cultivator (s-cv-43)
Contents
1. To Remove Tines 1 Remove the pins from each end of the tine shaft Refer to Figure 3 2 Slide the four tines off the tine shaft To Install Tines The 4 different tines are labeled A B C and D Refer to Figure 4a for the location of the label For a 10 tilling width 1 Assemble the tines as shown in Figure 4b Make sure the collars of the tines are facing each other 2 Insert the pins into the holes at each end of the tine shaft to lock the tines into place See Figure 3 For a 7 tilling width 1 Only assemble tines B and C the two inside tines Do not assemble tines A and D the two outside tines Refer to figure 4b 2 Insert the pins into the INSIDE holes of the tine shaft to lock the tines into place See Figure 5 Questions Call Toll Free at 1 800 737 2112 6 Copyright 2009 MAT Engine Technologies LLC Operation e Save all instructions AJ Before Starting Engine Mixing Fuel 2 Cycle Oil A WARNING Do not smoke or allow smoking near fuel or the cultivator Mix and pour fuel outdoors WHERE THERE ARE NO SPARKS OR FLAMES The 2 cycle engine on your cultivator requires that fuel and 2 cycle engine oil need to be pre mixed before adding to the fuel tank A WARNING Always mix the gasoline and 2 cycle oil in a container approved for gasoline Never mix fuel directly in the engine fuel tank Use fresh unleaded gasoline with an octane rating of 87 or higher and less t2. s manual METL recommends that you retain all receipts covering maintenance on your SORE but METL can not deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance e As the SORE owner you should however be aware that METL may deny your warranty coverage if your SORE or a part has failed due to abuse neglect improper maintenance or unapproved modifications e You are responsible for presenting your SORE to a distribution center or service center authorized by METL as soon as the problem exists The warranty repairs should be completed in a reasonable amount of time not to exceed 30 days If you have any questions regarding your warranty T If you need assistance or have any questions coverage you should contact METL customer service CALL TOLL FREE 1 800 737 2112 Questions Call Toll Free at 1 800 737 2112 12 Copyright 2009 MAT Engine Technologies LLC Wa rra nty Continued e Save all instructions Defects Warranty Coverage METL warrants to the original purchaser and each subsequent purchaser that the small off road engine SORE 1 has been designed built and equipped so as to conform with all applicable regulations and 2 is free from defects in materials and workmanship that cause the failure of a warranted part to conform with those regulations as may be applicable to the terms and conditions stated below a The warranty period begins on the date the en
3. 3 SOUTHLAND Operator s Manual GASOLINE POWERED CULTIVATOR 43cc 2 Cycle MODEL No CV 43 For Occasional Use Only Look inside for Page Safety Definitions 1 Important Safety Information 2 3 Product Specifications 4 Parts amp Features 4 Assembly 5 6 Operation 7 8 Maintenance 9 Storage 9 Troubleshooting 10 Technical Service 10 Warranty 11 16 IMPORTANT Thank you for purchasing this Southland Cultivator Read and understand all warnings and instructions in this manual before using this tool Improper use of this tool can cause severe injury or death Keep this manual for future reference Record the following for future reference Mfg Date Code Date of Purchase Attach a copy of your sales receipt Consumer Toll Free Number 1 800 737 2112 Refer to the website for electronic manual and parts book www gardnerinc com T If you have a question or problem CALL TOLL FREE 1 800 737 2112 KEEP THIS MANUAL FOR FUTURE REFERENCE 10 30 09 Printed in China A200485 Important Safety Information Safety Definitions e Save all instructions Safety Warning Symbols ddd 6X PUSH TO Indicates WARNING DANGER or CAUTION Read operator s manual before operating this machine Failure to follow directions could result in serious injury Always wear eye protection that meets or exceeds the requirements of ANSI Z87 1 Wear hearing protection Wear breathing protection Do not use
4. Keep children and pets away Use only for jobs explained in this manual Do not use cultivator for any job except that for which it is intended Maintain your balance and proper footing at all times Do not overload the machine capacity by attempting to till too deep 9 After striking a foreign object stop the engine remove the wire from spark plug thoroughly inspect the machine for any damage and repair the damage before restarting and operating the machine 10 Never leave the machine unattended Stop the engine when leaving the operating position 11 Stop the engine before unclogging the tines and when making any repairs adjustments and inspections 12 Be careful when tilling in hard ground The tines may catch in the ground and propel the cultivator forward If this occurs let go of the handles and do not restrain the machine 13 Use extreme caution when reversing or pulling the machine towards you 14 Do not force cultivator It will do the job better and with less likelihood of a risk of injury at the rate for which it was designed Never start or run the unit inside a closed room or building breathing exhaust fumes can kill 16 Exercise extreme caution when operating on or crossing gravel drives walks or roads Stay alert for hidden hazards or traffic 17 Exercise caution to avoid slipping or falling 18 If the unit should start to vibrate abnormally stop the engine and check immediately for the cause Vibration is
