Home

Honeywell 3800gPDF USB Kit Negro

Contents

1. 7 13 Check Digits Required 7 13 Code 11 Message Length 7 14 Code 128 7 14 ISBT 128 Concatenation 7 14 Code 128 Message Length 7 15 Code 128 Code Page 7 15 Code 128 Function Code Transmit 7 15 Telepen 7 15 Telepen Output 7 16 Telepen Message Length 7 16 UPC A 7 17 UPC A Check Digit 7 17 UPC A Number System 7 17 UPC A Addenda 7 18 UPC A Addenda Required 7 18 UPC A Addenda Separator 7 18 v UPC A EAN 13 with Extended Coupon Code 7 19 UPC E 7 19 UPC E0 and UPC E1 7 19 UPC E0 and UPC E1 Expand 7 20 UPC E0 and UPC E1 Addenda Requir
2. 4 6 Chapter 5 Data Formatting Data Format Editor Introduction 5 1 To Add a Data Format 5 1 Other Programming Selections 5 2 Data Format Editor Commands 5 2 Data Format Editor 5 4 Data Formatter 5 5 Alternate Data Formats 5 5 Chapter 6 Secondary Interface 3800g Models 6 1 Enabling the Secondary Interface 6 1 Secondary RS 232 Connection 6 1 Secondary Trigger Mode 6 2 Hands Free Time Out 6 2 Chapter 7 Symbologies Introduction 7 1 All Symbologies 7 2 Message Length 7 2 Codabar 7 3 Codabar Start Stop Characters 7 3 Codabar Check Character 7 3 Codabar Concatenation
3. 7 35 Label Code 3800gHD 3800gPDF only 7 36 TCIF Linked Code 39 TLC39 3800gHD 3800gPDF only 7 36 Chapter 8 Interface Keys Keyboard Function Relationships 8 1 Supported Interface Keys 8 3 Chapter 9 Utilities To Add a Test Code I D Prefix to All Symbologies 9 1 Show Software Revision 9 1 Show Data Format 9 1 Resetting the Standard Product Defaults 9 1 Temporary Visual Xpress Configuration 9 2 Chapter 10 Visual Xpress Visual Xpress Introduction 10 1 Installing Visual Xpress from the Web 10 2 Chapter 11 Serial Programming Commands vii Conventions 11 1 Menu Command Syntax 11 1 Query Commands 11 2 Concatenation of Multiple Commands 11 2 Responses 11 2 Examples of Query Commands 11 3 Trigger Commands 11 4 Resetting the Standard Product Defaults
4. 7 27 GS1 DataBar Expanded 7 27 GS1 DataBar Expanded Message Length 7 28 China Post Code 7 28 Korea Post Code 7 29 Korea Post Message Length 7 29 PosiCode 7 29 PosiCode Message Length 7 30 vi Trioptic Code 7 30 Codablock F 7 31 Codablock F Message Length 7 31 Code 16K 7 31 Code 16K Message Length 7 32 Code 49 7 32 Code 49 Message Length 7 33 PDF417 3800gHD 3800gPDF only 7 33 PDF417 Message Length 7 33 MicroPDF417 3800gHD 3800gPDF only 7 34 MicroPDF417 Message Length 7 34 GS1 Composite Codes 7 34 UPC EAN Version 7 35 GS1 Composite Code Message Length 7 35 GS1 Emulation
5. 7 4 Codabar Message Length 7 5 iv Code 39 7 5 Code 39 Start Stop Characters 7 5 Code 39 Check Character 7 5 Code 39 Message Length 7 6 Code 39 Append 7 6 Code 32 Pharmaceutical PARAF 7 7 Full ASCII 7 7 Code 39 Code Page 7 8 Interleaved 2 of 5 7 8 Check Digit 7 8 Interleaved 2 of 5 Message Length 7 9 Code 93 7 10 Code 93 Message Length 7 10 Code 93 Code Page 7 10 Straight 2 of 5 Industrial three bar start stop 7 11 Straight 2 of 5 Industrial Message Length 7 11 Straight 2 of 5 IATA two bar start stop 7 11 Straight 2 of 5 IATA Message Length 7 12 Matrix 2 of 5 7 12 Matrix 2 of 5 Message Length 7 12 Code 11
6. 3800g 3800gHD 3800gPDF General Purpose Handheld Linear Imager User s Guide Disclaimer Honeywell International Inc HII reserves the right to make changes in speci fications and other information contained in this document without prior notice and the reader should in all cases consult HII to determine whether any such changes have been made The information in this publication does not repre sent a commitment on the part of HII HII shall not be liable for technical or editorial errors or omissions contained herein nor for incidental or consequential damages resulting from the furnish ing performance or use of this material This document contains proprietary information that is protected by copyright All rights are reserved No part of this document may be photocopied repro duced or translated into another language without the prior written consent of HII 2006 2009 Honeywell International Inc All rights reserved Other product names or marks mentioned in this document may be trademarks or registered trademarks of other companies and are the property of their respective owners Web Address www honeywell com aidc i Chapter 1 Getting Started About This Manual 1 1 Unpacking the Imager 1 1 3800g Models 1 1 Connecting the Imager with
7. 13 4 14 1 14 Customer Support Technical Assistance If you need assistance installing or troubleshooting your device please call your distributor or the nearest technical support office North America Canada Telephone 800 782 4263 Fax number 315 554 6705 E mail natechsupport honeywell com Latin America Telephone 803 835 8000 Telephone 800 782 4263 E mail latechsupport honeywell com Brazil Telephone 55 21 3535 9100 Fax 55 21 3535 9105 E mail brsuporte honeywell com Mexico Telephone 803 835 8000 E mail latechsupport honeywell com Europe Middle East and Africa Telephone 31 0 40 7999 393 Fax 31 0 40 2425 672 E mail eurosupport honeywell com Asia Pacific Telephone Hong Kong 852 3188 3485 or 2511 3050 Telephone China 86 21 6361 3818 E mail aptechsupport honeywell com Japan Telephone 813 3839 8511 E mail aptechsupport honeywell com Malaysia Telephone 603 6201 7020 E mail aptechsupport honeywell com Online Technical Assistance You can also access technical assistance online at www honeywell com aidc 14 2 Product Service and Repair Honeywell International Inc provides service for all its products through service centers throughout the world To obtain warranty or non warranty service contact the appropriate location below to obtain a Return Material Authorization number RMA before returning the product North America
8. The standard Label Code is used in library situations Default Off TCIF Linked Code 39 TLC39 3800gHD 3800gPDF only This code is a composite code since it has a Code 39 linear component and a MicroPDF417 stacked code component All barcode readers are capable of reading the Code 39 linear component The MicroPDF417 component can only be decoded if TLC39 On is selected The linear component may be decoded as Code 39 even if TLC39 is off Default Off On Off On Off 8 1 8 Interface Keys Keyboard Function Relationships The following Keyboard Function Code Hex ASCII Value and Full ASCII CTRL relationships apply to all terminals that can be used with the imager Refer to page 2 6 enable Control ASCII mode Function Code HEX ASCII Value Full ASCII CTRL NUL 00 2 SOH 01 A STX 02 B ETX 03 C EOT 04 D ENQ 05 E ACK 06 F BEL 07 G BS 08 H HT 09 I LF 0A J VT 0B K FF 0C L CR 0D M SO 0E N SI 0F O DLE 10 P DC1 11 Q DC2 12 R DC3 13 S DC4 14 T NAK 15 U SYN 16 V ETB 17 W CAN 18 X EM 19 Y SUB 1A Z ESC 1B FS 1C GS 1D RS 1E 6 US 1F 8 2 The last five characters in the Full ASCII CTRL column 6 apply to US only The following chart indicates the equivalents of these five characters for different countries Country Codes United States 6 Belgium lt 6 Scan
9. 11 4 Menu Commands 11 5 Chapter 12 Product Specifications 3800g Product Specifications 12 1 3800gHD 3800gPDF Product Specifications 12 2 Chapter 13 Maintenance Repairs 13 1 Maintenance 13 1 Cleaning the Device 13 1 Inspecting Cords and Connectors 13 1 Replacing the Interface Cable 13 2 Troubleshooting 13 2 Chapter 14 Customer Support Technical Assistance 14 1 Online Technical Assistance 14 1 Product Service and Repair 14 2 Online Product Service and Repair Assistance 14 2 Limited Warranty 14 3 Appendix A Symbology Chart A 1 ASCII Conversion Chart Code Page 1252 A 3 Code Page Mapping of Printed Bar Codes A 5 viii Product Agency Compliance USA FCC Part 15 Subpart B Class B This device complies with part 15 of the FCC Rules Operation is subject to the following two condition
10. 3 Tied to supply power 4 Supply ground 5 Terminal clock 6 Terminal data 7 Supply power input Refer to tables on page 12 1 8 Keyboard data 9 Keyboard clock 10 12 4 Standard Cable Pinouts Serial Output 10 Pin RJ41 Modular Plug connects to the imager handle 1 2 Cord shield 3 Prog 1 Tied to supply power for primary cable 4 Supply ground 5 Receive data Serial data to imager 6 Transmit data Serial data from imager 7 Supply power input Refer to tables on page 12 1 8 Request to send data 9 Clear to send data 10 12 5 Standard Cable Pinouts USB 10 Pin Modular Plug connects to the imager handle 1 2 Data 3 Tied to supply power 4 Supply ground 5 6 7 5 volt supply power input 8 9 10 Data 12 6 13 1 13 Maintenance Repairs Repairs and or upgrades are not to be performed on this product These ser vices are to be performed only by an authorized service center Please see Customer Support on page 14 1 for further information Maintenance The 3800g provides reliable and efficient operation with a minimum of care Although specific maintenance is not required the following periodic checks ensure dependable scanner operation Cleaning the Device Reading performance may degrade if the scanner s window is not clean If the window is visibly dirty or if the scanner isn t operating well clean the window with a soft cloth or lens tissue dampened with water or a
11. Telephone 800 782 4263 Fax 803 835 8012 E mail naservice honeywell com Latin America Telephone 803 835 8000 Telephone 800 782 4263 Fax 239 263 9689 E mail laservice honeywell com Brazil Telephone 55 21 3535 9100 Fax 55 21 3535 9105 E mail brservice honeywell com Mexico Telephone 52 55 5203 2100 Fax 52 55 5531 3672 E mail mxservice honeywell com Europe Middle East and Africa Telephone 31 0 40 2901 633 Fax 31 0 40 2901 631 E mail euservice honeywell com Asia Pacific Telephone 852 2511 3050 Fax 852 2511 3557 E mail apservice honeywell com Japan Telephone 813 3839 8511 Fax 813 3839 8519 E mail apservice honeywell com Online Product Service and Repair Assistance You can also access product service and repair assistance online at www honeywell com aidc 14 3 Limited Warranty Honeywell International Inc HII warrants its products and optional accesso ries to be free from defects in materials and workmanship and to conform to HII s published specifications applicable to the products purchased at the time of shipment This warranty does not cover any HII product which is i improp erly installed or used ii damaged by accident or negligence including failure to follow the proper maintenance service and cleaning schedule or iii dam aged as a result of A modification or alteration by the purchaser or other party B excessive voltage
12. leaving cursor pointing to xx character Syntax F8xx xx stands for the hex value for an ASCII code see ASCII Conversion Chart Code Page 1252 on page A 3 F9 Search back for xx character from current cursor position leaving cursor pointing to xx character Syntax F9xx xx stands for the hex value for an ASCII code see ASCII Conversion Chart Code Page 1252 on page A 3 E6 Search ahead for the first non xx character from the current cursor posi tion leaving cursor pointing to non xx character Syntax E6xx xx stands for the hex value for an ASCII code see ASCII Conversion Chart Code Page 1252 on page A 3 E7 Search back for the first non xx character from the current cursor position leaving cursor pointing to non xx character Syntax E7xx xx stands for the hex value for an ASCII code see ASCII Conversion Chart Code Page 1252 on page A 3 Miscellaneous Commands FB Suppress all occurrences of up to 15 different characters starting at the current cursor position as the cursor is advanced by other commands When the FC command is encountered the suppress function is termi nated The cursor is not moved by the FB command Syntax FBnnxxyy zz where nn is a count of the number of suppressed characters in the list 5 4 and xxyy zz is the list of characters to be suppressed xx stands for the hex value for an ASCII code see ASCII Conversion Chart Code Page 1252 on p
13. symbol is normally transmitted at the beginning of the scanned data but the unit can be programmed so it will not transmit it Default On On Off On Off Off On 7 18 UPC A Addenda This selection adds 2 or 5 digits to the end of all scanned UPC A data Default Off for both 2 Digit and 5 Digit Addenda UPC A Addenda Required When Addenda Required is set to on the imager will only read UPC A bar codes that have addenda Default Not Required UPC A Addenda Separator When this feature is on there is a space between the data from the bar code and the data from the addenda When turned off there is no space Default On 5 Digit Addenda Off 5 Digit Addenda On 2 Digit Addenda Off 2 Digit Addenda On Not Required Required Off On 7 19 UPC A EAN 13 with Extended Coupon Code Use the following codes to enable or disable UPC A and EAN 13 with Extended Coupon Code Default On UPC E lt Default All UPC E Settings gt UPC E0 and UPC E1 Most U P C bar codes lead with the 0 number system For these codes use the UPC E0 selection If you need to read codes that lead with the 1 number sys tem use the UPC E1 selection Default On UPC E0 and Off UPC E1 On Off UPC E0 On UPC E0 Off UPC E1 On UPC E1 Off 7 20 UPC E0 and UPC E1 Expand UPC E Expand expands the UPC E code to the 12 digit UPC A format Default Off UPC E0 and UPC
14. 11 Symbologies All Symbologies All Symbologies Off ALLENA0 7 2 All Symbologies On ALLENA1 7 2 Codabar Default All Codabar Settings CBRDFT 7 3 Codabar Off CBRENA0 7 3 On CBRENA1 7 3 Codabar Start Stop Char Don t Transmit CBRSSX0 7 3 Transmit CBRSSX1 7 3 Codabar Check Char No Check Char CBRCK20 7 4 Validate But Don t Trans mit CBRCK21 7 4 Validate and Transmit CBRCK22 7 4 Codabar Concatena tion Off CBRCCT0 7 4 On CBRCCT1 7 4 Require CBRCCT2 7 4 Codabar Message Length Minimum 2 60 4 CBRMIN 7 5 Maximum 2 60 60 CBRMAX 7 5 Code 39 Default All Code 39 Settings C39DFT 7 5 Code 39 Off C39ENA0 7 5 On C39ENA1 7 5 Code 39 Start Stop Char Don t Transmit C39SSX0 7 5 Transmit C39SSX1 7 5 Code 39 Check Char No Check Char C39CK20 7 6 Validate But Don t Transmit C39CK21 7 6 Validate and Transmit C39CK22 7 6 Code 39 Message Length Minimum 0 48 0 C39MIN 7 6 Maximum 0 48 48 C39MAX 7 6 Selection Setting Indicates default Serial Command Indicates a numeric entry Page 11 12 Code 39 Append Off C39APP0 7 6 On C39APP1 7 6 Code 32 Pharmaceuti cal PARAF Off C39B320 7 7 On C39B321 7 7 Code 39 Full ASCII Off C39ASC0 7 8 On C39ASC1 7 8 Interleaved 2 of 5 Default All Interleaved 2 of 5 Settings I25DFT 7 8 Interleaved 2 of 5 Off I25E
15. 196 C4 228 E4 133 85 165 A5 197 C5 229 E5 134 86 166 A6 198 C6 230 E6 135 87 167 A7 199 C7 231 E7 136 88 168 A8 200 C8 232 E8 137 89 169 A9 201 C9 233 E9 138 8A 170 AA 202 CA 234 EA 139 8B 171 AB 203 CB 235 EB 140 8C 172 AC 204 CC 236 EC 141 8D 173 AD 205 CD 237 ED 142 8E 174 AE 206 CE 238 EE 143 8F 175 AF 207 CF 239 EF 144 90 176 B0 208 D0 240 F0 145 91 177 B1 209 D1 241 F1 146 92 178 B2 210 D2 242 F2 147 93 179 B3 211 D3 243 F3 148 94 180 B4 212 D4 244 F4 149 95 181 B5 213 D5 245 F5 150 96 182 B6 214 D6 246 F6 151 97 183 B7 215 D7 247 F7 152 98 184 B8 216 D8 248 F8 153 99 185 B9 217 D9 249 F9 154 9A 186 BA 218 DA 250 FA 155 9B 187 BB 219 DB 251 FB 156 9C 188 BC 220 DC 252 FC 157 9D 189 BD 221 DD 253 FD 158 9E 190 BE 222 DE 254 FE 159 9F 191 BF 223 DF 255 FF A 5 Code Page
16. 3800g take the following steps Check to make sure everything you ordered is present Save the shipping container for later storage or shipping Check for damage during shipment Report damage immediately to the carrier who delivered the carton 3800g Models Note The Honeywell 3800g imager may be used with many interfaces which are described in this User s Guide Refer to the chart below to determine the models that can be used with your interface Refer to Chapter 6 for programming information regarding Secondary Interfaces The chart below lists the 3800g imager models Models Primary Interfaces Secondary Interfaces 3800G04E 3800G14E TTL level RS 232 USB Key board wedge TTL level RS 232 3800G05E 3800G15E TTL level RS 232 IBM Retail USB Retail USB Keyboard wedge TTL level RS 232 3800GHD24E TTL level RS 232 USB Key board wedge TTL level RS 232 3800GPDF04E TTL level RS 232 USB Key board wedge TTL level RS 232 1 2 Connecting the Imager with USB Note Honeywell recommends connecting the imager end of the cable first and the host end second An imager can be connected to the USB port of a computer 1 Connect the appropriate interface cable to the imager and to the computer 2 The imager beeps 3 Verify the imager operation by scanning a bar code from the Sample Symbols in the back of this manual For additional USB programming and technical information refer t
