SMC SMC6110L2 network switch
Contents
1. Mounting 3 Mounting The switch can be mounted in a standard 19 inch equipment rack or on a desktop or shelf Mounting instructions for each type of site follow Rack Mounting Before rack mounting the switch pay particular attention to the following factors Temperature Since the temperature within a rack assembly may be higher than the ambient room temperature check that the rack environment temperature is within the specified operating temperature range See page C 1 Mechanical Loading Do not place any equipment on top of a rack mounted unit Circuit Overloading Be sure that the supply circuit to the rack assembly is not overloaded Grounding Rack mounted equipment should be properly grounded Particular attention should be given to supply connections other than direct connections to the mains To rack mount devices 1 Attach the brackets to the device using the screws provided in the Bracket Mounting Kit K A Figure 3 2 Attaching the Brackets 3 3 3 Installing the Switch 2 Mount the device in the rack using four rack mounting screws not provided Be sure to secure the lower rack mounting screws first to prevent the brackets being bent by the weight of the switch H a Figure 3 3 Installing the Switch in a Rack 3 If installing a single switch only turn to Connecting to a Power Source at the end of this chapter 4 If installing multiple switches mount them in the rack2. type SV ou SJ 3 conducteurs Le cordon doit tre en mesure d acheminer un courant nominal d au moins 10 A La prise femelle de branchement doit tre du type mise la terre mise la masse et respecter la configuration NEMA 5 15P 15 A 125 V ou NEMA 6 15P 15 A 250 V Danemark La prise male d alimentation doit respecter la section 107 2 D1 de la norme DK2 1a ou DK2 5a Suisse La prise m le d alimentation doit respecter la norme SEV ASE 1011 Europe La prise secteur doit tre conforme aux normes CEE 7 7 SCHUKO LE cordon secteur doit porter la mention lt HAR gt ou lt BASEC gt et doit tre de type HO3VVF3GO 75 minimum Bitte unbedingt vor dem Einbauen des Switches die folgenden Sicherheitsanweisungen durchlesen WARNUNG Die Installation und der Ausbau des Ger ts darf nur durch Fachpersonal erfolgen Das Ger t sollte nicht an eine ungeerdete Wechselstromsteckdose angeschlossen werden Das Gerat muB an eine geerdete Steckdose angeschlossen werden welche die internationalen Sicherheitsnormen erf llt Der Ger testecker der Anschlu an das Ger t nicht der Wandsteckdosenstecker mu einen gem EN 60320 IEC 320 konfigurierten Ger teeingang haben Die Netzsteckdose mu in der N he des Ger ts und leicht zug nglich sein Die Stromversorgung des Ger ts kann nur durch Herausziehen des Ger tenetzkabels aus der Netzsteckdose unterbrochen werden Der Betri
3. A MICRA EL CHV ET ERA FES bd FARHAT RBRI Key ht AED md UE HO FAR CG EF lt CEISMREGA MAAR SHE BRI Key hea man DER 2 FEY hkeBALZUCE SL Power Cord Safety Please read the following safety information carefully before installing the switch WARNING Installation and removal of the unit must be carried out by qualified personnel only The unit must be connected to an earthed grounded outlet to comply with international safety standards e Do not connect the unit to an A C outlet power supply without an earth ground connection The appliance coupler the connector to the unit and not the wall plug must have a configuration for mating with an EN 60320 IEC 320 appliance inlet The socket outlet must be near to the unit and easily accessible You can only remove power from the unit by disconnecting the power cord from the outlet e This unit operates under SELV Safety Extra Low Voltage conditions according to IEC 60950 The conditions are only maintained if the equipment to which it is connected also operates under SELV conditions France and Peru only This unit cannot be powered from ITt supplies If your supplies are of IT type this unit must be powered by 230 V 2P T via an isolation transformer ratio 1 1 with the secondary connection point labelled Neutral connected directly to earth ground t Imp dance a la terre Important Before making connections make sure you have the correct cord set Ch
4. Now incorporated in IEEE 802 3 2002 IEEE 802 3z Defines CSMA CD access method and physical layer specifications for 1000BASE Gigabit Ethernet Now incorporated in IEEE 802 3 2002 LAN Segment Separate LAN or collision domain LED Light emitting diode used for monitoring a device or network condition Local Area Network LAN A group of interconnected computer and support devices Media Access Control MAC A portion of the networking protocol that governs access to the transmission medium facilitating the exchange of data between network nodes MIB An acronym for Management Information Base It is a set of database objects that contains information about the device Modal Bandwidth Bandwidth for multimode fiber is referred to as modal bandwidth because it varies with the modal field or core diameter of the fiber Modal bandwidth is specified in units of MHz per km which indicates the amount of bandwidth supported by the fiber for a one km distance Network Diameter Wire distance between two end stations in the same collision domain Redundant Power Supply RPS A backup power supply unit that automatically takes over in case the primary power supply should fail Glossary 3 Glossary RJ 45 Connector A connector for twisted pair wiring Switched Ports Ports that are on separate collision domains or LAN segments TIA Telecommunications Industry Association Transmission Control Protocol Internet
5. In Band Management SSH Telnet SNMP or HTTP Out of Band Management RS 232 DB 9 console port Software Loading TFTP in band or XModem out of band C 2 Standards Ci Standards IEEE 802 3 2005 Ethernet Fast Ethernet Gigabit Ethernet Full duplex flow control Link Aggregation Control Protocol IEEE 802 1D Spanning Tree Protocol IEEE 802 1w Rapid Spanning Tree Protocol ISO IEC 8802 3 Compliances Emissions Industry Canada Class A EN55022 CISPR 22 Class A EN 61000 3 2 3 FCC Class A VCCI Class A CE Mark MIC Class A Republic of Korea Only Immunity EN 61000 4 2 3 4 5 6 8 11 Safety UL 60950 1 amp CSA 60950 1 IEC 60950 1 amp EN 60950 1 C 3 IC Specifications C 4 Appendix D Ordering Information Table D 1 TigerSwitch 10 100 Products and Accessories Product Number Description SMC6110L2 8 port 10 100 Managed Switch with 2 Gigabit Combo ports SMC1GSFP SX Single port 1000BASE SX Small Form Pluggable SFP mini GBIC transceiver SMCIGSFP LX Single port 1000BASE LX Small Form Pluggable SFP mini GBIC transceiver SMCIGSFP ZX Single port 1000BASE ZX Small Form Pluggable SFP mini GBIC transceiver D 1 D Ordering Information D 2 Glossary 10BASE T IEEE 802 3 specification for 10 Mbps Ethernet over two pairs of Category 3 4 or 5 UTP cable 100BASE FX IEEE 802 3 specification for 100 Mbps Ethernet over two strand
6. System Indicators Port Status Indicators SMC se PEA o i LE _ n u Peewee je je AI a Ce Console Port 10 100 Mbps Ru 45 Ports 1000BASE T SFP Ports R Power Socket Figure 1 1 Front and Rear Panels If an SFP transceiver is plugged in the corresponding RJ 45 port is disabled for ports 9 10 1 1 1 Introduction Switch Architecture The switch employs a wire speed non blocking switching fabric This permits simultaneous wire speed transport of multiple packets at low latency on all ports The switch also features full duplex capability on all ports which effectively doubles the bandwidth of each connection This switch uses store and forward switching to ensure maximum data integrity With store and forward switching the entire packet must be received into a buffer and checked for validity before being forwarded This prevents errors from being propagated throughout the network Network Management Options With a comprehensive array of LEDs the switch provides at a glance monitoring of network and port status The switch can be managed over the network with a web browser or Telnet application or via a direct connection to the console port The switch includes a built in network management agent that allows it to be managed in band using SNMP or RMON Groups 1 2 3 9 protocols It also has an RS 232 serial port DB 9 connector on the rear panel for out of band management A PC may
