Philips 27HT7210D 27" real flat commercial TV
Contents
1. CABLE ANTENNA Applicable to 279740000127 only REMOTE CONTROLS The following remote controls are applicable to Philips Business Display Solutions TV products These can be used for setup and configuration purposes 9 9 Slide this button up to enter into Guest mode Slide this side button down to enter into Setup mode Y 90 90 90000 2 o V 1 5 RC2888 01 Guest Mode Remote RC2573GR optional RC2573GR optional RC2573GR is an optional remote control for Institutional TV Business Display Solutions features and SmartCard settings It be purchased separately Refer to this document for details of its functions When in setup mode press RECALL on the RC2573GR remote control i 1 LO6HUI 1 1 Youll see and an information screen that describes the TV chassis firmware version diagnostic codes 3 CODE 0 0 0 setup information and other service and technical 4 OP 34 4 161 9 data regarding the TV s configuration 6 7 Line 11 indicates whether the is in CONSUMER 5 Se COMMERCIAL mode and whether it is on line VL 6 with a SmartPort DCM such as a CLON99BK BS 31 TR 31 SmartLoader Net1Card or Net01SC SmartCard CHANNEL For more information refer to the service documentation for the ITV BDS LO6 TV Chassis GUEST REMOTE CONTROL KEYS CH Guide Source Selec2. DIMENSIONS c eh 1 55 Oe ine Seir e EHE 21 Appendix Glossary Definitions Acronyms Abbreviations 22 23 Cleaning Sc Gare as2cc224e5 be te eee net ede eee one oor __ _ 24 ae G 24 Litt ed Warranty oso ues xau ESTRENA 24 hu rrr 25 Note Specifications in this manual are subject to change without notification es Recycling Directive To minimize harm to the environment the batteries supplied with the TV 67 set do not contain mercury or nickel cadmium If possible when disposing of batteries use recycling means available to you Your TV set uses materials which are reusable or which can be recycled To minimize the amount of waste in the environment certain companies recover used sets for dismantling and collection of reusable materials contact your dealer or local recycling resources oe SEP peo 10 11 12 13 14 15 16 IMPORTANT SAFETY INSTRUCTIONS Read before operating equipment Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with a dry cloth Do not block any of the ventilation openings Install in accordance with the manufacturers instructions Do not install near any heat sources such as radiators heat re
3. product that requires modification or adaptation to enable it to operate in any country other than the country for which it was designed manufactured approved and or authorized or repair of products damaged by these modifications incidental or consequential damages resulting from the product Some states do not allow the exclusion of incidental or consequen tial damages so the above exclusion may not apply to you This includes but is not limited to prerecorded material whether copy righted or not copyrighted WHERE IS SERVICE AVAILABLE Warranty service is available in all countries where the product is offi cially distributed by Philips Consumer Electronics Company In coun tries where Philips Consumer Electronics Company does not distribute the product the local Philips service organization will attempt to pro vide service although there may be a delay if the appropriate spare parts and technical manual s are not readily available MAKE SURE YOU KEEP Please keep your sales receipt or other document showing proof of pur chase Attach it to this owner s manual and keep both nearby Also keep the original box and packing material in case you need to return your product BEFORE REQUESTING SERVICE Please check your owner s manual before requesting service Adjustments of the controls discussed there may save you a service call TO GET WARRANTY SERVICE IN U S A PUERTO RICO OR U S VIRGIN ISLANDS Contact
4. OFF TV screen displays snow and the audio appears as white noise static BLACK TV screen display is black and the audio is muted BLUE TV screen display is blue and the audio is muted e AUDIO VIDEO OUT MUTE NO YES When set to YES it turns off the audio and video MONITOR OUT signals either demodulated RF input or loop through video Intended to prevent recording of pay per view content e MONITOR OUT RF NO YES This feature configures the audio and video monitor outputs provided the AUDIO VIDEO OUT MUTE is not set to YES NO The signals that are present at the monitor outputs are the same as those of the currently selected channels or video input The monitor outputs track what is viewed and heard on the TV TES Regardless of the current selected TV source eg AV2 S VIDEO input the signal present at the monitor outputs is always the tuner output see NOTE below Note When The MONITOR OUT RF is initially changed from its current setting the monitor out signal depends upon the previous MONITOR OUT setting until a different TV source is selected From then on the new MONITOR OUT setting will perform as described 15 TV SETUP MENU amp SUB MENUS CONTINUED e WELCOME MESSAGE gt A welcome message maximum of 20 characters 2 lines can be programmed to appear on the TV screen when the TV is powered on The message remains on the screen until any button on the TV front panel or remote
5. PMT which is stored as channel number Major dot Minor eg 2 1 in the TV set The virtual channels will not be used in this case If USE CHANNEL TABLE is set to YES Program and System Information Protocol PSIP is used during channel installation and Direct Channel Command The digital tuner will use the virtual channel information that is contained in the PSIP to map the virtual channels to the physical channels which is also called Major dot Minor channel in this case For more information on the PSIP you can refer to ATSC Standard Program and System information Protocol for Terrestrial Broadcast and Cable Revision B which can be found at the website http www atsc org standards a 65b pdf e DIGITAL TV LABEL NO YES If DIGITAL TV LABEL is set to NO The Digital TV channel number will not be displayed on the screen If DIGITAL TV LABEL is set to YES The Digital TV channel number will be displayed on the top right hand corner of the TV screen for about 5 seconds whenever there is a change in digital TV channel For the changes in the Digital TV label to take effect please conduct a cold warm start when the setting is changed from Yes to No vice versa DTV SETUP Entering the DTV SETUP menu allows you to edit features while you are in Digital TV mode CHANNEL EDIT Channel edit allows you to add or skip channels from your favorite list be skipped when scrolling channels with the or CH If Added is selected the