17. AIM ID Modifiers m Code ID hex All Symbologies 0x99 Australian Post X0 A 0x41 Aztec Code zm 0 9 A C z 0x7A British Post X0 B 0x42 Canadian Post X0 C 0x43 China Post X0 Q 0x51 Chinese Sensible Code Han Xin Code X0 H 0x48 Codabar Fm 0 1 a 0x61 Codablock F Om 0 1 4 5 6 q 0x71 Code 11 H3 h 0x68 Code 128 Cm 0 1 2 4 j 0x6A Code 16K Km 0 1 2 4 o 0x6F Code 32 Pharmaceutical PARAF X0 lt 0x3C Code 39 supports Full ASCII mode Am 0 1 3 4 5 7 b 0x62 Code 49 Tm 0 1 2 4 l 0x6C Code 93 and 93i Gm 0 9 A Z a m i 0x69 Data Matrix dm 0 6 w 0x77 EAN 13 including Bookland EAN E0 d 0x64 EAN 13 with Add On E3 d 0x64 EAN 13 with Extended Coupon Code E3 d 0x64 EAN 8 E4 D 0x44 EAN 8 with Add On E3 D 0x44 GS1 Composite em 0 3 y 0x79 GS1 DataBar em 0 y 0x79 GS1 128 C1 I 0x49 Intelligent Mail Barcode X0 M 0x4D A 2 Note m represents the AIM modifier character Refer to International Technical Specification Symbology Identifiers for AIM modifier character details Prefix Suffix entries for specific symbologies override the universal All Symbologies 99 entry Interleaved 2 of 5 Im 0 1 3 e 0x65 Japanese Post X0 J 0x4A KIX Netherlands Post X0 K 0x4B Korea Post X0 0x3F Matrix 2 of 5 X0
18. JAN 8 Addenda Separator When this feature is on there is a space between the data from the bar code and the data from the addenda When turned off there is no space Default On MSI lt Default All MSI Settings gt MSI MSI Check Character Different types of check characters are used with MSI bar codes You can program the imager to read MSI bar codes with Type 10 check characters Default Validate Type 10 but Don t Transmit When Check Character is set to Validate and Transmit the imager will only read MSI bar codes printed with the specified type check character and will transmit this character at the end of the scanned data When Check Character is set to Validate but Don t Transmit the unit will only read MSI bar codes printed with the specified type check character but will not transmit the check character with the scanned data Off On On Off Validate Type 10 and Transmit Validate Type 10 but Don t Transmit 7 26 MSI Message Length Scan the bar codes below to change the message length Refer to Message Length on page 7 2 for additional information Minimum and Maximum lengths 4 48 Minimum Default 4 Maximum Default 48 Plessey Code lt Default All Plessey Code Settings gt Plessey Code Plessey Message Length Scan the bar codes below to change the message length Refer to Message Length on page 7 2 for additional information Minimum and Maximum lengths 4 48 Minimum De
19. Mapping of Printed Bar Codes Code pages define the mapping of character codes to characters If the data received does not display with the proper characters it may be because the bar code being scanned was created using a code page that is different from the one the host program is expecting If this is the case select the code page with which the bar codes were created The data characters should then appear properly Note The Code Page option is available for Code 39 Code 93 and Code 128 Code Page Standard Description 1 CP ISO646 2 Default ISO 2022 Automatic National Replacement Charac ters 3 CP Binary 82 ISO 2022 11 Swe Swedish Replacement Characters 83 ISO 2022 69 Fra French Belgium Replacement Characters 81 ISO 2022 25 Fra French Belgium Replacement Characters 84 ISO 2022 11 Ger German Replacement Characters 85 ISO 2022 11 Ita Italian Replacement Characters 86 ISO 2022 11 Swi Swiss Replacement Characters 87 ISO 2022 11 UK British Replacement Characters 88 ISO 2022 11 Dan Danish Replacement Characters 89 ISO 2022 11 Nor Norwegian Replacement Characters 90 ISO 2022 11 Spa Spanish Replacement Characters A 6 3800g 3800gHD 3800gPDF User s Guide Sample Symbols UPC A 0 123456 7890 Interleaved 2 of 5 Code 128 EAN 13 1234567890 Code 128 9 780330 290951 654 EAN 8 3210 5 456123 8 0 UPC E 3800g 3800gHD 3800gPDF User s Guide Sample Symbo
20. Terminal ID Save 2 2 Supported Terminals Terminal Model s Terminal ID DEC VT510 520 525 PC style 005 DEC VT510 520 525 DEC style LK411 104 Esprit 200 400 005 Heath Zenith PC AT 003 HP Vectra 003 IBM XT 001 IBM PS 2 25 30 77DX2 002 IBM AT PS 2 30 286 50 55SX 60 70 70 061 70 121 80 003 IBM 102 key 3151 3161 3162 3163 3191 3192 3194 3196 3197 3471 3472 3476 3477 006 IBM 122 key 3191 3192 3471 3472 007 IBM 122 key 3196 3197 3476 3477 3486 3482 3488 008 IBM 122 key 3180 024 IBM 122 key 3180 data entry keyboard 114 IBM DOS V 106 key PC amp Workstation 102 IBM SurePOS USB Handheld Imager 128 IBM SurePOS USB Tabletop Imager 129 IBM Thinkpad 360 CSE 340 750 097 IBM Thinkpad 106 IBM Thinkpad 365 755CV 003 I O 122 key 2676D 2677C 2677D 008 ITT 9271 007 Lee Data IIS 007 NEC 98XX Series 103 Olivetti M19 M200 001 Olivetti M240 M250 M290 M380 P500 003 RS 232 TTL 000 Silicon Graphics Indy Indigoll 005 Telex 88 key 078 078A 79 80 191 196 1191 1192 1471 1472 1476 1477 1483 025 Telex 88 key Data Entry Keyboard 112 Telex 102 key 078 078A 79 80 191 196 1191 1192 1471 1472 1476 1477 1483 045 2 3 Factory default setting Telex 122 key 078 078A 79 80 191 196 1191 1192 1471 1472 1476 1477 1482 1483 046 USB PC Keyboard 124 USB Mac Keyboard 125 USB C
21. USB 1 2 USB PC or Macintosh Keyboard 1 2 IBM SurePos 1 3 USB HID 1 3 USB Com Port Emulation 1 3 Plug and Play 1 4 Connecting the Imager When Powered by Host Keyboard Wedge 1 4 Keyboard Wedge Connection 1 5 Laptop Direct Connect 1 6 Connecting the Imager with RS 232 Serial Port 1 6 IBM 4683 Ports 5B 9B and 17 Interface 1 7 Reading Techniques 1 8 Reading PDF417 Bar Codes 1 8 Resetting the Standard Product Defaults 1 9 Chapter 2 Terminal Interfaces Terminal ID 2 1 Supported Terminals 2 2 Keyboard Country 2 4 Keyboard Style 2 5 Keyboard Modifiers 2 6 RS 232 Baud Rate 2 8 RS 232 Word Length Data Bits
22. VT 0B Tab Tab Tab FF 0C N A N A Delete CR 0D New Line New Line New Line SO 0E N A N A Insert SI 0F Escape Escape Escape DLE 10 F11 F11 F11 DC1 11 Insert Insert Home DC2 12 F13 F13 Print DC3 13 Back Space Back Space Back Space DC4 14 Back Tab Back Tab Back Tab NAK 15 F12 F12 F12 SYN 16 F1 F1 F1 ETB 17 F2 F2 F2 CAN 18 F3 F3 F3 EM 19 F4 F4 F4 SUB 1A F5 F5 F5 ESC 1B F6 F6 F6 FS 1C F7 F7 F7 GS 1D F8 F8 F8 RS 1E F9 F9 F9 US 1F F10 F10 F10 8 6 Supported Interface Keys ASCII HEX Apple Mac iMac Supported Keys NUL 00 Reserved SOH 01 Enter Numpad Enter STX 02 CAPS ETX 03 ALT make EOT 04 ALT break ENQ 05 CNTRL make ACK 06 CNTRL break BEL 07 RETURN BS 08 APPLE make HT 09 TAB LF 0A APPLE break VT 0B TAB FF 0C Del CR 0D RETURN SO 0E Ins Help SI 0F ESC DLE 10 F11 DC1 11 Home DC2 12 Prnt Scrn DC3 13 BACKSPACE DC4 14 LSHIFT TAB NAK 15 F12 SYN 16 F1 ETB 17 F2 CAN 18 F3 EM 19 F4 SUB 1A F5 ESC 1B F6 FS 1C F7 GS 1D F8 RS 1E F9 US 1F F10 DEL 7F BACKSPACE 9 1 9 Utilities To Add a Test Code I D Prefix to All Symbologies This selection allows you to turn on transmission of a Code I D before the decoded symbology See the Symbology Chart included in the Appendix A on page A 1 for the single character code that identifies each symbology This action first clea
23. beam No Read With No Read turned On the imager sends an NR to the host if you pull and release the trigger without reading a code e g bad bar code If No Read is turned Off the NR will not be sent to the host If you want a different notation than NR for example Error or Bad Code you can edit the output message using the Data Formatter page 5 5 The hex code for the No Read symbol is 9C Required On Not Required Off On Off On Off 3 13 Video Reverse Video Reverse is used to allow the imager to read bar codes that are inverted The Off bar code below is an example of this type of bar code Note If additional menuing is required Video Reverse must be disabled to read the menu bar codes and then re enabled after menuing is completed On Off 3 14 4 1 4 Data Editing Prefix Suffix Overview When a bar code is scanned additional information is sent to the host computer along with the bar code data This group of bar code data and additional user defined data is called a message string The selections in this section are used to build the user defined data into the message string Prefix and Suffix characters are data characters that can be sent before and after scanned data You can specify if they should be sent with all symbologies or only with specific symbologies The following illustration shows the break down of a message str
24. m 0x6D MaxiCode Um 0 3 x 0x7 8 MicroPDF417 Lm 3 5 R 0x52 MSI Mm 0 g 0x67 OCR MICR E 13 B o3 O 0x4F OCR SEMI Font o3 O 0x4F OCR US Money Font o3 O 0x4F OCR A o1 O 0x4F OCR B o2 O 0x4F PDF417 Lm 0 2 r 0x72 Planet Code X0 L 0x4C Plessey Code P0 n 0x6E Postal 4i UPU 4 State X0 N 0x4E Postnet X0 P 0x50 QR Code and Micro QR Code Qm 0 6 s 0x73 Straight 2 of 5 IATA Rm 0 1 3 f 0x66 Straight 2 of 5 Industrial S0 f 0x66 TCIF Linked Code 39 TLC39 L2 T 0x54 UPC A E0 c 0x63 UPC A with Add On E3 c 0x63 UPC A with Extended Coupon Code E3 c 0x63 UPC E E0 E 0x45 UPC E with Add On E3 E 0x45 UPC E1 obsolete X0 E 0x45 Symbology AIM ID Possible AIM ID Modifiers m Code ID hex A 3 ASCII Conversion Chart Code Page 1252 Note This table applies to U S style keyboards Certain characters may differ depending on your Country Code PC regional settings Dec Hex Char Dec Hex Char Dec Hex Char Dec Hex Char 0 00 NUL 32 20 64 40 96 60 1 01 SOH 33 21 65 41 A 97 61 a 2 02 STX 34 22 66 42 B 98 62 b 3 03 ETX 35 23 67 43 C 99 63 c 4 04 EOT 36 24 68 44 D 100 64 d 5 05 ENQ 37 25 69 45 E 101 65 e 6 06 ACK 38 26 amp 70 46 F 102 66 f 7 07 BEL 39 27 7
25. or current supplied to or drawn from the interface connec tions C static electricity or electro static discharge D operation under condi tions beyond the specified operating parameters or E repair or service of the product by anyone other than HII or its authorized representatives This warranty shall extend from the time of shipment for the duration published by HII for the product at the time of purchase Warranty Period Any defective product must be returned at purchaser s expense during the Warranty Period to HII factory or authorized service center for inspection No product will be accepted by HII without a Return Materials Authorization which may be obtained by contacting HII In the event that the product is returned to HII or its authorized service center within the Warranty Period and HII determines to its satisfaction that the product is defective due to defects in materials or workman ship HII at its sole option will either repair or replace the product without charge except for return shipping to HII EXCEPT AS MAY BE OTHERWISE PROVIDED BY APPLICABLE LAW THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER COVENANTS OR WARRANTIES EITHER EXPRESSED OR IMPLIED ORAL OR WRITTEN INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MER CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR NON INFRINGEMENT HII S RESPONSIBILITY AND PURCHASER S EXCLUSIVE REMEDY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPL
26. page A 3 F3 Send up to but not including ss character Search and Send starting from current cursor position leaving cursor pointing to ss character followed by xx key or function code Syntax F3ssxx ss and xx both stand for the hex values for ASCII codes see ASCII Conversion Chart Code Page 1252 on page A 3 F4 Send xx character nn times Insert leaving cursor in current cursor posi tion Syntax F4xxnn xx stands for the hex value for an ASCII code see ASCII Conversion Chart Code Page 1252 on page A 3 and nn is the numeric value 00 99 for the number of times it should be sent E9 Send all but the last nn characters starting from the current cursor posi tion Syntax E9nn nn is the numeric value 00 99 for the number of characters that will not be sent at the end of the message Move Commands F5 Move the cursor ahead nn characters from current cursor position Syntax F5nn nn stands for the numeric value 00 99 for the number of characters the cursor should be moved ahead F6 Move the cursor back nn characters from current cursor position Syntax F6nn nn stands for the numeric value 00 99 for the number of characters the cursor should be moved back F7 Move the cursor to the beginning of the data string Syntax F7 EA Move the cursor to the end of the data string Syntax EA Search Commands F8 Search ahead for xx character from current cursor position
27. the 3800g as a keyboard wedge interface to an IBM PC AT with a U S keyboard If you programmed the imager for a different terminal interface and you want to change to an IBM PC AT and compatibles keyboard wedge interface scan the bar code below Note The following bar code also programs a carriage return CR suffix IBM PC AT and Compatibles with CR suffix 1 6 Laptop Direct Connect For most laptops scanning the Laptop Direct Connect bar code allows opera tion of the imager in parallel with the integral keyboard The following Laptop Direct Connect bar code selects terminal ID 03 programs a carriage return CR suffix and turns on Emulate External Keyboard page 2 5 Connecting the Imager with RS 232 Serial Port 1 Turn off power to the terminal computer 2 Connect the appropriate interface cable to the imager Note For the imager to work properly you must have the correct cable for your type of terminal computer 3 Plug the serial connector into the serial port on your computer Tighten the two screws to secure the connector to the port 4 Connect the power supply and plug into an outlet 5 Turn the terminal computer power back on Note You will not hear a power up beep because the 3800g is factory defaulted to a USB connection You must scan the RS 232 Interface bar code below to enable RS 232 ability Laptop Direct Connect with CR suffix 1 7 All communication parameters between the imager and
28. the sequence editor with the following command line SEQBLK62999941FF6A999942FF69999943FF The breakdown of the command line is shown below SEQBLKsequence editor start command 62 code identifier for Code 39 9999 code length that must match for Code 39 9999 all lengths 41 start character match for Code 39 41h A FF termination string for first code 6A code identifier for Code 128 9999 code length that must match for Code 128 9999 all lengths 42 start character match for Code 128 42h B FF termination string for second code 69 code identifier for Code 93 9999 code length that must match for Code 93 9999 all lengths 43 start character match for Code 93 43h C FF termination string for third code A Code 39 B Code 128 C Code 93 3 11 To program the previous example using specific lengths you would have to count any programmed prefixes suffixes or formatted characters as part of the length If you use the example on page 3 10 but assume a lt CR gt suffix and specific code lengths you would use the following command line SEQBLK62001241FF6A001342FF69001243FF The breakdown of the command line is shown below SEQBLK sequence editor start command 62 code identifier for Code 39 0012 A Code 39 sample length 11 plus CR suffix 1 12 41 start character match for Code 39 41h A FF termination string for first code 6A code identifier for Code 128 0013 B Code 1
29. 1 47 G 103 67 g 8 08 BS 40 28 72 48 H 104 68 h 9 09 HT 41 29 73 49 l 105 69 i 10 0A LF 42 2A 74 4A J 106 6A j 11 0B VT 43 2B 75 4B K 107 6B k 12 0C FF 44 2C 76 4C L 108 6C l 13 0D CR 45 2D 77 4D M 109 6D m 14 0E SO 46 2E 78 4E N 110 6E n 15 0F SI 47 2F 79 4F O 111 6F o 16 10 DLE 48 30 0 80 50 P 112 70 p 17 11 DC1 49 31 1 81 51 Q 113 71 q 18 12 DC2 50 32 2 82 52 R 114 72 r 19 13 DC3 51 33 3 83 53 S 115 73 s 20 14 DC4 52 34 4 84 54 T 116 74 t 21 15 NAK 53 35 5 85 55 U 117 75 u 22 16 SYN 54 36 6 86 56 V 118 76 v 23 17 ETB 55 37 7 87 57 W 119 77 w 24 18 CAN 56 38 8 88 58 X 120 78 x 25 19 EM 57 39 9 89 59 Y 121 79 y 26 1A SUB 58 3A 90 5A Z 122 7A z 27 1B ESC 59 3B 91 5B 123 7B 28 1C FS 60 3C lt 92 5C 124 7C 29 1D GS 61 3D 93 5D 125 7D 30 1E RS 62 3E gt 94 5E 126 7E 31 1F US 63 3F 95 5F _ 127 7F A 4 Dec Hex Char Dec Hex Char Dec Hex Char Dec Hex Char 128 80 160 A0 192 C0 224 E0 129 81 161 A1 193 C1 225 E1 130 82 162 A2 194 C2 226 E2 131 83 163 A3 195 C3 227 E3 132 84 164 A4
