Home

Instruction Manual - Pdfstream.manualsonline.com

1. E 5 EVENT SEARCH Baa BEGIN END 05 01 15 15 00 01 05 01 15 15 00 06 gt 01 ALARM 2005 01 15 02 MIX 2005 01 15 03 TIME 2005 01 15 04 ALARM 2005 01 15 PRESS lt gt THEN ENTER PRESS MENU TO EXIT 1 EVENT SEARCH Displays all recording events every page consists of 7 events and maximum 63 stored events 2 Press PLAY button to play the selected event BEGIN END 05 01 15 15 00 01 05 01 15 15 00 06 Displays the beginning and end time of each event CV0104DVR 22 a New You Can See 5 7 HARD DRIVE SETUP HDD DRIVE SETUP gt DISK FULL OVERWRITE MASTER HDD SIZE 120103MB MASTER HDD USED 120103MB 100 MASTER HDD FORMAT SLAVE HDD 120103MB SLAVE HDD USED 13321MB 11 SLAVE HDD FORMAT PRESS lt gt THEN ENTER PRESS MENU TO EXIT 1 When item OVERWRITE has been selected press ENTER to enable overwrite when both MASTER or SLAVE HDD is full 2 options OVERWRITE or STOP 2 MASTER HDD displays the capacity of the MASTER HDD 3 MASTER HDD USED displays the capacity of the MASTER HDD already used 4 SLAVE HDD displays the capacity of the SLAVE HDD 5 SLAVE HDD USED displays the capacity of the SLAVE HDD already used N A indicates HDD not installed or unable to be detected CV0104DVR 23 New You Can See 5 7 1 FORMAT PASSWORD INPUT
2. CV0104DVR 5 ____ New You Can See 4 OPERATING PROCEDURE 4 1 POWERING ON This DVR is built to be on at all times and therefore should be connected to a surge protected power bar UPC power backup Use the power bar s switch to turn the unit off and on This is especially important as loss of power while recording could possibly damage the hard drive Every time the DVR is powered on it will auto detect its peripherals self testing warm up auto detects the hard drive etc It will also detect all video input signals If it does not detect an input eg no camera present it will sound an alarm Press any button on the DVR to stop the alarm There are 4 camera inputs and channels Disable the unused channels in the Camera Setup Menu to prevent the alarm from activating every time the unit is powered on 4 2 MONITORING MODE Monitoring mode is the default mode after the DVR is powered on It will display all 4 camera views To display a specific camera press the corresponding number This will place that camera s view on your entire screen To display all cameras again press the Quad Display button To start recording press REC To stop recording press STOP To reset all DVR settings to their factory default settings under quad or single display press the PAUSE button 5 times The message ALL SETTING DATA IS INITIALIZED will be displayed and after the reset the default password will be set as 111111 When
3. 1 When proceeding FORMAT function the above display will be shown 2 When password entered is correct the screen will display the message PASSWORD CORRECT HDD FORMATTED flashes 3 times indicating hard disk format is successful 3 When password entered is incorrect the screen will display PASSWORD INCORRECT flashes 3 times and return to HARD DRIVE selection Once the user formats the hard disk drive MASTER the camera title returns to its default setting CAMERA1 CAMERA2 CAMERA3 CAMERA4 because this setup is stored in the hard disk drive MASTER CV0104DVR 24 a Aa New You Can See 6 NETWORK REMOTE CONTROL OPTIONAL 6 1 NETWORK DVR SETUP Connect the RJ 45 cable to the network port on the back of the DVR and the other end to your router Use IPEdit exe to test the DVR The network access software is not MAC compatible It is only compatible with a Windows PC running using the Internet Explorer browser Note Before using PPPoE and DDNS recommended connection method you must first setup an IP Address using IPEDIT exe 6 1 1 ONLINE WITH DHCP SERVER Use IPEDIT exe to find the installed Network DVR Select this Network DVR in the Camera List Window The default configuration will be shown on the right window Update the IP status IPEdit 3 Camera lists LenCamera 92 168 10 25 Nane TenCamera 0000 Gateway 192 168 10 254 IP 192 168 10 25 Netmask 255 255 255 0 HTT
4. In the Finish Port field enter the ending port number e g 80 Check the Apply buttonNext in the Security option select Rules Next in the Rules screen select Add in the inbound services Next in the Inbound services proceed as follows In the Service drop down list select the newly created DVR entry In the Action field select ALLOW always In the Send to LAN Server field enter your computers IP address In the WAN Users field set to Any In the Log field set to Never Click on Apply Port forwarding is now complete 7 NETOPIA ROUTER The port forwarding process may vary depending on the brand and model number of the router being used Port forwarding of a router is required to allow user access to your network device Regardless of the Netopia router being used the process of port forwarding is similar You will need to enable the ports by locating the port range forwarding screen The set up instruction outlined below is an example of port forwarding a Netopia Router using Netopia Model 3346 Step 1 Open your web browser Enter the router IP address 192 168 62 1 in the address bar as shown below followed by pressing Enter Step 2 Enter admin in the User Name and 1234 in the Password dialog box followed by OK to enter the Netopia configuration page Step 3 Select Expert Mode Step 4 Select the Yes enter expert mode button Select Configure followed by selecting NAT Step 5 Select the D
5. 9 C Reset Lx J Security Settings 8 Initialize and script Activex controls not marked as safe Disable O Enable Of 4 Activex controls and plug ins Administrator approved Disable Enable Prompt Script Activex controls marked safe For scripting Disable Enable Prompt 1 4 Reset to Medium v Reset Change ActiveX settings to the ones seen above CV0104DVR 29 RON New You Can See The graphic below will be shown the first time you install the ActiveX Control Please select Yes to accept installation 5 curity Warning Do you want to install and nan http 7192 158 0 245 Oliw rw ebPush cab The publisher be determined due to the problems below Authenticods signature nct ford Download ActiveX Control Live view will be displayed when installation is successful AED hitp 4 192 168 1 222 re rose FERES a ZUR HEN E INNRE BEN ESANAC Live display under ActiveX mode CV0104DVR 30 ee Now You Can See 6 3 MAIN DISPLAY Remote control DVR Main Menu 1 Live display 2 DVR control button 3 Video setup 4 Configuration Enter detail setup Recording Displays recording setup menu for video recording Snapshot Pop up window displays live images right mouse click to save No
6. Adapter Input AC 100 250V 50 60Hz aolo MaLo M Fan Based Operating Environment ence 41 F 104 F ali 30 80 DIMENSIONS ciere tina 12 6 x 1 8 x 10 6 Weight 6 6165 without HDD CV0104DVR 52 a New You Can See SVAT SUPPORTS CRIME STOPPERS Crime Stoppers programs are operated as non profit charities and are managed by a volunteer board of directors who raise funds and pay rewards to individuals who anonymously call with information that helps solve crime Rewards are paid for tips that lead to the arrest and indictment of people charged with felony offences and to date Crime Stoppers statistics show a conviction rate of approximately 95 To receive more information about Crime Stoppers or to make a charitable donation please fill in the fields on the back of this page cut on the dotted line and mail in Shu aor a m o o gc D x a lt O CRIME STOPPERS INTERNATIONAL CV0104DVR www svat com gt O New You Can See SVAT SUPPORTS CRIME STOPPERS To receive more information about Crime Stoppers or to make a charitable donation please fill in the fields below cut on the dotted line and in CRIME STOPPERS INTERNATIONAL Crime Stoppe