7. Figure 1 1 Front and Rear Panels Figure 1 2 Port LEDs Figure 1 3 Power Supply Socket Figure 2 1 Collapsed Backbone Figure 2 2 Network Edge Deployment Figure 3 1 RJ 45 Connections Figure 3 2 Attaching the Brackets Figure 3 3 Installing the Switch in a Rack Figure 3 4 Attaching the Adhesive Feet Figure 3 5 Inserting an SFP Transceiver into a Slot Figure 3 6 Power Socket Figure 3 7 Serial Port DB 9 DTE Pin Out Figure 4 1 Making Twisted Pair Connections Figure 4 2 Network Wiring Connections Figure 4 3 Making Fiber Port Connections Figure B 1 RJ 45 Connector Pin Numbers Figure B 2 Straight through Wiring Figure B 3 Crossover Wiring xiv Chapter 1 Introduction Overview The SMC6110L2 is a Fast Ethernet switch with eight 10BASE T 100BASE TX ports and two 1000BASE T ports that operate in combination with two Small Form Factor Pluggable SFP transceiver slots see Figure 1 1 Ports 9 10 The switch also includes an SNMP based management agent which provides both in band and out of band access for managing the switch The SMC6110L2 provides a broad range of powerful features for Layer 2 switching delivering reliability and consistent performance for your network traffic It brings order to poorly performing networks by segregating them into separate broadcast domains with IEEE 802 1Q compliant VLANs and empowers multimedia applications with multicast switching and CoS services
8. Protocol TCP IP Protocol suite that includes TCP as the primary transport protocol and IP as the network layer protocol UTP Unshielded twisted pair cable Virtual LAN VLAN A Virtual LAN is a collection of network nodes that share the same collision domain regardless of their physical location or connection point in the network A VLAN serves as a logical workgroup with no physical barriers allowing users to share information and resources as though located on the same LAN Glossary 4 Index Numerics 10 Mbps connectivity rules 4 6 100 Mbps connectivity rules 4 6 1000 Mbps connectivity rules 4 6 1000BASE LH fiber cable Lengths 4 6 1000BASE LX fiber cable Lengths 4 6 1000BASE SX fiber cable Lengths 4 6 1000BASE T pin assignments B 3 ports 1 3 100BASE TX cable lengths 4 6 ports 1 2 10BASE T cable lengths 4 6 ports 1 2 A adhesive feet attaching 3 5 air flow requirements 3 1 applications central wiring closet 2 3 collapsed backbone 2 2 remote connections with fiber 2 4 VLAN connections 2 5 B brackets attaching 3 3 buffer size C 1 C cable Ethernet cable compatibility 3 1 fiber standards B 4 labeling and connection records 4 7 lengths 4 6 cleaning fiber terminators 4 4 compliances EMC C 3 safety C 3 connectivity rules 10 Mbps 4 6 100 Mbps 4 6 1000 Mbps 4 6 console port pin assignments 3 7 contents of package 3 2 cooling problems A 1 cord sets international 3 7 D desktop mo
9. connections 4 1 pinouts B 3 RMON 1 2 RS 232 port 1 2 rubber foot pads attaching 3 5 S screws for rack mounting 3 2 serial cable 1 2 port 1 2 single mode fiber optic cables 4 4 site selelction 3 1 SNMP agent 1 2 specifications compliances C 2 environmental C 1 physical C 1 power C 2 standards compliance C 2 IEEE C 3 status LEDs 1 3 surge suppressor using 3 1 switch architecture 1 2 switching introduction to 2 1 method 1 2 T Telnet A 2 temperature within a rack 3 3 troubleshooting in band access A 2 power and cooling problems A 1 switch indicators A 1 twisted pair connections 4 1 index V W VLANS web based management 1 2 tagging 2 5 Index 3 ET Index 4 Networks TECHNICAL SUPPORT From U S A and Canada 24 hours a day 7 days a week Phn 800 SMC 4 YOU 949 679 8000 Fax 949 502 3400 ENGLISH Technical Support information available at www smc com FRENCH Informations Support Technique sur www smc com DEUTSCH Technischer Support und weitere Information unter www smc com SPANISH En www smc com Ud podra encontrar la informacion relativa a servicios de soporte t cnico DUTCH Technische ondersteuningsinformatie beschikbaar op www smc com PORTUGUES Informa es sobre Suporte T cnico em www smc com SWEDISH Information om Teknisk Support finns tillg ngligt p www smc com INTERNET E mail address techsupport smc com Driver updates http www smc com index cfm ac
10. e Verify that the proper cable type is used and its length does not exceed specified limits Check the adapter on the attached device and cable connections for possible defects Replace the defective adapter or cable if necessary Power and Cooling Problems If the power indicator does not turn on when the power cord is plugged in you may have a problem with the power outlet power cord or internal power supply However if the unit powers off after running for a while check for loose power connections power losses or surges at the power outlet If you still cannot isolate the problem the internal power supply may be defective Installation Verify that all system components have been properly installed If one or more components appear to be malfunctioning such as the power cord or network cabling test them in an alternate environment where you are sure that all the other components are functioning properly A 1 A Troubleshooting In Band Access You can access the management agent in the switch from anywhere within the attached network using Telnet a web browser or other network management software tools However you must first configure the switch with a valid IP address subnet mask and default gateway If you have trouble establishing a link to the management agent check to see if you have a valid network connection Then verify that you entered the correct IP address Also be sure the port through which y
11. normally Off The unit has no power connected Diag OnGreen The system diagnostic test has completed successfully Flashing Green The system diagnostic testis in progress On Amber The system diagnostic test has detected a fault Power Supply Socket There is one power socket on the rear panel of the switch The standard power socket is for the AC power cord 100 240V 50 60Hz 0 4A Figure 1 3 Power Supply Socket Features and Benefits Connectivity Eight dual speed ports for easy Fast Ethernet integration and for protection of your investment in legacy LAN equipment e Auto negotiation enables each RJ 45 port to automatically select the optimum communication mode half or full duplex if this feature is supported by the attached device otherwise the port can be configured manually e BAR 10 100BASE TX ports with auto MDI MDI X e Unshielded UTP cable supported on all RJ 45 ports Category 3 or better for 10 Mbps connections Category 5 or better for 100 Mbps connections and Category 5 5e or 6 for 1000 Mbps connections IEEE 802 3 2005 Ethernet Fast Ethernet Gigabit Ethernet compliance ensures compatibility with standards based hubs network cards and switches from any vendor 1 4 Features and Benefits 1 Expandability Two Small Form Factor Pluggable SFP transceiver slots shared with 1000BASE T ports e Supports 1000BASE SX 1000BASE LX and 1000BASE LH SFP transceivers Performance e Tr
12. one below the other in any order 3 4 Installing an Optional SFP Transceiver 3 Desktop or Shelf Mounting 1 Attach the four adhesive feet to the bottom of the first switch Figure 3 4 Attaching the Adhesive Feet 2 Setthe device on a flat surface near an AC power source making sure there are at least two inches of space on all sides for proper air flow 3 If installing a single switch only go to Connecting to a Power Source at the end of this chapter 4 If installing multiple switches attach four adhesive feet to each one Place each device squarely on top of the one below in any order Installing an Optional SFP Transceiver Figure 3 5 Inserting an SFP Transceiver into a Slot 3 5 3 Installing the Switch The SFP slots support the following optional SFP transceivers 1000BASE SX 1000BASE LX 1000BASE LH To install an SFP transceiver do the following 1 3 Consider network and cabling requirements to select an appropriate SFP transceiver type Insert the transceiver with the optical connector facing outward and the slot connector facing down Note that SFP transceivers are keyed so they can only be installed in one orientation Slide the SFP transceiver into the slot until it clicks into place Note SFP transceivers are hot swappable The switch does not need to be powered off before installing or removing a transceiver However always first disconnect the network cable before remo
