JBL CONTROL® SERIES 2-Way, Dual 4" Bookshelf/Wall-Mount/Corner-Mount Speaker
Contents
1. a similar way See the owner s guides that were included with your amplifier receiver and television to confirm connection procedures 1 Strip 1 4 of wire 2 Press and push connector 3 Insert bare end release push connector BLACK NO STRIPE STRIPE Speaker Wire 16 IMPORTANT Do not reverse polarities i e to or to when making connections Doing so will cause poor imaging and diminished bass response Standard Connection one channel shown STRIPE NO STRIPE Speaker rear view Receiver or Amplifier rear view Wiring diagram shows polarity connections for one channel of a stereo or home theater system 12 Rest the third JBL Control NOW speaker s rear flange in the mounting bracket as shown and complete the process Secure the mounting bracket cap with 2 screws through the bottom of the mounting bracket 13 To orient the JBL logo into the correct position pull the JBL logo slightly outward from the speaker grille and rotate The JBL logo is held in place by a spring Peel the adhesive cover off the mounting bracket covers and attach to top and bottom of mounting bracket assembly Speaker 1 Mounting Bracket Covers A 1 Mounting Bracket i Covers STAND MOUNTING IMPORTANT SAFETY NOTE CAUTION The supplied floor stand adapters facilitate installation with a variety of general purpose floo2. another component or cable In the event that your speaker ever needs service contact your local JBL dealer or distributor or visit www jbl com for a service center near you NOTE The serial number is located on the rear of the speaker housing To view it remove the four screws on the rear assembly as shown The product identification label is located behind the rear housing bracket The serial number is located on the back top area of the speaker housing between the two top rear bracket bolt holes 27 SPECIFICATIONS Frequency Response 6dB Max Recommended Amplifier Power Power Handling Continuous Peak Sensitivity 2 83V 1m Nominal Impedance Crossover Frequencies Low Frequency Transducers High Frequency Transducer Weight per Speaker 10 3 8 262mm 5 127mm EB 2 7 JBL CONTROL NOW JBL CONTROL NOW AW 80Hz 30kHz 150W 50W 300W 90dB 8 Ohms 2000Hz 18dB octave woofer 36dB octave tweeter Dual 4 100mm PolyPlas shielded 3 4 19mm Titanium laminate dome shielded waveguide 6 6 Ib 3kg 14 5 16 364mm 9 7 8 251mm E a SSS eS The maximum recommended amplifier power rating will ensure proper system headroom to allow for occasional peaks We do not recommend sustained operation at these maximum power levels 28 Declaration of Conformity We Harman Consumer Group Inc 2 route de Tours 72500 C
3. mounting bracket and rest the JBL Control NOW speaker s rear flange in the mounting bracket as shown This will support the weight of the speaker Now slide the mounting bracket cap over the assembly Secure the mounting bracket cap by inserting two 10 32 x 2 screws provided in the bottom of the mounting bracket and tightening IMPORTANT Make sure all equipment is turned off before making any connections For speaker connections use a high quality speaker wire with polarity coding The side of the wire with a ridge or other coding is usually considered positive polarity i e NOTE If desired consult your local JBL dealer about speaker wire and connection options The speakers have coded terminals that 1 Strip 1 4 of wire F accept a variety of wire connectors The most 2 Press and push connector 3 Insert bare end common connection is shown in the diagram release push connector to the left To ensure proper polarity connect BLACK each terminal on the back of the amplifier or receiver to the respective red terminal on each speaker as shown Connect the black terminals in a similar way See the owner s guides that were included with your amplifier receiver and television to Speaker Wire confirm connection procedures IM PORTANT Do not reverse polarities i e to or to when making connections Doing so will cause poor imaging and diminished bass response NO STR
4. properly install these loudspeakers please contact your dealer or a qualified installer Please do not use any power tools during installation Power tools can exert excessive and unnecessary torque which in turn can damage fasteners or other parts and accessories reducing their strength and causing possible failure of the fastener or part A failed or damaged fastener or part may not be able to perform as designed and may lead to an unsafe installation 1 Secure three corner wall mounting brackets together by using four 10 32 x 1 2 screws provided as shown 14 When deciding upon a location for the JBL Control NOW speaker take care NOT to install the mounting bracket closer than 3 to the ceiling Any closer than 3 will not allow the room needed to position and slide the JBL Control NOW speaker into the mounting bracket ceiling 3 Minimum distance from ceiling to top of bracket s horizontal mounting Appropriate anchors 3 Remove the terminal assemblies from the rear of all speakers The terminal assembly is removed by giving it a slight counterclockwise rotation Use the transparent plastic strap to pull the assembly out as shown 4 NA TNS oy Ne Si ri 2 4 Connect the small end of the multiunit wiring adapter to the rear of 6 Place the large end of the multiunit wiring adapter that is already connected spea
