Smeg KAP900X cooker hood
Contents
1. Biax neon lamps G23 11W lamp Once the fixture has been removed remove the biax lamp from its seat and support Put a new lamp in performing the same operations backwards Neon lamp 15 18W neon tube To reach the neon tube unscrew the glass framework screws Rotate the tube 90 degrees and remove the neon lamp Install the new neon tube and put the glass framework back EN 07 WARRANTY AND TECHNICAL ASSISTANCE SERVICE The hood packaging includes together with this operating and maintenance booklet the Smeg Warranty Booklet Please read the Smeg Warranty Booklet for complete information about the warranty N B bulbs and filters are not covered by your warranty In the case of failure please call Customer Service 0870 9909907 and provide the following data The model indicated inside the hood fig 7 Your full address Your telephone number Information on the kind of failure Your proof of purchase EN 082. BLE IF THE ABOVE INSTRUCTIONS ARE NOT FOLLOWED OPERATION This appliance has been designed to work as a DUCTING hood evacuation of the air or RECYCLING hood recycling of the filtered air e DUCTED MODE In order to use the hood in the ducted mode connect the motor intake by means of a suitable ducting hose not less than 120mm diameter directly to the external fumes outlet Note Remove any carbon filters e RECIRCULATION MODE If it is not possible to discharge fumes outside the hood can be used to filter and recycle the air This way air and fumes are filtered by the anti odour carbon filters and recirculated through the aerating grids on the sides of chimney EN 01 INSTALLATION INSTRUCTIONS The hood is supplied with all the necessary accessories for installation The minimum distance between the cooker and the lower part of the hood must be 750 mm for gas cookers and 650 mm for electric cookers Fig 1 The hood is supplied with a motor intake Fig 2 If it has not been assembled by the manufacturer you can assemble it using the supplied screws for type 1 or pushing for type 2 If the motor intake is equipped with a non return valve make sure it opens and closes perfectly The following instructions will assist installation a The hood should be centred with respect to the cooker b The hood is supplied with two supports hooks a Fig 3 or bracket b that need to be fixed to the wall by means of w
3. ELECTROMECHANICAL PUSHBUTTONS Light ON OFF Button O Motor OFF button xy On speed adjustment button gt WITH KNOBS Two position Knob A to turn on off the light 0 1 Four position Knob B 0 Motor OFF 1 2 3 Speed adjustment EN 04 s Smeg gt ELECTRONIC PUSHBUTTONS 5 Os Lights ON OFF Le C D 0 OFF 1 speed ge OM 2 3 4 a O C 2 5 4 Speed adjustment Filters reset button OPTIONAL FUNCTIONS AUTO POWER OFF TIMER Pushing one of the speed adjustment buttons 2 3 4 twice you will activate the Auto power off timer function that turns the motor and light off after 10 mins The activation of such function is signalled by the blinking LED above the pressed button FILTERS CLEANING WARNING When all the 4 LEDs blink at the same time which Is programmed to happen every 100h of operation the user is required to clean replace the filters Pressing the Reset button the 100h count will start again Note Pressing the reset button accidentally before the end of the 100h cycle does not reset the filters cleaning memory It is recommended that grease filters are cleaned every 100h and active carbon filters are replaced every 200h CLEANING AND MAINTENANCE Before performing any cleaning and or maintenance operation always disconnect the hood from the mains supply Regular cleaning will ensure a good performance and extend the working life of the hood Special attention should be
4. all anchors The L1 holes for these supports are on the back of the hood fig 4 c Remove the anti grease filters put the hood on the wall and mark the position of the holes for the supports hooks d Drill the two previously marked holes after removing the hood from the wall e Fix the two supports hooks to the wall f Mark the L2 holes on the wall to fix the hood safely fig 4 Drill and put the anchors in the holes g Hang the hood on to the supports hooks fig 5 and level by means of the adjusting screw fig 3 h Fix the hood safe by tightening both wall anchors Ducted mode or Recirculation mode installation Ducted mode In the ducted mode connect the motor outlet to the fumes outlet duct not less than 120mm diameter Warning if the hood is equipped with an active carbon filter it must be removed see page 7 02 Pi LPL LE eiz smeg Recirculation mode Leave the motor intake free Install the active carbon filters as shown in page 6 Warning if the hood is not supplied with an active carbon filter it is necessary to buy it separately and assemble it before using the hood i Chimneyassembly Adjust the two telescopic chimneys to the required length fig 6 Secure the chimneys by tightening the two H screws Place the chimney group on the top side of the hood carefully Put the chimney bracket K on the B chimney fig 6 Mark the holes on the wall for fixing the chimney brack