13. the following criteria against the current installation of your network Cable type Unshielded twisted pair UTP or shielded twisted pair STP cables with RJ 45 connectors Category 3 or better for 10BASE T Category 5 or better for 100BASE TX and Category 5 5e or 6 for 1000BASE T Protection from radio frequency interference emissions Electrical surge suppression Separation of electrical wires switch related or other and electromagnetic fields from data based network wiring Safe connections with no damaged cables connectors or shields 3 1 3 Installing the Switch RJ 45 Connector Figure 3 1 RJ 45 Connections Equipment Checklist After unpacking this switch check the contents to be sure you have received all the components Then before beginning the installation be sure you have all other necessary installation equipment Package Contents TigerSwitch 10 100 SMC6110L2 Four adhesive foot pads Bracket Mounting Kit containing two brackets and eight screws for attaching the brackets to the switch Power Cord either US Continental Europe or UK RS 232 console cable This Installation Guide Management Guide CD Optional Rack Mounting Equipment If you plan to rack mount the switch be sure to have the following equipment available 3 2 Four mounting screws for each device you plan to install in a rack these are not included A screwdriver Phillips or flathead depending on the type of screws used
14. the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment You may use unshielded twisted pair UTP for RJ 45 connections Category 3 or better for 10 Mbps connections Category 5 or better for 100 Mbps connections Category 5 5e or 6 for 1000 Mbps connections For fiber optic connections you may use 50 125 or 62 5 125 micron multimode fiber or 9 125 micron single mode fiber Industry Canada Class A This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the interference causing equipment standard entitled Digital Apparatus ICES 003 of the Department of Communications Cet appareil num rique respecte les limites de bruits radio lectriques applicables aux appareils num riques de Classe A prescrites dans la norme sur le mat riel brouilleur Appareils Num riques NMB 003 dict e par le minist re des Communications Japan VCCI Class A CORES FRUBRESSRESAE MAA VCCI DEE BOC OFAZATMRMEE CT COPBARERR CHAT EE PBENSRCTCEMHVET SOBSEILIKEAERNENEHR ET BEDBRENSGSCEMHVET MIC Notice Republic of Ko
15. 1 Collapsed Backbone 2 2 Application Examples 2 Network Edge Deployment With 8 1000 Mbps parallel bridging ports i e 8 distinct collision domains this switch can function as an efficient bridged node that is ideal for a meeting room environment Zero noise makes the switch inobtrusive for such a setting In the figure below the SMC6110L2 is connected to a central wiring closet via a 1000BASE SX connection The 1000BASE T RJ 45 ports on the switch are providing 10 100 Mbps full duplex connections for PCs and notebooks Wiring Closet suc a eege wemmer 1000BASE SX SMF Server Farm Edge Device Switch SMC moe ff CERRI nea 10 100 Mbps Segments r r F vg Standard LAI Figure 2 2 Network Edge Deployment 2 3 2 Network Planning Application Notes 1 2 4 Full duplex operation only applies to point to point access such as when a switch is attached to a workstation server or another switch When the switch is connected to a hub both devices must operate in half duplex mode Avoid using flow control on a port connected to a hub unless it is actually required to solve a problem Otherwise back pressure jamming signals may degrade overall performance for the segment attached to the hub As a general rule the length of fiber optic cable for a single switched link should not exceed e 1000BASE SX 550 m 1805 ft for multimode fiber e 1000BASE LX 5 km 3 1 miles for single mode fiber e 1000BAS
16. A workstation server or other device that does not forward traffic Ethernet A network communication system developed and standardized by DEC Intel and Xerox using baseband transmission CSMA CD access logical bus topology and coaxial cable The successor IEEE 802 3 standard provides for integration into the OSI model and extends the physical layer and media with repeaters and implementations that operate on fiber thin coax and twisted pair cable Fast Ethernet A 100 Mbps network communication system based on Ethernet and the CSMA CD access method Full Duplex Transmission method that allows two network devices to transmit and receive concurrently effectively doubling the bandwidth of that link Gigabit Ethernet A 1000 Mbps network communication system based on Ethernet and the CSMA CD access method IEEE Institute of Electrical and Electronic Engineers IEEE 802 3 Defines carrier sense multiple access with collision detection CSMA CD access method and physical layer specifications IEEE 802 3ab Defines CSMA CD access method and physical layer specifications for 1000BASE T Gigabit Ethernet Now incorporated in IEEE 802 3 2002 Glossary 2 Glossary IEEE 802 3u Defines CSMA CD access method and physical layer specifications for 100BASE TX Fast Ethernet Now incorporated in IEEE 802 3 2002 IEEE 802 3x Defines Ethernet frame start stop requests and timers used for flow control on full duplex links
17. E LH 70 km 43 5 miles for single mode fiber However power budget constraints must also be considered when calculating the maximum cable length for your specific environment Chapter 3 Installing the Switch Selecting a Site Switch units can be mounted in a standard 19 inch equipment rack or on a flat surface Be sure to follow the guidelines below when choosing a location The site should be atthe center of all the devices you want to link and near a power outlet be able to maintain its temperature within 0 to 50 C 32 to 122 F and its humidity within 10 to 90 non condensing provide adequate space approximately two inches on all sides for proper air flow be accessible for installing cabling and maintaining the devices allow the status LEDs to be clearly visible Make sure twisted pair cable is always routed away from power lines fluorescent lighting fixtures and other sources of electrical interference such as radios and transmitters Make sure that the unit is connected to a separate grounded power outlet that provides 100 to 240 VAC 50 to 60 Hz is within 2 m 6 6 feet of each device and is powered from an independent circuit breaker As with any equipment using a filter or surge suppressor is recommended Ethernet Cabling To ensure proper operation when installing the switch into a network make sure that the current cables are suitable for 1OBASE T 100BASE TX or 1000BASE T operation Check
18. Installed Category 5 cabling must pass tests for Attenuation Near End Crosstalk NEXT and Far End Crosstalk FEXT This cable testing information is specified in the ANSI TIA EIA TSB 67 standard Additionally cables must also pass test parameters for Return Loss and Equal Level Far End Crosstalk ELFEXT These tests are specified in the ANSI TIA EIA TSB 95 Bulletin The Additional Transmission Performance Guidelines for 100 Ohm 4 Pair Category 5 Cabling Note that when testing your cable installation be sure to include all patch cables between switches and end devices Adjusting Existing Category 5 Cabling to Run 1000BASE T If your existing Category 5 installation does not meet one of the test parameters for 1000BASE T there are basically three measures that can be applied to try and correct the problem 1 Replace any Category 5 patch cables with high performance Category 5e or Category 6 cables 2 Reduce the number of connectors used in the link 3 Reconnect some of the connectors in the link Fiber Standards The current TIA Telecommunications Industry Association 568 A specification on optical fiber cabling consists of one recognized cable type for horizontal subsystems and two cable types for backbone subsystems Horizontal 62 5 125 micron multimode two fibers per outlet Backbone 62 5 125 micron multimode or single mode TIA 568 B will allow the use of 50 125 micron multimode optical fiber in both the horizon