30. 13 On C11ENA1 7 13 Code 11 Check Digits Required 1 Check Digit C11CK20 7 13 2 Check Digits C11CK21 7 13 Code 11 Message Length Minimum 1 80 4 C11MIN 7 14 Maximum 1 80 80 C11MAX 7 14 Code 128 Default All Code 128 Settings 128DFT 7 14 Code 128 Off 128ENA0 7 14 On 128ENA1 7 14 ISBT Concatenation On ISBENA1 7 14 Off ISBENA0 7 14 Code 128 Message Length Minimum 0 80 0 128MIN 7 15 Maximum 0 80 80 128MAX 7 15 Code 128 Code Page Code 128 Code Page 128DCP 7 15 Code 128 Function Code Transmit Off 128FNX0 7 15 On 128FNX1 7 15 ISBT Concatenation Off ISBENA0 7 14 On ISBENA1 7 14 Selection Setting Indicates default Serial Command Indicates a numeric entry Page 11 14 Telepen Default All Telepen Settings TELDFT 7 16 Telepen Off TELENA0 7 16 On TELENA1 7 16 Telepen Output AIM Telepen Output TELOLD0 7 16 Original Telepen Output TELOLD1 7 16 Telepen Message Length Minimum 1 60 1 TELMIN 7 16 Maximum 1 60 60 TELMAX 7 16 UPC A Default All UPC A Settings UPADFT 7 17 UPC A Off UPAENA0 7 17 On UPAENA1 7 17 UPC A Check Digit Off UPACKX0 7 17 On UPACKX1 7 17 UPC A Number Sys tem Off UPANSX0 7 17 On UPANSX1 7 17 UPC A 2 Digit Addenda Off UPAAD20 7 18 On UPAAD21 7 18 UPC A 5 Digit Addenda Off UPAAD50 7 18 On UPAAD51 7 18 UP
31. 28 sample length 12 plus CR suffix 1 13 42 start character match for Code 128 42h B FF termination string for second code 69 code identifier for Code 93 0012 C Code 93 sample length 11 plus CR suffix 1 12 43 start character match for Code 93 43h C FF termination string for third code Output Sequence Editor Require Output Sequence When an output sequence is Required all output data must conform to an edited sequence or the image scanner will not transmit the output data to the host device When it s On Not Required the image scanner will attempt to get the output data to conform to an edited sequence but if it cannot the image scanner transmits all output data to the host device as is Enter Sequence Default Sequence 3 12 When the output sequence is Off the barcode data is output to the host as the image scanner decodes it Note This selection is unavailable when the Multiple Symbols Selection is turned on Multiple Symbols When this programming selection is turned On it allows you to read multiple symbols with a single pull of the imager s trigger If you press and hold the trig ger aiming the imager at a series of symbols it reads unique symbols once beeping if turned on for each read The imager attempts to find and decode new symbols as long as the trigger is pulled When this programming selection is turned Off the imager will only read the symbol closest to the aiming
32. 4 Supported Interface Keys ASCII HEX IBM Memorex Telex 102 Supported Keys Memorex Telex 88 Supported Keys NUL 00 Reserved Reserved SOH 01 Enter Enter STX 02 F11 PF10 ETX 03 F12 PF11 EOT 04 F13 PF12 ENQ 05 F14 Reserved ACK 06 F15 Reserved BEL 07 New Line New Line BS 08 F16 Field Forward HT 09 F17 Field Forward LF 0A F18 Reserved VT 0B Tab Field Forward Field Forward FF 0C Delete Delete CR 0D Field Exit New Line SO 0E Insert Insert SI 0F Clear Erase DLE 10 Error Reset Error Reset DC1 11 Home Reserved DC2 12 Print Print DC3 13 Back Space Back Space DC4 14 Back Tab Back Field NAK 15 F19 Reserved SYN 16 F1 PF1 ETB 17 F2 PF2 CAN 18 F3 PF3 EM 19 F4 PF4 SUB 1A F5 PF5 ESC 1B F6 PF6 FS 1C F7 PF7 GS 1D F8 PF8 RS 1E F9 PF9 US 1F F10 Home IBM 3196 97 3476 77 3191 92 3471 72 Memorex Telex all models with 102 key keyboards Memorex Telex with 88 key keyboards 8 5 Supported Interface Keys ASCII HEX Esprit 200 400 ANSI Supported Keys Esprit 200 400 ASCII Supported Keys Esprit 200 400 PC Supported Keys NUL 00 Reserved Reserved Reserved SOH 01 New Line New Line New Line STX 02 N A N A N A ETX 03 N A N A N A EOT 04 N A N A N A ENQ 05 N A N A N A ACK 06 N A N A N A BEL 07 New Line New Line New Line BS 08 N A N A N A HT 09 Tab Tab Tab LF 0A N A N A N A
33. 80 Minimum Default 4 Maximum Default 48 PosiCode lt Default All PosiCode Settings gt On Off Minimum Message Length Maximum Message Length 7 30 PosiCode A and B You have to have PosiCode A and B on to read any of the PosiCode symbolo gies PosiCode Message Length Scan the bar codes below to change the message length Refer to Message Length on page 7 2 for additional information Minimum and Maximum lengths 2 80 Minimum Default 4 Maximum Default 48 Trioptic Code Trioptic Code is used for labeling magnetic storage media Note If you are going to scan Code 32 Pharmaceutical codes Trioptic Code must be off On Off A and B On No Limited A and B and Limited A On Limited B Off A and B and Limited B On Limited A Off Minimum Message Length Maximum Message Length On Off 7 31 Codablock F lt Default All Codablock F Settings gt Codablock F Codablock F Message Length Scan the bar codes below to change the message length Refer to Message Length on page 7 2 for additional information Minimum and Maximum lengths 1 2048 Minimum Default 1 Maximum Default 2048 Code 16K lt Default All Code 16K Settings gt On Off Minimum Message Length Maximum Message Length 7 32 Code 16K Code 16K Message Length Scan the bar codes below to change the message length Refer to Message Length on page 7 2 for additional information Minimum a
34. 9 steps of 5 ms each for a range of 0 495 ms Add Suffix Clear One Suffix Clear All Suffixes Enable Disable 4 5 Intercharacter Delay An intercharacter delay of up to 495 milliseconds may be placed between the transmission of each character of scanned data Scan the Intercharacter Delay bar code below then scan the number of milliseconds and the Save bar code using the Programming Chart inside the back cover of this manual To remove this delay scan the Intercharacter Delay bar code then set the number of steps to 0 Scan the Save bar code using the Programming Chart inside the back cover of this manual Note Intercharacter delays are not supported in USB serial emulation User Specified Intercharacter Delay An intercharacter delay of up to 495 milliseconds may be placed after the trans mission of a particular character of scanned data Scan the Delay Length bar code below then scan the number of milliseconds and the Save bar code using the Programming Chart inside the back cover of this manual Next scan the Character to Trigger Delay bar code then the 2 digit hex value for the ASCII character that will trigger the delay ASCII Conversion Chart Code Page 1252 on page A 3 To remove this delay scan the Delay Length bar code and set the number of steps to 0 Scan the Save bar code using the Programming Chart inside the back cover of this manual 1 2 3 4 5 Intercharacter Delay Prefix Scanned Da
35. ACEMENT OF THE DEFECTIVE PRODUCT WITH NEW OR REFURBISHED PARTS IN NO EVENT SHALL HII BE LIABLE FOR INDIRECT INCIDENTAL OR CONSE QUENTIAL DAMAGES AND IN NO EVENT SHALL ANY LIABILITY OF HII ARISING IN CONNECTION WITH ANY PRODUCT SOLD HEREUNDER WHETHER SUCH LIABILITY ARISES FROM A CLAIM BASED ON CON TRACT WARRANTY TORT OR OTHERWISE EXCEED THE ACTUAL AMOUNT PAID TO HII FOR THE PRODUCT THESE LIMITATIONS ON LIA BILITY SHALL REMAIN IN FULL FORCE AND EFFECT EVEN WHEN HII MAY HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH INJURIES LOSSES OR DAMAGES SOME STATES PROVINCES OR COUNTRIES DO NOT ALLOW THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CONSE 14 4 QUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU All provisions of this Limited Warranty are separate and severable which means that if any provision is held invalid and unenforceable such determina tion shall not affect the validity of enforceability of the other provisions hereof Use of any peripherals not provided by the manufacturer may result in damage not covered by this warranty This includes but is not limited to cables power supplies cradles and docking stations HII extends these warranties only to the first end users of the products These warranties are non transferable The duration of the limited warranty for the 3800g 3800gHD and 3800gPDF is five 5 years A 1 A Appendix A Symbology Chart Symbology AIM ID Possible
36. After the one bar code has been read the imager reverts to the primary data format See page 5 5 If you are programming the primary format scan 0 using the Pro gramming Chart inside the back cover of this manual If you are pro gramming an alternate format scan 1 2 or 3 depending on the alternate format you are programming Step 3 Terminal Type Refer to the Supported Terminals Chart page 2 2 and locate the Ter minal ID number for your PC Scan three numeric bar codes on the 5 2 inside back cover to program the imager for your terminal ID you must enter 3 digits For example scan 0 0 3 for an AT wedge Note The wildcard for all terminal types is 099 Step 4 Code I D In Appendix A find the symbology to which you want to apply the data format Locate the Hex value for that symbology and scan the 2 digit hex value from the Programming Chart inside the back cover of this manual Step 5 Length Specify what length up to 9999 characters of data will be acceptable for this symbology Scan the four digit data length from the Program ming Chart inside the back cover of this manual Note 50 characters is entered as 0050 9999 is a universal number indicating all lengths Step 6 Editor Commands Refer to the Format Editor Commands Chart page 5 2 Scan the symbols that represent the command you want to enter 94 alphanu meric characters may be entered for each symbology data format Step 7 Scan Save from the Prog
37. C A Addenda Required Not Required UPAARQ0 7 18 Required UPAARQ1 7 18 UPC A Addenda Separator Off UPAADS0 7 18 On UPAADS1 7 18 UPC E Default All UPC E Settings UPEDFT 7 19 UPC E0 Off UPEEN00 7 19 On UPEEN01 7 19 UPC E1 Off UPEEN10 7 19 On UPEEN11 7 19 Selection Setting Indicates default Serial Command Indicates a numeric entry Page 11 15 UPC E Expand Off UPEEXP0 7 20 On UPEEXP1 7 20 UPC E Check Digit Off UPECKX0 7 20 On UPECKX1 7 20 UPC E Number Sys tem Off UPENSX0 7 21 On UPENSX1 7 21 UPC E 2 Digit Addenda Off UPEAD20 7 21 On UPEAD21 7 21 UPC E 5 Digit Addenda Off UPEAD50 7 21 On UPEAD51 7 21 UPC E Addenda Required Not Required UPEARQ0 7 20 Required UPEARQ1 7 20 UPC E Addenda Separator Off UPEADS0 7 20 On UPEADS1 7 20 EAN JAN 13 Default All EAN JAN 13 Settings E13DFT 7 22 EAN JAN 13 Off E13ENA0 7 22 On E13ENA1 7 22 EAN JAN 13 Check Digit Off E13CKX0 7 22 On E13CKX1 7 22 EAN JAN 13 2 Digit Addenda Off E13AD20 7 22 On E13AD21 7 22 EAN JAN 13 5 Digit Addenda Off E13AD50 7 22 On E13AD51 7 22 EAN JAN 13 Addenda Required Not Required E13ARQ0 7 22 Required E13ARQ1 7 22 EAN JAN 13 Addenda Separator Off E13ADS0 7 23 On E13ADS1 7 23 ISBN Translate Off E13ISB0 7 23 On E13ISB1 7 23 Selection Setting Indicates default S
38. E1 Addenda Required When Addenda Required is set to on the imager will only read UPC E bar codes that have addenda Default Not Required UPC E0 and UPC E1 Addenda Separator When this feature is on there is a space between the data from the bar code and the data from the addenda When turned off there is no space Default On UPC E0 Check Digit Check Digit specifies whether the check digit should be transmitted at the end of the scanned data or not Default On Off On Not Required Required Off On Off On 7 21 UPC E0 Number System The numeric system digit of a U P C symbol is normally transmitted at the beginning of the scanned data but the unit can be programmed so it will not transmit it Default On UPC E0 Addenda This selection adds 2 or 5 digits to the end of all scanned UPC E data Default Off for both 2 Digit and 5 Digit Addenda EAN JAN 13 lt Default All EAN JAN Settings gt Off On 5 Digit Addenda Off 5 Digit Addenda On 2 Digit Addenda Off 2 Digit Addenda On 7 22 EAN JAN 13 EAN JAN 13 Check Digit This selection allows you to specify whether the check digit should be transmit ted at the end of the scanned data or not Default On EAN JAN 13 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN JAN 13 data Default Off for both 2 Digit and 5 Digit Addenda EAN JAN 13 Addenda Required When Addenda Required i
39. Limited Settings RSLDFT 7 27 GS1 DataBar Limited Off RSLENA0 7 27 On RSLENA1 7 27 GS1 DataBar Expanded Default All GS1 DataBar Expanded Settings RSEDFT 7 28 GS1 DataBar Expanded Off RSEENA0 7 28 On RSEENA1 7 28 GS1 DataBar Expanded Msg Length Minimum 4 74 4 RSEMIN 7 28 Maximum 4 74 74 RSEMAX 7 28 China Post Code Default All China Post Code Settings CPCDFT 7 28 China Post Code Off CPCENA0 7 28 On CPCENA1 7 28 China Post Code Msg Length Minimum 2 80 4 CPCMIN 7 28 Maximum 2 80 80 CPCMAX 7 28 Korea Post Code Default All Korea Post Code Settings KPCDFT 7 29 Korea Post Code Off KPCENA0 7 29 On KPCENA1 7 29 Korea Post Code Msg Length Minimum 2 80 4 KPCMIN 7 29 Maximum 2 80 48 KPCMAX 7 29 PosiCode Default All PosiCode Set tings POSDFT 7 29 Selection Setting Indicates default Serial Command Indicates a numeric entry Page 11 18 PosiCode Off POSENA0 7 30 On POSENA1 7 30 A and B On POSLIM0 7 30 A and B and Limited A On POSLIM1 7 30 A and B and Limited B On POSLIM2 7 30 PosiCode Msg Length Minimum 2 80 4 POSMIN 7 30 Maximum 2 80 48 POSMAX 7 30 Trioptic Code Off TRIENA0 7 30 On TRIENA1 7 30 Codablock F Default All Codablock F Settings CBFDFT 7 31 Codablock F Off CBFENA0 7 31 On CBFENA1 7 31 Codablock F Msg Length
40. Minimum 1 2048 1 CBF MIN 7 31 Maximum 1 2048 2048 CBF MAX 7 31 Code 16K Default All Code 16K Set tings 16KDFT 7 31 Code 16K Off 16KENA0 7 32 On 16KENA1 7 32 Code 16K Minimum 0 160 1 16KMIN 7 32 Maximum 0 160 160 16KMAX 7 32 Code 49 Default All Code 49 Set tings C49DFT 7 32 Code 49 Off C49ENA0 7 33 On C49ENA1 7 33 Code 49 Minimum 1 81 1 C49MIN 7 33 Maximum 1 81 81 C49MAX 7 33 Selection Setting Indicates default Serial Command Indicates a numeric entry Page 11 19 PDF417 3800gHD 3800gPDF only Default All PDF417 Set tings PDFDFT 7 33 PDF417 On PDFENA1 7 33 Off PDFENA0 7 33 PDF417 Msg Length Minimum 1 2750 1 PDFMIN 7 34 Maximum 1 2750 2750 PDFMAX 7 34 MicroPDF417 3800gHD 3800gPDF only Default All Micro PDF417 Settings MPDDFT 7 34 MicroPDF417 On MPDENA1 7 34 Off MPDENA0 7 34 MicroPDF417 Msg Length Minimum 1 366 1 MPDMIN 7 34 Maximum 1 366 366 MPDMAX 7 34 GS1 Composite Codes On COMENA1 7 34 Off COMENA0 7 34 UPC EAN Version On COMUPC1 7 35 Off COMUPC0 7 35 GS1 Composite Codes Msg Length Minimum 1 2435 1 COMMIN 7 35 Maximum 1 2435 2435 COMMAX 7 35 GS1 Emulation GS1 Emulation EANEMU2 7 35 GS1 128 Emulation EANEMU1 7 35 GS1 Emulation Off EANEMU0 7 35 Label Code 3800gHD 3800gPDF o
41. NA0 7 8 On I25ENA1 7 8 Interleaved 2 of 5 Check Digit No Check Char I25CK20 7 9 Validate But Don t Transmit I25CK21 7 9 Validate and Transmit I25CK22 7 9 Interleaved 2 of 5 Mes sage Length Minimum 2 80 4 I25MIN 7 9 Maximum 2 80 80 I25MAX 7 9 Code 93 Default All Code 93 Settings C93DFT 7 10 Code 93 Off C93ENA0 7 10 On C93ENA1 7 10 Code 93 Message Length Minimum 0 80 0 C93MIN 7 10 Maximum 0 80 80 C93MAX 7 10 Straight 2 of 5 Indus trial Default All Straight 2 of 5 Settings R25DFT 7 11 Straight 2 of 5 Indus trial Off R25ENA0 7 11 On R25ENA1 7 11 Straight 2 of 5 Indus trial Message Length Minimum 1 48 4 R25MIN 7 11 Maximum 1 48 48 R25MAX 7 11 Straight 2 of 5 IATA Default All Straight 2 of 5 IATA Settings A25DFT 7 11 Selection Setting Indicates default Serial Command Indicates a numeric entry Page 11 13 Straight 2 of 5 IATA Off A25ENA0 7 11 On A25ENA1 7 11 Straight 2 of 5 IATA Message Length Minimum 1 48 4 A25MIN 7 12 Maximum 1 48 48 A25MAX 7 12 Matrix 2 of 5 Default All Matrix 2 of 5 Settings X25DFT 7 12 Matrix 2 of 5 Off X25ENA0 7 12 On X25ENA1 7 12 Matrix 2 of 5 Message Length Minimum 1 80 4 X25MIN 7 12 Maximum 1 80 80 X25MAX 7 12 Code 11 Default All Code 11 Settings C11DFT 7 13 Code 11 Off C11ENA0 7
42. Note If you download new software into a unit the user programmed parameters are retained If you need to discard user programmed settings scan the Standard Product Default Settings bar code see Standard Product Default Settings on page 9 1 Visual Xpress 10 1 10 Visual Xpress Visual Xpress Introduction Visual Xpress provides a wide range of PC based programming functions that can be performed on an imager connected to your PC s COM port Visual Xpress allows you to download upgrades to the imager s firmware change pro grammed parameters and create and print programming bar codes Using Visual Xpress you can even save open the programming parameters for an imager This saved file can be e mailed or if required you can create a single bar code that contains all the customized programming parameters and mail or fax that bar code to any location Users in other locations can scan the bar code to load in the customized programming To communicate with an imager Visual Xpress requires that the PC have at least one available serial communication port or a serial port emulation using a physical USB port If you are using the serial port and RS 232 cable an exter nal power supply is required When using a USB serial port emulation only a USB cable is required Visual Xpress Operations The Visual Xpress software performs the following operations Scan Data Scan Data allows you to scan bar codes and display the bar code