5. receiver to the respective red terminal on each speaker as shown Connect the black terminals in a similar way See the owner s guides that were included with your amplifier receiver and television to confirm connection procedures 1 Strip 1 4 of wire 2 Press and push connector 3 Insert bare end release push connector BLACK NO STRIPE STRIPE Speaker Wire IMPORTANT Do not reverse polarities i e to or to when making connections Doing so will cause poor imaging and diminished bass response Standard Connection one channel shown STRIPE NO STRIPE Speaker rear view Receiver or Amplifier rear view Wiring diagram shows polarity connections for one channel of a stereo or home theater system 21 2 CHANNEL WIRING FOR EVEN SOUND DISTRIBUTION 1 Use the even sound distribution connection for even sound distribution through both channels Run the sets of paired wires out two wire access holes through the pole mount bracket as shown NOTE This procedure is applicable for both large and small diameter drop tubes A large diameter drop tube is shown here Pole Mount Bracket Cap Pole Mount Bracket SA RO Wire Access Holes 2 Channel wiring for even sound distribution 2 Remove the terminal assemblies from the rear of all speakers The terminal assembly is removed by rotating it s
6. the speakers where they best integrate into your living environment without sacrificing performance UNPACKING THE SPEAKERS If you suspect damage from transit report it immediately to your dealer Keep the shipping carton and packing materials for future use Included JBL Control NOW Speaker 2 10 32 x 2 2 10 32 x 1 2 Corner Wall Mount Bracket Screws 5 1 1 4 20 x 1 Screw eo B Corner Wall Mount Bracket Stand Mount e 0 Bracket 2 Bracket Covers 2 8 32 x 1 2 Screws Multiunit Wiring Adapter PLACEMENT JBL Control NOW speakers are perhaps the most flexible and versatile loud speakers ever developed There are numerous mounting options The JBL Control NOW speaker can be wall mounted or corner mounted sit on a shelf or be used with floor stands Two three or four speakers can be joined together to create loudspeaker solutions for virtually any application Use single units as shelf stand or wall mounted speakers in traditional stereo or home theater applications Join two speakers together to form a visually striking array in single channel applications or as a single point stereo or surround speaker such as rear surround left and rear surround right Connect three speakers around an outer corner and send full range sound throughout two adjacent rooms Suspend four JBL Control NOW speakers from the ceiling using standard ceiling fan hardware and the optional pol
7. BL dealer about speaker wire and connection options The speakers have coded terminals that 1 Strip 1 4 of wire 2 Press and p shi accept a variety of wire connectors The most 3 Insert bare end common connection is shown in the diagram release push connector to the left To ensure proper polarity connect BLACK each terminal on the back of the amplifier or receiver to the respective red terminal on each speaker as shown Connect the black terminals in a similar way See the owner s guides that were included with your amplifier receiver and television to Speaker Wire confirm connection procedures IMPORTANT Do not reverse polarities i e to or to when making connections Doing so will cause poor imaging and diminished bass response NO STRIPE STRIPE Standard Connection one channel shown STRIPE NO STRIPE Speaker rear view Receiver or Amplifier rear view Wiring diagram shows polarity connections for one channel of a stereo or an eek home theater system 23 2 CHANNEL STEREO WIRING 3 Connect the small end of the multiunit wiring adapter to the rear of speakers 1 Use the stereo sound distribution connection for a smaller home theater stereo D and B as shown environment Run the sets of paired wires out two opposite wire access holes through the pole mount bracket as shown NOTE This pro
8. Bracket Cap Cotter Pin Pinholes Pole Mount Bracket Pole Mount Bracket 4 The pole mount bracket can now hold the weight of the speakers FOR SMALLER DIAMETER DROP TUBES 2B When using a smaller drop tube use the pole bushing when running the wiring down through pole mount bracket cap This will help to eliminate pole wobble Pole Mount Bracket Clevis Pin 19 SPEAKER WIRING There are four possible ways of wiring the JBL Control NOW speakers when using the pole mount kit 2B Stereo sound distribution Use this connection for a smaller 1 Use the cable assembly provided to wire the units for a single channel home theater stereo environment Cable Assembly Channel 1 Channel 2 2 Multiunit Multiunit Wiring Adapter Wiring Adapter Terminal Single channel wiring diagram Assemblies 2 Use the multiunit wiring adapters to wire the units for two channels 2 Channel wiring diagram for stereo sound distribution NOTE There are two options for 2 channel wiring 2A Even sound distribution Use this connection for even sound distribution through both channels This may be more 3 Use four sets of cables to wire the units for four channels appropriate for larger rooms Channel 2 Channel 3 Channela Channel 2 Channel 1 Channel 1 e oye Clee B Channel B Channel 4 Multiunit Wiring Adapter NN Z
9. E If desired consult your local JBL dealer about speaker wire and connection options The speakers have coded terminals that 1 Strip 1 4 of wire 2 Press and p shi accept a variety of wire connectors The most 3 Insert bare end common connection is shown in the diagram release push connector to the left To ensure proper polarity connect BLACK each terminal on the back of the amplifier or receiver to the respective red terminal on each speaker as shown Connect the black terminals in a similar way See the owner s guides that were included with your amplifier receiver and television to Speaker Wire confirm connection procedures NO STRIPE STRIPE IMPORTANT Do not reverse polarities i e to or to when making connections Doing so will cause poor imaging and diminished bass response Standard Connection one channel shown STRIPE NO STRIPE Speaker rear view Receiver or Amplifier rear view Wiring diagram shows polarity connections for one channel of a stereo or HDi eek home theater system 4 CHANNEL WIRING 1 Run the four sets of paired wires out the wire access holes as shown NOTE This procedure is applicable for both large and small diameter drop tubes A large diameter drop tube is shown here Pole Mount Bracket Wire Access Holes 4 Channel wiring 2 Connect the wires to the te