6. 12 LOCK KEYBOARD 15 M MAX VOLUME 15 MIN VOLUME 15 MONITOR OUT RF 1 15 25 MOVIE PADINIGIS V eR rar dea d 18 MUTE AUDIO 7 VIDEO siib ck SHE Uo SS 15 N OF CHANNELS TV SETUP REUNIR n 12 NOISE REDUCTION SETUP MENU ITEM uiro e en 14 Me lj nnn 15 R GUEST REMOTE aur dd ERU D reote Pen trn 8 RC2SZSGR SETUP REMOTE 455r om 04 0 sue en set hae sue 8 RECALL SETUP REMOTE COMMAND 5 8 RECYCLING BATTERIES Rene Year T er ees 2 V Sun de oem 2 REMINDER siers soeurs EC POVERI TS 17 REMOTE CONTROLS 120544520804 cime 04865 eie eor eoi bebes 8 S SAFETY INFORMATION s mes mmm SER m ORE S 4 SAP SECOND AUDIO PROGRAM 14 DAVE T M 17 SAY ED VGH PR HEROUM SEE REDDERET 18 SCREEN COLOR NON UNIFORMITY 4 SECURITY ae Gis deu eu 19 STII Be gooey aye as ay og Ge eser pe eee 14 SLEEPTIMER oorr code oe 19 SOUND MODE sirri rer ine N E dederit D ROLE 14 SOURCE MENU ITEM Or t obe erae 17 SPEAKER TIU TE T
7. REMOTE CONTROL RC2888 01 only when SECURITY in the TV SETUP MENU is set to STANDARD Refer to page 18 To activate TV SETUP MENU 1 Select a channel number Key in 3 1 9 7 5 3 followed by the 6 button the remote control Note All buttons in step 2 on the remote control 3 19 7 5 3 must be pressed successively within 20 seconds or else the TV Setup Menu will not be activated WITH REMOTE CONTROL RC2573GR only in TV Commercial Mode PART To check the TV s mode 1 Set the remote control selectable switch to SETUP 2 Press RECALL key on the remote control The TV Status menu will appear 3 Check line 11 of the menu to see if the TV is in the Commercial or Consumer mode If the TV is in Commercial mode proceed to Part B to activate the TV Setup menu Otherwise follow the sets in Part C to change the TV mode to Commercial PART B To activate TV Setup Menu 1 Press the M button on the remote control to activate the TV Setup Menu PART To select Commercial mode if the TV is in Consumer mode or to select Consumer mode if the TV is in Commerical mode 1 Press 0 2 4 9 9 5 followed by the M button on the remote control The TV Setup Menu screen will appear Press 4 gt to select Commercial if you are in Consumer Mode but wish to switch to Commercial Mode Select Consumer if you are in Commercial mode but wish to switch to Consumer Mode Press v followed by to store your settings Highlight STORE and p
8. Televisions for specialized Setup Mode and or restricted features such as front panel lockout volume range channel list etc SmartPort Philips proprietary three wire synchronous serial Communications and control interface SmartPlug See SmartPort Socket Connector on a cable that connects to socket SBB Set back box Used interchangeably with set top box General term for a device that adds functionality to and or interfaces a television with a host content and or control environment STB Set top box See SBB Generally referred to as off A state of operation characterized by relatively low power consumption Standby in which the unit television is connected to an AC power source but not in active use and capable of responding to queries or commands from a control device and or DCM eyecare First data word of a Philips RC 5 RC 6 remote control code for standard television commands Synonymous with Business Display Solutions guest mode First data word of a Philips RC 5 RC 6 remote control code reserved for specialized commands Used System 7 for Business Display Solutions ITV setup mode TCP IP Transmission Control Protocol Internet Protocol De facto standard protocol for Internet communications UDP User Datagram Protocol A minimal message oriented transport layer protocol that is currently documented in IETF RFC 768 Used by Philips NetLin
9. an alternate channel A CH command from the remote control the TV will tune to the next signal source eg tuner AV2 S VIDEO etc in the channel ring NO Upon receiving an alternate channel A CH command from the remote control the TV will switch to the most recently selected channel input e CS1 CS2 CS3 CS4 CS5 CS6 CC1 CC2 4 OFF MUTE for digital channels CC 1 CC 2 OFF CC ON MUTE for analog channels Since July 1993 TV sets with 13 screens or larger must have built in caption decoders Captioning of most broadcast and cablecast programming is mandated under the Telecommunications Act of 1996 except for programs exempted by the FCC For additional information please visit U S FCC website at http www fcc gov cgb consumerfacts closedcaption html OFF Close captioning text will not be displayed even when it is provided by the broadcaster MUTE or CC ON MUTE Close captioning text will appear only when the TV is MUTED CS1 CS2 CS3 C54 CS5 CS6 CC1 CC2 CC4 CC 1 2 Close captioning text will be displayed if it is present in the incoming signal e SAVE CC NO YES This feature enables the CC setting see CC to remain in effect after the TV is powered down NO When the TV is powered down and turned on again the closed captioning settings will default to OFF YES When the TV is powered down and turned on again the closed captioning previously set will remain in effect
10. been selected To deselect press A or v where the X is The X will disappear indicating that the TV Rating has bee deactivated VIEW MOVIE RATINGS VIEW To select Movie Ratings highlight MOVIE RATINGS and press cursor VIEW 1 gt on the remote control to invoke the Movie Ratings sub menu VIEW VIEW Press cursor or 4 on the remote control to toggle between View BLOCKED and Blocked BLOCKED gt Movie Ratings Sub Menu 18 TV SETUP MENU amp SUB MENUS CONTINUED SLEEPTIMER OFF 15 MIN 30 MIN 45 MIN 60 MIN 90 MIN 120 MIN 180 MIN 240 MIN When the SLEEPTIMER is activated the TV automatically powers down after the specified period of time Note 1 Note 2 The SLEEPTIMER differs from ESP Energy Saving Programmability in that the SLEEPTIMER countdown is unaffected by any command from the remote control or front panel of the TV ESP timer is reset when it receives a command from the remote control or the front panel of the TV When the SLEEPTIMER is active the current SLEEPTIMER countdown timer value appears in the ITV commercial SETUP MENU as well as the FEATURES MENU The SLEEPTIMER countdown period can be adjusted or reset from either menu e SECURITY STANDARD HIGH This feature provides the option to enable access to the SETUP MENU without an RC2573GR setup remote control STANDARD HIGH Note FEATURES MENU CC SLEEPTIMER V CHIP SETUP SAP SOURCE EXIT SLEEPT
11. e SOURCE MENU ITEM NO YES This feature provides the option to specify whether the current FEATURES MENU signal source eg TV 54 AV2 CVI S VIDEO etc item is present or CC in the FEATURES MENU that appears when the SLEEP or CC SLEEPTIMER button on the remote control is pressed or when the MENU or or V CHIP SETUP RECALL button on the guest mode remote control is pressed SAP NO The SOURCE line item does not appear in the or SOURCE FEATURES MENU e EXIT YES The SOURCE line item appears in the FEATURES MENU Features Menu with SOURCE Menu item YES 17 TV SETUP MENU amp SUB MENUS CONTINUED Note 1 When the SOURCE item is highlighted press or 4 on the remote control to step through the signal sources eg tuner AV2 S VIDEO etc that the CHANNEL RING The SOURCE in the FEATURES MENU cannot be used to select RF tuner channels Note 2 The SOURCE item can only be used to select signal sources eg tuner AV2 S VIDEO etc that are in the CHANNEL RING Note 3 If there are no signal sources in the CHANNEL RING other than the presently selected source the SOURCE item is for display purpose only you cannot select any other source e V CHIP MENU ITEM NO YES This feature provides the option to specify whether the V CHIP FEATURES MENU will appear in the FEATURES MENU The V CHIP line item does not appear in the SLEEPTIMER FEATURES MENU or V CHIP SETUP YES The V CHIP li