43. SBT ratified a standard for communicating critical blood information in a uniform manner The use of ISBT formats requires a paid license The ISBT 128 Application Specification describes 1 the critical data elements for labeling blood products 2 the current recommendation to use Code 128 due to its high degree of security and its space efficient design 3 a variation of Code 128 that supports concatenation of neighboring symbols and 4 the standard layout for bar codes on a blood product label Use the bar codes below to turn concatenation on or off Default Off Minimum Message Length Maximum Message Length On Off Off On 7 15 Code 128 Message Length Scan the bar codes below to change the message length Refer to Message Length on page 7 2 for additional information Minimum and Maximum lengths 0 80 Minimum Default 0 Maximum Default 80 Code 128 Code Page Code pages define the mapping of character codes to characters If the data received does not display with the proper characters it may be because the bar code being scanned was created using a code page that is different from the one the host program is expecting If this is the case scan the bar code below select the code page with which the bar codes were created from the chart Code Page Mapping of Printed Bar Codes on page A 5 and scan the value and the Save bar code from the Programming Chart inside the back cover of this manual The data charact
44. Short Delay 500 ms DLYGRD50 0 3 3 Medium Delay 1000 ms DLYGRD10 00 3 3 Long Delay 1500 ms DLYGRD15 00 3 3 User Specified Good Read Delay Range 0 30 000 ms DLYGRD 3 3 Trigger Mode Manual Serial Trigger TRGMOD0 3 3 Read Time Out 0 300 000 ms 30 000 TRG STO 3 4 Automatic Trigger TRGMOD1 3 4 Presentation Mode TRGMOD3 3 4 Continuous Illumination On ILLAON1 3 4 Continuous Illumination Off ILLAON0 3 4 Hands Free Time Out 0 300 000 seconds 5000 TRGPTO 3 5 Selection Setting Indicates default Serial Command Indicates a numeric entry Page 11 9 Reread Delay Short 500 ms DLYRRD50 0 3 5 Medium 750 ms DLYRRD75 0 3 5 Long 1000 ms DLYRRD10 00 3 5 Extra Long 2000 ms DLYRRD30 00 3 5 User Specified Reread Delay Range 0 30 000 ms DLYRRD 3 5 Centering Centering On DECWIN1 3 6 Centering Off DECWIN0 3 6 Left of Centering Win dow 40 DECLFT 3 6 Right of Centering Win dow 60 DECRGT 3 6 Output Sequence Edi tor Enter Sequence SEQBLK 3 9 Default Sequence SEQDFT 3 9 Require Output Sequence Required SEQ_EN2 3 9 On Not Required SEQ_EN1 3 9 Off SEQ_EN0 3 9 Multiple Symbols On SHOTGN1 3 13 Off SHOTGN0 3 13 No Read On SHWNRD1 3 12 Off SHWNRD0 3 12 Video Reverse On VIDREV1 3 12 Off VIDREV0 3 12 Prefix Suffix Sele
45. Stop Bits and Parity 2 8 RS 232 Handshaking 2 10 Chapter 3 Output Table of Contents ii Good Read Indicators 3 1 Beeper Good Read 3 1 Beeper Volume Good Read 3 1 Beeper Pitch Good Read 3 1 Beeper Duration Good Read 3 2 LED Good Read 3 2 Number of Beeps Good Read 3 2 Good Read Delay 3 3 User Specified Good Read Delay 3 3 Trigger Modes 3 3 Manual Serial Trigger 3 3 Automatic Trigger 3 4 Presentation Mode 3 4 Continuous Illumination Mode 3 4 Hands Free Time Out 3 4 Reread Delay 3 5 User Specified Reread Delay 3 5 Centering Window 3 5 Output Sequence Overvi
46. Transmit Minimum Message Length Maximum Message Length 7 10 Code 93 lt Default All Code 93 Settings gt Code 93 Code 93 Message Length Scan the bar codes below to change the message length Refer to Message Length on page 7 2 for additional information Minimum and Maximum lengths 0 80 Minimum Default 0 Maximum Default 80 Code 93 Code Page Code pages define the mapping of character codes to characters If the data received does not display with the proper characters it may be because the bar code being scanned was created using a code page that is different from the one the host program is expecting If this is the case scan the bar code below select the code page with which the bar codes were created from the chart Code Page Mapping of Printed Bar Codes on page A 5 and scan the value and the Save bar code from the Programming Chart inside the back cover of this manual The data characters should then appear properly On Off Minimum Message Length Maximum Message Length Code 93 Code Page 7 11 Straight 2 of 5 Industrial three bar start stop lt Default All Straight 2 of 5 Settings gt Straight 2 of 5 Industrial Straight 2 of 5 Industrial Message Length Scan the bar codes below to change the message length Refer to Message Length on page 7 2 for additional information Minimum and Maximum lengths 1 48 Minimum Default 4 Maximum Default 48 Straight 2 of 5 IATA two bar star
47. a good read The beeps and LED flashes are in sync with one another To change the number of beeps scan the bar code below and then scan a digit 1 9 bar code and the Save bar code on the Programming Chart inside the back cover of this manual Default One Normal Beep Short Beep On Off Number of Pulses 3 3 Good Read Delay This sets the minimum amount of time before the imager can read another bar code Default No Delay User Specified Good Read Delay If you want to set your own length for the good read delay scan the bar code below then set the delay from 0 30 000 milliseconds by scanning digits from the inside back cover then scanning Save Trigger Modes Manual Serial Trigger You can activate the imager either by pressing the trigger or using a serial trig ger command see Trigger Commands on page 11 4 When in manual trigger mode the imager scans until a bar code is read or until the trigger is released When in serial mode the imager scans until a bar code has been read or until the deactivate command is sent In serial mode the imager can also be set to turn itself off after a specified time has elapsed see Read Time Out which fol lows Read Time Out Use this selection to set a time out in milliseconds of the imager s trigger when using serial commands to trigger the imager Once the imager has timed out you can activate the imager either by pressing the trigger or using a seria
48. age A 3 FC Disables suppress filter and clear all suppressed characters Syntax FC E4 Replaces up to 15 characters in the data string with user specified charac ters Replacement continues until the E5 command is encountered Syn tax E4nnxx1xx2yy1yy2 zz1zz2 where nn is the total count of both characters to be replaced plus replacement characters xx1 defines charac ters to be replaced and xx2 defines replacement characters continuing through zz1 and zz2 E5 Terminates character replacement Syntax E5 FE Compare character in current cursor position to the character xx If char acters are equal increment cursor If characters are not equal no format match Syntax FExx xx stands for the hex value for an ASCII code see ASCII Conversion Chart Code Page 1252 on page A 3 EC Check to make sure there is an ASCII number at the current cursor posi tion If character is not numeric format is aborted Syntax EC ED Check to make sure there is a non numeric ASCII character at the current cursor position If character is numeric format is aborted Syntax ED Data Format Editor Enter Data Format Default Data Format Clear One Data Format Save Discard Clear All Data Formats 5 5 Data Formatter When Data Formatter is turned off the bar code data is output to the host as read including prefixes and suffixes Choose one of the following options Default Data Formatter On When Data Formatter is requ
49. ard Product Default Settings 11 5 Menu Commands Selection Setting Indicates default Serial Command Indicates a numeric entry Page Factory Default Set tings Default DEFALT Terminal Interfaces Terminal ID USB PC Keyboard TERMID 2 1 Program Keyboard Country USA KBDCTY0 2 4 Belgium KBDCTY1 2 4 Denmark KBDCTY8 2 4 Finland KBDCTY2 2 4 France KBDCTY3 2 4 Germany Austria KBDCTY4 2 4 Great Britain KBDCTY7 2 4 Italy KBDCTY5 2 4 Norway KBDCTY9 2 4 Spain KBDCTY10 2 4 Switzerland KBDCTY6 2 4 Keyboard Style Regular KBDSTY0 2 5 Caps Lock KBDSTY1 2 5 Shift Lock KBDSTY2 2 5 Automatic Caps Lock KBDSTY6 2 5 Emulate External Keyboard KBDSTY5 2 6 11 6 Keyboard Modifiers Windows Mode Control ASCII KBDCAS2 2 6 Control ASCII Off KBDCAS0 2 6 DOS Mode Control ASCII Mode On KBDCAS1 2 6 Turbo Mode Off KBDTMD0 2 6 Turbo Mode On KBDTMD1 2 6 Numeric Keypad Off KBDNPS0 2 7 Numeric Keypad On KBDNPS1 2 7 Auto Direct Conn Off KBDADC0 2 7 Auto Direct Conn On KBDADC1 2 7 Serial Port Connection RS 232 PAP232 1 7 Baud Rate 300 BPS 232BAD0 2 8 600 BPS 232BAD1 2 8 1200 BPS 232BAD2 2 8 2400 BPS 232BAD3 2 8 4800 BPS 232BAD4 2 8 9600 BPS 232BAD5 2 8 19200 BPS 232BAD6 2 8 38400 BPS 232BAD7 2 8 57600 BPS 232BAD8 2 8 115200 BPS 232BAD9 2 8 Selection Setting Indicate
50. ass A EMC requirements Mexico Applicable if NOM logo is marked on product Conforms to NOM 019 M IC International Eye Safety Statement LED This device has been tested in accordance with IEC60825 1 1993 A 1997 A2 2001 LED safety and has been certified to be under the limits of a Class 1 LED device Caution Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure CB Scheme Certified to IEC60950 1 I T E Product Safety Solids and Water Protection The devices have a rating of IP41 immunity of foreign particles and dripping water tested to Standard EN60259 Patents Please refer to the product packaging for a list of patents 3800g Imager Identification Light Source Item Number Serial Number and Revision Compliance Label location 1 1 1 Getting Started About This Manual This User s Guide provides installation and programming instructions for the 3800g Product specifications dimensions warranty and customer support information are also included Honeywell bar code imagers are factory programmed for the most common ter minal and communications settings If you need to change these settings pro gramming is accomplished by scanning the bar codes in this guide An asterisk next to an option indicates the default setting Unpacking the Imager After you open the shipping carton containing the
51. ctions Add CR Suffix to All Symbologies VSUFCR 4 3 Prefix Add Prefix PREBK2 4 3 Clear One Prefix PRECL2 4 3 Clear All Prefixes PRECA2 4 3 Selection Setting Indicates default Serial Command Indicates a numeric entry Page 11 10 Suffix Add Suffix SUFBK2 4 4 Clear One Suffix SUFCL2 4 4 Clear All Suffixes SUFCA2 4 4 Function Code Trans mit Enable RMVFNC0 4 4 Disable RMVFNC1 4 4 Intercharacter Delay DLYCHR 4 5 User Specified Inter character Delay Delay Length DLYCRX 4 5 Character to Trigger Delay DLY_XX 4 5 Interfunction Delay DLYFNC 4 6 Intermessage Delay DLYMSG 4 6 Data Formatter Selections Data Format Editor Default Data Format None DFMDF3 5 4 Enter Data Format DFMBK3 5 4 Clear One Data Format DFMCL3 5 4 Clear All Data Formats DFMCA3 5 4 Data Formatter Off DFM_EN0 5 5 On but Not Required DFM_EN1 5 5 On Required DFM_EN2 5 5 Alternate Data For mats 1 VSAF_1 5 5 2 VSAF_2 5 5 3 VSAF_3 5 5 Secondary Interface Selections Enabling the Second ary Interface Disable 2IF_EN0 6 1 Enable 2IF_EN1 6 1 Secondary RS 232 Connection RS 232 Interface 2IFTYP0 6 2 Secondary Trigger Mode Manual Trigger 2IFTRG0 6 2 Automatic Trigger 2IFTRG1 6 2 Presentation Mode 2IFTRG3 6 2 Selection Setting Indicates default Serial Command Indicates a numeric entry Page 11
52. data in a win dow Scan Data lets you send serial commands to the imager and receive imager response that can be seen in the Scan Data window The data dis played in the Scan Data window can either be saved in a file or printed Configure Configure displays the programming and configuration data of the imager The imager s programming and configuration data is grouped into different catego ries Each category is displayed as a tree item under the Configure tree node in the application explorer When one of these tree nodes is clicked the right hand side is loaded with the parameters form belonging to that particular cate gory The Configure tree option has all the programming and configuration parameters specified for an imager You can set or modify these parameters as required You can later write the modified settings to the imager or save them to a dcf file Imaging Imaging provides all the image related functions that a 2D Imager can perform You can capture an image using the current settings and the image will be dis played in an image window Images captured from the imager can be saved to files in different image formats You can modify the image settings and save the image settings to an INI file which can be loaded later to capture new images Imaging also lets you preview the images continuously captured by the imager 10 2 Installing Visual Xpress from the Web 1 Access the Honeywell web site at www honeywell co
53. dinavia 8 lt 9 6 France 8 6 Germany 6 Italy 6 Switzerland lt 6 United Kingdom 6 Denmark 8 9 6 Norway 8 9 6 Spain 6 8 3 Supported Interface Keys ASCII HEX IBM AT XT and PS 2 Compatibles WYSE PC AT Supported Keys IBM XTs and Compatibles Supported Keys IBM DDC Memorex Telex Harris Supported Keys NUL 00 Reserved Reserved Reserved SOH 01 Enter KP CR Enter Enter STX 02 Cap Lock Caps Lock F11 ETX 03 ALT make Reserved F12 EOT 04 ALT break Reserved F13 ENQ 05 CTRL make Reserved F14 ACK 06 CTRL break Reserved F15 BEL 07 CR Enter CR Enter New Line BS 08 Reserved Reserved F16 HT 09 Tab Tab F17 LF 0A Reserved Reserved F18 VT 0B Tab Tab Tab Field Forward FF 0C Delete Delete Delete CR 0D CR Enter CR Enter Field Exit New Line SO 0E Insert Insert Insert SI 0F Escape Escape F19 DLE 10 F11 Reserved Error Reset DC1 11 Home Home Home DC2 12 Print Print F20 DC3 13 Back Space Back Space Back Space DC4 14 Back Tab Back Tab Backfield Back Tab NAK 15 F12 Reserved F21 SYN 16 F1 F1 F1 ETB 17 F2 F2 F2 CAN 18 F3 F3 F3 EM 19 F4 F4 F4 SUB 1A F5 F5 F5 ESC 1B F6 F6 F6 FS 1C F7 F7 F7 GS 1D F8 F8 F8 RS 1E F9 F9 F9 US 1F F10 F10 F10 IBM 3191 92 3471 72 3196 97 3476 77 Telex all models 8
54. e scan the Enable bar code Default Disable Secondary RS 232 Connection All communication parameters between the imager and terminal must match for correct data transfer through the serial port using RS 232 protocol Models Primary Interfaces Secondary Interfaces 3800G04E 3800G14E TTL level RS 232 USB Key board wedge TTL level RS 232 3800G05E 3800G15E TTL level RS 232 IBM Retail USB Retail USB Keyboard wedge TTL level RS 232 3800GHD24E TTL level RS 232 USB Key board wedge TTL level RS 232 3800GPDF04E TTL level RS 232 USB Key board wedge TTL level RS 232 Disable Enable 6 2 RS 232 programmable selections are used by both the primary and secondary interfaces Changing an RS 232 parameter e g baud rate or parity while in primary or secondary mode will affect both interfaces If you want to change the RS 232 settings refer to the Connecting the Imager with RS 232 Serial Port section on page 1 6 Secondary Trigger Mode Manual Trigger You must press the imager trigger to scan When not scan ning idle power is maintained Default Manual Trigger Automatic Trigger The imager scans continuously at full power Presentation Mode The LEDs are off until a bar code is presented to the imager Then the LEDs turn on automatically to read the code Presentation Mode uses ambient light to detect the bar codes Hands Free Time Out The Automatic Trigger and Presentation Modes are ref
55. e Enter Return key or the Tab key for example You need to program a suffix Programming a suffix enables the scanner to out put the bar code data plus the key you need such as CR to enter the data into your application Refer to Prefix Suffix Overview on page 4 1 for further information Does the scanner read the bar code incorrectly If the scanner reads a bar code but the data is not displayed correctly on the host screen The scanner may not be programmed for the appropriate terminal interface For example you scan 12345 and the host displays es Reprogram the scanner with the correct Plug and Play or Terminal selection bar code See Chapter 1 and Chapter 2 The scanner may not be programmed to output your bar code data properly For example you scan 12345 and the host displays A12345B Reprogram the scanner with the proper symbology selections See Chapter 7 The scanner won t read your bar code at all 1 Scan the sample bar codes in the back of this manual If the scanner reads the sample bar codes check that your bar code is readable Verify that your bar code symbology is enabled see Chapter 7 2 If the scanner still can t read the sample bar codes scan All Symbologies on page 7 2 If you aren t sure what programming options have been set in the scanner or if you want the factory default settings restored scan Resetting the Standard Product Defaults on page 11 4