7. PRESS MENU TO EXIT To setup LANGUAGE SET function press ENTER to select the desired language languages supported are Chinese and English CV0104DVR 14 New You Can See 5 3 CAMERA SETUP CAMERA SETUP gt CAMERA ENABLE CAMERA TITLE CAMERA SETTING CH1 TITLE CH2 TITLE CH3 TITLE CH4 TITLE PRESS lt gt THEN ENTER PRESS MENU TO EXIT 1 Camera Enable Select this option to change the camera view combination For example if you select all camera channels will be disabled and a black screen will be displayed If you select 1 2 3 4 all cameras channels will be enabled and displayed If you select 4 only the camera 4 channel will be enabled and displayed Use the ENTER button to change these combinations Note Disable the camera channels that you won t be using or the VIDEO LOSS alarm will sound during startup and recording 2 Camera Title Select this option to change whether you want a custom title displayed for each camera for no cameras or for some cameras Use the enter button to select the combination to your preference 3 Camera Setting Allows you to change specific settings for each camera Please refer to the next section for more details 4 CH 1 4 Title Select a camera and use the up down and ENTER buttons to change the title maximum 8 characters When you are finished press MENU to confi
8. add a new user defined application Step 5 Select the Back button to return to the Edit Firewall Screen In the Edit Firewall Settings proceed as follows In the Application Name field type DVR In the Protocol selection select TCP In the Port field enter in the first box the first number of the port you need to port forward e g 80 and in the second box the ending port number e g 80 Select the Add Definition button Step 6 In the Edit Firewall Settings proceed as follows In the Select a Computer field select DVR In the Edit a Firewall Setting check the Allow Individual Applications box and highlight the DVR application which you just created Click Add Finally select the Done button at the bottom of the screen Port forwarding is now complete CV0104DVR 50 a New You Can See 10 DVR SPECIFICATIONS FUNCHONAlILY entente cepe Simplex Video Compression Modified MJPEG FROSOMUDIOMIN esce TE 720 x 480 Recording Frame Rate ecce Max 120 FPS Recording TIME uii Max 60 days 15 days with 4 cameras RESOlUTIOD 5 ecc cds 640 224 5 2 orci oce tete Dente een Low Medium High Modes dete ukane Manual Schedule Motion Detection Method Quad Each Recording Media 1 x 3 5 80GB IDE HDD Max 500GB Video
9. change the playback speed FF1 FF2 FF3 or press the REW button to reverse playback CV0104DVR 7 New You Can See 5 SYSTEM SETUP 5 1 MENU 1 2 3 gt SYSTEM SETUP CAMERA SETUP RECORD SETUP BUZZER SETUP EVENT LIS HARD DRIVE SETUP 4 PRESS lt gt THEN ENTER PRESS MENU TO EXIT 1 Main Menu 2 Menu Layer Indication The device consists of four menu layers El First Menu Layer Main Menu Second Menu Layer BEN Third Menu Layer BERN Fourth Menu Layer 3 Menu Operation and Setup Press the up or down button to move the cursor gt Press the ENTER button to enter the sub menu Press MENU button Under the second or third menu layer the system will return to the previous menu layer second layer to first layer or third layer to second layer and will auto update the modified data Under main menu first menu layer the system will enter live mode Press ENTER to increase or decrease the highlighted setting values 4 Menu Layer Operation Guide CV0104DVR 8 New You Can See 5 2 SYSTEM SETUP SYSTEM SETUP gt TIME SET PASSWORD SET LOARD DEFAULT LANGUAGE SET ENGLISH VERSION V1 2 PRESS THEN ENTER PRESS MENU TO EXIT 1 Cursor gt position indicates the current function selected 2 Press the up and down buttons to move the cursor 3 Press ENTER button to proceed 4 Pres
10. in WindowsXP ENG D jJ OF Mm m 2 Documents and Settings Program Files M Recent wINDOWS ocuments rj 1 ipg 3 Bin 3 Desktop 1 15 S application set bmp IN mys bmp N mys_file bmp pc viewer bmp recording bmp N snapshat bmp Upgrate bin File name Juparate M Files of type Al Files 7 Select the Firmware to be Updated Select software Upload Uploading the Selected Firmware CV0104DVR 39 T E Now You Can See Itis strongly recommended to stop any unnecessary jobs while updating firmware Please be patient and the updating process may take a long time cio here to begin to update firmware 9 to ignore and delete the file uploaded just now Firmware Update Press here button 1 to update Firmware Press here button 2 to delete the file The message below displays the writing progress of the firmware update When Firmware update is completed it will show 100 and a message Click here to reboot DVR browser will be displayed requesting to restart the Network DVR ktis strongly recommended to stop any unnecessary jobs while updating fimo ware Please be patient and the updating process may take a long time kere to begin to update firmware Cie bere to ignore and delete the file uploaded just now Writing Progress 34 Firmware Update Display It is strongly recommended to stop any unn
11. the reset is completed the message DVR RESET COMPLETED TURN OFF AND ON THE DVR will be displayed Restart the DVR to continue 4 3 RECORD MODE VIDEO LOSS OFF EACH REC M T 2004 06 06 12 12 12 55 2 CV0104DVR 6 a New You Can See Note CH1 No block figure next to CH1 indicates that it is not recording EACH Record Type QUAD Record Type M MASTER HDD T TIMER RECORD A ALARM RECORD M MIX RECORD 0 Currently under recording VIDEO LOSS Video input unable to be detected CAMERA Title for CH 1 OFF Channel is set to OFF 4 4 PLAYBACK MODE TIME SEARCH HARD DRIVE MASTER 03 11 27 18 20 42 03 11 27 19 32 32 gt 01 TIME 2003 11 27 18 20 42 02 TIME 2003 11 27 16 43 56 03 TIME 2003 11 27 15 07 11 lt gt MOVE ENTER CHANGE PLAY PLAY MENU EXIT FF SELECT EVENT OR TIME gt 01 TIME Total 7 gt 07 To play your recordings press PLAY A list of your recordings will appear after a slight delay Use the up and down arrows to find the date and time of your recording The date format is YY MM DD Year Month Day Press PLAY again to begin playback In playback mode you can also choose to view all 4 of your cameras or an individual camera if you have recorded in EACH mode When the recording is done press STOP to return to live mode During playback press FF to
12. user to the A presence of important operating maintenance servicing instructions in the literature accompanying the appliance WARNING TO PREVENT FIRE OR SHOCK HAZARDS DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE CV0104DVR www svat com a New You Can See TABLE OF CONTENTS WHAT IS NGL UID DD 2 e adde eu ceto acuto 1 WHAT IS COMPATIBLE 1 SAFETY 2 INTRODUCTION FEATURES 3 INSTALLATION 4 NAME 8 FUNCTION OF EACH 5 OPERATING PROCEDURE 2 6 7 SYSTEM SETUP e BOR al eine dine 8 24 NETWORK REMOTE CONTROL OPTIONAL 25 40 TROUBLESHOOTING 41 42 GLOSSARY 43 PORT 44 50 SPECIFICATIONS scie 51 52 WHAT IS INCLUDED 4 Window Warning Stickers zadi Mounting Hardware ee 1 Year Warranty Instruction Manual 1x 4CH DVR 5x BNC Connectors 1x Ee Power Online Toll Free Tech Support RCA to RCA RJ a wire male installa i CD WHAT IS COMPATIBLE The CVO104DVR is compatible with TVs VCRs computers and other SVAT systems including 0 woe Wi CV65 CVP400C CVP403C CVP500C CVP3017M CV0104DVR 1 a New You Can See SAFETY PRECAUTIONS Disposal of Old Electrical amp Electronic Equipment Applicable in the European Union and
