Home

Netra X4200 M2 Server Service Manual

1. g moa Power OK LED Sd Service action required LED Input OK Locate button LED Power supply LEDs on each power supply FIGURE C 2 Netra X4200 M2 Server Rear Panel LEDs 132 Netra X4200 M2 Server Service Manual May 2007 Using LEDs to Identify the State of Devices Front and Rear Panel LEDs The seven front panel LEDs FIGURE C 1 are located in the upper left corner of the server chassis Locator LED button Fault Activity Power button Alarm status indicators FIGURE C 3 Front Panel LEDs Appendix C Status Indicator LEDs 133 TABLE C 1 lists and describes the front and rear panel LEDs TABLE C 1 Front and Rear Panel LEDs LED Locator LED and button Fault LED Activity LED Power button Alarm Critical LED Alarm Major LED Alarm Minor LED Alarm User LED Power OK LED Location Color Description front upper white Enables you to identify a particular server The LED is activated left and rear using one of the following methods center e Issuing the setlocator on or off command e Pressing the button to toggle the indicator on or off This LED provides the following indications e Off Normal operating state e Fast blink The server received a signal as a result of one of the preceding methods front upper amber Ifon indicates that service is required The ALOM showfau
2. After a pause the firmware deletes the array Appendix E Serial Attached SCSI BIOS Configuration Utility 199 Note Once a volume has been deleted it cannot be recovered When a RAID 1 volume is deleted the data is preserved on the primary disk The master boot records MBR of other disks in the array are deleted For other RAID types the master boot records of all disks are deleted Locating a Disk Drive There are several ways to physically locate a disk drive as long as the firmware is correctly configured and the drives support disk location a During RAID creation when a disk is set to Yes as part of a RAID volume its Locate LED is enabled When it is set back to No or the RAID volume is created the Locate LED is cleared m Disks can also be located from the SAS Topology screen To locate a disk move the cursor to the disk and press Enter The Locate LED on the disk remains lit until the next key is pressed 200 Netra X4200 M2 Server Service Manual May 2007 Index Numerics 10 100 1000BASE T connector pinouts 142 10 100BASE T connector pinouts 141 A accessory kit contents 9 acoustic noise emission specs Netra X4200 M2 120 Activity LED bezel 134 hard drive 135 Air filter 7 Alarm board 8 alarm board installing 104 removing 103 replacing 103 alarm port 144 pinout 144 antistatic measures performing 31 removing 113 B back panel LED locations 132 Netra X4200 M2 4 battery 8 Netra
3. Appendix E Serial Attached SCSI BIOS Configuration Utility 163 Global Properties Screen To access the Global Properties screen press Alt N while on the Adapter List screen To return to the Adapter List from Global Properties press Alt N again FIGURE E 2 shows an example of the Global Properties screen TABLE E 3 describes the fields in this screen KREKEKKKKKKKKKK KK KKK KKK KKK KKK KK KKK KKK KEK KK KKK KKK KKK KKK KKK KKK KEKE KK KKKKKKKEKKKKKKKKEKK Adapter List Global Properties k 7 Pause When Boot Alert Displayed No Boot Information Display Mode Display adapters amp installed devices x Support Interrupt Hook interrupt the Default 7 Restore Defaults i Esc Exit Menu F1 Shift 1 Help Alt N Adapter List i kkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkk FIGURE E 2 Global Properties Screen TABLE E 3 Global Properties Screen Field Descriptions Field Description Pause When Boot This option specifies whether the BIOS pauses for user Alert Displayed acknowledgement after displaying an alert message during boot To continue after displaying a message select No To wait for the user to press a key select Yes Boot Information This option controls how much information the BIOS displays about Display Mode adapters and devices during boot Possible values are e Display adapters only Display adapters and all devices e Display mi
4. Performing Antistatic Measures 1 Prepare an antistatic surface on which to set parts during removal and installation Place ESD sensitive components such as the printed circuit boards on an antistatic mat The following items can be used as an antistatic mat a Antistatic bag used to wrap a Sun replacement part Chapter 3 Maintaining the Netra X4200 M2 Server 31 a Sun ESD mat part number 250 1088 32 Netra X4200 M2 Server Service Manual May 2007 a Disposable ESD mat shipped with some replacement parts or optional system components 2 Attach an antistatic wrist strap When servicing or removing server components attach an antistatic strap to your wrist and then to button snap grounding post inside the chassis just behind the mass storage assembly see FIGURE 3 10 for the location Then disconnect the power cords from the server Removing the Top Cover 1 Press down on the cover release and using the indent for leverage slide the cover toward the rear of the chassis approximately 0 5 inch 12 mm See FIGURE 3 4 2 Grasp the cover by its rear edge and lift it straight up from the chassis Note When you remove any cover the intrusion switch that is on the front I O board automatically powers down the system to standby mode FIGURE 3 4 Removing the Top Cover Opening the Front Bezel Chapter 3 Maintaining the Netra X4200 M2 Server 33 1 Locate the green tabs on either side of the bezel and pull t
5. Preface xiii xiv Netra X4200 M2 Server Service Manual May 2007 CHAPTER 1 Introduction to the Netra X4200 M2 Server This chapter provides an overview of the Netra X4200 M2 server including features and orderable components Features of the Server The Netra X4200 M2 server is designed to take full advantage of the exceptional power and performance of the AMD Opteron processor The server includes an extensive set of reliability availability and serviceability RAS features The server also provides a remote Integrated Lights Out Manager ILOM Service Processor function including remote boot and remote software upgrades TABLE 1 1 summarizes the features of the Netra X4200 M2 server TABLE 1 1 Summary of Netra X4200 M2 Server Features Feature or Component Netra X4200 M2 Server CPU Up to two Next Generation AMD64 Opteron 200 Series dual core processors 1Mbyte L2 cache per core Memory Up to eight DIMMs up to 32GB capacity Hard disk drives HDDs Qualified DIMMs e 667 MHz Registered ECC DDR2 DIMMs PC5300 Up to four Serial Attached SCSI 2 SAS or 4 SAS hot pluggable HDDs 2 5 inch or 63 5 mm TABLE 1 1 Summary of Netra X4200 M2 Server Features Continued Feature or Component Netra X4200 M2 Server Baseboard Motorola MPC8248 at 266MHz management controller BMC RAID options Network I O PCI I O Other I O Removable media devices Power Alarms Fans Four chan
6. TABLE 3 1 Supported DIMM Configurations for Netra X4200 M2 Slot A1 Slot B1 Slot AO Slot BO otal Memory Per CPU 1 GB 1 GB 0 0 2 GB 1 GB 1 GB 1 GB 1 GB 4 GB 2 GB 2 GB 1 GB 1 GB 6 GB 4 GB 4 GB 1 GB 1 GB 10 GB 2 GB 2 GB 0 0 4 GB 2 GB 2 GB 2 GB 2 GB 8 GB Chapter 3 Maintaining the Netra X4200 M2 Server 73 74 TABLE 3 1 Supported DIMM Configurations for Netra X4200 M2 Continued Slot A1 lot B1 lot AO lot BO otal Memory Per CPU 4 GB GB GB GB 12 GB 4 GB GB GB 4 GB GB GB GB 16 GB 4 Set the DIMM aside on an antistatic mat 5 Repeat steps 3 and 4 for all DIMMs to be removed 6 Consider your next step a If you removed the DIMMs as part of another procedure return to that procedure If you are to install DIMMs continue to Installing a DIMM on page 74 If you are to only remove DIMMs a Install the DIMM CPU duct See Installing the DIMM CPU Duct on page 69 b Perform the following tasks to bring the server back online a Installing the Top Cover on page 126 a Removing Antistatic Measures on page 127 a Reinstalling the Server Chassis in the Rack on page 127 a Reconnecting Cables to the Server on page 130 a Powering On the Server on page 131 Installing a DIMM 1 Flip the DIMM CPU duct open DIMMs are located underneath See FIGURE 3 49 Note Locate DIMM numbering on the bottom of the air duct 2 Ensure that the DIMM slot ejectors at each
7. Configuration Utility Screens All SAS BIOS Configuration Utility screens are partitioned into the following areas starting at the top of the screen a Header Area This area lists static information text including the product title and version m Menu Area This area lists the current screen title and controller information when on screens other than Adapter List m Main Area This is the main area for presenting data This area has a cursor for item selection horizontal scrolling and vertical scrolling The horizontal and vertical scroll bars appear here if needed m Footer Area This area provides general help information text Appendix E Serial Attached SCSI BIOS Configuration Utility 159 Note The screens shown in this appendix are examples The version numbers and the screen items shown are subject to change over the life of the product User Input Keys The general key inputs that are listed in TABLE E 1 apply on all screens of the SAS BIOS Configuration Utility TABLEE 1 User Input Keys Key Definition Description F1 Help Arrow keys Move cursor Home End Select item Change item Esc Abort Exit Enter Execute lt item gt Context sensitive help for the field in which the cursor is positioned Up down left right movement to position the cursor Select the item in which the cursor is positioned Items with values in brackets are modifiable Numeric keypad and numeric keypad
8. Field Description Device Identifier The ASCII device identifier string extracted from the device s inquiry data SAS Address The SAS address of this device 172 Netra X4200 M2 Server Service Manual May 2007 TABLEE 7 Device Verify Screen Field Descriptions Continued Field Description Serial Number The serial number of this device Elapsed Time The total time elapsed since the Format or Verify operation started Percent Complete Graphical status bar that shows the current completion status of the operation If the Logical Block Addresses LBAs can be reassigned or need to be reassigned the following prompt appears Reassign the block Yes No All nonE Cancel The reassignment options are as follows m Yes Reassign only this block If another block needs to be reassigned in the future display the prompt again No Do not reassign this block If another block needs to be reassigned in the future display the prompt again a All Reassign the current block and automatically reassign other blocks that need it without displaying the prompt again m None Do not reassign the current block and do not automatically reassign any other blocks that need it Do not display the prompt again m Cancel Do not reassign anything and stop the verification process Advanced Adapter Properties Screen The Advanced Adapter Properties screen see FIGURE E 11 allows you to view and modify infrequently accessed a
9. D4 3 3V SB D5 S_INT Alert D6 POK 3 3V Standby Output Ground Analog fan control voltage input Ground 3 3V Standby Output EEPROM Serial Data I O Enable for main supply output Ground Fan tach output 2 pulses per rev Ground 3 3V Standby Output EEPROM Serial Clock Input Input voltage above minimum spec Present active low PU No Connect Tach_2 if two fan design Ground 3 3V Standby Output Intrusion switch alert Output voltages within spec PU Fan Module Connector The fan module connectors and their corresponding descriptions are shown in the figure and table in this section 154 Netra X4200 M2 Server Service Manual May 2007 Pin4 Pin 3 Note the keyed shapes of the pins for orientation Pin 2 Pin 1 FIGURE D 12 Fan Module Connectors Note Fan modules in Netra X4200 M2 servers each contain one 80 mm fan Fan A The same connector is used for both types of fan modules with slightly different assignments to connector pins as shown in TABLE D 12 TABLE D 12 Fan Module Connector Pinouts Pin Number Pin Name Description 1 12V 2 GND 3 Fan A Tach 4 Fan B Tach 12V power to Fan A and to Fan B in Sun Fire X4100 fan modules Ground for Fan A and for Fan B in Sun Fire X4100 fan modules Fan A tachometer sensor Fan B tachometer sensor for Sun Fire X4100 fan modules Presence sensor tied to Pin 2 for Netra X4200 fan modules Appendix D Connector Pinouts 155 15
10. Removing the Top Cover on page 33 a Removing the PCI Tray and PCI E Ribbon Cables on page 34 2 Remove the DIMM CPU duct See Removing the DIMM CPU Duct on page 68 3 Remove the system fan assembly See Removing the System Fan Assembly on page 54 4 Loosen the thumbscrew of the LED board and swing the board out to the left FIGURE 3 40 innana a ea FIGURE 3 40 Removing the LED Board From the Chassis 5 Carefully lift the LED board and cable from the cable clips 6 Disconnect the cable from the LED board FIGURE 3 41 Chapter 3 Maintaining the Netra X4200 M2 Server 63 FIGURE 3 41 Disconnecting the Cable From the LED Board 7 Set the LED board aside on an antistatic mat 8 Continue to Installing the LED Board on page 64 Installing the LED Board 1 Remove the replacement LED board from its packaging and place the board on an antistatic mat 2 Connect the cable to the LED board FIGURE 3 42 FIGURE 3 42 Connecting the Cable to the LED Board 3 Insert the tab on the LED board into the slot on the chassis FIGURE 3 43 san Se ae 64 Netra X4200 M2 Server Service Manual May 2007 FIGURE 3 43 Inserting the LED Board Tab 4 Swing the LED board right to the chassis and tighten the thumbscrew FIGURE 3 44 FIGURE 3 44 Securing the LED Board to the Chassis 5 Route the LED board cable back into the cable guides 6 Install the system fan assembly See
11. 121 The message BMC Responding is displayed at the end of POST Redirecting Console Output Use these instructions to access the service processor and redirect the console output so that the BIOS POST codes can be read 1 Initialize the BIOS Setup utility by pressing the F2 key while the system is performing the power on self test POST 2 When the BIOS Main Menu screen is displayed select Advanced 121 3 When the Advanced Settings screen is displayed select IPMI 2 0 Configuration 4 When the IPMI 2 0 Configuration screen is displayed select the LAN Configuration menu item 5 Select the IP Address menu item The service processor s IP address is displayed using the following format Current IP address in BMC xxx xxx xxx xxx 6 Start a web browser and type the service processor s IP address in the browser s URL field 7 When you are prompted type a user name and password as follows User name root Password changeme 8 When the ILOM Service Processor GUI screen is displayed click the Remote Control tab 9 Click on the Redirection tab 10 Set the color depth for the redirection console at either 6 or 8 bits 11 Click on the Start Redirection button The javaRConsole window appears and prompts you for your user name and password again 12 When you are prompted type a user name and password as follows User name root Password changeme The current POST screen is displayed Chang
12. 2007 FIGURE 3 61 Removing the Motherboard Assembly From the Chassis 7 Set the motherboard assembly aside on an antistatic mat 8 Continue to Installing the Motherboard Assembly on page 86 Note After you replace the motherboard FRU you must use the servicetool command to update FRU information about the motherboard See Servicetool FRU Update Procedure on page 117 Chapter 3 Maintaining the Netra X4200 M2 Server 85 Installing the Motherboard Assembly 1 Remove the replacement motherboard assembly from its packaging and place the assembly on an antistatic mat 2 Lower the left edge of the motherboard assembly into the chassis then the entire board and while slightly elevated slide the motherboard assembly to the back of the chassis FIGURE 3 62 carefully seating the rear I O connectors into the rear gasketing FIGURE 3 62 Installing the Motherboard Assembly Into the Chassis 3 Align the motherboard assembly screw holes over the chassis standoffs 4 Install the two bus bar screws and five other screws FIGURE 3 60 5 Reconnect the cables to the following connectors on the motherboard assembly a Flex Circuit J7 a Front I O J23 86 Netra X4200 M2 Server Service Manual May 2007 6 Install the following components Graphics Redirect and Service Processor GRASP board See Installing the GRASP Board on page 67 Alarm board See Replacing the Alarm Board on page 103
13. 95 The following LEDs are lit when a power supply fault is detected m Front and rear Service Required LEDs a Amber Failure LED on the faulty power supply If a power supply fails and you do not have a replacement available leave the failed power supply installed to ensure proper airflow in the server Removing a Power Supply 1 Identify which power supply requires replacement FIGURE 3 70 Latch FIGURE 3 70 Power Supplies Locations A lighted amber LED on a power supply indicates that a failure was detected You can also use the showfaults command at the sc gt prompt 2 Disconnect the power cord from the faulty power supply 3 Grasp the power supply handle and push the power supply latch to the right FIGURE 3 70 4 Pull the power supply out of the chassis FIGURE 3 71 96 Netra X4200 M2 Server Service Manual May 2007 FIGURE 3 71 Removing a Power Supply From the Chassis 5 Continue to Installing a Power Supply on page 97 Installing a Power Supply 1 Remove the replacement power supply from its packaging and place the supply on an antistatic mat Align the replacement power supply with the empty power supply bay Slide the power supply into bay until it is fully seated FIGURE 3 72 Chapter 3 Maintaining the Netra X4200 M2 Server 97 FIGURE 3 72 Installing a Power Supply Into the Chassis 4 Reconnect the power cord to the power supply 5 Verify that the amber LED on the
14. 95054 Etats Unis Tous droits r serv s Sun Microsystems Inc a les droits de propri t intellectuels relatants la technologie qui est d crit dans ce document En particulier et sans la limitation ces droits de propri t intellectuels peuvent inclure un ou plus des brevets am ricains num r s a http www sun com patents et un ou les brevets plus suppl mentaires ou les applications de brevet en attente dans les Etats Unis et dans les autres pays Ce produit ou document est prot g par un copyright et distribu avec des licences qui en restreignent l utilisation la copie la distribution et la d compilation Aucune partie de ce produit ou document ne peut tre reproduite sous aucune forme par quelque moyen que ce soit sans l autorisation pr alable et crite de Sun et de ses bailleurs de licence s il y ena Le logiciel d tenu par des tiers et quicomprend la technologie relative aux polices de caract res est prot g par un copyright et licenci par des fournisseurs de Sun Des parties de ce produit pourront tre d riv es des syst mes Berkeley BSD licenci s par l Universit de Californie UNIX est une marque d pos e aux Etats Unis et dans d autres pays et licenci e exclusivement par X Open Company Ltd Sun Sun Microsystems le logo Sun Java AnswerBook2 docs sun com Solaris et Netra sont des marques de fabrique ou des marques d pos es de Sun Microsystems Inc aux Etats Unis et dans d autres pay
15. Assembly 1 Remove the replacement hard drive fan assembly from its packaging and place the assembly on an antistatic mat 2 Lower the hard drive fan assembly down and slide the hard drive fan bracket back so that the tabs enter the slots FIGURE 3 37 60 Netra X4200 M2 Server Service Manual May 2007 Allin FIGURE 3 37 Lowering the Hard Drive Fan Assembly 3 Pivot the hard drive fan bracket forward until it clicks FIGURE 3 38 FIGURE 3 38 Securing the Hard Drive Fan Bracket 4 Connect the hard drive fan assembly cable to the power board at connector J5 FIGURE 3 39 Chapter 3 Maintaining the Netra X4200 M2 Server 61 FIGURE 3 39 Connecting the Hard Drive Fan Assembly Cable 5 Route the hard drive fan assembly cable back into the cable guides 6 Perform the following tasks to bring the server back online 62 Installing the Top Cover on page 126 Removing Antistatic Measures on page 127 Reinstalling the Server Chassis in the Rack on page 127 Reconnecting Cables to the Server on page 130 Powering On the Server on page 131 Replacing the LED Board Removing the LED Board 1 Prepare the server for LED board removal Powering Off the Server on page 28 Disconnecting Cables From the Server on page 29 Removing the Server From the Rack on page 30 Performing Antistatic Measures on page 31 Netra X4200 M2 Server Service Manual May 2007 a
16. DIMMs See Installing a DIMM on page 74 Fan assembly See Installing the System Fan Assembly on page 55 DIMM CPU duct See Installing the DIMM CPU Duct on page 69 Cables for PCI E See Reconnecting Cables to the Server on page 115 Cable hold down bracket See Removing the PCI E Cable Hold Down Bracket on page 36 PCI tray Removing the PCI Tray and PCI E Ribbon Cables on page 34 Top cover Removing the Top Cover on page 33 Perform the following tasks to bring the server back online Installing the Top Cover on page 126 Removing Antistatic Measures on page 127 Reinstalling the Server Chassis in the Rack on page 127 Reconnecting Cables to the Server on page 130 Powering On the Server on page 131 Once installed the new motherboard needs to have chassis system dynamic send number part number information programmed as well as updating to the Netra X4200 specific BIOS image using the servicetool update procedure See Servicetool FRU Update Procedure on page 117 Chapter 3 Maintaining the Netra X4200 M2 Server 87 Replacing a PCI X Card Caution The total power consumption of all PCI cards combined is not to exceed 80 watts The maximum power of any one PCI card is 25 watts Removing a PCI X Card 1 Prepare the server for PCI X card removal See m Powering Off the Server on page 28 a Disconnecting Cables From t
17. DVD Drive 3 Press the DVD drive in until it seats and release the tab Ensure that the DVD device fully seats into the mating DVD board 4 Close the bezel 5 Consider your next step a If you installed the DVD drive as part of another procedure return to that procedure a Otherwise perform the following tasks to bring the server back online a Installing the Top Cover on page 126 a Removing Antistatic Measures on page 127 a Reinstalling the Server Chassis in the Rack on page 127 42 Netra X4200 M2 Server Service Manual May 2007 a Reconnecting Cables to the Server on page 130 a Powering On the Server on page 131 Replacing a Hard Drive The hard disk drives in the server are hot pluggable but this capability depends on how the hard drives are configured To hot plug a drive you must take the drive offline prevent any applications from accessing it and remove the logical software links to it before you can safely remove it The following situations inhibit the ability to perform hot plugging of a drive a The hard drive provides the operating system and the operating system is not mirrored on another drive a The hard drive cannot be logically isolated from the online operations of the server If your drive falls into the conditions listed above you must shut down the system before you replace the hard drive See Powering Off the Server on page 28 Note Replacing a har