56. e because the bar code being scanned was created using a code page that is different from the one the host program is expecting If this is the case scan the bar code below select the code page with which the bar codes were created from the chart Code Page Mapping of Printed Bar Codes on page A 5 and scan the value and the Save bar code from the Programming Chart inside the back cover of this manual The data characters should then appear properly Interleaved 2 of 5 lt Default All Interleaved 2 of 5 Settings gt Interleaved 2 of 5 Check Digit No Check Digit indicates that the imager reads and transmits bar code data with or without a check digit When Check Digit is set to Validate but Don t Transmit the unit only reads Interleaved 2 of 5 bar codes printed with a check digit but will not transmit the check digit with the scanned data Full ASCII Off Full ASCII On Code 39 Code Page On Off 7 9 When Check Digit is set to Validate and Transmit the imager only reads Inter leaved 2 of 5 bar codes printed with a check digit and will transmit this digit at the end of the scanned data Default No Check Digit Interleaved 2 of 5 Message Length Scan the bar codes below to change the message length Refer to Message Length on page 7 2 for additional information Minimum and Maximum lengths 2 80 Minimum Default 4 Maximum Default 80 Validate but Don t Transmit No Check Digit Validate and
57. e device s Codabar Coding Enable CBRENA is set to 1 or on the Start Stop Character SSX is set to 0 or Don t Transmit the Check Character CK2 is set to 0 or Not Required concatenation CCT is set to 1 or Enabled the Minimum Message Length MIN is set to 2 characters the Maximum Message Length MAX is set to 60 characters and the Default setting DFT has no value 11 4 Trigger Commands You can activate and deactivate the imager with serial trigger commands First the imager must be put in Manual Serial Trigger Mode either by scanning the Manual Serial Trigger Mode bar code page 3 3 or by sending the Manual Serial Menu Command page 11 8 Once the imager is in serial trigger mode the trigger is activated and deactivated by sending the following commands Activate SYN T CR Deactivate SYN U CR The imager scans until a bar code has been read until the deactivate command is sent or until the serial time out has been reached see Read Time Out on page 3 3 for a description and the serial command on page 11 8 Resetting the Standard Product Defaults If you aren t sure what programming options are in your imager or you ve changed some options and want the factory settings restored scan the Stan dard Product Default Settings bar code below The chart on the following pages lists the factory default settings for each of the menu commands indicated by an asterisk on the programming pages Stand
58. eck Character is set to Validate and Transmit the imager only reads Code 39 bar codes printed with a check character and will transmit this charac ter at the end of the scanned data Default No Check Character Code 39 Message Length Scan the bar codes below to change the message length Refer to Message Length on page 7 2 for additional information Minimum and Maximum lengths 0 48 Minimum Default 0 Maximum Default 48 Code 39 Append This function allows the imager to append the data from several Code 39 bar codes together before transmitting them to the host computer When this func tion is enabled the imager stores those Code 39 bar codes that start with a space excluding the start and stop symbols and does not immediately trans mit the data The imager stores the data in the order in which the bar codes are read deleting the first space from each The imager transmits the appended data when it reads a Code 39 bar code that starts with a character other than a space Default Off Validate but Don t Transmit No Check Character Validate and Transmit Minimum Message Length Maximum Message Length Off On 7 7 Code 32 Pharmaceutical PARAF Code 32 Pharmaceutical is a form of the Code 39 symbology used by Italian pharmacies This symbology is also known as PARAF Default Off Note Trioptic Code must be turned off to scan Code 32 Pharmaceutical codes Full ASCII If Full ASCII Code 39 dec
59. ed 7 20 UPC E0 and UPC E1 Addenda Separator 7 20 UPC E0 Check Digit 7 20 UPC E0 Number System 7 21 UPC E0 Addenda 7 21 EAN JAN 13 7 21 EAN JAN 13 Check Digit 7 22 EAN JAN 13 Addenda 7 22 EAN JAN 13 Addenda Required 7 22 EAN JAN 13 Addenda Separator 7 23 ISBN Translate 7 23 EAN JAN 8 7 23 EAN JAN 8 Check Digit 7 24 EAN JAN 8 Addenda 7 24 EAN JAN 8 Addenda Required 7 24 EAN JAN 8 Addenda Separator 7 25 MSI 7 25 MSI Check Character 7 25 MSI Message Length 7 26 Plessey Code 7 26 Plessey Message Length 7 26 GS1 DataBar Omnidirectional 7 26 GS1 DataBar Limited
60. een Menu Command Syntax Menu commands have the following syntax spaces have been used for clarity only Prefix Tag SubTag Data SubTag Data Tag SubTag Data Storage Prefix Three ASCII characters SYN M CR ASCII 22 77 13 Tag A 3 character case insensitive field that identifies the desired menu command group For example all RS 232 configuration settings are identified with a Tag of 232 SubTag A 3 character case insensitive field that identifies the desired menu command within the tag group For example the SubTag for the RS 232 baud rate is BAD Data The new value for a menu setting identified by the Tag and Sub Tag Storage A single character that specifies the storage table to which the command is applied An exclamation point performs the com mand s operation on the device s volatile menu configuration table A period performs the command s operation on the device s non volatile menu configuration table Use the non volatile table only for semi permanent changes you want saved through a power cycle 11 2 Query Commands Several special characters can be used to query the device about its settings What is the default value for the setting s What is the device s current value for the setting s What is the range of possible values for the setting s The de vice s response uses a dash to indicate a continuous range of values A pipe separates items
61. er to output data when scanning more than one symbol in whatever order your application requires regardless of the order in which the bar codes are scanned Reading the Default Sequence symbol programs the imager to the Universal values shown below These are the defaults Be certain you want to delete or clear all formats before you read the Default Sequence symbol Note To make Output Sequence Editor selections you ll need to know the code I D code length and character match es your application requires Use the Alphanumeric symbols inside back cover to read these options Note You must hold the trigger while reading each bar code in a sequence To Add an Output Sequence 1 Scan the Enter Sequence symbol see Require Output Sequence page 3 9 2 Code I D On the Symbology Chart on page A 1 find the symbology to which you want to apply the output sequence format Locate the Hex value for that symbol ogy and scan the 2 digit hex value from the Programming Chart inside back cover 3 Length Specify what length up to 9999 characters of data output will be acceptable for this symbology Scan the four digit data length from the Programming Chart Note 50 characters is entered as 0050 9999 is a universal num ber indicating all lengths When calculating the length you must count any programmed prefixes suffixes or formatted characters as part of the length unless using 9999 4 Character Match Sequences On
62. erial Command Indicates a numeric entry Page 11 16 EAN JAN 8 Default All EAN JAN 8 Settings EA8DFT 7 24 EAN JAN 8 Off EA8ENA0 7 24 On EA8ENA1 7 24 EAN JAN 8 Check Digit Off EA8CKX0 7 24 On EA8CKX1 7 24 EAN JAN 8 2 Digit Addenda Off EA8AD20 7 24 On EA8AD21 7 24 EAN JAN 8 5 Digit Addenda Off EA8AD50 7 24 On EA8AD51 7 24 EAN JAN 8 Addenda Required Not Required EA8ARQ0 7 24 Required EA8ARQ1 7 24 EAN JAN 8 Addenda Separator Off EA8ADS0 7 25 On EA8ADS1 7 25 Coupon Code Off CPNENA0 7 25 On CPNENA1 7 19 MSI Default All MSI Settings MSIDFT 7 25 MSI Off MSIENA0 7 25 On MSIENA1 7 25 MSI Check Character Validate Type 10 but Don t Transmit MSICHK0 7 25 Validate Type 10 and Transmit MSICHK1 7 25 MSI Message Length Minimum 4 48 4 MSIMIN 7 26 Maximum 4 48 48 MSIMAX 7 26 Plessey Code Default All Plessey Set tings PLSDFT 7 26 Plessey Code Off PLSENA0 7 26 On PLSENA1 7 26 Plessey Message Length Minimum 4 48 4 PLSMIN 7 26 Maximum 4 48 48 PLSMAX 7 26 Selection Setting Indicates default Serial Command Indicates a numeric entry Page 11 17 GS1 DataBar Omnidi rectional Default All GS1 DataBar Omnidirec tional Settings RSSDFT 7 27 GS1 DataBar Omnidi rectional Off RSSENA0 7 27 On RSSENA1 7 27 GS1 DataBar Limited Default All GS1 DataBar
63. erred to as hands free modes If the imager s trigger is pulled when using a hands free mode the imager changes to manual trigger mode You can set the time the imager should remain in manual trigger mode by setting the Hands Free Time Out Once the time out value is reached if there have been no further trigger pulls the imager reverts to the original hands free mode Note If you change the time out duration for the secondary interface the duration of the primary interface will also be changed RS 232 Interface Manual Trigger Automatic Trigger Presentation Mode 6 3 Scan the Hands Free Time Out bar code then scan the time out duration from 0 300 000 milliseconds from the inside back cover and Save Default 5 000 ms Hands Free Time Out 6 4 7 1 7 Symbologies Introduction This programming section contains the following menu selections Refer to Chapter 11 for settings and defaults All Symbologies Korea Post Code China Post Code Label Code 3800gHD 3800gPDF only Codabar Matrix 2 of 5 Codablock F MicroPDF417 3800gHD 3800gPDF only Code 11 MSI Code 16K PDF417 3800gHD 3800gPDF only Code 39 Plessey Code Code 32 Pharmaceutical PARAF PosiCode Code 49 Straight 2 of 5 IATA two bar start stop Code 93 Straight 2 of 5 Industrial three bar start sto
64. ers should then appear properly Code 128 Function Code Transmit By default Code 128 function codes are not transmitted with Code 128 bar code data However if you wish to transmit Code 128 function codes with the bar code data scan the Function Codes On bar code below Default Off Telepen lt Default All Telepen Settings gt Minimum Message Length Maximum Message Length Code 128 Code Page Function Codes Off Function Codes On 7 16 Telepen Telepen Output Using AIM Telepen Output the imager reads symbols with start stop pattern 1 and decodes them as standard full ASCII start stop pattern 1 When Original Telepen Output is selected the imager reads symbols with start stop pattern 1 and decodes them as compressed numeric with optional full ASCII start stop pattern 2 Default AIM Telepen Output Telepen Message Length Scan the bar codes below to change the message length Refer to Message Length on page 7 2 for additional information Minimum and Maximum lengths 1 60 Minimum Default 1 Maximum Default 60 On Off Original Telepen Output AIM Telepen Output Minimum Message Length Maximum Message Length 7 17 UPC A lt Default All UPC A Settings gt UPC A UPC A Check Digit This selection allows you to specify whether the check digit should be transmit ted at the end of the scanned data or not Default On UPC A Number System The numeric system digit of a U P C
65. essage Length Minimum Message Length On Off 7 35 UPC EAN Version Scan the UPC EAN Version On barcode to decode GS1 Composite symbols that have a UPC or EAN linear component This does not affect GS1 Compos ite symbols with a GS1 128 or GS1linear component If either of these codes are the linear component either Code 128 or the correct GS1 code must be enabled Default Off GS1 Composite Code Message Length Scan the barcodes below to change the message length Refer to Message Length page 7 2 for additional information Minimum and Maximum lengths 1 2435 Minimum Default 1 Maximum Default 2435 GS1 Emulation The imager can automatically format the output from any GS1 data carrier to emulate what would be encoded in an equivalent GS1 128 or GS1 DataBar symbol GS1 data carriers include UPC A and UPC E EAN 13 and EAN 8 ITF 14 GS1 128 and GS1 128 DataBar and GS1Composites If GS1 128 Emulation is selected the AIM Symbology Identifier will be reported as C1 If GS1 DataBar Emulation is selected the AIM Symbology Identifier will be reported as e0 Any application that accepts GS1 data can be simplified since it only needs to recognize one data carrier type Default GS1 Emulation Off UPC EAN Version On UPC EAN Version Off Maximum Message Length Minimum Message Length GS1 Data Bar Emulation GS1 128 Emulation GS1 Emulation Off 7 36 Label Code 3800gHD 3800gPDF only
66. ew 3 8 Output Sequence Editor 3 9 Require Output Sequence 3 9 Output Sequence Editor 3 11 Require Output Sequence 3 11 Multiple Symbols 3 12 No Read 3 12 Video Reverse 3 13 Chapter 4 Data Editing Prefix Suffix Overview 4 1 To Add a Prefix or Suffix 4 1 To Clear One or All Prefixes or Suffixes 4 2 To Add a Carriage Return Suffix to All Symbologies 4 3 Prefix Selections 4 3 Suffix Selections 4 4 Function Code Transmit 4 4 iii Intercharacter Interfunction and Intermessage Delays 4 4 Intercharacter Delay 4 5 User Specified Intercharacter Delay 4 5 Interfunction Delay 4 6 Intermessage Delay
67. f a bar code must be within the window to be decoded or out put by the imager Hands Free Time Out Short 500 ms Medium 750 ms Long 1000 ms Extra Long 2000 ms User Specified Reread Delay 3 6 To change the left or right edge of the centering window scan Centering On then scan one of the following bar codes Then scan the percent you want to shift the centering window using digits on the inside back cover of this manual Scan Save Default Centering 40 for Left 60 for Right The figure below illustrates the percentage range from 1 to 100 Left of Centering Window Right of Centering Window Centering Off Centering On 20 30 90 80 40 60 70 10 0 100 3 7 Example If you have two bar codes next to one another and the centering window is set to 40 left edge and 60 right edge only the bar code that intersects that window will be decoded 20 30 90 80 40 60 70 10 0 100 Decoded bar code 3 8 Output Sequence Overview Require Output Sequence When turned off the bar code data will be output to the host as the imager decodes it When turned on all output data must conform to an edited sequence or the imager will not transmit the output data to the host device Note This selection is unavailable when the Multiple Symbols Selection is turned on Output Sequence Editor This programming selection allows you to program the imag
68. fault 4 Maximum Default 48 GS1 DataBar Omnidirectional lt Default All GS1 DataBar Omnidirectional Settings gt Minimum Message Length Maximum Message Length On Off Minimum Message Length Maximum Message Length 7 27 GS1 DataBar Omnidirectional GS1 DataBar Limited lt Default All GS1 DataBar Limited Settings gt GS1 DataBar Limited GS1 DataBar Expanded lt Default All GS1 DataBar Expanded Settings gt On Off On Off 7 28 GS1 DataBar Expanded GS1 DataBar Expanded Message Length Scan the bar codes below to change the message length Refer to Message Length on page 7 2 for additional information Minimum and Maximum lengths 4 74 Minimum Default 4 Maximum Default 74 China Post Code lt Default All China Post Code Settings gt China Post Code China Post Message Length Scan the bar codes below to change the message length Refer to Message Length on page 7 2 for additional information Minimum and Maximum lengths 2 80 Minimum Default 4 Maximum Default 80 On Off Minimum Message Length Maximum Message Length On Off Minimum Message Length Maximum Message Length 7 29 Korea Post Code lt Default All Korea Post Code Settings gt Korea Post Code Korea Post Message Length Scan the bar codes below to change the message length Refer to Message Length on page 7 2 for additional information Minimum and Maximum lengths 2