12. or DCM On Screen Display The display of alphanumeric text that appears over the video image Typically OSD generated by a character generator usually integrated into the television chassis control processor PBS Philips Business Solutions A commercial non consumer division of Philips Consumer Electronics Co of which Philips BDS Business Display Solutions formerly known as ITV is a part Plug Connector on a cable that connects to a plug RC Remote control RC 5 RC 6 Philips IR remote control communication protocols RJ 11 Registered jack 11 Modular telephone style connector form factor with 4 electrical conductors 22 DEFINITIONS ACRYNYMS amp ABBREVIATIONS CONT RJ 12 Registered jack 12 Modular telephone style connector form factor with 6 electrical conductors TUNE Technically also known as a Layer 2 Switch A switching hub that operates at the Data Link Layer Layer 2 and builds a table of the MAC addresses of all the connected stations RTSP Real Time Streaming Protocol Allows control of multimedia streams delivered for example via RTP RFC 3389 Real time Transport Protocol Payload Control includes absolute positioning within the media stream recording and possibly device control RTP Real time Transport Protocol Defines a standardized packet format for delivering audio and video over the Internet See System 7 Remote control mode used to configure Philips Institutional
13. 27HT4000D Philips Business Display 27HT7210D Solutions User Manual For Customer Use Enter below the Serial No which is located on the rear of the cabinet Retain this information for future reference Model No Serial No Thank you for choosing Philips Need help fast Read your Quick Use Guide and or Owner s M anual first for quick tips that make using your Philips product more enjoyable If you have read your instructions and still need assistance you may access our online help at wwW bds philips com or call 1 866 358 9601 while with your product and M odel Serial number PHILIPS TABLE OF CONTENTS Introduction Safety Information 4 Before Calling Service 5 Basic Installation Functions Basic TY COMMECtIONS CPI 6 Rear Jack Panel Connections s cest dard end aurae pne e add 7 jnre aee E rrr 8 Remote Controls Keys 9 LOW Heck CP 9 TV Installation Activating Setup Men pica acd acted ede a hee Sure arie S Ss 10 TY ___ _ 11 LY Set p amp Tn 12 19 Cabinet Dimension Drawings PEASNE DIMENSIONS Tnm 20
14. ANNEL INSTALL gt LABEL NO Channel Guide is not displayed when CH GUIDE on the remote control is pressed and NOT AVAILABLE message appears on the TV screen YES When CH GUIDE button on the remote control is pressed the channel guide is displayed for approximately 10 seconds or until a command is received from the remote control again All RF tuner channels that are in the same channel ring and have labels will appear in the channel list The channel guide appears automatically at power on and remains on screen for approximately 10 seconds or until a remote control command occurs The channel guide also appears when CH GUIDE button on the remote control is pressed To appear in the channel guide an RF tuner channel must be assigned a label and must be saved in the channel ring Only RF tuner channels will be listed in the channel guide Video inputs eg AV2 S VIDEO CVI FRONT A V will not appear POWER ON Note 1 Note 2 16 WELCOME MESSAGE DISPLAY NO YES LINE 1 PHILIPS gt INSTITUTIONAL TV gt LINE 2 CLEAR gt DISPLAY NO YES LINE 1 2 PHILIPS CLEAR CHANNEL GUIDE PBSETPTV gt CBS QVC WB WGN gt gt gt ABC gt gt C SPAN gt CH GUIDE TO SCROLL DOWN TV SETUP MENU amp SUB MENUS CONTINUED REMINDER NO YES When REMINDER is set to YES the current channel or input label will be displayed at the top of the TV screen eg TV2 CVI etc The chan
15. DEO CVI DIGITAL AUTO PROGRAM gt Select the channel or input you wish to configure CHANNEL RING SAVED DELETED LABEL MYLABEL VIDEO BLANK NO YES AUDIO MUTE NO YES with the specific CHANNEL This feature enables you to map re assign a numeric channel number to a video input rather than to its normal RF TV channel ANTENNA channel 2 Select the channel or input you wish to associate TV Setup Channel Install Commercial Mode Note Although it is possible to map a given video source eg CVI to another video source eg S VIDEO this is not advisible as it may lead to confusion AUTO PROGRAM 1 When AUTO PROGRAM is selected the TV performs an automatic search for the presence of viable RF signals at 2 7 its tuner input An AUTO PROGRAMMING ACTIVE 8 9 310 11 12 13 14 TABLE of active numbers will appear When a viable signal 15 16 17 18 19 20 21 is detected on a given channel that channel is highlighted in 23 24 25 26 27 28 red and is added to the channel ring 29 30 31 32 33 34 35 36 37 38 39 40 41 42 2 If CABLE TUNING set to channels 2 through 69 will 43 44 45 46 47 48 49 50 51 52 53 54 55 56 hecked h iable signal is d d i be checked When a viable signal is detected on a given 57 58 59 60 61 62 63 channel that channel is highlighted in red and is added to the channel ring DIGITAL CHANNEL SEARCH 22 Pressing any key on the remote control will terminate the __PRESS ANY KEY ST
16. IMER countdown in progress example The TV SETUP MENU can be accessed by entering a special security code with a guest remote control Refer to Philips sales representative for more details The TV SETUP MENU can be accessed only with an RC2573GR setup remote control in setup mode The default SECURITY setting for Institutional TV is STANDARD When SECURITY is in STANDARD mode the TV is more vulnerable to unauthorized operation 19 271140000 27 DIMENSIONS 19 72 27HT4000D 27 DIMENSIONS ref PDF 8670 000 23831 TITLE COMMENTS INCHES UNITS DATE REVISION D O n A LLI gt a lt 2 A JE gt sis 00 Oo CL we rT TOLERANCE DRAWN BY 20 27HT7210D 27 DIMENSIONS 28 98 27 Es N Z H D LO 02 22 N 70 2 m o A I uc 2 o gt O8 N Z LLI C N N ja olo a 1 NI II Ies ele gt 5405 q vw olo Z 0 o 2 g 5 STV PHILIPS 0 125 PBS TOLERANCE DRAWN BY e 00000 3 n Ni e 21 DEFINITIONS ACRYNYMS amp ABBREVIATI