18. Descriptions Field Device Identifier Discovery Status Device Info Negotiated Link Speed Maximum Link Speed Target Capabilities Initiator Capabilities Description The ASCII device identifier string extracted from the device s inquiry data The status of SAS topology discovery on this directly attached PHY or on an expander This field is only an indicator of an error being encountered For specific details and the error value see the Expander Properties page for expanders and the PHY Properties page for directly attached PHYs Indicates whether a device is SAS or SATA and whether the device has been selected as the boot device The negotiated link speed for this PHY in Gbits s This field also indicates whether the PHY has been disabled The maximum hardware link rate possible for this PHY in Gbits s The target capabilities for this device The following acronyms are used e SSP Serial SCSI Protocol e SMP Serial Management Protocol The initiator capabilities for this device The following acronyms are used e SSP Serial SCSI Protocol e SMP Serial Management Protocol Device Properties Screen The Device Properties screen displays information about a specific device as shown in FIGURE E 9 To access this screen press Alt D on the SAS Topology screen when the cursor is on the Device Identifier field of a device Press Alt N or Alt P at any time while on this screen to cycle to the next
19. E 13 PHY Properties Screen TABLE E 10 PHY Properties Screen Field Descriptions Field Description PHY The PHY number for which this information applies SAS Port The associated SAS Port 0 to N as configured on this adapter Link Status The PHY link status Possible values are e Enabled Unknown Link Rate e PHY Disabled e Enabled negotiation failed e Enabled 1 5 Gbps e Enabled 3 0 Gbps 180 Netra X4200 M2 Server Service Manual May 2007 TABLE E 10 PHY Properties Screen Field Descriptions Continued Field Description Discovery Status A 32 bit hexadecimal value indicating the discovery status for the PHY or expander Currently defined values are e Discovery Completed Successfully 0x00000000 e Loop Detected 0x00000001 e Unaddressable Device Exists 0x00000002 e Multiple Ports 0x00000004 e Expander Error 0x00000008 SMP Timeout 0x00000010 e Out of Route Entries 0x00000020 SMP Response Index Does Not Exist 0x00000040 SMP Response Function Failed 0x00000080 e SMP CRC Error 0x00000100 Device Identifier The ASCII device identifier string extracted from the device s inquiry data Scan Order The scan order for this device This is the equivalent of a SCSI ID for parallel SCSI Device Information Indicates whether a device is SAS or SATA SAS Address The SAS address of this device Link Error Settings Invalid DWORDs The number of invalid DWORDs that have been received outside of PHY rese
20. FRU configuration has been updated Updating FRUs done flash root SUNSP00144F3A22D5 Netra X4200 M2 Server Service Manual May 2007 Chapter 3 Maintaining the Netra X4200 M2 Server 119 120 Netra X4200 M2 Server Service Manual May 2007 APPENDIX A System Specifications This appendix contains physical power environmental and acoustic noise emission specifications for the Netra X4200 M2 server Netra X4200 M2 Specifications TABLE A 1 Netra X4200 M2 Physical Specifications Specification Value Width 17 4 inches 442 mm Height 3 5 inches 89 mm Depth 20 inches 508 mm Weight 37 2 pounds 17 kg TABLE A 2 Netra X4200 M2 Power Specifications Specification Value DC Power 48VDC or 60VDC 12 7A at 48VDC 10 2A at 60VDC AC Power 100 240 VAC 50 60 Hz Maximum input 3 2 A current at 200 to 240 VAC 119 TABLE A 2 Netra X4200 M2 Power Specifications Continued Specification Value Maximum input 6 5 A current at 100 to 120 VAC Maximum power 550 W Maximum output supply current of 500 mA each USB port TABLE A 3 Netra X4200 M2Environmental Specifications Specification Value Temperature 41 104 F operating 5 40 C Temperature non 40 to 70 C 40 to 158 F operating relative humidity up to 93 noncondensing 38 C 100 4 F max wet bulb Temperature 40 to 70 C 40 to 158 F storage Humidity 5 85 non condensing Short
21. ILOM web GUI using root as the user name and changeme as the password Refer to the Integrated Lights Out Manager Administration Guide 819 1160 10 Change the default password to a password of your choice 11 Repeat Step 1 through Step 8 to remove the J12 jumper Remove the jumper in Step 5 rather than inserting it Note If you do not remove the J12 jumper the ILOM SP and BIOS passwords will be reset every time you power cycle the server Chapter 2 Powering On and Configuring BIOS Settings 21 20a n 3 an Clear CMOS header pins J12 jumper FIGURE 2 6 Clear CMOS and J12 Jumper Locations on the Motherboard 22 Using the Clear CMOS Jumper You can use the Clear CMOS jumper to clear the server s CMOS settings in the event of a system hang For example if the server hangs because of incorrect settings and will not boot use this jumper to invalidate the settings and reboot with defaults 1 Shut down the server to standby power mode by using a ballpoint pen or other stylus to press and release the recessed Power button on the front panel See Powering Off the Server on page 14 2 Disconnect the AC or DC power cords from the server Netra X4200 M2 Server Service Manual May 2007 Caution Before handling components attach an ESD wrist strap to the grounding post that is built into the rear of the chassis see FIGURE 1 3 for the location The system s print
22. LBAs as described in the text following TABLE E 7 Appendix E Serial Attached SCSI BIOS Configuration Utility 171 Device Verify Screen To access the Device Verify screen press Enter on the appropriate field on the Device Properties screen This screen includes an Elapsed Time and status bar which begins incrementing when the operation is started and which shows the current progress of the operation When the Device Verify screen appears see FIGURE E 10 press Enter to begin the verification process You can press Esc at any time to cancel the verification process TABLE E 7 describes the fields of the screen KREKKKKKKKKEKKK KKK KKK KK KK KEK KKK KKK KK KEK KEK KKK KEK KKK KKK KEKE KKK KK RK KKK KKK KRKKEKKKKKK KK KEKE Device Verify SAS1064 i Device Identifier SEAGATE ST936701LSUN36G 0456 z SAS Address 5000C500 001047C9 2 x Serial Number 39000SZC 3LC All sectors on the device will be verified 7 Press Enter to continue or any other key to cancel k Elapsed Time 00 00 00 Percent i Complete 0 100 j KKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKE kkkkxkxkkxkxkkxkxkkkkkxkxkkxkxkkxkxkkkxkkxkxkkkxkkkxkkkkkkxkkkkkkkkxk Esc Exit F1l Help Alt M More Keys kkkkxkxkkxkxkkxkxkkxkxkkxkxkkkkkxkkkkxkkkkkkkkxkkkkkkxkkkkkkkxkkkkkkkkkkkkxkkkkkkkkkkkkkkkkkkkkxk FIGURE E 10 Device Verify Screen TABLE E 7 Device Verify Screen Field Descriptions
23. Pin Number Signal Name 1 NA 2 NA 3 NA 4 NA 5 NA 6 NA 7 GND 8 GND 9 NA 10 NA 11 GND 12 GND 13 FRONT_LOCATE_L 14 NA 15 GND 16 GND 17 NA 18 3 3 V AUX 19 GND 20 NA 21 SP_I2C_CLK 22 POWER_BUTTON_L 23 SP_I2C_DAT 152 Netra X4200 M2 Server Service Manual May 2007 TABLE D 10 Front I O Interconnect Cable Connector Pinouts Continued Pin Number Signal Name 24 FRONT_IO_INT_L 25 FR_IO_PRESENT_L 26 VDD_RTC Power Supply Connector The power supply connector pins and their corresponding descriptions are shown in the figure and table in this section PB RH1 PB RH6 DNWLY FIGURE D 11 Power Supply Connector TABLE D 11 Power Supply Connector Pinouts Pin Number Pin Name Description PB RH1 12V RET Main Power Return PB RH2 12V RET Main Power Return PB RH3 12V RET Main Power Return PB RH4 12V 12V Power Output PB RH5 12V 12V Power Output PB RH6 12V 12V Power Output Al PS_KILL Turns off both main and standby outputs A2 Current Share Current share signal A3 Return Ground A4 3 3V SB 3 3V Standby Output A5 PS A0 EEPROM Address Bit 0 Input Appendix D Connector Pinouts 153 TABLE D 11 Power Supply Connector Pinouts Continued Pin Number Pin Name Description A6 3 3V SB Bl Return B2 Fan_Cntl B3 Return B4 3 3V SB B5 SDA B6 PS_ON C1 Return C2 Tach _1 C3 Return C4 3 3V SB C5 SCL C6 VIN_GOOD D1 PS_Present D2 NC D3 Return
24. PnP Boot Security Chipset and Exit Use the left and right arrow keys to move sequentially back and forth through the seven screens Fields that can be reconfigured are displayed in color All other fields are not configurable Use the up and down arrow keys to scroll through a screen s menu Use the Tab key to move back and forth across columns Changing the Configuration of a BIOS Menu Item You can change the BIOS configuration using several different interfaces m Use a USB keyboard and mouse and a VGA monitor connected directly to the server m Use the remote video console of the ILOM Service Processor and redirect the server s console output See Redirecting Console Output on page 121 TABLE 2 1 Local to Remote Key Mapping Local Keyboard Remote Keyboard Local Keyboard Remote Keyboard F1 Ctrl Q F9 Ctrl O F2 Ctrl E F10 Ctrl S F7 Ctrl A F12 Ctrl N F8 Ctrl P Note Function keys only work when you are using a local connection When you are changing a BIOS configuration remotely you will need to map your keyboard appropriately Chapter 2 Powering On and Configuring BIOS Settings 15 16 To change the system s parameters enter the BIOS Setup utility by pressing the F2 key while the system is performing the power on self test POST POST testing is indicated when the Power OK LEDs on the front and back panels go into slow blink mode Highlight the field to be modified using the arrow and Ta
25. Remove the replacement PCI E card from its packaging and place the card onto an antistatic mat 4 Ifa filler panel is installed in the PCI tray slot remove it 5 Lower the PCI E card into position on the PCI tray then slide it to the right to seat it into the connector FIGURE 3 69 Netra X4200 M2 Server Service Manual May 2007 L FIGURE 3 69 Installing the PCI E Card Into the PCI Tray 6 Tighten the captive PCI E card securing screw and adjust the green retention latch 7 Perform the following tasks to bring the server back online a Installing the PCI Tray on page 108 a Installing the Top Cover on page 126 m Removing Antistatic Measures on page 127 a Reinstalling the Server Chassis in the Rack on page 127 a Reconnecting Cables to the Server on page 130 a Powering On the Server on page 131 i Replacing a Power Supply The server s redundant hot pluggable power supplies enable you to remove and replace a power supply without shutting the server down provided that the other power supply is online and working Caution It is a violation of UL rules to add a DC power supply into a chassis that does not have the DC label indicating the correct safety information There is no functional difference that would prevent this aside from the DC label Caution Do not mix AC and DC power supplies in the same server Chapter 3 Maintaining the Netra X4200 M2 Server
26. Size MB 69618 Scan Device Identifier RAID Hot Drive Pred Size ID Disk Spr Status Fail MB 2 FUJITSU MAV2073RCSUN72G 0301 Yes No Primary aap 70007 3 FUJITSU MAV2073RCSUN72G 0301 Yes No Secondary 70007 x Esc Exit Menu F1 Shift 1 Help Space Select disk for array or hot spare C Create array KKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKK FIGURE E 15 Create New Array Screen TABLE E 11 Create New Array Screen Field Descriptions Field Description Array Type The type of array being created IM or IS Array Size The size of the array in Mbytes Scan ID The order in which devices are scanned Device Identifier The ASCII device identifier string extracted from the device s inquiry data 184 Netra X4200 M2 Server Service Manual May 2007 TABLE E 11 Create New Array Screen Field Descriptions Continued Field Description RAID Disk Specifies whether the disk is part of a RAID array Yes or No This field is grayed out under the following conditions e The disk does not meet the minimum requirements for use in a RAID array e The disk is not large enough to mirror existing data on the primary drive e This disk has been selected as the Hot Spare for the RAID array Hot Spr Specifies whether the disk is the Hot Spare for a RAID array Yes or No RAID arrays are not required to h
27. X4200 M2 Server Orientation 3 Netra X4200 M2 Server Front Panel Features 3 Netra X4200 M2 Server Rear Panel Features 4 Netra X4200 M2 Server Components 5 Accessory Kit 9 Powering On and Configuring BIOS Settings 11 Powering On the Server 12 Powering Off the Server 14 Configuring BIOS Settings 15 Changing the Configuration of a BIOS Menu Item 15 BIOS Considerations 16 Peripheral Component Interconnect PCI Card Slot Booting Priority 16 Ethernet Port NIC Device and Driver Naming 17 Netra X4200 M2 Server NIC Naming 17 BIOS Option ROM Size Limitation 18 AMD PowerNow Feature Disabled by Default 18 Descriptions of the BIOS Setup Screens 18 Resetting ILOM and BIOS Passwords 20 Using the Clear CMOS Jumper 22 Using the Reset and NMI Switches 23 Updating the BIOS 24 Power On Self Test POST 24 3 Maintaining the Netra X4200 M2 Server 25 Tools and Supplies Needed 26 Locations of the Netra X4200 M2 Components 26 Starting the Maintenance Procedures 28 Powering Off the Server 28 Disconnecting Cables From the Server 29 Removing the Server From the Rack 30 Performing Antistatic Measures 31 Removing the Top Cover 33 Opening the Front Bezel 33 Maintaining the PCI Tray 34 Removing the PCI Tray and PCI E Ribbon Cables 34 Removing the PCI E Cable Hold Down Bracket 36 Replaceable Component Procedures 37 Replacing the Battery 38 Replacing the DVD Drive 40 Removing the DVD Drive 40 Installing the DVD Drive 42 Replacing a Hard Drive 43 Removin
28. a migration The first disk will be mirrored onto the second disk so the data you want to keep must be on the first disk added to the volume Data on all other disks will be lost As disks are added the Array Size field will change to reflect the size of the new volume There are several limitations when creating a RAID 1 volume a All disks must be SAS with SMART support a Disks must have 512 byte blocks and must not have removable media a There must be two drives in a valid volume 6 Optional Add a hot spare to the volume by moving the cursor to the Hot Spare column and pressing the key key or space bar 7 When the volume has been fully configured press C and select Save Changes then exit this menu to commit the changes The Configuration Utility will pause while the array is being created Note RAID 1 provides protection against the failure of a single disk When a disk fails it is rebuilt to a hot spare if one is available This can greatly increase the level of protection that RAID 1 provides Note Even though multiple volumes can be created the hot spare is a global hot spare Only one active hot spare is allowed for all volumes Managing Hot Spares Follow these steps to add a hot spare to a RAID 1 volume 1 Select Manage Hot Spare 2 Select a disk from the list by pressing the key key or space bar Note A hot spare must be valid RAID disk as defined in Creating a RAID 1 Vol
29. amp SUN microsystems Netra X4200 M2 Server Service Manual Sun Microsystems Inc www sun com Part No 820 0063 11 May 2007 Revision A Submit comments about this document at http www sun com hwdocs feedback Copyright 2007 Sun Microsystems Inc 4150 Network Circle Santa Clara California 95054 U S A All rights reserved Sun Microsystems Inc has intellectual property rights relating to technology fiat is described in this document In particular and without limitation these intellectual property rights may include one or more of the U S patents listed at http www sun com patents and one or more additional patents or pending patent applications in the U S and in other countries This document and the product to which it pertains are distributed under licenses restricting their use copying distribution and decompilation No part of the product or of this document may be reproduced in any form by any means without prior written authorization of Sun and its licensors if any Third party software including font technology is copyrighted and licensed from Sun suppliers Parts of the s produet may be derived from Berkeley BSD systems licensed from the University of California UNIX is a registered trademark in the U S and in other countries exclusively licensed through X Open Company Ltd Sun Sun Microsystems the Sun logo Java AnswerBook2 docs sun com Solaris and Netra are trademarks or registered trad
30. connection Right LED Green Link Activity indicator e Steady On a link is established e Blinking there is activity on this port e Off No link is established Note The NET MGT port only operates in 100 Mbps or 10 Mbps so the speed indicator LED can be green or off never amber Internal Status Indicator LEDs The Netra X4200 M2 servers have internal status indicator LEDs for the fan modules the DIMM slots the CPUs and the GRASP board FIGURE C 5 shows the locations of the internal LEDs TABLE C 5 describes the LED behavior Note To see the CPU LEDs or the GRASP board LED you must put the server in standby power mode shut down with the front panel Power button but do not disconnect the AC or DC power cords 136 Netra X4200 M2 Server Service Manual May 2007 Back panel of server DIMM SW2 GRASP board power status LED on the GRASP board DIMM 3 DIMM 1 NOTE PCI Hold Down DIMM 2 Bracket removed DIMM 0 DIMM fault LEDs in DIMM ejector levers Location of CPU LEDs on the motherboard Fan module fault LEDs on fan modules Front panel of server FIGURE C 5 Netra X4200 M2 Internal Status LED Locations TABLE C 5 Internal LED Functions LED Name Description DIMM Fault LED This LED has two states The ejector levers on the e Off DIMM is operating properly DIMM slots are the LEDs e Lit amber DIMM has failed CPU Fault LED This LED has two states on m
31. different interfaces and operating systems Netra X4200 M2 Server NIC Naming FIGURE 2 4 illustrates the default naming used by the various operating systems for the four NICs shown in FIGURE 2 3 BIOS Solaris 10 Red Hat Linux SuSE Linux Windows 2003 slot slot e1000 e1000 ethO eth1 eth2 eth3 net3 net4 110 111 gO gi slot slot nge1 eth2 eth3 etho eth1 net2 108 109 FIGURE 2 4 Netra X4200 M2 NIC Naming Netra X4200 M2 Server NIC Booting Priority The order in which the BIOS detects the Ethernet ports during bootup and the corresponding drivers that control those ports are listed below 1 NET 0 Nvidia NGE 0 2 NET 1 Nvidia NGE 1 3 NET 2 Intel E1000 G0 4 NET 3 Intel E1000 G1 Chapter 2 Powering On and Configuring BIOS Settings 17 18 BIOS Option ROM Size Limitation The BIOS Option ROM is 128 Kbytes Of these 128 Kbytes approximately 80 Kbytes are used by the VGA controller the LSI controller and the onboard network interfaces Approximately 48 Kbytes remain for the Option ROM AMD PowerNow Feature Disabled by Default The AMD PowerNow feature which is accessed from the BIOS Setup utility Advanced menu is disabled by default on Netra X4200 M2 servers If you want to enable this feature review the Netra X4200 M2 Server Product Notes 820 0067 for any outstanding known issues for your operating system Descriptions of the BIOS Setup Screens TABLE 2 2 contains summary descriptions of the
32. in this chapter Netra X4200 M2 Server Service Manual May 2007 Flex circuit under cable retainer Hard disk drive backplane Power supplies 2 Power distribution board Mass storage assembly DVD drive Pa N Hard drives vA 4 or 2 om DIMMs up to 4 for each CPU Goldfinger PCB PCI E Ribbon System fans Cables ia Fan Tray 0 Graphics Redirect and Service Processor GRASP board Alarm board Battery Front panel Motherboard CPUs and heatsinks 2 indicator board DIMM LED button FIGURE 3 1 Netra X4200 M2 Replaceable Component Locations Chapter 3 Maintaining the Netra X4200 M2 Server 27 Starting the Maintenance Procedures Use the preparatory procedures in this section when you are referred to them from the removal and replacement procedures Powering Off the Server Choose one of the following methods for shutting down the server from main power mode to standby power mode See FIGURE 3 2 Graceful shutdown Use a ballpoint pen or other stylus to press and release the recessed Power button on the front panel This causes Advanced Configuration and Power Interface ACPI enabled operating systems to perform an orderly shutdown of the operating system Servers not running ACPI enabled operating systems will shut down to standby power mode immediately a Emergency shutdown Press and hold the Power button for
33. instructed to do so in a procedure developed by Sun Microsystems 1 Use SSH to log into the sunservice account The default password is changeme ssh lt SP IP address gt 1 sunservice lt SP IP Address gt s password changeme 2 At the prompt enter the servicetool command with options The options are defined in the table below Chapter 3 Maintaining the Netra X4200 M2 Server 117 118 servicetool fru_update mainboard lt Other Options gt lt value gt Other Options Value board_replaced BOARD Update FRU information for BOARD after board has been replaced fru_product_part_number Write a new part number to the FRU fru_product_serial_number Write a new serial number to the FRU fru_chassis_serial_number Write a new chassis serial number to the FRU fru_asset_tag Write a new asset tag to the FRU 3 Watch the output from the command and respond to the confirmation prompts to continue the update and to reboot the server Servicetool is going to update the mainboard FRU with product and chassis information collected from the removed mainboard The following preconditions must be true for this to work The new mainboard must be installed The service processor must not have been replaced with the motherboard The service processor firmware must not have been upgraded prior to the motherboard replacement do firmware upgrades after component swaps Do you want to continue y n y Mainboard
