INSTALLATION INSTRUCTIONS
Contents
1. If the burner does not light properlv turn the control knob to the OFF position Check that the burner head is in the proper position Check that the power supply cord is plugged in and that the circuit breaker or house fuse has not blown Make sure that the shut off valve is in the ON position Check operation again if the burner does not light properlv at this point contact a Wolf authorized service center IMPORTANT NOTE Initial lighting of the cooktop burner may take slightly longer as air in the system must be purged before gas can be supplied to the burner Shut Off Valve 1 2 Adapter Flexible Metal Connector 1 2 Nipple use pipe joint compound on ends 1 2 Adapter Ha Boom om an Pressure Regulator 1 2 Nipple use pipe joint compound on ends Gas supply line connection Dimensions in parentheses are in millimeters unless otherwise specified CONTACT INFORMATION Wolf Customer Service 800 332 9513 Website wolfappliance com 14 WOLF MULTI FUNCTION COOKTOP COOKTOP REMOVAL If it is necessarv to remove the multi function cooktop for cleaning or service shut off the gas supply Disconnect the gas and electric supplv Remove the mounting brackets on the right and left side of the burner box and remove the cooktop Reinstall in the reverse order and check the gas connection for leaks TROUBLESHOOTING IMPORTANT NOTE If the multi function cooktop does2. Installations and repairs must be performed by a qualified or licensed contractor plumber or gas fitter qualified or licensed by the state province or region where this appliance is being installed Use only gas shut off valves approved for use within the state province or region where this appliance is being installed A flexible gas connector when used must not exceed 3 9 m INSTALLATION INSTRUCTIONS SITE PREPARATION IMPORTANT NOTE Installation of the Wolf OVERHEAD CABINET DIMENSIONS gas multi function cooktop must meet the following location requirements All dimen sions listed are minimum requirements for safe operation Refer to the illustration below C Minimum spacing between overhead side cabinets must be greater than or equal to the nominal width of the module s D Minimum 18 457 vertical distance from A WARNING the countertop to the bottom of side cabinets within minimum side clearance To eliminate the risk of burns or fire by reaching over heated surface units E Minimum vertical distance between the cabinet storage space located above the countertop and combustible materials surface units should be avoided If above the cooktop module must be cabinet storage is to be provided the risk 30 762 can be reduced by installing a ventilation hood that projects horizontally a F Minimum 21 2 64 from rear wall minimum of 5 127 beyond the bottom G Maximum 13 330 depth of over
3. also required Contact your Wolf dealer for information on these accessory components IMPORTANT NOTE Refer to specific installation requirements and limitations for each integrated module Review specific installation instructions for product to product capabilities Additional information is provided on our website wolfappliance com 593 4 1518 FOUR MODULES WIDTH OR lt 441 2 1130 THREE MODULES WIDTH OR 441 4 1124 30 COOKTOP AND ONE MODULE je 291 4 743 gt TWO MODULES WIDTH 591 2 1511 30 COOKTOP AND TWO MODULES OR gt 501 4 1276 36 COOKTOP AND ONE MODULE 14 191 a lt 356 489 21 2 min CUT OUT CUT OUT 64 WIDTH DEPTH e2 f FRONT OF COUNTERTOP Countertop cut out dimensions for installation of multiple cooktops and or modules ACCESSORIES Optional acces sories are available through vour Wolf dealer To obtain local dealer information visit the showroom locator section of our website wolfappliance com WOLF MULTI FUNCTION COOKTOP GAS SUPPLV REQUIREMENTS A WARNING EXPLOSION HAZARD Use a new CSA approved gas supply line and install a gas shut off valve Securelv tighten all gas connections For LP gas have a qualified technician make sure the gas pressure does not exceed 14 34 9 mb WC water column Failure to do so can result in explosion fire or death IMPORTANT NOTE The gas
4. or Wolf Appliance Inc at 800 332 9513 You can also visit our website at wolfappliance com IMPORTANT NOTE This appliance must be installed in accordance with National Electrical Codes as well as all state municipal and local codes The correct voltage frequency and amperage must be supplied to the appliance from a dedicated grounded circuit which is protected by a properly sized circuit breaker or time delay fuse The proper voltage frequency and amperage ratings are listed on the product rating plate Record the model and serial numbers before installing the cooktop Both numbers are listed on the rating plate located on the underside of the cooktop Refer to the illustration below Location of rating plate under cooktop Rating plate location A WARNING If the information in this book is not followed exactly a fire or explosion may result causing property damage personal injury or death IMPORTANT NOTE Installation and service must be performed by a qualified installer service agency or the gas supplier Warranty service must be performed by a Wolf authorized service center Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance A ventilation hood or downdraft system is recommended for use with the Wolf gas multi function cooktop WHAT TO DO IF YOU SMELL GAS Do not try to light any appliance Do not touch an