19. SMC INSTALLATION GUIDE Network TigerSwitch 10 100 Installation Guide From SMC s Tiger line of feature rich workgroup LAN solutions SMC Networks 20 Mason January 2008 Irvine CA 92618 Pub 150200065200A Phone 949 679 8000 E012008 AP RO1 Information furnished by SMC Networks Inc SMC is believed to be accurate and reliable However no responsibility is assumed by SMC for its use nor for any infringements of patents or other rights of third parties which may result from its use No license is granted by implication or otherwise under any patent or patent rights of SMC SMC reserves the right to change specifications at any time without notice Copyright 2008 by SMC Networks Inc 20 Mason Irvine CA 92618 All rights reserved Printed in Taiwan Trademarks SMC is a registered trademark and EZ Switch TigerStack and TigerSwitch are trademarks of SMC Networks Inc Other product and company names are trademarks or registered trademarks of their respective holders Compliances and Safety Warnings FCC Class A This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with
20. Wahl eines Glasfasertransceivers muB f r die Beurteilung der Gesamtsicherheit beachtet werden das die maximale Umgebungstemperatur des Transceivers f r den Betrieb nicht niedriger ist als die f r dieses Produkts Der Glasfasertransceiver mu auch ein berpr ftes Ger t der Laser Klasse 1 sein 1 Remove and keep the LC port s rubber plug When not connected to a fiber cable the rubber plug should be replaced to protect the optics 2 Check that the fiber terminators are clean You can clean the cable plugs by wiping them gently with a clean tissue or cotton ball moistened with a little ethanol Dirty fiber terminators on fiber optic cables will impair the quality of the light port transmitted through the cable and lead to degraded performance on the 3 Connect one end of the cable to the LC port on the switch and the other end to the LC port on the other device Since LC connectors are keyed the cable can be attached in only one orientation 4 4 Connectivity Rules 4 Figure 4 3 Making Fiber Port Connections 4 Asa connection is made check the Link LED on the switch corresponding to the port to be sure that the connection is valid The 1000BASE SX 1000BASE LX 1000BASE LH fiber optic ports operate at 1 Gbps full duplex with auto negotiation of flow control The maximum length for fiber optic cable operating at Gigabit speed will depend on the fiber type as listed under 1000 Mbps Gigabit Ethernet Collision Doma
21. a twisted pair cable segment to the device s RJ 45 connector gt f Figure 4 1 Making Twisted Pair Connections 2 Ifthe device is a network card and the switch is in the wiring closet attach the other end of the cable segment to a modular wall outlet that is connected to the wiring closet See the section Network Wiring Connections Otherwise attach the other end to an available port on the switch Make sure each twisted pair cable does not exceed 100 meters 328 ft in length Note Avoid using flow control on a port connected to a hub unless it is actually required to solve a problem Otherwise back pressure jamming signals may degrade overall performance for the segment attached to the hub 3 As each connection is made the Link LED on the switch corresponding to each port will light green 1000 Mbps or amber 10 100 Mbps to indicate that the connection is valid Network Wiring Connections Today the punch down block is an integral part of many of the newer equipment racks It is actually part of the patch panel Instructions for making connections in the wiring closet with this type of equipment follows 1 Attach one end of a patch cable to an available port on the switch and the other end to the patch panel 2 If not already in place attach one end of a cable segment to the back of the patch panel where the punch down block is located and the other end
22. an Continual monitoring of safety standards End of Product Life Span This product is manufactured in such a way as to allow for the recovery and disposal of all included electrical components once the product has reached the end of its life Manufacturing Materials There are no hazardous nor ozone depleting materials in this product Documentation All printed documentation for this product uses biodegradable paper that originates from sustained and managed forests The inks used in the printing process are non toxic vii viii About This Guide Purpose This guide details the hardware features of the switch including the physical and performance related characteristics and how to install the switch Audience The guide is intended for use by network administrators who are responsible for installing and setting up network equipment consequently it assumes a basic working knowledge of LANs Local Area Networks Conventions The following conventions are used throughout this guide to show information Note Emphasizes important information or calls your attention to related features or instructions Caution Alerts you to a potential hazard that could cause loss of data or damage the system or equipment Warning Alerts you to a potential hazard that could cause personal injury Related Publications The following publication gives specific information on how to operate and use the management functions of the s
23. ansparent bridging e Aggregate duplex bandwidth of up to 5 6 Gbps e Switching table with a total of 8K MAC address entries e Provides store and forward switching e Wire speed filtering and forwarding e Supports flow control using back pressure for half duplex and IEEE 802 3x for full duplex e Broadcast storm control Management e At a glance LEDs for easy troubleshooting e Network management agent Manages switch in band or out of band Supports Telnet SNMP v1 v2 RMON 4 groups and web based interface 1 5 1 Introduction Chapter 2 Network Planning Introduction to Switching A network switch allows simultaneous transmission of multiple packets via non crossbar switching This means that it can partition a network more efficiently than bridges or routers The switch has therefore been recognized as one of the most important building blocks for today s networking technology When performance bottlenecks are caused by congestion at the network access point such as the network card for a high volume file server the device experiencing congestion server power user or hub can be attached directly to a switched port And by using full duplex mode the bandwidth of the dedicated segment can be doubled to maximize throughput When networks are based on repeater hub technology the distance between end stations is limited by a maximum hop count However a switch turns the hop count back to zero So subdivid