10. IPE STRIPE Standard Connection one channel shown STRIPE NO STRIPE Speaker rear view Receiver or Amplifier rear view Wiring diagram shows polarity connections for one channel of a stereo or n BACKES home theater system Mounting Bracket side view 10 32 x 2 Screws 2 side view 9 To orient the JBL logo into the correct position pull the JBL logo slightly outward from the speaker grille and rotate The JBL logo is held in place by a spring Peel the adhesive cover off the mounting bracket covers and attach to the top and bottom of the mounting assembly 6 Place the large end of the multiunit wiring adapter into the second speaker to be installed Slide the multiunit wiring adapter into the rear of the speaker aus n at a slight angle and rotate clockwise Covers Already connected to the other speaker 7 Connect the terminal assembly to the back of the multiunit wiring adapter It will snap securely into place Mounting Bracket Covers Already connected to the other speaker 11 CONNECT AS TWO CHANNELS CAUTION The customer is responsible for proper selection and use of mounting hardware available through hardware stores to properly and safely wall mount the speakers The JBL Control NOW speaker was designed to be easily installed However if you are unable to clearly and fully understand and follow the instruct
11. JBL JBL CONTROL SERIES JBL CONTROL NOW JBL CONTROL NOW AW OWNER S GUIDE TABLE OF CONTENTS UNPACKING THE SPEAKERS 2 PLAGEIMEN m 3 WALL SURFACE MOUNTING 4 WALL CORNER MOUNTING 6 WALL CEILING CORNER MOUNTING 8 HALF ROUND 10 3 4 ROUND 14 STAND MOUNTING 0 0 00 ccc eee eee 17 FOUR SPEAKER ARRAY 18 UNPACKING THE BRACKET AND CABLE 18 MAINTENANCE AND 2 SPEDIFICATIUNS 28 JBL CONTROL NOW LOUDSPEAKERS For more than 60 years we have been providing JBL audio equipment for top concert halls recording studios and movie theaters around the world becoming the hands down choice of leading recording artists and sound engineers With JBL Control NOW loudspeakers innovative technologies such as titanium laminate dome tweeters PolyPlas transducer reinforcement and a patented controlled directivity Bi Radial horn are available to you JBL Control NOW speakers are unique in their ability to deliver excellent performance over an extremely wide listening area Therefore the conventional placement guidelines outlined below can often be relaxed somewhat to offer you the flexibility of placing
12. agnetically shielded you can place them near a CRT TV without worrying about the field distorting the TV picture For surround channel use place speakers in corners on the wall on bookshelves or on stands alongside the listening position Final placement depends on room acoustics availability of space and your listening preference In 6 or 7 channel configurations place the rear channel s behind the listening position as shown in Figure 2 NOTE A JBL powered subwoofer will add impact and realism to both music and film soundtracks Contact your JBL dealer for recommendations on subwoofer models for your application Center Channel Channel Channel Subwoofer optional Left eT Right Surround Channel Surround Channel Center Rear Channel Channel Channel e lt 2 lt 2 Figure 2 This overhead view shows a typical home theater plan Left right rear channels are for a 7 channel system The center rear channel is for a 6 channel system Left Rear Right Rear WALL SURFACE NOUNTING When deciding upon a location for the JBL Control NOW speaker take care NOT to install the mounting bracket closer than 3 horizontal and 8 1 2 vertical to the ceiling Any closer than the minimum measurements will not allow the room needed to position and slide the JBL Control NOW speaker into the mounting bracket CAUTION The customer is responsible for proper selection and use of mounting hardware available through
13. aker connections use a high quality speaker wire with polarity coding The side of the wire with a ridge or other coding is usually considered positive polarity i e NOTE If desired consult your local JBL dealer about speaker wire and connection options The speakers have coded terminals that accept a variety of wire connectors The most common connection is shown in the diagram to the left To ensure proper polarity connect each terminal on the back of the amplifier or receiver to the respective red terminal on each speaker as shown Connect the black terminals in a similar way See the owner s guides that were included with your amplifier receiver and television to confirm connection procedures 1 Strip 1 4 of wire 2 Press and push connector 3 Insert bare end release push connector BLACK NO STRIPE STRIPE Speaker Wire IMPORTANT Do not reverse polarities i e to or to when making connections Doing so will cause poor imaging and diminished bass response Standard Connection one channel shown STRIPE NO STRIPE Speaker rear view Receiver or Amplifier rear view Wiring diagram shows polarity connections for one channel of a stereo or home theater system 4 The mounting bracket is designed to trap the flange of the JBL Control NOW speaker by securing the mounting bracket cap with two s
14. cedure is applicable for both large and small diameter drop tubes A large diameter drop tube is shown here Cap 4 Place speakers D and B with connectors attached on the pole mount bracket as shown Run the wiring for the multiunit wiring adapter through the wire access holes as shown Drop Tube Multiunit Wiring Adapter i toconnectto speaker A Pole Mount Bracket WA Multiunit Wiring Adapter toconnectto speaker C Connector Wire Access Holes Wire Access Holes 2 Channel wiring for stereo sound distribution 2 adds aida A 5 Slide the large end of the multiunit wiring adapter that is already attached y g to speaker B into the rear of speaker C at a slight angle and rotate clockwise as shown This end is connected to speaker B 6 Connect the terminal assembly to the back of the multiunit wiring adapter It will snap securely into place This end is connected to speaker B 24 7 Connect the wires to the terminal assembly and place the speaker on the pole mount bracket Repeat this process with speaker A Return to the installation procedures and continue IMPORTANT Make sure all equipment is turned off before making any connections For speaker connections use a high quality speaker wire with polarity coding The side of the wire with a ridge or other coding is usually considered positive polarity i e NOT