34. motherboard remove the server from the rack 4 Remove the cover from the server See Removing the Top Cover on page 33 5 Install the shorting jumper across the J12 header pins See FIGURE 2 6 for the J12 jumper location The function of the J12 jumper is to clear the ILOM Service Processor SP password 6 Reinstall the cover to the server 7 Reconnect AC or DC power cords to the server The server powers up to standby power mode indicated when the Power OK LED on the front panel is flashing Netra X4200 M2 Server Service Manual May 2007 8 Return the server to main power mode by using a ballpoint pen or other stylus to press and release the recessed Power button on the front panel Note You must allow the entire server not just the SP to reboot to main power mode to complete the password reset This is because the state of the J12 jumper cannot be determined without the host CPU running Wait until the end of POST when you see the CMOS password cleared by jumper message after which both the BIOS and SP passwords are reset a The ILOM SP password is reset to the default changeme a The BIOS password is also reset by a separate operation performed by the BIOS when it discovers the presence of the J12 jumper The BIOS password is not reset to changeme it is removed so that there is no longer a BIOS password set If you had a BIOS password set you are no longer prompted for one 9 Log in to the
35. or previous device KEKEKKKKKKKKKKKKKEKKKKKKKKEKK KEKE LSI Logic MPT Setup Utility Device Properties SAS1064 KREKKKKKKKK KKK KKK KKEK KKK KKK KEK KKK KR KK KKKKKKRKKKKKKKEKE v6 02 00 00 2005 07 08 x 170 Netra X4200 M2 Server Service Manual May 2007 is Device Identifier SEAGATE ST936701LSUN36G 0456 X Scan Order 2 Device Information SAS SAS Address 5000C500 001047c9 h Serial Number 39000SZC 3LC Verify Esc Exit F1 Help Alt M More Keys Alt N Next Device Alt P Previous Device Enter Select Item x KEK KKK KKK KKK KKK KKK KKK KK KKK KKK KKK KKK KKK KKK KEK KKK KKK KKK KKK KEK KKK KKK KKK KK KKK KKK KKEKEEK FIGURE E 9 Device Properties Screen TABLEE 6 Device Properties Screen Field Descriptions Field Description Device Identifier The ASCII device identifier string extracted from the device s inquiry data Scan Order The scan order for this device This is the equivalent of a SCSI ID in parallel SCSI Device Information Indicates whether the device is SAS or SATA SAS Address The SAS address of this device Serial Number The serial number of this device Verify Press Enter to access the Verify All Sectors screen From this screen you can start a verification of all sectors on the device see Device Verify Screen on page 172 If needed you can reassign defective Logical Block Addresses
36. primary disk may be migrated ia Create IS Volume Create Integrated Striping array of ia 2 to 8 disks x Es ALL DATA on array disks will be DELETED Esc Exit Menu F1 Shift 1 Help Enter Choose array type to create Esc Return to Adapter Properties kkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkk FIGURE E 14 Select New Array Type Screen Create New Array Screen The Create New Array screen allows you to select disks for a new array FIGURE E 15 shows this screen TABLE E 11 describes the fields of the screen For an IM volume when the first disk is added you are asked about the data on the disks You have two options m Press M to keep the existing data and migrate to an IM array Disk synchronization will occur m Press D to overwrite existing data and create a new IM array All data on all disks in the array will be deleted No synchronization occurs Appendix E Serial Attached SCSI BIOS Configuration Utility 183 After the volume is configured press C to create the array You are asked to save changes which will create the array After the array is created the utility returns you to the Adapter Properties screen KREKEKKKKKKKKKKKKK KK KKK KKK KKK KK KKK KKK KK KKK KKK KKK KK KKK KEK KK KK KKK KK KK KKKKEKKKKKKKKKKKK LSI Logic MPT Setup Utility v6 02 00 00 2005 07 08 Create New Array SAS1064 i s Array Type IM i Array
37. replaced power supply and the Service Required LEDs are not lit Replacing the Power Distribution Board Removing the Power Distribution Board 1 Prepare the server for power board removal See Powering Off the Server on page 28 Disconnecting Cables From the Server on page 29 Removing the Server From the Rack on page 30 Performing Antistatic Measures on page 31 Removing the Top Cover on page 33 Opening the Front Bezel on page 33 Removing the PCI Tray and PCI E Ribbon Cables on page 34 98 Netra X4200 M2 Server Service Manual May 2007 2 Remove the power supplies the optical media drive the hard drives and the mass storage assembly See a Removing a Power Supply on page 96 a Removing the DVD Drive on page 40 a Removing a Hard Drive on page 43 a Removing the Mass Storage Assembly on page 49 Remove the five screws and two bus bar screws that secure the power board to the chassis FIGURE 3 73 Bus b us bar screws 5 7 Q 7 gt l a FIGURE 3 73 Removing the Power Board Screws 4 Lift the power board out of the chassis and set it aside on an antistatic mat FIGURE 3 74 Chapter 3 Maintaining the Netra X4200 M2 Server 99 FIGURE 3 74 Lifting the Power Board From the Chassis 5 Continue to Installing the Power Distribution Board on page 100 Note Do not move the two pin jumper on the power distribution board fro
38. the fan assembly as part of another procedure return to that procedure a Otherwise continue to Installing the System Fan Assembly on page 55 Installing the System Fan Assembly 1 Remove the replacement fan assembly from its packaging and place the assembly on an antistatic mat 2 Insert your forefinger and thumb into the holes at the top of the fan assembly squeeze your fingers together and lower the fan assembly into the chassis FIGURE 3 32 Chapter 3 Maintaining the Netra X4200 M2 Server 55 FIGURE 3 32 Lowering the Fan Assembly Into the Chassis 3 Reconnect the system fan assembly cable to connector J3 on the power board FIGURE 3 33 Note The connector is not easy to see because it is positioned under the flex circuit FIGURE 3 25 shows the flex circuit connection location 56 Netra X4200 M2 Server Service Manual May 2007 FIGURE 3 33 Connecting the Fan Assembly Cable 4 5 Route the fan assembly cable back into the cable guides Consider your next step If you installed the fan assembly as part of another procedure return to that procedure Otherwise perform the following tasks to bring the server back online Installing the Top Cover on page 112 Removing Antistatic Measures on page 113 Installing the Server Chassis in the Rack on page 114 Reconnecting Cables to the Server on page 115 Powering On the Server on page 116 Chapter 3 Maintaining
39. to view additional information about the devices see FIGURE E 5 through FIGURE E 8 Descriptions of the fields are given in TABLE E 5 The SAS Topology screen shows the following objects and their significant properties a Adapter PHYs a m Attached Devices m Expanders Enclosures KREKKKKKK KEKE KKK KKK KR KKK KKK KEK KKK KKK KKK KKK KKK KKK KKK KKK KEK KKK KKK KEK KKK KKKKEKKKKKKKKKKKKKK FIGURE E 4 SAS Topology Screen Appendix E Serial Attached SCSI BIOS Configuration Utility LSI Logic MPT Setup Utility v6 02 00 00 2005 07 08 SAS Topology SAS1064 Device Identifier Discovery Device SAS1064 02 03 00 Status Info PHY 0 Good PHY 1 Good PHY 2 SEAGATE ST936701LSUN36G 0456 Good SAS PHY 3 SEAGATE ST973401LSUN72G 0356 Good SAS Esc Exit F1 Help Alt M More Keys Alt D Device Properties Alt E Expander Properties kkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkk 167 To expand the SAS Topology display select an expander or enclosure and press Enter to display all its PHYs devices bays To collapse the display press Enter again While the cursor is on the Device Identifier you can perform these actions m Press Alt E to access a specific Expander Properties screen or press Alt D to access a specific Device Properties screen m Press Enter while on an expander or enclosure to expand or collapse the display m
40. update a modifiable field to its next relative value The Esc key aborts the current context operation and or exits the current screen The user is asked to confirm if changes have been made Executable items are indicated by highlighted text and a different background color Press Enter to execute the item s associated function Throughout the user interface selections that are not currently permissible are grayed out The behavior of executable items varies throughout the Configuration Utility Adapter List Screen When you start the Fusion MPT SAS BIOS Configuration Utility the Adapter List screen appears as shown in FIGURE E 1 This screen displays a scrolling list of up to 256 LSI Logic SAS host adapters in the system and information about each of them TABLE E 2 describes the fields in this screen 160 Netra X4200 M2 Server Service Manual May 2007 Use the arrow keys to select an adapter then press Enter to view and modify the selected adapter s properties and to access the other screens After you select an adapter and press Enter the adapter s devices are scanned and the Adapter Properties screen appears See FIGURE E 3 To change the Adapter boot order use the Insert and Delete keys while on the Boot Order field Press Insert or Delete to add or remove an adapter to or from the boot order Press the and keys to modify an adapter s position in the boot order If you make changes to the boot orde
41. 17 5245 10 TMNL SOFTWARE LICENSE AGREEMNT 819 0764 10 DCT ENTITLEMENT DOC HDW S10 819 1755 10 CARD GSG NETRA_X4200 M2_SERVER ACT 820 1052 01 Chapter 1 Introduction to the Netra X4200 M2 Server 9 10 Netra X4200 M2 Server Service Manual May 2007 CHAPTER 2 Powering On and Configuring BIOS Settings This chapter contains the following procedures and information Powering On the Server on page 12 Powering Off the Server on page 14 Configuring BIOS Settings on page 15 Resetting ILOM and BIOS Passwords on page 20 Using the Clear CMOS Jumper on page 22 Using the Reset and NMI Switches on page 23 Updating the BIOS on page 24 12 Powering On the Server Note Before powering on your server for the first time follow the installation and cabling instructions provided in the Netra X4200 M2 Server Setup Guide which is online at the URL described in Related Documentation on page xii Caution Do not operate the server without all fans component heatsinks air baffles and covers installed Severe damage to server components can occur if the server is operated without adequate cooling mechanisms 1 Verify that input AC DC power cords have been connected to the server s power supplies and that standby power is on In standby power mode the Power OK LED on the front panel flashes indicating that the service processor is working and the system is ready to
42. 6 Netra X4200 M2 Server Service Manual May 2007 APPENDIX E Serial Attached SCSI BIOS Configuration Utility This appendix explains how to use the LSI Logic Fusion MPT Serial Attached SCSI SAS BIOS Configuration Utility This appendix contains the following sections a Fusion MPT SAS BIOS Overview on page 157 a Starting the SAS BIOS Configuration Utility on page 158 Configuration Utility Screens on page 159 m Performing RAID Configuration Tasks on page 195 Fusion MPT SAS BIOS Overview The Fusion MPT SAS BIOS features include m Configuration for up to 256 adapters any four can be chosen for INT13 bootrom support m Support for Message Passing Technology MPT m Support for LSI53C1064 devices m Support for SAS devices Note At this time the Netra X4200 M2 servers are shipped with support for the SAS1064 controller only SATA devices are not supported in these servers at this time Support for Integrated RAID initialization with proper firmware 157 The SAS BIOS is the bootable ROM code that manages SAS hardware resources It is specific to a family of LSI Logic Fusion MPT SAS controllers or processors The Fusion MPT SAS BIOS integrates with a standard system BIOS extending the standard disk service routine provided through INT13h During the boot time initialization the SAS BIOS determines whether the system BIOS has already installed other hard disks such as an IDE driv
43. Board 98 Removing the Power Distribution Board 98 Installing the Power Distribution Board 100 Replacing the Alarm Board 103 Removing the Alarm Board 103 Installing the Alarm Board 104 Finishing the Maintenance Procedures 107 Installing the PCI Tray 108 Installing the Top Cover 112 Closing the Front Bezel 113 Removing Antistatic Measures 113 Installing the Server Chassis in the Rack 114 Reconnecting Cables to the Server 115 Powering On the Server 116 Servicetool FRU Update Procedure 117 System Specifications 119 Netra X4200 M2 Server Service Manual May 2007 Netra X4200 M2 Specifications 119 BIOS POST Codes 121 Power On Self Test POST 121 Redirecting Console Output 121 Changing POST Options 122 POST Codes 124 POST Code Checkpoints 126 Status Indicator LEDs 131 External Status Indicator LEDs 131 Using LEDs to Identify the State of Devices 133 Front and Rear Panel LEDs 133 Hard Drive LEDs 135 Power Supply LEDs 135 Ethernet Port LEDs 136 Internal Status Indicator LEDs 136 Connector Pinouts 139 USB Connector 139 Serial Connector 140 10 100BASE T Connector 141 10 100 1000BASE T Connector 142 VGA Video Connector 143 Alarm Port 144 Serial Attached SCSI Connector 144 Flex Cable Motherboard Connector 147 Motherboard Bus Bar Power Connector 150 Front I O Interconnect Cable Connector 151 Power Supply Connector 153 Contents vii Fan Module Connector 154 D Serial Attached SCSI BIOS Configuration Utility 157 Fu
44. Connector The RJ 45 10 100BASE T Net Management connector pins and their corresponding descriptions are shown in the figure and table in this section FIGURE D 3 10 100BASE T Connector TABLE D 3 10 100BASE T Connector Pinouts Pin Number Pin Name Description 1 TX TX RX NC NC RX NC NC o N A a A Q N Positive side of transmit data Negative side of transmit data Positive side of receive data No connect No connect Negative side of receive data No connect No connect Appendix D Connector Pinouts 141 10 100 1000BASE T Connector The RJ 45 10 100 1000BASE T connector pins and their corresponding descriptions are shown in the figure and table in this section FIGURE D 4 10 100 1000BASE T Connector TABLE D 4 10 100 1000BASE T Connector Pinouts Pin Number Pin Name Description 1 TPO Positive side of data pair 0 2 TPO Negative side of data pair 0 3 TP1 Positive side of data pair 1 4 TP2 Positive side of data pair 2 5 TP2 Negative side of data pair 2 6 TP1 Negative side of data pair 1 7 TP3 Positive side of data pair 3 8 TP3 Negative side of data pair 3 142 Netra X4200 M2 Server Service Manual May 2007 VGA Video Connector The VGA video connector pins and their corresponding descriptions are shown in the figure and table in this section FIGURE D 5 VGA Video Connector TABLE D 5 VGA Video Connector Pinouts Pin Number Pin Name Description 1 RED R
45. Counts This operation issues a PHY Link Error Reset SAS IO Unit Control Request Message Note When you press Enter the following prompt appears Are you sure you want to reset Phy error counts Reset error counts for this Phy only Reset error counts for all Phys Cancel Integrated RAID Configuration and Management Screens Integrated RAID configuration and management involves many screens all of which are accessed by selecting RAID Properties on the Adapter Properties screen see FIGURE E 3 m If no RAID volumes are currently configured you are asked to create a RAID volume m If at least one RAID volume is currently configured you are shown the current volume s for management purposes The screens in the RAID configuration and management area are m Select New Array Type m Create New Array m View Array m Manage Array Select New Array Type Screen Select the type of array to create as shown in FIGURE E 14 The two new array type options are described in the text that appears on the screen No further explanation is needed 182 Netra X4200 M2 Server Service Manual May 2007 KREKKKKKKKKKKK KKK KK KKK KKK KKK KKK KKK KKK KKK KKK KEKE KKK KKK KEK KK KKK KEK KE KKKKKKKKKKKK KK KEKE LSI Logic MPT Setup Utility v6 02 00 00 2005 07 08 Select New Array Type SAS1064 x Create IM Volume Create Integrated Mirror Array of 2 disks plus an optional hot spare Data 7 on the
46. D disk 200 managing RAID hot spares 197 overview 157 starting Configuration Utility 158 synchronizing RAID arrays 199 viewing RAID volume properties 198 SC system controller card FRU name 8 SC BAT system controller battery FRU name 8 SCSI connector pinouts 144 Serial Attached SCSI BIOS See SAS BIOS serial attached SCSI connector pinouts 144 serial connector pinouts 140 server installing into rack 114 LEDs Fault 134 Power OK 134 removing from rack 30 Index 205 server features list 1 server locating 134 Service processor 8 setlocator command 134 shutting down the server 14 slide rail releasing 30 114 special considerations BIOS 16 specs system 119 standby power 29 state of server 134 summary of features 1 Sun Fire X4200 thermal grease application 81 Sun Fire X4200 M2 CPU replacement 76 heatsink replacement 76 SW2 NMI dump switch 23 SW3 Reset switch 23 system controller assembly 8 system fan assembly removing 54 replacing 53 system specs 119 T thermal grease application Sun Fire X4200 81 tools required 26 Top cover 33 top cover installing 112 replacing 112 Top cover removal 33 U USB 1 1 connector pinouts 139 Vv VGA video connector pinouts 143 WwW weight of server 30 206 Netra X4200 M2 Server Service Manual May 2007
47. Hot Spares Caution Possible data loss If you insert a hard disk drive HDD that has been configured with a RAID volume into a server that did not previously have its HDDs configured with RAID volumes the existing HDD s in the server will be converted to RAID volumes during automatic synchronization and any existing data on the existing HDD s in the server will be erased Before permanently removing a HDD that is part of an active RAID volume use the LSI Configuration Utility to delete the RAID volume from the HDD to avoid causing this problem The SCSI parameters including RAID volumes configuration are set up using the LSI BIOS Configuration Utility that is accessible by pressing the CTRL C keys during the boot process The LSI RAID firmware and BIOS is OS independent and you set up RAID while in MPTBIOS POST before booting to an OS The parameters are saved in both the NVRAM and the disk drives The RAID firmware needs 64 Mbytes of unused disk space at the end of each drive to store the metadata The metadata stored on the disk drives contains sufficient information to restore and reactivate the RAID volumes in case the NVRAM is lost for example when the motherboard is replaced However if removed the disk drives must first be labelled to ensure that they are placed back in the same disk bays from which they were removed when reinstalled When the system is powered on the RAID volumes are automatically activated and resyn
48. IPL device initialization 5538 PCI devices General device initialization 8600 Preparing CPU for booting to OS by copying all of the context of the BSP to all application processors present NOTE APs are left in the CLI HLT state AppendixB BIOS POST Codes 125 POST Code Checkpoints The POST code checkpoints are the largest set of checkpoints during the BIOS pre boot process TABLE B 2 describes the type of checkpoints that might occur during the POST portion of the BIOS These two digit checkpoints are the output from primary I O port 80 TABLE B 2 POST Code Checkpoints Post Code Description 03 Global initialization before the execution of actual BIOS POST Initialize BIOS Data Area BDA variables to their default values Initialize POST data variables NMI parity video for EGA and DMA controllers are disabled at this point 04 Check CMOS diagnostic byte to verify battery power and CMOS checksum is OK Verify CMOS checksum manually by reading storage area If the CMOS checksum is bad update CMOS with power on default values and clear passwords Initialize status register A Initializes data variables that are based on CMOS setup questions Initializes both the 8259 compatible PICs in the system 05 Initializes the interrupt controlling hardware generally PIC and interrupt vector table 06 Do R W test to CH 2 count reg Initialize CH 0 as system timer Install the POSTINT1Ch handler Enable IRQ 0 in PIC for system ti
49. Installing Top Cover 3 Remove the antistatic precautions See Removing Antistatic Measures on page 113 112 Netra X4200 M2 Server Service Manual May 2007 Closing the Front Bezel 1 To close the bezel push it up until it clicks securely in place FIGURE 3 87 Closing the Front Bezel Removing Antistatic Measures 1 Remove any antistatic straps or conductors from the server chassis 2 Remove the antistatic wrist strap from yourself Note You will be handling the chassis which is metal so the wriststrap is no longer necessary Additionally this gives you more freedom of movement for installing the server into the rack 3 Lift the server from the antistatic mat and reinstall it into the rack See Installing the Server Chassis in the Rack on page 114 Caution The server weighs approximately 40 Ib 18 kg Two people are required to carry the chassis and install it in the rack Chapter 3 Maintaining the Netra X4200 M2 Server 113 Installing the Server Chassis in the Rack 1 On the rack ensure that the rails are extended 2 Place the ends of the chassis mounting brackets into the slide rails FIGURE 3 88 Returning the Server to the Rack 3 Slide the server into the rack until the brackets lock into place 4 Release the slide rails from the fully extended position by pushing the release levers on the side of each rail FIGURE 3 89 114 Netra X4200 M2 Server
50. Installing the System Fan Assembly on page 55 7 Install the DIMM CPU duct See Installing the DIMM CPU Duct on page 69 8 Perform the following tasks to bring the server back online Installing the Top Cover on page 126 Removing Antistatic Measures on page 127 Reinstalling the Server Chassis in the Rack on page 127 Reconnecting Cables to the Server on page 130 Powering On the Server on page 131 Chapter 3 Maintaining the Netra X4200 M2 Server 65 A Replacing the GRASP Board Follow these steps to remove and replace the Graphics Redirect and Service Processor GRASP board 1 Prepare the server for GRASP board removal a Powering Off the Server on page 28 a Disconnecting Cables From the Server on page 29 a Removing the Server From the Rack on page 30 m Performing Antistatic Measures on page 31 a Removing the Top Cover on page 33 a Removing the PCI Tray and PCI E Ribbon Cables on page 34 a Removing the PCI E Cable Hold Down Bracket on page 36 Removing the GRASP Board 1 Power off the server as described in Powering Off the Server on page 28 Note Remove AC DC power supply unit inlet cables and attach a wrist strap to the button snap grounding post inside the chassis just behind the mass storage assembly see FIGURE 3 10 for the location 2 If the server is in a rack slide it far enough from the rack so that you can remove
