Philips 32PFL3404D 32" HD-Ready 3D compatibility Black
Contents
1. 26 EN Reorder channels After you install channels you can rearrange the order in which they appear When watching T V press OK to display the channel grid Press OPTIONS L gt The channel options menu appears G N Press AY to select Reorder and then OK to return to the channel grid Press amp lt 4P to select the channel you want to reorder and press OK L gt The selected channel is highlighted g Press AY to move the highlighted channel to your preferred position 6 Press OPTIONS Done reordering appears on the screen 7 Press OK to finish reordering Test digital reception If using digital broadcasts you can check the quality and signal strength of digital channels This allows you to reposition and test your antenna or satellite dish Press amp MENU 2 Press AY 4b to select Setup gt Installation gt Channel install gt Digital test recept Press OK or P to enter the menu Press AY 4b to enter the frequency of the channel you want to test Press OK to confirm the frequency and then press OK again to confirm Search OV U1 Aw When complete select Store to store the frequency Ifthe signal quality and strength is poor reposition the antenna or satellite dish and retest f you still have problems with the reception of your digital broadcast contact a specialised installer 7 Connect devices This section des2. 7 Connect devices 27 Back connector for 19 22 inch TV 27 Back connector for 26 inch TV and larger 29 Side connector 30 Connect a computer 31 Use a Conditional Access Module 32 Use Philips EasyLink 32 Use a Kensington lock 33 8 Product information 34 Supported display resolutions 34 Multimedia 34 Tuner Reception Transmission 34 Remote control 34 Power 34 Supported V mounts 34 9 Troubleshooting 35 General TV Issues 25 TV channel issues 35 Picture issues 35 Sound issues 36 HDMI connection issues 36 Computer connection issues 36 Contact us 36 10 Index 37 EN 1 English 1 Notice 2009 Koninklijke Philips Electronics N V Al rights reserved Specifications are subject to change without notice Trademarks are the property of Koninklijke Philips Electronics N V or their respective owners Philips reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly The material in this manual is believed adequate for the intended use of the system If the product or its individual modules or procedures are used for purposes other than those specified herein confirmation of their validity and suitability must be obtained Philips warrants that the material itself does not infringe any United States patents No further warranty is expressed or implied Warranty Risk of injury damage to TV or void of warranty Never attempt to repair the TV yourself e Use t
3. get set for digital V EN 39 Digital UK the body leading the digital TV switchover will advise you when you need to re tune during the switchover If you choose to connect your TV to satellite or cable with a digital box then it will not be affected by switchover and you won t need to re tune If you have any questions please contact your equipment supplier or call Digital UK on 0845 6 50 50 50 or visit www digitaluk co uk How to re tune To find out how to re tune your TV check this user manual for details Go to section 6 Install channels If you do not re tune your channels when advised to do so by Digital UK you may lose some or all of your channels until you do re tune You should re tune your TV every few months to check for any new channels If you are missing any channels it may be that they are not available in your area or that your aerial needs upgrading When does switchover happen Copeland switches on October 17 2007 Visit us at digitaluk co uk Call us on 0845 6 50 50 501 t Calls charged at BT rate of 3p per minute daytime and 1p per minute evenings and weekends Rates may vary for calls from non BT lines 40 EN ar NS A Y Shetland Islands STV North 2010 v STV Central 2010 11 Central Anglia oii 2011 London 2012 Meridian 2012 WEICH 2009 10 West Country 2009 PHILIPS 2009 Koninklijke Philips Electronics N V All rights rese
4. es Your product is designed and manufactured with high quality materials and components which can be recycled and reused A When this crossed out wheeled bin symbol Is attached to a product it means that the product is covered by the European Directive 2002 96 EC Please inform yourself about the local separate collection system for electrical and electronic products Please act according to your local rules and do not dispose of your old products with your normal household waste Correct disposal of your old product helps to prevent potential negative consequences for the environment and human health R Your product contains batteries covered by the European Directive 2006 66 EC which cannot be disposed with normal household waste Please inform yourself about the local rules on separate collection of batteries because correct disposal helps to prevent negative consequences for the environmental and human health EN 5 English 3 TV overview Remote control This section gives you an overview of commonly used V controls and functions Side controls and indicators SOS 4 POWER Switches the product on or off The product is not powered off completely unless it is physically unplugged P CH Switches to the next or previous channel G SOURCE Selects connected devices 4 VOLUME Increases or decreases volume gt PHILIPS
5. Dual I II Selects between audio languages if dual sound is broadcast Mono Stereo Selects between mono or stereo if stereo is broadcast TV speakers Turns TV speakers on or off Surround Enables spatial sound Auto volume Automatically reduces sudden volume changes for example when switching channels When enabled this produces a more consistent audio volume Delta volume Levels out volume differences between channels or connected devices Switch to the connected device before you change the delta volume Use advanced teletext features Access the teletext options menu Most of the advanced teletext features are accessed via the teletext options menu 1 Press MHEG TELETEXT L gt The teletext screen appears 2 Press OPTIONS L gt The teletext options menu appears 3 Press AV to select one of the following options Freeze page Freezes the current page e Dual Full screen Enables and disables dual screen teletext which splits the current channel or source to the left of the screen with teletext on the right Reveal Hides or reveals hidden information on a page such as solutions to riddles or puzzles Cycle subpage Cycles through subpages automatically if subpages are available Language Switches to a different language group to display a language correctly when that language uses a different character set Press OK to confirm your choice 5 Press MHEG TELETEXT
6. Enables or disables subtitles DEMO Toggles the demonstration menu on or off Q1 FORMAT Selects a picture format Q2 lt INCR SURR Enables Incredible Surround for stereo sources Enables spatial mode for mono sources EN English 4 Use your product This section helps you perform basic operations see Use more of your product on page 10 Switch your TV on off or to standby To switch on Ifthe standby indicator is off press POWER at the side of the TV e Ifthe standby indicator is red press Standby On on the remote control To switch to standby Press Standby On on the remote control L gt The standby indicator switches to red To switch off Press OPOWER at the side of the TV L gt The standby indicator switches off Ea Though your TV consumes very little power when in standby energy continues to be consumed When not in use for an extended period of time disconnect the TV power cable from the power outlet f you cannot locate your remote control and want to switch on the TV from standby press P CH or SOURCE at the side of the TV Switch channels GIGS G3 G3 C9 SOUND PICTURE es at 1 1 1 s P CH a e Press P on the remote control or P CH on the side of the TV e Enter a channel number using the Numeric buttons
