SC846 X9 Universal Air Shroud Users Guide_1.0.book
Contents
1. Figure 3 7 Default Configuration 3 8 Chapter 3 Configuration and Installation 3 5 Installing the SC846 X9 Universal Air Shroud To install the SC846 X9 universal air shroud follow the procedure below This procedure is the same for all configurations of the SC846 X9 universal air shroud in Supermicro systems Installing the SC846 X9 Universal Air Shroud in SC846 Chassis Systems j Configure the air shroud to fit in your system See Section 3 4 for details on configuring the air shroud Secure the rear edge of the SC846 air shroud component part A to the top rear part of the chassis interior Align the air shroud so that the slot of air shroud s front mounts with the top front part of the chassis interior see Figure 3 8 Figure 3 8 Inserting Air Shroud onto a System Mainboard 3 9 SC846 Air Shroud User s Guide 3 Make sure the SC846 X9 universal air shroud is mounted directly on the mainboard of its system so that the air shroud covers the system mainboard over the CPU s and memory slots see Figure 3 9 Figure 3 9 Air Shroud Mounted into System Chassis NOTE The air shroud should be mounted flush with the power supply housing the front fans in the chassis and the rear fans of the chassis if it has been f installed properly Some cables are supposed to go under the air shroud Detach breakaway tabs if required for cable access 4 Secure the top cover back on your system2. 3 10 Disclaimer The products sold by Supermicro are not intended for and will not be used in life support systems medical equipment nuclear facilities or systems aircraft aircraft devices aircraft emergency communication devices or other critical systems whose failure to perform be reasonably expected to result in significant injury or loss of life or catastrophic property damage Accordingly Supermicro disclaims any and all liability and should buyer use or sell such products for use in such ultra hazardous applications it does so entirely at its own risk Furthermore buyer agrees to fully indemnify defend and hold Supermicro harmless for and against any and all claims demands actions litigation and proceedings of any kind arising out of or related to such ultra hazardous use or sale SC846 Air Shroud User s Guide Notes
3. Er 10 jel EI i I Tan The SC846 X9 universal air shroud s Component Part B Figure 3 2 can be moved in and out to resize the X9 universal air shroud s size to fit the mainboard using three sliding positions labeled 0 1 and 2 The bottom of Component Part B can be detached to allow for cable access under the air shroud 3 2 Chapter 3 Configuration and Installation Component Part C Figure 3 3 Component Part C Component Part C Alignment Slots The SC846 X9 universal air shroud s partition Component Part C Figure 3 3 can be mounted on the underside of Component Part A by inserting its locking tabs into the four aligned slots provided on part A Component Part C can only fit onto 12 X 13 motherboards so it can be removed out if it is not required SC846 Air Shroud User s Guide Component Part D Figure 3 4 Component Part D Component Part D Alignment Slots The SC846 X9 universal air shroud s Component Part D 55mm wide tear drop module can be mounted on the underside of Component Part A by inserting its locking tabs into the al
4. shroud includes the following features e Main air shroud component Four detachable components for creating multiple configurations e Breakable tabs for power cable management e Clear plastic material construction for ease of viewing 1 4 Returning Merchandise for Service A receipt or copy of your invoice marked with the date of purchase is required before any warranty service will be rendered You can obtain service by calling your vendor for a Returned Merchandise Authorization RMA number When returning to the manufacturer the RMA number should be prominently displayed on the outside of the shipping carton and mailed prepaid or hand carried Shipping and handling charges will be applied for all orders that must be mailed when service is complete For faster service RMA authorizations may be requested online at http www supermicro com support rma Whenever possible repack the chassis in the original Supermicro carton using the original packaging material If these are no longer available be sure to pack the chassis securely using packaging material to surround the chassis so that it does not shift within the carton and become damaged during shipping This warranty only covers normal consumer use and does not cover damages incurred in shipping or from failure due to the alteration misuse abuse or improper maintenance of products During the warranty period contact your distributor first for any product problems 1
