Attaching the Sun StorEdgeTM 5210 NAS and
Contents
1. Both the Sun StorEdge 5210 NAS and expansion unit storage should be displayed and the Unconfigured Capacity should be approximately 1680 GB for one expansion unit 3360 GB for two expansion units and 5040 GB for three expansion units 2 Click Add LUN to open the Add LUN dialog box Selected drives are highlighted in blue unselected drives in grey 3 Select 6 drives from the expansion unit bottom box Make sure only 6 drives are highlighted in blue Recommended select 6 drives column 1 and column 2 4 Verify fields are filled in as follows a RAID Level RAID 5 b Controller 0 c Select New Volume add name ch2vol02 5 Click Apply Progress window should briefly open Adding Lun Status for dacld010 Processing Add LUN Making file system The RAID volume will initialize in the background for several hours After it begins you can perform other NAS management tasks but cannot initiate another RAID operation until the current one completes 6 Verify dac d010 Status is Online and RAIDS Capacity is 700025 MB 7 Click Add LUN 8 Select 5 drives from the expansion unit bottom box Make sure only 5 drives are highlighted in blue Recommended select 5 drives column 3 and column 4 except 3rd row 4th columns d RAID Level RAID 5 e Controller 0 f Select New Volume add name ch2vol03 9 Click Apply Progress window should briefly open Adding Lun Status for dacld020 Processing Add LUN Making2. file system The RAID volume will initialize in the background for several hours After it begins you can perform other NAS management tasks but cannot initiate another RAID operation until the current one completes 10 Verify dac1d010 Status is Online and RAID5 Capacity is 560020 MB 11 Click Add HS to open the Add Hot Spare dialog box 12 Select 12th drive in expansion unit 4th column 3rd row 13 Click Apply 14 Verify Hotspare Status is Online Capacity is 140005 MB 15 For any additional expansion units repeat Steps 3 14 and select Controller 1 in Step 4 b The successful RAID setup creates one file storage segment per LUN automatically You may use these new storage volumes immediately Additional storage segments from the available LUNs may be added to them now or as needed in the future to increase their capacity Copyright 2004 Sun Microsystems Inc All rights reserved Use is subject to license terms Third party software including font technology is copyrighted and licensed from Sun suppliers Portions may be derived from Berkeley BSD systems licensed from U of CA Sun Sun Microsystems the Sun logo Sun StorEdge Java and Solaris are trademarks or registered trademarks of Sun Microsystems Inc in the U S and in other countries All SPARC trademarks are used under license and are trademarks or registered trademarks of SPARC International Inc in the U S and in other countries U S Government Rights Commercial
3. unit please refer to instructions on the front of this poster Connecting Three Expansion Units to the Sun StorEdge 5210 NAS Caution connect all SCSI cables power cables and network cables before powering up the systems Always power up the expansion units prior to powering up the Sun StorEdge 5210 NAS Sun StorEdge 5210 NAS with Two RAID Cards D annman Power connector powers module A Power connector 2 powers module B Ne connections Ey ce ORE adanan Connect two expansion units to the NAS head in the following way The top left SCSI connector on the Sun StorEdge 5210 NAS connects to the bottom right SCSI connector on the top expansion unit 1 The bottom right SCSI connector on the Sun StorEdge 5210 NAS connects to the bottom right SCSI connector on the bottom expansion unit 2 The bottom left SCSI connector on both expansion units connects to its top right SCSI connector 3 4 On the expansion units be sure the power switches are off Then for each expansion unit insert the two power cables into the two power connectors and connect them to an AC power source Turn on the power switches All front panel LEDs should turn solid green Caution when you power off the expansion unit wait five seconds before you power it back on If you power the expansion unit off and on too quickly unexpected results may occur On the Sun StorEdge 5210 NAS be sure the front pow
4. use Government users are subject to the Sun Microsystems Inc standard license agreement and applicable provisions of the FAR and its supplements Copyright 2004 Sun Microsystems Inc Tous droits r serv s Distribu par des licences qui en restreignent l utilisation Le logiciel d tenu par des tiers et qui comprend la technologie relative aux polices de caract res est prot g par un copyright et licenci par des fournisseurs de Sun Des parties de ce produit pourront tre d riv es des syst mes Berkeley BSD licenci s par l Universit de Californie Sun Sun Microsystems le logo Sun Sun StorEdge Java et Solaris sont des marques de fabrique ou des marques d pos es de Sun Microsystems Inc aux Etats Unis et dans d autres pays Toutes les marques SPARC sont utilis es sous licence et sont des marques de fabrique ou des marques d pos es de SPARC International Inc aux Etats Unis et dans d autres pays Part Number Num ro de pi ce 817 7513 11 Revision A Date 11 2004 SS Re SUN microsystems Attaching Two or Three Expansion Units If you are connecting a single expansion unit please refer to instructions on the front of this poster Connecting Two Expansion Units to the Sun StorEdge 5210 NAS Caution connect all SCSI cables power cables and network cables before powering up the systems Always power up the expansion units prior to powering up the Sun StorEdge 5210 NAS If you are connecting a single expansion
