drive 9H ImageFormat Info 10 Edit Track for CD only 10 1 CD to CD 10 2 CD to HDD available only on DVW D13H and DVW D17H 10 3 Play Audio Track 104 Close Session 11 Setup 11 1 Language Default is English 11 2 CD Burn Speed Default is Auto 11 3 DVD Burn Speed Default is Maximum 114 Read Speed Default is Maximum 11 5 Auto Start Drive Default is Off 11 6 Startup Menu Default is Copy 11 7 Auto Verify Default is Off 11 8 Auto Compare Default is Off 11 9 Auto Prescan Default is Off 11 10 Eject Disc Default is Eject Good Only 11 11 Burn on the Fly Default is On 11 12 Burn Mode Default is DAO 11 13 Display Time Default Off 11 14 Button Sound Default is On 11 15 Device Info 11 16 System Info 11 17 Quick Erase 11 18 Full Erase 11 19 Auto Close Tray 11 20 Quick Compare 1121 Audio Burn Speed 12 Advanced Setup Adv Setup 12 1 UnderRun Protect Default is On 12 2 Overburn Default is Off 12 3 Read Error Skip Default is Off 124 Format HDD factory use only 12 5 Verify HDD factory use only 12 6 Burn in 12 7 Update Firmware 12 8 Compare Firmware TEAC Tower DVD Duplicator User s Manual 23 12 9 12 10 12 11 12 12 12 13 12 14 12 15 24 H W Diagnostic Load Default CD G Default is Off ISRC amp MCN Default is Off Switch USB Mode Optional CD Text Default is Off MultiSession DVD TEAC Tower DVD
4. Step 12 If you want to copy an image file from another partition into which you have already loaded data continue with Step 10 Press the O buttons to select function 9 5 Select Image then press the ENT button to access the Select a Partition submenu The Select a Partition submenu also enables you to select a partition A B C etc from which you want to copy an image file TEAC Tower DVD Duplicator User s Manual 11 12 13 14 15 16 Loading Data to and Copying from the Hard Disk Source Drive Press the O buttons to select the partition you wish to copy from then press the ENT button The data will be copied from the selected partition when you specify the hard disk drive as the source and execute the copy function as described in Steps 13 through 16 Press the ESC button twice to exit to the DVD Duplicator s main menu Press the O buttons to select function menu 8 Select Source then press the ENT button to access a list of available source drive options Press the 2 buttons to select the hard disk drive then press the ENT button The hard disk drive is now designated as the source drive Press the O button to switch to function 1 Copy The LCD will display a message similar to the following 1 Copy P A This message indicates that the data will be copied from the hard disk drive s partition A which was selected in Step 11 If you selected part
5. Technical Support and Warranty This appendix explains how to contact technical support at TEAC America Inc and provides Limited Warranty information ii TEAC Tower DVD Duplicator User s Manual Table of Contents Safety Precautions a iube b bad e eges i Copyright and Trademark Information ssseeee eee ii Piracy Statement Oia ii About This Manual ii ini il PA O Ne fy et M Chapter 1 Introduction o oooooooncorcrcrororonrrnnoron s 1 DVD Duplicator Package Contents sseeeeeee eee 2 Front Panel i e e p RR A Ree es aw eR eeu s 3 Rear Panel Past a E ee br era 5 Chapter 2 Using the DVD Duplicator cee cece eee eee 7 DELP ici tbatacAne eave AAA A nde ie ens i Basic OPeratlOn Mc 8 Copying from the Optical DVD Source Drive oute nsii eee 8 Loading Data to and Copying from the Hard Disk Source Drive 9 Chapter 3 Tower DVD Duplicator Functions o o oo oo oo o 13 MAC OP oa e PR A E 13 LES AA a ETES 13 I TESE ac CODY reiden ra Ae Pavese uk onam dn Ge Unde dec dena c dec aeo Ron 14 4 Verify A ARE NU ERRARE PENQAN NND NE bere UEM SR o ER Ronin 14 COMPAS a NES due da Bed ides Sinbad adn pco 14 6 PreScan id a eb debe edes unas 14 7 Disce Info e eR SERERE REGE te ie qd p EE Y SERVE TR 14 5 Select Soure esses A E RM UR Oe A AAA reas 14 OTIm age cesse ke RE E cR ee RR RES A RESET YE HQ RE RN 15 LLO n ttbi arra per dade eget doped esp b d aee dede den 15 9 2 Del
6. e selector d Eh p o EN o E AC IN power connector Figure 4 Rear Panel of the DVD Duplicator Unit cooling fan Ball bearing fans cool the DVD Duplicator 7 AC voltage selector Use this switch to select either 115VAC or 220VAC Caution Before you turn on the power to the DVD Duplicator make sure the correct voltage is selected Otherwise you risk damage to the unit The default setting is 115VAC ACIN power connector Connect the included AC power cable to this input connector Plug the other end of the power cable into a three prong receptacle AC power outlet Caution Do not attempt to bypass the grounding plug Otherwise you risk electrical shock or damage to the unit Note To ensure proper operation use only the original AC power cable with your TEAC Tower DVD Duplicator unit TEAC Tower DVD Duplicator User s Manual TEAC Tower DVD Duplicator User s Manual Chapter 2 Using the DVD Duplicator This chapter explains how to set up the DVD Duplicator as well as basic Operation and menu functions Note The following instructions are applicable to 1x3 and 1x7 Tower DVD Duplicators The primary difference between models is the number of target drives and the inclusion of an optional hard disk drive Please refer to Specifications on page 29 for detailed information on your model Setup 1 Carefully remove the DVD Duplicator unit AC power cord and user s manua