15. crews through the bottom of the mounting bracket Rest the JBL Control NOW speaker s rear flange in the mounting bracket as shown This will support the weight of the speaker Now slide the mounting bracket cap over the assembly Secure the mounting bracket cap by inserting two 10 32 x 2 screws provided in the bottom of the mounting bracket and tightening Mounting Bracket Cap Mounting Bracket side view 10 32 x 2 Screws 2 side view Ceiling line Em 10 32 x 2 Screws 2 Mounting Bracket shown as looking through the speaker 5 To orient the JBL logo into the correct position pull the JBL logo slightly outward from the speaker grille and rotate The JBL logo is held in place by a spring Peel the adhesive cover off the mounting bracket cover and attach to bottom of mounting assembly i Mounting Bracket Cover WALL CEILING CORNER MOUNTING VERTICAL MOUNTING ONLY CAUTION The customer is responsible for proper selection and use of mounting hardware available through hardware stores to properly and safely wall mount the speakers The JBL Control NOW speaker was designed to be easily installed However if you are unable to clearly and fully understand and follow the instructions in this manual or if you are unsure of your ability to properly install these loudspeakers please contact your dealer or a qualified installer Please do not use any power tools during installation P
16. e mount bracket not included Configure each four speaker array for use as a single channel or single point stereo This owner s guide will cover the installation and wiring procedures for each mounting option Simply decide how you will mount and use the speakers and then follow the instructions for your specific application Please note that while the JBL Control NOW AW speaker is an all weather outdoor loudspeaker it is not waterproof The speaker should not be submerged or directly exposed to water ice snow or sustained moisture JBL Control NOW speakers are designed for indoor use only STEREO Before deciding where to place your speakers survey your room and think about placement Keep the following points in mind and use Figure 1 as a guide e For best results place the speakers 6 8 1 5m 2 5m apart Position each speaker so that the tweeter is directed toward the listening area e Generally bass output will increase as the speaker is moved closer to a wall or corner e Refer to the Home Theater section at right if you also plan to use the speakers for home theater reproduction e Left Right Channel Channel Listening Position Figure 1 Experiment with speaker placement to obtain the best bass level and stereo imaging in your room HOME THEATEH For front channel use place one speaker on the left and another on the right along either side of the television monitor Since the speakers are m
17. ead to an unsafe installation 1 Secure two corner wall mounting brackets together by using two 10 32 x 1 2 screws provided as shown Attach the mounting bracket to the wall 10 32 x 1 2 Screws 2 v When deciding upon a location for the JBL Control NOW speaker take care NOT to install the mounting bracket closer than 3 horizontal and 8 1 2 vertical to the ceiling Any closer than the minimum measurements will not allow the room needed to position and slide the JBL Control NOW speaker into the mounting bracket 8 1 2 Minimum distance from ceiling vertical mount 3 Minimum distance from ceiling horizontal mount N Pd 10 2 Attach the mounting bracket to the wall Be sure to use appropriate anchors Appropriate anchors 3 Remove the terminal assemblies from the rear of both speakers The terminal assembly is removed by giving it a slight counterclockwise rotation Use the transparent plastic strap to pull the assembly out as shown 4 Connect the small end of the multiunit wiring adapter to one of the speaker rears as shown 5 The mounting bracket is designed to trap the flange of the JBL Control NOW 8 Now connect the wires to the terminal assembly speaker by securing the mounting bracket cap with two screws through the bottom of the mounting bracket Run the loose end of the multiunit wiring adapter through the rear cable management hole in the
18. ems it is the customer s responsibility to check with the fan pole assembly manufacturer or dealer to determine whether that specific pole mount assembly is capable of correctly and securely attaching to the PMB and handling the weight and proportions of these loudspeakers in a safe and stable manner JBL Inc disclaims any liability for the selection of fan pole assemblies and or correct compatibility between the selected fan pole assembly and the JBL Control NOW PMB UNPACKING THE BRACKET AND CABLE KIT Carefully unpack the bracket and cable assembly If you suspect damage from transit report it immediately to your dealer and or delivery service Keep the shipping carton and packing materials for future use Open the package and verify the following contents A Included ATTACHING POLE TO POLE MOUNT BRACKET Pole Bushing FOR LARGER DIAMETER DROP TUBES smaller diameter drop tubes 1 Run the appropriate wiring down through the drop tube Slide the drop tube through the pole mount bracket cap Cotter Pin Clevis Pin Drop Tube Pole Mount Bracket Cover Cable Assembly 18 2A Slide the pole mount bracket up onto the drop tube aligning the pinholes 3 Slide the clevis pin through the aligned holes in the pole mount bracket and on the bracket with those on the drop tube drop tube Secure the clevis pin by inserting the cotter pin through the hole in the clevis pin Pole Mount