5. SOREs must be designed built and equipped to meet the State s stringent anti smog standards METL must warrant the emissions control system on your SOREs for the periods of time listed below provided there has been no abuse neglect or improper maintenance of your SOREs Questions Call Toll Free at 1 800 737 2112 11 Copyright 2009 MAT Engine Technologies LLC Wa rra nty Continued e Save all instructions Other U S States Territories In other areas of the Unites States your outdoor power equipment engine must be designed built and equipped so as to conform at the time of sale to U S EPA emissions standards for small off road spark ignition engines at or below 19 kilowatts All of the United States Your emission control system may include parts such as the carburetor or fuel injection system fuel lines the ignition system and catalytic converter Also included may be hoses belts clamps connectors and other emission related assemblies Where a warrantable condition exists METL will repair your small off road engine at no cost to you including diagnosis parts and labor Manufacturer s Warranty Coverage The emissions control system is warranted for two years If any emissions related part on your engine is defective the part will be repaired or replaced by METL Owner s Warranty Responsibilities e As the SORE owner you are responsible for the performance of the required maintenance listed in your owner
6. generally a warning sign of trouble 19 Never operate the machine at high transport speeds on hard or slippery surfaces 20 Start the engine carefully according to instructions and with feet well away from the tines Questions Call Toll Free at 1 800 737 2112 2 Copyright 2009 MAT Engine Technologies LLC ONOaRWND da 2 2 gt ie T Q Important Safety Information continued e Save all instructions While Operating Cultivator cont 21 Never pick up or carry a machine while the engine is running Prolonged exposure to vibrations through use of gasoline powered hand tools could cause blood vessel or nerve damage in fingers hands and joints of people prone to circulation disorders or abnormal swellings Extensive use in cold weather has been linked to blood vessel damage in otherwise healthy people If symptoms occur such as numbness pain loss of strength change in skin color or texture or loss of feeling in the fingers hands or joints discontinue the use of this tool and seek medical attention Fuel Safety 1 Mix and pour fuel outdoors WHERE THERE ARE NO SPARKS OR FLAMES 2 Use a container approved for gasoline 3 Do not smoke or allow smoking near fuel or the cultivator 4 Avoid spilling fuel or oil Wipe up all fuel spills 5 Move at least 10 feet 3 meters away from fueling site before starting engine Do not refuel a hot engine Do not ref
7. housing to prevent dirt and debris from entering the engine Accumulated debris and dust in the air filter will reduce engine performance increase fuel consumption and increase the risk of damage Inspect the air filters frequently for dust and debris build up and clean the air filters every 5 hours of operation more frequently in dusty dirty conditions Both air filters should be cleaned by following these instructions 1 Before removing air filter cover brush away any loose dirt or debris on and around the filter cover 2 Remove the screw securing the air filter cover See Figure 13 3 Remove and clean foam filter e Light surface dust can readily be removed by tapping the filter e Heavy deposits should be washed out in soap and water Squeeze out any remaining water and allow the filter to completely dry A WARNING Never clean filter in gasoline or other flammable solvents 4 Add a drop of thin oil to the filter and replace it B BEAUT Inspect the spark plug after every 10 15 hours of use adjust spark plug gap and replace spark plug as necessary Replace spark plug every year to maintain engine performance and easy starting To inspect or replace the spark plug 1 Remove the insulated spark plug boot 2 Use the spark plug wrench to remove the spark plug by turning counter clockwise 3 Visually inspect the spark plug for cracks or damage If damaged replace spark plug with a recommended replacement