51. L 73 SAS_DISK2_RX_P 74 DISKO_ACT_LED_L Flex Cable Motherboard Connector Pinouts Continued Appendix D Connector Pinouts 149 TABLE D 8 Flex Cable Motherboard Connector Pinouts Continued Pin Number Signal Name 75 GND 76 SPINDLE_ID1 77 SAS_DISKO_RX_N 78 GND 79 SAS_DISKO_RX_P 80 PS_KILL Motherboard Bus Bar Power Connector Main power is delivered to the motherboard through a bus bar There are two pads on the underside of the motherboard that connect 12 V and ground The pads have been designed to handle 50 A The motherboard bus bar connector pads and their corresponding descriptions are shown in the figure and table in this section 150 Netra X4200 M2 Server Service Manual May 2007 Back panel of server Motherboard Pad 1 Pad 2 FIGURE D 9 Motherboard Bus Bar Connector TABLE D 9 Motherboard Bus Bar Connector Pinouts Pad Number Pad Name Description 1 12V 12 V DC power to motherboard 2 GND Ground Front I O Interconnect Cable Connector The connection from the motherboard to the front I O board is made through a short interconnect ribbon cable On each board there is a connector Samtec STMM 113 02 S D The interconnect cable connector pins and their corresponding descriptions are shown in the figure and table in this section Appendix D Connector Pinouts 151 FIGURE D 10 Front I O Interconnect Cable Connector TABLE D 10 Front I O Interconnect Cable Connector Pinouts
52. Press Enter while on a device to activate the Locate LED At any time while on the screen press C to clear Device Mappings for non present devices Scroll the cursor to the right to display further information see FIGURE E 5 through FIGURE E 8 KEKEKKKKKKKEKKK KKK KKK KK KKK KKK KK KKK KEK KKK KKK KEK KEK KKK KR KKK KKK KR KK KKKKKKRKKEKKKKKKKKKKKK SAS Topology SAS1064 Device Identifier Negotiated Link SAS1064 02 03 00 Speed Gbps k PHY O0 Unknown PHY T Unknown ij PHY 2 SEAGATE ST936701LSUN36G 0456 3 0 PHY 3 SEAGATE ST973401LSUN72G 0356 3 0 g Esc Exit F1 Help Alt M More Keys Alt D Device Properties Alt E Expander Properties kkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkk FIGURE E 5 SAS Topology Screen 2 Negotiated Link Speed 168 Netra X4200 M2 Server Service Manual May 2007 KREKKKKKKKKKKKKKK KKK KK KKK KKK KK KKK KKK KKK KKK KKK KKK KKK KKK KKKK KEKE KKKKKKKKEKKKKKKKKKKKK FIGURE E 6 SAS Topology Screen 3 Maximum Link Speed k k PHY 0 PHY 1 PHY 2 PHY 3 Esc Exit k SAS Topology SAS1064 Device Identifier SAS1064 02 03 00 n EAGAT z n F1l Help Alt M More Keys Alt E Expander Properties Alt D Device Properties KEKE KKK KEKE KKK KEK KKK KKK KEK KKK KKK KKK KKK KK KEK KKK KEK KKK KKK KKK KEKE KKK KKK KKK KKK KKK KKK KEKE KEKEKE M
53. Sequential Access LUN 0 Only Scan only LUN 0 All Scan all LUNs 178 Netra X4200 M2 Server Service Manual May 2007 TABLE E 9 Advanced Device Properties Screen Field Descriptions Continued Field Description LUNs to Scan for Other Devices Removable Media Support Restore Defaults Controls LUN scans for all devices other than the following e SCSI Device Type 00h Direct Access e SCSI Device Type 01h Sequential Access e SCSI Device Type 04h Write Once e SCSI Device Type 05h CD ROM e SCSI Device Type 07h Optical e SCSI Device Type OEh Simplified Direct Access LUN 0 Only Scan only LUN 0 All Scan all LUNs e None Install no INT 13H interface for any Direct Access removable media devices e Boot Device Only Install INT 13H interface for a Direct Access removable media device if and only if media is present in the device at the time of BIOS initialization and either BBS System The device is selected as the boot device Refer to the BIOS Boot Specification for a description of BBS e Non BBS System The device is set up as the boot device The adapter to which the device is connected is specified as the first adapter i e 0 in the Boot Adapter List The device is specified as the first device in the adapter s device scan order list e With Media Installed Install INT 13H interfaces for Direct Access Removable Media devices if media is present in the device at the time of BIOS i
54. Service Manual May 2007 TABLE E 2 Adapter List Screen Field Descriptions Continued Field Description FW Revision The Fusion MPT firmware version and type IR or IT Status Status indicates whether an adapter is eligible for LSI Logic software control or whether it is reserved for control by non LSI Logic software Enabled The BIOS is either currently controlling the adapter or will attempt to control the adapter upon reload e Disabled The BIOS is either not controlling the adapter or will discontinue control of the adapter upon reload Whether Enabled or Disabled the user can still view and modify settings for the adapter The Boot Support setting in the Adapter Properties menu can be used to change the status of this setting The BIOS must be reloaded the system must be rebooted in order for a new Boot Support setting to take effect Error The BIOS encountered a problem with the adapter Adapter settings can be viewed and modified but the available information and functionality may be limited Boot Order The order in which adapters will boot when the system has more than one adapter Up to four of the total adapters in a system may be selected as bootable To add an adapter to the boot list press Insert while on the Boot Order field To remove an adapter from the boot list press Delete while on the desired adapter s Boot Order field Press the or keys to change the adapter s position in the boot order
55. Service Manual May 2007 FIGURE 3 89 Release Levers 5 While pushing on the release levers slowly push the server into the rack Ensure that the cables are not in the way 6 Reconnect the cables to the back of the server See Reconnecting Cables to the Server on page 115 Reconnecting Cables to the Server 1 Reconnect the following cables as appropriate GBE 1 GBE 0 GBE 3 GBE 2 USB 0 USB 1 Chapter 3 Maintaining the Netra X4200 M2 Server 115 116 NET MGT SER MGT TTYA PCI E 0 Alarm PCI X 2 PCI X 1 PCI X 0 Power supply 1 Power supply 0 2 If necessary reinstall the appropriate cables into the CMA 3 Power on the server See Powering On the Server on page 116 Powering On the Server As soon as the power cords are connected standby power is applied and depending on the configuration of the firmware the system might boot If not follow this procedure Use one of these steps to power on the server Netra X4200 M2 Server Service Manual May 2007 m Use the tip of a pen or other stylus to press the Power button on the bezel FIGURE 3 90 Power button FIGURE 3 90 Powering On the Server a Alternatively issue the poweron command to the service processor console For example start SYS Servicetool FRU Update Procedure Caution The sunservice account is for the use of Sun service representatives only Do not use the sunservice account unless you are
56. System Fan Assembly Caution Netra X4200 M2 fans are not hot swappable you must power off the server before replacing Do not operate the server without fans Note This fan assembly is also referred to as Fan Tray 0 Chapter 3 Maintaining the Netra X4200 M2 Server 53 Removing the System Fan Assembly 1 Prepare the server for fan assembly removal See a Powering Off the Server on page 28 a Disconnecting Cables From the Server on page 29 a Removing the Server From the Rack on page 30 a Performing Antistatic Measures on page 31 a Removing the Top Cover on page 33 2 Undo the thumbscrew at location J2 and slide the PCI tray back to the fully open position 3 Reach down behind the flex circuit 4 Disconnect the fan assembly cable at connector J3 on the power board by depressing the connector retention latch while pulling the connector housing straight up FIGURE 3 30 SN I FIGURE 3 30 Disconnecting the System Fan Assembly Cable 5 Remove the fan assembly cable from the cable guides 6 Insert your forefinger and thumb into the holes at the top of the fan assembly squeeze your fingers together and lift the fan assembly from the chassis FIGURE 3 31 54 Netra X4200 M2 Server Service Manual May 2007 FIGURE 3 31 Lifting the System Fan Assembly From the Chassis 7 Set the fan assembly aside on an antistatic mat 8 Consider your next step a If you removed
57. T Code Checkpoints Continued Post Code Description 13 Initialize PM regs and PM PCI regs at Early POST Initialize multi host bridge if system supports it Setup ECC options before memory clearing REDIRECTION causes corrected data to written to RAM immediately CHIPKILL provides 4 bit error det corr of x4 type memory Enable PCI X clock lines in the 8131 20 Relocate all the CPUs to a unique SMBASE address The BSP will be set to have its entry point at A000 0 If less than 5 CPU sockets are present on a board subsequent CPUs entry points will be separated by 8000h bytes If more than 4 CPU sockets are present entry points are separated by 200h bytes CPU module will be responsible for the relocation of the CPU to correct address NOTE APs are left in the INIT state 24 Decompress and initialize any platform specific BIOS modules 30 Initialize System Management Interrupt 2A Initializes different devices through DIM 2C Initializes different devices Detects and initializes the video adapter installed in the system that have optional ROMs 2E Initializes all the output devices 31 Allocate memory for ADM module and decompress it Give control to ADM module for initialization Initialize language and font modules for ADM Activate ADM module 33 Initializes the silent boot module Set the window for displaying text information 37 Displaying sign on message CPU information setup key message and any OEM specific information 38 Initi
58. Tray 1 Reconnect the following PCI E cable goldfinger assembly at the following connectors on the motherboard assembly FIGURE 3 82 PCI EOx8 J2 m PCI E1x8 J18 m PCI E3x8 J21 PCI E0 J2 PCI E1 J18 m J m m PCI E3 J21 FIGURE 3 82 Reconnecting the PCI E Cables Goldfinger Assembly 2 Reconnect the PCI E cable cover and tighten the three captive screws that hold it in position FIGURE 3 83 108 Netra X4200 M2 Server Service Manual May 2007 FIGURE 3 83 Reconnecting the PCI E Cable Cover 3 Lower the PCI tray and slide it forward FIGURE 3 84 Chapter 3 Maintaining the Netra X4200 M2 Server 109 FIGURE 3 84 Lowering the PCI Tray 4 Tighten the thumbscrew and reconnect the cable at J2 FIGURE 3 85 5 Reconnect PCI E cables from the motherboard into connectors J6 J7 and J1 on the front edge of the PCI tray Wiggle the connections to ensure they are latched and fully seated FIGURE 3 85 110 Netra X4200 M2 Server Service Manual May 2007 FIGURE 3 85 Reconnecting J2 and Tightening the Thumbscrew 6 Install the top cover See Installing the Top Cover on page 112 Chapter 3 Maintaining the Netra X4200 M2 Server 111 Installing the Top Cover 1 Place the top cover on the chassis Set the cover down so that it hangs over the rear of the server by about an inch 25 mm 2 Slide the cover forward until it latches into place FIGURE 3 86 FIGURE 3 86
59. X4200 M2 38 Bezel 7 bezel 33 113 LEDs Activity 134 Fault 134 Locator 134 BIOS Boot specification for SAS 158 changing menu settings 15 configuring 15 menu tree 19 Option ROM size 18 overview 15 PCI X slot priority 16 POST code checkpoints 126 POST codes 124 POST options 122 POST overview 121 redirecting console output for POST 121 SAS RAID 157 setup screens summary 18 special considerations 16 updating 24 button Locator 134 Power on off 134 Cc Cable Hold Down Bracket removing 36 cable kit 9 Clear CMOS jumper 22 comments and suggestions xiii component overview figure 201 Netra X4200 M2 5 Configuration Utility screens for SAS BIOS 159 configurations for DIMMs 73 configuring BIOS 15 connector pinouts 10 100 1000BASE T 142 10 100BASE T 141 Ethernet 10 100 141 Ethernet 10 100 1000 142 fan module 154 flex cable motherboard 147 front I O interconnect cable 151 motherboard bus bar power 150 power supply 153 serial 140 serial attached SCSI 144 USB 1 1 139 VGA video 143 console output redirecting 121 CPU fault LED 137 Sun Fire X4200 M2 76 D DIMM Population Rules 72 DIMM replacement 71 DIMM CPU duct installing 69 removing 68 replacing 68 DIMMs 8 71 fault LEDs 137 installing 74 supported configurations 73 disk drives see hard drive documentation related xii driver updates xi DVD optical media drive FRU name 7 DVD dr
60. a X4200 M2 Server Service Manual May 2007 Replacing the Alarm Board Removing the Alarm Board 1 Prepare the server for alarm board removal See Powering Off the Server on page 28 Disconnecting Cables From the Server on page 29 Removing the Server From the Rack on page 30 Performing Antistatic Measures on page 31 Removing the Top Cover on page 33 Removing the PCI Tray and PCI E Ribbon Cables on page 34 2 Disconnect all three cables from the alarm board at their connectors FIGURE 3 77 FIGURE 3 77 Disconnecting the Cables From the Alarm Board 3 Push down on the green tab pivot the alarm board inward and lift the alarm board out of the chassis FIGURE 3 78 Chapter 3 Maintaining the Netra X4200 M2 Server 103 FIGURE 3 78 Lifting the Alarm Board Out of the Chassis 4 Set the alarm board aside on an antistatic mat 5 Consider your next step a If you removed the alarm board as part of another procedure return to that procedure m Otherwise continue to Installing the Alarm Board on page 104 Installing the Alarm Board 1 Remove the replacement alarm board from its packaging and place the board on an antistatic mat 2 Align the tabs of the alarm board with the slots in the chassis wall FIGURE 3 79 104 Netra X4200 M2 Server Service Manual May 2007 FIGURE 3 79 Aligning the Alarm Board With Chassis Wall 3 Swing the alarm board up to the chassis w
61. acing 82 N Netra X4200 M2 acoustic noise emission specs 120 back panel figure 4 battery replacement 38 component overview figure 5 DVD drive replacement 40 environmental specs 120 overview figure 5 power specs 119 replaceable component locations 26 Netra X4200M2 Server Power button 13 NMI dump switch SW2 23 noise emission specs Netra X4200 M2 120 O OK to Remove LED 135 operating state determining 134 Option ROM size 18 OSP board 8 P PCI Cable hold down bracket 9 204 Netra X4200 M2 Server Service Manual May 2007 PCI Ecard 9 PCI PCIE and PCIX FRU names 9 PCI tray installing 108 removing 34 PCI E and PCI X cards designations 8 PCI E card installing 94 removing 92 replacing 92 PCI X slot BIOS priority 16 PCI X card installing 90 removing 88 replacing 88 PDB power board FRU name 7 physical specifications 119 pinout alarm port 144 pinouts See connector pinouts ports alarm 144 POST changing options 122 code checkpoints 126 codes table 124 overview 121 redirecting console output 121 Power OK LED power supply 135 server 134 on off button 134 power cords disconnecting 30 reconnecting 116 distribution board 7 installing 100 removing 98 replacing 98 supply 7 hot swapping 95 installing 97 LEDs 135 Fault 96 135 Power OK 135 removing 96 replacing 95 Power button location 13 power specs Netra X4200 M2 119 power supply connector pi
62. afety guidelines in the Netra X4200 M2 Server Safety and Compliance Guide 820 0068 Product Updates For product updates that you can download for the Netra X4200 M2 server go to the following web site www sun com netra x4200 xi Related Documentation For a description of the document set for the Netra X4200 M2 server see the Netra X4200 M2 Server Getting Started Guide that is packed with your system and also posted at the product s documentation web site See the following URL then navigate to your product http www sun com documentation Translated versions of some of the product documents are available at the documentation web site English documentation is revised more frequently and might be more up to date than the translated documentation For all Sun hardware documentation see the following URL http www sun com documentation For Solaris and other software documentation see the following URL http docs sun com xii Using UNIX Commands This document might not contain information about basic UNIX commands and procedures such as shutting down the system booting the system and configuring devices Refer to the following for this information a Software documentation that you received with your system m Solaris Operating System documentation which may be found at http docs sun com Netra X4200 M2 Server Service Manual May 2007 Typographic Conventions Typeface Mean
63. aintaining the PCI The PCI tray is a carrier for the PCI X and PCI Tray Tray on page 34 PCI E cards 3 Hard drive fan Replacing the Hard Fans that provide supplemental cooling of assembly Drive Fan Assembly the hard drives and optical media drive on page 58 4 Mass storage Replacing the Mass Bays that house hard drives and optical assembly Storage Assembly on media drive page 47 5 Hard drives Replacing a Hard SFF SAS 2 5 inch form factor hard drives HDDO Drive on page 43 HDD1 HDD2 HDD3 not DVD drive Replacing the DVD DVD drive DVD pictured Drive on page 40 6 Power Replacing the Power Provides the main 12V power interconnect PDB distribution Distribution Board between the power supplies and the other board on page 98 boards 7 Bezel Opening the Front Protects and provides access to hard drives Bezel on page 33 DVD drive LEDs and power button Passive latch for earthquake 8 Air filter Cleans air before it enters system Filter media meets NEBS requirements 9 Flex circuit Replacing the Mass Two versions 2HDD and 4HDD available to cable Storage Assembly on prevent shorting page 47 10 LED board Replacing the LED Contains the push button circuitry and LEDs LEDBD Board on page 62 that are displayed on the bezel of the box 11 System Fan Replacing the System Fans for the motherboard assembly FTO FMO Assembly Fan Assembly on FTO FM1 pagesos FT0 FM2 12 Power supplies Replacing a Powe
64. alizes different devices through DIM 39 Initializes DMAC 1 and DMAC 2 3A Initialize RTC date time 3B Test for total memory installed in the system Also Check for DEL or ESC keys to limit memory test Display total memory in the system 3C By this point RAM read write test is completed program memory holes or handle any adjustments needed in RAM size with respect to NB Test if HT Module found an error in Boot Block and CPU compatibility for MP environment 40 Detect different devices Parallel ports serial ports and coprocessor in CPU etc successfully installed in the system and update the BDA EBDA etc 50 Programming the memory hole or any kind of implementation that needs an adjustment in system RAM size if needed 52 Updates CMOS memory size from memory found in memory test Allocates memory for Extended BIOS Data Area from base memory 60 Initializes NUM LOCK status and programs the KBD typematic rate 75 Initialize Int 13 and prepare for IPL detection AppendixB BIOS POST Codes 127 TABLE B 2 POST Code Checkpoints Continued Post Code Description 78 Initializes IPL devices controlled by BIOS and option ROMs 7A Initializes remaining option ROMs 7C Generate and write contents of ESCD in NVRAM 84 Log errors encountered during POST 85 Display errors to the user and gets the user response for error 87 Execute BIOS setup if needed requested 8C After all device initialization is done programmed any user se
65. all until it clicks into place FIGURE 3 80 FIGURE 3 80 Swinging the Alarm Board Into Place 4 Reconnect all three cables to the alarm board at their connectors FIGURE 3 81 Chapter 3 Maintaining the Netra X4200 M2 Server 105 106 FIGURE 3 81 Connecting the Cables to the Alarm Board 5 Route the cables into the cable guides 6 Consider your next step a If you installed the alarm board as part of another procedure return to that procedure a Otherwise perform the following tasks to bring the server back online Installing the Top Cover on page 112 Closing the Front Bezel on page 113 Removing Antistatic Measures on page 113 Installing the Server Chassis in the Rack on page 114 Reconnecting Cables to the Server on page 115 Powering On the Server on page 116 Netra X4200 M2 Server Service Manual May 2007 Finishing the Maintenance Procedures Use the procedures in this section to finish the removal and replacement procedures Tasks to perform to finish the procedures Installing the PCI Tray on page 108 Installing the Top Cover on page 112 Closing the Front Bezel on page 113 Removing Antistatic Measures on page 113 Installing the Server Chassis in the Rack on page 114 Reconnecting Cables to the Server on page 115 Powering On the Server on page 116 Chapter 3 Maintaining the Netra X4200 M2 Server 107 Installing the PCI
66. ard 104 DIMM CPU duct 69 DIMMs 74 fan assembly 55 hard drive 46 hard drive fan assembly 60 LED board 64 mass storage assembly 51 motherboard assembly 86 PCI tray 108 PCI E card 94 PCI X card 90 power distribution board 100 supply 97 server into rack 114 top cover 112 internal LEDs 136 IOBD I O board FRU name 8 J jumpers 22 Clear CMOS 22 diagram of location 22 NMI dump switch 23 Reset switch 23 SW2 23 SW3 23 L latch release button hard drive 44 LED board 7 installing 64 removing 62 replacing 62 LEDBD LED board FRU name 7 LEDs about 131 Activity bezel 134 hard drive 135 alarm 134 back panel locations 132 CPU fault 137 DIMM fault 137 Ethernet port 136 external 131 Fault hard drive 135 power supply 96 135 server 134 front panel 133 front panel locations 132 GRASP Board Power Status 137 hard drive 135 Input OK 135 internal 136 Locator 134 OK to Remove 135 Power OK power supply 135 server 134 power supply 135 limitations of Option ROM size 18 locating the server 134 Locator button 134 LED 134 Index 203 M Maintenance procedures finishing 107 starting 28 Mass Storage Assembly 7 mass storage assembly installing 51 removing 49 replacing 47 MB CPU board FRU name 8 memory 71 memory replacement 71 menu tree BIOS setup screens 19 motherboard bus bar power connector pinouts 150 motherboard assembly 8 installing 86 repl