7. hard disk Image load Fail The image has not been loaded successfully from DVD to the hard disk HDD too small to handle The hard disk capacity is insufficient to store the data image image at least 5Gbytes is required No Valid HDD The system cannot locate a hard disk HDD too small The hard disk capacity is too small No Image in Partition xx There is no data image in the specified partition Image Exists Overwrite The current partition contains a data image Confirm the overwriting request Delete Image in Partition xx Confirm the request to delete the data image in the spec ified partition Partition Damage The partition is damaged Verify Disk Or Partition Do you want to verify the entire hard disk or only a parti tion Verify Hard Disk OK The hard disk has been verified successfully Verify the Hard Disk Fail The hard disk has not been verified successfully Verify Partition Header Verify the partition header Select HDD First First select a formatted hard disk Audio Editing Message Meaning Lost selected Tracks Abort and delete the selected tracks End edit disc and burn Finish the music disc editing and start to copy Continue edit next Disc Do you want to continue the music disc editing Target Overflow Re Select The disc capacity is insufficient to store the selected tracks Please s
8. D ROM drive is the default source drive The internal hard disk drive was formatted and partitioned at the factory Each partition occupies 5GB of hard disk space The number of partitions depends on the capacity of the hard disk drive Partitions are arranged alphabetically and initially contain no data A set of data loaded into a partition on the hard disk drive is called an image file To use the hard disk drive as the source drive you must first load an image file from a DVD onto a partition on the hard disk drive select the partition that contains the data you want to copy specify the hard disk drive as the source drive then execute the copy function 1 Insert a source DVD into the DVD ROM drive This disc DVD ROM or DVD contains the data that you wish to copy to the partition on the internal hard disk drive 2 Press the Q O buttons to select function menu 9 Image then press the ENT button The Image menu includes the Load Delete Image Image Info Compare Image Select Image Image Src Drive and ImageFormat Info functions 3 Press the Q O buttons to select function 9 5 Select Image then press the ENT button to access the Select a Partition submenu The Select a Partition submenu enables you to select a partition A B C etc into which to load an image file on the hard disk drive When the unit is shipped from the factory the partitions on the hard disk drive contain no data The LCD will displ
9. Duplicator User s Manual Appendix B LCD Messages This appendix explains the messages that may appear on the LCD panel Normal Conditions for all DVD Duplicator models Message Meaning Initialize SDRAM Initialize system memory Detect drives User Abort Detect the drives connected to the system Cancel a job during operation Analyzing Analyze the source disc Source Drive Not Ready Source drive is not ready to read Target Drive Not Ready Target drive is not ready to write Erasing disc The system is erasing the data on the disc Source Disc Not Ready Target Disc Not Ready Source disc is not ready to be read Target disc is not ready to be written into Fail to get Drive Info Drive information cannot be obtained Fail to get SRC Disc Info Information about a source disc cannot be obtained Save new config Fail The new configuration settings cannot be saved Load Default Config Do you want to load the default settings Src amp Tgt can t in the same channel During comparison the source and target discs cannot occupy the same channel Preparing The system is preparing to record Check Target Please Wait The system is checking the target device Audio Disc Can t compare The system cannot compare the audio disc Identical Read disc error Comparison results are identical During a comparison the disc coul
10. SE SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND OR DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC RIGHTS AND MAY VARY FROM SOME OF THE RIGHTS PROVIDED BY LAW THESE RIGHTS MAY VARY FROM STATE TO STATE To contact the TEAC Service Center in the United States Tel 1 323 727 7694 or 1 323 727 7616 Fax 1 323 727 7606 E mail dssvce Oteac com TEAC America Inc 7733 Telegraph Road Montebello California 90640 TEAC Tower DVD Duplicator User s Manual 31
11. Tower DVD Duplicator User s Manual DVW D13 DVW D13H DVW D17 DVW D17H TEAC Safety Precautions TEAC DVD Duplicator systems are high precision electronic devices Do not use them in any manner other than as specified in this manual Please read this manual in its entirety before you begin the installation procedure Use of controls adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure To prevent fire or shock do not expose the unit to moisture or rain To prevent electrical shock do not attempt to disassemble the DVD Duplicator system Refer servicing to authorized personnel TEAC DVD Duplicator drives utilize a laser beam that can be harmful to your eyes Do not disassemble the cabinet or unit Do not attempt to look through the front panel or into the unit while the power is turned on A user who changes or modifies the unit or operating procedures specified herein without expressed written approval by the manufacturer will void user authority to operate the equipment Specifications and features subject to change without notice or obligation TEAC Tower DVD Duplicator User s Manual Copyright and Trademark Information O Copyright 2005 TEAC America Inc All rights reserved TEAC America Inc reserves the right to modify product offerings or specifications without advanced notice No part of this publication may be reproduced in any format without the exp