13. ADSL PPPoE Router 3 Online using DDNS Server CV0104DVR 26 _____ New You Can See 6 2 1 ONLINE USING Setup similar to 6 1 Network DVR Setup 6 2 2 ONLINE USING ADSL PPPOE ROUTER Setup similar to 6 4 3 3 Connect to ADSL by PPPoE mode 6 2 3 ONLINE USING DDNS SERVER RECOMMENDED The DDNS service provides the dynamic IP to users to gain access to resources connected to the Internet via a cable or DSL connection Once you ve decided to apply this function please register your domain name at http www dyndns org this website supports register free service Paid DDNS service is applied to long term users For more information please refer to 6 4 4 DDNS Setup 6 2 4 ONLINE CONNECTION Note To access the DVR from outside your router s network you will need to forward port 80 to your Network DVR This must be done through your router and the process varies based on your router s make and manufacturer For instructions on port forwarding see the guide at the end of this manual Page 45 Start the Internet Explorer enter the IP Address of the Network DVR into the Address field such as 192 168 1 13 or within IPedit double click on your DVR from the list Before connection User name and Password will be requested Default User Name admin Default Password 1234 Connect to 192 168 1 119 Camera Server User name admin Password Remember my pa
14. Box jaule nsa hinet net Subject IP Camera PPP Dialedi ADSL Setting Display If the Network DVR and ADSL modem are connected by a hub the user can select Dial On Power Up to perform the connect operation However if the Network DVR and ADSL modem are connected directly then please note the following steps below Power off Network DVR Connect Network DVR directly to the ADSL modem using RJ 45 Ethernet port Power up Network DVR Network DVR will start dialing Once connected mail the IP address information to the preset e mail address oa amp After 10 times of connection failure it aborts the operation and the user can reconnect it by LAN to find the cause CV0104DVR 37 4 New You Can See Note If item Send mail after connected is selected then the Network DVR will send a mail that contains the message Dial Up IP Address Netmask Gateway DNS Server will be mailed to the preset e mail address 1 Camere H Dialed Plax Text Be 16 dew pent actin Grey Grad di X 4 0 Sob UB EF 120 net ev PCO JUUn rever 61 25018 284 DS D 166 05 1 Connection Message Send to User 6 4 4 DDNS SETTING RECOMMENDED Press DDNS server connection to start up the function It can autonomously and automatically contact the DDNS provider service whenever the router detects that its public IP address h
15. Image storage according to Save Path Pre Name Image storage according to Prefix Name Save as AVI No Limit Unrestricted image storage continuous Number Image storage according to number Save interval Image storage according to 1 10 second e g Enter 10 then 1 avi file is stored per second Enter 50 then 5 avi files are stored in 5 seconds Size Image storage according to size Frame Rate Image storage according to frame rate Time Image storage according to time Maximum Number of Frame in Each File Image storage according to maximum frame Save Path Image storage according to Save Path Pre Name Image storage according to Prefix Name CV0104DVR 32 aa eee Now You Can See Image Recording DownLoad Select IV Save as JPEG JPEG No Limit C Number ri Frames Saye interval f C Size 090 KBytes C Time 10 Seconds Save Path E Documents and SettingsNsimonlua Save s Pre Name webcam No Limit Frame Rate Number Frames Auto C Size 100 SRE Save interval m Time 10 Seconds Maximum Number of Frame in Each File 500 Save Path ocuments and SettingssimonluM Saveds Pre Name webcam 6 3 5 SAVE CURRENT PICTURE Select to save live images 6 3 6 DVR CONTROL SETUP Supports DVR remote control function Please refer to 6 1 Front Panel Buttons and Controls on page 5 6 3 7 Q
16. P Port1 80 HTTP Port2 8888 MAC 00 00 00 00 00 22 You can change camera name IP address and Gateway Address 1 Select the Camera you want to make change 2 Change name Gateway IP address and Netmask on right edit box 3 Press Submit button or Enter 4 Press Update to rescan the installed IPCams Online with DHCP Server CV0104DVR 25 _____ New You Can See 6 1 2 ONLINE WITHOUT DHCP SERVER STATIC IP 1 Use IPEdit exe to find the installed Network DVR 2 The Internet DVR without IP allocated by DHCP will have a default IP Address of 169 254 1 13 3 Select this Internet DVR on the Camera List Window 4 The default configuration will be shown on the right window 5 Under MSDOS mode enter IPCONFIG to access Geteway IP and Netmask setting values 12 IPEditY3 Camera lists Name 192 1698 1 31 Gateway IP 169 Netmask 255 255 255 0 HTTP Portl 80 HTTP Port2 MAC 00 0D D5 00 34 B0 You can change camera name IP address and Gateway Address 1 Select the Camera you want to make change 2 Change name Gateway IP address and Netmask on right edit box 3 Press Submit button or Enter 4 Press Update to rescan the installed IPCams Online without DHCP Server After the Submit button is clicked the IP information of this Network DVR will be updated 6 2 CONNECTING NETWORK DVR 3 methods for connecting Network DVR 1 Online using Intranet or Static IP 2 Online using
17. Password Delete User Account Current Users Needed No Need Usemame Password Confirm Usemame jiann 1 administrator User Setting Display 6 4 2 1 USER AUTHORIZATION SETTING Select item Needed to enable user authorization function then each time before login to Network DVR the Login window will request for Username and Password disable user authorization function select item No Need CV0104DVR 35 _____ Now You Can See 6 4 2 2 NEW USER CHANGE PASSWORD Enter a new user name and password information to create a new user account or enter an existing user account then set a new password to replace the old password and select OK to create the account or change password After selecting OK button the Current User List would display the newly created user account Maximum 20 users user name and password setup are limited to 10 characters 6 4 2 3 DELETE USER Enter the user account that you wish to delete click OK to delete the account After selecting OK button the selected user account will be deleted from the Current User List 6 4 3 NETWORK SETTING 6 4 3 1 FIXED IP To setup follow the steps below 1 Select item Manually 2 Enter IP Address Subnet mask and DNS 3 Click OK button to save the setting O Manually SibretM
18. UALITY SETTING Network DVR provides 5 image quality settings The user can select the quality setting from the Quality list box e Highest e High Medium Low Lowest CV0104DVR 33 LR New You Can See 6 3 8 RESOLUTION SETTING The network DVR provides six resolution settings The user can select the quality setting from the Resolution list box e 176 x 144 e 160 120 e 320 x 240 352 x 288 640 480 e 704 576 Note The device supports auto video system detection NTSC PAL 6 3 9 ADVANCED SETTINGS Network DVR provides the advanced settings for the following Brightness e Contrast e Saturation Hue 6 4 CONFIGURATION FOR ADVANCED USERS Only the administrator can select the Configuration the ordinary user account does not have this privilege to access this function 6 4 1 SYSTEM SETTING The number on Port 1 and Port 2 may be changed press OK button to save the setting 80 Port pe Port2 9 m Reboot DVR browser Firraware update Restore factory default configuration System Setting Display CV0104DVR 34 ey ee ee New You Can See e Reboot DVR The system needs 30 seconds to reboot the DVR s network Rebooting does not affect hard drive recording Firmware update Please refer to 6 4 5 e Restore Factory Default 6 4 2 USER SETTING e User Authorization Setting e User or Change