8. until engine starts and runs This could require pulling the recoil starter handle many times depending on how badly the unit is flooded 6 If the engine still does not start allow the unit to sit for about 15 minutes and repeat steps 1 5 If the unit still doesn t start refer to the TROUBLESHOOTING section of this manual or CALL TOLL FREE 1 800 737 2112 T If you need assistance or have any questions D Adjusting Engine Speed Note this cultivator is equipped with a centrifugal clutch so the tines will not turn until the engine speed is increased To increase the engine speed lift up on the throttle trigger See Figure 10 To slow the engine down slowly release the throttle trigger Completely releasing the throttle lever will return the engine to idle and will stop the tines from rotating E Stopping the Engine 1 Release the throttle trigger and allow the engine to idle for a few moments See Figure 10 2 Push and hold the ignition switch to the stop position See Figure 6 Adjusting the Drag Stake Position The drag stake adds resistance when cultivating which makes the unit easier to control It also can be adjusted to change the depth of cultivating To adjust the drag stake position follow the steps below and refer to Figure 11 1 Remove the detent pin 2 Slide the stake to the desired position aligning the hole in the stake with the holes in the support bracket 3 Insert the dete
9. Capacity 28 oz 840 ml 2225 eeeesWeeeceest ane eeee oeed CHAMPION CJ7Y Fuel Type Unleaded Gasoline 87 Octane or higher 0 00 cee eee ete or equivalent Net Weight 00005 33 Ibs 15 kg Parts amp Features Upper Handle ie Recoil Starter Handle Throttle Trigger Lower Handle Spark Plug Drag Stake a re F Transpor Wheel Questions Call Toll Free at 1 800 737 2112 Copyright 2009 MAT Engine Technologies LLC Assembly e Save all instructions If you need assistance or find any parts missing CALL TOLL FREE 1 800 737 2112 Parts Included with Cultivator e Middle Handle 1 e Cable Ties 3 e Upper Handles 2 e Operator s Manual 1 e Wing nuts and bolts 4 ea e 3 2 oz bottle of 2 Cycle engine oil 1 e Spark Plug Wrench amp Rod 1 Wrench 1 A WARNING Do not operate cultivator if it is damaged or not securely and fully assembled How to Unpack Cultivator from Carton 1 Remove all parts and packing components 2 Use a utility knife to cut all 4 vertical edges Lay the side panels flat around the cultivator 3 Remove inner components and packaging A CAUTION Use care when removing parts not to damage any cables or wires that are attached to the parts 4 Roll the unit out from the carton and place on a hard level surface How to Assemble the Handles and Drag Stake Kg Right Upper W Handle 7 A Wire f Left Upper a D Ha
10. Spark Plug 5 Check for kinked or split fuel line repair or replace 6 Contact a qualified service center 1 Check for kinked or split fuel line repair or replace 2 Clean air filter 3 Clean or replace spark plug 4 Contact a qualified service center 5 Contact a qualified service center 6 Contact a qualified service center 1 Empty Fuel Tank and refill with correct fuel mixture 2 Clean or replace air filter 3 Contact a qualified service center 4 Rotate choke lever to the RUN WARM START position 1 See Mixing Fuel 2 Cycle Oil in OPERATION section 2 Replace with correct Spark Plug 3 Contact a qualified service center 4 Contact a qualified service center 1 Contact a qualified service center 2 Contact a qualified service center 3 Contact a qualified service center T If you need assistance or have any questions CALL TOLL FREE 1 800 737 2112 When contacting the Technical Service Department have ready e Your Name e Your Address e Your Phone Number e Model Number of Product Date of Purchase include copy of receipt for written requests Questions Call Toll Free at 1 800 737 2112 10 Copyright 2009 MAT Engine Technologies LLC Warranty e Save all instructions EY southtand CULTIVATOR Limited Warranty Always specify model number when contacting the factory We reserve the right to amend these specifications at any time without notice The only warran
11. e the machine and will void the warranty 8 Keep handles dry clean and free from oil and grease 9 Allow engine to cool and empty the fuel tank before storing or transporting in vehicle Use up remaining fuel in the carburetor by starting the engine and letting it run until it stops If the fuel tank has to be drained do it outdoors 10 When not in use store cultivator indoors in a dry location Store cultivator above the reach of children or in a locked area out of the reach of children 11 Store unit and fuel in area where fuel vapors cannot reach sparks or open flames from water heaters electric motors or switches furnaces etc 12 Always refer to the operator s manual for important details if the cultivator is to be stored for an extended period 13 Follow manufacturer s recommendations for safe loading unloading transport and storage of machine Questions Call Toll Free at 1 800 737 2112 3 Copyright 2009 MAT Engine Technologies LLC Product Specifications e Save all instructions Engine cede nsen tes dese cede 43 cc 2 cycle Full Crank 2 Cycle Oil Type 2 Cycle Oil that meets or exceeds Idle Speed 0 00000 2 800 3 000 RPM 1 eee ee ees JASO FC Specifications Tilling Width 2 cs seeeteeteencme chads deeucegs 7 10 Fuel Mixture 40 1 Gasoline 2 Cycle Oil Tilling Depth 02 020 eee eee Up to 5 Spark Pls cups cdecad canev ae ee eas NGK BPMR7A Fuel Tank