17. ION 810 21 whe GROUND CLAMPS ELECTRIC SERVICE EQUIPMENT POWER SERVICE GROUNDING ELECTRODE EQUIPMENT NEC ART 250 PART H This bolt of lightning indicates uninsulated material within your unit which may cause an electrical shock Know these For the safety of everyone in your household please do not remove product covering safety symbols RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SER VICING TO QUALIFIED SERVICE PERSONNEL The exclamation point calls attention to features for which you should read the enclosed literature closely to prevent operating and maintenance problems WARNING To reduce the risk of fire or electric shock this appliance should not be exposed to rain or mois ture and objects filled with liquids such as vases should not be placed on this apparatus CAUTION To prevent electric shock match wide blade of plug to wide slot and fully insert ATTENTION Pour viter les chocs lectriques introduire la lame la plus large de la fiche dans la bome correspon dante de la prise et pousser jusqu au fond SAFETY INFORMATION AND USEFUL TIPS SAFETY INFORMATION e Disconnect mains plug when the red light below the TV screen is flashing continuously a bright white line is displayed across the screen cleaning the TV screen Do not use abrasive cleaning agent
18. ONS Automatic Pixel Aging Correction A technique whereby the image displayed on the television screen is periodically shifted slightly for the purpose of minimizing plasma panel phosphor burn in A N Audio video BDS Business Display Solutions See PBS Bit Rate Sometimes written bitrate the frequency at which bits are passing a given physical or metaphorical point quantified in terms of bits per second bit s CVI Component video input Sometimes used interchangeably with YPbPr Composite Video Broadcast Standard Video signal containing combined color luminance and CVBS ae i s synchronization signals Also often referred to as AUX video DB 9 Standardized 9 pin connector typically used for RS 232 asynchronous serial communications DB 15 Standardized 15 pin connector typically used for VGA computer display signals DCM Data Communications Module ITV terminology for devices that communicate with Philips Institutional Television products by means of the Philips ITV SmartPort DFU Directions For Use Philips Consumer Electronics term for product instruction documentation DHCP Dynamic Host Configuration Protocol A protocol used on TCP IP networks Allows client configuration TCP IP address default gateway DNS configuration etc to be sent to clients DNS The network service used in TCP IP networks that translates hos
19. OP _ AUTO PROGRAM session AUTO PROGRAM CHANNEL RING Specify whether the current channel or input is to be SAVED or SKIPPED from the channel ring i e list of channels available for selection with a guest remote control LABEL Input a maximum number of 8 characters for the channel s label Press cursor gt to start the first character Cursor 4 to navigate between character positions within the label field Cursor A or w to select characters from the list A Z or 0 9 etc To exit press cursor gt or 4 to navigate out of the label editing field VIDEO BLANK If VIDEO BLANK is set to NO Video will be displayed If VIDEO BLANK is set to YES Video will not be displayed AUDIO MUTE If AUDIO MUTE is set to INO The current channel is audible If AUDIO MUTE is set to YES The current channel is muted CABLE TUNING NO YES If CABLE TUNING is set to INO You are selecting standard off air tuning If CABLE TUNING is set to YES are selecting cable offset tuning 12 TV SETUP MENU amp SUB MENUS CONTINUED e USE CHANNEL TABLE NO YES If USE CHANNEL TABLE is set to NO The digital tuner will ignore the Virtual Channel Table VCT information that is contained in the Program and System Information Protocol PSIP during channel installation or Direct Channel Command which is sent by the TV set When VCT is ignored the digital tuner will tune to the physical channel Radio Frequency RF Channel Program Map Table
20. ORED STANDARD The will be in standby mode when AC mains power is first applied after being disconnected FORCED The TV will turn ON whenever AC mains power is applied This feature allows the TV s power status to be controlled for example from an AC mains breaker RESTORED When AC mains power is first applied after being disconnected the TV s power status will revert to that when the AC mains power was last removed e CHANNEL DISPLAY NONE NUMBER LABEL ALL Specifies which of the respective channel properties are displayed by the TV s OSD when a channel or input is first selected If REMINDER see REMINDER page 16 is OFF these properties will be displayed for a few seconds then disappear If REMINDER is ON the channel properties remain on screen as long as the TV is on e KEYBOARD LOCK NO YES NO The TV s front panel is enabled YES The TV s front panel is disabled e ESP ENERGY SAVING PROGRAMMASBILITY OFF 1 HR 2 HR 99 HR This feature enables the TV to automatically power down after a specified period of time If during this period it does not receive any commands from the remote control or TV front panel this energy saving feature assumes the TV is inactive and will automatically power down e AUDIO VIDEO MUTE OFF BLACK BLUE Also known as A V muting Suppresses audio and video when the TV tuner is not receiving sufficient RF signal These options produce the following results
21. RETEN US 14 STANDBY MODE LEAVING IN i qa ete RE RC RR e Dai 4 SWIICHAHON CHANNEL a ore dara d Qo ER ad aie 15 VOLUME iat Em mta dme 15 T TABLE OF CONTENTS 2 14 TRA TINGS 18 MODE CHECKING 5561 10 SETUP MEN 11 TYV SETUP MENU ACTIVATING 10 JA SETUP SOE MENUS iur E teen 12 U LIETISACEASS diebus eer a EO Ii CIO 14 CHANNEL TABLE 13 V MENG TIEM uestis TED dE 18 VSCGHIP SETUP US EN EE PRSE SR eee 18 VIDEO BLANK sorrir vov ERES e exe 12 VOLUME desc eee idee ade he anita 14 W WARRANIT pega oc eye ceeds neers oo 24 lads DAS LCD c 13 WELCOME MESSAGE dAn boe t od 16
22. T FIXED 0 000 c cece cece e eere 14 AUDIO VIDEO OUT MUTE creo ba orb Rb xe tesa 15 AUTO PROGRAM CHANNEL INSTALL 12 N 14 B BALANCE TREBLE 14 BATTERY CHECK sss e rele 9 BEFORE CALLING SERVICE ee 4 BRIGHTNESS 14 C CABLE TUNING 000 cece esee 12 CC CLOSED CAPTIONING 17 CHANNEL araara 13 CHANNEL GUIDE oauan aneao e ees 16 CHANNEL RING 12 CHANNEL CHANNEL INSTALL 0 00 c0 ee 12 COLOR 14 COMMERCIAL MODE SELECTING 10 CONSUMER MODE SELECTING 10 CONTRAS 14 CLEANING AND 24 D DEFINITIONS ACRONYMS amp ABBREVIATIONS 22 DEMAGNETIZING CRT eee 4 DIGITAL TV LABELS 13 DISPLAY CHANNEL ima s acneoveuwssaracearacaiwrdeanawseeanesos 15 E EMERGENCY ALERT 000 ce esee 13 END OF LIFE DISPOSAL 000 cece ee 24 ee 15 FACT RESET o oo cece cece cee reel 13 G GUEST MODE REMOTE 0c cece ree 9 INCREDIBLE STEREO 14 INPUT CHANNEL INSTALL 0 00 cece eee enne 12 J JACK PANEL CONNECTIONS REAR 7 L LABEL CHANNEL on ona aonana e eese 12 LANGUAGE TV SETUP onanan oaaao reel