5. MULTI FUNCTION COOKTOP INSTALLATION INSTRUCTIONS LUOLF IIOLF CONTACT INFORMATION Wolf Customer Service 800 332 9513 Website wolfappliance com WOLF is a registered trademark of Wolf Appliance Inc As you follow these instructions you will notice WARNING and CAUTION symbols This blocked information is important for the safe and efficient installation of Wolf equip ment There are two types of potential hazards that may occur during installation A CAUTION signals a situation where minor injury or product damage may occur if you do not follow instructions A WARNING states a hazard that may cause serious injury or death if precautions are not followed Another footnote we would like to identify is IMPORTANT NOTE This highlights informa tion that is especially relevant to a problem free installation WOLF MULTI FUNCTION COOKTOP INSTALLATION REQUIREMENTS IMPORTANT NOTE This installation must be completed bv a qualified installer or Wolf authorized service center technician a Installer Please read the entire Installation Instructions prior to installation Save these instructions for the local inspector s refer ence then leave them with the homeowner Homeowner Please read and keep these instructions for future reference and be sure to read the entire use amp care information prior to use Any questions or problems about the installa tion should be directed to your Wolf dealer
6. erall Height 5 127 Overall Depth 21 533 Minimum Cabinet Depth 223 4 578 Minimum Height Clearance 5 127 Cut Out Width 14 356 Cut Out Depth 191 4 489 A minimum height clearance of 51 2 140 is required between countertop and any combustible surface directly below the cooktop Unit dimensions may vary to 1 s 3 33 838 RECOMMENDED lt CABINET WIDTH gt 30 762 15 381 13 max OVERALL WIDTH E ie 457 21 2 191 4 489 aie 64 COOKTOP CUT OUT 21 2 min l gt lt DEPTH gt lt 64 5 127 N l 36 914 Overall Dimensions STANDARD FLOOR TO COUNTERTOP HEIGHT LOCATION OF GAS SUPPLY MAY ALSO EXTEND 5 ON FLOOR FROM BACK WALL 5 H 127 7 min 178 COUNTERTOP TC CUT OUT TO 14 356 COMBUSTIBLE COMBUSTIBLE COOKTOP CUT OUT MATERIALS I4 MATERIALS 4 WIDTH ABOVE COOKTOF BOTH SIDES I I 5 127 E 6 45 381 La 15 _ 381 LOCATION OF GAS SUPPLY MAY ALSO EXTEND 5 ON FLOOR FROM BACK WALL 15 381 NV NOTE Application shown allows for installation of two 15 381 modules side by side with 33 838 recommended cabinet width 18 457 recommended cabinet width for installation of single 15 381 cooktop or module Minimum clearance from both side edges
7. es sional for more concise blower requirements IMPORTANT NOTE When installing a ventila tion hood refer to the specific requirements of the hood for the minimum dimension to countertop ACCESSORIES Optional acces sories are available through your Wolf dealer To obtain local dealer information visit the showroom locator section of our website wolfappliance com 11 12 WOLF MULTI FUNCTION COOKTOP COOKTOP INSTALLATION Insert the cooktop into the countertop cut out opening Center the cooktop in the opening and make sure that the front edge of cooktop is parallel to the front edge of the countertop Check that all required clearances are met Use a pencil to outline the rear edge of the cooktop on the countertop Remove the cooktop from the countertop opening IMPORTANT NOTE When repositioning the cooktop in the countertop cut out opening lift the entire cooktop up from the opening to prevent scratching the countertop Remove the foam strip from the hardware package Apply the foam strip around the bottom of the burner box flush with the edge as shown in the illustration below Reinsert the cooktop into the countertop opening Check that the cooktop is parallel to the front edge of the countertop Lift the entire cooktop to make adjustments and align the rear edge with the pencil line Attach the brackets to the burner box by insert ing the clips into the rectangular punchouts on the left and right