19. hardware stores to properly and safely wall mount the speakers The JBL Control NOW speaker was designed to be easily installed However if you are unable to clearly and fully understand and follow the instructions in this manual or if you are unsure of your ability to properly install these loudspeakers please contact your dealer or a qualified installer Please do not use any power tools during installation Power tools can exert excessive and unnecessary torque which in turn can damage fasteners or other parts and accessories reducing their strength and causing possible failure of the fastener or part A failed or damaged fastener or part may not be able to perform as designed and may lead to an unsafe installation 1 Run the wiring to the location desired for mounting the JBL Control NOW speaker 2 Using a level secure the mounting bracket to the wall Be sure to use an appropriate anchor 3 Minimum distance from ceiling to top of bracket horizontal mount Corner Wall Mount Bracket Assembly 8 1 2 Minimum distance from ceiling to top of bracket Sie vertical mount Appropriate anchors NOTE There are two cable access holes provided in the Wall Mount Assembly IMPORTANT Make sure all equipment is turned off before making any connections For speaker connections use a high quality speaker wire with polarity coding The side of the wire with a ridge or other coding is usually co
20. hateau du Loir France declare in own responsibility that the products described in this owner s manual are in compliance with technical standards EN 61000 6 3 2001 EN 61000 6 1 2001 j Laurent Rault Harman Consumer Group Inc Ch teau du Loir France 4 08 Features specifications and appearance are subject to change without notice JBL and Bi Radial are trademarks of Harman International Industries Incorporated registered in the United States and or other countries JBL Control NOW PolyPlas and Pro Sound Comes Home are trademarks of Harman International Industries Incorporated PRO SOUND COMES HOME Harman Consumer Group Inc 250 Crossways Park Drive Woodbury NY 11797 USA 8500 Balboa Boulevard Northridge CA 91329 USA 2 route de Tours 72500 Chateau du Loir France www jbl com O 2008 Harman International Industries Incorporated All rights reserved Part No 406 000 05609 E H A Harman International Company
21. i i Multiunit Wiring Adapter 2 Channel wiring diagram for even sound distribution 2 4 Channel wiring diagram 20 SINGLE CHANNEL WIRING 1 Use the cable assembly provided Run the cable assembly down the drop tube run the four sets of paired wires out through the wire access holes as shown NOTE This procedure is applicable for both large and small diameter drop tubes A large diameter drop tube is shown here Pole Mount Bracket Wire Access Holes Single channel wiring NOTE This procedure is applicable for both large and small diameter drop tubes A large diameter drop tube is shown here 2 Connect the wires to the terminal assembly of each speaker as shown Place the speaker on the mounting bracket as shown in step 6 of the mounting bracket installation procedures Return to the installation procedures and continue IMPORTANT Make sure all equipment is turned off before making any connections For speaker connections use a high quality speaker wire with polarity coding The side of the wire with a ridge or other coding is usually considered positive polarity i e NOTE If desired consult your local JBL dealer about speaker wire and connection options The speakers have coded terminals that accept a variety of wire connectors The most common connection is shown in the diagram to the left To ensure proper polarity connect each terminal on the back of the amplifier or
22. ion is shown in the diagram to the left To ensure proper polarity connect each terminal on the back of the amplifier or receiver to the respective red terminal on each speaker as shown Connect the black terminals in a similar way See the owner s guides that were included with your amplifier receiver and television to confirm connection procedures 1 Strip 1 4 of wire 2 Press and push connector 3 Insert bare end release push connector BLACK NO STRIPE STRIPE Speaker Wire IMPORTANT Do not reverse polarities i e to or to when making connections Doing so will cause poor imaging and diminished bass response Standard Connection one channel shown STRIPE NO STRIPE Speaker rear view Receiver or Amplifier rear view Wiring diagram shows polarity connections for one channel of a stereo or home theater system An alternate orientation shown here 17 FOUR SPEAKER ARRAY USING THE OPTIONAL POLE MOUNT BRACKET PIVIB CAUTION SPEAKER IDENTIFICATION CHART The JBL Control NOW PMB Pole Mount Bracket facilitates installation of the D JBL Control NOW and JBL Control NOW AW loudspeakers with a variety of general purpose ceiling fan pole assemblies available from many manufacturers Since different fan pole assemblies will have different weight capacities pole diameters and mounting syst
23. ions in this manual or if you are unsure of your ability to properly install these loudspeakers please contact your dealer or a qualified installer Please do not use any power tools during installation Power tools can exert excessive and unnecessary torque which in turn can damage fasteners or other parts and accessories reducing their strength and causing possible failure of the fastener or part A failed or damaged fastener or part may not be able to perform as designed and may lead to an unsafe installation 1 Secure two corner wall mounting brackets together by using two 10 32 x 1 2 screws provided as shown Attach the mounting bracket to the wall When deciding upon a location for the JBL Control NOW speaker take care NOT to install the mounting bracket closer than 3 horizontal and 8 1 2 vertical to the ceiling Any closer than the minimum measurements will not allow the room needed to position and slide the JBL Control NOW speaker into the mounting bracket 8 1 2 Minimum distance from ceiling vertical mount 3 Minimum distance from ceiling horizontal mount 12 2 Attach the mounting bracket to the wall Be sure to use appropriate anchors Appropriate anchors 3 Connect the wires to the terminal assembly of each of the JBL Control NOW speakers a gt UF IMPORTANT Make sure all equipment is turned off before making any connections For speaker connectio