23. a Philips factory service center see enclosed list or authorized service center to arrange repair In U S A Puerto Rico and U S Virgin Islands all implied warranties including implied warranties of merchantability and fitness for a particular purpose are limited in duration to the duration of this express warranty But because some states do not allow limitations on how long an implied warranty may last this limitation may not apply to you TO GET WARRANTY SERVICE IN CANADA Please contact Philips at 1 866 358 9601 In Canada this warranty is given in lieu of all other warranties No other warranties are expressed or implied including any implied war ranties of merchantability or fitness for a particular purpose Philips is not liable under any circumstances for any direct indirect special inci dental or consequential damages howsoever incurred even if notified of the possibility of such damages REMEMBER Please record the model and serial numbers found on the product below Also please fill out and mail your warranty registration card promptly It will be easier for us to notify you if necessary MODEL SERIAL www bds philips com 24 INDEX 27HT4000D 5 5 0000 ceeecee ee 20 27HT7210D 5 ccc ccc e ese ee 21 A AICH AN SWITCH 2 0 ccc e cee e eerie 17 ACCESSING TV SETUP MENUS en 10 AUDIO MUTE CHANNEL INSTALL 000 00 eee ee eee eee ee 12 AUDIO OU
24. artment lid from the back of the remote control Insert two AA sized batteries into the battery compartment making sure the positive and negative polarity line up correctly as indicated inside the case Reattach the battery compartment lid Note Always remove batteries from the remote control if it is not used for a long period of time This is to prevent damage to the remote control due to battery leakage 6 REAR JACK PANEL CONNECTIONS WARNING Risk of electric shock Rear jack panel must be removed by qualified personnel only Do not connect telephone cable or equipment to SmartPlug RJ 12 connector SmartCard slot 42 amp cover A TO BE Do not connect Video In and S Video simulta neously When a Smart Card with Audio Video and S Monitor Video inputs are installed into the Smart Card CABLE ANTENNA Out Y video ih slot the inputs on the Smart Card cannot be Q Ext Spkr OOKO Component connected concurrently with the Video In or S Video and Audio L R In of the TV set or vice versa In this case you can only use either N12 i S VIDEO the inputs on the Smart Card or TV set _ When connecting Y Pb Pr inputs to the mam RL 27HT4000D 27 please note that the correct Audio Applicable to 27HT7210D 27 only In connectors should be the Red amp White jacks under the label AV2 In and not under AV1 In Monitor t
25. ary audio will be audible BALANCE TREBLE BASS 0 63 BALANCE 31 31 Balance Level of sound coming from the left and right speakers Treble Enhance the high frequency sounds Bass Enhance the low frequency sounds Note Adjust the respective audio playback setting using the or 4 cursor e AUDIO OUT FIXED NO YES If AUDIO OUT FIXED is set to YES MONITOR OUT audio level is set to a fixed nominal one volt peak to peak 0 775 volts RMS at 600 ohm irrespective of the TV s volume setting If AUDIO OUT FIXED is set to The MONITOR OUT audio level will vary with the TV s volume setting e SPEAKER MUTE NO YES If SPEAKER MUTE is set to NO The TV s built in speakers will operate as they would normally If SPEAKER MUTE is set to YES The TV s built in speakers will be set to mute INCREDIBLE STEREO NO SPATIAL DOLBY VIRUTAL If INCREDIBLE STEREO is set to NO there will not be any special audio effects applied to the TV sound If INCREDIBLE STEREO is set to SPATIAL the sound from the TV will be specially processed with audio spatializer algorithms resulting in a 3D stereo like effect If INCREDIBLE STEREO is set to DOLBY VIRTUAL the sound from the TV will be specially processed with patented Dolby audio algorithms resulting in a 3D stereo surround effect that conforms to the acoustic performance level as specified by Dolby ULTRA BASS NO YES When ULTRA BASS is set to YES the audio frequency
26. aterials whenever you replace existing equipment LIMITED WARRANTY COLOR TELEVISION One Year Free Labor One Year Free Service on Parts WHO IS COVERED You must have proof of purchase to receive warranty service A sales receipt or other document showing that you purchased the product is considered proof of purchase WHAT IS COVERED Warranty coverage begins the day you buy your product For one year thereafter all parts will be repaired or replaced and labor is free From one to two years from the day of purchase you pay for the replace ment or repair of all parts except the picture tube and for all labor charges After two years from the day of purchase you pay for the replacement or repair of all parts and for all labor charges All parts including repaired and replaced parts are covered only for the original warranty period VVhen the warranty on the product expires the warranty on all replaced and repaired parts also expires WHAT IS EXCLUDED Your warranty does not cover labor charges for installation or setup of the product adjustment of customer controls on the product and installation or repair of antenna systems outside of the product e product repair and or part replacement because of misuse acci dent unauthorized repair or other cause not within the control of Philips Consumer Electronics Company reception problems caused by signal conditions or cable or antenna systems outside the unit
27. channels will not be skipped when 1 Press CURSOR gt or lt to toggle between Added or Skipped If Skipped is selected the channels will scrolling channels with the or CH Note When you are in Digital Mode you can only add or skip programs in Digital Channels Weak Sig Dig Digital broadcasting is still new Therefore it is not uncommon for a broadcaster to only send out a digital signal for part of a day The reception could also come and go If you program your channels when the signal is not being sent or is weak it will not be saved in your channel setup Using the Weak Digital Signal feature here you can add those channels with weak or no signals to your channel list Adding or skipping Weak Digital Signal can ONLY be done in Digital Mode AutoLock not supported Fact Ch Reset Factory Channel Reset feature lets you erase the contents of the master user and favorite channel lists This restores the TV to the initial state before the first Auto Program operation For instructions on how to Auto Install the TV again refer to page 11 Digital Audio Digital Audio allows you to switch to another audio language when it is available Timer not supported Closed Caption Closed Caption lets you select the default option or options that you have assigned to your Close captioning service This feature is ONLY available in Digital Mode Emergency Alert Emergency Alert lets you display or discard emergency alerts for Low or Medi