5. S Re SUN microsystems Attaching the Sun StorEdge 5210 NAS and Expansion Units S Re SUN microsystems If you are using the Sun StorEdge 5210 NAS with one or more expansion units the systems must be fully connected before powering them up Caution always power up the expansion unit prior to powering up the Sun StorEdge 5210 NAS Connecting a Single Expansion Unit to the Sun StorEdge 5210 NAS If you are connecting two or three expansion units please refer to instructions on the back of this poster Caution connect all SCSI cables power cables and network cables before powering up the systems Always power up the expansion units prior to powering up the NAS head Note Once configured as a pair a Sun StorEdge 5210 NAS and 5210 expansion unit must be kept as a pair switching an expansion unit to another NAS head will prevent normal system operation Sun StorEdge 5210 NAS with One RAID Card Bene en connector ER RRR module A ERR qQj 0 Power Network e pag ian ma P a owers Cuo CE m ERSEN EE meie B Expansion Unit The Sun StorEdge 5210 NAS and expansion unit connect through a pair of SCSI cables and ports The left SCSI connector on the Sun StorEdge 5210 NAS connects to the bottom right SCSI connector on the EU 1 The bottom left SCSI connector on the expansion unit connects to its top right SCSI connector 2 as shown in the above illustratio
6. er button behind the front panel is in the off position Check that the network cables are securely connected between the unit and the network Insert the two power cables into the two power connectors and connect them to an AC power source Press the power button The Configuration Wizard will start automatically To configure RAID sets refer to Configuring 5210 Expansion Unit RAID Sets on the front of this poster Refer to the Sun StorEdge 5210 Hardware Installation Configuration and User Guide for more detail on connecting and powering up S amp o SUN microsystems Sun StorEdge 5210 NAS with Two RAID Cards ty ft ty yg ft Network connections a MOM m Power connector powers module A Power connector 2 powers module B Connect three expansion units to the NAS head in the following way The top left SCSI connector on the Sun StorEdge 5210 NAS connects to the bottom right SCSI connector on the top expansion unit 1 The bottom right SCSI connector on the Sun StorEdge 5210 NAS connects to the bottom right SCSI connector on the middle expansion unit 2 The bottom left SCSI connector on the Sun StorEdge 5210 NAS connects to the bottom right SCSI connector on the bottom expansion unit 3 The bottom left SCSI connector on all three expansion units connects to its top right SCSI connector 4 5 6 On the expansion units be sure the power switches are off Then for each expansion unit insert
7. n On the expansion unit be sure the power switches are off Then insert the two power cables into the two power connectors and connect them to an AC power source Turn on the power switches All front panel LEDs should turn solid green Caution when you power off the expansion unit wait five seconds before you power it back on If you power the expansion unit off and on too quickly unexpected results may occur On the NAS head be sure the front power button behind the front panel is in the off position Check that the network cables are securely connected between the unit and the network Insert the two power cables into the two power connectors and connect them to an AC power source Press the power button The Configuration Wizard will start automatically Refer to the Sun StorEdge 5210 Hardware Installation Configuration and User Guide for more detail on connecting and powering up Configuring 5210 Expansion Unit RAID Sets After answering all the questions asked by the Configuration Wizard the Sun StorEdge 5210 NAS will be configured for file sharing using the storage provided by its internal disk drives To add the storage capacity provided by the Expansion Unit open a web browser from a client on the same network Type the address of the Sun StorEdge 5210 NAS in the address location field to access the Web Administrator Then perform the following steps 1 In the navigation panel select RAID gt Manage RAID
8. the two power cables into the two power connectors and connect them to an AC power source Turn on the power switches All front panel LEDs should turn solid green Caution when you power off the expansion unit wait five seconds before you power it back on If you power the expansion unit off and on too quickly unexpected results may occur On the Sun StorEdge 5210 NAS be sure the front power button behind the front panel is in the off position Check that the network cables are securely connected between the unit and the network Insert the two power cables into the two power connectors and connect them to an AC power source Press the power button The Configuration Wizard will start automatically To configure RAID sets refer to Configuring 5210 Expansion Unit RAID Sets on the front of this poster Refer to the Sun StorEdge 5210 Hardware Installation Configuration and User Guide for more detail on connecting and powering up
Download Pdf Manuals
Related Search