69. h LPS output rated 5Vdc 2 4A Contact your sales representative to order Honeywell part number PS5U 4xE 12 2 3800gHD 3800gPDF Product Specifications Parameter Specification Dimensions Typical Height 5 9 inches 15 cm Length 4 4 inches 11 2 cm Width 3 1 inches 7 9 cm Weight 5 6 ounces 160 g Light Source 628 nm visible red LED 300 W max radiant power Scan Rate 270 scans per second in most usages Skew Angle 65 degrees Pitch Angle 65 degrees Horizontal Velocity 10 inches 50 cm per second Scan Contrast 37 minimum Voltage Requirements 4 5 to 5 5 VDC at imager Current Draw Max Scanning Standby Inrush 3800gHDX4E 3800gPDFX4E 5VDC 450mA 87mA 450mA Temperature Ranges Operating 32 F to 122 F 0 C to 50 C Storage 40 F to 140 F 40 C to 60 C Humidity 0 to 95 non condensing Mechanical Drop Operational after 50 drops from 5 feet 1 5 m to concrete Vibration Withstands 5G peak from 22 to 300 Hz ESD Sensitivity 15 kV to any external surface Sealant Rating IP41 Power Sources Requirements Host powered options available e g USB 12VDC adapter Use only a UL cUL listed power supply with LPS output rated 5Vdc 2 4A Contact your sales representative to order Honeywell part number PS5U 4xE 12 3 Standard Cable Pinouts Keyboard Wedge 10 Pin RJ41 Modular Plug connects to the imager handle 1 2 Cord shield
70. ic characters as if entered from a numeric keypad Default Off Automatic Direct Connect Mode This selection can be used if you have an IBM AT style terminal and the system is dropping characters Default Off Numeric Keypad Mode On Numeric Keypad Mode Off Automatic Direct Connect Mode On Automatic Direct Connect Mode Off 2 8 RS 232 Baud Rate Baud Rate sends the data from the imager to the terminal at the specified rate The host terminal must be set for the same baud rate as the imager Default 38 400 RS 232 Word Length Data Bits Stop Bits and Parity Data Bits sets the word length at 7 or 8 bits of data per character If an applica tion requires only ASCII Hex characters 0 through 7F decimal text digits and punctuation select 7 data bits For applications which require use of the full ASCII set select 8 data bits per character Default 8 Stop Bits sets the stop bits at 1 or 2 Default 1 300 2400 600 1200 4800 38400 9600 19200 115 200 57 600 2 9 Parity provides a means of checking character bit patterns for validity Default None 7 Data 1 Stop Parity Even 7 Data 1 Stop Parity None 7 Data 1 Stop Parity Odd 7 Data 2 Stop Parity Odd 7 Data 2 Stop Parity Even 7 Data 2 Stop Parity None 8 Data 1 Stop Parity None 8 Data 1 Stop Parity Even 8 Data 1 Stop Parity Odd 2 10 RS 232 Handshaking RS 232 handshaking is a set
71. in a list of non continuous val ues Tag Field Usage When a query is used in place of a Tag field the query applies to the entire set of commands available for the particular storage table indicated by the Storage field of the command In this case the SubTag and Data fields should not be used because they are ignored by the device SubTag Field Usage When a query is used in place of a SubTag field the query applies only to the subset of commands available that match the Tag field In this case the Data field should not be used because it is ignored by the device Data Field Usage When a query is used in place of the Data field the query applies only to the specific command identified by the Tag and SubTag fields Concatenation of Multiple Commands Multiple commands can be issued within one Prefix Storage sequence Only the Tag SubTag and Data fields must be repeated for each command in the sequence If additional commands are to be applied to the same Tag then the new command sequence is separated with a comma and only the SubTag and Data fields of the additional command are issued If the additional com mand requires a different Tag field the command is separated from previous commands by a semicolon Responses The device responds to serial commands with one of three responses ACK Indicates a good command which has been processed ENQ Indicates an invalid Tag or SubTag command NAK Indicates the com
72. ing Points to Keep In Mind It is not necessary to build a message string The selections in this chapter are only used if you wish to alter the default settings Default prefix None Default suffix None A prefix or suffix may be added or cleared from one symbology or all symbologies You can add any prefix or suffix from the ASCII Conversion Chart Code Page 1252 on page A 3 plus Code I D and AIM I D You can string together several entries for several symbologies at one time Enter prefixes and suffixes in the order in which you want them to appear on the output To Add a Prefix or Suffix Step 1 Scan the Add Prefix or Add Suffix symbol page 4 3 Step 2 Determine the 2 digit Hex value from the Symbology Chart included in Appendix A for the symbology to which you want to apply the prefix or suffix For example for Code 128 Code ID is j and Hex ID is 6A Step 3 Scan the 2 hex digits from the Programming Chart inside the back cover of this manual or scan 9 9 for all symbologies Prefix Scanned Data Suffix 1 11 alpha numeric characters variable length 1 11 alpha numeric characters 4 2 Step 4 Determine the hex value from the ASCII Conversion Chart Code Page 1252 on page A 3 for the prefix or suffix you wish to enter Step 5 Scan the 2 digit hex value from the Programming Chart inside the back cover of this manual Step 6 Repeat Steps 4 and 5 for every prefi
73. ired all input data must conform to an edited for mat or the imager does not transmit the input data to the host device Alternate Data Formats Alternate formats allow you single shot capability to scan one bar code using a different data format than your primary format When data formats are pro grammed see page 5 1 you must input whether you are programming the pri mary format or an alternate format numbered 1 2 or 3 An alternate format is initiated by scanning one of the 3 alternate format bar codes below The imager will scan the next bar code formatting the data with the selected alternate format then revert immediately to the primary format Data Formatter Off Data Formatter On but Not Required Data Format On Format Required Alternate Data Format 1 Alternate Data Format 2 Alternate Data Format 3 5 6 6 1 6 Secondary Interface By switching secondary interface cables the 3800g imager for example can communicate with a portable data terminal secondary interface in addition to the host terminal primary interface See the table below for the secondary interfaces for the 3800g 3800g Models Enabling the Secondary Interface The secondary interface can be programmed at any time You can temporarily disable the secondary interface but still retain the second ary interface settings in the imager s memory by scanning the Disable bar code below To re enable the secondary interfac
74. l trig No Delay Short Delay 500 ms Medium Delay 1000 ms Long Delay 1500 ms User Specified Good Read Delay Manual Serial Trigger 3 4 ger command After scanning the Read Time Out bar code set the time out duration from 0 300 000 milliseconds by scanning digits from the inside back cover then scanning Save Default 30 000 Automatic Trigger The imager scans continuously using internal LEDs to detect bar codes Presentation Mode Presentation Mode uses ambient light to detect bar codes The LEDs are off for ambient conditions until a change occurs in the imager s field of view Then the LEDS turn on automatically to read the code If the light level in the room is not high enough Presentation Mode may not work properly Continuous Illumination Mode If you have several bar codes that are close together you may wish to have a continuous aiming beam on in order to properly aim the imager at one bar code Scan the Continuous Illumination On bar code to program the imager for this capability Once you have the aiming beam over the correct bar code pull the trigger to read the code Scan the Continuous Illumination Off bar code to turn off this feature Hands Free Time Out The Automatic Trigger and Presentation Modes are referred to as hands free modes If the imager s trigger is pulled when using a hands free mode the imager changes to manual trigger mode You can set the time the imager shou
75. ld remain in manual trigger mode by setting the Hands Free Time Out Once the time out value is reached if there have been no further trigger pulls the imager reverts to the original hands free mode Read Time Out Automatic Trigger Presentation Mode Continuous Illumination Mode On Continuous Illumination Mode Off 3 5 Scan the Hands Free Time Out bar code then scan the time out duration from 0 300 000 milliseconds from the inside back cover and Save Default 5 000 ms Reread Delay This sets the time period before the imager can read the same bar code a sec ond time Setting a reread delay protects against accidental rereads of the same bar code Longer delays are effective in minimizing accidental rereads at POS point of sale Use shorter delays in applications where repetitive bar code scanning is required Default Medium Reread Delay only works when in automatic trigger mode or presentation mode see page 3 4 User Specified Reread Delay If you want to set your own length for the reread delay scan the bar code below then set the delay from 0 30 000 milliseconds by scanning digits from the inside back cover then scanning Save Centering Window Use the centering feature to narrow the imager s field of view so the imager reads only the bar code you want When centering is turned on the imager only reads codes that intersect or are contained within the centering window you set up At least part o
76. ls Code 93 123456 9 Straight 2 of 5 Industrial 123456 Matrix 2 of 5 6543210 GS1 DataBar 01 00123456789012 Code 39 Codabar BC321 A13579B Micro PDF417 Test Message PDF417 Car Registration Programming Chart A C Save B Discard F E D Note If you make an error while scanning the letters or digits before scanning Save scan Discard scan the correct letters or digits and Save 0 2 6 1 7 5 4 3 8 9 Honeywell 700 Visions Drive P O Box 208 Skaneateles Falls NY 13153 0208 3800g UG Rev C 4 09
77. m aidc 2 Click in the Quick Search text box and enter Visual Xpress 3 Click on Search Now 4 Click on the entry for Visual Xpress 5 When prompted select Save File and save the files to the c windows temp directory 6 Once you have finished downloading the file exit the web site 7 Using Explorer go to the c windows temp file and unzip the file you saved 8 Double click on Setup exe and follow the screen prompts to install the Visual Xpress program 9 If you ve selected the defaults during installation you can click on Start Menu Programs Hand Held Products Visual Xpress 11 1 11 Serial Programming Commands The serial programming commands can be used in place of the programming bar codes Both the serial commands and the programming bar codes will pro gram the 3800g For complete descriptions and examples of each serial pro gramming command refer to the corresponding programming bar code in this manual The device must be set to an RS 232 interface see page 1 7 The following commands can be sent via a PC com port using terminal emulation software Conventions The following conventions are used for menu and query command descriptions parameterA label representing the actual value you should send as part of a command option An optional part of a command Data Alternatives in a command bold Names of menus menu commands buttons dialog boxes and windows that appear on the scr
78. mall hole on the side of the scanner s handle This is the cable release 4 Straighten one end of a paper clip 5 Insert the end of the paper clip into the small hole and press in This depresses the retention tab releasing the connector Pull the connector out while maintaining pressure on the paper clip then remove the paper clip 6 Replace with the new cable Insert the connector into the opening and press firmly The connector is keyed to go in only one way and will click into place Troubleshooting The scanner automatically performs self tests whenever you turn it on If your scanner is not functioning properly review the following Troubleshooting Guide to try to isolate the problem Is the power on Is the aiming beam line on If the aiming beam line isn t illuminated check that The cable is connected properly The host system power is on if external power isn t used The trigger works Cable Release 13 3 Is the scanner having trouble reading your symbols If the scanner isn t reading symbols well check that the symbols Aren t smeared rough scratched or exhibiting voids Aren t coated with frost or water droplets on the surface Are enabled in the scanner or in the decoder to which the scanner connects Is the bar code displayed but not entered The bar code is displayed on the host device correctly but you still have to press a key to enter it th
79. mand was good but the Data field entry was out of the allowable range for this Tag and SubTag combination e g an entry for a minimum message length of 100 when the field will only accept 2 characters When responding the device echoes back the command sequence with the status character inserted directly before each of the punctuation marks the period exclamation point comma or semicolon in the command 11 3 Examples of Query Commands In the following examples a bracketed notation depicts a non displayable response Example Example 1 What is the range of possible values for Codabar Coding Enable Enter cbrena Response CBRENA0 1 ACK This response indicates that Codabar Coding Enable CBRENA has a range of values from 0 to 1 off and on Example Example 2 What is the default value for Codabar Coding Enable Enter cbrena Response CBRENA1 ACK This response indicates that the default setting for Codabar Coding Enable CBRENA is 1 or on Example Example 3 What is the device s current setting for Codabar Coding Enable Enter cbrena Response CBRENA1 ACK This response indicates that the device s Codabar Coding Enable CBRENA is set to 1 or on Example Example 4 What are the device s settings for all Codabar selections Enter cbr Response CBRENA1 ACK SSX0 ACK CK20 ACK CCT1 ACK MIN2 ACK MAX60 ACK DFT ACK This response indicates that th
80. mild soapy water solu tion If a soapy water solution is used rinse with a clean lens tissue dampened with water only The scanner s housing may also be cleaned the same way Inspecting Cords and Connectors Inspect the scanner s interface cable and connector for wear or other signs of damage A badly worn cable or damaged connector may interfere with scanner operation Contact your Honeywell distributor for information about cable replacement Cable replacement instructions are on page 13 2 Caution Do not submerge the imager in water Do not use abrasive wipes or tissues on the imager s window abrasive wipes may scratch the window Never use solvents e g acetone benzene ether or phenol based agents on the housing or window solvents may damage the finish or the window 13 2 Replacing the Interface Cable The standard interface cable is attached to the scanner with an 10 pin modular connector When properly seated the connector is held in the 3800g scanner s handle by a flexible retention tab The interface cable is designed to be field replaceable Order replacement cables from Honeywell or from an authorized distributor When ordering a replacement cable specify the cable part number of the original interface cable To Replace the 3800g Interface Cable 1 Turn the power to the host system OFF 2 Disconnect the scanner s cable from the terminal or computer 3 Locate the s
81. mpliance with FCC Rules and Regulations cables connected to this device must be shielded cables UL Statement UL listed UL60950 1 for I T E product safety Canada Industry Canada ICES 003 This Class B digital apparatus complies with Canadian ICES 003 Operation is subject to the following conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Conformit la r glementation canadienne Cet appareil num rique de la Classe B est conforme la norme NMB 003 du Canada Son fonctionnement est assujetti aux conditions suivantes 1 Cet appareil ne doit pas causer de brouillage pr judiciable 2 Cet appareil doit pouvoir accepter tout brouillage re u y compris le brouillage pouvant causer un fonctionnement ind sirable cUL Statement cUL listed CSA C22 2 No 60950 1 03 for I T E product safety Europe The CE marking indicates compliance to 2004 108 EC EMC Directive with Standards EN55022 CLASS A EN55024 EN61000 3 2 EN61000 3 3 In addition complies to 2006 95 EC Low Voltage Directive when shipped with recommended power supply For CE related inquiries please contact Honeywell Imaging amp Mobility Europe BV Nijverheidsweg 9 5627 BT Eindhoven The Netherlands Honeywell shall not be liable for use of our product with equipment i e power supplies personal computers etc that is no