19. aa 4 New You Can See Web Ready 4 Channel DVR W 80GB Hard Drive Instruction Manual eee Now You Can See CV0104DVR www svat com a New You Can See PRODUCT WARRANTY amp REGISTRATION Please visit our website at www svat com to apply for your products warranty registration The warranty registration for is located under the support tab on the SVAT website We take quality very seriously This is why all of our products come with a one year warranty from the original purchase date against defects in workmanship and materials If you have warranty or support issues please contact us using any of the following methods SVAT Electronics USA SVAT Electronics Canada Phone 866 946 7828 2315 Whirlpool St Unit 333 4080 Montrose Road Fax 888 771 1701 Nlagara Falls New York Niagara Falls ON Email support svat com USA 14305 Canada L2H 1J9 Website www svat com Warranty Terms 1 SVAT products are guaranteed for a period of one year from the date of purchase against defects in workmanship and materials This warranty is limited to the repair replacement or refund of the purchase price at SVAT s option 2 When service is required the warranty is validated by the submission of a fully completed warranty card 3 This warranty becomes void if the product shows evidence of having been misused mishandled or tampered with contrary to the applicable instruction manual 4 Routine cleaning normal cosmetic and me
20. as changed The router logs on to an account you setup and maintain and updates the account with its latest public IP address You may register at DDNS Server http www dyndns org Follow the instructions on the website to auto detect IP changes and even give your DVR an easy to remember domain name To setup follow the steps below 1 Register at DDNS Server http www dyndns org 2 Apply domain name 3 Click the Enable button Enter Username and Password and the domain name you registered with dyndns org O Enable 9 Disable UserName Password DDNS Setting CV0104DVR 38 Now You Can See After registering the domain name please enter the information supplied by the administrator to the Network DVR DDNS Account Setting Select Enable button to start up DDNS server and press Submit button to save the setting 6 4 5 FIRMWARE UPDATE SVAT may occasionally release newer versions of firmware for your DVR Please check your product at www svat com to ensure you have the latest version When new firmware is supplied you may update to the new version bin file through your PC by following the procedures below 1 In the configuration menu of your network DVR click on Firmware Update 2 Select browse and select the bin firmware file 3 Press Open 3 Press Upload and follow the onscreen instructions Choose file Look
21. ask Default Gateway 0 192 168 1 254 O automatically by DHCP 0 0 0 0 msi 0000 DNS2 0 0 0 0 User Setting Display CV0104DVR 36 S H3 New You Can See 6 4 3 2 DHCP The DHCP is automatically set as the default network setting of the Network DVR When a Network DVR is connected into the LAN it will issue DHCP packets to request an IP address that is dynamically assigned by the DHCP server If it is unable to get a DHCP address the Network DVR will assign a default IP address such as 169 254 1 13 6 4 3 3 CONNECT TO ADSL BY PPPoE MODE To setup follow the steps below 1 After setup rebooting enables automatic connection to ADSL 2 Enter the Username and Password fields with the account and password provided by the ISP 3 If item Send mail after connected is selected the will be automatically sent when connected to the ISP 4 Click OK button to save the settings Note In order to activate the function it is necessary to reboot the device after the setup pppon Save 8 Dial Now 1 V Dial On Power Up Z 89456215 hinet net Username S hinet 2 Password prem 3 V Send mail about new IP after conneeted Mail Server dsf msa hinet met Username jian V Password eoccee Sender s Mail Box jiann hotmail com Receiver s Mail
22. between QUAD and EACH mode QUAD mode will record all four cameras but will not let you view each camera individually during playback EACH mode will record all four cameras and allow you to view each camera individually during playback 2 Video Quality Press ENTER to change between LOW MEDIUM or HIGH video quality Higher quality settings will result in better image clarity but larger file sizes Lower quality settings will result in reduced image clarity but smaller file sizes 3 Frame Rate Options Frame Rate is the number of frames recorded per second 30 frames per second is the maximum and provides smooth video playback Fewer frames per second result in the video being less smooth but smaller in size There are 2 frame rate options in this menu Timer Rec Frame Rate Press enter to set the recording frame rate when the T timer mode is set up under schedule record Motion Rec Frame Rate Press enter to set the recording frame rate when motion or A alarm modes are set up under schedule record Recording frame rates available NTSC 30 15 10 7 5 4 3 2 1 PAL 25 12 8 6 4 3 2 1 CV0104DVR 17 a New You Can See 5 4 1 RECORD MODE RECORD MODE T TIME M TIME MOTION lt MMTTTITTITITITITITITITIT gt 0 3 6 9 12 15 18 21 24 PRESS lt gt THEN ENTER PRESS MENU TO EXIT 1 This menu allows you to set up the preferred type of
23. cating the port range forwarding screen With some DLINK routers the port forwarding screen is located within the Applications and Games or Filters tab in others it is located in the advance tools tab The set up instruction outlined below is an example of port forwarding using DLINK Model DI 524 Step 1 Open your web browser Enter the router IP address in the address bar as shown below 192 168 0 1 followed by pressing Enter Step 2 Enter the user name admin Leave the password blank followed by pressing the OK button Step 3 Select the Advanced tab Step 4 Select the Virtual Server tab In the Name field enter a description of your DVR In the Private IP field enter the DVR IP address In the Protocol field select Both In the Private port enter the port number you need to port forward e g 80 In the Public port re enter the port number you entered in the private port field e g 80 Select the Schedule to Always If more ports are required to be port forwarded repeat the above steps When complete select the Apply button located at the bottom of the page to save your changes Port forwarding is now complete 3 LYNKSYS WIRELESS ROUTER Enable the system by checking the enabled box The port forwarding process is dependant on the brand and model number of the router being used Port forwarding of a router is required with your system to allow user access to your network device Regardless of the Linksys Wireless R
24. chanical wear and tear are not covered under the terms of this warranty 5 The warranty expressly provided for herein is the sole warranty provided in connection with the product itself and no other warranty expressed or implied is provided SVAT assumes no responsibilities for any other claims not specifically mentioned in this warranty 6 This warranty does not cover the shipping cost insurance or any other incidental charges 7 You MUST call SVAT before sending any product back for repair You will be given a Return Authorization number When returning the product for warranty service please pack it carefully in the original box with all supplied accessories and enclose your original receipt or copy and a brief explanation of the problem include RA 8 This warranty is valid only in Canada and the U S A 9 This warranty card cannot be re issued CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE THE COVER BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL Graphic Symbol Explanation alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The lightning flash with arrowhead symbol within an equilateral triangle is intended to The exclamation point within an equilateral triangle is intended to alert the