67. as a single physical disk drive no matter how many drives they contain RAID Combination Support Possible RAID Combinations in a four HDD server are listed below Two drives RAID 0 two drives non RAID Two drives RAID 1 two drives non RAID Two drives RAID 0 two drives RAID 1 Two drives RAID 0 two drives RAID 0 Two drives RAID 1 Two drives RAID 1 Three drives RAID 0 one drive non RAID Four drives RAID 0 Two drives RAID 1 one hot spare drive one drive non RAID Four drives non RAID 194 Netra X4200 M2 Server Service Manual May 2007 Performing RAID Configuration Tasks This section contains the following information and instructions for using the Configuration Utility to set up RAID m Creating a RAID 0 Volume on page 195 Creating a RAID 1 Volume on page 196 Creating a Second RAID Volume on page 198 Viewing RAID Volume Properties on page 198 Managing Hot Spares on page 197 Synchronizing an Array on page 199 Activating an Array on page 199 Deleting an Array on page 199 Locating a Disk Drive on page 200 Note The RAID firmware needs at least 64 Mbytes of unused disk space at the end of each drive to store metadata Creating a RAID 0 Volume A RAID 0 volume also referred to as Integrated Striping IS offers the ability to stripe data across multiple hard disks This can increase storage capacity and performance by combining multiple disks int
68. ave a Hot Spare Only one Hot Spare per RAID array is permitted You can define a Hot Spare when you create an array or at any time after creation if the array is made up of two disks or fewer This field is grayed out under the following conditions e The disk does not meet the minimum requirements for use in a RAID array e The array already has a Hot Spare e The array is made up of the maximum number of disks three e The disk is not large enough to mirror existing data on the primary disk e Integrated Striping firmware is used Striped arrays do not support Hot Spares Appendix E Serial Attached SCSI BIOS Configuration Utility 185 TABLE E 11 Create New Array Screen Field Descriptions Continued Field Description Drive Status e Ok Disk is online and fully functional e Missing Disk is not responding e Failed Disk has failed e Initing Disk is initializing e CfgOffln Disk is offline at host s request e UserFail Disk is marked failed at host s request e Offline Disk is offline for some other reason e Inactive Disk has been set inactive e Not Syncd Data on disk is not synchronized with the rest of the array e Primary Disk is the primary disk for a two disk mirror and is operating properly e Secondary Disk is the secondary disk for a two disk mirror and is operating properly Wrg Type Device is not compatible for use as part of a RAID array e Too Small Disk is too small to mirror e
69. aximum Link Speed Gbps 3 0 3 0 ST936701LSUN36G 0456 3 0 EAGATE ST973401LSUN72G 0356 3 0 KEKKKKKKKKEKKKKKKKKE KKK KKK KKK KK KKK KKK KK KKK KKK KEK KKK KKK KEK K KKK KEKE KK KKKKKKEKKKKKKKKKKKK Alt D Devic Properties Alt FIGURE E 7 SAS Topology Screen 4 Target Capabilities KEKKKKKKKKEKKKKKK KEKE KKK KKK KKK KK KKK KKK KEK KKK KKK KEK KKK KEKE KKK KKK KKK KKK KKKKEKKKKKKKKEKKKK SAS Topology SAS1064 Device Identifier SAS1064 02 03 00 SEAGAT SEAGAT TE S7 TE S7 Fl Help Alt M More Keys Properties w PHY 0 PHY 1 PHY 2 PHY 3 Esc Exit Alt D Devic Alt Appendix E E Expander Properties KEKE KKK KKK KK KKK KE KKK KEK KKK KKK KEK KEK KEK KKK KKK KEK KEK KK KKK KKK KKK KKK KEK KEK KKK KEKE KKK KKK KK KEKE KE SAS Topology SAS1064 Device Identifier Target SAS1064 02 03 00 Capabilities PHY 0 PHY 1 PHY 2 SEAGATE ST936701LSUN36G 0456 SSP PHY 3 SEAGATE ST973401LSUN72G 0356 SSP K Esc Exit Fl Help Alt M More Keys Initiator Capabilities 936701LSUN36G 0456 973401LSUN72G 0356 E Expander Properties KKK KK KKK KEKE KKK KKK KKK KEK KKK KKK KEK KEK KKK KKK KEK KEK KEK KEK KEK KEK KEK KEK KEK KEK KEK KKK KEKE KKE KK KKK KEKE KEEK Serial Attached SCSI BIOS Configuration Utility 169 FIGURE E 8 SAS Topology Screen 5 Initiator Capabilities TABLEE 5 SAS Topology Screens Field
70. ayout as the Create New Array screen Appendix E Serial Attached SCSI BIOS Configuration Utility 189 If you select Synchronize Array Activate Array or Delete Array you are prompted to confirm the choice by pressing Y for yes or N for no KREKEKKKKKKKKKKKK KEK KKKKKKKEKKK KK KKK KKK KK KK KKK KKK KKK KEKE KKK KKK KK KKK KKKKKEKKKKKKKKKKKK LSI Logic MPT Setup Ut Manage Array SAS106 Identifier Type Scan Order Size MB Status Manage Hot Spare Synchronize Array Activate Array Delete Array Esc Exit Menu k k k w k k k k Enter Select Item k ility v6 02 00 00 2005 07 08 4 LSILOGICLogical Volume IM 2 69618 Optimal F1 Shift 1 Help FIGURE E 17 Manage Array Screen TABLE E 13 Manage Array Screen Field Descriptions 3000 kkkkxkkxkxkxkxkkkxkxkxkxkkkkkkxkkkkkxkxkkkkkxkxkkkkkkkkkkkkkxkkkkxkkxkkkkkkxkxkkkkkxkxkkkkkxkxkkkkkxxkx k Field Identifier Type Scan Order Size MB Status Description The identifier of the array The RAID type of the array The scan order of the array The size of the array The status of the array 190 Netra X4200 M2 Server Service Manual May 2007 TABLE E 13 Manage Array Screen Field Descriptions Continued Field Description Manage Hot Spare Synchronize Array Activate Array Delete Array Press Enter to modify the array hot spare configuration This field is grayed out unde
71. b keys Press Enter to select the field A dialog box appears The box presents you with the options available for the setup field that you have chosen Modify the setup field and close the screen To modify other setup parameters use the arrow and Tab keys to navigate to the desired screen and menu item and repeat Steps 1 through 4 Otherwise go to Step 6 Press and release the right arrow key until the Exit menu screen is displayed Follow the instructions on the Exit menu screen to save your changes and exit the BIOS Setup utility BIOS Considerations This section contains information and considerations regarding the system BIOS Peripheral Component Interconnect PCI Card Slot Booting Priority For the locations of the PCI slots see Replacing a PCI X Card on page 88 and Replacing the PCI E Card on page 92 The slots for the Netra X4200 M2 Server PCI cards are detected by the BIOS during startup in the following order T PCI X Slot 2 PCI X Slot 3 PCI X Slot 4 PCIX Slot 1 Jg fF Q N PCI E Slot 0 Netra X4200 M2 Server Service Manual May 2007 Ethernet Port NIC Device and Driver Naming These servers each have four 10 100 1000BASE T Gigabit Ethernet ports NICs The chassis labeling of the physical ports is shown in FIGURE 2 3 NET 2 NET 3 NET 0 NET 1 FIGURE 2 3 Ethernet Port Chassis Labeling Designations Note The device naming for the NICs is reported differently by
72. be fully powered on to main power mode See FIGURE 2 1 for the LED location 2 Use a ballpoint pen or other stylus to press and release the recessed Power button on the server front panel See FIGURE 2 1 for the Power button location When main power is applied to the entire server the Power OK LED next to the Power button lights and remains lit Note The ILOM Service Processor will boot immediately after AC DC power is applied The host system motherboard is held in reset mode and the BIOS code will not execute until the ILOM boot is complete FIGURE 2 1 shows the LED location on the server front panel with the bezel open Netra X4200 M2 Server Service Manual May 2007 Power OK LED Power button oo Ao Ho ae FIGURE 2 1 Server Front Panel With Bezel Open FIGURE 2 2 shows the LED location on the front panel with the bezel closed FIGURE 2 2 Server Front Panel With Bezel Closed Chapter 2 Powering On and Configuring BIOS Settings 13 Powering Off the Server Choose a method for shutting down the server from main power mode to standby power mode a Graceful shutdown Use a ballpoint pen or other stylus to press and release the Power button on the front panel This causes Advanced Configuration and Power Interface ACPI enabled operating systems to perform an orderly shutdown of the operating system Servers not running ACPI enabled operati
73. cacheability Ported to handle any OEM specific programming needed during End POST Copy OEM specific data from POST_DSEG to RUN_CSEG 128 Netra X4200 M2 Server Service Manual May 2007 TABLE B 2 POST Code Checkpoints Continued Post Code Description B1 Save system context for ACPI 00 Prepares CPU for booting to OS by copying all of the context of the BSP to all application processors present NOTE APs are left in the CLIHLT state 61 70 OEM POST Error This range is reserved for chipset vendors and system manufacturers The error associated with this value may be different from one platform to the next Appendix B BIOS POST Codes 129 130 Netra X4200 M2 Server Service Manual May 2007 APPENDIX C Status Indicator LEDs External Status Indicator LEDs The server provides the following groups of LEDs Front and Rear Panel LEDs on page 133 Hard Drive LEDs on page 135 Power Supply LEDs on page 135 Ethernet Port LEDs on page 136 These LEDs provide a quick visual check of the state of the system FIGURE C 1 and FIGURE C 2 show the locations of the external status indicator LEDs Refer to TABLE C 1 and TABLE C 2 for descriptions of the LED behavior 131 User controlled telco alarm LEDs Power button Locate button LEDs Hard disk drive status indicator LEDs FIGURE C 1 Netra X4200 Server M2 Front Panel LEDs
74. chronization is automatically performed One of the disk drives can be set up as a hot spare disk if a RAID 1 mirroring volume is already set up If one of the two disk drives used in the RAID 1 volume fails the hot spare drive automatically replaces it in the volume and resync is immediately performed It must be noted that until the resync is completed the system is vulnerable to a failure of the now primary disk the disk left from the original mirrored volume since full data redundancy is not yet achieved When the bad disk is replaced the new disk automatically becomes the new hot spare disk for the mirrored volume Appendix E Serial Attached SCSI BIOS Configuration Utility 193 RAID Level Support The following items describe the RAID level support for these servers RAID 1 mirroring is supported RAID 0 striping is supported LSI RAID 1E or IME mirroring over more than two drives is not supported RAID 0 1 and 1 0 are not supported by the SAS1064 controller RAID Volume Support The following items describe the RAID volumes supported for these servers Up to two active RAID volumes are supported per system RAID 0 RAID 1 or both A striped volume RAID 0 can contain up to four disk drives A mirrored volume RAID 1 can contain up to two disk drives One disk drive can be set up as hot spare for a RAID 1 array one hot spare disk per controller maximum Volumes are transparent to the OS and are seen
75. conds 0 999 0 no timeout that the host uses to timeout I Os for the following devices e SCSI Device Type 01h Sequential Access The time in seconds 0 999 0 no timeout that the host uses to timeout I Os for devices other than the following e SCSI Device Type 00h Direct Access e SCSI Device Type 01h Sequential Access e SCSI Device Type 04h Write Once e SCSI Device Type 05h CD ROM e SCSI Device Type 07h Optical e SCSI Device Type OEh Simplified Direct Access Appendix E Serial Attached SCSI BIOS Configuration Utility 177 TABLE E 9 Advanced Device Properties Screen Field Descriptions Continued Field Description LUNs to Scan for Block Devices LUNs to Scan for Block Devices Removable LUNs to Scan for Sequential Devices Controls LUN scans for the following devices with nonremovable media e SCSI Device Type 00h Direct Access e SCSI Device Type 04h Write Once e SCSI Device Type 07h Optical e SCSI Device Type OEh Simplified Direct Access LUN 0 Only Scan only LUN 0 All Scan all LUNs Controls LUN scans for the following devices with removable media e SCSI Device Type 00h Direct Access e SCSI Device Type 04h Write Once e SCSI Device Type 05h CD ROM e SCSI Device Type 07h Optical e SCSI Device Type OEh Simplified Direct Access LUN 0 Only Scan only LUN 0 All Scan all LUNs Controls LUN scans for the following device e SCSI Device Type 01h
76. d drive does not require removing the server from a rack Nor does the procedure require removing the top cover of the server Removing a Hard Drive 1 Press the green tabs on either side of the bezel and pull the bezel forward and down FIGURE 3 16 FIGURE 3 16 Opening the Bezel Chapter 3 Maintaining the Netra X4200 M2 Server 43 2 Identify the location of the hard drive that you want to remove FIGURE 3 17 HDD3 CETTE TTT LTES o e e e eee e oeoa Hoos TTT ol Hood noo O SSOSSHSHSSSSSSSSSHSHSHSSSSSSSSSSS m O See SOOSSeees FIGURE 3 18 HDD Locations on a 4x HDD configuration 3 Issue the OS commands required to stop using the hard drive Exact commands required depend on the configuration of your hard drives You might need to unmount file systems or perform RAID commands 4 On the drive you plan to remove push the latch release button FIGURE 3 19 to open the hard drive latch 44 Netra X4200 M2 Server Service Manual May 2007 Latch release button FIGURE 3 19 Opening the Hard Drive Latch Caution The latch is not an ejector Do not bend it too far to the left Doing so can damage the latch 5 Grasp the latch and pull the drive out of the drive slot FIGURE 3 20 FIGURE 3 20 Removing the Hard Drive From the Server Chapter 3 Maintaining the Netra X4200 M2 Server 45 6 Consider your next steps a If you are replaci
77. d drives See a Removing the DVD Drive on page 40 a Removing a Hard Drive on page 43 3 Disconnect the following cables from the mass storage assembly and power distribution board FIGURE 3 24 a System fan a Hard drive fan a PCI tray power cable Chapter 3 Maintaining the Netra X4200 M2 Server 49 a Flex circuit a Ribbon cable to power distribution board PDB 4 Move the cables as far out of the way as possible Loosen both the screw at the back of the mass storage assembly and the screw at the front of the chassis FIGURE 3 26 FIGURE 3 26 Loosening the Mass Storage Assembly Screws Note The screws are captive and cannot be completely removed 6 Slide the mass storage assembly back pivot the back end up and lift the assembly out of the chassis FIGURE 3 27 Caution As you remove the assembly be careful that the flex cable does not get caught on the flex circuit or the PDB ribbon cable 50 Netra X4200 M2 Server Service Manual May 2007 DA WS NY N By FIGURE 3 27 Lifting the Mass Storage Assembly From the Chassis 7 8 Set the mass storage assembly aside on an antistatic mat Consider your next step a If you removed the mass storage assembly as part of another procedure return to that procedure m Otherwise continue to Installing the Mass Storage Assembly on page 51 Installing the Mass Storage Assembly 1 Remove the replacement mass storag
78. d the top of the CPU Too much movement could disturb the layer of thermal grease leading to component damage 3 Carefully position and align the heatsink over the CPU Chapter 3 Maintaining the Netra X4200 M2 Server 81 Note The heatsink is not symmetrical and it must be aligned before you place it on the CPU Note that the half of the Sun Microsystems logo imprinted on the top of the heatsink will create a complete logo when correctly aligned with the adjacent heatsink 4 Lower the heatsink onto the CPU aligning the mounting bolts with their holes on the motherboard 5 Alternately tighten the four heatsink mounting screws 180 degrees at a time until each spring is completely compressed 82 Replacing the Motherboard Assembly Removing the Motherboard Assembly 1 Prepare the server for motherboard assembly removal See a Powering Off the Server on page 28 a Disconnecting Cables From the Server on page 29 a Removing the Server From the Rack on page 30 a Performing Antistatic Measures on page 31 2 Remove the following components a Top cover Removing the Top Cover on page 33 a PCI tray Removing the PCI Tray and PCI E Ribbon Cables on page 34 a Cable hold down bracket Removing the PCI E Cable Hold Down Bracket on page 36 Cables for PCI E Removing the PCI Tray and PCI E Ribbon Cables on page 34 a DIMM CPU duct Removing the DIMM CPU Duct o
79. dapter settings TABLE E 8 describes the fields of the screen The Advanced Adapter Properties screen provides access to advanced Device Properties and PHY Properties To modify the Link Error Settings Threshold Count and Threshold Time press Enter while the cursor is on the desired field and type the new value KREKKKKRKKKKEKKKKKKE KKK KK KK KEK KKK KKK KKK KKK KKK KKK KKK KKK KEK KKK KKK KR KK KK KKK KRKKKKKKKKKKKKKK LSI Logic MPT Setup Utility v6 02 00 00 2005 07 08 Advanced Adapter Properties SAS1064 x TRO OB NVM Yes i IO Port Address A800 Chip Revision ID 02 Appendix E Serial Attached SCSI BIOS Configuration Utility 173 Spinup Delay Secs CHS Mapping Link Error Settings Invalid DWORDs Loss of DWORD Sync PHY Reset Errors PHY Properties Restore Defaults Esc Exit Menu F1 Shi F F FF F F F F FF F F F F HF F HF F kkkkxkxkxkxkxkxkxkkxkkxkxkxkkxkkxkxkxkkkkxkkxk 2 SCSI Plug and Play Mapping Threshold Threshold Count Time Secs 0 0 0 0 Running Disparity Errors 0 0 0 0 Advanced Device Properties ft 1 Help Enter Select Item Change Item kkkxkxkxkxkxkxkxkxkxkkxkxkxkxkxkkkkxkkkkkkxkxkkkkkxkxkxkkkkxkxkkkkkkkkxk FIGURE E 11 Advanced Adapter Properties Screen TABLE E Advanced Adapter Properties Screen Field Descriptions Field Description IRQ The Interrupt Request Line used by the adapter The system BIOS assigns this value NVM I
80. e POST INTO09h handler gets control for IRQ1 8600 Preparing CPU for booting to OS by copying all of the context of the BSP to all application processors present NOTE APs are left in the CLI HLT state 124 Netra X4200 M2 Server Service Manual May 2007 TABLE B 1 POST Codes Continued Post Code Description de00 Preparing CPU for booting to OS by copying all of the context of the BSP to all application processors present NOTE APs are left in the CLI HLT state 8613 Initialize PM regs and PM PCI regs at Early POST Initialize multi host bridge if system supports it Setup ECC options before memory clearing Enable PCI X clock lines in the 8131 0024 Decompress and initialize any platform specific BIOS modules 862a BBS ROM initialization 002a Generic Device Initialization Manager DIM Disable all devices 042a ISA PnP devices Disable all devices 052a PCI devices Disable all devices 122a ISA devices Static device initialization 152a PCI devices Static device initialization 252a PCI devices Output device initialization 202c Initializing different devices Detecting and initializing the video adapter installed in the system that have optional ROMs 002e Initializing all the output devices 0033 Initializing the silent boot module Set the window for displaying text information 0037 Displaying sign on message CPU information setup key message and any OEM specific information 4538 PCI devices
81. e If such drives are already installed the SAS BIOS maps any SAS drives it finds behind these drives Otherwise the SAS BIOS installs drives starting with the system boot drive In this case the system boots from a drive controlled by the SAS BIOS The LSI Logic SAS BIOS supports the BIOS Boot Specification BBS Boot Initialization With BIOS Boot Specification BBS The Fusion MPT SAS BIOS supports the BIOS Boot Specification BBS which allows you to choose which device to boot from by selecting the priority To use this feature the system BIOS must also be compatible with the BBS If the system supports the BBS you can use the system BIOS Setup menu to select the boot order and drive order In the system BIOS Setup the Boot Connection Devices menu lists the available boot options Use that menu to select the device and rearrange the order Then exit to continue the boot process Starting the SAS BIOS Configuration Utility If you have SAS BIOS version 6 xx and it includes the Fusion MPT SAS BIOS Configuration Utility you can change the default configuration of the SAS host adapters You may decide to change these default values if there is a conflict between device settings or if you need to optimize system performance The version number of the SAS BIOS appears in a banner displayed on the computer monitor during bootup If the utility is available this message also appears during bootup Press Ctrl C to start LSI Logic C
82. e 66 remote management of the server Service Processor also known as Service Processor 18 Alarm board Replacing the Alarm Provides dry contact switching according to Board on page 103 alarm conditions 19 PCI X cards Replacing a PCI X Optional add on cards PCIX1 Card on page 88 PCIX2 PCIX3 8 Netra X4200 M2 Server Service Manual May 2007 TABLE 1 2 Netra X4200 M2 Server FRU List Continued Item No FRU Replacement Instructions Description FRU Name Cable Removing the PCI kit Goldfinger Tray and PCI E Ribbon Cables on page 34 20 PCI E card Replacing the PCI E Card on page 92 21 PCI E cable Removing the PCI E hold down Cable Hold Down bracket Bracket on page 36 PCI E ribbon cables that connect the motherboard to the PCI tray Optional add on cards PCIEO The FRU name is used in system messages Accessory Kit TABLE 1 3 lists the contents of the accessory kit that is shipped with the Netra X4200 M2 servers TABLE 1 3 Netra X4200 M2 Accessory Kit Item Part Number WRIST STRAP 10MM STUDS 250 1691 01 M5 NUT KIT ENXU 370 6066 01 RTE 23 19 07 88 02 00 SW NGA K ACT 401 4137 01 Netra X4200 M2 Server Getting Started Guide printed sheet 820 1052 10 Serial to RJ45 cable adapter DB9S to RJ45F 530 3100 01 WAGO ASSEMBLY KIT 565 1882 01 TMNL SMI BINARY CODE LICENSE 816 4835 10 SUN GENERIC SAFETY DOC 816 7190 10 MNL DCT SUN INSTALL CHECK TOOL 817 0440 12 SUPP LIC TERMS SA 8
83. e The disk is not large enough to mirror existing data on the primary drive e This disk has been selected as the Hot Spare for the RAID array Hot Spr Specifies whether the disk is the Hot Spare for a RAID array Yes or No RAID Arrays are not required to have a Hot Spare Only one Hot Spare per RAID array is permitted You can define a Hot Spare when you create an array or at any time after creation if the array is made up of two disks or fewer This field is grayed out under the following conditions e The disk does not meet the minimum requirements for use in a RAID array e The array already has a Hot Spare e The array is made up of the maximum number of disks three e The disk is not large enough to mirror existing data on the primary disk Integrated Striping firmware is used Striped arrays do not support Hot Spares 188 Netra X4200 M2 Server Service Manual May 2007 TABLE E 12 View Array Screen Field Descriptions Continued Field Description Drive Status e Ok Disk is online and fully functional e Missing Disk is not responding e Failed Disk has failed e Initing Disk is initializing e CfgOffln Disk is offline at host s request e UserFail Disk is marked failed at host s request e Offline Disk is offline for some other reason e Inactive Disk has been set inactive e Not Syncd Data on disk is not synchronized with the rest of the array e Primary Disk is the primary disk for a