12. ed to the purchase price of the product and MAT Engine Technologies LLC shall not be liable for any other damages whatsoever including indirect incidental or consequential damages Some states do not allow limitation of how long an implied warranty lasts or an exclusion or limitation of incidental or consequential damages so the above limitation of damages may not apply to you This warranty provides the original purchaser with specific rights For information regarding those rights please consult the applicable state laws METL Corporate Office CORRESPONDENCE ONLY ATTN Technical Service METL 6700 Wildlife Way Long Grove IL 60047 B Federal and California Emissions Control Warranty Statement This MAT Engine Technologies LLC METL outdoor power equipment engine complies with the emissions regulations of Southland Model No Regulatory Agency S CV 43 United States Environmental Protection Agency U S EPA and State of California To the extent there is any conflict between this Emissions Control Warranty and the METL Limited Warranty this Emissions Control Warranty shall apply except where the METL Limited Warranty may provide a longer warranty period YOUR WARRANTY RIGHTS AND OBLIGATIONS State of California The California Air Resources Board and MAT Engine Technologies LLC METL are pleased to explain the emissions control system warranty on your 2009 small off road engine SORE In California new
13. g e Save all instructions PROBLEM POSSIBLE CAUSE S SOLLUTION S Engine will not start Engine will not accelerate lacks power or stalls Engine smokes excessively Engine runs hot Engine will not idle properly Ignition Switch in the OFF position Engine flooded Fuel Tank empty Spark Plug not firing Fuel not reaching carburetor Carburetor requires adjustment 1 Fuel not reaching carburetor Air filter dirty Spark plug fouled Carburetor requires adjustment Carbon build up on muffler outlet screen 6 Compression low 1 Fuel mixture incorrect 2 Air filter dirty 3 Carburetor requires adjustment 4 Choke lever in the CHOKE COLD START position 1 Fuel mixture incorrect 2 Spark Plug incorrect 3 Carburetor requires adjustment 4 Carbon build up on muffler outlet screen 1 Carburetor requires adjustment 2 Crankshaft seals worn 3 Compression low Technical Service SSS eet You may have further questions about assembling operating or maintaining this cultivator If so you can contact our Technical Service Department at 1 800 737 2112 English only You may also write to METL Corporate Office CORRESPONDENCE ONLY ATTN Technical Service METL 6700 Wildlife Way Long Grove IL 60047 1 Move ignition switch to the ON position 2 See Starting a Flooded Engine in OPERATION section 3 Fill tank with correct fuel mixture 4 Replace
14. ge to the owner 5 Notwithstanding the provisions herein warranty services or repair will be provided at all of our distribution centers that are franchised to service the subject engines 6 The engine owner must not be charged for diagnostic labor that leads to the determination that a warranted part is in fact defective provided that such diagnostic work is performed at a warranty station 7 METL is liable for damages to other engine components proximately caused by a failure under warranty of any warranted part 8 Throughout the engine warranty period stated above METL will maintain a supply of warranted parts sufficient to meet the expected demand for such parts 9 Any replacement part may be used in the performance of any warranty maintenance or repairs and must be provided without charge to the owner Such use will not reduce the warranty obligations of METL 10 Add on or modified parts that are not exempted by the Air Resources Board may not be used The use of any non exempted add on or modified parts by the original or subsequent purchaser will be grounds for disallowing a warranty claims METL will not be liable to warrant failures of warranted parts caused by the use of a non exempted add on or modified part 11 The manufacturer issuing the warranty shall provide any documents that describe that warranty procedures or policies within five working days or requested by the Air Resources Board Questions Call Toll F
15. gine is first purchased The warranty period is two years b Subject to certain conditions and exclusions as stated below the warranty on emissions related parts is as follows 1 Any warranted part that is not scheduled for replacement as required maintenance in your Operator s Manual is warranted for the warranty period stated above If the part fails during the period of warranty coverage the part will be repaired or replaced by METL according to Subsection 4 below Any such part repaired or replaced under warranty will be warranted for the remainder of the period 2 Any warranted part that is scheduled only for regular inspection in your Operator s Manual is warranted for the warranty period stated above Any such part repaired or replaced under warranty will be warranted for the remaining warranty period 3 Any warranted part that is scheduled for replacement as required maintenance in your Operator s Manual is warranted for the period of time before the first scheduled replacement date for that part If the part fails before the first scheduled replacement the part will be repaired or replaced by METL according to Subsection 4 below Any such part repaired or replaced under warranty will be warranted for the remainder of the period prior to the first scheduled replacement point for the part 4 Repair or replacement of any warranted part under the warranty provisions herein must be performed at a warranty station at no char