25. delay while the DVR searches for your recorded files Wait a few moments and your files should appear Make sure you are not in Recording Mode Pressing PLAY during recording will have no effect Press STOP first If you have just formatted your drive or your drive is otherwise empty there will be no files to play back During playback can t switch To switch between cameras during playback you to different camera views must have recorded your file in EACH mode Change this setting using Menu gt Record Setup gt Record Type CV0104DVR 41 a New You Can See Problem Unexpected Alarms beeps Video Loss One of your cameras are go off disconnected There are a few options connect a camera disable that camera s channel if you don t want a camera installed in that channel or disable the VIDEO LOSS alert alarm by going to MENU gt Buzzer Setup gt Video Loss Alert Press enter to disable it HDD Full A buzzer activates when your HDD is full Set the HDD to overwrite to avoid this problem It will record new footage over your oldest footage Go to Menu gt Hard Drive Setup gt Disk Full Press enter to set it to OVERWRITE Alarm Alert may be set to ON which sounds a short alarm whenever motion is detected Go to Menu gt Buzzer Setup gt Alarm Alert and press ENTER to disable it No picture from camera s Make sure all the cameras RCA and power cables are plugged in securely and in their proper places Make sure th
26. e camera channels enabled on your DVR Go to Menu gt Camera Setup gt Camera Enable to enable your camera s channel CV0104DVR 42 a New You Can See 8 GLOSSARY DDNS Dynamic Domain Name Service Use dyndns org to track your IP on the Internet and assign it an easy to remember domain name instead of an IP number Dynamic IP DHCP A DHCP server assigns an IP address automatically when a device connects to the network A dynamic IP can change when a device is restarted Firmware The built in software that controls the DVR s functions Higher firmware version may be released to provide additional features Please check this product at www svat com to ensure you have the latest firmware version installed Go to Menu gt System Setup to view the firmware version running on your DVR Frame Rate The number of frames that are recorded per second Setting recording to 30 frames second will provide smooth playback but will increase the file size Setting recording to lower frame rates will make playback less smooth but will decrease the file size and you will be able to record more video on your DVR s hard drive IP Internet Protocol A network and transport protocol used for exchanging data over the Internet The address is a string of four numbers separated by periods Such as 111 22 3 444 used to represent a computer or other device on the Internet Monitoring Mode The default mode when the DVR starts up It will display a
27. e router being used Port forwarding of a router is required with your system to allow user access to your network device Regardless of the Linksys Wired Router being used the process of port forwarding is similar You will need to enable the ports by locating the port range forwarding screen With some Linksys routers the port forwarding screen is located within the Applications and Games or Filters tab in others it is located in the advance tools tab The set up instruction outlined below is an example of port forwarding using Linksys Model BEFSR41 Step 1 Open your web browser Enter the router IP address in the address bar as shown below 192 168 1 1 followed by pressing Enter Step 2 Enter the user name and password as shown below admin by default and press the OK button Step 3 Select the Applications and Gaming tab Step 4 Select the Port Range Forwarding tab In the Application column enter a description of your network device e g monitor In the Start entry field enter the first number of the port you need to port forward e g 80 In the End entry field enter the last number of the port you need to port forward e g 80 In the Protocol field select Both In the IP address field enter the computer network IP address you recorded previously during the Quick Set Up Guide process Enable the system by checking the enabled box Select the Save settings button located at the bottom of the page to save your changes Po
28. ecessary jobs while updating firmware Please be patient and the updating process may take a long time cio kere to begin to update firmware kere to ignore and delete the file uploaded just now Writing Progress 100 Click here to reboot DVR browser Firmware Update Completed prompt to restart the device CV0104DVR 40 a New You Can See 7 TROUBLESHOOTING No display on television Make sure all RCA and power cables are plugged in securely and in their proper places Make sure your television is on the correct channel input mode DVR not recording Make sure recording is enabled in each camera s setting Go to Menu gt Camera Setup gt Camera Setting and enable recording for each camera if it has been disabled Make sure recording is enabled and set to the correct recording setting in scheduled recording Go to Menu gt Record Setup gt Record Mode If a line is over any hour of the day that means recording is disabled for that time period Press enter to enable recording for that hour Also make sure you press REC when you return to Monitoring Mode or your scheduled recording will not take effect Your disk may be full By default the DVR should start rewriting over your earliest recorded files but this option may be disabled Go to Menu gt Hard Drive Setup gt Disk Full Set it to OVERWRITE Make sure your DVR is in Monitoring Mode and not at a menu screen or in Playback Mode No playback There is a
29. efine Custom Service button Select Port Forwarding Range of Ports followed by Next CV0104DVR 48 a New You Can See Step 6 In the Port Range screen proceed as follows In the Service Name field type DVR In the Global Port Range field enter in the first box the first number of the port you need to port forward e g 80 and in the second box the ending port number e g 80 In the Base Host Port enter the first port to be forwarded 80 In Protocol select TCP Select the Next button when complete Step 7 In the Nat Configuration Menu use the Service Name down box and select the configuration just created Select the Enable button Port forwarding is now complete 8 MOTOROLA ROUTER The port forwarding process may vary depending on the brand and model number of the router being used Port forwarding of a router is required to allow user access to your network device Regardless of the Motorola router being used the process of port forwarding is similar You will need to enable the ports by locating the port range forwarding screen The set up instruction outlined below is an example of port forwarding a Motorola Router using Motorola Model SBG 1000 Step 1 Open your web browser Enter the router IP address 192 168 0 1 in the address bar as shown below followed by pressing Enter Step 2 Enter admin in the User ID and motorola in the Password dialog box followed by clicking Log In to enter the M
30. enr ts NTSC LOSS m C Auto Detection je ccm 4ch BNC Display 1ch BNC 1ch S Video Live Quad View Single Screen a 720 x 480 Frame Rate Max 120 FPS Play Search a Pene By Time Date Event SPEE lee e keen Normal Fast Forward Mode Quad Each Display OSD and System Yes OSD Language ne English Traditional Chinese Time and Date Stamp Yes Password Protection Menu Password Stop Recording Password ST RA ROE Motion Detection Video Loss Network Network Protocol TCP IP PPPoE DDNS SMPT Static Dynamic Network 10 100 BaseT Ethernet RJ 45 Operating System Written using Linux Propietary Disk Full Warning eee Yes Automatic Overwrite Option Yes LED Indicators ti reote reos Power Record Play Live Housing Aluminum CV0104DVR 51 eee New You Can See Housing Color rte Graphite Grey Power Input rre DC 12V 2A Power