28. control is pressed This is how to set the Welcome Message When the WELCOME MESSAGE setup menu is highlighted Press cursor gt or 4 on the remote control to invoke the 1 WELCOME MESSAGE sub menu Press cursor A or W on the remote control to select the desired MESSAGE sub menu item eg LINE1 LINE2 remote control to select YES or NO When YES is selected WELCOME MESSAGE is enabled Choose NO to disable WELCOME MESSAGE Note If Welcome Message is enabled but both LINE 1 and LINE 2 are blank or consist entirely of space characters no message will appear Select message LINE 1 or LINE 2 Press cursor gt on the 4 remote control to start the first character A blinking will appear indicating that you are in the edit mode Press cursor A to select a character at the given position To move to a desired character position press or When you cursor to the left or right margins of the edit space the blinking will disappear and gt will re appear at the end of the menu line You can then cursor A or to the next or previous line in the MESSAGE sub menu D Select CLEAR to erase the entire message 3 When DISPLAY is highlighted press cursor or 4 on the Note e CHANNEL GUIDE NO YES POWER ON The channel guide feature provides an on screen summary listing of the RF tuner channels that are currently in the channel ring see CHANNEL INSTALL gt CHANNEL RING and have been assigned labels see CH
29. djustments brightness contrast color tint poor or no picture Snowy noisy 1 Check antenna cable and or setup box connections Ensure that they are properly connected picture 2 Possible electrical interference from appliances or other sources BASIC TELEVISION CONNECTION SN B REMOTE STANDBY POWER PHILIPS PANEL STANDBY POWER EXAMPLE ANTENNA CONNECTION e Connect the antenna or RF cable signal to the 75 ohm RF F connector socket located on the TV s rear jack panel MAINS CONNECTION e Ensure that the mains voltage and frequency are correct Please refer to the product labelling and documentation Note The power button on the front panel does not disconnect the television from the AC mains It toggles the TV between on and standby mode To completely turn off the AC mains power you must unplug the AC mains plugs from the wall socket SWITCHING ON THE SET e X Press the power button on the TV s front panel on the remote control to switch the TV set on Note If the TV is in commercial mode it might not respond to the front panel or the remote control Please refer to the section on TV Installation and TV Setup Menu in this documentation for more informaton USE amp CARE OF REMOTE CONTROL To load the supplied batteries into the remote control Remove the battery comp
30. equalization is modified such that the bass frequencies are significantly emphasized VOLUME BAR NO YES When VOLUME BAR is set to YES an OSD graphic appears providing visual verification eg 15 of volume adjustments made with the remote control or the front panel of the TV 14 TV SETUP MENU amp SUB MENUS CONTINUED e MIN VOLUME O 63 Specify the lowest volume setting possible by using the remote control or the TV front panel if it is not locked out This setting cannot exceed the MAX VOLUME e MAX VOLUME 63 Specify the highest volume setting possible by using the remote control or the TV front panel if it is not locked out This setting cannot be less than the MIN VOLUME e SWITCH ON VOLUME STANDARD O 63 Specify the volume setting that takes effect when the TV is powered on lf STANDARD the volume at power on will be the volume at which the TV was prior to last power down If specified as 0 63 that will always be the volume at power on until SWITCH ON VOLUME is changed e SWITCH ON CHANNEL STANDARD TV 1 125 AV2 SIDE S VIDEO Specify the channel which the TV will be tuned when it is powered on If STANDARD the channel at power on will be the same as the channel when the TV was tuned at last power down If specified eg 2 AV2 CVI etc then that will be the channel at power on until SWITCH ON CHANNEL is changed e POWER ON STANDARD FORCED REST
31. gisters stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and third grounding prong The wide blade or third prong are provided for your safety When the pro vided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus Only use attachments accessories specified by the manufacturer Use only with a cart stand tripod bracket or table speci fied by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over Unplug this apparatus during lightning storms or when unused for long periods of time Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped This product may contain lead and mercury Disposal of these materi als may be regulated due to environmental considerations For dis posal
32. k to issue device discovery packets YPbPr Component video signals consisting of luminance and blue and red components 23 CLEANING amp CARE To avoid possible shock hazard please be sure that the television is unplugged from the electrical outlet before cleaning When cleaning the television screen take care not to scratch or damage the screen surface avoid wearing jewelry or using anything abrasive Wipe the front of the screen with a clean cloth dampened with water Use even easy vertical strokes when cleaning Gently wipe the cabinet surfaces with a clean cloth or sponge dampened in a solution of cool clear water Use a clean dry cloth to dry the wiped surfaces Occasionally vacuum the ventilation holes or slots in the cabinet back Never use thinners insecticide sprays or other chemicals on or near the cabinet as they might cause permanent damage of the cabinet finish END OF LIFE DISPOSAL This Philips Institutional Television product and its packaging contain materials that can be recycled and re used Specialized companies can recycle your product to increase the amount of reusable materials and minimize the amounts which need to be properly disposed This product might also use batteries which should not be thrown away when depleted but should be handed in and disposed of as small chemical waste Please find out about the local regulations regarding the disposal of the television batteries and packaging m
33. nalog OFF CC 1 CC 2 CC ON MUTE Digital OFF CC6 MUTE SAVE CC NO YES e SOURCE MENU ITEM NO YES e V CHIP MENU ITEM NO YES SAVED V CHIP NO YES V CHIP SETUP gt SLEEPTIMER OFF 15 MIN 30 MIN 45 MIN 60 MIN 90 MIN 240 MIN e SECURITY STANDARD HIGH Only 8 menu items will be displayed at one time 1 To scroll through the menu press A or v on the remote control A highlight indicates that the respective menu item s setting is selected for modification 2 To modify the setting of the selected menu item press or 4 3 To exit press or RECALL on the RC2573GR setup remote control Note Digital TV Label option will only appear when the When the channel is analog Digital TV Label option will not be available Note denotes item which appears in both the Commercial and Consumer modes Note denotes item which appears only in Commercial mode 11 button is pressed in a Digital Channel selection TV SETUP MENU amp SUB MENUS LANGUAGE ENGLISH ESPANOL FRANCAIS When you first enter the TV SETUP Menu LANGUAGE is highlighted Scroll to the LANGUAGE item select other languages with the gt or 4 button on the remote control CHANNEL INSTALL gt When selected CHANNEL INSTALL menu appears Configure the inputs and channels as seen here CHANNEL INSTALL CHANNEL TV 2 125 AV2 SIDE S VIDEO CVI DIGITAL INPUT INPUT ANTENNA AV2 SIDE S VI