24. be connected to this port for configuration and monitoring out of band via a null modem serial cable See Appendix B for wiring options For a detailed description of the management features refer to the Management Guide Description of Hardware 10BASE T 100BASE TX Ports The switch contains eight 10BASE T 100BASE TX Ru 45 ports All ports support automatic MDI MDI X operation so you can use straight through cables for all network connections to PCs or servers or to other switches or hubs See 10BASE T 100BASE TX Pin Assignments on page B 1 Each of these ports support auto negotiation so the optimum transmission mode half or full duplex and data rate 10 or 100 Mbps can be selected automatically If a device connected to one of these ports does not support auto negotiation the communication mode of that port can be configured manually Each port also supports IEEE 802 3x auto negotiation of flow control so the switch can automatically prevent port buffers from becoming saturated 1 2 1000BASE T SFP Ports These are combination Gigabit RJ 45 ports with shared Small Form Factor Pluggable SFP transceiver slots If an SFP transceiver purchased separately is installed in a slot and has a valid link on the port the associated RJ 45 port is disabled Description of Hardware 1 The 1000BASE T RJ 45 ports support automatic MDI MDI X operation so you can use straight through cables for all network connections to PC
25. damage this device Les raccordeurs ne sont pas utilis pour le systeme t l phonique Caution Use only twisted pair cables with RJ 45 connectors that conform to FCC standards Warnings in German Achtung Dieses Produkt enth lt keine Teile die eine Wartung vom Benutzer ben tigen Achtung Installation und Deinstallation des Ger tes m ssen von qualifiziertem Servicepersonal durchgef hrt werden Achtung Wenn das Ger t an eine Steckdose angeschlossen wird mu der Masseanschlu am dreipoligen Netzstecker mit Schutzerde verbunden werden um elektrische Gefahren zu vermeiden Achtung Dieses Ger t nutzt Laser zur Signal bertragung ber Glasfasern Die Laser entsprechen den Anforderungen an eine Lasereinrichtung der Klasse 1 und sind durch ihre Bauart im normalen Betrieb sicher f r die Augen Trotzdem sollte niemals direkt in den einen bertragungskanal geblickt werden wenn er eingeschaltet ist vi Environmental Statement The manufacturer of this product endeavours to sustain an environmentally friendly policy throughout the entire production process This is achieved though the following means Adherence to national legislation and regulations on environmental production standards Conservation of operational resources Waste reduction and safe disposal of all harmful un recyclable by products Recycling of all reusable waste content Design of products to maximize recyclables at the end of the product s life sp
26. eb dieses Ger ts erfolgt unter den SELV Bedingungen Sicherheitskleinstspannung gem IEC 60950 Diese Bedingungen sind nur gegeben wenn auch die an das Ger t angeschlossenen Ger te unter SELV Bedingungen betrieben werden Stromkabel Dies muss von dem Land in dem es benutzt wird gepr ft werden Schweiz Dieser Stromstecker muB die SEV ASE 1011Bestimmungen einhalt en Europe Das Netzkabel mu vom Typ HO3VVF3GO 75 Mindestanforderung sein und die Aufschrift lt HAR gt oder lt BASEC gt tragen Der Netzstecker mu die Norm CEE 7 7 erf llen SCHUKO Warnings and Cautionary Messages Warning This product does not contain any serviceable user parts Warning Installation and removal of the unit must be carried out by qualified personnel only Warning When connecting this device to a power outlet connect the field ground lead on the tri pole power plug to a valid earth ground line to prevent electrical hazards Warning This switch uses lasers to transmit signals over fiber optic cable The lasers are compliant with the requirements of a Class 1 Laser Product and are inherently eye safe in normal operation However you should never look directly at a transmit port when it is powered on Caution Wear an anti static wrist strap or take other suitable measures to prevent electrostatic discharge when handling this equipment Caution Do not plug a phone jack connector in the RJ 45 port This may
27. eck it read the label on the cable against the following Power Cord Set U S A and Canada The cord set must be UL approved and CSA certified The minimum specifications for the flexible cord are No 18 AWG not longer than 2 meters or 16 AWG Type SV or SJ 3 conductor The cord set must have a rated current capacity of at least 10 A The attachment plug must be an earth grounding type with NEMA 5 15P 15 A 125 V or NEMA 6 15P 15 A 250 V configuration Denmark The supply plug must comply with Section 107 2 D1 Standard DK2 1a or DK2 5a Switzerland The supply plug must comply with SEV ASE 1011 U K The supply plug must comply with BS1363 3 pin 13 A and be fitted with a 5 A fuse which complies with BS1362 The mains cord must be lt HAR gt or lt BASEC gt marked and be of type HO3VVF3G0 75 minimum Europe The supply plug must comply with CEE7 7 SCHUKO The mains cord must be lt HAR gt or lt BASEC gt marked and be of type HO3VVF3G0 75 minimum IEC 320 receptacle Veuillez lire fond l information de la s curit suivante avant d installer le Switch AVERTISSEMENT L installation et la d pose de ce groupe doivent tre confi s un personnel qualifi e Ne branchez pas votre appareil sur une prise secteur alimentation lectrique lorsqu il n y a pas de connexion de mise la terre mise la masse e Vous devez raccorder ce g
28. in on page 4 6 Connectivity Rules When adding hubs repeaters to your network please follow the connectivity rules listed in the manuals for these products However note that because switches break up the path for connected devices into separate collision domains you should not include the switch or connected cabling in your calculations for cascade length involving other devices 1000BASE T Cable Requirements All Category 5 UTP cables that are used for 100BASE TX connections should also work for 1000BASE T providing that all four wire pairs are connected However it is recommended that for all critical connections or any new cable installations Category 5e enhanced Category 5 or Category 6 cable should be used The Category 5e and 6 specifications include test parameters that are only recommendations for Category 5 Therefore the first step in preparing existing Category 5 cabling for running 1000BASE T is a simple test of the cable installation to be sure that it complies with the IEEE 802 3 2005 standards 4 5 4 Making Network Connections 1000 Mbps Gigabit Ethernet Collision Domain Table 4 1 Maximum 1000BASE T Gigabit Ethernet Cable Length Cable Type Maximum Cable Length Connector Category 5 5e or 6 100 ohm UTP or STP 100 m 328 ft RJ 45 Table 4 2 Maximum 1000BASE SX Gigabit Ethernet Cable Lengths Fiber Size Fiber Bandwidth Maximum Cable Length Con
29. ing the network into smaller and more manageable segments and linking them to the larger network by means of a switch removes this limitation A switch can be easily configured in any Ethernet Fast Ethernet or Gigabit Ethernet network to significantly boost bandwidth while using conventional cabling and network cards 2 1 2 Network Planning Application Examples The switch is not only designed to segment your network but also to provide a wide range of options in setting up network connections Some typical applications are described below Collapsed Backbone The switch is an excellent choice for mixed Ethernet Fast Ethernet and Gigabit Ethernet installations where significant growth is expected in the near future You can easily build on this basic configuration adding direct full duplex connections to workstations or servers When the time comes for further expansion just connect to another hub or switch using one of the Fast Ethernet ports built into the front panel or a Gigabit Ethernet port on a plug in SFP transceiver In the figure below the switch is operating as a collapsed backbone for a small LAN It is providing dedicated 10 Mbps full duplex connections to workstations 100 Mbps full duplex connections to power users and 1 Gbps full duplex connections to servers Servers Workstations Workstations 1 Gbps 100 Mbps 10 Mbps Full Duplex Full Duplex Full Duplex Figure 2