24. ker 1 as shown to speaker 1 into speaker 2 by sliding the multiunit wiring adapter into the rear of the speaker at a slight angle and rotate clockwise This end is connected to the first speaker now resting in the Corner Wall Mount Bracket 5 The mounting bracket is designed to trap the flange of the JBL Control NOW 7 Connect the small end of an additional multiunit wiring adapter to the speaker speaker by securing the mounting bracket cap with two screws through the rear as shown bottom of the mounting bracket Run the loose end of the multiunit wiring adapter through the rear cable management hole in the mounting bracket and rest the JBL Control NOW speaker s rear flange in the mounting bracket as shown This will support the weight of the speaker Slide the mounting bracket cap over the assembly Secure the mounting bracket cap by inserting two 10 32 x 2 screws provided in the bottom of the mounting bracket and tightening This end is connected to the first speaker now resting in the Corner Wall Mount Bracket 8 Rest the second JBL Control NOW speaker s rear flange in the mounting bracket as shown and complete the process Secure the mounting bracket cap with two 10 32 x 2 screws through the bottom of the mounting bracket 10 32 x 2 Screws 2 10 32 x 2 Screws 2 Mounting Bracket side view 10 32 x 2 Screws 2 side view 15 9 Place the large end of the multiunit wiring adapte
25. lifier or receiver to the respective red terminal on each speaker as shown Connect the black terminals in a similar way See the owner s guides that were included with your amplifier receiver and television to confirm connection procedures IMPORTANT Do not reverse polarities i e to or to when making connections Doing so will cause poor imaging and diminished bass response 1 Strip 1 4 of wire 2 Press and push connector 3 Insert bare end release push connector BLACK NO STRIPE STRIPE Speaker Wire Standard Connection one channel shown STRIPE NO STRIPE Speaker rear view Receiver or Amplifier rear view Wiring diagram shows polarity connections for one channel of a stereo or n home theater system 4 The mounting bracket is designed to trap the flange of the JBL Control NOW speaker by securing the mounting bracket cap with two screws through the side of the mounting bracket Rest the JBL Control NOW speaker s flange in the mounting bracket as shown This will support the weight of the speaker Now slide the mounting bracket cap over the assembly Secure the mounting bracket cap by inserting two 10 32 x 2 screws provided in the side of the mounting bracket and tightening 10 32 x 2 Screws 2 Mounting Bracket Mounting Bracket shown as looking through the speake
26. lightly counterclockwise as shown Use the transparent plastic strap to pull the terminal assembly out as shown I e 22 3 Connect the small end of the multiunit wiring adapter to the rear of speakers A and B as shown 4 Place speakers A and B with connectors attached on the pole mount bracket as shown Run the wiring for the multiunit wiring adapter through the wire access holes as shown Pole Mount Bracket Wire Access Multiunit Wiring Adapter N Multiunit Wiring Adapter to connectto speaker D toconnectto speaker C 5 Slide the large end of the multiunit wiring adapter that is already attached to speaker A into the rear of speaker C at a slight angle and rotate clockwise as shown This end is connected to speaker A 6 Connect the terminal assembly to the back of the multiunit wiring adapter as shown It will snap securely into place This end is connected to speaker A 7 Connect the wires to the terminal assembly and place the speaker on the pole mount bracket Repeat this process with speaker D Return to the installation procedures and continue IMPORTANT Make sure all equipment is turned off before making any connections For speaker connections use a high quality speaker wire with polarity coding The side of the wire with a ridge or other coding is usually considered positive polarity i e NOTE If desired consult your local J
27. nd follow the instructions in this manual or if you are unsure of your ability to properly install these loudspeakers please contact your dealer or a qualified installer Please do not use any power tools during installation Power tools can exert excessive and unnecessary torque which in turn can damage fasteners or other parts and accessories reducing their strength and causing possible failure of the fastener or part A failed or damaged fastener or part may not be able to perform as designed and may lead to an unsafe installation When deciding upon a location for the JBL Control NOW speaker take care NOT to install the mounting bracket closer than 3 horizontal and 8 1 2 vertical to the ceiling Any closer than the minimum measurements will not allow the room needed to position and slide the JBL Control NOW speaker into the mounting bracket 1 Run the wiring to the location desired for mounting the JBL Control NOW speaker Corner Wall Mount Bracket Assembly NOTE There are two cable access holes provided in the Wall Mount Assembly 2 Attach the mounting bracket to the wall Be sure to use appropriate anchors 3 Minimum distance from ceiling horizontal mount 8 1 2 Minimum distance from ceiling vertical mount _ 8 Appropriate anchors 3 Connect the wires to the JBL Control NOW speaker IMPORTANT Make sure all equipment is turned off before making any connections For spe