7. GUIDE to switch between thumbnail and file browsing views 3 Press AVP to select music or a music album Press OK to play the selected music Music settings When listening to music press OPTIONS to access one of the following music settings e Start Stop play Repeat Play once e Shuffle on off e Show info TV speakers Disconnect a USB storage device Caution Follow this procedure to avoid damage to your USB storage device 1 Press gt BACK to exit the USB browser 2 Wait for five seconds before you disconnect the USB storage device Listen to digital radio channels If digital broadcasting is available digital radio channels are installed automatically during installation 1 when watching T V press OK to display the channel grid 2 Press OPTIONS 3 Press AV to select Filter channels gt Radio L gt The radio channel grid appears 4 Press AY4b to select a radio channel and press OK to listen Select Filter channels gt All to exit radio channels and view all channels Update the TV software Philips continuously tries to improve its products and we recommend that you update the TV software when updates are available Check www philips com support for availability Check the current software version 1 Press amp MENU 2 Press Av to select Setup gt Software update gt Current software L gt The V displays the current s
8. can exit a favourite list and view all installed channels 1 when watching T V press OK to display the channel grid 2 Press OPTIONS L gt The channel options menu appears Press AY to select Show fav ch gt All Press OK Ly All channels are displayed in the channel grid All favourite channels will be marked by an asterisk when you view the channel grid Add a channel to a favourite list E e View all channels before adding a channel to a favourite list 1 when watching TV press OK to display the channel grid N Press amp lt 4P to select a channel you want to add to a favourite list J Press OPTIONS L gt The channel options menu appears 4 Press AY to select Mark as favourite and press OK L gt The favourite lists appear 5 Press AV to select a favourite list to add the channel to 6 Press OK Ly The channel is added to the favourite list Tip When watching TV save the current channel in a favourite list by pressing OPTIONS gt Mark as favourite Remove a channel from a favourite list Note Select the favourite list to edit before removing a channel 1 When watching TV press OK to display the channel grid 2 Press OPTIONS L gt The channel options menu appears 3 Press AV to select Show fav ch and press OK 4 Press AV to select a favourite list and press OK to edit L gt The favourite ch
9. damage both the CAM and your T V 1 Switch off the TV 2 Following the directions printed on the CAM gently insert the CAM into the COMMON INTERFACE at the side of the TV 3 Push the CAM in as far as it wil go 4 Tum on the TV and wait for the CAM to be activated This may take several minutes Do not remove the CAM from the slot when in use removing the CAM will deactivate digital services COMMON INTERFACE 32 EN Access CAM services 1 After inserting and activating the CAM press ft MENU 2 Press Av to select Setup gt Features gt Common interface L gt Applications provided by the digital TV service operator appear on the screen This menu option is available only if the CAM is inserted and activated correctly Use Philips EasyLink Your TV supports Philips EasyLink which enables one touch play and one touch standby between EasyLink compliant devices Note Compliant devices must be connected to your TV via HDMI Enable or disable EasyLink Do not enable Philips EasyLink if you do not intend to use it 1 Press MENU 2 Press AY 4b to select Setup gt Installation gt Preferences gt EasyLink J select On or Off Use one touch play 1 After enabling EasyLink press play on your device L gt The V automatically switches to the correct source Use one touch standby 1 Press and hold OStandby on
10. menu screen care software standby switch channels switch off switch on troubleshooting tuner technical specifications wall mount TV lock lock channels lock connected devices V Video format video format technical specifications volume adjust 24 Information about how to re tune your TV during the TV switchover Keep this user manual safe you ll need it pm Television in the UK is going digital bringing us all more choice and new services Starting in late 2007 and ending in 2012 television services in the UK will go completely digital TV region by TV region Please see the next page to find out when your area switches to digital Digital UK is the independent non profit organisation leading the process of digital TV switchover in the UK Digital UK provides im partial information on what people need to do to prepare for the move to digital and when they need to do it How the switchover affects your TV equipment Your new TV has a digital tuner built in which means it is ready to receive the Freeview signal by simply plugging it into your aerial socket check if you can get digital TV through your aerial now or whether you ll have to wait until switchover at www digitaluk co uk When the TV switchover happens in your area there are at least two occasions when you will need to re tune your TV in order to continue receiving your existing TV channels and also to pick up new ones
11. pre defined settings or change settings manually Use settings assistant Use the settings assistant to guide you through the best picture and sound settings 1 Press amp MENU 2 Press Av to select Setup gt Picture 7 Settings assistant 3 Press OK L gt The Settings assistant menu appears Follow the on screen instructions to choose your preferred picture settings Use smart picture Use smart picture to apply pre defined picture settings 1 Press O PICTURE t gt The Smart picture menu appears 2 Press AY to select one of the following smart picture settings Personal Lists customised personal picture settings e Vivid Maximises picture settings Standard Adjusts picture settings to suit most environments and types of video e Movie A pplies picture settings ideally suited for movie viewing Game Applies picture settings maximised for fast moving games e Energy saving Applies low energy picture settings J Press OK to confirm your choice L gt he selected smart picture setting is applied Manually adjust picture settings 1 Press amp MENU 2 Press Av to select Setup gt Picture Settings assist Action Smart picture Personal Contrast Hn ii nni Colour HN G GG nnn ii HN E GG G Noise reduction Off Brightness p Features Installation Hue Sharpness Software update 3 Press AYP to select one of the following picture settings e Sma
12. the TV s or device s remote control for at least three seconds Ls The TV and all connected HDMI devices switch to standby Use a Kensington lock There is a Kensington security slot at the back of the TV Prevent theft by looping a Kensington ock between the slot and a permanent object such as a heavy table Ae EN 33 English 8 Product information Product information is subject to change without notice For detailed product Information go to www philips com support Supported display resolutions Computer formats e Resolution refresh rate 640 x 480 60Hz e 800 x 600 60Hz e 1024 x 768 60Hz 1280 x 1024 60 Hz e 1360 x 768 60Hz e 1440 x 900 60Hz For Full HD only e 1680 x 1050 50Hz 60Hz For Full HD only Via HDMI DVI input Video formats e Resolution refresh rate e 480i 60Hz 480p 60Hz e 576i 50Hz e 576p 50Hz e 720p 50Hz 60Hz e 1080 50Hz 60Hz e 1080p 24Hz 25Hz 30Hz 50Hz 60Hz Multimedia e Supported storage device USB Only FAT or FAT 32 USB storage devices are supported Supported multimedia file formats Images JPEG Audio MP3 Multimedia file names must not exceed 128 characters 34 EN Tuner Reception Transmission Aerial input 5ohm coaxial IEC75 e DVB DVB Terrestrial DVB T MPEG4 only in some models V system DVB COFDM 2K 8K PAL B G D K SECAM B G D K L L Vid