30. l implementations of your network follow these guidelines e Clearly label the opposing ends of each cable e Using your building s floor plans draw a map of the location of all network connected equipment For each piece of equipment identify the devices to which it is connected e Note the length of each cable and the maximum cable length supported by the switch ports e For ease of understanding use a location based key when assigning prefixes to your cable labeling Use sequential numbers for cables that originate from the same equipment e Differentiate between racks by naming accordingly e Label each separate piece of equipment e Display a copy of your equipment map including keys to all abbreviations at each equipment rack 4 7 4 Making Network Connections 4 8 Appendix A Troubleshooting Diagnosing Switch Indicators Table A 1 Troubleshooting Chart Symptom Action Power LED is Off Check connections between the switch the power cord and the wall outlet Contact your dealer for assistance Diag LED is Amber e Power cycle the switch to try and clear the condition Ifthe condition does not clear contact your dealer for assistance Link LED is Off e Verify that the switch and attached device are powered on Besure the cable is plugged into both the switch and corresponding device e Ifthe switch is installed in a rack check the connections to the punch down block and patch panel
31. nd No other pins are used The serial port s configuration requirements are as follows Default Baud rate 9 600 bps e Character Size 8 Characters e Parity None e Stop bit One Data bits 8 Flow control none 3 7 3 Installing the Switch 3 8 Chapter 4 Making Network Connections Connecting Network Devices The switch is designed to be connected to 10 or 100 Mbps network cards in PCs and servers as well as to other switches and hubs It may also be connected to remote devices using optional 1000BASE SX 1000BASE LX or 1000BASE LH SFP transceivers Twisted Pair Devices Each device requires an unshielded twisted pair UTP cable with RJ 45 connectors at both ends Use Category 5 5e or 6 cable for 1000BASE T connections Category 5 or better for 100BASE TX connections and Category 3 or better for 10BASE T connections Cabling Guidelines The RJ 45 ports on the switch support automatic MDI MDI X pinout configuration so you can use standard straight through twisted pair cables to connect to any other network device PCs servers switches routers or hubs See Appendix B for further information on cabling Caution Do not plug a phone jack connector into an RJ 45 port This will damage the switch Use only twisted pair cables with RJ 45 connectors that conform to FCC standards 4 1 4 Making Network Connections Connecting to PCs Servers Hubs and Switches 1 Attach one end of
32. nector 62 5 125 micron 160 MHz km 2 220 m 7 722 ft LC multimod ter 200 MHz km 2 275 m 7 902 fi LC 50 125 micron multimode 400 MHz km 2 500 m 7 1641 ft LC fiber 500 MHz km 2 550 m 7 1805 ft LC Table 4 3 Maximum 1000BASE LX Gigabit Ethernet Cable Length Fiber Size Fiber Bandwidth Maximum Cable Length Connector 9 125 micron N A 2m 5km 7ft 3 2 miles LC single mode fiber Table 4 4 Maximum 1000BASE LH Gigabit Ethernet Cable Length Fiber Size Fiber Bandwidth Maximum Cable Length Connector 9 125 micron N A 2m 70km LC single mode fiber 7 ft 43 5 miles 100 Mbps Fast Ethernet Collision Domain Table 4 5 Maximum Fast Ethernet Cable Lengths Type Cable Type Max Cable Length Connector 100BASE TX Category 5 or better 100 ohm UTP or STP 100 m 328 ft RJ 45 10 Mbps Ethernet Collision Domain Table 4 6 Maximum Ethernet Cable Length Type Cable Type Max Cable Length Connector 10BASE T Category 3 or better 100 ohm UTP 100 m 328 ft RJ 45 4 6 Cable Labeling and Connection Records 4 Cable Labeling and Connection Records When planning a network installation it is essential to label the opposing ends of cables and to record where each cable is connected Doing so will enable you to easily locate inter connected devices isolate faults and change your topology without need for unnecessary time consumption To best manage the physica
33. nity to conducted disturbances Induced by radio frequency fields EN 61000 4 6 1996 0 15 80 MHz with 1 kHz AM 80 Modulation 3 V m Power frequency magnetic field immunity test according to EN 61000 4 8 1993 1 A m at frequency 50 Hz Voltage dips short interruptions and voltage variations immunity test according to EN 61000 4 11 1994 gt 95 Reduction 10 ms 30 Reduction 500 ms gt 95 Reduction 5000 ms LVD e EN 60950 1 2001 _ Caution Do not plug a phone jack connector in the RJ 45 port This may damage this device Attention Les raccordeurs ne sont pas utilis s pour le syst me t l phonique Safety Compliance Warning Fiber Optic Port Safety When using a fiber optic port never look at the transmit laser while it is powered on Also never look directly at the fiber TX port and fiber cable LASER DEVICE ends when they are powered on Avertissment Ports pour fibres optiques s curit sur le plan optique Ne regardez jamais le laser tant qu il est sous tension Ne regardez jamais directement le port TX Transmission fibres optiques et les embouts de c bles fibres optiques tant qu ils sont sous tension Warnhinweis Faseroptikanschl sse Optische Sicherheit Niemals ein Ubertragungslaser betrachten w hrend dieses LASERGERAT eingeschaltet ist Niemals direkt auf den Faser TX AnschluB DER KLASSE und auf die Faserkabelenden schauen w hrend diese eingeschaltet sind PSE Alarm
34. ohm Category 5 or better cable for 100 Mbps connections Also be sure that the length of any twisted pair connection does not exceed 100 meters 328 feet The RJ 45 ports on the switch base unit support automatic MDI MDI X operation so you can use straight through cables for all network connections to PCs or servers or to other switches or hubs In straight through cable pins 1 2 3 and 6 at one end of the cable are connected straight through to pins 1 2 3 and 6 at the other end of the cable When using any RJ 45 port on this switch you can use either straight through or crossover cable B 1 B Cables Table B 1 10 100BASE TX MDI and MDI X Port Pinouts Pin MDI Signal Name MDI X Signal Name 1 Transmit Data plus TD Receive Data plus RD 2 Transmit Data minus TD Receive Data minus RD 3 Receive Data plus RD Transmit Data plus TD 6 Receive Data minus RD Transmit Data minus TD 4 5 7 8 Notused Not used Note The and signs represent the polarity of the wires that make up each wire pair Straight Through Wiring If the twisted pair cable is to join two ports and only one of the ports has an internal crossover MDI X the two pairs of wires must be straight through When auto negotiation is enabled for any RJ 45 port on this switch you can use either straight through or crossover cable to connect to any device type You must connect all four wire pairs as shown in
35. ork connections to PCs or servers or to other switches or hubs The table below shows the 1000BASE T MDI and MDI X port pinouts These ports require that all four pairs of wires be connected Note that for 1000BASE T operation all four pairs of wires are used for both transmit and receive Use 100 ohm Category 5 5e or 6 unshielded twisted pair UTP or shielded twisted pair STP cable for 1000BASE T connections Also be sure that the length of any twisted pair connection does not exceed 100 meters 328 feet Table B 2 1000BASE T MDI and MDI X Port Pinouts Pin MDI Signal Name MDI X Signal Name 1 Bi directional Data One Plus BI_D1 Bi directional Data Two Plus BI_D2 2 Bi directional Data One Minus BI_D1 Bi directional Data Two Minus BI_D2 3 Bi directional Data Two Plus BI_D2 Bi directional Data One Plus BI_D1 4 Bi directional Data Three Plus BI_D3 Bi directional Data Four Plus BI_D4 B 3 B Cables Table B 2 1000BASE T MDI and MDI X Port Pinouts Pin MDI Signal Name MDI X Signal Name 5 Bi directional Data Three Minus BI_D3 Bi directional Data Four Minus BI_D4 6 Bi directional Data Two Minus BI_D2 Bi directional Data One Minus BI_D1 1 Bi directional Data Four Plus BI_D4 Bi directional Data Three Plus BI_D3 8 Bi directional Data Four Minus BI_D4 Bi directional Data Three Minus BI_D3 Cable Testing for Existing Category 5 Cable