12. ault function resets all settings to factory default values It is recommended that you reset to the default values if the DVD Duplicator fails to function properly after you make changes to the original configuration 12 11 CD G The CD G function enables or disables CD G karaoke CD format support The default setting is OFF Note The CD G value must be set to OFF before you can use the Track Extraction features 12 12 ISRC amp MCN The ISRC amp MCN function enables or disables ISRC and MCN format support The default setting is OFF 12 13 Switch USB Mode The Switch USB Mode function is not applicable to TEAC Tower DVD Duplicators 12 14 CD Text The CD Text function enables or disables the copying of CD Text discs The default setting is OFF 12 15 MultiSession DVD The MultiSession DVD function is designed for DVDs with multiple sessions The default setting is OFF but when you want to copy a multi session DVD disc you must set this function to ON Note that you should insert the source DVD with multiple sessions into a DVD writer not into the DVD ROM drive You will need to change the source drive using function 8 Select Source 22 TEAC Tower DVD Duplicator User s Manual Appendix A List of Functions 1 Copy 2 Test 3 Test amp Copy 4 Verify 5 Compare 6 Prescan 7 Disc Info 8 Select Source 9 Image available only on DVW D13H and DVW D17H 9 1 Load 9 2 Delete Image 9 3 Image Info 9
13. ault setting is OFF 11 9 Auto Prescan The Auto Prescan setting controls automatic prescan of the source disc whenever a data audio disc is inserted in the source drive The default setting is OFF 11 10 Eject Disc The Eject Disc setting controls the ejection of discs by the target drive Three options are available Q Eject Good Only This option ejects only successfully copied discs This is the default setting Q Eject All Disc This option ejects successful and failed copy discs A Do Not Eject With this option all discs remain in the target drive Manual ejection is required after every copy operation 11 11 Burn on the Fly The Burn on the Fly function enables you to control the copy operation When the setting is ON data is copied directly from the source DVD to the target DVDs When the setting is OFF the DVD Duplicator first loads the data into a partition on the hard disk drive then copies the data to the target DVDs This function is valid only on Tower DVD Duplicators that feature an internal hard disk drive 18 TEAC Tower DVD Duplicator User s Manual 11 12 Burn Mode 11 12 Burn Mode The Burn Mode setting enables you to select from two writing methods for CD R media A Disc At Once DAO Q Track At Once TAO DAO is the default setting 11 13 Display Time The Display Time function displays the total time of each copy operation The default setting is OFF 11 14 Button Sound The B
14. ay a message similar to the following for each corresponding partition Select a Partition No image in A TEAC Tower DVD Duplicator User s Manual 9 Loading Data to and Copying from the Hard Disk Source Drive 4 10 Press the Y buttons to select the desired partition letter The LCD will display partition A as the first option but you can select any partition letter at any time Press the ENT button to confirm the desired partition The LCD will display a message similar to the following Set Partition To A If you selected partition B the LCD will display the message Set Partition To B and so on Press the ESC button to return to function menu 9 Image Press the O buttons to select function 9 1 Load then press the ENT button to transfer data from the DVD to the specified parti tion on the hard disk drive The data image file on the DVD in the source drive will be copied onto the partition you selected in Step 5 Note To help you quickly locate your data in the future TEAC recommends that you keep track of the data that you load into each partition Once the data is loaded successfully remove the source disc from the DVD ROM drive Repeat Steps 1 through 8 to load additional image files from other DVDs to other partitions if desired At this point the selected partition is the same as the one you selected in Step 5 above If you want to copy from this partition skip to
15. corders TEAC 16X DVD RW Drive Interface IDE ATAPI Read Speed DVD 16x CD 48x Write Speed DVD 16x CD 48x Drive Buffer Size 2MB System Buffer Size 1x3 32MB 1x7 64MB Supported Discs DVD R DVD RW DVD DL DVD R DVD RW CD R and CD RW discs System Control Copy and Search Buttons System Display LCD Panel LED Indicator Write Method Auto Detect DAO TAO Operation Mode Copy Test Scan Compare Firmware Upgrade Via CD ROM DVD ROM Power Supply AC Input 115 230V TEAC Tower DVD Duplicator User s Manual 29 Limited Warranty Appendix E Technical Support and Warranty For technical support please contact the TEAC America Support Center TEAC America Inc USA Technical Support Telephone 323 727 4860 Fax 323 869 8751 Monday Friday 8 00 a m 5 00 pm PST http www teac com DSPD techsupport America htm E mail dspdtsgOteac com Limited Warranty This product is warranted by TEAC America Inc against defects in materials and workmanship LENGTH OF WARRANTY This warranty will be effective for both labor and parts and this warranty will be effective for one 1 year from the date of original purchase WHO MAY ENFORCE THE WARRANTY This warranty is valid only in the United States and enforceable only by the original purchaser This warranty is not valid outside the United States WHAT IS NOT COVERED BY THIS WARRANTY 1 Damage to or deterioration of the external cabinet Damage resul
16. d not be read Cannot read TOC The system cannot read the contents of the disc TOC not match Comparison results are not identical Source Disc Empty The source disc contains no data Target overflow The target disc capacity is insufficient to store new data Target Disc Not Empty Press a Key to Eject Good Disc The target disc still contains data Press any key to eject a disc after copying Copy suc cessful Press a key to Eject Fail Disc Press any key to eject a disc after copying Copy failed DVD RW does not Support the Func DVD RW does not support this function Hold ESC to exit Press ESC for one second to terminate the test All data will be lost erase All data on the disc will be lost Confirm erasure request Erase Finished The erasing of the data is complete No Erasing to Disc in DVD RW The disc in the DVD RW drive is not rewritable TEAC Tower DVD Duplicator User s Manual 25 Normal Conditions for models that feature a hard disk drive Message Meaning HDD not Format The hard disk has not been formatted Format HDD Do you want to format the hard disk All data will be lost format All data on the hard disk will be lost Confirm the format request Format HDD OK Formatting of the hard disk is complete Image load OK The image has been successfully loaded from DVD to the