82. nal ID to 130 Note No extra configuration e g baud rate is necessary CTS RTS Emulation IBM SurePos USB Handheld Scanner Interface IBM SurePos USB Tabletop Scanner Interface USB HID Bar Code Scanner USB Com Port Emulation On Off 1 4 ACK NAK Mode Plug and Play Plug and Play bar codes provide instant imager set up for commonly used inter faces Note After you scan one of the codes power cycle the host terminal to have the interface in effect Connecting the Imager When Powered by Host Keyboard Wedge An imager can be connected between the keyboard and PC as a keyboard wedge plugged into the serial port or connected to a portable data terminal The following is an example of a keyboard wedge connection 1 Turn off power to the terminal computer 2 Disconnect the keyboard cable from the back of the terminal computer On Off 1 5 3 Connect the appropriate interface cable to the imager and to the terminal computer 4 Turn the terminal computer power back on Note You will not hear a power up beep because the 3800g is factory defaulted to a USB connection You must scan the IBM PC AT and Compatibles with CR suffix bar code on page 1 5 to enable keyboard wedge ability Verify the imager operation by scanning a bar code from the Sample Symbols in the back of this manual The imager beeps once Keyboard Wedge Connection Scanning the bar code below allows operation of
83. nd Maximum lengths 0 160 Minimum Default 1 Maximum Default 160 Code 49 lt Default All Code 49 Settings gt On Off Minimum Message Length Maximum Message Length 7 33 Code 49 Code 49 Message Length Scan the bar codes below to change the message length Refer to Message Length on page 7 2 for additional information Minimum and Maximum lengths 1 81 Minimum Default 1 Maximum Default 81 PDF417 3800gHD 3800gPDF only lt Default All PDF417 Settings gt PDF417 PDF417 Message Length Scan the barcodes below to change the message length Refer to Message Length page 7 2 for additional information Minimum and Maximum lengths 1 2750 Minimum Default 1 Maximum Default 2750 On Off Minimum Message Length Maximum Message Length Off On Maximum Message Length Minimum Message Length 7 34 MicroPDF417 3800gHD 3800gPDF only lt Default All MicroPDF417 Settings gt MicroPDF417 MicroPDF417 Message Length Scan the barcodes below to change the message length Refer to Message Length page 7 2 for additional information Minimum and Maximum lengths 1 366 Minimum Default 1 Maximum Default 366 GS1 Composite Codes Linear codes are combined with a unique 2D composite component to form a new class called GS1 Composite symbology GS1 Composite symbologies allow for the co existence of symbologies already in use Default Off Off On Maximum M
84. nly Off LBLENA0 7 36 On LBLENA1 7 36 TCIF Linked Code 39 TLC39 3800gHD 3800gPDF only Off T39ENA0 7 36 On T39ENA1 7 36 Selection Setting Indicates default Serial Command Indicates a numeric entry Page 11 20 12 1 12 Product Specifications 3800g Product Specifications Parameter Specification Dimensions Typical Height 5 9 inches 15 cm Length 4 4 inches 11 2 cm Width 3 1 inches 7 9 cm Weight 5 6 ounces 160 g Light Source 630 nm visible red LED 800 W max radiant power Scan Rate 270 scans per second in most usages Skew Angle 65 degrees Pitch Angle 65 degrees Horizontal Velocity 20 inches 50 cm per second Scan Contrast 20 minimum Voltage Requirements 3800GX4E 4 5 5 5VDC at imager 3800GX5E 4 5 12VDC at imager Current Draw Max Scanning Standby Inrush 3800GX4E 3800GX5E 5Vdc 250mA 87mA 380mA 3800GX5E 12VDC 126mA 50mA N A Temperature Ranges Operating 32 F to 122 F 0 C to 50 C Storage 40 F to 140 F 40 C to 60 C Humidity 0 to 95 non condensing Mechanical Drop Operational after 50 drops from 5 feet 1 5 m to concrete Vibration Withstands 5G peak from 22 to 300 Hz ESD Sensitivity 15 kV to any external surface Sealant Rating IP41 Power Sources Requirements Host powered options available e g USB 12VDC adapter Use only a UL cUL listed power supply wit
85. o the Honey well USB Application Note available at www honeywell com aidc USB PC or Macintosh Keyboard The 3800g imagers are factory programmed for a USB interface If this is your interface and you do not need to modify the settings skip to Chapter 3 If you programmed the imager for a different terminal interface and you want to change to a USB Keyboard PC or USB Keyboard Mac scan one of the fol lowing codes to program the 3800g Scanning these codes adds a CR and selects the terminal ID USB PC Keyboard 124 USB Macintosh Keyboard 125 USB Keyboard PC USB Keyboard Mac 1 3 IBM SurePos Scan one of the following Plug and Play codes to program the 3800gX5 for IBM SurePos USB Handheld imager or IBM SurePos USB Tabletop imager Note After scanning one of these codes you must power cycle the cash register USB HID Scan the following code to program the 3800g for USB HID bar code scanners Scanning this code changes the terminal ID to 131 USB Com Port Emulation Scan the following code to program the 3800g to emulate a regular RS 232 based Com Port If you are using a Microsoft Windows PC you will need to download a driver from the Honeywell website www honeywell com aidc The driver will use the next available Com Port number Apple Macintosh comput ers recognize the imager as a USB CDC class device and automatically uses a class driver Scanning the code below changes the termi
86. oding is enabled certain character pairs within the bar code symbol will be interpreted as a single character For example V will be decoded as the ASCII character SYN and C will be decoded as the ASCII character Default Off NUL U DLE P SP SPACE 0 0 V P P W p P SOH A DC1 Q A 1 1 A A Q Q a A q Q STX B DC2 R B 2 2 B B R R b B r R ETX C DC3 S C 3 3 C C S S c C s S EOT D DC4 T D 4 4 D D T T d D t T ENQ E NAK U E 5 5 E E U U e E u U ACK F SYN V amp F 6 6 F F V V f F v V BEL G ETB W G 7 7 G G W W g G w W BS H CAN X H 8 8 H H X X h H x X HT I EM Y I 9 9 I I Y Y i I y Y LF J SUB Z J Z J J Z Z j J z Z VT K ESC A K F K K K k K P FF L FS B L lt G L L L l L Q CR M GS C H M M M m M R SO N RS D gt I N N N n N S SI O US E O J O O _ O o O DEL T Off On 7 8 Character pairs M and N decode as a minus sign and period respectively Character pairs P through Y decode as 0 through 9 Code 39 Code Page Code pages define the mapping of character codes to characters If the data received does not display with the proper characters it may b
87. of rules concerning the exchange of data between serially communicating devices Default RTS CTS XON XOFF and ACK NAK Off RTS CTS On XON OFF Off RTS CTS Off XON XOFF On ACK NAK On ACK NAK Off 3 1 3 Output Good Read Indicators Beeper Good Read The beeper may be programmed On or Off in response to a good read Turning this option off only turns off the beeper response to a good read indication All error and menu beeps are still audible Default On Beeper Volume Good Read The beeper volume codes modify the volume of the beep the imager emits on a good read Default High for the 3800g Beeper Pitch Good Read The beeper pitch codes modify the pitch frequency of the beep the imager emits on a good read Default Medium On Off High Medium Off Low Low 1600 Hz Medium 2550 Hz High 4200 Hz 3 2 Beeper Duration Good Read The beeper duration codes modify the length of the beep the imager emits on a good read Default Normal LED Good Read The LED indicator can be programmed On or Off in response to a good read Default On Number of Beeps Good Read The number of beeps of a good read can be programmed from 1 9 The same number of beeps will be applied to the beeper and LED in response to a good read For example if you program this option to have five beeps there will be five beeps and five LED flashes in response to
88. om Port 130 USB HIDPOS 131 Supported Terminals Continued Terminal Model s Terminal ID 2 4 Keyboard Country Scan the appropriate country code below to program the keyboard for your country As a general rule the following characters are supported but need special care for countries other than the United States lt gt United States Denmark France Germany Austria Great Britain Italy Norway Spain Switzerland Belgium Finland 2 5 Please refer to Honeywell website www honeywell com aidc for complete key board country support information and applicable interfaces If you need to pro gram a keyboard for a country other than one listed above scan the Program Keyboard Country bar code below then scan the numeric bar code s for the appropriate country from the inside back cover then the Save bar code Keyboard Style This programs keyboard styles such as Caps Lock and Shift Lock Default Regular Regular is used when you normally have the Caps Lock key off Caps Lock is used when you normally have the Caps Lock key on Shift Lock is used when you normally have the Shift Lock key on not common to U S keyboards Automatic Caps Lock is used if you change the Caps Lock key on and off The software tracks and reflects if you have Caps Lock on or off AT and PS 2 only This selection can only be used with systems that have an LED which notes the Cap
89. p Code 128 Label Code 3800gHD 3800gPDF only UPC A EAN 13 with Extended Coupon Code Telepen EAN JAN 8 Trioptic Code GS1 DataBar Omnidirectional UPC A GS1 DataBar Limited UPC E GS1 DataBar Expanded Straight 2 of 5 IATA two bar start stop Interleaved 2 of 5 Straight 2 of 5 Industrial three bar start stop 7 2 All Symbologies If you want to decode all the symbologies allowable for your imager scan the All Symbologies On code If on the other hand you want to decode only a particular symbology scan All Symbologies Off followed by the On symbol for that particular symbology Message Length You are able to set the valid reading length of some of the bar code symbologies If the data length of the scanned bar code doesn t match the valid reading length the imager will issue an error beep You may wish to set the same value for minimum and maximum length to force the imager to read fixed length bar code data This helps reduce the chances of a misread EXAMPLE Decode only those bar codes with a count of 9 20 characters Min length 09 Max length 20 EXAMPLE Decode only those bar codes with a count of 15 characters Min length 15 Max length 15 For a value other than the minimum and maximum message length defaults scan the bar codes included in the explanation of the symbology then scan the digit value of the message leng
90. ps from the top of the bar code to the bottom and back up This ensures that the entire code is scanned Good Technique Bad Technique Bad Technique 1 9 Resetting the Standard Product Defaults If you aren t sure what programming options are in your imager or you ve changed some options and want the factory settings restored scan the Stan dard Product Default Settings bar code below The Menu Commands starting on page 11 5 lists the factory default settings for each of the commands indicated by an asterisk on the programming pages Standard Product Default Settings 1 10 2 1 2 Terminal Interfaces Terminal ID If your interface is not a standard PC AT refer to Terminal ID beginning on page 2 1 and locate the Terminal ID number for your PC Scan the Terminal ID bar code below then scan the numeric bar code s from the Programming Chart inside the back cover of this manual to program the imager for your terminal ID Scan Save to save your selection For example an IBM AT terminal has a Terminal ID of 003 You would scan the Terminal ID bar code then 0 0 3 from the Programming Chart inside the back cover of this manual then Save If you make an error while scanning the digits before scanning Save scan the Discard code on the Programming Chart scan the Terminal ID bar code scan the digits and the Save code again Note After scanning one of these codes you must power cycle your computer
91. ramming Chart inside the back cover of this manual to save your entries Other Programming Selections Clear One Data Format This deletes one data format for one symbology If you are clearing the primary format scan 0 from the Programming Chart inside the back cover of this manual If you are clearing an alternate format scan 1 2 or 3 depending on the alternate format you are clearing Scan the Terminal Type refer to the Supported Terminals Chart on page 2 2 Code I D refer to the Symbology Chart on page A 1 and the bar code data length for the specific data format that you want to delete All other formats remain unaffected Save from the Programming Chart inside the back cover of this manual This exits saving any Data Format changes Discard from the Programming Chart inside the back cover of this manual This exits without saving any Data Format changes Data Format Editor Commands Send Commands F1 Send all characters followed by xx key or function code starting from cur rent cursor position Syntax F1xx xx stands for the hex value for an ASCII code see ASCII Conversion Chart Code Page 1252 on page A 3 F2 Send nn characters followed by xx key or function code starting from current cursor position Syntax F2nnxx nn stands for the numeric value 5 3 00 99 for the number of characters and xx stands for the hex value for an ASCII code See ASCII Conversion Chart Code Page 1252 on
92. rs all current prefixes then programs a Code I D prefix for all symbologies This is a temporary setting that will be removed when the unit is power cycled Show Software Revision Scan the bar code below to output the current software revision unit serial num ber and other product information Show Data Format Scan the bar code below to show current data format settings Resetting the Standard Product Defaults If you aren t sure what programming options are in your imager or you ve changed some options and want the standard product default settings restored scan the Standard Product Default Settings bar code below The Menu Commands starting on page 11 5 lists the standard product default settings for each of the commands indicated by an asterisk on the program ming pages Add Code I D Prefix to All Symbologies Temporary Show Revision Data Format Settings Standard Product Default Settings 9 2 Temporary Visual Xpress Configuration For quick download communication configuration scan the Visual Xpress bar code to temporarily configure the imager for Visual Xpress settings Refer to Visual Xpress on page 10 1 for additional information about Visual Xpress Note If you have a unit capable of keyboard wedge mode scan the bar code below and the unit will communicate in RS 232 mode allowing it to work with Visual Xpress To convert the imager back to keyboard wedge communication cycle the power
93. rs at certain points in bar code data as it is scanned The selections in the following pages are used only if you wish to alter the output Default Data Format setting None Normally when you scan a bar code it gets outputted automatically however when you do a format you must use a send command see Send Commands on page 5 2 within the format program to output data Multiple formats may be programmed into the imager They are stacked in the order in which they are entered However the following list presents the order in which formats are applied 1 Specific Term ID Actual Code ID Actual Length 2 Specific Term ID Actual Code ID Universal Length 3 Specific Term ID Universal Code ID Actual Length 4 Specific Term ID Universal Code ID Universal Length 5 Universal Term ID Actual Code ID Actual Length 6 Universal Term ID Actual Code ID Universal Length 7 Universal Term ID Universal Code ID Actual Length 8 Universal Term ID Universal Code ID Universal Length If you have changed data format settings and wish to clear all formats and return to the factory defaults scan the Default Data Format code on page 5 4 To Add a Data Format Step 1 Scan the Enter Data Format symbol page 5 4 Step 2 Primary Alternate Format Determine if this will be your primary data format or one of 3 alternate formats Alternate formats allow you single shot capability to scan one bar code using a different data format
94. s 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio or television technician for help Caution Any changes or modifications made to this equipment not expressly approved by Honeywell International Inc may void the FCC authorization to operate this equipment Note To maintain co
