iTronics® Installation Instructions
Contents
1. the fuse with end red wire power cable and insert back into original position TG i MLD U 3 Connect end black wire of UPC to the any metal part of the vehicle that is grounded check for 12V with your multimeter from to If there is no screw attached to the vehicle you must screw one on the vehicle make sure the connection is secure and not loose Note The unit will not work if the black wire is not properly connected to ground on the car metal chassis 4 Make sure the product is working properly after the vehicle engine is started when the ignition is on and then arrange and hide the cables for neat installation Note When UPS is connected please check your SD on a regular basis Extend the life of your SD card by formatting it more than once a week ITRONICS VIDEOS2. Installation Guide 78 500HD t PASS By BLACK S L ECH SECURITY gt m s s BY BLACK Vehicle Driving Recorder iITRONICS Components ip ASS y BLack S LIECH 16 S Main unit Camera 2EA Mounting cradle Adhesive tape Adhesive tape 2EA for camera unit for main unit card Spare 2EA 2EA SD card reader Cable holder User manual Remote Remote Option IR sensor Option Camera AV cable Camera External GPS Cigar Jack Connecting Cable Connecting Cable Option Power Cable 5M x 2EA 7M Option Option Name of the product details PASS Bje ack S LIECH SECURITY Main unit front Power on off switch Power on LED indicator Low battery warning LED indicator GPS status indicator BOD SD memory card slot Main unit back Front camera port Rear camera port IR receiver port AV cable port External GPS port Power cable input port Camera Cable input port LED indicator Camera Lens Mic on off short key Self format button long key ao OOO Installation tP ASS B BLack S LIECH SECURITY PLEASE NOTE IT IS RECOMMENDED TO CHECK THE PRE INSTALLATION TEST i e connecting the power from the fuse boxes to the devices in a casual manner BEFORE THE INSTALLATION 1 Assemble the camera with mounting cradle and fix it to the window shield Clean the window shield before f
3. complete When the external GPS receiver is installed please make the GPS receiver face up to the sky and fully exposed through the windshield Then put the GPS received cable into the GPS port of main unit t P AS S By BLACK S L ECH SECURITY Type Images Specifications Power Cable 1 VCC 2 RX GPS Cable 199 3 TX GPS Signal Output 4 GND EE 1 2 PD l PRE HH 2 1 2 GND i l YCC 2 Data D Camera Cable I 3 Data D 4 GND ie 1 VCC Remote IR Sensor Cable 1 II 2 Data IN _ 3 GND How to connect power teas sg Bract S LIECH This product is available to be connected with Uninterrupted Power Cable UPC for using the product as a surveillance camera when the vehicle engine is stopped However when you connect UPC you are highly recommended to use our authentic UPC which has battery protection circuit in order to prevent the vehicle battery from discharging 1 Open fuse box inside of the vehicle and by using electric testing device such as a multimeter find the permanent fuse which the power constant 12V is supllied when the engine is off For example emergency flasher lights interior lights and door lights etc 2 Pull out the fuse and connect one leg of
4. ixing it 2 Put the connecting cable into the camera port of main unit and connect it with each of the camera Please install two cameras Front and Rear in the same way as above procedure Put the power cable into the power port and connect it with car battery fuse box The product requires constant 12V 24V DC power supply While the power is turned off insert the SD memory card into the slot of main unit Check all connections and power on the unit for operation to run a TEST to make sure the system is functioning properly After the test is complete you can continue to mount the main control unit and arrange cameras see next page Installation tP nS S Biack S LIECH SECURITY 7 Fix the main unit to a suitable accessible location with some ventilation Use the provided 3M tape or mount with screws so the install is secure 8 Align the direction of the camera lens to the front Please refer to the camera alignment guide arrow mark printed on each camera 9 Connect the GPS receiver optional to the correct port on the main control unit and mount receiver so it has a clear view of the sky do not mount behind dark tint strips or close to metal 10 Arrange all cables with cable holders to provide a neat installation Check all connections at the main control unit to ensure all the correct ports have been used 11 Power on the unit for normal operation Installation is now
Download Pdf Manuals
Related Search