84. e and cannot be completely removed from the PCI tray 3 Slide the PCI E card to the left and lift it out of the PCI tray FIGURE 3 68 L FIGURE 3 68 Lifting the PCI E Card From the PCI Tray 4 Set the PCI E card aside on an antistatic mat 5 Consider your next step Chapter 3 Maintaining the Netra X4200 M2 Server 93 94 a If you are replacing the PCI E card continue to Installing the PCI E Card on page 94 a If you will not replace the PCI E card a Install a filler panel b Tighten the PCI E card securing screw 6 Perform the following tasks to bring the server back online Installing the Top Cover on page 126 Removing Antistatic Measures on page 127 Reinstalling the Server Chassis in the Rack on page 127 Reconnecting Cables to the Server on page 130 Powering On the Server on page 131 Installing the PCI E Card 1 Prepare the server for PCI E card installation See Powering Off the Server on page 28 Disconnecting Cables From the Server on page 29 Removing the Server From the Rack on page 30 Performing Antistatic Measures on page 31 Removing the Top Cover on page 33 Removing the PCI Tray and PCI E Ribbon Cables on page 34 2 Flip the PCI tray over place it on an antistatic mat and loosen the PCI E card securing screw FIGURE 3 67 Note The screw is captive and cannot be completely removed from the PCI tray 3
85. e any data protection in the event of disk failure It is primarily used to increase speed Note Once the number of disks in a RAID volume is set it cannot be changed 5 When the volume has been fully configured press C and select Save Changes then exit this menu to commit the changes The Configuration Utility will pause while the array is being created Creating a RAID 1 Volume A RAID 1 volume also referred to as Integrated Mirroring IM offers the ability to mirror data from one hard disk onto another one This can increase reliability by combining multiple disks into one logical volume Follow these steps to create a RAID 1 volume on an adapter that does not currently have a volume configured 1 In the Configuration Utility select an adapter from the Adapter List screen 2 3 Select the RAID Properties option When you are prompted to create either an IS volume or an IM volume select Create IM Volume The next screen shows a list of disks that can be added to a volume Move the cursor to the RAID Disk column To add a disk to the volume change the No to Yes by pressing the key key or space bar When the first disk is added the utility will prompt you to keep existing data or overwrite existing data 196 Netra X4200 M2 Server Service Manual May 2007 5 Press M to keep the existing data on the first disk or press D to overwrite it If you keep the existing data this is called
86. e assembly from its packaging and place it on an antistatic mat Move the cables as far out of the way as possible Pivot the front of the mass storage assembly down and lower the assembly into the chassis sliding it forward FIGURE 3 28 Chapter 3 Maintaining the Netra X4200 M2 Server 51 FIGURE 3 28 Setting the Mass Storage Assembly Into Place 4 Tighten the screws at the front of the chassis and the back of the mass storage assembly FIGURE 3 29 FIGURE 3 29 Tightening the Mass Storage Assembly Screws 52 Netra X4200 M2 Server Service Manual May 2007 5 Connect the following cables to the mass storage assembly FIGURE 3 24 a System fan a Hard drive fan a PCI tray power cable a Flex circuit Ribbon cable to power distribution board 6 Install the DVD drive and the hard drives See a Installing the DVD Drive on page 42 a Installing a Hard Drive on page 46 7 Close the front bezel 8 Consider your next step a If you installed the mass storage assembly as part of another procedure return to that procedure m Otherwise perform the following tasks to bring the server back online a Installing the PCI Tray on page 108 a Installing the Top Cover on page 112 a Removing Antistatic Measures on page 113 a Installing the Server Chassis in the Rack on page 114 a Reconnecting Cables to the Server on page 115 a Powering On the Server on page 116 Replacing the
87. eatures of the rear panel GbE ports 00010010L lt gt PCI EO Power connection T s SP NET MGT can port ort Grounding p lugs USB ports SP SERIAL MGT i port Rear Indicators FIGURE 1 3 Netra X4200 M2 Server Rear Panel 4 Netra X4200 M2 Server Service Manual May 2007 Netra X4200 M2 Server Components FIGURE 1 4 shows the locations of the Netra X4200 M2 server replaceable components with the top covers removed Power distribution board bottom Hard disk drive backplane top Power supplies 2 Fan tray 1 DVD drive Hard drives 2 4 HDD option available with no DVD Flex Circuit ribbon cable MB MacAddress pathway label i Service processor 7 Fan tray 0 DIMM LED Butto LED board CPUs heatsinks 2 Motherboard DIMMs up to 4 for each CPU FIGURE 1 4 Netra X4200 M2 Replaceable Component Locations Chapter 1 Introduction to the Netra X4200 M2 Server 5 FIGURE 1 5 Customer Replaceable Units Note that all FRUs are customer replaceable Netra X4200 M2 Server Service Manual May 2007 6 TABLE 1 2 Netra X4200 M2 Server FRU List Item No FRU Replacement Instructions Description FRU Name 1 Top cover Removing the Top Cover on page 33 2 PCI Tray M
88. ed circuit boards and hard disk drives contain components that are extremely sensitive to static electricity 3 If the server is in a rack slide it far enough from the rack so that you can remove the cover If you cannot safely view and access the motherboard remove the server from the rack 4 Remove the top cover from the server See Removing the Top Cover on page 33 5 Remove the PCI tray See Removing the PCI Tray and PCI E Ribbon Cables on page 34 6 Install the shorting jumper across the Clear CMOS header pins See FIGURE 2 6 for the Clear CMOS jumper location at J9 7 Wait 10 seconds then remove the shorting jumper This jumper removes battery power from the SouthBridge chipset where the CMOS settings are stored thereby removing the CMOS settings 8 Reinstall the cover to the server 9 Reconnect AC or DC power cords to the server The server powers up to standby power mode indicated when the Power OK LED on the front panel is flashing Using the Reset and NMI Switches Caution Do not use the Reset and NMI switches unless you are instructed to do so by authorized Sun service personnel The Non Maskable Interrupt NMI switch SW3 on the motherboard sends an NMI order to the CPUs which is used by Field Service for debugging activities at the request of Service personnel The button for this switch can be pushed by inserting a paper clip or similar stylus through the hole provided on the rea
89. ed video 2 GRN Green video 3 BLU Blue video 4 ID2 ID2 no connect 5 GND Ground 6 R_GND Red video return ground Z G_GND Green video return ground 8 B_GND Blue video return ground 9 KEY No pin 10 S_GND Sync return ground 11 IDO IDO no connect 12 ID1 SDA MONID1 13 HSYNC Horizontal sync 14 VSYNC Vertical syne 15 ID3 SCL MONID2 Appendix D Connector Pinouts 143 Alarm Port The alarm port on the alarm rear transition module uses a standard DB 15 connector In a telecommunications environment use this port to connect to the central office alarming system FIGURE D 6 shows the pin numbering of the alarm port and TABLE D 6 describes the pin signals Note The alarm port relay contacts are rated for 100 V 0 2 A maximum 8 1 ALARM anna 15 9 FIGURE D 6 Alarm Port Pin Numbering TABLE D 6 Alarm Connector Signals Pin Service Pin Service 1 NC 9 ALARM1_NC 2 NC 10 ALARM1_COM 3 NC 11 ALARM2_NO 4 NC 12 ALARM2_NC 5 ALARMO_NO 13 ALARM2_COM 6 ALARMO_NC 14 ALARM3_NO 7 ALARM0_COM 15 ALARM3_COM 8 ALARM1_NO CHASSIS FRAME GND Serial Attached SCSI Connector The Serial Attached SCSI SAS connector pins and their corresponding descriptions are shown in the figure and table in this section 144 Netra X4200 M2 Server Service Manual May 2007 Signal segment PinS7 PinS1 Power segment Pin P15 Pin S14 Pin S8 Backside signal segment FIGURE D 7 Serial Attached SCSI C
90. eded on page 26 Locations of the Netra X4200 M2 Components on page 26 Starting the Maintenance Procedures on page 28 Maintaining the PCI Tray on page 34 Replaceable Component Procedures on page 37 Replacing the Mass Storage Assembly on page 47 Replacing the DVD Drive on page 40 Replacing a Hard Drive on page 43 Replacing the System Fan Assembly on page 53 Replacing the Hard Drive Fan Assembly on page 58 Replacing the LED Board on page 62 Replacing the GRASP Board on page 66 Replacing the DIMM CPU Duct on page 68 Replacing Memory Modules DIMMs on page 71 Replacing a CPU and Heatsink on page 76 Replacing the Motherboard Assembly on page 82 Replacing a PCI X Card on page 88 Replacing the PCI E Card on page 92 Replacing a Power Supply on page 95 Replacing the Power Distribution Board on page 98 Replacing the Alarm Board on page 103 25 Tools and Supplies Needed The Netra X4200 M2 server can be serviced with the following items 26 No 2 Phillips screwdriver Antistatic wrist strap Ballpoint pen or other stylus to press the recessed Power button Long nosed pliers optional for Graphics Redirect and Service Processor GRASP board removal 8 mm screwdriver Locations of the Netra X4200 M2 Components FIGURE 3 1 shows the locations of the replaceable Netra X4200 M2 components that are documented
91. emarks of Sun Microsystems Inc in the U S and in other countries All SPARC trademarks are used under license and are trademarks or registered trademarks of SPARC International Inc in the U S and in other countries Products bearing SPARC trademarks are based upon an architecture developed by Sun Microsystems Inc AMD Opteron is a trademark or registered trademark of Advanced Microdevices Inc The OPEN LOOK and Sun Graphical User Interface was developed by Sun Microsystems Inc for its users and licensees Sun acknowledges the pioneering efforts of Xerox in researching and developing the concept of visual or graphical user interfaces for the computer industry Sun holds a non exclusive license from Xerox to the Xerox Graphical User Interface which license also covers Sun s licensees viho implement OPEN LOOK GUIs and otherwise comply with Sun s written license agreements U S Government Rights Commercial use Government users are subject to the Sun Microsystems Inc standard license agreement and applicable provisions of the FAR and its supplements DOCUMENTATION IS PROVIDED AS IS AND ALL EXPRESS OR IMPLIED CONDITIONS REPRESENTATIONS AND WARRANTIES INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE OR NON INFRINGEMENT ARE DISCLAIMED EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLY INVALID Copyright 2007 Sun Microsystems Inc 4150 Network Circle Santa Clara Californie
92. end of the memory socket are fully open rotated outward to accept the new DIMM 3 Align the notch in the bottom edge of the DIMM with the key in the DIMM socket See FIGURE 3 52 Netra X4200 M2 Server Service Manual May 2007 4 Press down evenly on both top corners of the DIMM until the ejectors snap over the cutouts in the left and right edges of the DIMM FIGURE 3 52 Note Install DIMMs in pairs into alternate slots FIGURE 3 52 Inserting the DIMM Into the Slot 5 Repeat steps 3 through 5 for all DIMMs to be installed 6 Consider your next step If you installed DIMMs as part of another procedure return to that procedure m If you are to only install DIMMs a Install the DIMM CPU duct See Installing the DIMM CPU Duct on page 69 b Perform the following tasks to bring the server back online a Installing the Top Cover on page 126 a Removing Antistatic Measures on page 127 m Reinstalling the Server Chassis in the Rack on page 127 a Reconnecting Cables to the Server on page 130 a Powering On the Server on page 131 Chapter 3 Maintaining the Netra X4200 M2 Server 75 76 Replacing a CPU and Heatsink Follow these steps to remove and replace a CPU and its heatsink in a Netra X4200 M2 server Supported components and their part numbers are subject to change over time For the most up to date list of replaceable components for these servers see the followin
93. erties option The properties of the current volume are displayed 3 If more than one volume is configured press Alt N to view the next array 4 To manage the current array press Enter when the Manage Array item is selected 198 Netra X4200 M2 Server Service Manual May 2007 Synchronizing an Array Synchronizing an array means that the firmware synchronizes the data on the secondary disk s with the data on the primary disk of the mirror Follow these steps to start a synchronization for a RAID 1 volume 1 Select Synchronize Array 2 Press Y to start the synchronization or N to cancel it Note If the server is rebooted before the volume synchronization is completed the resync resumes when the server boots Activating an Array An array can become inactive if for example it is removed from one controller or computer and moved to another one The Activate Array option enables you to reactivate an inactive array that has been added to a system This option is only available when the selected array is currently inactive 1 Select Activate Array 2 Press Y to proceed with the activation or press N to abandon it After a pause the array becomes active Deleting an Array Caution Before deleting an array back up all data on the array that you want to keep Follow these steps to delete a selected array 1 Select Delete Array 2 Press Y to delete the array or press N to abandon the deletion
94. four seconds to force main power off and enter standby power mode When main power is off the Power OK LED on the front panel will begin flashing indicating that the server is in standby power mode 28 Netra X4200 M2 Server Service Manual May 2007 Power button Power OK LED FIGURE 3 2 Power Button and Power OK LED Locations Caution When you use the Power button to enter standby power mode power is still directed to the GRASP board and power supply fans indicated when the Power OK LED is flashing To completely power off the server you must disconnect the AC or DC power cords from the back panel of the server Disconnecting Cables From the Server Caution The system supplies standby power to the circuit boards even when the system is powered off 1 Label all cables connected to the server 2 Disconnect the following cables as appropriate PCI X 0 PCI X 1 PCI X 2 Alarm PCI E 0 SER MGT Chapter 3 Maintaining the Netra X4200 M2 Server 29 a NET MGT a USB 1 USBO a NETO a NET1 a NET 2 a NET3 a Power supply 0 Power supply 1 handling internal components attach an electrostatic discharge ESD wrist strap to A Caution Before unplugging the AC or DC power cords from the server or the button snap grounding post inside the chassis just behind the mass storage assembly see FIGURE 3 10 for the location The system s printed circuit boards and hard disk drives con
95. g URL http sunsolve sun com handbook_pub Systems Caution Some AMD CPUs are released as Special Editions which might differ in wattage from non Special Edition versions of the CPU Do not mix Special Edition CPUs with non Special Edition versions Always make sure that all CPUs in the server have the same part number Removing a Netra X4200 M2 CPU and Heatsink 1 Power off the server as described in Powering Off the Server on page 28 2 If the server is in a rack slide it far enough from the rack so that you can remove the main cover If you cannot safely view and access the component remove the server from the rack 3 Remove the top cover as described in Removing the Top Cover on page 33 4 Identify which CPU and heatsink you are replacing The designation of the two CPUs in the server is shown in FIGURE 3 53 There is a fault LED on the motherboard for each CPU see FIGURE 3 53 for the LED location a LED is off CPU is operating properly a LED is lit amber CPU has encountered a voltage or heat error condition Netra X4200 M2 Server Service Manual May 2007 Back panel of server DIMM 3 DIMM 1 DIMM 2 DIMM 0 CPU fault LEDs 2 FIGURE 3 53 CPU and Fault LED Locations 5 Remove the CPU and heatsink from the motherboard a Hold down on the top of the heatsink to prevent it from tipping unevenly while you alternately loosen the four spring loaded mounti
96. g a Hard Drive 43 iv Netra X4200 M2 Server Service Manual May 2007 Installing a Hard Drive 46 Replacing the Mass Storage Assembly 47 Mass Storage Assembly Connectors 47 Removing the Mass Storage Assembly 49 Installing the Mass Storage Assembly 51 Replacing the System Fan Assembly 53 Removing the System Fan Assembly 54 Installing the System Fan Assembly 55 Replacing the Hard Drive Fan Assembly 58 Removing the Hard Drive Fan Assembly 58 Installing the Hard Drive Fan Assembly 60 Replacing the LED Board 62 Removing the LED Board 62 Installing the LED Board 64 Replacing the GRASP Board 66 Removing the GRASP Board 66 Installing the GRASP Board 67 Replacing the DIMM CPU Duct 68 Removing the DIMM CPU Duct 68 Installing the DIMM CPU Duct 69 Replacing Memory Modules DIMMs 71 Removing a DIMM 71 Netra X4200 M2 DIMM Population Rules 72 Supported DIMM Configurations For Netra X4200 M2 73 Installing a DIMM 74 Replacing a CPU and Heatsink 76 Removing a Netra X4200 M2 CPU and Heatsink 76 Installing a Netra X4200 M2 CPU and Heatsink 80 Contents v Replacing the Motherboard Assembly 82 Removing the Motherboard Assembly 82 Installing the Motherboard Assembly 86 Replacing a PCI X Card 88 Removing a PCI X Card 88 Installing a PCI X Card 90 Replacing the PCI E Card 92 Removing the PCI E Card 92 Installing the PCI E Card 94 Replacing a Power Supply 95 Removing a Power Supply 96 Installing a Power Supply 97 Replacing the Power Distribution
97. he Server on page 29 a Removing the Server From the Rack on page 30 a Performing Antistatic Measures on page 31 a Removing the Top Cover on page 33 2 Identify the PCI X card to remove loosen the appropriate securing screw FIGURE 3 63 and twist the green retention latches away from the card FIGURE 3 63 PCI Tray and Location of PCI Card Securing Screws Note The screws are captive and cannot be completely removed from the PCI tray 88 Netra X4200 M2 Server Service Manual May 2007 Note Both short and long green retention latches are provided with the default PCI tray assembly and may need to be repositioned to support cards depending on form factor that is short versus long or full height versus half height FIGURE 3 64 Short retention latch FIGURE 3 64 Locations of PCI Tray Screw and Retention Latches 3 Slide the PCI X card to the left and lift it out of the PCI tray FIGURE 3 65 FIGURE 3 65 Lifting the PCI X Card From the PCI Tray Set the PCI X card aside on an antistatic mat Chapter 3 Maintaining the Netra X4200 M2 Server 89 4 Consider your next step a If you are replacing the PCI X card continue to Installing a PCI X Card on page 90 a If you will not replace the PCI X card a Install a filler panel b Slide the PCI tray back into closed position c Tighten the PCI X card securing screw if it was removed for PCI E card service 5 Perform the follow
98. he bezel forward and down See FIGURE 3 5 2 Pull the bezel away from the chassis FIGURE 3 5 Opening the Front Bezel 34 Maintaining the PCI Tray Removing the PCI Tray and PCI E Ribbon Cables The PCI tray is a carrier for the PCI X and PCI E cards You need to remove the PCI tray to replace the following components a PCI E card a LED board a DIMM CPU duct a Alarm board a DIMMs CPUs a GRASP Battery a Mass storage array m System fans Motherboard assembly It is not necessary to remove the PCI tray for other components however when the PCI tray is removed additional working space is provided Netra X4200 M2 Server Service Manual May 2007 1 Disconnect the PCI tray cable at location J2 and loosen the thumbscrew adjacent to it FIGURE 3 6 Also disconnect the PCI E cables shown in FIGURE 3 6 PCI E cables FIGURE 3 6 Disconnecting the PCI Tray Power Cable and Loosening the Thumbscrew Note The thumbscrew is captive and cannot be fully removed from the PCI tray 2 Slide the PCI tray back about 1 inch 25 mm and lift up on the back edge FIGURE 3 7 Chapter 3 Maintaining the Netra X4200 M2 Server 35 FIGURE 3 7 Lifting the PCI Tray Removing the PCI E Cable Hold Down Bracket Loosen the three captive screws that hold the PCI E cable hold down bracket in position and lift the U plate up and off of the motherboard FIGURE 3 8 Note the ribbon cable and goldfinger locat
99. ice Identifier ID Esc Exit Menu FIGURE E 16 View Array Screen TABLE E 12 View Array Screen Field Descriptions LSI Logic MPT Setup Utility v6 02 00 00 3 FUJITSU MAV2073RCSUN72G 0301 Yes 4 FUJITSU MAV2073RCSUN72G 0301 Yes 1 of T LSILOGICLogical Volume 3000 IM 2 69618 Optimal RAID Hot Drive Disk Spr Status No Secondary No Primary F1 Shift 1 Help Enter Select Item Alt N Next Array C Create an array KKK KEK KR KEK KKK KKK KEK KK KEK KKK KKK KKK KKK KK KEK KKK KKK KEKE KKK KE KKK KEK KEK KKK KEKE KKK KEK KKK KKK KEKE EEK 2005 07 08 Pred Fail No Size MB 69618 69618 Field Description Array Identifier Type Scan Order Size MB Status The number of the array The identifier of the array The RAID type of the array The scan order of the array The size of the array The status of the array Appendix E Serial Attached SCSI BIOS Configuration Utility 187 TABLE E 142 View Array Screen Field Descriptions Continued Field Description Scan ID The order in which devices are scanned Device Identifier The ASCII device identifier string extracted from the device s inquiry data RAID Disk Specifies whether the disk is part of a RAID array Yes or No This field is grayed out under the following conditions e The disk does not meet the minimum requirements for use in a RAID array
100. in the server chassis OK to Remove 2o Fault se Activity FIGURE C 4 Hard Drive LEDs TABLE C 2 Hard Drive LEDs LED Color Description OK to blue e On The drive is ready for hot plug removal Remove e Off Normal operation Fault amber On The drive has a fault and requires attention e Off Normal operation Activity green e On Drive is receiving power Solidly lit if drive is idle e Flashing The drive is processing a command e Off Power is off Power Supply LEDs The power supply LEDs FIGURE C 2 and TABLE C 3 are located on the back of each power supply TABLE C 3 Power Supply LEDs LED Color Description Power OK green e On Normal operation DC output voltage is within normal limits e Off Power is off Fault amber On Power supply has detected a failure e Off Normal operation Input OK green e On Normal operation Input power is within normal limits e Off No input voltage or input voltage is below limits Appendix C Status Indicator LEDs 135 Ethernet Port LEDs The four 10 100 1000 Mbps Ethernet ports each have two LEDs as described in TABLE C 4 TABLE C 4 Ethernet Port LEDs LED Color Description Left LED Amber Speed indicator or e Amber On The link is operating as a Gigabit connection 1000 Green Mbps e Green On The link is operating as a 100 Mbps connection e Off The link is operating as a 10 100 Mbps