13. to exit the teletext options menu EN 13 English Select teletext subpages A teletext page can hold several subpages Subpages are displayed on a bar next to the main page number 1 Press MHEG TELETEXT L gt The teletext screen appears 2 Press AV to select a teletext page 3 Press lt gt to enter a subpage Select T O P teletext broadcasts Table Of Pages T O P teletext broadcasts allow you to jump from one subject to another without using page numbers T O P teletext is not broadcast on all TV channels 1 Press MHEG TELETEXT L gt The teletext screen appears 2 Press INFO L gt The T O P overview appears Press amp lt 4P to select a subject 3 4 Press OK to view the page Create and use lists of favourite channels You can create lists of your preferred TV channels and radio stations so that you can find those channels easily Ea You can create and store up to four favourite lists on your TV Select a favourite list 1 When watching TV press OK to display the channel grid 2 Press OPTIONS L gt The channel options menu appears 3 Press AV to select Show fav ch and press OK L gt The favourite lists appear 4 Press AY to select a favourite list and press OK L gt Only channels in the favourite list appear in the channel grid The favourite channel grid is empty until you add channels into the favourite lists View all channels You
14. 9 pro Minute KArjon xwpic xpewon Ingyenes hivas free 0 08 Al minuto local local local Ortsgesprach Appel local 0 10 Per minuut Lokalsamtale potaczenie lokalne Chamada local Apel local MecTHbl 3BOHOK Lokalni poziv Bezplatny hovor lokalni klic 0 10 Por minuto Lokalsamtal Appel local Ortsgespr ch Chiamata locale Sehirici arama local MicueBn BAKAMK This information is correct at the time of press For updated information see www philips com support Contents 1 Notice 2 2 Important 4 3 TV overview 6 Side controls and indicators 6 Remote control 6 4 Use your product 8 Switch your TV on off or to standby 8 Switch channels 8 Watch connected devices 2 Adjust TV volume 9 Use teletext 9 5 Use more of your product 10 Access TV menus 10 Remove devices from the home menu 10 Change picture and sound settings 10 Use advanced teletext features 13 Create and use lists of favourite channels 14 Use the Electronic Programme Guide 15 Use timers 16 Use TV lock and parental ratings 16 Use subtitles 18 Use the TV clock 19 View photos and play music from a USB storage device 12 Listen to digital radio channels 21 Update the TV software 21 Change TV preferences 22 Access decoder channel 22 Start aTV demo 22 Reset the V to factory settings 23 6 Install channels 24 Automatically install channels 24 Manually install channels 25 Rename channels 26 Reorder channels 26 Test digital reception 26
15. HDMI or YPbPr Change picture format 1 Press FORMAT L gt A picture format bar appears 2 Press Av or B FORMAT to select a picture format L gt The selected picture format is activated 3 Press OK to confirm your choice EN 11 English Summary of picture formats The following picture settings can be configured Note Depending on the format of the picture source some picture settings are not available Auto format Not for PC mode Enlarges the picture automatically to best fit the screen The subtitles remain visible Super zoom Not for HD and PC mode Removes the black bars on the side of 4 3 broadcasts There is minimal distortion 4 3 Shows the classic 4 3 format Subtitle zoom Displays 4 3 pictures over the full area of the screen with sub titles visible Part of the top of the picture is clipped off Movie expand 14 9 Not for HD and PC mode Scales 4 3 format to 14 9 Movie expand 16 9 Not for HD and PC mode Scales 4 3 format to 16 9 Wide screen Stretches the classic 4 3 format to 16 9 12 EN Unscaled For HD and PC mode only and in selected models only Allows maximum sharpness Some distortion may be present due to the broadcaster s systems Set your PC resolution to wide screen mode for best results Use smart sound Use smart sound to apply pre defined sound settings 1 Press SOUND t gt The Smart sound menu appea
16. Register your product and get support at www philips com welcome PHILIPS EN User Manual 19PFL3404H 12 22PFL3404H 12 26PFL3404H 12 32PFL3404H 12 42PFL3604H 12 19PFL3404D 12 22PFL3404D 12 26PFL3404D 12 32PFL3404D 12 42PFL3604D 12 19PFL3404D 05 22PFL3404D 05 26PFL3404D 05 PHILIPS Osterreich Belgi Belgique Bbarapua Hrvatska Cesk republika Danmark Estonia Suomi France Deutschland E Aa a Magyarorsz g Ireland Italia Ka3akCTaH Latvia Lithuania Luxemburg Luxembourg Nederland Norge Polska Portugal Romania Poccua Cp6nja Slovensko Slovenija Espana Sverige Suisse Schweiz Svizzera Turkiye United Kingdom YxpaiHa 0810 000205 078250145 3592 489 99 96 01 6403 776 800142840 3525 8759 6008600 09 2311 3415 0821 611655 01803 386 852 0 0800 3122 1280 0680018189 North 0800 055 6882 South 1800 PHILIPS 7445477 840320086 7 727 250 66 17 67228896 52737691 40 6661 5644 0900 8407 2270 8111 022 3491504 800 780 903 031 810 71 25 0800 89 49 10 Moscow 495 961 1111 Outside Moscow 8 800 200 0880 381 114 440 841 0800 004537 00386 12 80 95 00 902 888 784 08 5792 9100 0844 800 544 0800 261 3302 General No 0870 900 9070 General National Rate No 0870 911 0036 8 800 500 69 70 0 07 pro Minute 0 06 Per minuut Par minute MecteH pasroBop Lokalni poziv Bezplatny hovor Lokalt opkald local paikallispuhelu 0 09 Par minute 0 0
17. TELEVISION QO OG YO C9 309 OD Standby On Switches the TV to standby if it is on Switches on the TV if it is in standby 2 amp MENU Toggles the main menu on or off MHEG TELETEXT Toggles teletext on or off SOURCE Selects connected devices Colour buttons Selects tasks or options AD Audio Descriptor For RF Digital TV only UK only Enables audio commentary for the visually handicapped 7 amp OPTIONS Accesses options relating to the current activity or selection 8 OK Confirms an entry or selection and displays the channel grid when watching TV 9 AY 4b Navigation buttons Navigates through the menus INFO Displays program information when available If the information spans multiple pages press OPTIONS to go to the next page x Mute Mutes or restores audio output 2 P Programme Switches to the next or previous channel When the TV menu is on this functions as Page Up Down 0 9 Numeric buttons Selects a channel or setting O PICTURE Smart picture Launches the picture menu 45 2 SOUND Smart Sound Launches the sound menu lt Volume Increases or decreases volume 17 BACK P P Previous channel e Returns to a previous screen e Returns to the previously viewed channel GUIDE Switches between channel grid and programme list SUBTITLE For RF Digital TV only
18. Use the channel grid When you use a favourite list you can only select those channels in the list Watch connected devices Switch on the device before selecting it as a source on the TV Use the source button MENU FORMAT INCR SURR MHEG 7 GJ wed pea DEMO SUBTITLE UD sm amp 1 Press SOURCE L gt The source list appears 2 Press the Navigation buttons to select a device 3 Press OK to confirm your choice L gt The TV switches to the selected device Adjust TV volume os reg 1 1 1 1 i 5 VOLUME 1 1 1 O SOURCE To increase or decrease volume Press Press VOLUME on the side of the TV To mute or unmute sound Press K to mute the sound Press K again to restore the sound Use teletext MENU FORMAT INCR SURR BE S E pog Gong DEMO SCENEA SUBTITLE AD 1 Press MHEG TELETEXT L gt The main index page appears 2 Selecta page as follows Press the Numeric buttons to enter a page number Press P or AY to view the next or previous page Press the Colour buttons to select a colour coded item Press D BACK to return to a previously viewed page Press MHEG TELETEXT to exit teletext For UK users only Some digital T V channels offer dedicated digital text services for examp