36. ou are connecting to the switch has not been disabled If it has not been disabled then check the network cabling that runs between your remote location and the switch Note The management agent accepts up to four simultaneous Telnet sessions If the maximum number of sessions already exists an additional Telnet connection will not be able to log into the system A 2 Appendix B Cables Twisted Pair Cable and Pin Assignments For 10 100BASE TX connections the twisted pair cable must have two pairs of wires For 1000BASE T connections the twisted pair cable must have four pairs of wires Each wire pair is identified by two different colors For example one wire might be green and the other green with white stripes Also an RJ 45 connector must be attached to both ends of the cable Caution DO NOT plug a phone jack connector into any RJ 45 port Use only twisted pair cables with RJ 45 connectors that conform with FCC standards Caution Each wire pair must be attached to the RJ 45 connectors in a specific orientation The figure below illustrates how the pins on the RJ 45 connector are numbered Be sure to hold the connectors in the same orientation when attaching the wires to the pins Figure B 1 RJ 45 Connector Pin Numbers 10BASE T 100BASE TX Pin Assignments Use unshielded twisted pair UTP or shielded twisted pair STP cable for RJ 45 connections 100 ohm Category 3 or better cable for 10 Mbps connections or 100
37. rea Only MIC Notice Republic of Korea Only MIC Class A gt geen AR 717 URS 32847171 MIC Geen DEET TTT QU Salat E AIS R o Jg F 7 tejoj 21e BEEN SE PPAR Mois Lass DESHMI sch CE Mark Declaration of Conformance for EMI and Safety EEC This information technology equipment complies with the requirements of the Council Directive 89 336 EEC on the Approximation of the laws of the Member States relating to Electromagnetic Compatibility and 73 23 EEC for electrical equipment used within certain voltage limits and the Amendment Directive 93 68 EEC For the evaluation of the compliance with these Directives the following standards were applied RFI Emission Limit class A according to EN 55022 1998 e Limit class A for harmonic current emission according to EN 61000 3 2 1995 e Limitation of voltage fluctuation and flicker in low voltage supply system according to EN 61000 3 3 1995 Immunity e Product family standard according to EN 55024 1998 e Electrostatic Discharge according to EN 61000 4 2 1995 Contact Discharge 4 kV Air Discharge 8 kV e Radio frequency electromagnetic field according to EN 61000 4 3 1996 80 1000 MHz with 1 kHz AM 80 Modulation 3 V m e Electrical fast transient burst according to EN 61000 4 4 1995 AC DC power supply 1 kV Data Signal lines 0 5 kV e Surge immunity test according to EN 61000 4 5 1995 AC DC Line to Line 1 kV AC DC Line to Earth 2 kV e Immu
38. roupe une sortie mise la terre mise la masse afin de respecter les normes internationales de s curit e Le coupleur d appareil le connecteur du groupe et non pas la prise murale doit respecter une configuration qui permet un branchement sur une entr e d appareil EN 60320 IEC 320 e La prise secteur doit se trouver proximit de l appareil et son acc s doit tre facile Vous ne pouvez mettre l appareil hors circuit qu en d branchant son cordon lectrique au niveau de cette prise e L appareil fonctionne une tension extr mement basse de s curit qui est conforme la norme IEC 60950 Ces conditions ne sont maintenues que si l quipement auquel il est raccord fonctionne dans les m mes conditions France et P rou uniquement Ce groupe ne peut pas tre aliment par un dispositif imp dance la terre Si vos alimentations sont du type imp dance la terre ce groupe doit tre aliment par une tension de 230 V 2 P T par le biais d un transformateur d isolement rapport 1 1 avec un point secondaire de connexion portant l appellation Neutre et avec raccordement direct la terre masse Cordon lectrique Il doit tre agr dans le pays d utilisation Etats Unis et Le cordon doit avoir re u I homologation des UL et un certificat de la Canada CSA Les sp cifications minimales pour un cable flexible sont AWG No 18 ouAWG No 16 pour un cable de longueur inf rieure 2 m tres
39. s of 50 125 62 5 125 micron or 9 125 micron core fiber cable 100BASE TX IEEE 802 3u specification for 100 Mbps Ethernet over two pairs of Category 5 UTP cable 1000BASE LX IEEE 802 3z specification for Gigabit Ethernet over two strands of 50 125 62 5 125 or 9 125 micron core fiber cable 1000BASE LH Specification for long haul Gigabit Ethernet over two strands of 9 125 micron core fiber cable 1000BASE SX IEEE 802 3z specification for Gigabit Ethernet over two strands of 50 125 or 62 5 125 micron core fiber cable 1000BASE T IEEE 802 3ab specification for Gigabit Ethernet over 100 ohm Category 5 5e or 6 twisted pair cable using all four wire pairs Auto Negotiation Signalling method allowing each node to select its optimum operational mode e g speed and duplex mode based on the capabilities of the node to which it is connected Bandwidth The difference between the highest and lowest frequencies available for network signals Also synonymous with wire speed the actual speed of the data transmission along the cable Glossary 1 Glossary Collision A condition in which packets transmitted over the cable interfere with each other Their interference makes both signals unintelligible Collision Domain Single CSMA CD LAN segment CSMA CD CSMA CD Carrier Sense Multiple Access Collision Detect is the communication method employed by Ethernet Fast Ethernet and Gigabit Ethernet End Station
40. s or servers or to other switches or hubs See 1000BASE T Pin Assignments on page B 3 Port and System Status LEDs The switch includes a display panel for key system and port indications that simplify installation and network troubleshooting The LEDs which are located on the front panel for easy viewing are shown below and described in the following tables System Status LEDs Port Status LEDs d SMC Networks TigerSwitch 10 100 SMC6110L2 0105 1 0206 Power 3 O7 O9 Dig 408 O10 Console errs Figure 1 2 Port LEDs Table 1 1 Port Status LEDs LED Condition Status Fast Ethernet Ports Ports 1 8 Link Activity On Flashing Porthas established a valid 10 Mbps network connection Amber Flashing indicates activity On Flashing Porthas established a valid 100 Mbps network connection Green Flashing indicates activity Off There is no valid link on the port Gigabit Ethernet Ports Ports 9 10 Link Activity On Flashing Porthas established a valid 10 100 Mbps network connection Amber Flashing indicates activity On Flashing Porthas established a valid 1000 Mbps network connection Green Flashing indicates activity Off There is no valid link on the port 1 3 1 Introduction Table 1 2 System Status LEDs LED Condition Status PWR On Green The units internal power supply is operating
41. tal and backbone in addition to the types listed above All optical fiber components and installation practices must meet applicable building and safety codes B 4 Appendix C Specifications Physical Characteristics Ports 8 10 100BASE TX with auto negotiation 2 10 100 1000BASE T shared with two SFP transceiver slots Network Interface Ports 1 10 RJ 45 connector auto MDI X 10BASE T RJ 45 100 ohm UTP cable Category 3 or better 100BASE TX RJ 45 100 ohm UTP cable Category 5 or better 1000BASE T RJ 45 100 ohm UTP or STP cable Category 5 5e or 6 Maximum Cable Length 100 m 328 ft Buffer Architecture 2 Mbits Aggregate Bandwidth 5 6 Gbps Switching Database 8K MAC address entries LEDs System Power Diag Diagnostic Port status link speed and activity Weight 1 8 kg 3 97 lbs Size 33 0 x 20 4 x 4 3 cm 12 99 x 8 03 x 1 73 in Temperature Operating 0 C to 50 C 32 F to 122 F Storage 40 C to 70 C 40 F to 158 F Humidity Operating 10 to 90 non condensing Cl IC Specifications AC Input 100 to 240 V 50 60 Hz 0 4A Power Supply Internal auto ranging transformer 100 to 240 VAC 50 to 60 Hz Power Consumption 13 2 Watts maximum Maximum Current 0 4 A 100 VAC 0 2 A 240 VAC Switch Features Forwarding Mode Store and forward Throughput Wire speed Flow Control Full Duplex IEEE 802 3x Half Duplex Back pressure Management Features