101. ing Examples AaBbCc123 The names of commands files Edit your login file and directories on screen Use 1s a to list all files computer output You have mail AaBbCc123 What you type when contrasted su with on screen computer output password AaBbCc123 Book titles new words or terms Read Chapter 6 in the User s Guide words to be emphasized These are called class options Replace command line variables You must be superuser to do this with real names or values To delete a file type rm filename The settings on your browser might differ from these settings Third Party Web Sites Sun is not responsible for the availability of third party web sites mentioned in this document Sun does not endorse and is not responsible or liable for any content advertising products or other materials that are available on or through such sites or resources Sun will not be responsible or liable for any actual or alleged damage or loss caused by or in connection with the use of or reliance on any such content goods or services that are available on or through such sites or resources Sun Welcomes Your Comments Sun is interested in improving its documentation and welcomes your comments and suggestions You can submit your comments by going to http www sun com hwdocs feedback Please include the title and part number of your document with your feedback Netra X4200 M2 Server Service Manual part number 820 0063 11
102. ing POST Options These instructions are optional but you can use them to change the operations that the server performs during POST testing 1 Initialize the BIOS Setup utility by pressing the F2 key while the system is performing the power on self test POST 2 When the BIOS Main Menu screen is displayed select the Boot menu 3 From the Boot Settings screen select Boot Settings Configuration 122 Netra X4200 M2 Server Service Manual May 2007 4 On the Boot Settings Configuration screen there are several options that you can enable or disable Quick Boot This option is disabled by default If you enable this the BIOS skips certain tests while booting such as the extensive memory test This decreases the time it takes for the system to boot System Configuration Display This option is disabled by default If you enable this the system configuration screen is displayed before booting begins Quiet Boot This option is disabled by default If you enable this the Sun Microsystems logo is displayed instead of POST codes Language This option is reserved for future use Do not change Add On ROM Display Mode This option is set to Force BIOS by default This option has effect only if you have also enabled the Quiet Boot option but it controls whether output from the Option ROM is displayed The two settings for this option are as follows a Force BIOS Remove the Sun logo and display Option ROM output a Keep Curren
103. ing tasks to bring the server back online a Installing the Top Cover on page 126 a Removing Antistatic Measures on page 127 a Reinstalling the Server Chassis in the Rack on page 127 a Reconnecting Cables to the Server on page 130 a Powering On the Server on page 131 Installing a PCI X Card 1 Prepare the server for PCI X card installation See a Powering Off the Server on page 28 a Disconnecting Cables From the Server on page 29 a Removing the Server From the Rack on page 30 a Performing Antistatic Measures on page 31 a Removing the Top Cover on page 33 2 Determine where you will install the PCI X card and loosen the appropriate securing screw FIGURE 3 63 Note The screws are captive and cannot be completely removed from the PCI tray Note PCI X slot 1 has one securing screw and no green latch 3 Remove the replacement PCI X card from its packaging and place it onto an antistatic mat 4 Ifa filler panel is installed remove it 90 Netra X4200 M2 Server Service Manual May 2007 5 Lower the PCI X card into position on the PCI tray then slide it to the right to seat it into the connector FIGURE 3 66 FIGURE 3 66 Installing the PCI X Card Into the PCI Tray 6 Tighten the PCI X card bracket screw Note The captive PCI card bracket screws are located on the sides of the PCI tray assembly for PCI E slot 0 and PCI X slot 1 only Al
104. ions on the motherboard FIGURE 3 9 FIGURE 3 8 Screw Locations and Removal of the PCI E cable Hold Down Bracket 36 Netra X4200 M2 Server Service Manual May 2007 PCI E1 J18 Unused PCI E3 J21 Unused FIGURE 3 9 Ribbon Cable and Goldfinger Board Locations on the Motherboard Replaceable Component Procedures Note All FRUs are customer replaceable Supported components and their part numbers are subject to change over time For the most up to date list of replaceable components for these servers see the following URL http sunsolve sun com handbook_pub Systems 1 Click on the name and model of your server 2 On the product page that opens for the server click on Full Components List for the list of components Caution Before handling components attach an ESD wrist strap to the button snap grounding post inside the chassis just behind the mass storage assembly see FIGURE 3 10 for the location The system s printed circuit boards and hard disk drives contain components that are extremely sensitive to static electricity Chapter 3 Maintaining the Netra X4200 M2 Server 37 Button snap grounding post FIGURE 3 10 Location of Button Snap Grounding Post Replacing the Battery Follow these steps to remove and replace the system battery Part numbers are subject to change over time For
105. ive 7 Netra X4200 M2 40 E electrostatic discharge ESD prevention 31 emergency shutdown 14 environmental specs Sun Fire X4100 120 202 Netra X4200 M2 Server Service Manual May 2007 Ethernet 10 100 connector pinouts 141 Ethernet 10 100 1000 connector pinouts 142 Ethernet ports LEDs 136 external LEDs 131 F Fan assembly Hard drive 7 system 7 fan assembly 7 installing 55 fan module connector pinouts 154 Fault LED bezel 134 hard drive 135 power supply 135 server 134 feature summary 1 firmware updates xi flex cable motherboard connector pinouts 147 Flex circuit 7 front bezel 33 front bezel removal 33 113 front I O interconnect cable connector pinouts 151 front panel 3 LED locations 132 LEDs 133 front panel figure 3 FRU names locations and descriptions 7 FTO fan FRU names 7 Fusion MPT SAS BIOS See SAS BIOS G graceful shutdown 14 Graphics Redirect and Service Processor GRASP 8 GRASP 8 GRASP board 66 power status LED 137 GRASP board replacement 66 H hard drive 7 fan assembly installing 60 removing 58 replacing 58 hot plugging 43 identification 44 installing 46 latch release button 44 LEDs 135 Activity 135 Fault 135 removing 43 replacing 43 HDD hard drive FRU names 7 heatsinks Sun Fire X4200 M2 76 hot spares 197 hot plugging hard drives 43 hot swapping power supplies 95 l indicators 131 Input OK LED 135 installing alarm bo
106. l other slots use green ertention latches for securing plug in cards 7 Using a Philips screwdriver remove and reposition green retention latches to properly secure the installed option cards 8 Perform the following tasks to bring the server back online Installing the Top Cover on page 126 Removing Antistatic Measures on page 127 Reinstalling the Server Chassis in the Rack on page 127 Reconnecting Cables to the Server on page 130 Powering On the Server on page 131 Chapter 3 Maintaining the Netra X4200 M2 Server 91 92 Replacing the PCI E Card Caution The total power consumption of all PCI cards combined is not to exceed 80 watts The maximum power of any one PCI card is 25 watts Removing the PCI E Card 1 Prepare the server for PCI E card removal See Powering Off the Server on page 28 Disconnecting Cables From the Server on page 29 Removing the Server From the Rack on page 30 Performing Antistatic Measures on page 31 Removing the Top Cover on page 33 Removing the PCI Tray and PCI E Ribbon Cables on page 34 Netra X4200 M2 Server Service Manual May 2007 2 Flip the PCI tray over place on an antistatic mat and loosen the PCI E card securing screw FIGURE 3 67 PCl e retention latch PCl e bracket securing screw FIGURE 3 67 PCI Tray flipped over and PCI E Card Securing Screw Location Note The screw is captiv
107. late are in the fully open position c Align the CPU in the socket as shown in FIGURE 3 57 Note Use the alignment keys in the CPU socket to match the alignment notches on the sides of the CPU See inset of FIGURE 3 57 d Gently set the CPU onto the pins in the socket 80 Netra X4200 M2 Server Service Manual May 2007 A A e When the CPU is fully seated in the socket pivot the hinged retainer plate down onto the top of the CPU f Pivot the release lever down and into the locked position at the side of the socket The release lever must lock down the retainer plate as you close the lever See FIGURE 3 56 for a view of how the lever locks down the edge of the plate g If you are reinstalling an existing CPU or heatsink use an alcohol pad to clean all old thermal grease from the component surface Caution Ensure that the thermal grease in the syringe supplied with the CPU is pliable and not stiff If your syringe of grease has aged the grease might be too stiff to adequately spread out and ensure thermal conductance h Use one syringe of thermal grease 0 5 g to carefully apply grease to the top of the CPU in three lines in the pattern shown in FIGURE 3 58 CPU surface Lines of thermal grease FIGURE 3 58 Required Pattern for Thermal Grease Application 2 Turn the heatsink upright and reinstall the four springs and mounting bolts Caution Avoid moving the heatsink after it has contacte
108. lectable parameters relating to NB SB such as timing parameters non cacheable regions and the shadow RAM cacheability and do any other NB SB PCIX OEM specific programming needed during Late POST Background scrubbing for DRAM and L1 and L2 caches are set up based on setup questions Get the DRAM scrub limits from each node Workaround for erratum 101 applied here 8D Build ACPI tables if ACPI is supported 8E Program the peripheral parameters Enable Disable NMI as selected 90 Late POST initialization of system management interrupt AO Check boot password if installed Al Clean up work needed before booting to OS A2 Takes care of runtime image preparation for different BIOS modules Fill the free area in F000h segment with OFFh Initializes the Microsoft IRQ Routing Table Prepares the runtime language module Disables the system configuration display if needed A4 Initialize runtime language module A7 Displays the system configuration screen if enabled Initialize the CPUs before boot which includes the programming of the MTRRs A8 Prepare CPU for OS boot including final MTRR values A9 Wait for user input at config display if needed AA Uninstall POST INT1Ch vector and INTO9h vector Deinitializes the ADM module AB Prepare BBS for Int 19 boot AC Any kind of Chipsets NB SB specific programming needed during End POST just before giving control to runtime code booting to OS Programmed the system BIOS 0F0000h shadow RAM
109. ler type PCI Slot The PCI slot in which the controller is located PCI Address The PCI address assigned to the adapter by the system BIOS Bus value has range 0x00 OxFF 0 255 decimal Device value has range 0x00 0x1F 0 31 decimal Function has range 0x00 0x7 0 7 decimal Appendix E Serial Attached SCSI BIOS Configuration Utility 165 TABLEE 4 Adapter Properties Screen Field Descriptions Continued Field Description MPT Firmware Revision SAS Address Status Boot Order Boot Support RAID Properties SAS Topology Advanced Adapter Properties The Fusion MPT firmware version and type IR or IT The SAS Address assigned to this adapter Indicates whether an adapter is eligible for LSI Logic software control or whether it is reserved for control by non LSI Logic software Enabled The BIOS is either currently controlling the adapter or will attempt to control the adapter upon reload e Disabled The BIOS is either not controlling the adapter or will discontinue control of the adapter upon reload Whether Enabled or Disabled the user can still view and modify settings for the adapter The Boot Support setting in the Adapter Properties menu can be used to change the status of this setting The BIOS must be reloaded the system must be rebooted in order for a new Boot Support setting to take effect Error The BIOS encountered a problem with the adapter Adapter settings can be viewed and
110. lts left and rear command provides details about any faults that cause this indicator center to be lit front upper green e On Drives are receiving power Solidly lit if drive is idle left e Flashing Drives are processing a command e Off Power is off front upper Turns the host system on and off This button is recessed to prevent left accidental server power off Use the tip of a pen to operate this button front left red Indicates a critical alarm Refer to the server administration guide for a description of alarm states front left red Indicates a major alarm front left amber Indicates a minor alarm front left amber Indicates a user alarm rear center green The LED provides the following indications e Off The system is unavailable Either it has no power or ALOM is not running e Steady on Indicates that the system is powered on and is running it its normal operating state e Standby blink Indicates that the service processor is running while the system is running at a minimum level in Standby mode and is ready to be returned to its normal operating state e Slow blink Indicates that a normal transitory activity is taking place It might mean that the system diagnostics are running or that the system is booting 134 Netra X4200 M2 Server Service Manual May 2007 Hard Drive LEDs The hard drive LEDs FIGURE C 4 and TABLE C 2 are located on the front of each hard drive that is installed
111. m the default 2 3 position markings on the board say Ontario This is the required position for operation of the Netra X4200 M2 server Installing the Power Distribution Board 1 Remove the replacement power board from its packaging and place it on an antistatic mat 2 Lower the power board into the chassis aligning the board s holes with the standoffs in the chassis FIGURE 3 75 100 Netra X4200 M2 Server Service Manual May 2007 FIGURE 3 75 Lowering the Power Board Into the Chassis 3 Install the five screws and two bus bar screws to secure the power board to the chassis FIGURE 3 76 Chapter 3 Maintaining the Netra X4200 M2 Server 101 Bus bar screws o FIGURE 3 76 Securing the Power Board to the Chassis Note Tighten the two power board screws firmly 4 Install the mass storage assembly the hard drives the DVD drive and the power supplies See Installing the Mass Storage Assembly on page 51 Installing a Hard Drive on page 46 Installing the DVD Drive on page 42 Installing a Power Supply on page 97 5 Perform the following tasks to bring the server back online See Installing the Top Cover on page 112 Closing the Front Bezel on page 113 Removing Antistatic Measures on page 113 Installing the Server Chassis in the Rack on page 114 Reconnecting Cables to the Server on page 115 Powering On the Server on page 116 102 Netr
112. mand to delete all partitions Then reboot the system to clear memory Otherwise the old partitioning data will be reused Invalid DWORDs The number of invalid dwords that have been received outside of PHY reset sequences since the last PHY Link Error Reset Loss of DWORD Sync The number of times since the last PHY Link Error Reset that DWORD synchronization was lost and the link reset sequence occurred Running Disparity Errors The number of DWORDS with running disparity errors that have been received outside of PHY reset sequences since the last PHY Link Error Reset PHY Reset Errors The number of times the PHY reset sequence has failed since the last PHY Link Error Reset Link error count threshold values When a Link Error Count exceeds a Threshold Count within the Threshold Time secs the Fusion MPT FW may reduce the link rate Press Enter on any of these fields to modify the value Time in seconds over which to apply the Threshold Count When a Link Error Count exceeds a Threshold Count within the Threshold Time secs the Fusion MPT FW may reduce the link rate Press Enter on any of these fields to modify the value Press Enter to view and modify Advanced Device Properties see Advanced Device Properties Screen on page 176 Press Enter to view and modify PHY properties see PHY Properties Screen on page 179 Press Enter to restore the default values for all items on this screen Ap
113. mer interrupt Traps INT1Ch vector to POSTINT1ChHandlerBlock Co Early CPU Init Start Disable Cache Init Local APIC C1 Set up boot strap processor information C2 Set up boot strap processor for POST This includes frequency calculation loading BSP microcode and applying user requested value for GART Error Reporting setup question C3 Errata workarounds applied to the BSP 78 amp 110 C5 Enumerate and set up application processors This includes microcode loading and workarounds for errata 78 110 106 107 69 63 C6 Re enable cache for boot strap processor and apply workarounds in the BSP for errata 106 107 69 and 63 if appropriate In case of mixed CPU steppings errors are sought and logged and an appropriate frequency for all CPUs is found and applied NOTE APs are left in the CLI HLT state C7 The HT sets link frequencies and widths to their final values This routine gets called after CPU frequency has been calculated to prevent bad programming 0A Initializes the 8042 compatible Keyboard Controller 0B Detects the presence of PS 2 mouse 0C Detects the presence of Keyboard in KBC port OE Testing and initialization of different Input Devices Also update the Kernel Variables Traps the INTO9h vector so that the POST INT09h handler gets control for IRQ1 Decompress all available language BIOS logo and Silent logo modules 126 Netra X4200 M2 Server Service Manual May 2007 TABLE B 2 POS
114. modified but the available information and functionality may be limited The order in which adapters will boot when the system has more than one adapter Up to four of the total adapters in a system may be selected as bootable Indicates whether an adapter is eligible for LSI Logic software control or whether it is reserved for control by non LSI Logic software The options are e Enabled BIOS amp OS default Both the BIOS and OS driver will control the adapter e Enabled BIOS Only The BIOS will control the adapter OS drivers will not control it Some OS drivers do not support this setting For example there is no way to disable an adapter in a Windows driver e Enabled OS Only The BIOS will not control the adapter the OS driver will control the adapter e Disabled The BIOS will not control the adapter when loaded However the adapter will still be visible through the Configuration Protocol Changes to this setting are reflected in the Status field on the main Adapter List menu The new setting does not take effect until the BIOS is reloaded that is until the system is rebooted Press Enter on this field to access this screen Press Enter on this field to access this screen Press Enter on this field to access this screen 166 Netra X4200 M2 Server Service Manual May 2007 SAS Topology Screen The SAS Topology screen presents a view of the adapter s SAS hierarchy as shown in FIGURE E 4 You can scroll right
115. n PowerNow Configuration RemoteAccess Configuration USB Configuration Removable Drives CD DVD Drives FIGURE 2 5 Netra X4200 M2 Server BIOS Menu Tree i SouthBridge Configuration Chipset menu Exit menu NorthBridge Configuration Memory Configuration ECC Configuration IOMMU Mode Chapter 2 Powering On and Configuring BIOS Settings 19 20 Resetting LOM and BIOS Passwords This procedure describes how to reset the Administrator password root password for the ILOM Service Processor to the default after it has been set once during initial setup Note This procedure simultaneously removes any BIOS password that was set 1 Shut down the server to standby power mode by using a ballpoint pen or other stylus to press and release the recessed Power button on the front panel See Powering Off the Server on page 14 2 Disconnect the AC or DC power cords from the server Caution Before handling components attach an electrostatic discharge ESD wrist strap to the grounding post that is built into the rear of the chassis see FIGURE 1 3 for the location The system s printed circuit boards and hard disk drives contain components that are extremely sensitive to static electricity 3 If the server is in a rack slide it far enough from the rack so that you can remove the cover If you cannot safely view and access the
116. n page 28 m Disconnecting Cables From the Server on page 29 m Removing the Server From the Rack on page 30 m Performing Antistatic Measures on page 31 m Removing the Top Cover on page 33 1 After you remove the top cover open the bezel Press the green tabs on either side of the bezel and pull the bezel forward and down FIGURE 3 12 FIGURE 3 12 Opening the Bezel 40 Netra X4200 M2 Server Service Manual May 2007 2 Insert a small plastic probe into the opening at the back of the DVD drive FIGURE 3 13 FIGURE 3 13 Inserting the Probe at the Back of the DVD Drive 3 Push the release tab to the left and pull the probe forward freeing the DVD drive FIGURE 3 14 Note Do not pull on the DVD faceplate which could come loose if pushed from the back with the probe FIGURE 3 14 Releasing the DVD Drive 4 Remove the DVD drive from the mass storage assembly and set it aside on an antistatic mat Chapter 3 Maintaining the Netra X4200 M2 Server 41 5 Consider your next step a If you removed the DVD drive as part of another procedure return to that procedure a Otherwise continue to Installing the DVD Drive on page 42 Installing the DVD Drive 1 Remove the replacement DVD drive from its packaging and place the drive on an antistatic mat 2 Hold the release tab to the left and insert the DVD drive into the mass storage assembly FIGURE 3 15 FIGURE 3 15 Inserting the