8. head and cabinet side cabinets directly above and within side clearance LOCATION IN COUNTERTOP A WARNING A Minimum flat countertop surface Must be Failure to locate the cooktop module equal to or greater than the width of the without the proper clearances will result module s in a fire hazard B Minimum 7 178 wide clearance from the module side edge to any combustible surface up to 18 457 above the counter top noted by shaded area Minimum installation clearances Dimensions in parentheses are in millimeters unless otherwise specified Model IM15 S WOLF MULTI FUNCTION COOKTOP INSTALLATION SPECIFICATIONS The illustrations below provide the overall dimensions installation specifications and countertop cut out for model IM15 S If the cooktop is not installed above an oven the gas service may be supplied through the floor When an oven is installed below the cooktop unless you are using cabinets deeper than 24 610 it is recommended that the electrical supply be placed in the base cabinet to the right of the oven Refer to the installation specifications illustration below for specifics on placement of the electrical and gas supply IMPORTANT NOTE When multiple cooktops and or modules are installed side by side refer to the countertop cut out dimensions on page 7 21 533 OVERALL DEPTH MODEL IM1 5 S DIMENSIONS Overall Width 15 381 Ov
9. ied electrician if you are not sure whether the cooktop is properly grounded IMPORTANT NOTE Do not ground to a gas pipe A 120 VAC 60 Hz 15 amp fused electrical supply is required A time delay fuse or circuit breaker is recommended It is recommended that a separate circuit serving only this appli ance be provided IMPORTANT NOTE A ground fault circuit interrupter GFCI is not recommended and may cause interruption of operation Electronic ignition systems operate within wide voltage limits but proper ground and polarity are necessary In addition to checking that the electrical outlet provides 120 VAC power and is correctly grounded the outlet must be checked by a qualified electrician to see if it is wired with correct polarity A wiring diagram covering the control circuit for the Wolf multi function cooktop model can be found on page 15 RECOMMENDED GROUND METHOD IMPORTANT NOTE For your personal safety this cooktop must be grounded It is equipped with a 6 1 8 m power cord with 3 prong grounding plug To minimize possible shock hazard the power cord must be plugged into a 3 prong ground type electrical outlet grounded in conformance with the National Electrical Code ANSI NFPA 70 latest edition or Canadian Electrical Code CSA and all local codes and ordinances If an electrical outlet is not available it is the obligation of the customer to have a properly grounded 3 prong electrical outlet insta
10. l shut off valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pres sures greater than 5 psi 3 5 kPa Testing below 5 psi 3 5 kPa 14 34 9 mb WC gauge or lower The cooktop must be isolated from the gas supply piping system by closing its individual manual shut off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 5 psi 3 5 kPa IMPORTANT NOTE This installation must conform with local codes and ordinances In the absence of local codes installations must conform with the American National Standard National Fuel Gas Code and National Electrical Code regulations STANDARDS Copies of the standards listed may be obtained from National Fire Protection Association Battervmarch Park Quincv Massachusetts 02269 Canadian Standard Association 178 Rexdale Blvd Etobicoke Toronto Ontario M9W 1R3 10 WOLF MULTI FUNCTION COOKTOP ELECTRICAL REQUIREMENTS A WARNING ELECTRICAL SHOCK HAZARD Plug into a grounded 3 prong electrical outlet Do not remove ground prong Do not use an adapter Failure to follow these instructions can result in electric shock fire or death IMPORTANT NOTE If codes permit and a separate ground wire is used it is recom mended that a qualified electrician determine that the ground path is adequate IMPORTANT NOTE Check with a qualif
11. lled by a qualified electrician Grounding Plug Grounding Type Electrical Outlet Electrical ground INSTALLATION INSTRUCTIONS VENTILATION OPTIONS IMPORTANT NOTE It is recommended that vou operate the Wolf multi function cooktop with either a Wolf cooktop ventilation hood Blower requirements mav varv due to the length of ducting and number of angles The basic recommendation is 1 CFM per 100 btu hr downdraft svstem or pro ventilation hood Contact vour Wolf dealer for details Cooktop wall hood 30 762 or 36 914 widths in classic stainless steel Cooktop island hood 42 1067 width in classic stainless steel Downdraft ventilation svstem 30 762 or 36 914 widths with top cover and control panel in classic platinum and carbon stainless steel finishes adequate countertop depth is required Pro wall hood 22 559 24 610 or 27 686 depths and 30 762 to 66 1676 widths in classic stainless steel Pro wall chimnev hood 36 914 to 54 1372 widths in classic stainless steel Pro island hood 36 914 to 66 1676 widths in classic stainless steel Pro hood liner available in widths to accommodate 36 914 to 60 1524 hood shells All hoods have welded seams sealed halogen lighting and removable dishwasher safe filters Dimensions in parentheses are in millimeters unless otherwise specified 03 kW Always consult your HVAC prof