5. 2 Chapter 1 Introduction 1 5 Contacting Supermicro Headquarters Address Tel Fax Email Web Site Europe Address Tel Fax Email Asia Pacific Address Tel Fax Web Site Technical Support Email Tel Super Micro Computer Inc 980 Rock Ave San Jose CA 95131 U S A 1 408 503 8000 1 408 503 8008 marketing supermicro com General Information support supermicro com Technical Support www supermicro com Super Micro Computer B V Het Sterrenbeeld 28 5215 ML s Hertogenbosch The Netherlands 31 0 73 6400390 31 0 73 6416525 sales supermicro nl General Information support supermicro nl Technical Support rma supermicro nl Customer Support Super Micro Computer Inc 4F No 232 1 Liancheng Rd Chung Ho 235 Taipei County Taiwan R O C 886 2 8226 3990 886 2 8226 3991 www supermicro com tw support supermicro com tw 886 2 8226 5990 SC846 Air Shroud User s Guide Notes Chapter 2 System Safety Please read and follow all safety precautions below before using your Supermicro product 2 1 Electrical Safety Precautions Basic electrical safety precautions should be followed to protect yourself from harm and the server from damage Be aware of how to power on off the enclosure power supplies and the individual blades as well as the room s emergency power off switch disconnection switch or electrical outlet If
6. Chapter 3 Configuration and Installation 3 4 Configuring the SC846 X9 Universal Air Shroud The SC846 X9 universal air shroud can be customized into multiple configurations for Supermicro systems With all parts attached with three positions each for Component Parts B and E and Component Part C and D many possible combinations can be configured for the SC846 X9 universal air shroud With component parts detached more configurations are possible Some recommended example configurations for specific Supermicro motherboards are shown below in Table 3 2 Component Parts not listed in the table have been removed All are 13 68 x 13 or 12 x 13 Intel Xeon or AMD Opteron motherboards Table 3 2 Examples of SC846 X9 Universal Air Shroud Configurations Motherboard Slot and Tab Positions H8DG6 Tab Position 1 Part B Tab Position B Part E Part D and Partition Part C attached Tab Position 0 Part B Tab Position A Part E Part D and Partition Part C X8DT6 F attached X8DTN F Tab Position 0 Part B Tab Position A Part E Part D attached X9DA6 Tab Position 2 Part B Tab Position C Part E Partition Part C attached X9DR6 F Tab Position 2 Part B Tab Position B Part E Partition Part C attached X9DR6 LN4F Tab Position 2 Part B Tab Position C Part E already connected Figure 3 7 V4 NOTE The default configuration is with Component Parts A B C D and E 3 7 SC846 Air Shroud User s Guide
7. SUPERMICR SC846 X9 Universal Air Shroud User s Guide Revison 1 0 SC846 Air Shroud User s Guide The information in this User s Guide has been carefully reviewed and is believed to be accurate The vendor assumes no responsibility for any inaccuracies that may be contained in this document makes no commitment to update or to keep current the information in this manual or to notify any person or organization of the updates Please Note For the most up to date version of this manual please see our web site at www supermicro com Super Micro Computer Inc Supermicro reserves the right to make changes to the product described in this manual at any time and without notice This product including software if any and documentation may not in whole or in part be copied photocopied reproduced translated or reduced to any medium or machine without prior written consent IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT INDIRECT SPECIAL INCIDENTAL SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES IN PARTICULAR SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY HARDWARE SOFTWARE OR DATA STORED OR USED WITH THE PRODUCT INCLUDING THE COSTS OF REPAIRING REPLACING INTEGRATING INSTALLING OR RECOVERING SUCH HARDWARE SOFTWARE OR DATA Any disputes arising between manufacturer and customer shall be governed by the law
8. an electrical accident occurs you can then quickly remove power from the system Do not work alone when working with high voltage components Power should always be disconnected from the blade module when removing or installing such system components as the mainboard memory modules and processors When working around exposed electrical circuits another person who is familiar with the power off controls should be nearby to switch off the power if necessary Use only one hand when working with powered on electrical equipment This is to avoid making a complete circuit which will cause electrical shock Use extreme caution when using metal tools which can easily damage any electrical components or circuit boards they come into contact with Do not use mats designed to decrease electrostatic discharge as protection from electrical shock Instead use rubber mats that have been specifically designed as electrical insulators The power supply power cords must include a grounding plug and must be plugged into grounded electrical outlets Power input requires 110 240 VAC depending upon your power supply module Mainboard Battery This battery must be replaced only with the same or an equivalent type recommended by the manufacturer CR2032 Lithium 3V battery Dispose of used batteries according to the manufacturer s instructions WARNING There is a danger of explosion if the onboard battery is installed A upside down which will reverse its polar