31. er record or live status 3 HDD FULL ALERT Press ENTER to setup ON or OFF whether to trigger the alarm when hard disk is full this setup is only active when the system is under record status 4 BUZZER TIME Press ENTER to setup the buzzer time to continuous CONT and press any button to release this setup CV0104DVR 19 a New You Can See 5 6 EVENT LIST EVENT LIST gt TIME SEARCH EVENT SEARCH PRESS lt gt THEN ENTER PRESS MENU TO EXIT 1 Cursor gt position indicates the current function selected 2 Press and button to move the cursor to the desired item 3 Press ENTER to proceed 4 Press MENU to exit EVENT LIST selection 5 EVENT LIST is situated on the second menu layer Under this menu layer user may setup TIME SERACH or EVENT SEARCH CV0104DVR 20 New You Can See 5 6 1 TIME SEARCH TIME SEARCH 05 01 13 19 27 16 BEGIN TIME 05 01 13 19 27 16 END TIME 05 01 15 15 00 06 PRESS THEN ENTER PRESS MENU TO EXIT 1 TIME SEARCH Displays system recording time begin and end 2 Press and button to select the desired time and date 3 Press ENTER to setup playback starting time and date 4 Press MENU to exit TIME SEARCH selection 5 Press PLAY button to play CV0104DVR 21 a New You Can See 5 6 2 EVENT SEARCH
32. other European countries with separate collection systems This symbol on the product or on its packaging indicates that this product shall not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The recycling of materials will help to conserve natural resources For more detailed information about recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product The power cord is the main power connection Therefore constantly plug and unplug of the power cord might result in malfunction of the product Do not install the product in an environment where the humidity is high Unless the product is waterproof or weatherproof otherwise it can cause the image quality to be poor Do not drop the product or subject them to physical shocks Except for vandal proof or shockproof product Otherwise it will result malfunctions to occur Never keep the product to direct strong light It can damage the product Do not spill liquid of any kind on the product If it gets wet wipe it dry immediately Alcohol or beverage can contain minerals that co
33. otorola configuration page Step 3 Select the Gateway button Step 4 Select the Port Forwarding button Step 5 Select In the Add New Port Forward Entry screen proceed as follows In the Template field select Custom In the Name field select DVR In the Port Start field enter the first number of the port you need to port forward e g 80 In the Port End field enter the ending port number e g 80 In the LAN IP Address field enter the IP address 192 168 0 1 Check the Enable button Finally click the Add button followed by selecting the Apply button Port forwarding is now complete CV0104DVR 49 a New You Can See 9 WIRE ROUTER The port forwarding process may vary depending on the brand and model number of the router being used Port forwarding of a router is required to allow user access to your network device Regardless of the 2 Wire Router being used the process of port forwarding is similar You will need to enable the ports by locating the port range forwarding screen Note in many 2 wire systems it is located in the firewall setting The set up instruction outlined below is an example of port forwarding a 2 Wire Router using 2 Wire Model 1800G Step 1 Open your web browser Enter the router IP address 192 168 1 254 in the address bar as shown below followed by pressing Enter Step 2 Select the Firewall Tab Step 3 Select Firewall Settings Step 4 In the Edit Firewall Settings tab select
34. ould now be in the Configuration Window screen Select the Define Customer Service button followed by selecting the Port Forwarding Ranges of Port option Finally click the Next button Step 7 Use the Select a Service drop down box and select the configuration just created Select the Enable button Port forwarding is now complete 6 NETGEAR ROUTER The port forwarding process may vary depending on the brand and model number of the router being used Port forwarding of a router is required to allow user access to your network device Regardless of the Netgear router being used the process of port forwarding is similar You will need to enable the ports by locating the port range forwarding screen The set up instruction outlined below is an example of port forwarding a Netgear Router using Netgear Model DG 824M Step 1 Open your web browser Enter the router IP address 192 168 0 1 in the address bar as shown below followed by pressing Enter CV0104DVR 47 a New You Can See Step 2 Enter admin in the User Name and password in the Password dialog box to enter the Westell configuration page Step 3 Select the Services button in the Security menu Step 4 In the Services menu select the Add Custom Service button In the Services screen proceed as follows In the Name field select DVR In the Type field select TCP In the Start Port field enter the first number of the port you need to port forward e g 80
35. outer being used the process of port forwarding is similar You will need to enable the ports by locating the port range forwarding screen With some Linksys routers the port forwarding screen is located within the Applications and Games or Filters tab in others it is located in the advance tools tab The set up instruction outlined below is an example of port forwarding using Linksys Model WRK54GV2 Step 1 Open your web browser Enter the router IP address in the address bar as shown below 192 168 1 1 followed by pressing Enter CV0104DVR 45 a New You Can See Step 2 Enter the user name and password as shown below admin by default and press the OK button Step 3 Select the Applications and Gaming tab Step 4 Select the Port Range Forwarding tab In the Application column enter a description of your DVR In the Start entry field enter the first number of the port you need to port forward e g 80 In the End entry field enter the last number of the port you need to port forward e g 80 In the Protocol field select Both In the IP address field enter the computer network IP address you recorded previously during the Quick Set Up Guide process Enable the system by checking the enabled box Select the Save settings button located at the bottom of the page to save your changes Port forwarding is now complete 4 LINKSYS WIRED ROUTER The port forwarding process is dependant on the brand and model number of th
36. pen your web browser Enter the router IP address in the address bar as shown below 192 168 2 1 followed by pressing Enter Step 2 In the status page select the Virtual Servers option located down the left hand side of the page Step 3 In the Administrator s page enter your password The default setting is left blank Select the Submit button In the Virtual Server screen proceed as follows Enable the system by checking the enabled box In the Description column enter a description of your DVR In the Inbound Port entry field enter in the first box the first number of the port you need to port forward e g 80 and the ending port number in the second box in e g 80 In the Type field select Both In the Private IP Address field enter the IP address of the DVR In the Private Ports column re enter in the first box the first number of the port you need to port forward e g 80 and in the second box the ending port number e g 80 Select the Apply Changes button located at the top of the page to save your changes Port forwarding is now complete CV0104DVR 44 a New You Can See 2 D LINK ROUTER The port forwarding process is dependant on the brand and model number of the router being used Port forwarding of a router is required with your system to allow user access to your network device Regardless of the DLINK Wireless Router being used the process of port forwarding is similar You will need to enable the ports by lo