17. d x 2 a o as 20 12 Advanced Setup Adv Setup 0 0 0 0c cece ccc ce cece eee ee oo 20 12 1 UnderRun Protect oret eL na eia A e 20 12 2 Overburen ee C ETEEN ETE RE eR Eu 20 123 Read EDESA e a ed REX EE 20 12 4 Format HDD cia 21 MN AAA X PEE 21 A Lice ee ese ue vae X OR RE E E EEREN 21 12 7 Update Ei Ware la sn det a deta Ra ah 21 12 8 Compare Firm ware ccc Soo afta wih ee 21 129 H W Diagnostic A Rec abate Rede cD 21 1210 Load Detalle 22 12 11 CDAG sir A ha eee Taree Lame eae es 22 12 12 ISRC amp MON ipaq s das 22 12 13 Switch USB Mode ori isan ucts ER RE ERE ERI RU RR ae uos 22 A CDSTEXt oot a anb bota cade pese 22 12 15 MultiSession DVD ir eem RR CR Re Heer YR ee eR 22 Appendix A List of Functions esee 23 Appendix B LCD Messages eeeeeeeeeee e hn 25 Normal Conditions for all DVD Duplicator models 0 00 cee eee eee 25 Normal Conditions for models that feature a hard disk drive 26 Audio Editi etcetera e petentes eei Par s Orari 26 Appendix C About DVD R and DVD RW Discs o ooooooo 27 Hardline DIS ient etis audited red 27 Loading and Ejecting DISCS voii A des EF s 28 Appendix D Specifications 0 cece cece cece cece een eeee 29 Appendix E Technical Support and Warranty ees 30 Limited Warranty eso e M ODIERP ESSEN CRI CH ON ER ER REG eu erede 30 iv TEAC Tower DVD Duplicator User s Manual List of Figures Figure 1 DVD Dup
18. data may be damaged and the data they contained may be rendered unrecoverable It may be necessary to re start the DVD Duplicator if the target drive hangs during a sudden termination 3 Test amp Copy The Test 8 Copy function performs the test simulation and the copy process in one step The copy process is performed only if the simulation detects no problems If the simulation fails the copy process is cancelled 4 Verify The Verify function verifies that the target disc was written completely and with no errors 5 Compare The Compare function compares data on the source and target discs after the copy process is complete Note This function works only with data discs 6 Prescan The Prescan function is performed on the source drive This function scans the disc to determine the maximum data audio extraction speed 7 Disc Info The Disc Info function displays detailed information about the source disc including sessions tracks capacity etc 8 Select Source The Select Source function enables you to select a drive DVD ROM drive DVD Writer drive or hard disk drive as the source from which to copy You can select a hard disk drive only on those Tower DVD Duplicator systems that feature a factory installed hard disk drive 14 TEAC Tower DVD Duplicator User s Manual 9 Image 9 Image The Image menu which consists of seven functions 9 1 through 9 7 is valid only on Tower DVD Duplicato
19. elect fewer tracks Close all disc s session Confirm the closing of disc sessions Can t edit HDD The hard disk cannot be edited as a source audio disc NO AUDIO track in this disc The source disc contains no audio tracks Insert next disc Insert the next audio disc Sessions were closed already Burn or Move to partition The disc sessions have already been closed Do you want to copy the data directly to disc or transfer the data to a hard disk partition Tgt overflow del last trk Ins empty disc Continue Disc capacity is insufficient to store the selected tracks Do you want to delete the last track Do you want to insert a blank disc and continue copying 26 TEAC Tower DVD Duplicator User s Manual Normal Conditions for models that feature a hard disk drive Appendix C About DVD R and DVD RW Discs This appendix explains how to handle load and eject DVD R and DVD RW discs Handling Discs Q Handle compact discs only by their edges to avoid getting fingerprints on the surface Do not touch the disc s data surface unlabeled side Q Do not place discs in direct sunlight or in locations subject to high humidity high temperatures or dusty conditions A If it becomes necessary to clean a disc due to erratic operation visible dust or smudges gently wipe the surface of the disc from the center to the outside edge Do not use benzene alcohol thinner or other solv
20. ents wipe disc surface from handle discs center to outside edge by their edges GM Figure 6 How to Handle Compact Discs DVD R and DVD RW TEAC Tower DVD Duplicator User s Manual 27 Loading and Ejecting Discs To load a disc into the source or a target drive first open the disc tray by pressing the Eject button on the front of the drive Place the disc on the disc tray with its label side facing up Then press the Eject button again to retract the disc tray back into the drive To eject a disc from the source or a target drive press the Eject button on the front of the drive to extend the disc tray Remove the disc from the disc tray and place it in its protective case Then press the Eject button again to retract the disc tray back into the drive Press the Eject button to extend and retract the disc tray Figure 7 Ejecting the Disc Tray 28 TEAC Tower DVD Duplicator User s Manual Loading and Ejecting Discs Appendix D Specifications The following table lists the product specifications for the TEAC Tower DVD Duplicator Model DVW D13 DVW D13H DVW D17 DVW D17H HDD Capacity None 80GB None 80GB Weight 22 lbs 23 5 lbs 37 lbs 38 5 lbs Dimensions HxWxD 10 5 x 7 5 x 17 25 17 25 x 7 5 x 18 DVD Re