19. ack connector for 26 inch TV and larger EXT1 EXT2 RGB CVBS CVBS 750 ar TV ANTENNA 4 HDMI 1 HDMI and AUDIO IN Digital audio and video input from high definition digital devices such as Blu ray players Audio input from devices that require a separate audio connection such as a computer Connections via DVI or VGA require an additional audio cable see Connect a computer on page 31 Q EXT 3 Y Pb Pr and AUDIO L R Analogue audio and video input from analogue or digital devices such as DVD players or game consoles 3 EXT 1 RGB and CVBS EXT 2 CVBS Analogue audio and video input from analogue or digital devices such as DVD players or game consoles EXT 2 supports S Video EXTI EXT2 RGB CVBS CVBS DVD OO OO LJ m m m LJ m m OOOO LLLLLLLLILD EN 29 English 4 TV ANTENNA 1 COMMON INTERFACE Signal input from an antenna cable or Slot for a Conditional Access Module satellite CAM 750 r TV ANTENNA E 4 2 AUDIO L R Audio input from analogue devices connected to VIDEO S SPDIF OUT AG VHS Digital audio output to home theatres and other digital audio systems 3 VIDEO Composite video input from analogue 6 SERV U devices such as VCRs For software update Side connector 4 USB Data in
20. ail and file browsing views View photos 1 In the USB thumbnail browser select Picture and press P to enter Press I GUIDE to switch between thumbnail and file browsing views 2 3 Press Av to select a photo or a photo album 4 Press OK to view the selected photo in full screen mode Tip When in full screen mode press 4 gt to move between photos View a slide show of your photos 1 When a full screen image of a photo is displayed press OK L gt A slide show begins from the selected image 20 EN 2 Press OK to pause the slide show L gt heM icon appears Press lt P to go back or move forward to the next image e BACK to stop the slide show Change slide show settings 1 when viewing a slide show press amp OPTIONS L gt The slide show options menu appears 2 Press AV to select one of the following e Start Stop slide Starts or stops a slide show e Slideshow trans Sets the transition from one picture to the next e Slideshow freq Sets the amount of time that a picture is shown Rotate image Rotates a picture Show info Displays the picture name date size and next picture in the slide show J Press OK to confirm your setting Note Rotate image and Show info appear only when you press OK or PII to pause the slideshow Listen to music 1 In the USB thumbnail browser view select Music and press P to enter Press
21. annel grid appears D Press AV to select a channel that you wish to remove from the list 6 Press OPTIONS 7 Press AV to select Unmark as fav and press OK L gt The channel is removed from the favourite list Use the Electronic Programme Guide EPG is an on screen guide available for digital channels EPG allows you to View a list of digital programmes being broadcast View upcoming programmes Group programmes by genre Set reminders when programmes start e Set up preferred EPG channels Switch on EPG 1 When watching TV press GUIDE L gt The EPG planner screen appears displaying information about the scheduled programmes EPG data is available only in selected countries and can take some time to load Tip Press GUIDE to switch between EPG and channel grid Use EPG 1 when watching T V press GUIDE L gt The EPG planner screen appears 2 Press amp MENU L gt The program guide menu appears 3 Press AY 4b to select an option and then press OK to confirm it Press MENU to exit the EPG menu Note Only the channels marked with x in the Pref EPG channel list appear in the EPG menu EN 15 English Use the EPG options menu Use the EPG options menu to set or clear reminders change day and access other useful EPG options 1 Press GUIDE 2 Press OPTIONS L gt The EPG menu appears 3 Press AV to select
22. applicable to TVs supporting MPEG4 HD standard All other registered and unregistered trademarks are the property of their respective owners EN English Important Read and understand all Instructions before you use your TV If damage is caused by failure to follow instructions the warranty does not apply Safety Risk of electric shock or fire Never expose the TV to rain or water Never place liquid containers such as vases near the TV If liquids are spilt on or into the TV disconnect the TV from the power outlet immediately Contact Philips Consumer Care to have the TV checked before use Never place the TV remote control or batteries near naked flames or other heat sources including direct sunlight To prevent the spread of fire keep candles or other flames away from the TV remote control and batteries at all times Never insert objects into the ventilation slots or other openings on the TV When the V is swivelled ensure that no strain is exerted on the power cord Strain on the power cord can loosen connections and cause arcing Risk of short circuit or fire Never expose the remote control or batteries to rain water or excessive heat EN Avoid force coming onto power plugs Loose power plugs can cause arcing or fire Risk of injury or damage to the TV Two people are required to lift and carry a TV that weighs more than 25 kg When stand mounting the TV us
23. atically Programme no Selects the channel 4 Press amp MENU to exit El Select On timer gt Activate gt Off to disable On timer Use TV lock and parental ratings You can prevent your children from watching certain programmes or certain channels by locking the TV controls and by using ratings Set or change code Press ft MENU Press AV to select Setup gt Features gt Set code Press OK or P to enter the code setup Enter your code using the Numeric buttons U AW N Re enter the same code in the new dialogue box for confirmation L gt f the code is set successfully the dialogue box will disappear However if the code cannot be set a new dialogue box will prompt you to re enter the code 6 If you want to change the code select Setup gt Features gt Change code 7 Enter your current code using the Numeric buttons L gt Ifthe code is validated a new dialogue box will prompt you to enter your new code 8 Enter the new code using the Numeric buttons L A message appears prompting you to enter the new code again for confirmation Tip f you forget your code enter 8888 to override any existing codes Lock or unlock the TV Locking the TV prevents your child from accessing all channels and connected devices 1 Press amp MENU 2 Press Av to select Setup gt Features gt TV lock L A screen appears prompting yo
24. cribes how to connect various devices with different connectors and supplements examples provided in the Quick Start Different types of connectors may be used to connect a device to your TV depending on availability and your needs Back connector for 19 22 inch TV EXT RGB CVBS 750 W TV ANTENNA 009 1 PC IN VGA and AUDIO IN Audio and video input from a computer PC IN AUDIO O EXT 2 Y Pb Pr and AUDIO L R Analogue audio and video input from analogue or digital devices such as DYD players or game consoles EN 27 English 3 EXT 1 CVBS and RGB Analogue audio and video input from analogue or digital devices such as DVD players or game consoles EXT I RGB CVBS zm mu mu mm C mu TL m mm 4 TV ANTENNA Signal input from an antenna cable or satellite 750 mE TV ANTENNA AV OUT VIDEO OUT and AUDIO OUT L R Audio and video output to analogue devices such as another TV or a recording device 28 EN 6 SPDIF OUT Digital audio output to home theatres and other digital audio systems SPDIF OUT 7 HDMI 1 Digital audio and video input from high definition digital devices such as Blu ray players Connections via DVI or VGA require an additional audio cable see Connect a computer on page 31 SERV U For software update B