37. quad view of your cameras Playback Mode After you press PLAY and select a recorded file the DVR will enter this mode You cannot enter recording mode or access the menu system directly from this mode Record Mode The DVR enters this mode after you press record or when there is a scheduled time or motion recording You cannot enter playback mode or enter the menu system directly from this mode Static IP An IP assigned to a device that does not change CV0104DVR 43 4 New You Can See 9 PORT FORWARDING YOUR ROUTER FOR USE WITH A NETWORK DVR 1 Belkin Router 2 DLINK Wireless Router 3 LINKSYS Wireless Router 4 LINKSYS Wired Router 5 Westell Router 6 Netgear Router 7 Netopia Router 8 Motorola Router 9 2 Wire Router Note Many routers require restarting for changes to take effect 1 BELKIN ROUTER The port forwarding process is dependant on the brand and model number of the router being used Port forwarding of a router is required with your system to allow user access to your network device Regardless of the Belkin Wired Router being used the process of port forwarding is similar You will need to enable the ports by locating the port range forwarding screen With most Belkin routers the port forwarding screen is located within the Virtual Servers option tab The set up instruction outlined below is an example of port forwarding using Belkin Model F5D8230 4 Step 1 O
38. rm Example When highlighting CH1 TITLE press ENTER to show the display below V CH1 TITLE CAMERA1 V indicates the position of the cursor Press the up and down buttons to move the cursor and press ENTER to change the title maximum 8 characters 5 All channel titles are setup in the same way CV0104DVR 15 a New You Can See 5 3 1 CAMERA SETUP CAMERA SETUP gt CAMERA SELECT RECORD ENABLE MOTION DETECTION MOTION SENSITIVITY HUE CONTRAST BRIGHTNESS PRESS lt gt THEN ENTER PRESS MENU TO EXIT 1 Camera Select Select the camera channel to which you would like to make changes CH 1 4 2 Record Enable Press ENTER to switch the channel recording on off 3 Motion Detection Press ENTER to switch the motion detection function on off 4 Motion Sensitivity Press ENTER to set up the motion sensitivity level 1 5 1 being the most sensitive 5 Press ENTER to adjust the color of the camera 6 Contrast Press ENTER to adjust the camera contrast 7 Brightness Press ENTER to adjust the camera brightness CV0104DVR 16 a New You Can See 5 4 RECORD SETUP RECORD SETUP gt RECORD TYPE VIDEO QUALITY TIME RECORD FRAMERATE MOTION RECORD FRAMERATE SENSOR RECORD FRAMERATE ALARM REC TIME RECORD MODE PRESS lt gt THEN ENTER PRESS MENU TO EXIT 1 Record Type Press ENTER to select
39. rrode the electronic components Do not expose to extreme temperatures CV0104DVR 2 a New You Can See 1 INTRODUCTION The CV0104DVR is a feature packed digital video recorder that can record four different camera views simultaenously and play it back ata smooth 30 frames per second Customize the recording and set a 24 hour recording schedule based on your preferences You can choose to have the DVR record continuously during the day then record only when motion is detected at night During playback you can display each camera in full screen or view all four without losing quality Finding your recorded footage is a breeze Just search for the time and date it was recorded and the file will be displayed Everything is stored on the DVR s internal 80GB hard drive allowing you weeks of recording The DVR can be set to overwrite old footage when the drive does run out of space allowing you continuous recording year after year The CV0204DVR also has a built in internet server for remote viewing Just plug the DVR into your internet connection and set it up with the included software Then simply type in your IP address to monitor your home or business remotely from any internet enabled computer in the world You can even play back recorded footage save picture or movie files to your computer and more all through a web browser This versatile surveillance system is an ideal solution for anyone who wants to monitor their property whe
40. rs International is an organization of community based civilian Crime Stoppers programs which assist police in solving crime You can find more information about Crime Stoppers at www c s i org Local Crime Stoppers programs are partnerships between the public media and local policing organizations Each program is run by a citizen board whose purpose is to advertise a local telephone number which anonymous persons can call with information regarding a crime Callers tipsters may be eligible for a cash reward for their information If your community does not have a Crime Stoppers program and would like information about starting one return this card with the following information NAME PHONE ADDRESS CITY PROV STATE COUNTRY POSTAL ZIP CODE E MAIL ADDRESS Charitable donations can be made to CSI by returning this card in an envelope with your check or money order to the address on the other side Amount THANK YOU www svat com CV0104DVR RON New You Can See NOTES CV0104DVR 55 eee Now You Can See CV0104DVR www svat com a RON Now Yeu Can See SVAT www svat com Disclaimer SVAT does not endorse any of SVAT products for any illegal activities SVAT is not responsible or liable in any way shape or form for any damage vandalism theft or any other action that may occur while a SVAT product is in use by the purchaser Model CV0104DVR www svat com
41. rt forwarding is now complete CV0104DVR 46 a New You Can See 5 WESTELL ROUTER The port forwarding process may vary depending on the brand and model number of the router being used Port forwarding of a router is required to allow user access to your network device Regardless of the Westell Router being used the process of port forwarding is similar You will need to enable the ports by locating the port range forwarding screen The set up instruction outlined below is an example of port forwarding a Westell Router using Westell VERSALINK Step 1 Open your web browser Enter the router IP address 192 168 62 1 in the address bar as shown below followed by pressing Enter Step 2 Enter admin in the User Name and admin in the Password dialog box to enter the Westell configuration page Step 3 Select Configuration Step 4 Select the Define Custom Service Tab Step 5 In the Port Range setting screen proceed as follows In the Service Name field type DVR In the Global Port Range field enter in the first box the first number of the port you need to port forward e g 80 and in the second box the ending port number e g 80 In the Base Host Port enter the first port to be forwarded 80 In Protocol select TCP Select the Next button when complete Step 6 A confirmation window will appear on the screen which shows the same information just entered Select the close button to continue You sh
42. s MENU button to exit System Setup 5 System Setup is situated on the second menu layer Under this menu layer user may setup the system time password return system to default value and language preference etc VERSION displayed represents the FIRMWARE version CV0104DVR 9 New You Can See 5 2 1 TIME SETUP 2005 01 11 17 23 06 A PRESS lt gt THEN ENTER PRESS MENU TO EXIT Time Set Sets the time and date on your DVR Use the up and down arrows to select a value to change and press ENTER to change the value When you are finished press MENU to return to the previous menu screen Time is in YEAR MONTH DAY format CV0104DVR 10 a New You Can See 5 2 2 PASSWORD SETUP PASSWORD SETUP gt PASSWORD CHANGE MENU PASSWORD STOP REC PASSWORD PRESS lt gt THEN ENTER PRESS MENU TO EXIT 1 Cursor gt position indicates the current function selected 2 Press the up and down buttons to move the cursor 3 Press ENTER button to proceed 4 Press MENU button to exit Password Setup 5 Select MENU PASSWORD to password protect your DVR menu from unwanted changes The password must be entered any time someone tries to access the main menu Select MENU PASSWORD again to turn this feature off 6 Select STOP REC PASSWORD to password protect your DVR while it is recording The password must be entered to