12. m X Strip Pressure Rear of Regulator ro Cooktop Bracket NV l q 31 2 89 Access do Gas Flow Clip Clamping Cap Ii Arrow Screw m Points Up Foam strip application Bracket installation Gas pressure regulator INSTALLATION INSTRUCTIONS GAS LEAK TESTING Use a brush and liquid detergent to test all gas connections for leaks Bubbles around connec tions will indicate a leak If a leak appears shut off gas valve controls and adjust connections Then check connections again Clean all the detergent solution from the cooktop A WARNING Never test for a gas leak with a match or other flame COMPLETING THE INSTALLATION Once the cooktop has been checked for anv gas leaks plug the power supply cord into the grounded electrical outlet Place the burner head on the burner base and position the burner grate over the burner assembiv IMPORTANT NOTE Do not seal the cooktop to the countertop It must be removed if service is necessarv SURFACE BURNERS INITIAL LIGHTING The cooktop burner uses an electronic igniter in place of a standing pilot When the cooktop control knob is pushed in and turned to the HIGH position the svstem creates a spark to light the burner This sparking continues until the electronic ignition senses a flame To check operation of the cooktop burner push in and turn the control knob to the HIGH position The flame should light within four seconds
13. multi function cooktop must be connected to a regulated gas supplv IMPORTANT NOTE This installation must conform with local codes and ordinances In the absence of local codes installations must conform with American National Standard National Fuel Gas Code ANSI Z223 1 latest edition or CANI B149 1 or 2 IMPORTANT NOTE The natural gas multi function cooktop model IM15 S is rated for elevations up to 8 000 2438 m without adjustment Install a high altitude kit for eleva tions from 8 000 2438 m to 10 000 3084 m The LP gas multi function cooktop model IM15 S LP is rated for up to 10 000 3084 m The gas multi function cooktop is equipped for use with natural or LP gas It is design certified by the Canadian Standards Association CSA for natural or LP gases The product rating plate located on the underside of the cooktop has information on the type of gas that should be used If this information does not agree with the type of gas available contact your Wolf dealer To obtain local dealer information visit the showroom locator section of our website wolfappliance com The gas multi function cooktop is supplied with a 1 2 NPT male gas connection at the right rear corner of the cooktop Provide a gas supply line of 3 4 rigid pipe to the cooktop location A smaller size pipe on long runs may result in insufficient gas supply Pipe joint compounds suitable for use with LP gas should be used For LP gas
14. not operate properly follow these troubleshooting steps Verifv that power is being supplied to the cooktop Check that gas valves are turned to the ON position Check the gas supply and electrical connections to ensure that the installation has been completed correctiv Refer to the troubleshooting guide in the Wolf multi function cooktop use amp care information If the cooktop still does not work contact a Wolf authorized service center Do not attempt to repair the cooktop yourself Wolf is not responsible for service required to correct a faultv installation IF YOU NEED SERVICE Maintain the quality built into your multi function cooktop by calling a Wolf authorized service center For the name and number of the Wolf authorized service center nearest you check the contact amp support section of our website wolfappliance com or call Wolf customer service at 800 332 9513 When calling for service you will need the model and serial number of your multi function cooktop Both numbers are listed on the rating plate located on the under side of the cooktop Refer to the illustration on page 3 INSTALLATION INSTRUCTIONS WIRING DIAGRAM WHITE 3 CONDUCTOR MODULE POWER CORD Model IM15 S The information and images in this book are the copyright property of Wolf Appliance Inc an affiliate of Sub Zero Inc Neither this book nor any information or images contained herein may be copied or
15. of cooktop cut ou to combustible materials up to 18 457 above countertop Minimum clearance from rear edge of cooktop cut out to combustible materials up to 18 457 above countertop Installation Specifications and Countertop Cut Out Dimensions Dimensions in parentheses are in millimeters unless otherwise specified 14 356 COOKTOP CUT OUT I WIDTH 191 a 489 COOKTOP 21 2 min CUT OUT DEPTH 64 f FRONT OF COUNTERTOP INSTALLATION INSTRUCTIONS INSTALLATION OPTIONS MULTIPLE COOKTOP INSTALLATION If the multi function cooktop is to be used with anv combination of additional cooktop units or modules with a filler strip the cut out width is calculated bv adding the corresponding units cut out dimensions plus 11 4 32 for each additional unit Refer to the illustration below IMPORTANT NOTE When multiple cooktops and or modules are installed side by side each unit must have its own separate recommended electrical circuit When multiple gas cooktops and or modules are installed next to one another they can receive their gas supply from a common line However each unit MUST have its own gas pressure regulator installed between the mainline and the cooktop or module When two or more modules are installed together an integrated module filler strip 802726 is recommended If a downdraft venti lation system is also installed an integrated module support for downdraft ventilation 803386 is