25. ct Automatic or Manual Press OK to confirm U UC N Change the time zone Press amp MENU Press AY 4b to select Setup gt NA Installation gt Clock gt Time zone UJ Press AY to select your time zone Press OK to confirm Note This option is only available if you select Auto clock gt Manual In countries with clock transmission data Use daylight saving Press amp MENU 1 2 Press Av to select Setup gt Installation gt Clock gt Daylight saving Press AY to select Standard time or Daylight saving time UI AW Press OK to enable your selection Note Press OK or P to enter Daylight saving clock gt Manual This option is only available if you select Auto View photos and play music from a USB storage device Caution Philips is not responsible if the USB storage device Is not supported nor is it responsible for damage or loss of data from the device Your TV is fitted with a USB connector that enables you to view photos or listen to music stored on a USB storage device EN 19 English 1 Turn on the TV 2 Connect the USB device to the USB port on the side of your TV L gt The home menu appears f lt new devi Press AV to select Browse USB Press OK to confirm L gt The USB thumbnail browser appears A Lw Tip e Press GUIDE to switch between thumbn
26. d market products that cause no adverse health effects Philips confirms that if its products are handled properly for their intended use they are safe to use according to scientific evidence available today Philips plays an active role in the development of international EMF and safety standards enabling Philips to anticipate further developments in standardisation for early integration in its products Mains fuse UK only This TV is fitted with an approved moulded plug Should it become necessary to replace the mains fuse this must be replaced with a fuse of the same value as indicated on the plug example 10A Remove fuse cover and fuse The replacement fuse must comply with BS 1362 and have the ASTA approval mark If the fuse is lost contact your dealer in order to verify the correct type 3 Refit the fuse cover In order to maintain conformity to the EMC directive the mains plug on this product must not be detached from the mains cord cable Copyright VESA FDMI and the VESA Mounting Compliant logo are trademarks of the Video Electronics Standards Association Kensington and Micro Saver are registered US trademarks of ACCO World Corporation with issued registrations and pending applications in other countries throughout the world Q DOLBY DIGITAL PLUS Manufactured under licence from Dolby Laboratories Dolby and the double D symbol are trademarks of Dolby Laboratories Note Only
27. e only the supplied stand Secure the stand to the TV tightly Place the TV ona flat level surface that can support the combined weight of the TV and the stand When wall mounting the TV use only a wall mount that can support the weight of the TV Secure the wall mount to a wall that can support the combined weight of the TV and wall mount Koninklijke Philips Electronics N V bears no responsibility for improper wall mounting that result in accident injury or damage Risk of injury to children Follow these precautions to prevent the TV from toppling over and causing injury to children Never place the TV on a surface covered by a cloth or other material that can be pulled away Ensure that no part of the TV hangs over the edge of the surface Never place the TV on tall furniture such as a bookcase without anchoring both the furniture and TV to the wall or a suitable support e Educate children about the dangers of climbing on furniture to reach the TV Risk of overheating Never install the TV in a confined space Always leave a space of at least 4 inches or 10 cm around the TV for ventilation Ensure curtains or other objects never cover the ventilation slots on the T V Risk of damage to the TV Before you connect the TV to the power outlet ensure that the power voltage matches the value printed on the back of the TV Never connect the TV to the power outlet if the voltage is different Ris
28. eo playback NTSC SECAM PAL uner Bands Hyperband S channel UHF VHF Remote control Type PFO1E09B Batteries 2 x AAA LRO3 type Power Mains power 220 240V 50Hz Standby power lt 0 3W e Ambient temperature 5 to 40 degrees Celsius Supported TV mounts To mount the TV purchase a Philips TV mount or a VESA compatible TV mount To prevent damage to cables and connectors be sure to leave a clearance of at least 2 2 inches or 5 5cm from the back of the TV VN Warning Follow all instructions provided with the TV mount Koninklijke Philips Electronics N V bears no responsibility for improper TV mounting that results in accident injury or damage TV screen Required Required size inches pitch mm mounting bolts 19 100 x 100 4 x M4 22 100 x 100 4 x M4 26 100 x 200 6 x M4 32 200 x 200 4 x M6 42 400x400 4xM6 9 Troubleshooting This section describes commonly encountered Issues and accompanying solutions General TV issues The TV does not switch on Disconnect the power cable from the power outlet Wait for one minute then reconnect it e Check that the power cable is securely connected The remote control is not working properly e Check that the remote control batteries are correctly inserted according to the orientation e Replace the remote control batteries if they are flat or weak e Clean the remote control and TV sensor lens The s
29. ess Av to select Setup gt Installation gt Channel install gt Channel assistant 24 EN Menu language Channel assistant Preferences Location Picture Language Sound Decoder Channel Features Installation Software update Clock Auto clock Factory settings Action 3 Press OK or P to enter the menu L gt The country menu appears Select your country then press OK Slovakia Slovenia Spain Sweden Switzerland Turkey Ukraine 4 Press AY to select your country D Press OK to confirm your choice L gt The channel installation guide appears on the screen Step 3 Install channels Install the available analogue and digital TV channels and digital radio channels automatically 1 From the channel installation guide screen see Step 2 Select your country on page 24 select Full installation to automatically install all TV channels and digital radio channels Start automatic installation This takes a few minutes Full installation 2 Press OK to confirm Ls The TV starts to search and store all the available channels System searching Please wait Digital channels found Analogue channels found 3 When installation is complete press OK to return to Installation menu Step 4 Update the channel list You can choose to enable auto update of channels if your TV is in standby mode If you enable this feature the channels stored
30. ess OK to search for the next available channel 6 Press 9 BACK when the new channel is found 7 Press AV to select Store new channel to store the new channel under a new channel number 8 Press OK or gt to enter Store new channel and press OK 9 Press 4 to return to the Analogue Manual menu EN 25 English Step 3 Fine tune analogue channels 1 Press amp MENU 2 Press AYP to select Setup gt Installation gt Channel install gt Analogue Manual The Analogue Manual menu appears Press AY to select Fine tune and then OK or P to enter Fine tune Press AV to adjust frequency Press OK when done OUA W Press AV to select Store current channel to store the fine tuned channel under the current channel number N Press OK or P to enter Store curr chan and press OK 8 Press lt o return to the Channel install menu Rename channels Channels can be renamed so that a name of your choice appears whenever the channel is selected 1 When watching TV press OK to display the channel grid Press AV to select the channel you want to rename 2 3 Press OPTIONS L gt The channel options menu appears 4 Press AY to select Rename channel L gt A text input box appears g Press AV to select and change characters 6 Select Done to finish renaming channels Tip Use Aa to change upper case letter to lower case letter and vice versa