9. d for system mainboards to enable maximum efficient air flow through the system It can be configured to fit different sized system mainboards of the same general shape and size The SC846 X9 universal air shroud is optimized for use with Supermicro SC846 series chassis designs and for Supermicro X8DTx X9DRx H8DGx series mainboards See Chapter 3 for configuration details 1 2 Product Checklist of Typical Components The SC846 X9 universal air shroud comes packaged with components and parts as shown in Table 1 1 Table 1 1 SC846 X9 Universal Air Shroud Parts and Components Part Number MCP 310 49003 0N MCP 310 49005 1N MCP 310 39003 1N MCP 310 28005 1N MCP 310 28006 1N MCP 310 39004 1N Description Quantity SC846 Intel DP X9 universal PC air shroud 13 68 x13 12 x13 motherboard SC846 X9 universal air shroud component main body Part A SC836 X9 universal air shroud component moving part Part B X8 air shroud universal component partition Part C X8 universal air shroud component tear drop 55mm part D SC836 X9 universal air shroud component moving part Part E 1 1 1 1 1 be connected f NOTE The default configuration is for Component Parts A B C D and E to all with its component part letter for easy identification V4 NOTE Each individual part for the SC846 X9 universal air shroud is labeled 1 1 SC846 Air Shroud User s Guide 1 3 Features The SC846 X9 universal air
10. elease Date October 3 2011 Unless you request and receive written permission from Super Micro Computer Inc you may not copy any part of this document Information in this document is subject to change without notice Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders Copyright 2011 by Super Micro Computer Inc All rights reserved Printed in the United States of America Preface About this Manual This manual is written for professional system integrators Information Technology professionals service personnel and technicians It provides information for the installation and use of Supermicro s SC846 X9 universal air shroud Installation and maintenance should be performed by experienced professionals only Manual Organization Chapter 1 Introduction The first chapter provides a checklist of the main components included with the SC846 X9 universal air shroud and describes its main features Chapter 2 System Safety You should familiarize yourself with this chapter for a general overview of safety precautions that should be followed when installing and servicing the SC846 X9 universal air shroud Chapter 3 Configuration and Installation Refer here for details on installing and configuring the SC846 X9 universal air shroud on a computer system mainboard SC846 Air Shroud User s Guide Notes Table of Contents C
11. figuration and installation of the SC846 X9 universal air shroud into a server or into a chassis The main section Component Part A is connected to other sections Component Parts B C D and E to make up many possible configurations based upon the sliding positions of the components and locking tabs even more if parts are detached 3 2 SC846 X9 Universal Air Shroud Components Figure 3 1 SC846 X9 Universal Air Shroud Components Table 3 1 SC846 X9 Universal Air Shroud Components Item Description moO W SC846 X9 universal air shroud component main body Part A X9 universal air shroud component moving part Part B X8 air shroud universal component partition Part C X8 universal air shroud component tear drop 55mm Part D X9 universal air shroud component moving part Part E The SC846 X9 universal air shroud comes with the main body and four detachable component partss Figure 3 1 and Table 3 1 See below for details These component parts can be used to create multiple different configurations for use in sytems See Section 3 4 for further details on configurations The SC846 X9 universal air shroud is optimized for use with Supermicro X8DTx X9DRx H8DGx series mainboards 3 1 SC846 Air Shroud User s Guide Component Part B Figure 3 2 Moving Component Part B
12. hapter 1 Introduction 1 1 1 1 OVerVi W ese ee ee iris 1 1 1 2 Product Checklist of Typical Components 1 1 1 S Eeature8 n hin alain anti Ge EG Deed 1 2 1 4 Returning Merchandise for Service 1 2 1 5 Contacting Supermicro ee ee se ek ee Ge GR Re Ge GR RR Ge Ge RR Ge Re 1 3 Chapter 2 System Safety 2 1 2 1 Electrical Safety Precauti0nS ese see ee ee ee RR Re ee GR GR ER ee Ge GR Re 2 1 2 2 General Safety Precautions 2 2 2 3 Electrostatic Discharge Precautions U 2 2 2 4 Operating Precautions 2 2 Chapter 3 Configuration and Installation 3 1 Ke RE EE RE Ann ne 3 1 3 2 SC846 X9 Universal Air Shroud Components 3 1 Component Part Bied utes LEEK eg a eR ee EER ES De SR e n ka 3 2 Component Part Cs c wit yld ER N kak EE EE N ce 3 3 Component Part De ao anal dad EE Ee dik eine si gees ee ayda seya ene k eyek z nek 3 4 Gomponent Paft Eis nadan SE se Ses Pe REK iia EES ae ann ii 3 5 3 3 Removing Breakable Tabs for Cabling cccceeeceeeeeeteeees 3 6 3 4 Configuring the SC846 X9 Universal Air Shroud 3 7 3 5 Installing the SC846 X9 Universal Air Shroud 3 9 SC846 Air Shroud User s Guide Vi Chapter 1 Introduction 1 1 Overview The SC846 X9 universal air shroud is a configurable air shrou