21. ert a source disc in the source drive and a blank DVD R disc in as many of the target drives as you desire Note If your Tower DVD Duplicator features a factory installed hard disk drive and you wish to copy data from a partition on the hard disk refer to Loading Data to and Copying from the Hard Disk Source Drive on page 9 3 Press the ENT button When the copy operation is complete the target drives eject the copied discs 4 To make additional copies of the same source disc insert another blank DVD R disc in each of the target drives and press the ENT button Otherwise press ESC to return to the main menu Note You can use DVD RW discs that already contain data i e DVD RW discs that are not fully blank as target discs However the data stored on the DVD RW disc will be erased automatically before the new data is copied No special setting or procedure is required to erase the old data 2 Test The Test function simulates writing to the target disc Discs will remain blank after the test is complete This function is recommended if you are using unsupported media This function enables the target drive to adjust its laser to the proper intensity TEAC Tower DVD Duplicator User s Manual 13 3 Test amp Copy Note Unexpected termination or cancellation of a test will not affect a target DVD R disc The target DVD R disc will remain blank and available for use However DVD RW discs that contain
22. ete Image eoe e RA e e eek eR a 15 ESSA TET UNE Oa yee hese RTT ERR CT 15 DA Compare Images io e acoso atus ee pg fupe Ped s od a ls 15 A RPM 15 9 6 Image Sre Drive ina ao CAN EEG NIE ed ce Reed 15 97 mae FOLIA Infor sos etos er Quos e qa SOROR RD ERR eae oie 16 10 Edit Track for CD only 2cescce ese ee e eh ace 16 101 CDt CD Edit ipe ERR As 16 10 2 CD to HDD i gat cee capa ve E prd EUN dap 16 103 Play Audio Track siria PET UE kA gh ame T OPEN RA 16 10 4 Close Session a SEED 17 TI Setup nxirios ic e eem REY CR REC ES HET RR CER ER HR RR UR 17 EIN Eet eea Teea ED 17 I CD B Speed a 17 11 3 VI BUMS Peed x15 eost tace cR ton rrt te etc NEE KOE 17 IT Read Speed ii tte pura paese m xd anseres ei 17 S Auto Start DIVE aeos eO DIOR e avant Uh RR Ares de 17 11 6 Startup Menu sci dr e eere Dee Rc ERR YR ROC Une Mer dre RS SERIEN 18 DI TAUEG Verkty oos tetra Bice aie Aan a aa A a O 18 TEAC Tower DVD Duplicator User s Manual iii Table of Contents 11 8 Auto COMPAL sii A A a UR CS 18 11 9 Auto PresCant 200 E Raed ere ER en bai 18 AN O ek Bek a eb VEI TEE 18 11 11 Burn on the Fly isset rr e IRURE 18 1112 Burn Mode tesi A A A a ad CG LR 19 1113 Display Time ti id ada Ro 19 LT TA Buton Sound deseas A tee runc era gu om ch 19 11 15 Device Info a e e Ree 19 IER i i on a dd O a e a 19 1117 Quick Ets ia A a iia 19 MN A O AS 19 UT 19 Auto Close Tray uan voe ite bv AA epi 19 11 20 Quick COMPITE 0 AAA 20 11 21 Audio Burn Spee
23. ition B the LCD will display the message 1 Copy P B and so on Place a blank DVD R disc into each of the target drives then press the ENT button to start copying TEAC Tower DVD Duplicator User s Manual 11 Note Q With the default setting after source data has been successfully copied to the target DVD discs the DVD Duplicator automatically ejects the discs C With the default setting if the copy operation fails the failed target DVD disc remains in the target drive To remove the failed DVD disc press the eject button on the target drive and retrieve the disc Then press the eject button again to retract the disc tray You can change the default settings by using the Advanced Setup menu See 12 Advanced Setup Adv Setup on page 20 12 TEAC Tower DVD Duplicator User s Manual Chapter 3 Tower DVD Duplicator Functions The Tower DVD Duplicator features 12 functions Copy Test Test Copy Verify Compare Prescan Disc Info Select Source Image Edit Track Setup and Advanced Setup Each function is explained below 1 Copy The Copy function enables you to copy data from a source DVD or a partition on the internal hard disk if your Tower DVD Duplicator features a factory installed hard disk drive For more information refer to Basic Operation on page 8 To copy data to one of more DVD R discs follow the steps below 1 Switch to function 1 Copy by pressing the Q button Ins
24. l from the shipping box Note Please keep the original box and packaging materials for use in the event of future storage or transportation of the unit Connect one end of the included power cable to the back of the DVD Duplicator Connect the other end of the power cable to a three prong receptacle AC outlet Caution Do not attempt to bypass the grounding plug Otherwise you risk damage to the unit and electrical shock Turn on the power to the DVD Duplicator by pressing the power button on the lower right hand side of the unit During initialization the DVD Duplicator performs a self test in which the unit s internal buffer is tested source and target drives are detected and the LCD display is tested Once the initialization is complete the DVD Duplicator is ready for use The LCD initially displays the Copy function by default rs o Figure 5 Copy Function on LCD Panel TEAC Tower DVD Duplicator User s Manual Basic Operation Basic Operation This section explains the basic operation of the DVD Duplicator Copying from the Optical DVD Source Drive Note The following instructions apply to all DVD Duplicator models 1 Place a source disc in the disc tray of the source drive Switch to function 1 Copy by pressing the button if necessary Place a blank DVD R disc into as many of the target drives as you desire then press the ENT button to start copying You do no