28. ns use a high quality speaker wire with polarity coding The side of the wire with a ridge or other coding is usually considered positive polarity i e NOTE If desired consult your local JBL dealer about speaker wire and connection options The speakers have coded terminals that accept a variety of wire connectors The most common connection is shown in the diagram to the left To ensure proper polarity connect each terminal on the back of the amplifier or receiver to the respective red terminal on each speaker as shown Connect the black terminals in a similar way See the owner s guides that were included with your amplifier receiver and television to confirm connection procedures 1 Strip 1 4 of wire 2 Press and push connector 3 Insert bare end release push connector BLACK NO STRIPE STRIPE Speaker Wire IMPORTANT Do not reverse polarities i e to or to when making connections Doing so will cause poor imaging and diminished bass response Standard Connection one channel shown STRIPE NO STRIPE Speaker rear view Receiver or Amplifier rear view Wiring diagram shows polarity connections for one channel of a stereo or oe home theater system 4 The mounting bracket is designed to trap the flange of the JBL Control NOW 5 Now rest the second JBL Control NOW speaker s rear flange in the mo
29. nsidered positive polarity i e NOTE If desired consult your local JBL dealer about speaker wire and connection options The speakers have coded terminals that accept a variety of wire connectors The most common connection is shown in the diagram to the left To ensure proper polarity connect each terminal on the back of the amplifier or receiver to the respective red terminal on each speaker as shown Connect the black terminals in a similar way See the owner s guides that were included with your amplifier receiver and television to confirm connection procedures IMPORTANT Do reverse polarities i e to or to when making connections Doing so will cause poor imaging and diminished bass response 1 Strip 1 4 of wire 2 Press and push connector 3 Insert bare end release push connector BLACK NO STRIPE STRIPE Speaker Wire Standard Connection one channel shown STRIPE NO STRIPE Speaker rear view Receiver or Amplifier rear view Wiring diagram shows polarity connections for one channel of a stereo or home theater system 4 The mounting bracket is designed to trap the flange of the JBL Control NOW speaker by securing the mounting bracket cap with two screws through the bottom of the mounting bracket Rest the JBL Control NOW speaker s rear flange in the mounting bracket as sho
30. ower tools can exert excessive and unnecessary torque which in turn can damage fasteners or other parts and accessories reducing their strength and causing possible failure of the fastener or part A failed or damaged fastener or part may not be able to perform as designed and may lead to an unsafe installation When deciding upon a location for the JBL Control NOW speaker take care NOT to install the mounting bracket closer than 3 to a side wall Any closer than 3 will not allow the room needed to position and slide the JBL Control NOW speaker into the mounting bracket 3 Minimum distance from wall 1 Run the wiring to the location desired for mounting the JBL Control NOW speaker 2 Attach the mounting bracket to the wall Be sure to use appropriate anchors Appropriate anchors 3 Connect the wires to the JBL Control NOW speaker Ve E IMPORTANT Make sure all equipment is turned off before making any connections For speaker connections use a high quality speaker wire with polarity coding The side of the wire with a ridge or other coding is usually considered positive polarity i e NOTE If desired consult your local JBL dealer about speaker wire and connection options The speakers have coded terminals that accept a variety of wire connectors The most common connection is shown in the diagram to the left To ensure proper polarity connect each terminal on the back of the amp
31. r P Mounting Top Cap Bracket This illustration shows speaker viewed from beneath 10 32 x 2 Screws 2 5 To orient the JBL logo into the correct position pull the JBL logo slightly outward from the speaker grille and rotate The JBL logo is held in place by a spring Peel the adhesive cover off the mounting bracket cover and attach to sides of the mounting assembly Bracket Cover HALF ROUND WALL MOUNTING HORIZONTAL OR VERTICAL NOTE Decide whether you will connect the speakers as a single channel or two separate channels and follow the appropriate instructions on the following pages CONNECT AS A SINGLE CHANNEL CAUTION The customer is responsible for proper selection and use of mounting hardware available through hardware stores to properly and safely wall mount the speakers The JBL Control NOW speaker was designed to be easily installed However if you are unable to clearly and fully understand and follow the instructions in this manual or if you are unsure of your ability to properly install these loudspeakers please contact your dealer or a qualified installer Please do not use any power tools during installation Power tools can exert excessive and unnecessary torque which in turn can damage fasteners or other parts and accessories reducing their strength and causing possible failure of the fastener or part A failed or damaged fastener or part may not be able to perform as designed and may l
32. r stands available from many manufacturers Since different stands will have different weight capacities and stability characteristics it is the customer s responsibility to check with the stand manufacturer or dealer to ascertain whether that specific stand is capable of handling the weight and proportions of these loudspeakers in a safe and stable manner JBL Inc disclaims any liability for the selection of suitable floor stands and or correct compatibility between the selected stand and the supplied stand adapter 1 Attach the stand mounting bracket to the stand with the 1 4 20 x 1 screw as shown 2 Run the wiring as shown Note trough in Stand Mount Bracket for cable management 1 4 20 x 1 Screw Provided Stand Mount Bracket Stand 3 Place the JBL Control NOW speaker on the stand mount bracket and stand as shown 4 Use two 8 32 x 1 2 screws provided to secure the JBL Control NOW speaker to the stand 5 Attach wires Y 8 32 1 2 Screws IMPORTANT Make sure all equipment is turned off before making any connections For speaker connections use a high quality speaker wire with polarity coding The side of the wire with a ridge or other coding is usually considered positive polarity i e NOTE If desired consult your local JBL dealer about speaker wire and connection options The speakers have coded terminals that accept a variety of wire connectors The most common connect