13. ignment slots provided on component part A Component Part D may also be removed out if it is not required see Figure 3 4 Chapter 3 Configuration and Installation Component Part E Figure 3 5 Moving Component Part E TU sad Uy it r il im Lr 4 B 5 20 C0 H N rd The SC846 X9 universal air shroud s Component Part E Figure 3 5 can be moved in and out to resize the X9 universal air shroud s size to fit the mainboard using three sliding positions labeled A B and C The bottom of Component Part E can also be detached to allow for cable access under the air shroud 3 5 SC846 Air Shroud User s Guide 3 3 Removing Breakable Tabs for Cabling Figure 3 6 Removing the Breakable Tabs Breakable Tabs Component Parts A B C and E for the SC846 X9 universal air shroud have breakable tabs that can be permanently removed to allow cabling access if required for your system see Figure 3 6 for details To remove simply cut or break the tabs off from their attachments with a pair of scissors and discard them 3 6
14. ities Mainboard replaceable soldered in fuses Self resetting PTC Positive Temperature Coefficient fuses on the mainboard must be replaced by trained service technicians only The new fuse must be the same or equivalent as the one replaced Contact technical support for details and support 2 1 SC846 Air Shroud User s Guide 2 2 General Safety Precautions Follow these rules to ensure general safety e Keep the area around the server clean and free of clutter e Place the blade module cover and any system components that have been removed away from the system or on a table so that they won t accidentally be stepped on e While working on the system do not wear loose clothing such as neckties and unbuttoned shirt sleeves which can come into contact with electrical circuits or be pulled into a cooling fan Remove any jewelry or metal objects from your body which are excellent metal conductors that can create short circuits and harm you if they come into contact with printed circuit boards or areas where power is present After accessing the inside of the system replace the blade module s cover before installing it back into the blade enclosure 2 3 Electrostatic Discharge Precautions Electrostatic discharge ESD is generated by two objects with different electrical charges coming into contact with each other An electrical discharge is created to neutralize this difference which can damage electronic components and p
15. rinted circuit boards The following measures are generally sufficient to neutralize this difference before contact is made to protect your equipment from ESD Use a grounded wrist strap designed to prevent static discharge Keep all components and printed circuit boards PCBs in their antistatic bags until ready for use e Touch a grounded metal object before removing the board from the antistatic bag Do not let components or PCBs come into contact with your clothing which may retain a charge even if you are wearing a wrist strap Handle a board by its edges only do not touch its components peripheral chips memory modules or contacts e When handling chips or modules avoid touching their pins Put the mainboard and peripherals back into their antistatic bags when not in use For grounding purposes make sure the blade enclosure provides excellent conductivity between the power supplies the blade modules and the mainboard 2 4 Operating Precautions Care must be taken to assure that the cover of the blade unit is in place when the blade is operating to assure proper cooling Out of warranty damage to the blade can occur if this practice is not strictly followed Any drive carrier without a hard drive installed must remain fully installed in the drive bay when the blade module is operating to ensure proper airflow 2 2 Chapter 3 Configuration and Installation 3 1 Overview This chapter covers the con
16. s of Santa Clara County in the State of California USA The State of California County of Santa Clara shall be the exclusive venue for the resolution of any such disputes Super Micro s total liability for all claims will not exceed the price paid for the hardware product FCC Statement This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the manufacturer s instruction manual may cause harmful interference with radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case you will be required to correct the interference at your own expense California Best Management Practices Regulations for Perchlorate Materials This Perchlorate warning applies only to products containing CR Manganese Dioxide Lithium coin cells Perchlorate Material special handling may apply See www dtsc ca gov hazardouswaste perchlorate for further details WARNING HANDLING OF LEAD SOLDER MATERIALS USED IN THIS A PRODUCT MAY EXPOSE YOU TO LEAD A CHEMICAL KNOWN TO THE STATE OF CALIFORNIA TO CAUSE BIRTH DEFECTS AND OTHER REPRODUCTIVE HARM Manual Revison 1 0 R
Download Pdf Manuals
Related Search