42. the following diagram to support Gigabit Ethernet EIA TIA 568B RJ 45 Wiring Standard 10 100BASE TX Straight through Cable White Orange Stripe Yi Orange N White Green Stripe Blue End A End B White Blue Stripe Green White Brown Stripe Brown Figure B 2 Straight through Wiring JT B 2 Twisted Pair Cable and Pin Assignments B Crossover Wiring If the twisted pair cable is to join two ports and either both ports are labeled with an X MDI X or neither port is labeled with an X MDI a crossover must be implemented in the wiring When auto negotiation is enabled for any RJ 45 port on this switch you can use either straight through or crossover cable to connect to any device type You must connect all four wire pairs as shown in the following diagram to support Gigabit Ethernet EIA TIA 568B RJ 45 Wiring Standard 10 100BASE TX Crossover Cable White Orange Stripe 1 White Green Stripe 1 End A LE 2 2 na End B ZT Blue TK 3 3 a 4 D 5 White Blue Stripe 5 gt lt I Green IG 2 Sg 8 8 White Brown Stripe Brown Figure B 3 Crossover Wiring 1000BASE T Pin Assignments All 1000BASE T ports support automatic MDI MDI X operation so you can use straight through cables for all netw
43. tic SFP Devices Connectivity Rules 1000BASE T Cable Requirements 1000 Mbps Gigabit Ethernet Collision Domain 100 Mbps Fast Ethernet Collision Domain 10 Mbps Ethernet Collision Domain Cable Labeling and Connection Records Appendix A Troubleshooting A 1 Diagnosing Switch Indicators Power and Cooling Problems Installation In Band Access Appendix B Cables B 1 Twisted Pair Cable and Pin Assignments 10BASE T 100BASE TX Pin Assignments Straight Through Wiring Crossover Wiring 1000BASE T Pin Assignments Fiber Standards Appendix C Specifications C 1 Switch Features Management Features Standards Compliances Appendix D Ordering Information Glossary Index xii 4 1 4 1 4 1 4 2 4 2 4 4 4 5 4 5 4 6 4 6 4 7 A 1 A 1 A 2 B 1 B 2 B 3 B 4 C 2 C 2 C 3 D 1 Tables Table 1 1 Table 1 2 Table 3 1 Table 4 1 Table 4 2 Table 4 3 Table 4 4 Table 4 5 Table 4 6 Table A 1 Table B 1 Table B 2 Port Status LEDs System Status LEDs Serial Cable Wiring Maximum 1000BASE T Gigabit Ethernet Cable Length Maximum 1000BASE SX Gigabit Ethernet Cable Lengths Maximum 1000BASE LX Gigabit Ethernet Cable Length Maximum 1000BASE LH Gigabit Ethernet Cable Length Maximum Fast Ethernet Cable Lengths Maximum Ethernet Cable Length Troubleshooting Chart 10 100BASE TX MDI and MDI X Port Pinouts 1000BASE T MDI and MDI X Port Pinouts 1 3 1 4 4 6 4 6 4 6 4 6 A 1 B 2 xiii Figures
44. tion tech_support_drivers_downloads World Wide Web http www smc com 150200065200A R01 20 Mason Irvine CA 92618 Phn 949 679 8000 e www smc com
45. to a modular wall outlet 4 2 3 Twisted Pair Devices 4 Label the cables to simplify future troubleshooting See Cable Labeling and Connection Records on page 4 7 Switch Equipment Rack side view N x A Punch Down Block NV Patch Panel Figure 4 2 Network Wiring Connections 4 3 4 Making Network Connections Fiber Optic SFP Devices An optional Gigabit SFP transceiver 1000BASE SX 1000BASE LX or 1000BASE LH can be used for a backbone connection between switches or for connecting to a high speed server Each single mode fiber port requires 9 125 micron single mode fiber optic cable with an LC connector at both ends Each multimode fiber optic port requires 50 125 or 62 5 125 Warning Warning Hinweis micron multimode fiber optic cabling with an LC connector at both ends This switch uses lasers to transmit signals over fiber optic cable The lasers are compliant with the requirements of a Class 1 Laser Product and are inherently eye safe in normal operation However you should never look directly at a transmit port when it is powered on When selecting a fiber SFP device considering safety please make sure that it can function at a temperature that is not less than the recommended maximum operational temperature of the product You must also use an approved Laser Class 1 SFP transceiver Bei der
46. unting 3 5 device connections 4 1 E electrical interference avoiding 3 1 equipment checklist 3 2 Ethernet connectivity rules 4 6 F Fast Ethernet connectivity rules 4 6 features C 2 management 1 5 switch 1 5 fiber cables 4 4 flow control IEEE 802 3x 1 2 front panel of switch 1 1 full duplex connectivity 2 1 G Gigabit Ethernet cable lengths 4 6 grounding for racks 3 3 I IEEE 802 3x flow control 1 2 indicators LED 1 3 installation connecting devices to the switch 4 2 desktop or shelf mounting 3 5 network wiring connections 4 2 port connections 4 1 4 4 power requirements 3 1 problems A 2 rack mounting 3 3 Index 1 E site requirements 3 1 L laser safety 4 4 LC port connections 4 4 LED indicators Diag 1 4 Power 1 4 problems A 1 location requirements 3 1 M management agent 1 2 features 1 5 C 2 out of band 1 2 SNMP 1 2 web based 1 2 modules 100BASE FX C 3 mounting the switch inarack 3 3 on a desktop or shelf 3 5 multimode fiber optic cables 4 4 N network connections 4 1 4 4 examples 2 2 0 out of band management 1 2 P package contents 3 2 pin assignments B 1 1000BASE T B 3 10BASE T 100BASE TX B 1 console port 3 7 DB 9 3 7 port saturation 1 2 ports connecting to 4 1 4 4 power connecting to 3 7 problems troubleshooting A 1 Index 2 R rack mounting 3 3 rear panel of switch 1 1 rear panel receptacles 1 4 RJ 45 port 1 2 1 3
47. ving a transceiver Note SFP transceivers are not provided in the switch package Connecting to a Power Source To connect a switch to a power source 1 3 6 Insert the power cable plug directly into the AC socket located at the back of the switch 100 240V 50 60Hz 0 4A Figure 3 6 Power Socket Plug the other end of the cable into a grounded three pin AC power source Note For International use you may need to change the AC line cord You must use a line cord set that has been approved for the receptacle type in your country Check the front panel LEDs as the device is powered on to be sure the Power LED is lit If not check that the power cable is correctly plugged in Connecting to the Console Port 3 Connecting to the Console Port The DB 9 serial port on the switch s back panel is used to connect to the switch for out of band console configuration The command line driven configuration program can be accessed from a terminal or a PC running a terminal emulation program The pin assignments used to connect to the serial port are provided in the following table Figure 3 7 Serial Port DB 9 DTE Pin Out Wiring Map for Serial Cable Table 3 1 Serial Cable Wiring Null Modem Switch s 9 Pin Serial Port PC s 9 Pin DTE Port 2RXD receive data 3 TXD transmit data 3 TXD transmit data 2 RXD receive data 5 SGND signal ground 5 SGND signal grou
48. witch The Management Guide Also as part of the switch s software there is an online web based help that describes all management related features Revision History This section summarizes the changes in each revision of this guide January 2008 Revision This is the first revision of this guide Contents Chapter 1 Introduction Overview Switch Architecture Network Management Options Description of Hardware 10BASE T 100BASE TX Ports 1000BASE T SFP Ports Port and System Status LEDs Power Supply Socket Features and Benefits Connectivity Expandability Performance Management Chapter 2 Network Planning Introduction to Switching Application Examples Collapsed Backbone Network Edge Deployment Application Notes AAGAKRARWBONNDYN A CR Cees Crees Cree Ces Ceres Canes Crees Cure Cares Ces Cs D NO Ro P wech E D D N A Chapter 3 Installing the Switch Selecting a Site Ethernet Cabling Equipment Checklist Package Contents Optional Rack Mounting Equipment Mounting Rack Mounting Desktop or Shelf Mounting Installing an Optional SFP Transceiver Connecting to a Power Source Connecting to the Console Port Wiring Map for Serial Cable 3 1 3 1 3 2 3 2 3 3 3 5 3 5 3 6 3 7 xi Contents Chapter 4 Making Network Connections Connecting Network Devices Twisted Pair Devices Cabling Guidelines Connecting to PCs Servers Hubs and Switches Network Wiring Connections Fiber Op
Download Pdf Manuals
Related Search