31. ew it 3 Press DEMO to exit Reset the TV to factory settings You can restore the default picture and sound settings of your TV Channel installation settings remain the same 1 Press MENU 2 Press Av to select Setup gt Installation gt Factory settings 3 Press OK or to enter the Factory settings menu L A factory setting message appears 4 select Reset to start resetting Press amp MENU to exit EN 23 English 6 Install channels The first time you set up your TV you are prompted to select a menu language and to install TV and digital radio channels if available This chapter provides instructions on how to re install and fine tune channels Automatically install channels This section describes how to search and store channels automatically Step 1 Select your menu language 1 Press amp MENU 2 Press Av to select Setup gt Installation gt Language gt Menu language 3 Press OK or to enter Menu language Menu language Primary audio language Picture Channel install Preferences Secondary audio language Menu language A English v Installation Factory settings Software update Hearing impaired 4 Press AY to select a language setting B Press OK to confirm 6 Press lt to return to Installation menu Step 2 Select your country Select your country for proper channel installation 1 Press amp MENU 2 Pr
32. for a TV to display content from a HDMI device e Ifthe TV does not recognize the HDMI device and no picture is displayed try switching the source from one device to another and back again If there are intermittent sound disruptions check that output settings from the HDMI device are correct 36 EN Ifa HDMI to DVI adaptor or HDMI to DVI cable is used check that an additional audio cable is connected to AUDIO L R or AUDIO IN mini jack only Computer connection issues The computer display on the TV is not stable e Check that a supported resolution and refresh rate is selected on the computer Set the TV picture format to unscaled Contact us If you cannot resolve your problem refer to the FAQs for this product at www philips com support If the problem remains unresolved contact Philips Consumer Care in your country as listed in the Addendum Warning Do not attempt to repair the product yourself This may cause severe injury irreparable damage to your product or void your warranty Make a note of your TV model and serial number before you contact Philips These numbers are printed on the back of the TV and on the packaging 10 Index B batteries bracket C Channel list favourite troubleshooting update channels favourite list Install automatic manual rename test reception child lock ratings lock clock computer format technical specifications C
33. he TV and accessories only as intended by the manufacturer The caution sign printed on the back of the TV indicates risk of electric shock Never remove the TV cover Always contact Philips Customer Support for service or repairs LA AL CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR PRECAUCION ADVERTENCIA NO ABRIR RIESGO DE CHOQUE ELECTRICO Any operation expressly prohibited in this manual or any adjustments and assembly procedures not recommended or authorised in this manual shall void the warranty Pixel characteristics This LCD product has a high number of colour pixels Although it has effective pixels of 99 999 or more black dots or 2 EN bright points of light red green or blue may appear constantly on the screen This is a structural property of the display within common industry standards and Is not a malfunction Compliance with EMF Koninklijke Philips Electronics N V manufactures and sells many products targeted at consumers which like any electronic apparatus in general have the ability to emit and receive electromagnetic signals One of Philips leading Business Principles Is to take all necessary health and safety measures for our products to comply with all applicable legal requirements and to stay well within the EMF standards applicable at the time of producing the products Philips is committed to develop produce an
34. in your TV will be updated every morning according to the channel information in the broadcast 1 Press amp MENU 2 Press Av to select Setup gt Installation gt Channel install gt Standby update 3 Select On to enable the automatic update or select Off to disable it Manually install channels This section describes how to search and store analogue TV channels manually Step 1 Select your system Skip this step if your system settings are correct 1 Press MENU 2 Press AYP to select Setup gt Installation gt Channel install gt Analogue Manual The Analogue Manual menu appears Picture Language Channel assistant Standby update A System Y Analogue Manual Analogue Manual Clock Factory settings Installation 5 Software update Press OK or P to enter System menu Press AY to select your country or region Press OK to confirm OU AW Press 4 to return to Channel install menu Step 2 Search and store new TV channels 1 Press amp MENU 2 Press Av to select Setup gt Installation gt Channel install gt Analogue Manual The Analogue Manual menu appears 3 Press AV to select Search and then OK or p to enter Search 4 Press Av to manually enter the three digit frequency 5 Press OK to begin search L If a channel is unavailable at the selected frequency pr
35. k of injury fire or power cord damage Never place the TV or any objects on the power cord To easily disconnect the TV power cord from the power outlet ensure that you have full access to the power cord at all times When you disconnect the power cord always pull the plug never the cable Disconnect the TV from the power outlet and aerial before lightning storms During lightning storms never touch any part of the TV power cord or aerial cable Risk of hearing damage Avoid using earphones or headphones at high volumes or for prolonged periods of time Ifthe TV is transported in temperatures below 5 C unpack the TV and wait until the TV temperature matches room temperature before connecting the TV to the power outlet Screen care e Avoid stationary images as much as possible Stationary images are images that remain on screen for extended periods of time Examples include on screen menus black bars and time displays If you must use stationary images reduce screen contrast and brightness to avoid screen damage Unplug the TV before cleaning Clean the TV and frame with a soft damp cloth Never use substances such asalcohol chemicals or household cleaners on the TV Risk of damage to the TV screen Never touch push rub or strike the screen with any object e To avoid deformations and colour fading wipe off water drops as soon as possible Disposal of your old product and batteries
36. le BBC1 DEMO SUBTITLE AD and BACK buttons on the remote control do not work when you are watching a channel with MHEG service This limitation affects these models only 19PFL3404D 05 22PFL3404D 05 and 26PFL3404D 05 EN 9 English 5 Use more of your product Access TV menus Menus help you to install channels change picture and sound settings and access other features 1 Press amp MENU L gt The menu screen appears Add new device 2 Press the AY to select and navigate through one of the following menus e Watch TV Switches back to the aerial source if another source Is selected Setup Accesses menus that allow you to change picture sound and other TV settings e Add new device Adds new devices to the home menu 3 Press OK to confirm your choice 4 Press amp MENU to exit Ea After selecting Add new device follow the on screen instructions to select the correct device and connector 10 EN Remove devices from the home menu If a device is no longer connected to the TV remove it from the home menu 1 Press MENU 2 Press AV to select a device to remove 3 Press OPTIONS The Remove device list appears 4 Press OK and select Remove to remove the device L gt The selected device is removed from the home menu Change picture and sound settings Change picture and sound settings to suit your preferences You can apply