16. han 10 ethanol or methanol Use 2 cycle oil that meets or exceeds JASO FC specifications and is intended for mixing at a fuel to oil ratio of 40 1 Use of incorrect gasoline such as diesel fuel or gasoline containing more than 10 ethanol or methanol will damage the cultivator engine and void your warranty Use of incorrect oil such as automotive oil 2 cycle marine outboard oil or any oil other than specified oil will damage the cultivator engine and void your warranty To mix the fuel and 2 cycle oil follow instructions on 2 cycle oil container for mixing fuel Mix gasoline and 2 cycle oil at a ratio of 40 1 A mixture with a 40 1 ratio is obtained by mixing 1 gallon 4 liters of gasoline with 3 2 ounces of oil 95 ml After adding oil to gasoline shake container momentarily to ensure proper mixing IMPORTANT Mix only enough fuel for your immediate needs Do not store pre mixed fuel B Adding Fuel to Cultivator Stop engine and allow it to cool before refueling ROD Avoid spilling fuel or oil Wipe up all fuel spills Place the unit upright on the ground or on a sturdy bench and wipe and any debris from around the fuel cap Remove fuel cap slowly and use a funnel to pour the mixture into the tank and replace the fuel cap 5 Move at least 10 feet 3 meters away from fueling site before starting engine Starting Engine Starting a Cold Engine 1 Place the cultivator on a flat surface 2 Move
17. if children or bystanders are present Keep hands feet and clothing away from rotating tines Contact with rotating tines may result in serious injury Choke Control Run Warm Start Fuel Mixture Unleaded Goa Cycle Oil Caution Do Not Use Gas Mix with More Than 10 Methanol or Ethanol Choke Cold Start Fuel Primer Press 6 times THROTTLE CONTROL SLOW Ignition Switch ON RUN OFF STOP Safety Alert Symbols This equipment can throw small objects at high speed causing personal injury Inspect area where used and remove all foreign objects Engine exhaust contains carbon monoxide an odorless and deadly gas NEVER run unit indoors or in a poorly ventilated area To reduce risk of fire clean spilled gas and oil and keep unit free from debris Gasoline is extremely flammable Allow machine to cool completely before refueling Extremely hot surface Do not touch a hot muffler gear box or cylinder you may get burned These parts get extremely hot from operation and remain hot for a short time after the unit is turned off Fuel Mixture 40 1 Unleaded Gas 2 Cycle Oil Throttle Control SLOW FAST The information listed below should be read and understood by the operator We utilize the symbols below to allow the reader to recognize important information about their safety A DANGER A WARNING Indicates an imminently hazardous situation which if not avoided will result in death or
18. ing outside d Always wear protective hair covering to contain long hair 5 Always wear a face or dust mask if operation is dusty 6 Always wear eye protection that meets or exceeds the requirements of ANSI Z87 1 7 Always wear hearing protection which meets or exceeds ANSI standards 8 Thoroughly inspect the area where the cultivator is to be used and remove all foreign objects 9 Keep the area of operation clear of all persons particularly small children and pets A WARNING Your equipment can throw small objects at high speed causing personal injury or property damage 10 Never allow children to operate the equipment Never allow adults to operate the equipment without proper instruction 11 Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people their property and themselves A WARNING Engine exhaust from this product contains chemicals known to the State of California to cause cancer or birth defects or other reproductive harm While Operating Cultivator Stay alert Use common sense Watch what you are doing Do not operate cultivator if it is damaged or not securely and fully assembled Never operate the cultivator without good visibility or light Never operate the machine without proper guards plates or other safety protective devices in place Keep all part of your body away from the rotating tines Do not put hands or feet near or under rotating parts
19. ndle Bolt Throttle Trigger 1 Place the cultivator upright with tines and wheels on a hard level surface Wheels should be set in the lowest position A WARNING Do NOT place the cultivator on a high surface where it can fall and cause property damage or personal injury 2 Assemble the middle handle to the lower handle with the 2 bolts and wing nuts Refer to Figure 1 Firmly hand tighten the wing nuts 3 Attach the upper handles to the middle handle using the two remaining bolts and wing nuts Refer to Figure 1 4 Assemble the ignition switch and throttle trigger to the right upper handle with the screw Use included wrench See Figure 1 5 Make sure the ignition wire is connected to both the ignition switch on the upper handle and the engine Make sure the wires are connected at the white connection terminal 6 Use the cable ties to secure the throttle cable and ignition wire to the handles 7 The drag stake is shipped with the point facing upwards To use for cultivating remove detent pin and turn the drag stake upside down so the point faces downward Re insert the detent pin Refer to Figure 2 Questions Call Toll Free at 1 800 737 2112 5 Copyright 2009 MAT Engine Technologies LLC Assembly Continued e Save all instructions How to Assemble the Tines
