Newstar FPMA-D940
Contents
1. Ans computerproducts WWW NEWSTAR NL LCD MONITOR ARM FPMA D940 FPMA D940HC 2007 07 Loading 4 9kg 8 8 19 8 Ibs FPMA D940 FPMA D940HC 8 15kg 17 6 33 Ibs LCD Monitor Arm L FPMA D940 FPMA D940HC Range of use angle Loading FPMA D940___ 4 9kg 8 8 19 8 Ibs FPMA D940HC 8 15kg 17 6 33 Ibs GROMMET MOUNTING y Range of use angle Before assembly please spend some time to read this and follow the procedures step by step Some panels are viewed differently from the detail drawing below This is for extra clarity Do not discard any of the packaging until you have checked all the parts and the package of fittings If you miss any of the parts please contact the store where you purchased your products The staff will do their best to help you FPMA D940 FPMA D940HC Fitting Tools Part Check List Check List GROMMET MOUNTING y X Fitting Tools Check List C T K Twy X Part Check List X1 X1 X2 X1 X1 Z 6mm FPMA D940 FPMA D940HC Clamp assembly step Adhere the pad to the clamp base Desk thickness from 20mm 50mm Then fix the clamp on the desk Grommet assembly step 1 2 To assemble the small metal plate on the bottom concavity of the grommet set then adhere the pad to the grommet set which is touch with desk surface Then fix the grommet set on the desk through a bolt and parts as figur2. es below Desk thickness from 20mm 50mm The diameter of the hole is from 20mm tog 50mm GROMMET MOUNTING Grommet assembly step 1 1 Use 2mm allen key to lose screw Then take out the arm up Notice Don t make the screw drop Grommet assembly step 1 3 Fix the grommet mount on the desk Use 2mm allen key to secure the pole and the grommet mount with the screw to the bottom and than move backward 1 circle Note Before secure the screw please make surea concavity which on the bottom of the arm if aim at the small hole position together Move the knob out first then pull it down to open the VESA adapter plate switch then take it up form the arm Step 3 Place LCD with facing downward on flat surface Place VESA adapter plate on the LCD back as figure and align to the screw holes Secure them together with four screws And then tighten them up with screwdriver not provided 75mmx75mm 100mmx100mm VESA interface Insert the VESA adapter plate with LCD display on already into the arm and press it down Then push the knob up as figure Step 5 1 Use cable tie supplied to 2 Move the cable cover up finish cable management then to open it for finish cable management i Cable tie Adjustment For Loading Caution for weight capacity adjustment 1 Make sure of the LCD panel weight 2 Support arm with a hand during assembl
3. y Adjustment Use the Allen key provided to adjust the weight capacity Twist the Allen key in a clockwise direction for less weight counterclockwise direction for more weight FPMA D940___ 4 9kg 8 8 19 8 Ibs FPMA D940HC 8 15kg 17 6 33 Ibs ui oy Adjusting Universal Joint Tension When assembling the arm with monitors of differing weights you may find that the tension of the universal joint needs to be adjusted to ease movement or to maintain the desired monitor position If so adjust as follows Screw Head a Remove the plastic universal joint cover b Find the nylon nut not the screw head and use the included wrench to adjust the tension c Use one hand to support the monitor and adjust the tension Of the universal joint eClockwise more tension eCounterclockwise less tension d When the desired tension is achieved replace the plastic cover Caution eSupport the monitor during the adjustment procedure eOnly adjust the nylon nut not the screw head eDo not disassemble the universal joint
Download Pdf Manuals
Related Search