43. scheduled recording time motion time amp motion off throughout a 24 hour day For example you may want to record continuously from 9 00 AM to 5 00 PM but only record when motion is detected the rest of the time IMPORTANT after you make changes and return to monitoring mode you must press RECORD When you press STOP the DVR will not adhere to your Record Mode settings until you press RECORD again Use the up and down and ENTER buttons to change the type of recording for the specified hour of the day 2 T Time indicates continuous record 3 M TIME MOTION 1 When motion has been detected it will be recorded by Motion Record Frame Rate 2 Otherwise it is recorded by Time Record Rate 4 OFF The DVR will not record during the specified time CV0104DVR 18 7 2 New You Can See 5 5 BUZZER SETUP BUZZER SETUP gt ALARM ALERT VIDEO LOSS ALERT HDD FULL ALERT BUZZER TIME RELAY OUT TIME SENSOR TYPE PRESS lt gt THEN ENTER PRESS MENU TO EXIT 1 ALARM ALERT Press ENTER to setup ON or OFF whether to trigger the alarm when motion event has been detected this setup is only active when the system is under record status and schedule record is setup to M Mix 2 VIDEO LOSS ALERT Press ENTER to setup ON or OFF whether to trigger the alarm when video loss has been detected this setup is only active when the system is und
44. ssword Cx Ce CV0104DVR 27 ____ Now You Can See 6 2 4 1 ONLINE CONNECTION Before entering remote connection install ActiveX If you are running Windows XP you most likely have it and check your browser setup by following the procedures below A Open Internet Explorer under Tools and select Internet Options Mail and News Synchronize Windows Update Show Related Links Internet IFI5 Tools gt Internet Options B Select Security then Custom Level Internet Options General Security Privacy Content Connections Programs Advanced Select a Web content zone to specify its security settings e amp 0 Localintranet Trusted sites Restricted This zone contains all Websites you haven t placed in other zones Security level far this zone Custom Custom settings To change the settings click Custom Level To use the recommended settings click Default Level Default Level Security gt Custom Level CV0104DVR 28 ee ce Aa a Now You Can See Security Settings ActiveX controls and plug ins Download signed ActiveX controls Disable Enable Prompt Download unsigned ActiveX controls Disable Enable On I Initialize pori script ActiveX controls not marked as safe Disable Enable Prompt Meie Ambi membela mm Ad i Reset custom settings Reset to Medium
45. stop recording Select STOP REC again to turn this feature off 7 When an incorrect password has been entered PASSWORD INCORRECT will be shown on the display To disable the message press button QUAD CH1 CH2 CH3 or CV0104DVR 11 New You Can See 5 2 2 1 CHANGE PASSWORD CURRENT PASSWORD NEW PASSWORD CONFIRM PASSWORD PRESS MENU TO EXIT 1 Press ENTER to show the display above 2 Enter the current password CURRENT PASSWORD 3 Enter new password NEW PASSWORD 4 Confirm the new password CONFIRM PASSWORD 5 When password change is successful the system will display PASSWORD CHANGED Default Value 111111 If password entered is incorrect you will receive a message NO PASSWORD CHANGED to inform you message flashes three times and the system returns to Password setup selection CV0104DVR 12 a New You Can See 5 2 3 LOAD DEFAULT PRESS ENTER TO RESET PRESS MENU TO EXIT Press enter on this option to return the DVR to its factory default settings Press enter again to confirm or menu to cancel When the message DVR RESET COMPLETED TURN OFF AND ON THE VCR is displayed restart the DVR CV0104DVR 13 New You Can See 5 2 4 LANGUAGE SETUP SYSTEM SETUP TIME SET PASSWORD SET LOARD DEFAULT LANGUAGE SET ENGLISH VERSION V1 2 PRESS lt gt THEN ENTER
46. t support audio so if you are using an audio video RCA wire there is no need to plug in the red or white inputs On your television switch to the video audio input channel Your system is now installed and ready for use CV0104DVR 4 a New You Can See 3 NAME AND FUNCTION OF EACH PART 3 1 FRONT PANEL o PWR CREE 42 22229 e e 6 e e a 0000 MENU ENTER REV STOP PAUSE FF PLAY REC Digital Video Recorder Quad screen display CH 1 screen display H CH 2 screen display a CH screen display Hj CH 4 screen display MENU Menu button Up direction button Down direction button ENTER Enter button 0 REW Rewind button 1 STOP Press this button during playback and recording to return to monitoring mode 12 PAUSE Press this button during playback mode to pause 13 FF Fast forward button 14 PLAY Play button 15 REC Record button 16 PWR Power indicator 3 2 REAR PANEL 2 CAUTION T 7 DONOTOPEN FREORELETRC SHOCK SVICEO VIDEDOUT 6 o 5 2 Video Input VIDEO IN Connect to cameras DC 12V 4 2A Power Input terminal power socket S Video Output S VIDEO OUT Connect to the monitor Video Output VIDEO OUT Connect to the monitor Cooling Fan RJ45 Internet connection terminal
47. te To view complete interface PC resolution must be adjusted to 1024 768 6 3 1 LIVE DISPLAY View Make changes on image display Rotate Make changes on image direction Image Recording Record function setup Save Current Picture Save the current image Welcome Administrator Display current user name About Version description Move the cursor inside the image range right mouse click to display 9 function selections View Rotate Image Recording Fl1 Current Picture As F12 Welcome administrator About CV0104DVR 31 a New You Can See 6 3 2 VIEW Two types of display method 1 Resizable Adjustable image size 2 Actual size The actual image size 6 3 3 ROTATE Four types of rotate settings 1 Rotate 0 Default state 2 Rotate 180 Rotate the image by 180 degrees 3 Flip horizontal Image flips horizontally 4 Flip vertical Image flips vertically 6 3 4 IMAGE RECORDING Image Recording Setup Display Save as JPEG Save as picture file Save as AVI Save as AVI animation file Save as JPEG No Limit Unrestricted image storage continuous Number Image storage according to number Save interval Image storage according to 1 10 second e g Enter 10 then 1 frame is stored per second Enter 50 then 1 frame is stored in 5 seconds Size Image storage according to size Time Image storage according to time Save Path
48. ther they re at home or away FEATURES Easy setup and installation e Live monitoring through the internet from anywhere in the world e Includes 80GB hard drive Password protected recording and menus e Supports up to 4 color or B amp W cameras Has built in motion detection Find your recorded footage fast and easy Has built in time and date stamp e M JPEG compression technology Easily connects to any TV or Monitor CV0104DVR 3 A RON New You Can See INSTALLATION CONNECTORS ON THE REAR PANEL Please setup the connection by following the illustration shown below detailed instructions on using the network function can be found in Section 9 CAUTION a v DONOTOPEN D FREOR BETRE SKOCI VISA 4 m 240 110 AC VIDEO MONITOR Plug the power cord into your DVR and plug it into an outlet SVAT recommends plugging it into a surge protected power bar for your device s protection Plug the BNC Connectors into each video input you plan on using For example if you are using 3 cameras with this system then plug BNC convertors into inputs 1 3 Plug BNC convertor into the video output as well Plug your camera s into the video input jacks using the 60ft extension wires Use an RCA wire to connect your television to the video output of the DVR Make sure the RCA wire is plugged into the video input of your television Note This system does no

Instruction Manual - Pdfstream.manualsonline.com

Contents

Download Pdf Manuals

Related Search

Related Contents