20. nt pin through the holes to secure the drag stake Note For the deepest cultivating depth set the drag stake in its lowest position This will give the greatest resistance and allow for the deepest depth Detent Pin Support Bracket H Engine Break In Period Adjusting the Wheel Height 1 Slide the spring loaded sleeve toward the wheel See Figure 12 2 Move the wheels up or down NOTE the upper position is for cultivating the lower position is for transport 3 When the wheels are in either the upper or lower position allow the spring loaded sleeve to slide into the assembly to lock the wheels in position k ee d Sleeve 3 4 SS Pull Sleeve outward m o adjust ri During the first ten 10 hours of use use the slowest engine speed which allows for effective cutting and avoid operation at high engine speeds for extended periods of time This will maximize the life and performance of your cultivators engine Maximum power will be achieved after the first ten 10 hours of engine operation Questions Call Toll Free at 1 800 737 2112 Copyright 2009 MAT Engine Technologies LLC Maintenance e Save all instructions A WARNING Turn off ignition switch and disconnect the spark plug before performing maintenance except for carburetor adjustments Reconnect the spark plug wire after the service is done A Air Filter Your cultivator has been equipped with two 2 foam air filters inside the air filter
21. part fails during the period of warranty coverage it must be repaired or replaced by METL issuing the warranty Any such part repaired or replaced under the warranty must be warranted for a time not less than the remaining warranty period 2 Any warranted part that is scheduled only for regular inspection in the written instructions must be warranted for the warranty period defined in subsection b 2 A statement in such written instructions to the effect of repair or replace as necessary will not reduce the period of warranty coverage Any such part repaired or replaced under warranty must be warranted for a time not less than the remaining warranty period 3 Any warranted part that is scheduled for replacement as required maintenance in the written instructions must be warranted for the period of time prior to the first scheduled replacement point for that part If the part fails prior to the first scheduled replacement the part must be repaired or replaced by METL Any such part repaired or replaced under warranty must be warranted for a time not less than the remainder of the period prior to the first scheduled replacement point for the part 4 Repair or replacement of any warranted part under the warranty provisions of this article must be performed at no charge to the owner at a warranty station 5 Notwithstanding the provisions of subsection 4 above warranty services or repairs must be provided at distribution centers that a
22. ranty Continued e Save all instructions California Evaporative Emission Control Warranty Statement YOUR WARRANTY RIGHTS AND OBLIGATIONS The California Air Resources Board and METL are pleased to explain the evaporative emission control system s warranty on your 2009 model year small off road engine SORE In California new SOREs must be designed built and equipped to meet the State s stringent anti smog standards METL must warrant the evaporative emission control system on your SOREs for the period of time listed below provided there has been no abuse neglect or improper maintenance of your SOREs Your evaporative emission control system may include parts such as carburetors fuel tanks fuel lines fuel caps valves canisters filters vapor hoses clamps connectors and other associated components Manufacturer s Warranty Coverage This evaporative emission control system is warranted for two years If any evaporative emission related part on your equipment is defective the part will be repaired or replaced by METL Owner s Warranty Responsibilities e As the SORE owner you are responsible for performance of the required maintenance listed in your owner s manual METL recommends that you retain all receipts covering maintenance on your SOREs but METL can not deny warranty solely for the lack of receipts e As the SORE owner you should however be aware that METL may deny you warranty coverage if
23. re franchised to service the subject engines or equipment 6 The owner must not be charged for diagnostic labor that leads to the determination that a warranted part is in fact defective provided that such diagnostic work is performed at a warranty station 7 Throughout the evaporative emission control system s warranty period set out in subsection b 2 METL issuing the warranty must maintain a supply of warranted parts sufficient to meet the expected demand for such parts 8 Manufacturer approved replacement parts must be used in the performance of any warranty maintenance or repairs and must be provided without charge to the owner Such use will not reduce the warranty obligations of the manufacturer issuing the warranty 9 The use of any add on or modified parts will be grounds for disallowing a warranty claim made in accordance with this article The manufacturer issuing the warranty will not be liable under this Article to warrant failures of warranted parts caused by the use of an add on or modified part 10 METL issuing the warranty shall provide any documents that describe the warranty procedures or policies within five working days of request by the Executive Officer Evaporative Emission Warranty Parts List 1 Fuel Tank Questions Call Toll Free at 1 800 737 2112 16 Copyright 2009 MAT Engine Technologies LLC