5. eizesmeg WAS Read the instructions carefully before installing and or using the hood e Before connecting make sure that the mains voltage corresponds to the voltage on the rating plate inside the hood see fig 7 e Once you remove the appliance from its packaging make sure it is intact If the product is damaged do not use it and contact the Smeg assistance network e It is recommended that a qualified technician performs installation and adjustment operations e The minimum distance between the cooker and the lower part of the hood must be 750mm for gas cookers and 650 mm for electric cookers e Before carrying out any kind of maintenance or cleaning disconnect the hood from the mains supply e Inspect and clean the filters thoroughly and in accordance with the intervals suggested by the manufacturer e Do not cook or fry in a way that could result in flames being sucked into the hood and causing a fire e The hood surface can be cleaned with a damp cloth and a non bleach liquid detergent e Make sure the room is properly ventilated when using the hood and other gas appliances at the same time e Comply with the regulations on air discharge when operating the hood e The extracted air must not be routed into a duct used to discharge fumes of gas operated appliances e This appliance must not be used by children without an adult supervision and disabled people may require assistance e THE MANUFACTURER CANNOT BE HELD RESPONSI
6. et to the wall Remove the chimney set drill and fix the support bracket to the wall by means of wall anchors Put the chimney group back in place and fix it to the hood with the Z screws and to the chimney bracket with the L screws as shown in figure 6 ELECTRICAL CONNECTION It is recommended that all electrical connection operations are performed by a qualified technician The appliance is supplied WITHOUT A PLUG It is therefore necessary to fix a plug to the cable or hard wire direct to a spur The plug and fuse must be in accordance with the rating plate inside the hood Then connect it to a nearby easily reachable socket in accordance with the rules in force In the case of a direct connection to the mains supply it is necessary to put a switched spur between the appliance and the mains supply The switch must be suitable for the load compliant with the rules in force and must have a minimum contact opening of not less than 3mm 03 e Smeg OPERATING INSTRUCTIONS V CONTROL PANEL In order to achieve the best performance it is recommended to start the hood a few minutes before starting cooking and keep it on for at least 15 minutes after finishing cooking or after all fumes and odours have disappeared To start the hood identify your type of control panel and follow the instructions gt SLIDER Key A to turn on off the hood s light Four position Cursor B 0 Off 1 2 3 On Speed adjustment gt
7. given to the grease filters and carbon filters for recycling hoods only Note An excess of grease in the filter as well as affecting the performance of the hood can also be a fire risk EXTERNAL CLEANING External and internal cleaning of the hood should be performed with a damp cloth and a non bleach liquid detergent absolutely avoiding solvents or abrasive substances It is advisable to use specific products following their instructions When cleaning the steel of the hood we suggest rubbing in the same direction as the grain EN 05 METAL FILTERS CLEANING eizesmeg Special attention should be reserved to the metal grease filters An excess of grease in the filter as well as affecting the performance of the hood can also be a fire risk To avert fires the filters must be cleaned regularly at least once a month or more frequently in the case of a heavy use of the appliance According to your hood s model remove one filter at a time as shown in these pictures Wash the filters thoroughly with a non bleach detergent either by hand or machine Re assemble the filters making sure that the handle faces the outside of the hood CARBON FILTERS REPLACEMENT For recirculated version only EN The carbon filters can only retain odours for a limited period of time They cannot be washed therefore it is recommended they are replaced at least once every six months or more frequently in the case of a heavy use
8. of the appliance Before starting make sure the hood is disconnected from the mains supply To reach the active carbon filters it is necessary to remove the metal filters as shown above Use the pictures to find the carbon filter kit of your hood Round filter simply rotate the filters 90 degrees as shown in fig A and then remove them from their seats Spring held cartridge filter fig B press enough to overcome the spring s resistance and remove the filter Cartridge filter with bracket and threaded knob fig C unscrew the knob remove the locking bracket and then remove the active carbon filter Re assemble the carbon and metal filters by reversing the procedure Note only for the electronic controlled hood reset the filter cleaning warning by pressing the Filter reset button 06 LIGHTS REPLACEMENT Before performing any cleaning and or maintenance operation disconnect the hood from the mains supply According to the model the hood can be equipped with different kind of lighting such as incandescent halogen and neon lamps a Incandescent lamps E14 40W 230V lamps To replace them remove the transparent fixture from the control panel unscrew the lamp and screw in the new one Halogen lamps G4 20W 12V lamps To replace the lamp use a screwdriver to remove the glass supporting ring Then remove the old lamp and insert the new one Put the glass back securing it with the ring
Download Pdf Manuals
Related Search