25. licator Unit Package Contents 0 0 0 0 cece eee 2 Figure 2 Front Panel of the DVD Duplicator Unit 0 000 000 eee 3 Figure 3 LCD Control Panel Js ere is cba 4 Figure 4 Rear Panel of the DVD Duplicator Unit 0 0 00 5 Figure 5 Copy Function on LCD Panel 0 Taia cece eee een 7 Figure 6 How to Handle Compact Discs DVD R and DVD RW 27 Figure 7 Ejecting the Disc Tr y coria ree ce vant ance chee UNE CN dk 28 TEAC Tower DVD Duplicator User s Manual v vi TEAC Tower DVD Duplicator User s Manual Chapter 1 Introduction Thank you for purchasing a TEAC Tower DVD Duplicator Note Q TEAC Tower DVD Duplicators are available in 1x3 one source drive and three target drives and Ix7 one source drive and seven target drives mod els with or without internal hard disk drives Please refer to Specifica tions on page 29 for detailed information on the model you purchased Q This User s Manual is intended for both 1x3 and 1x7 Tower DVD Duplica tor systems Operational instructions for all models are essentially the same The primary difference between models is the number of target drives and the inclusion of an optional hard disk drive Other minor differences between the models are described herein as necessary The TEAC Tower DVD Duplicator is a stand alone disc to disc DVD Duplicator system that does not require connection to a computer It can duplica
26. nction Itwill erase all data already loaded into disk partitions This function is reserved for factory use only The Verify HDD option is valid only on Tower DVD Duplicators that feature a factory installed hard disk drive The factory installed hard disk drive has already been partitioned and formatted and is ready for use 12 6 Burn in The Burn in function runs an emulate writer function continuously The disc in the target drive is ejected and re inserted automatically between each test cycle This function can be prepared to run continuously or specified to run from 1 to 1000 times 12 7 Update Firmware The Update Firmware function updates the firmware of the interface board via a CD or DVD disc The disc must contain the required data file and be inserted in the source drive The DVD Duplicator will locate the data and update its firmware automatically During the update do not turn off the power to the unit The update process is complete after the system resets automatically and displays the main menu 12 8 Compare Firmware The Compare Firmware function compares the current firmware version in the interface board to the update version in the CD or DVD disc 12 9 H W Diagnostic The H W Diagnostic function detects the devices connected to the interface board confirms functionality and displays information about the hardware on the LCD TEAC Tower DVD Duplicator User s Manual 21 12 10 Load Default The Load Def
27. pment You are responsible for all risk of damage to or loss of merchandise in transit to TEAC TEAC reserves the right to reject any merchandise that is not packaged and or marked as instructed herein You must pay any shipping charges if it is necessary to ship the product for service However if the necessary repairs are covered by the warranty we will pay the return shipping charges to any destination within the United States Whenever warranty service is required you must present a copy of the original dated sales receipt as proof of warranty coverage Please contact us at the addresses listed at the end of this warranty statement WHAT TEAC WILL PAY FOR We will pay all labor and material expenses for items covered by the warranty Payment of shipping charges is discussed in the next section of this warranty LIMITATION OF IMPLIED WARRANTIES ANY IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO THE LENGTH OF THIS WARRANTY ON UA RA un 30 TEAC Tower DVD Duplicator User s Manual Limited Warranty EXCLUSION OF DAMAGES TEAC S LIABILITY FOR ANY DEFECTIVE PRODUCT IS LIMITED TO REPAIR OR REPLACEMENT OF THE PRODUCT AT TEAC S OPTION TEAC SHALL NOT BE LIABLE FOR DAMAGES BASED UPON INCONVENIENCE LOSS OF USE OF THE PRODUCT LOSS OF TIME INTERRUPTED OPERATION OR COMMERCIAL LOSS LOST PROFITS OR ANY OTHER DAMAGES WHETHER INCIDENTAL CONSEQUENTIAL PUNITIVE OR OTHERWI
28. py them to a specific partition on the hard disk drive Note CD R discs support up to 80 minutes of audio Therefore the number of tracks that can be copied onto a single disc depends on the length of each individual track 10 3 Play Audio Track This function enables you to use the designated source drive as a music CD player If the DVD ROM drive does not feature a headphone jack change the source drive designation to one of the DVD RW drives using function 8 Select Source see page 14 You can connect standard multimedia speakers to the audio jack of the designated source drive The volume knob on the front of the drive controls the audio volume level The arrow buttons O O on the LCD panel enable you to skip to the next track forward or back 16 TEAC Tower DVD Duplicator User s Manual 10 4 Close Session 10 4 Close Session This function finalizes your CD R disc Once the CD R disc is finalized no more audio can be added to that disc 11 Setup The Setup menu includes a list of options that enable you to change the original default configuration Various settings are available under the Setup menu that control the operation of the DVD Duplicator However TEAC recommends that you use the original default settings for optimal operation 11 1 Language The DVD Duplicator LCD panel can display text in English and Spanish The Language function enables you to select the display language English is the default option
29. r systems that feature a factory installed hard disk drive The Image menu includes Load Delete Image Image Info Compare Image Select Image Image Src Drive and Image Format Info functions The data loaded onto the hard disk drive is called an image file 9 1 Load The factory installed hard disk drive was partitioned and formatted at the factory An alphabetical letter identifies each partition Each partition is approximately 5GB in capacity The number of partitions depends on the capacity of the hard disk drive The Load function enables you to transfer data from the DVD ROM drive or any DVD Writer drive to the current partition of the hard disk drive Note P A stands for partition A You can load as many disc images as the number of partitions available on the hard disk drive 9 2 Delete Image Use the Delete Image function to delete an image stored in a particular partition 9 3 Image Info Use the Image Info function to display basic information for an image file stored in a particular partition 9 4 Compare Image Use the Compare Image function to compare the contents of a source DVD ROM disc with the image file in the partition 9 5 Select Image The internal hard disk drive was partitioned and formatted at the factory An alphabetical letter identifies each partition Each partition is approximately 5GB in capacity The number of partitions depends on the capacity of the hard disk drive Use the Select Image function