24. ree at 1 800 737 2112 13 Copyright 2009 MAT Engine Technologies LLC Warranty Continued e Save all instructions Emission Warranty Parts List The repair or replacement of any warranted part otherwise eligible for warranty coverage may be excluded from such warranty coverage if METL demonstrates that the engine has been abused neglected or improperly maintained and that such abuse neglect or improper maintenance was the direct cause of the need for repair or replacement of the part That notwithstanding any adjustment of a component that has a factory installed and properly operating adjustment limiting device is still eligible for warranty coverage The following emissions warranty parts list is covered 1 Fuel Metering System 4 Catalytic Muffler Assembly if so equipped including a Gasoline carburetor assembly and its internal a Muffler gasket components if So equipped b Exhaust manifold b Fuel filter if so equipped c Carburetor gaskets d Fuel pump if so equipped 5 Crankcase Breather Assembly including a Breather connection tube 6 Miscellaneous items Used in Above Systems including a Switches b Hoses belts connectors and assemblies 2 Air Induction System including a Intake pipe manifold b Air cleaner 3 Ignition System including a Spark plug b Ignition module coil Questions Call Toll Free at 1 800 737 2112 14 Copyright 2009 MAT Engine Technologies LLC War
25. see Product Specifications 4 Clean carbon deposits If excessive carbon build up replace spark plug 5 Adjust the spark plug gap to 0 024 0 028 in 0 6 0 7mm 6 Install the spark plug finger tight in the cylinder head and then tighten firmly with the spark plug wrench 7 Re install the insulated spark plug boot Storage E T LSE 1 Allow engine to cool and empty the fuel tank before storingor 4 When preparing the cultivator for storage or when transporting in vehicle Use up remaining fuel in the carburetor cultivator will not be used for 30 days or more by starting the engine and letting it run until it stops a Empty fuel tank and use up remaining fuel in the 2 When not in use store cultivator indoors in a dry location e i Starting the engine and letting it run Store cultivator above the reach of children or in a locked ahaa oll of ihe reach ot children b Inspect and clean the cultivator thoroughly c Lightly oil all external metal surfaces 3 Store unit and fuel in area where fuel vapors cannot d Remove the spark plug place a few drops of reach sparks or open flames from water heaters electric 2 cycle engine oil into the cylinder Pull the recoil motors or switches furnaces etc starter several times to distribute the oil Replace the spark plug e Inspect and clean air filter as required Questions Call Toll Free at 1 800 737 2112 9 Copyright 2009 MAT Engine Technologies LLC Troubleshootin
26. serious injury Indicates a potentially hazardous situation which if not avoided could result in death or serious injury Indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury A CAUTION or equipment property damage Questions Call Toll Free at 1 800 737 2112 1 Copyright 2009 MAT Engine Technologies LLC Important Safety Information e Save all instructions Before Operating Cultivator 1 READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE OPERATING CULTIVATOR Be thoroughly familiar with the controls and the proper use of the equipment Know how to stop the unit and disengage the controls quickly A WARNING Read and follow all warnings and safety instructions Failure to do so can result in serious injury to you or bystanders 2 Avoid Dangerous Environments a Do not operate cultivator while under the influence of alcohol medications or drugs b Do not operate cultivator when you are tired C Do not use this cultivator if you are mentally or physically unable to operate safely 3 Inspect cultivator for damaged parts and make sure all fasteners and guards are in place and secure Replace any damaged parts 4 Dress properly when operating cultivator a Always wear heavy long pants boots gloves and a long sleeve shirt b Do not wear loose clothing or jewelry that can get caught in the moving parts of the cultivator c Always wear gloves and substantial foot wear when work