33. r that is already installed in speaker 2 into speaker 3 by sliding a multiunit wiring adapter into the rear of it at a slight angle and rotate clockwise This end is connected to the second speaker currently resting in the Corner Wall Mount Bracket assembly 10 Connect the terminal assembly to the back of the second multiunit wiring adapter It will snap securely into place The other end of the multiunit wiring adapter will already be connected to the other speaker already mounted in the corner wall mount bracket assembly This end is connected to the second speaker currently resting in the Corner Wall Mount Bracket Assembly 11 Connect the wires to the terminal assembly and place the speaker on the remaining bracket ome J S IMPORTANT Make sure all equipment is turned off before making any connections For speaker connections use a high quality speaker wire with polarity coding The side of the wire with a ridge or other coding is usually considered positive polarity i e NOTE If desired consult your local JBL dealer about speaker wire and connection options The speakers have coded terminals that accept a variety of wire connectors The most common connection is shown in the diagram to the left To ensure proper polarity connect each terminal on the back of the amplifier or receiver to the respective red terminal on each speaker as shown Connect the black terminals in
34. rminal assembly of each speaker as shown and place the speaker on the mounting bracket as shown in step 6 of the mounting bracket installation procedures Return to the installation procedures and continue 25 SPEAKER MOUNTING After carefully placing all four speakers in the mounting bracket lightly jostle Drop Tube the speakers into place so that the pole mount bracket cap will slide down into place Tighten the pole mount bracket assembly with the four 10 32 x 2 screws provided Pole Mount Bracket Cap Pole Mount Bracket Only two speakers shown here 10 32 x 2 Screws 4 for clarity Drop Tube Place the pole mount bracket cover over the bottom visible mounting bracket by snapping it into place 26 MAINTENANCE AND SERVICE The enclosure may be cleaned using a soft cloth to remove fingerprints or to wipe off dust All wiring connections should be inspected and cleaned or remade periodically The frequency of maintenance depends on the metals involved in the connections atmospheric conditions and other factors but once per year is the minimum If a problem occurs make sure that all connections are properly made and clean If a problem exists in one loudspeaker reverse the connection wires to the left and right system If the problem remains in the same speaker then the fault is with the loudspeaker If the problem appears in the opposite speaker the cause is in
35. unting speaker by securing the mounting bracket cap with two screws through the bracket as shown and complete the process Secure the mounting bracket bottom of the mounting bracket This will support the weight of the speaker cap with two 10 32 x 2 screws through the bottom of the mounting bracket Now slide the mounting bracket cap over the assembly Secure the mounting bracket cap by inserting two 10 32 x 2 screws provided in the bottom of the mounting bracket and tightening Repeat the process with the remaining speaker Mounting Bracket Cap Mounting Bracket side view 10 32 x 2 Screws 2 10 32 x 2 Screws 2 side view 6 To orient the JBL logo into the correct position pull the JBL logo slightly outward from the speaker grille and rotate The JBL logo is held in place by a spring Peel the adhesive cover off the mounting bracket covers and attach to the top and bottom of the mounting assembly Mounting Bracket Covers 10 32 x 2 Screws 2 13 3 4 ROUND WALL IMOUNTING Speaker 1 Speaker 2 Speaker 3 CAUTION The customer is responsible for proper selection and use of mounting hardware available through hardware stores to properly and safely wall mount the speakers The JBL Control NOW speaker was designed to be easily installed However if you are unable to clearly and fully understand and follow the instructions in this manual or if you are unsure of your ability to
36. wn This will support the weight of the speaker Slide the mounting bracket cap over the assembly Secure the mounting bracket cap by inserting two 10 32 x 2 screws provided in the bottom of the mounting bracket and tightening An alternate vertical orientation is shown here Mounting Bracket Cap Vertical orientation Mounting Bracket side view Bracket Cover 10 32 x 2 Screws 2 side view 1 Mounting Bracket Vertical orientation Bracket Cover Mounting Bracket shown as looking through the speaker Regardless of whether you choose a vertical or horizontal orientation when mounting the JBL Control NOW speaker to a single wall surface you should always install the wall mounting bracket in a vertical orientation 5 To orient the JBL logo into the correct position pull the JBL logo slightly outward from the speaker grille and rotate The JBL logo is held in place by a spring Peel the adhesive cover off the mounting bracket cover and attach to the top and bottom of the mounting assembly Mounting Bracket Cover l 0 Mounting Bracket Cover WALL CORNER MOUNTING CAUTION The customer is responsible for proper selection and use of mounting hardware available through hardware stores to properly and safely wall mount the speakers The JBL Control NOW speaker was designed to be easily installed However if you are unable to clearly and fully understand a
Download Pdf Manuals
Related Search