34. ne item appears in the FEATURES SAP MENU or SOURCE x e EXIT Features Menu with V CHIP Menu item YES Note The FEATURES MENU can be activated by pressing the SLEEP or CC button on remote control RC2573GR or by pressing the RECALL or MENU button on the guest remote control e SAVED V CHIP NO YES This feature provides the option to specify whether the V CHIP SETUP configuration remains in effect after the TV is powered down NO The current V CHIP setup configuration reverts to defaults does not appear on the FEATURES MENU when the TV is powered down YES The current V CHIP setup configuration remains in effect when the TV is powered down V CHIP SETUP NO YES Configures the V CHIP program content viewing restriction feature Please consult the mainstream consumer product documentation for details about V CHIP SETUP this feature MASTER DISABLE YES NO MASTER DISABLE NO The TV and Movie Ratings will be effective TV RATINGS MASTER DISABLE YES TV and Movie Ratings will be blocked MOVIE RATINGS overwriting all previous settings EXIT TV RATINGS TV RATINGS To select TV Ratings highlight TV RATINGS and press cursor gt on the remote control to invoke the TV Ratings sub menu Navigate with cursor A gt or 4 on the remote control to select the ratings you wish to block When the cursor is in the desired bracket press A or W to activate it An X will appear indicating that the TV Rating has
35. nel number or input label if a label has been assigned in CHANNEL INSTALL and the current MUTE status i e if sound is MUTED will also be displayed when available When REMINDER is set to NO the reminder information will appear only when the channel or input label is changed This reminder information will disppear after ten seconds e 3 DIGIT ENTRY NO YES YES Upon receiving a signal from the remote control the TV expects to receive up to two more successive remote digit commands eg 123 012 etc before tuning to the intended channel As the TV receives the signal from the remote control each digit will be displayed on the top left hand corner of the TV screen This digit will be followed by a indicating that the TV is waiting for the digit input see Note NO Upon receiving a signal from the remote control the TV expects to receive one more successive remote control digit conmand before tuning to the intended channel see Note Note Successive digit commands must occur within two seconds or the TV will interpret the received digit s as the intended channel and tune to it accordingly e A CH A V SWITCH NO YES The A CH A V alternate channel A V switch feature provides the choice to use the remote control A CH command to toggle between the previously viewed channels inputs to step successively through all sources eg ANTENNA tuner AV2 S VIDEO CVI FRONT presently in the channel ring YES Upon receiving
36. nnot be turned on if it is Or cannot be turned off if TV is on TV turns off by 1 TV automatically turns off after approximately 5 mintues when no RF signal is present unless itself POWER ON FORCED Installation 2 Check Energy Saving Programmability setting see ESP in TV installation setup Picture No Picture 1 Check that the antenna cable is connected properly at the rear of the TV 2 Check CABLE TUNING setting NO YES 3 Possible TV station problem Try another channel There is picture 1 Try increasing the volume but no sound Picture 2 Check that the sound is not muted If it is press the MUTE button on the remote control to restore sound Picture Display Uneven color 1 Switch off the TV using the mains power button Wait approximately 20 minutes before turning display on the TV again 2 Ensure that the TV is not placed near any speakers or magnetic objects Check antenna cable or set top box Ensure that the TV s AC power cord is plugged into the main socket If there is still no power dis connect the plug Wait for 60 seconds and re attach plug Turn on the TV again Picture Display Double image ghost image Power 1 Check batteries Remote Control TV does not respond to remote control 2 Aim remote control directly at remote control sensor lens on TV and try pressing any button on the remote control There is sound but Check picture a
37. or recycling information please contact your local authorities or the Electronic Industries Alliance www eiae org B Objects have fallen or liquid has been spilled into the appliance or C The appliance has been exposed to rain or D The appliance does not appear to operate normally or exhibits a marked change in performance or E The appliance has been dropped or the enclosure damaged 17 Tilt Stability All televisions must comply with recommended inter national global safety standards for tilt and stability properties of its cabinet design Do not compromise these design standards by applying excessive pull force to the front or top of the cabinet which could ultimately overturn the product Also do not endanger yourself or children by placing electronic equipment toys on the top of the cabinet Such items could unsus pectingly fall from the top of the set and cause product damage and or personal injury 18 Wall or Ceiling Mounting The appliance should be mounted to a wall or ceiling only as recommended by the manufacturer 19 Power Lines An outdoor antenna should be located away from power lines 20 Outdoor Antenna Grounding If an outside antenna is connected to the receiver be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges Section 810 of the National Electric Code ANSI NFPA No 70 1984 provides information with respect to pro
38. per grounding of the mast and supporting structure grounding of the lead in wire to an antenna dis charge unit size of grounding connectors location of antenna dis charge unit connection to grounding electrodes and requirements for the grounding electrode See Figure below 21 Object and Liquid Entry Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings 22 Battery Usage CAUTION To prevent battery leakage that may result in bodily injury property damage or damage to the unit Install all batteries correctly with and aligned as marked on the unit Do not mix batteries old and new or carbon and alkaline etc Remove batteries when the unit is not used for a long time Note to the CATV system installer This reminder is provided to call the Damage Requiring Service The appliance should be serviced by system installer s attention to Article 820 40 of the NEC that provides qualified service personnel when A The power supply cord or the plug has been damaged guidelines for proper grounding and in particular specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE NEC GROUND CLAMP ANTENNA LEAD IN WIRE ANTENNA DISCHARGE UNIT NEC SECTION 810 20 GROUNDING CONDUCTORS NEC SECT