30. ressed written permission of TEAC America Inc TEAC is a trademark of TEAC Corporation All other trademarks and registered trademarks are the property of their respective owners Piracy Statement Copying audio video or software without the permission of the copyright holder is illegal TEAC accepts no responsibility for copyright infringement or misuse of this equipment It is the sole responsibility of the user to ensure that the legal copyrights of the copyright owners are respected About This Manual This TEAC Tower DVD Duplicator User s Manual explains how to operate the TEAC Tower DVD Duplicator It is divided into the following chapters Chapter 1 Introduction This chapter describes the shipping package contents and introduces the TEAC Tower DVD Duplicator Chapter 2 Using the DVD Duplicator This chapter explains how to set up the DVD Duplicator It also details its basic copy operation Chapter 3 DVD Duplicator Functions This chapter explains all available functions of the DVD Duplicator Appendix A List of Functions Appendix A includes a complete list of all DVD Duplicator functions Appendix B LCD Messages Appendix B lists all messages that may appear on the LCD display Appendix C About DVD R and DVD RW Discs Appendix C contains information about handling loading and ejecting discs Appendix D Specifications Appendix D includes technical specifications for the TEAC Tower DVD Duplicator units Appendix E
31. t need to insert a DVD disc into every available target drive You can make fewer copies if you prefer The internal controller will automatically detect inserted discs and issue the record command to only those target drives that contain a blank disc When the copy operation is complete the DVD disc in each of the target drives will be ejected automatically a a Note With the default setting after a source disc has been successfully copied the DVD Duplicator automatically ejects the target DVD discs With the default setting ifthe copy operation fails the failed target DVD disc remains in the target drive To remove the failed DVD disc press the eject button on the target drive and retrieve the disc Press the eject button again to retract the disc tray You can change the default settings by using the Advanced Setup menu For more information see 12 Advanced Setup Adv Setup on page 20 TEAC Tower DVD Duplicator User s Manual Loading Data to and Copying from the Hard Disk Source Drive Loading Data to and Copying from the Hard Disk Source Drive Note The following instructions apply only to Tower DVD Duplicator models that feature a factory installed hard disk drive DVW DI3H and DVW D17H During initialization see Step 3 on page 7 the DVD Duplicator performs a self test to detect source drives The DVD ROM drive and hard disk drive will be detected as available source drives The DV
32. te a single master DVD to DVD media at up to 16X speeds resulting in an exact replica of a 4 7GB disc It can also duplicate discs to CD R media at up to 48X speeds The TEAC Tower DVD Duplicator is designed to perform DVD copying quickly and accurately The DVD Duplicator automatically identifies source DVD formats and replicates the content as required The TEAC Tower DVD Duplicator performs continuous copying with no waiting It is an ideal DVD Duplicator for the advanced user who requires speed and accuracy You can set up your TEAC Tower DVD Duplicator very quickly and easily There is no need to install any software There is no need to attach any cables to your computer The TEAC Tower DVD Duplicator functions entirely as a stand alone unit Caution Your TEAC Tower DVD Duplicator can operate on either 115VAC or 220VAC voltage Before you turn on the power to the unit be certain to select the correct voltage for your region by setting the AC Voltage Selector on the rear panel Failure to do so can result in damage to the unit For more information refer page 5 TEAC Tower DVD Duplicator User s Manual 1 DVD Duplicator Package Contents DVD Duplicator Package Contents Your TEAC DVD Duplicator package includes the following items see Figure 1 Q TEAC 1x3 or 1x7 Tower DVD Duplicator unit Q AC power cable Q TEAC Tower DVD Duplicator User s Manual this booklet
33. te through the various functions viewed on the LCD display Figure 3 LCD Control Panel The DVD Duplicator control panel features an LCD display and four buttons These buttons are described in the following table Press the Up arrow button to scroll up functions or menus Press the Down arrow button to scroll down functions or menus Press the ENT Enter button to execute a selected function Press the ESC Escape button to cancel a selected function or to return to the main menu O target drives Insert a blank disc into each target drive to make a copy of the source disc You can open the tray by pressing the eject button if the tray fails to open you can use the emergency eject mechanism You can close the tray by pressing the eject button Note TEAC strongly recommends that you do not push the tray in to close it Please press the eject button to eject or retract the tray power switch Use the power switch to turn the power to the DVD Duplicator unit on and off O LED power indicator The LED power indicator will be continuously lit when the DVD Duplicator power is on 4 TEAC Tower DVD Duplicator User s Manual Rear Panel Rear Panel Figure 4 illustrates the rear panel of the DVD Duplicator unit GO fe c S f 9 E el Ci 6 cooling fans O e Z e EZ e EN e 7 AC voltage ifr eS O dl lt gt