16. piping or tubing size can be 1 2 minimum If local codes permit a new CSA design certified 4 5 1 2 1 5 m long 1 2 or 3 4 ID flexible metal appliance connector is recom mended for connecting this cooktop to the gas supply line Do not kink or damage the flexible connector when moving the cooktop The gas pressure regulator has 1 2 female pipe threads You will need to determine the fittings required depending on the size of your gas supply line flexible metal connector and shut off valve If rigid pipe is used as a gas supply line a combination of pipe fittings must be used to obtain an in line connection to the cooktop All strains must be removed from the supply and gas lines so the cooktop will be level and in line INSTALLATION INSTRUCTIONS GAS SUPPLY REQUIREMENTS IMPORTANT NOTE The supply line must be equipped with an approved external gas shut off valve located near the cooktop in an accessible location Do not block access to the shut off valve The inlet pressure to the regulator should be as follows for operation and checking the regu lator setting Natural Gas Set pressure 5 12 5 mb WC supply pressure 7 14 17 5 34 9 mb max LP Gas Set pressure 10 25 mb WC supply pressure 12 14 29 9 34 9 mb WC Dimensions in parentheses are in millimeters unless otherwise specified LINE PRESSURE TESTING Testing above 5 psi 3 5 kPa 14 34 9 mb WC gauge The cooktop and its individua
17. side of the burner box Insert the 31 2 89 clamping screws into the brackets Use a screwdriver to tighten the clamping screws against the underside of the countertop Refer to the illustration below Do not overtighten screws GAS PRESSURE REGULATOR Install the gas pressure regulator with the arrow on the regulator pointing up toward the unit and in a position where you can reach the access cap Refer to the illustration below A natural gas and LP compatible pipe joint compound should be used to ensure a gas tight seal IMPORTANT NOTE All connections must be wrench tightened Do not make connections to the gas pressure regulator too tight this may crack the regulator and cause a gas leak Do not allow the regulator to turn on the pipe when tightening fittings GAS SUPPLY LINE CONNECTION Assemble the flexible metal connector from the gas supply pipe to the gas pressure regula tor You will need to determine the fittings required depending on the size of your gas supply line flexible metal connector and shut off valve Refer to the illustration on page 13 Use a pipe joint compound made for use with natural and LP gas If a flexible metal connec tor is used be sure the tubing is not kinked Open the shut off valve in the gas supply line Wait a few minutes for the gas to move through the line Refer to the illustration on page 9 Cooktop Burner Box Sm Countertop Burner Box Foa
18. used in whole or in part without the express written permission of Wolf Appliance Inc an affiliate of Sub Zero Inc OWolf Appliance Inc all rights reserved WOLF APPLIANCE INC P O BOX 44848 MADISON WI 53744 800 332 9513 WOLFAPPLIANCE COM LUOLF
19. y electrical switch Do not use any phone in your building Immediately call your gas supplier from a neighbor s phone Follow the gas supplier s instructions u If you cannot reach your gas supplier call the fire department RATING PLATE INFORMATION Model Number IM15 S Serial Number WOLF MULTI FUNCTION COOKTOP BEFORE VOU START Proper installation is your responsibility Have a qualified technician install this cooktop You must also ensure that electri cal installation is adequate and in compli ance with all local codes and ordinances a The Wolf multi function cooktop is manu factured for use with natural gas or LP gas Please check the product rating plate for type of gas needed Proper gas supply connection must be available refer to gas supply requirements on page 8 Electrical ground is required see electrical requirements on page 10 Check the location where the cooktop will be installed The location should be away from strong draft areas such as windows doors and strong heating vents or fans Do not obstruct flow of combustion and ventilation air Make sure you have everything necessary for correct installation It is the responsibil ity of the installer to comply with the instal lation clearances specified on the product rating plate The rating plate can be found on the underside of the cooktop This cooktop is intended for indoor use COMMONWEALTH OF MASSACHUSETTS
Download Pdf Manuals
Related Search