27. the ignition switch to the on position See Figure 6 3 Move the choke lever to the cold start position See Figure 7 4 Press the primer bulb slowly 6 times See Figure 8 5 Grab the recoil starter handle with your right hand and support the cultivator with your left hand See Figure 9 6 Pull the recoil starter handle sharply until the engine starts and runs 7 After engine starts and runs for 10 15 seconds move choke lever to run warm start position See Figure 7 RUN WARM START lt gt COLD START Questions Call Toll Free at 1 800 737 2112 Starting a Warm Engine 1 Place the cultivator on a flat surface 2 Move the ignition switch to the on position See Figure 6 3 Move the choke lever to the run warm start position See Figure 7 4 Grab the recoil starter handle with your right hand and support the cultivator with your left hand See Figure 9 5 Pull the recoil starter handle sharply until the engine starts and runs Copyright 2009 MAT Engine Technologies LLC Operation Continued e Save all instructions Starting Engine Continued Starting a Flooded Engine 1 Place the cultivator on a flat surface 2 Move the ignition switch to the ON position 3 Move the choke lever to the run warm start position see Figure 7 4 Hold the throttle trigger fully depressed in fast position See Figure 10 5 Pull the recoil starter handle repeatedly
28. ty applicable is our standard written warranty We make no other warranty expressed or implied MAT Engine Technologies LLC warrants this Cultivator and any parts thereof to be free from defects in material and workmanship for two years 90 days for reconditioned unit from the date of first purchase from an authorized dealer provided that the product has been properly maintained and operated in accordance with all applicable instructions This warranty is extended only to the original retail purchaser The bill of sales or proof of purchase must be presented at the time a claim is made under this warranty This warranty does not cover commercial industrial or rental usage nor does it apply to parts that are not in original condition because of normal wear and tear or parts that fail or become damaged as a result of misuse accident lack of proper maintenance tampering or alteration Travel handling transportation and incidental costs associated with warranty repairs are not reimbursable under this warranty and are the responsibility of the owner To the full extent allowed by the law of the jurisdiction that governs the sale of the product this express warranty excludes any and all other expressed warranties and limits the duration of any and all implied warranties including warranties of merchantability and fitness for a particular purpose to two years from the date of first purchase and MAT Engine Technologies LLC s liability is hereby limit
29. uel a running engine 6 Stop engine and allow to cool before removing fuel cap Remove fuel cap slowly 8 Never store engine with fuel in the tank indoors Fuel and fuel vapors are highly flammable 9 Replace all fuel tank and container caps securely uoneunojuj Ajajesg jueyoduiy Maintenance amp Storage of Cultivator 1 Stop the engine and disconnect the spark plug before servicing cleaning or performing maintenance on the unit Never attempt to make any adjustments while the engine is running 2 Maintain cultivator with care Inspect cultivator periodically Keep machine attachments and accessories in safe working condition If cultivator is not working properly or damaged have it repaired by a qualified service center 3 Check for misalignment of moving parts binding of moving parts broken parts and any other condition that may affect its operation Check shear bolts engine mounting bolts and other bolts at frequent intervals for proper tightness to be sure the equipment is in safe working condition 4 Keep guards in place and in working order 5 A guard or other part that is damaged should be properly repaired or replaced by a qualified service center 6 Use only genuine Southland replacement parts and accessories Use of any non Southland parts or accessories could lead to injury damage the unit and void your warranty 7 Do not remove or modify any parts Removing or modifying parts could lead to injury damag
30. your SOREs or a part have failed due to abuse neglect or improper maintenance or unapproved modifications e You are responsible for presenting your SOREs to distribution center or service center authorized by METL as soon as the problem exists The warranty repairs should be completed in a reasonable amount of time not to exceed 30 days If you have any questions regarding your warranty coverage you should contact METL customer service If you need assistance or have any questions CALL TOLL FREE 1 800 737 2112 Questions Call Toll Free at 1 800 737 2112 15 Copyright 2009 MAT Engine Technologies LLC Wa rra nty Continued e Save all instructions Defects Warranty Coverage a The warranty period begins on the date the engine is purchased b General Evaporative Emissions Warranty Coverage The engine must be warranted to the ultimate purchaser and any subsequent owner that the evaporative emission control system when installed was 1 Designed built and equipped so as to conform with all applicable regulations and 2 Free from defects in materials and workmanship that causes the failure of a warranted part for a period of two years c The warranty on evaporative emissions related parts will be interpreted as follows 1 Any warranted part that is not scheduled for replacement as required maintenance in the written instructions must be warranted for the warranty period defined in subsection b 2 If any such
Download Pdf Manuals
Related Search