Home

Lenco SCD-20

1. temperature or humidity Use dampened soft cloth to clean the unit Do not use strong detergent or solvent to clean the unit 3 Ensure that all electrical connections including the main plug extension leads and interconnections between pieces of equipment are properly made and in accordance with the manufacturer s instructions 4 Consult your dealer if you are ever in doubt about the installation operation or safety of your equipment LOCATION OF CONTROL CD STOP m CD BACK BUTTON kdd CD REPEAT BUTTON CD DISPLAY CD PROGRAM BUTTON CD DOOR CD NEXT BUTTONPP CD PLAY PAUSE BUTTONP Il CARRYING HANDLE 10 TELESCOPIC ANTENNA 11 DIAL SCALE 12 SPEAKER 13 PHONES JACK 14 VOLUME CONTROL 15 TUNING CONTROL 16 FUNCTION SWITCH CD FM OFF 17 FM STEREO MONO SWITCH 18 AC SOCKET 19 BATTERY COMPARTMENT Seno oS oN gt POWER SUPPLY 1 BATTERY OPERATION Remove the battery compartment door and insert 6 pieces UM2 C size batteries into the battery compartment with battery polarity positioned as indicated NOTE Werecommend the use of alkaline batteries Close the battery compartment door 2 AC OPERATION The power cord is located inside the battery compartment Plug the AC line cord into any normal household AC mains outlet in correct voltage and the mains socket RADIO OPERATION 1 Set FUNCTION SWITCH to FM position 2 Rotate the TUNING CONTROL to select a radio station 3 Adjust VOLUME C
2. ONTROL to listen to the sound level to your preference FM FM ST BAND Normally the FM STEREO MONO SWITCH should be set the STEREO position If a station is too weak or noisy select MONO to improved reception Fully extend the TELESCOPIC ANTENNA and adjust its direction for best FM reception To turn units POWER OFF simple set FUNCTION SWITCH to OFF position LISTENING TO COMPACT DISC CD CONCERNING COMPACT DISC Only compact discs identified with this mark can be used with this player chs DIGITAL AUDIO HANDLING DISCS To remove the disc from its storage case press down on the center of the case and lift the disc out Hold carefully by the edges as shown below 1 Insert the disc into the unit with the label of the disc facing up 2 Gently wipe the disc using a soft cloth from the center to the outer direction to remove dust fingerprints or any other articles on the disc surface Never use chemicals such as record sprays anti static sprays or benzene etc to clean the CD These chemicals can damage the disc surface permanently 3 To void serious scratches on CD keep them in the cases after each use Scratches can cause the laser pick up skip in the future play 4 Do not place stickers or write anything on the disc COMPACT DISC PLAYBACK Set FUNCTION switch to CD position Lift the CD DOOR up Insert a disc with the label side facing up Close the CD door The disc will rotate and th
3. WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE IMPORTANT SINCE THE CD CIRUITRY MAY CAUSE INTERFERENCE TO OTHER RADIO TUNERS NEARBY SWITCH THIS UNIT OFF WHEN NOT IN USE OR MOVE IT AWAY FROM THE AFFECTED RADIO TUNER CAUTION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The exclamation point ATTENTION To reduce the risk of The Lightening flash within the triangle is a electric shock do not remove the with arrowhead symbol warning sign alerting cover There are no user within the triangle is a the user of important serviceable parts inside the unit warning sign alerting Instructions Refer all servicing to qualified service the user of Dangerous accompanying the personnel Voltage inside the unit product DANGER LASER SAFETY THIS UNIT EMPLOYS AN OPTICALLASER BEAM SYSTEM IN THE CD MECHANISM DESIGNED WITH BUILT IN SAFEGUARDS DONOT ATTEMPT TO DISASSEMBLE REFER TO QUALIFIED SERVICE PERSONNEL EXPOSURE TO THIS INVISIBLE LASER LIGHT BEAM MAY BE HARMFUL TO THE HUMAN EYE INVISIBLE LASER RADIATION WHEN OPEN AND INTER LOCK FAILED OR DEFEATED AVOID THIS IS A CLASS 1 LASER PRODUCT USE OF CONTROLS OR ADJUSTMENTS DIRECTEXPOSURE OR PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN TO LASER BEAM HAZARDOUS LASER LIGHT BEAM EXPOSURE MAINTENANCE AND CARE 1 Read the instruction manual before operating this unit 2 Do not expose the unit to high
4. ake program memory in stop mode Pr will be shown flashing on the display Press CD BACK CD NEXT button to select a track number The track number will show on display Press the CD PROGRAM button to store the track number Pr flashes again Repeat step 3 or 4 to program other desired tracks Press CD PROGRAM button once more and all the programmed track numbers will be shown one by one Press CD PLAY PAUSE button playback will start from the first programmed track You can press CD BACK NEXT button to select the track number in memory In stop mode press STOP button to cancel the program play CON OD OP ON HEADPHONE JACK For private listening insert a 3 5 mm headphone not included into the PHONES JACK The speaker output is automatically cut off CAUTION LISTENING AT HIGH POWER FOR ALONG PERIOD COULD DAMAGE USERS EARS SPECIFICATIONS CD SECTION Channels 2 channels Optical pick up 3 beams laser Frequency response 100 Hz 16 KHz RADIO SECTION Tuning ranges FM 87 5 108 MHz Antenna FM rod antenna GENERAL Output power Max 1 2W x 2 RMS Speaker impedance 4 Ohm Phones jack 3 5 MM Power source AC 230 V 50 Hz DC 9V 6 x 1 5V UM2 C size Power consumption 10 5W Headphone impedance 4 32 Ohm Due to continuing improvement the features and the design are subject to change without notice
5. e total tracks of the disc will show on the display Press the PLAY PAUSE button Track number 1 will be shown aS a PLAYING THE ENTIRE DISC 1 Playback will start by pressing CD PLAY PAUSE button playback starts with the first track The display will show the current track number 2 To interrupt playback press CD PLAY PAUSE button The CD PLAY PAUSE indicator will be flashing 3 To resume playback press CD PLAY PAUSE button once again 4 To stop playback press CD STOP button SELECTING A DIFFERENT TRACK DURING PLAY 1 Press CD BACK or CD NEXT button on the unit continuously until the desired track number appears in the display 2 Playback starts from the desired track Press CD PLAY PAUSE button to start playback in stop mode STARTING AGAIN WITH THE TRACK THAT IS CURRENTLY PLAYING 1 Press CD BACK button once 2 The playback will start again from the beginning of the track STOPPING PLAY 1 Press CD STOP button if you wish to stop play The total track number that can be played will now appear in the display 2 Open the CD door on the unit to remove the CD REPEAT PLAY When play press CD REPEAT button once RPT will be shown flashing on the display for playing the same track only If repeat all tracks press the CD REPEAT button again RPT will be shown on the display To cancel repeat play press the CD REPEAT button until the RPT letter disappears PROGRAM PLAY Press CD PROGRAM button to m

Lenco SCD-20

Contents

Download Pdf Manuals

Related Search

Related Contents