34. ting from accident misuse abuse or neglect Damage resulting from failure to follow instructions contained in your user s manual Damage occurring during shipment of the product claims must be presented to the carrier Damage resulting from repair or attempted repair by anyone other than TEAC Service Department Damage resulting from modification or attempted modification of product not authorized by TEAC 7 Damage resulting from causes other than product defects including lack of technical skill competence or experience of the user 8 Damage to any unit that has been altered or on which the serial number has been defaced modified or removed 9 Damage or malfunction resulting from installation and cabling 10 For wireless configurations TEAC cannot be responsible for interference or operation in locations that restrict range 11 Damage to or from interconnected network equipment 12 Data integrity or loss of data HOW YOU CAN GET WARRANTY SERVICE Please contact the TEAC service department for a Return Authorization number before shipping unit s to TEAC Information required for R A request should include your name and or company name telephone number TEAC model version and serial number s Return Authorization R A number must be clearly marked on the outside of each carton shipped to TEAC Return merchandise must be packed in original shipping containers or otherwise packed adequately to prevent damage in shi
35. to select an image file that is stored in a specific partition on the hard disk drive 9 6 Image Src Drive Use the Image Src Drive function to select the DVD ROM drive or a DVD Writer drive as the source from which you can load data into a particular partition as an image file TEAC Tower DVD Duplicator User s Manual 15 9 7 Image Format Info 9 7 Image Format Info The partitions on the hard disk drive can be configured to store a CD 1GB DVD 5GB or a Double Layer DL 10GB image The factory partitions the hard disc drive for DVD images at 5GB per partition Use the Image Format Info function to verify this setting 10 Edit Track for CD only The Edit Track functions enable you to create and copy a collection of songs from different audio discs Note The CD G value must be set to OFF before you can use the Track Extraction feature For more information refer to 12 Advanced Setup Adv Setup on page 20 10 1 CD to CD Edit The CD to CD Edit function enables you to select specific tracks from various audio discs combine them to create a collection of songs and copy the collection to blank CD R CD RW discs Note CD R discs support up to 80 minutes of audio Therefore the number of tracks that can be copied onto a single disc depends on the length of each individual track 10 2 CD to HDD The CD to HDD function enables you to select one or more tracks from an audio CD ROM disc and co
36. u should make changes only after you become completely familiar with the functions in this menu To enter Advanced Setup mode press the ESC button for two 2 seconds 12 1 UnderRun Protect The UnderRun Protect setting turns Buffer UnderRun Protection on or off The default setting is ON 12 2 Overburn The Overburn setting turns the Overburn function in the target drive on or off The default setting is OFF 12 3 Read Error Skip The Read Error Skip setting controls error skipping during reading of the source disc If the setting is OFF and an error is detected the target drive stops and displays the read error message If the setting is ON no messages will be displayed if an error occurs The copy operation will be completed and the copy will include all errors detected during the process The default setting is OFF 20 TEAC Tower DVD Duplicator User s Manual 12 4 Format HDD 12 4 Format HDD For factory use only please do NOT use this function Warning Do not run this function Itwill erase all data already loaded into disk partitions This function is reserved for factory use only The Format HDD option is valid only on Tower DVD Duplicators that feature a factory installed hard disk drive The factory installed hard disk drive has already been partitioned and formatted and is ready for use 12 5 Verify HDD For factory use only please do NOT use this function Warning Do not run this fu
37. utton Sound setting turns the button sound on or off The default setting is ON 11 15 Device Info The Device Info function displays information for both the source and target drives 11 16 System Info The System Info function displays information for the interface board 11 17 Quick Erase The Quick Erase function performs a Quick Erase on DVD RW discs 11 18 Full Erase The Full Erase function performs a Full Erase on DVD RW discs This function takes longer than the Quick Erase 11 19 Auto Close Tray The Auto Close Tray setting function closes the DVD writer s tray automatically after the recording is completed and the disc has been ejected It is related to function 11 5 Auto Start Drive TEAC Tower DVD Duplicator User s Manual 19 11 20 Quick Compare If you have not set any DVD writer to copy using function 11 5 the Auto Close Tray function will be invalid If function 11 5 is valid you can set for the writer s tray to close automatically after copying finishes You can specify tray closure to occur within 5 to 50 seconds 11 20 Quick Compare With the Quick Compare function you can specify a comparison of the source and the copied target discs in increments of 1byte through 100MB 11 21 Audio Burn Speed Use the Audio Burn Speed function to specify the write speed at which audio CDs will be recorded 12 Advanced Setup Adv Setup The Advanced Setup functions enable you to modify the system configuration Yo
Download Pdf Manuals
Related Search