95. s Lock status Autocaps via NumLock bar code should be scanned in countries e g Ger many France where the Caps Lock key cannot be used to toggle Caps Lock The NumLock option works similarly to the regular Auotcaps but uses the Num Lock key to retrieve the current state of the Caps Lock Program Keyboard Country Regular Caps Lock Shift Lock Automatic Caps Lock Autocaps via NumLock 2 6 Emulate External Keyboard should be scanned if you do not have an external keyboard IBM AT or equivalent Note After scanning the Emulate External Keyboard bar code you must power cycle your computer Keyboard Modifiers This modifies special keyboard features such as CTRL ASCII codes and Turbo Mode Control ASCII Mode On The imager sends key combinations for ASCII control characters for values 00 1F Windows is the preferred mode All key board country codes are supported DOS mode is a legacy mode and it does not support all keyboard country codes New users should use the Windows mode Refer to Keyboard Function Relationships page 8 1 for CTRL ASCII Values Default Off Turbo Mode The imager sends characters to a terminal faster If the terminal drops characters do not use Turbo Mode Default Off Emulate External Keyboard Windows Mode Control ASCII Mode On Control ASCII Mode Off DOS Mode Control ASCII Mode On Turbo Mode On Turbo Mode Off 2 7 Numeric Keypad Mode Sends numer
96. s default Serial Command Indicates a numeric entry Page 11 7 Word Length Data Bits Stop Bits and Parity 7 Data 1 Stop Parity Even 232WRD3 2 9 7 Data 1 Stop Parity None 232WRD0 2 9 7 Data 1 Stop Parity Odd 232WRD6 2 9 7 Data 2 Stop Parity Even 232WRD4 2 9 7 Data 2 Stop Parity None 232WRD1 2 9 7 Data 2 Stop Parity Odd 232WRD7 2 9 8 Data 1 Stop Parity Even 232WRD5 2 9 8 Data 1 Stop Parity None 232WRD2 2 9 8 Data 1 Stop Parity Odd 232WRD8 2 9 RS 232 Handshaking RTS CTS Off 232CTS0 2 10 RTS CTS On 232CTS1 2 10 XON XOFF Off 232XON0 2 10 XON XOFF On 232XON1 2 10 ACK NAK Off 232ACK0 2 10 ACK NAK On 232ACK1 2 10 Output Selections Beeper Good Read Off BEPBEP0 3 1 On BEPBEP1 3 1 Beeper Volume Good Read Off BEPLVL0 3 1 Low BEPLVL1 3 1 Medium BEPLVL2 3 1 High BEPLVL3 3 1 Selection Setting Indicates default Serial Command Indicates a numeric entry Page 11 8 Beeper Pitch Good Read Frequency Low 1600 min 400Hz BEPFQ116 00 3 1 Medium 2550 BEPFQ125 50 3 1 High 4200 max 9000Hz BEPFQ142 00 3 1 Beeper Duration Good Read Normal Beep BEPBIP0 3 2 Short Beep BEPBIP1 3 2 LED Good Read Off BEPLED0 3 2 On BEPLED1 3 2 Number of Beeps Good Read 1 BEPRPT1 3 2 Range 1 9 BEPRPT 3 2 Good Read Delay No Delay DLYGRD0 3 3
97. s set to on the imager will only read EAN JAN 13 bar codes that have addenda Default Not Required On Off Off On 5 Digit Addenda Off 5 Digit Addenda On 2 Digit Addenda Off 2 Digit Addenda On Not Required Required 7 23 EAN JAN 13 Addenda Separator When this feature is on there is a space between the data from the bar code and the data from the addenda When turned off there is no space Default On Note If you want to enable or disable EAN13 with Extended Coupon Code refer to UPC A EAN 13 with Extended Coupon Code on page 7 19 ISBN Translate This selection causes EAN 13 Bookland symbols to be translated into their equivalent ISBN number format Default Off EAN JAN 8 lt Default All EAN JAN 8 Settings gt Off On Off On 7 24 EAN JAN 8 EAN JAN 8 Check Digit This selection allows you to specify whether the check digit should be transmit ted at the end of the scanned data or not Default On EAN JAN 8 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN JAN 8 data Default Off for both 2 Digit and 5 Digit Addenda EAN JAN 8 Addenda Required When Addenda Required is set to on the imager will only read EAN JAN 8 bar codes that have addenda Default Not Required On Off Off On 5 Digit Addenda Off 5 Digit Addenda On 2 Digit Addenda Off 2 Digit Addenda On Not Required Required 7 25 EAN
98. symbol having a D stop character In this case the two messages are concat enated into one with the D characters omitted Select Require to prevent the imager from decoding a single D Codabar sym bol without its companion This selection has no effect on Codabar symbols without Stop Start D characters No Check Character Validate Modulo 16 and Transmit Validate Modulo 16 but Don t Transmit A12D D34A Codabar Character Stop Start Stop Start On Off Require 7 5 Codabar Message Length Scan the bar codes below to change the message length Refer to Message Length on page 7 2 for additional information Minimum and Maximum lengths 2 60 Minimum Default 4 Maximum Default 60 Code 39 lt Default All Code 39 Settings gt Code 39 Code 39 Start Stop Characters Start Stop characters identify the leading and trailing ends of the bar code You may either transmit or not transmit Start Stop characters Default Don t Transmit Code 39 Check Character No Check Character indicates that the imager reads and transmits bar code data with or without a check character When Check Character is set to Validate but Don t Transmit the unit only reads Code 39 bar codes printed with a check character but will not transmit the check character with the scanned data Minimum Message Length Maximum Message Length On Off Transmit Don t Transmit 7 6 When Ch
99. t CE marked and does not comply with the Low Voltage Directive Waste Electrical and Electronic Equipment Information Honeywell complies with Directive 2002 96 EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 27 January 2003 on waste electrical and electronic equipment WEEE This product has required the extraction and use of natural resources for its production It may contain hazardous substances that could impact health and the environment if not properly disposed In order to avoid the dissemination of those substances in our environment and to diminish the pressure on the natural resources we encourage you to use the appropriate take back systems for product disposal Those systems will reuse or recycle most of the materials of the product you are disposing in a sound way The crossed out wheeled bin symbol informs you that the product should not be disposed of along with municipal waste and invites you to use the appropriate separate take back systems for product disposal If you need more information on the collection reuse and recycling systems please contact your local or regional waste administration You may also contact your supplier for more information on the environmental performances of this product Germany GS Mark Applicable if GS logo is marked on product to indicate meeting geprufte Sicherheit approval Australia NZ C Tick Statement Conforms to AS NZS 3548 EMC requirements South Korea MIC Cl
100. t stop lt Default All Code IATA 2 of 5 Settings gt Straight 2 of 5 IATA On Off Minimum Message Length Maximum Message Length On Off 7 12 Straight 2 of 5 IATA Message Length Scan the bar codes below to change the message length Refer to Message Length on page 7 2 for additional information Minimum and Maximum lengths 1 48 Minimum Default 4 Maximum Default 48 Matrix 2 of 5 lt Default All Matrix 2 of 5 Settings gt Matrix 2 of 5 Matrix 2 of 5 Message Length Scan the bar codes below to change the message length Refer to Message Length on page 7 2 for additional information Minimum and Maximum lengths 1 80 Minimum Default 4 Maximum Default 80 Minimum Message Length Maximum Message Length On Off Minimum Message Length Maximum Message Length 7 13 Code 11 lt Default All Code 11 Settings gt Code 11 Check Digits Required This option sets whether 1 or 2 check digits are required with Code 11 bar codes Default Two Check Digits On Off One Check Digit Two Check Digits 7 14 Code 11 Message Length Scan the bar codes below to change the message length Refer to Message Length on page 7 2 for additional information Minimum and Maximum lengths 1 80 Minimum Default 4 Maximum Default 80 Code 128 lt Default All Code 128 Settings gt Code 128 ISBT 128 Concatenation In 1994 the International Society of Blood Transfusion I
101. ta Suffix Intercharacter Delay Delay Length Character to Trigger Delay 4 6 Interfunction Delay An interfunction delay of up to 495 milliseconds may be placed between the transmission of each segment of the message string Scan the Interfunction Delay bar code below then scan the number of milliseconds and the Save bar code using the Programming Chart inside the back cover of this manual To remove this delay scan the Interfunction Delay bar code then set the num ber of steps to 0 Scan the Save bar code using the Programming Chart inside the back cover of this manual Intermessage Delay An intermessage delay of up to 495 milliseconds may be placed between each scan transmission Scan the Intermessage Delay bar code below then scan the number of milliseconds and the Save bar code using the Programming Chart inside the back cover of this manual To remove this delay scan the Intermessage Delay bar code then set the number of steps to 0 Scan the Save bar code using the Programming Chart inside the back cover of this manual Interfunction Delays Prefix Scanned Data Suffix 1 2 3 4 5 STX HT CR LF Interfunction Delay 2nd Scan Transmission 1st Scan Transmission Intermessage Delay Intermessage Delay 5 1 5 Data Formatting Data Format Editor Introduction You may use the Data Format Editor to change the imager s output For exam ple you can use the Data Format Editor to insert characte
102. terminal must match for correct data transfer through the serial port using RS 232 protocol Scanning the RS 232 interface bar code programs the imager for an RS 232 interface at 38 400 baud parity none 8 data bits 1 stop bit and adds a suffix of a CR LF Refer to page 2 8 for additional RS 232 configuration settings IBM 4683 Ports 5B 9B and 17 Interface Scan one of the following Plug and Play codes to program the 3800GX5E for IBM 4683 Port 5B 9B or 17 Note After scanning one of these codes you must power cycle the cash register RS 232 Interface IBM 4683 Port 5B Interface IBM 4683 Port 9B HHBCR 1 Interface IBM 4683 Port 17 Interface IBM 4683 Port 9B HHBCR 2 Interface 1 8 Reading Techniques The imager has a bright red aiming beam that corresponds to its horizontal field of view The aiming beam should be centered horizontally over the bar code it will not read if the aiming beam is in any other direction The best focus point for reading most code densities is about 5 inches 12 7 cm from the unit To read a single bar code or multiple bar codes on a page or on an object hold the imager at an appropriate distance from the target pull the trigger and center the aiming beam on the bar code Reading PDF417 Bar Codes Note Applies to 3800gHD and 3800gPDF To read PDF417 bar codes with a PDF enabled 3800gHD 3800gPDF hold the trigger down and move the scanner up and down so the aiming line swee
103. th and Save bar codes on the Programming Chart inside the back cover of this manual The minimum and maximum lengths and the defaults are included with the respective symbologies All Symbologies On All Symbologies Off 7 3 Codabar lt Default All Codabar Settings gt Codabar Codabar Start Stop Characters Start Stop characters identify the leading and trailing ends of the bar code You may either transmit or not transmit Start Stop characters Default Don t Transmit Codabar Check Character Codabar check characters are created using different modulos You can pro gram the imager to read only Codabar bar codes with Modulo 16 check charac ters Default No Check Character No Check Character indicates that the imager reads and transmits bar code data with or without a check character When Check Character is set to Validate and Transmit the imager will only read Codabar bar codes printed with a check character and will transmit this character at the end of the scanned data On Off Transmit Don t Transmit 7 4 When Check Character is set to Validate but Don t Transmit the unit will only read Codabar bar codes printed with a check character but will not transmit the check character with the scanned data Codabar Concatenation Codabar supports symbol concatenation When you enable concatenation the imager looks for a Codabar symbol having a D start character adjacent to a
104. the ASCII Conversion Chart Code Page 1252 page A 3 find the Hex value that represents the character s you want to match Use the Program ming Chart to read the alphanumeric combination that represents the ASCII characters 99 is the Universal number indicating all characters 5 End Output Sequence Editor Scan F F to enter an Output Sequence for an additional symbology or Save to save your entries Other Programming Selections 3 9 Discard This exits without saving any Output Sequence changes Output Sequence Editor Require Output Sequence When an output sequence is Required all output data must conform to an edited sequence or the imager will not transmit the output data to the host device When it s On Not Required the imager will attempt to get the output data to conform to an edited sequence but if it cannot the imager transmits all output data to the host device as is When the output sequence is Off the bar code data is output to the host as the imager decodes it Note This selection is unavailable when the Multiple Symbols Selection is turned on Enter Sequence Default Sequence Required On Not Required Off 3 10 Output Sequence Example In this example you are scanning Code 93 Code 128 and Code 39 barcodes but you want the image scanner to output Code 39 1st Code 128 2nd and Code 93 3rd as shown below Note Code 93 must be enabled to use this example You would set up
105. x or suffix character Step 7 To add the Code I D scan 5 C 8 0 To add AIM I D scan 5 C 8 1 To add a backslash scan 5 C 5 C Note To add a backslash as in Step 7 you must scan 5C twice once to create the leading backslash and then to create the backslash itself Step 8 Scan Save to exit and save or scan Discard to exit without saving Repeat Steps 1 6 to add a prefix or suffix for another symbology Example Add a Suffix to a specific symbology To send a CR carriage return Suffix for UPC only Step 1 Scan Add Suffix Step 2 Determine the 2 digit hex value from the Symbology Chart included in the ASCII Conversion Chart Code Page 1252 on page A 3 for UPC Step 3 Scan 6 3 from the Programming Chart inside the back cover of this manual Step 4 Determine the hex value from the ASCII Conversion Chart Code Page 1252 on page A 3 for the CR carriage return Step 5 Scan 0 D from the Programming Chart inside the back cover of this manual Step 6 Scan Save or scan Discard to exit without saving To Clear One or All Prefixes or Suffixes You can clear a single prefix or suffix or clear all prefixes suffixes for a symbol ogy When you Clear One Prefix Suffix the specific character you select is deleted from the symbology you want When you Clear All Prefixes Suffixes all the prefixes or suffixes for a symbology are deleted Step 1 Scan the Clear One Prefix or Clear One Suffix s
106. ymbol Step 2 Determine the 2 digit Hex value from the Symbology Chart included in Appendix A for the symbology from which you want to clear the prefix or suffix 4 3 Step 3 Scan the 2 digit hex value from the Programming Chart inside the back cover of this manual or scan 9 9 for all symbologies Your change is automatically saved To Add a Carriage Return Suffix to All Symbologies Scan the following bar code if you wish to add a carriage return suffix to all sym bologies at once This action first clears all current suffixes then programs a carriage return suffix for all symbologies Prefix Selections Add CR Suffix All Symbologies Add Prefix Clear One Prefix Clear All Prefixes 4 4 Suffix Selections Function Code Transmit When this selection is enabled and function codes are contained within the scanned data the imager transmits the function code to the terminal Charts of these function codes are provided in Supported Interface Keys starting on page 8 3 When the imager is in keyboard wedge mode the scan code is con verted to a key code before it is transmitted Default Enable Intercharacter Interfunction and Intermessage Delays Some terminals drop information characters if data comes through too quickly Intercharacter interfunction and intermessage delays slow the transmission of data increasing data integrity Each delay is composed of a 5 millisecond step You can program up to 9

Download Pdf Manuals

Related Search

Related Contents

Samsung SPF-83M User Manual  CopyD command  Smart Objects Integration Kit User Guide  

Copyright © All rights reserved. Failed to retrieve file