39. ress the button on the remote control to store the change The TV will go to standby mode UJ Press the Power On key on the remote control to switch the TV on again Follow the procedure in Part B to activate the TV Setup Menu 10 TV SETUP MAIN MENU LANGUAGE ENGLISH CHANNEL INSTALL gt CABLE TUNING NO YES USE CHANNEL TABLE NO YES e DIGITAL TV LABEL NO YES e DTV SETUP BRIGHTNESS IHI O 63 COLOR HT O 63 CONTRAST HUI O 63 SHARPNESS HITT O 63 TINT 31 31 x NOISE REDUCTION NO YES SOUND MODE MONO STEREO SAP NO YES AVL NO YES BALANCE 31 31 TREBLE IUL 0 63 BASS HILL O 63 e AUDIO OUT FIXED NO YES SPEAKER MUTE NO YES INCREDIBLE STEREO NO SPATIAL DOLBY VIRTUAL ULTRA BASS YES NO VOLUME BAR YES NO e MIN VOLUME 63 MAX VOLUME 63 SWITCH ON VOLUME STANDARD O 63 SWITCH ON CHANNEL POWER ON CHANNEL DISPLAY STANDARD TV 1 125 AV2 SIDE S VIDEO STANDARD FORCED RESTORED NONE NUMBER LABEL ALL KEYBOARD LOCK _ESP AUDIO VIDEO MUTE NO YES OFF 1 HR 2 HR 99 HR OFF BLUE BLACK AUDIO VIDEO OUT MUTE YES e MONITOR OUT NO YES WELCOME MESSAGE gt e CHANNEL GUIDE NO YES POWER ON REMINDER NO YES 3 DIGIT ENTRY NO YES e A CH A V SWITCH NO YES A
40. s Use a slightly damp chamios leather or soft cloth there is lightning or thunder storm the set is left unattended for a prolonged period of time e Do not place open flames near or on the Do not place TV set under direct sunlight e Leave at least 4 inches space around each side of the TV for ventilation purpose This is to avoid over heating e Do not expose your TV set to rain or moisture USEFUL TIPS e Do not leave the TV in standby mode for a prolonged period of time Switch off TV set to allow the CRT to be de gaussed demagnetized A de gaussed CRT TV will have optimum picture quality e Do notre position the TV while it is switched on It may cause non uniformity uneven color in display color e Do not attempt to repair a defective TV Always consult a skilled service technician BEFORE CALLING SERVICE Check this list of symptoms and suggested steps to take before requesting service You may be able to solve the problem yourself Note Please become familiar with the commercial features as described in TV installation Setup because the effects of several of these features if not thoroughly understood might appear as faulty operation SYMPTOMS SUGGESTED STEPS TO TAKE Installation TV does not 1 Check commercial TV setup TV installation setup menu including power forced on front respond to keypad lockout channel ring volume minimum maximum features commands volume channel power or ca
41. t To activate Channel Guide function To toggle between available video Standby sources T Press to switch the TV off or on Captioti CC SOURCE GUIDE PLAY To activate Close Caption function DVD Play DVD Pause Press to switch the TV off or on To Pause DVD playback DVD Stop DVD Rewind To stop DVD playback if applicable To rewind DVD playback Smart Sound DVD Fast d To select predefined sound settings ast rorwar To Fast Forward DVD playback if Sleep applicable Activate the sleep timer Press repeatedly to increase countdown time Smart Picture To select predefined picture settings OK To confirm a selection Menu To call up or exit the menu VOL ume To adjust TV volume CH annel or CH annel To select channels Mute Turn the sound on or off 0 9 Digit Keys To select a TV channel For a two digit program number enter the second digit before the dash appears Alternate Channel To toggle between alternating channels 16 9 Formats To adjust TV screen formats PHILIPS LOW BATTERY CHECK Press the key for approximate 5 seconds The following text appears SERVICE 1 REMOTE BATTERY OK If the word LOW appears instead of the batteries are low and must be replaced 9 ACTIVATING TV SETUP MENU The following remote control commands are applicable to Philips Business Display Solutions TV products These can be used for setup and configuration purposes WITH GUEST
42. t names to IP addresses DVI Digital Visual Interface a digital interface standard created by the Digital Display Working Group DDWG to convert analog signals into digital signals to accommodate both analog and digital monitors Guest Mode First data word of a Philips RC 5 RC 6 remote control code for standard television commands Hypertext Markup Language The set of markup symbols or codes inserted in a file intended for display HTML ona World Wide Web browser page IR Infra red long wavelength light energy invisible to the human eye In this context as applied to wireless remote controls IR FACE ITV interface module that adds ITV features and connectivity to non ITV televisions MP3 A compressed digital audio format MPEG Motion Pictures Experts Group Layer 3 Audio compression Moving Picture Experts Group General term for a range of audio and video compression and the name MPEG of the standards organization for digital video and digital audio compression Operates under the auspices of the International Organization for Standardization ISO ITV Institutional Television See PBS Commercial non consumer division of Philips Consumer Electronics Co NA Not available not applicable NC Not connected no connection Off See Standby On A state of operation in which the unit television is connected to an AC power source in active use and capable of responding to queries or commands from a control device IR remote control and
43. um priority Note Emergency Alert will not be visible if no broadcast is received or when the TV is in Standby mode 13 TV SETUP MENU amp SUB MENUS CONTINUED BRIGHTNESS COLOR CONTRAST SHARPNESS TINT 0 63 TINT 31 31 Adjust the respective picture setting using the or 4 cursor NOISE REDUCTION NO YES If NOISE REDUCTION is set to NO The noise reduction feature is disabled If NOISE REDUCTION is set to YES Video noise is reduced with minimum reduction in picture sharpness SOUND MODE MONO STEREO Select either STEREO or MONO sound modes When SOUND MODE is changed an on screen display will appear indicating the actual audio status MONO or STEREO Note lf Stereo is not available on a selected show the sound coming from the TV will remain in the Mono mode even if the TV set to Stereo mode AVL Auto Volume Leveler NO YES When turned to YES AVL will level out the sound being heard when sudden change in volume occurs during commercial breaks or channel changes SAP NO YES Disable or enable the Second Audio Program channel features SAP is not widely used and most channels do not transmit a SAP signal Use of the SAP channel include Spanish translation or other language translation Descriptive information about the program Duplication of main audio mono Audio unrelated to program Note When SAP is set to YES but SAP is not present on the current channel the prim
Download Pdf Manuals
Related Search