37. le try to improve the reception quality by changing the antenna direction or moving devices away from the TV If reception on only one channel is poor fine tune this channel There is poor picture quality from connected devices e Check that the devices are connected properly e Check that the picture settings are correctly set The TV did not save your picture settings e Check that the TV location is set to the home setting This mode offers you the flexibility to change and save settings EN 35 English The picture does not fit the screen it is too big or too small e Try using a different picture format The picture position is incorrect Picture signals from some devices may not fit the screen correctly Check the signal output of the device Sound issues There is a picture but sound quality is poor Note f no audio signal is detected the TV automatically switches the audio output off this does not indicate malfunction e Check that all cables are properly connected e Check that the volume is not set to 0 e Check that the sound is not muted There is a picture but the sound quality is poor e Check that the sound settings are correctly set There is a picture but sound comes from one speaker only e Verify that sound balance is set to the centre HDMI connection issues There are problems with HDMI devices Note that HDCP support can delay the time taken
38. ls are skipped If you access the locked channels from the channel grid a screen prompting you to enter your current code appears Set parental ratings Some digital broadcasters rate their programmes according to age You can set your TV to display only programmes with age ratings higher than your child s age 1 Press amp MENU 2 Press Av to select Setup gt Features gt Parental rating L gt A code setup screen appears Enter your code using Numeric buttons L gt The parental rating menu appears Press AY to select an age rating Press OK to confirm Press MENU to exit ON Un UJ Use subtitles You can enable subtitles for each TV channel Subtitles are broadcast via teletext or DVB T digital broadcasts With digital broadcasts you have the additional option of selecting a preferred subtitle language Enable subtitles on analogue TV channels 1 Select an analogue TV channel 2 Press MHEG TELETEXT 18 EN Enter the three digit page number of the subtitle page with the Numeric buttons Press MHEG TELETEXT to switch off teletext Press SUBTITLE L gt The Subtitle mode menu appears Ow G A C Select On to display subtitles always or On during mute to display subtitles only when audio is muted 7 Press OK to enable subtitles Repeat this procedure to enable subtitles on each analogue channel El Select Subtitle mode gt Off to disable s
39. n Optimises TV settings for your location home or shop Volume bar Displays the volume bar when adjusting the volume Channel info Displays information about the TV channel every time you switch channels Select Full to view channel information or Off to turn off the channel information EasyLink Enables one touch play and one touch standby between EasyLink compliant devices E sticker For shop mode only Sets the location of the e sticker 22 EN Access decoder channel You can map channels provided through a decoder or descrambler to your TV channel selection In this way you can select these channels by using the RC of your TV The decoder or a descrambler must be connected to EXT1 SCART Set decoder channel Map channels from a decoder or descrambler 1 Press MENU 2 Press Av to select Setup gt Installation gt Preferences gt Decoder 3 Press OK or to enter Decoder menu 4 Press a to select Channel and press OK or P to enter L gt A list of analogue channels appears on the screen D Press AV to select one channel to map to the decoder descrambler channel and press OK to confirm 6 Select Status and press OK or P to enter 7 Press AV to select EXT 1 SCART the connector used by the decoder descrambler 8 Press OK 9 Press amp MENU to exit Start a TV demo 1 Press DEMO on the remote control 2 Press AV to select a demo and press OK to vi
40. oftware information Update software digital broadcasts You can update the TV software via a USB device or OAD Update using a USB device Connect your USB device to the USB port at the side of your TV 1 ifthe software update screen does not appear automatically select Setup gt Software update gt Local updates gt USB to update the TV software manually 2 Follow the on screen instructions to complete the update The TV restarts after the software update is complete Update using OAD On the Air software Download 1 f using DVB T digital broadcast your TV automatically receives software updates If you receive a message on your screen asking you to update your software EN 21 English Select Update now to update the software immediately Select Remind me later to exit the update screen at that time and be reminded later Select Cancel to skip the update 2 If you select Cancel you can manually access the OAD update by selecting Setup gt Software update gt Local updates gt OAD Select the available version of OAD and press OK W 4 Follow the on screen instructions to start the update The TV restarts after the software update is complete Change TV preferences Press ft MENU Press AY 4b to select Setup gt Installation gt Preferences WU ON a Press OK or P to enter Preferences Locatio
41. onditional Access Module connections HDMI troubleshooting mains cord technical specifications troubleshooting D demo devices watch digital channel test reception digital radio digital services CAM teletext 34 34 14 35 14 24 25 26 26 18 19 34 32 36 27 34 36 22 26 21 32 display resolution E EasyLink disable enable one touch play one touch standby environmental care F factory settings favourite list select set up H HDMI cable troubleshooting install channels automatic manual K Kensington lock L location lock Kensington M menu main menu teletext Multimedia technical specifications multimedia listen to music view photos EN 34 32 32 33 23 14 14 36 24 25 33 22 33 10 13 34 20 20 37 English music digital radio 21 USB 20 O One touch play 32 One touch standby 33 P picture format picture format change 1 troubleshooting 35 Picture settings 10 R ratings 18 reception 35 remote control overview 6 technical specifications 34 S settings assistant 10 sleep timer 16 Smart card 32 Smart settings 10 12 software version 21 sound settings 12 subtitles language 18 on analogue channel 18 on digital channel 18 T Table of Pages 14 technical specifcations 34 Teletext features 13 subpages 14 table of pages 14 timer on timer 16 standby 16 38 EN troubleshooting TV adjust volume
42. one of the following options e Set remind Clear remind Change day e Show info Search by genre Schedule reminders Pref EPG channel 4 Press OK to enter or activate the option D Press D BACK to exit the EPG menu Tip Press il GUIDE to switch between EPG and channel grid Use timers You can set timers to switch the V on or switch to standby at a specified time Automatically switch the TV to standby sleeptimer Sleeptimer switches the TV to standby after a pre defined period of time Tip You can always switch off your TV earlier or reset the sleeptimer during the countdown Press ft MENU Press AY b to select Setup gt Features gt Sleep timer L gt The bar appears NA J Press lt P to set the sleep time L gt The sleeptimer can be up to 180 minutes in steps of five minutes If set to zero minutes the sleeptimer is switched off 4 Press OK to activate the sleeptimer L gt The TV switches to standby after the pre defined period of time Automatically switch the TV on on timer You can switch the TV to a specified channel at a specified time from standby or power on mode 1 Press amp MENU 2 Press Av to select Setup gt Features gt On timer 3 Press OK or to enter the On timer menu e Activate Selects the frequency to Off or Once or Daily Time Sets the starting time to switch on the TV autom
43. put from USB storage devices USB iS 30 EN HDMI Only for TVs 26 inches and larger Digital audio and video input from high definition digital devices such as Blu ray players e DVI HDMI cable e Blu ray Disc Connect a computer Before you connect a computer to the TV e Set the screen refresh rate on your computer to 60Hz e Select a supported screen resolution on your computer Connect a computer with one of the following connectors Note Connections via DVI or VGA require an additional audio cable HDMI cable For TV of size 19 22 inch PC IN AUDIO For TV of size 26 inch and larger AUDIO IN LEFT RIGHT HDMI I DVI HDMI cable and HDMI DVI adaptor For TV of size 19 22 inch PC IN AUDIO For TV of size 26 inch and larger AUDIO IN LEFT RIGHT HDMI I DVI e VGA cable For TV of size 19 22 inch only PC IN AUDIO EN 31 English Use a Conditional Access Module A Conditional Access Module CAM is provided by digital TV service operators to decode digital TV channels Note f required refer to documentation from your operator on how to insert a smart card into the Conditional Access Module Insert and activate a CAM Caution Be sure to follow the instructions described below Wrong insertion of a CAM may
44. rs 2 Press Av to select one of the following smart sound settings Standard Adjusts sound settings to suit most environments and types of audio News Applies sound settings ideally suited for spoken audio such as the news Movie Applies sound settings ideally suited for movies Personal Applies the settings that were customised in the sound menu J Press OK to confirm your choice L gt The selected smart sound setting is applied Adjust sound settings 1 Press amp MENU 2 Press AY 4b to select Setup gt Sound L gt The Sound menu appears Picture I Features Installation Smart sound Bass Treble Volume Vol vis impaired Balance Audio language Standard English 3 Software update Dual I II Dual Press AY4b to select one of the following sound settings Smart sound Accesses pre defined smart sound settings Bass Adjusts the bass level Treble Adjusts the treble level Volume Adjusts the volume Vol vis impaired Sets the mix of visually impaired audio with regular audio When available visually impaired audio includes audio descriptions of on screen action You can also enable this by pressing AD Audio Descriptor Balance Adjusts the balance of the right and left speakers to best suit your listening position Audio language Available for digital channels when multiple languages are broadcast Lists available audio languages
45. rt picture Accesses pre defined smart picture settings Contrast Adjusts the intensity of bright areas keeping dark areas unchanged Brightness Agjusts the intensity and details of dark areas Colour Adjusts colour saturation e Hue Compensates colour variations in NTSC encoded transmissions Sharpness Adjusts the level of sharpness in image details e Noise reduction Filters and reduces noise in an image e Tint Adjusts the colour balance in an image e Custom tint Make a customised tint setting Only available if Tint gt Custom is selected e Digital Crystal Clear Fine tunes each pixel to match surrounding pixels This produces a brilliant high definition image Dynamic contrast Automatically enhances contrast in an image A Medium setting is recommended Dynamic backlight Adjusts the brightness of the TV backlight to match lighting conditions MPEG artifact reduction Smoothes out transitions on digital pictures You can switch this feature on or off Colour enhancement Makes colours more vivid and improves the resolution of details in bright colours You can switch this feature on or off PC mode Adjusts the picture when a PC Is connected to the TV via HDMI or DVI e Picture format Changes the picture format e Horizontal shift Adjusts the picture horizontally for PC VGA DVI HDMI or YPbPr e Vertical shift Adjusts the picture vertically for PC VGA DVI
46. rved
47. tandby light on the TV blinks red Disconnect the power cable from the power outlet Wart until the TV cools down before reconnecting the power cable If the blinking reoccurs contact Philips Consumer Care You forgot the code to unlock the TV lock feature Enter 8888 The TV menu is in the wrong language Change the TV menu to your preferred language When turning the TV on off to standby you hear a creaking sound from the TV chassis e No action is required The creaking sound Is normal expansion and contraction of the TV as it cools down and warms up This does not impact performance TV channel issues Previously installed channels do not appear in the channel list e Check that the correct channel list is selected No digital channels were found during the installation Check that the TV supports DVB T or DVB C in your country See the listed countries on the back of the TV Picture issues The TV is on but there is no picture e Check that the antenna is properly connected to the TV e Check that the correct device is selected as the T V source There is sound but no picture Check that the picture settings are correctly set There is poor TV reception from an antenna connection e Check that the antenna is properly connected to the TV Loudspeakers unearthed audio devices neon lights high buildings and other large objects can influence reception quality If possib
48. u to enter a code J Enter your code using Numeric buttons The TV lock menu appears 4 Press AY to select Lock or Unlock 5 Press OK to confirm L gt All channels and connected devices are locked or unlocked Note f you select Lock you have to enter your code every time you turn on your TV to access all channels and connected devices Lock one or more channels 1 When watching TV press OK to display the channel grid 2 Press AV to select a channel to lock 3 Press OPTIONS L gt The channel options menu appears 4 Press AY to select Lock channel and press OK to enter L gt A code setup screen prompts you to enter your current code only at first selection 5 Enter your code and press OK 6 Repeat the steps to lock more channels Restart the TV for the change to take effect Unlock one or more channels 1 when watching T V press OK to display the channel grid 2 Press AV to select a locked channel to unlock 3 Press OPTIONS L gt The channel options menu appears 4 Press AY to select Unlock channel and press OK L gt A code setup screen prompts you to enter your current code only at first selection EN 17 English 5 Enter your code and press OK 6 Repeat the process to unlock more channels Restart the TV for the change to take effect f you use P on your remote control to switch between channels the locked channe
49. ubtitles Enable subtitles on digital TV channels 1 when watching digital channels press SUBTITLE L gt The Subtitle mode menu appears 2 Select On to display subtitles always or On during mute to display subtitles only when audio is muted 3 Press OK to enable subtitles Select a subtitle language on digital TV channels When you select a subtitle language on a digital TV channel as described below the preferred subtitle language set in the installation menu is temporarily overruled 1 Press amp MENU 2 Press Av to select Setup gt Features gt Subtitle language W Press OK or P to enter the list of available languages Press AV to select a subtitle language Un Press OK to enable your selection Tip You can also access Subtitle language menu while watching TV by pressing amp OPTIONS gt Subtitle language Use the TV clock You can display a clock on the TV screen The clock displays the current time using time data received from your TV service operator Display the TV clock 1 When watching TV press OPTIONS L gt The TV option menu appears x Select Clock Press OK Note To disable the clock repeat the above procedure Change the clock mode Press MENU Press AY 4b to select Setup gt Installation gt Clock gt Auto clock Press OK or P to enter the Auto clock menu Press AY to sele
Download Pdf Manuals
Related Search