117. n page 68 a System Fan assembly Removing the System Fan Assembly on page 54 a DIMMs Removing a DIMM on page 71 Alarm board Replacing the Alarm Board on page 103 m Graphics Redirect and Service Processor GRASP board Removing the GRASP Board on page 66 Netra X4200 M2 Server Service Manual May 2007 3 Disconnect the cables from the following connectors on the motherboard assembly FIGURE 3 59 a Flex Circuit J7 a Front I O J23 Flex Circuit J7 Front I O J23 FIGURE 3 59 Disconnecting the Cables From the Motherboard Assembly 4 Use an 8mm nut driver to remove the two bus bar nuts and six other screws that secure the motherboard assembly to the chassis See FIGURE 3 60 Chapter 3 Maintaining the Netra X4200 M2 Server 83 mZ 2 bus bar screws wm Ee FIGURE 3 60 Motherboard Securing Screws and Bus Bar Screw Locations 5 Use the lifting handle to raise the forward edge of the board until it has cleared the bus bar studs Caution When lifting the board use caution to avoid damaging the light pipes and connectors on the rear edge of the motherboard 6 Slide the board toward the front of the chassis until the connectors and light pipes are clear of the chassis back panel gasketing Then raise the motherboard and remove it from the chassis 84 Netra X4200 M2 Server Service Manual May
118. nd sizing in boot block cache disabled IO APIC enabled 01d4 Test base 512KB memory Adjust policies and cache first 8MB 01d5 Boot block code is copied from ROM to lower RAM BIOS is now executing out of RAM 01d6 Key sequence and OEM specific method is checked to determine if BIOS recovery is forced If next code is E0 BIOS recovery is being executed Main BIOS checksum is tested 01d7 Restoring CPUID moving boot block runtime interface module to RAM determine whether to execute serial flash 01d8 Decompressing runtime module into RAM Storing CPUID information in memory 01d9 Copying main BIOS into memory Olda Giving control to BIOS POST 0004 Check CMOS diagnostic byte to determine if battery power is OK and CMOS checksum is OK If the CMOS checksum is bad update CMOS with power on default values 00c2 Set up boot strap processor for POST This includes frequency calculation loading BSP microcode and applying user requested value for GART Error Reporting setup question 00c3 Errata workarounds applied to the BSP 78 amp 110 00c6 Re enable cache for boot strap processor and apply workarounds in the BSP for errata 106 107 69 and 63 if appropriate 00c7 HT sets link frequencies and widths to their final values 000a Initializing the 8042 compatible Keyboard Controller 000c Detecting the presence of Keyboard in KBC port 000e Testing and initialization of different Input Devices Traps the INTO9h vector so that th
119. ndicates whether an adapter has nonvolatile memory NVM IO Port Address Chip Revision ID Spinup Delay associated with it An adapter s configuration is stored in its associated NVM The I O Port Address used to communicate with the adapter The system BIOS assigns this number The Revision ID of this adapter The number of seconds to wait between spinups of devices attached to this adapter Staggered spinups balance the total electrical current load on the system during boot The default value is 2 seconds with choices between 1 and 10 seconds 174 Netra X4200 M2 Server Service Manual May 2007 TABLEE 8 Advanced Adapter Properties Screen Field Descriptions Continued Field Description CHS Mapping Link Error Settings Threshold Count Threshold Time secs Advanced Device Properties PHY Properties Restore Defaults Defines how the Cylinder Head Sector values are mapped onto a disk without pre existing partition information CHS Mapping allows two settings e SCSI Plug and Play Mapping default automatically determines the most efficient and compatible mapping e Alternate CHS Mapping utilizes an alternate possibly less efficient mapping that may be required if a device is moved between adapters from different vendors Note Neither of these options has any effect after a disk has been partitioned using the FDISK command To change the CHS Mapping on a partitioned disk use the FDISK com
120. nel SAS RAID disk controller e Four 10 100 1000Mbps Ethernet ports RJ 45 connectors e One 100BASE T Ethernet management port RJ 45 connector e One RS 232 serial port RJ 45 connector e One PCI Express slot for MD2 low profile cards support x1 x4 and x8 width cards e Three full height PCI X slots for 64 bit 133 MHz 3x 2x full length 1x half length e Two USB 2 0 ports e One VGA video port Internal slim DVD drive with 2x HDD option Two 550W power supplies DC or AC option Four fail safe dry contact telco alarms critical major minor and user Two fan modules containing five fans also one fan in each power supply 2 Netra X4200 M2 Server Service Manual May 2007 Netra X4200 M2 Server Orientation This section contains illustrations that you can use to become familiar with the components of the Netra X4200 M2 server Netra X4200 M2 Server Front Panel Features FIGURE 1 1 and FIGURE 1 2 show the features of the front panel User controlled System Fan Panels 4 HDD Configuration telco alarm LEDs Power Button LEDs go aomoole FIGURE 1 1 Netra X4200 M2 Server Front Panel 4HDD 2 HDD 1 DVD Configuration LS a a FIGURE 1 2 Netra X4200 M2 Server Front Panel 2 HDD 1 DVD Chapter 1 Introduction to the Netra X4200 M2 Server 3 Netra X4200 M2 Server Rear Panel Features FIGURE 1 3 shows the f
121. ng screws that secure the heatsink to the motherboard Turn the screws 180 degrees at a time then remove the screws when they are detached See FIGURE 3 54 and FIGURE 3 55 Chapter 3 Maintaining the Netra X4200 M2 Server 77 The four screws are circled in red FIGURE 3 55 Removing the Heatsink b Twist the heatsink slightly to lift it off of the board Turn the heatsink upside down and allow the spring in each of the four mounting holes to fall out into your hand 78 Netra X4200 M2 Server Service Manual May 2007 Note Set the heatsink upside down on a clean flat surface to prevent the thermal grease from contaminating other components c Pull the CPU socket lever slightly away from the socket See FIGURE 3 56 d Pivot the lever up into the fully open vertical position FIGURE 3 56 Releasing the CPU Socket Lever e Open the hinged plate that covers the CPU until it is in the fully open position and lift the CPU out of the socket leaving the lever in the vertical open position See FIGURE 3 57 Chapter 3 Maintaining the Netra X4200 M2 Server 79 FIGURE 3 57 Removing the CPU From the Socket Installing a Netra X4200 M2 CPU and Heatsink 1 Install the new CPU and heatsink Note Mixing CPU speeds or mixing dual core CPUs with single core CPUs is not supported Use two identical CPUs in your server a Unpack the new CPU and heatsink b Ensure that the CPU socket release lever and retainer p
122. ng systems will shut down to standby power mode immediately Emergency shutdown Press and hold the Power button for four seconds to force main power off and to enter standby power mode When main power is off the Power OK LED on the front panel will begin flashing indicating that the server is in standby power mode still directed to the Graphics Redirect and Service Processor GRASP board and power supply fans The Power OK LED flashes during standby power mode To completely power off the server you must disconnect the AC or DC power cords from the back of the power supplies A Caution When you use the Power button to enter standby power mode power is 14 Netra X4200 M2 Server Service Manual May 2007 Configuring BIOS Settings This section describes how to view and or modify the Basic Input Output System BIOS settings For a description of BIOS Setup screens see BIOS Setup Screens Summary on page 18 The BIOS has a Setup utility stored in the BIOS flash memory The Setup utility reports system information and can be used to configure the BIOS settings The configured data is provided with context sensitive Help and is stored in the system s battery backed CMOS RAM If the configuration stored in the CMOS RAM is invalid the BIOS settings will default to the original state specified at the factory The BIOS Setup utility contains seven menu screens which are displayed in the following order Main Advanced PCI
123. ng the hard drive continue to Installing a Hard Drive on page 46 If you are not replacing the hard drive perform administrative tasks to configure the server to operate without the hard drive Installing a Hard Drive 1 Remove the replacement hard drive from its packaging and place the drive on an antistatic mat 2 Align the replacement drive to the drive slot The hard drive is physically addressed according to the slot in which it is installed See FIGURE 3 21 It is important to install a replacement drive in the same slot as the drive that was removed 3 Slide the drive into the bay until it is fully seated FIGURE 3 21 FIGURE 3 21 Installing the Hard Drive Into the Server 4 Close the latch to lock the drive in place 5 Close the front bezel FIGURE 3 22 46 Netra X4200 M2 Server Service Manual May 2007 FIGURE 3 22 Closing the Bezel 6 Perform administrative tasks to reconfigure the hard disk drive The procedures that you perform at this point depend on how your data is configured You might need to partition the drive create file systems load data from backups or have the drive updated from a RAID configuration Replacing the Mass Storage Assembly Mass Storage Assembly Connectors FIGURE 3 23 identifies the five key connections that must be made on the mass storage assembly The corresponding connections are 1 go PE w S Flex circuit connector System fan connector Ribb
124. nimal information e Display adapters amp installed devices Support Interrupt This option allows you to prevent a hook on INT40 if required Possible values are e Hook interrupt default e Bypass interrupt hooks Restore Defaults Press Enter to restore the default settings 164 Netra X4200 M2 Server Service Manual May 2007 Adapter Properties Screen The Adapter Properties screen allows you to view and modify adapter settings It also provides access to all other screens FIGURE E 3 shows an example of the Adapter Properties screen TABLE E 4 describes the fields of the screen KEKKKKKKKKKKKKKK KKK KKK KKK KKK KKK KKK KKK KK KKK KEK KK KKK KEK KK KKK KEKE KK KKKKKKKKKKKKKKKKKK LSI Logic MPT Setup Utility v6 02 00 00 2005 07 08 Adapter Properties SAS1064 Adapter SAS1064 x PCI Slot 00 x PCI Address Bus Dev Func 02 03 00 x A MPT Firmware Revision 1 04 00 00 IR il SAS Address 50003BA0 000003BA a X Status Enabled k Boot Order 0 Boot Support Enabled BIOS amp OS i RAID Properties SAS Topology iS Advanced Adapter Properties Esc Exit Menu F1 Shift 1 Help a Enter Select Item Change Item z KKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKK FIGURE E 3 Adapter Properties Screen TABLEE 4 Adapter Properties Screen Field Descriptions Field Description Adapter The specific LSI Logic SAS control
125. nitialization Press Enter to restore the default values for all items on this screen PHY Properties Screen The PHY Properties screen FIGURE E 13 allows you to view and modify PHY specific settings TABLE E 10 describes the fields of the screen Note The Link Error Settings values on this screen only display the current values for this PHY and cannot be modified To modify the Threshold values return to the Advanced Adapter Properties screen Appendix E Serial Attached SCSI BIOS Configuration Utility 179 KREKKKKKKKKKKKKKKE KK KKK KKK K KKK KKK KKK KKK KK KKK KKK KKK KEKE KKK KKK KEKE KKKKKKKKKKKKKKKKKK LSI Logic MPT Setup Utility v6 02 00 00 2005 07 08 PHY Properties SAS1064 x PHY 2 3rd of 4 PHYs SAS Port 2 Link Status Enabled 3 0 Gbps Discovery Status 00000000 7 Device Identifier FUJITSU MAV2073RCSUN72G 0301 Scan Order 2 Device Information SAS SAS Address 500000E0 10D26642 Link Error Link Error Threshold Threshold Settings Count Count Time Secs pa Invalid DWORDs 0 0 0 hi Loss of DWORD Sync 0 0 0 Running Disparity Errors 0 0 0 z x PHY Reset Errors 0 0 0 Reset Link Error Counts Esc Exit Menu F1 Shift 1 Help Enter Reset Phy error logs Alt N Next Phy Alt P Previous Phy K KEKE KK KEKE KKK KEK KKK KKK KKK KKK KK KEK KK KEK KK KKK KKK KK KEK KKK KEK KEK KEK KEK KEK KKK KKK KEKE KK KK KK KKEKKEKEEK FIGURE
126. nother procedure return to that procedure a Otherwise perform the following tasks to bring the server back online a Installing the Top Cover on page 126 a Removing Antistatic Measures on page 127 a Reinstalling the Server Chassis in the Rack on page 127 a Reconnecting Cables to the Server on page 130 a Powering On the Server on page 131 70 Netra X4200 M2 Server Service Manual May 2007 Replacing Memory Modules DIMMs Follow these steps to remove and replace the server s dual inline memory modules DIMMs Removing a DIMM 1 Prepare the server for DIMM removal See a Powering Off the Server on page 28 a Disconnecting Cables From the Server on page 29 a Removing the Server From the Rack on page 30 a Performing Antistatic Measures on page 31 m Removing the Top Cover on page 33 Note You will only need to slide the PCI tray back for this procedure 2 Flip the DIMM CPU duct open DIMMs are located underneath See FIGURE 3 49 FIGURE 3 49 Flipping the DIMM CPU Duct open 3 Identify the DIMM to remove and press the ejector levers open releasing the DIMM FIGURE 3 50 Chapter 3 Maintaining the Netra X4200 M2 Server 71 72 SUNSA 2405 O49 MMEM L gas FIGURE 3 50 Releasing and removing the DIMM For the Netra X4200 M2 server you can view the DIMM fault LEDs without the power cords attached These LEDs can be lit by a capacito
127. nouts 153 powering off the server 14 powering on the server 12 power on self test See POST product updates xi PSO PS1 power supply FRU names 7 R RAID activating an array 199 creating RAID 0 volume 195 creating RAID 1 volume 196 creating second RAID volume 198 deleting an array 199 locating a disk drive 200 managing hot spares 197 synchronizing arrays 199 viewing RAID volume properties 198 redirecting console output 121 related documentation xii removing alarm board 103 antistatic measures 113 cable hold down bracket 36 DIMM CPU duct 68 hard drive 43 hard drive fan assembly 58 LED board 62 mass storage assembly 49 PCI tray 34 PCI E card 92 PCI X card 88 power distribution board 98 supply 96 server from rack 30 system fan assembly 54 replaceable component locations Netra X4200 M2 26 replacing alarm board 103 DIMM CPU duct 68 hard drive 43 hard drive fan assembly 58 LED board 62 mass storage assembly 47 motherboard assembly 82 PCI E card 92 PCI X card 88 power distribution board 98 supply 95 system fan assembly 53 Reset switch SW3 23 S safety guidelines xi SAS BIOS activating a RAID array 199 configuration tasks 195 Configuration Utility screens 159 creating RAID 0 volume 195 creating RAID 1 volume 196 creating second RAID volume 198 deleting a RAID array 199 exiting Configuration Utility 191 initialize with BIOS Boot Specification 158 locating a RAI
128. nu Exit the Configuration Utility and Reboot sg Esc Exit Menu F1 Shift 1 Help z KREKKKKKKKKKKKKKKKKKE KKK KK KKK KK KKK KKK KK KKK KK KKK KKK KK KKK KKK KKKKKRKKKKKKKKKKEKKKKKKK FIGURE E 18 Exit Screen RAID Implementation and Support The LSISAS1064 controller supports the Integrated RAID hardware solution which is a highly integrated low cost RAID solution It is designed for systems requiring redundancy and high availability but not requiring a full featured RAID implementation Integrated RAID includes Integrated Mirroring IM or RAID 1 and Integrated Striping IS or RAID 0 technology Integrated RAID is OS independent easy to install and configure and does not require a special driver A RAID Volume is seen as a single drive by the host BIOS and OS 192 Netra X4200 M2 Server Service Manual May 2007 The LSISAS1064 controller is based on the Fusion MPT Message Passing Technology architecture The Fusion MPT architecture requires only a thin device driver that is independent of the I O bus LSI Logic provides the device drivers for various operating environments The ILOM Service Processor monitors the GPIOs from the SAS1064 controller If the controller indicates a failure the service processor lights the fault LED on the corresponding disk drive and logs the error in the SP event log Automatic Data Resynchronization and
129. o one logical volume Note Use RAID 0 with caution The only advantage of RAID 0 is to improve the overall disk performance by striping data over several disk drives By doing this it decreases reliability because the failure of any drive within the striped volume results in a complete loss of data In addition any disk drive included in a RAID 0 volume becomes non hot swappable Follow these steps to create a RAID 0 volume on an adapter that does not currently have a volume configured 1 In the Configuration Utility select an adapter from the Adapter List screen 2 Select the RAID Properties option 3 When you are prompted to create either an IS volume or an IM volume select Create IS Volume The next screen shows a list of disks that can be added to a volume Appendix E Serial Attached SCSI BIOS Configuration Utility 195 4 Move the cursor to the RAID Disk column To add a disk to the volume change the No to Yes by pressing the key key or space bar As disks are added the Array Size field changes to reflect the size of the new volume There are several limitations when creating a RAID 0 volume All disks must be SAS with SMART support Disks must have 512 byte blocks and must not have removable media There must be at least two drives in a valid volume No more than eight drives are allowed in a volume Hot spare drives are not allowed for RAID 0 volumes Note RAID 0 does not provid
130. ock Devices Removable IO Timeout for Sequential Devices IO Timeout for Other Devices Description The maximum number of devices attached to the adapter for which to install a pre OS I O interface The specified number of devices in the adapter s device scan order list will have an I O interface installed An installed I O interface is defined as INT 13H X86 platforms allow a maximum of 24 INT 13h devices per system Therefore fewer than the specified number of INT 13h devices may be installed The default for X86 is 24 devices with a range of 0 24 allowed The maximum number of targets that can simultaneously spin up The IOC must delay by the time indicated in the spin up delay field before it starts spin up of the next set of targets A value of 0 in this field is treated the same as a value of 1 The time in seconds 0 999 0 no timeout that the host uses to timeout I Os for the following devices with nonremovable media e SCSI Device Type 00h Direct Access e SCSI Device Type 04h Write Once e SCSI Device Type 07h Optical e SCSI Device Type OEh Simplified Direct Access The time in seconds 0 999 0 no timeout that the host uses to timeout I Os for the following devices with removable media e SCSI Device Type 00h Direct Access e SCSI Device Type 04h Write Once e SCSI Device Type 05h CD ROM e SCSI Device Type 07h Optical e SCSI Device Type OEh Simplified Direct Access The time in se
131. on cable connector to the power distribution board Hard drive fan connector PCI tray power cable Note Do not remove the DVD connector Chapter 3 Maintaining the Netra X4200 M2 Server 47 4 5 1 DVD Connection Do not remove FIGURE 3 23 Five Key Connections of the Mass Storage Assembly FIGURE 3 24 shows how the five key connections look when the cables are plugged in i t Ribbon cable Hard Drive Fan Connector to PDB System Fan PCI Tray Connector Power Cable Flex Circuit 4 HDD DVD Connection Do not remove FIGURE 3 24 Populated Mass Storage Assembly Connectors FIGURE 3 25 shows an angled perspective of the path of the flex circuit connector from the motherboard to the 2 and 4 hard drive locations on the hard drive backplane 48 Netra X4200 M2 Server Service Manual May 2007 Note Flex circuit cable assembly passes through cutout in chassis 4 HDD wall 2 HDD Motherboard Connection System Fan Connector DIMM locations FIGURE 3 25 Path of the Flex Cable From Motherboard to 2 and 4 HDD Connections Removing the Mass Storage Assembly 1 Prepare the server for mass storage assembly removal See a Powering Off the Server on page 28 a Disconnecting Cables From the Server on page 29 a Removing the Server From the Rack on page 30 a Performing Antistatic Measures on page 31 a Removing the Top Cover on page 33 2 Remove the DVD drive and all the har
132. onfiguration Utility This message remains on the screen for about five seconds giving you time to start the utility If you press Ctrl C the message changes to Please wait invoking LSI Logic Configuration Utility 158 Netra X4200 M2 Server Service Manual May 2007 After a brief pause the computer monitor displays the Main menu of the Fusion MPT SAS BIOS Configuration Utility These messages may appear during the boot process m Adapter removed from boot order This message appears when an adapter has been removed from the system or has been relocated behind a PCI bridge m Adapter configuration may have changed reconfiguration is suggested This message appears if none of the information in the NVRAM is valid m Updating Adapter List This message appears when fewer than four adapters are in the boot order and more adapters exist than are shown Caution The SAS BIOS Configuration Utility is a powerful tool If while using it you disable all of the controllers press Ctrl E or Ctrl A on versions earlier than 5 00 after memory initialization during reboot to reenable and reconfigure the controllers Note Some devices detected by the Configuration Utility cannot be controlled by the SAS BIOS Devices such as tape drives and scanners require that a device driver specific to that device be loaded However the SAS BIOS Configuration Utility does enable you to modify parameters for these devices
133. onnector TABLE D 7 Serial Attached SCSI Connector Pinouts Segment Pin Number Pin Name Description Signal S1 Gnd Second mate ground t Peen S2 TX Positive side of transmit to hard drive S3 TX Negative side of transmit to hard drive S4 Gnd Second mate ground S5 RX Negative side of receive from hard drive S6 RX Positive side of receive from hard drive S7 Gnd Second mate ground Appendix D Connector Pinouts 145 TABLE D 7 Serial Attached SCSI Connector Pinouts Continued Segment Pin Number Pin Name Description Backside S8 Gnd Second mate ground a S9 Not used S10 Not used S11 Gnd Second mate ground S12 Not used 13 Not used S14 Gnd Second mate ground Power P1 3 3 V Not used segment P2 3 3 V Not used P3 3 3 V Not used P4 Gnd First mate ground P5 Gnd Second mate ground P6 Gnd Second mate ground P7 5 0 V Pre charge second mate P8 5 0 V Third mate 5 V P9 5 0 V Third mate 5 V P10 Gnd Second mate ground P11 Reserved Not used P12 Gnd First mate ground P13 12 0 V Pre charge second mate P14 12 0 V Third mate 12 V P15 12 0 V Third mate 12 V 146 Netra X4200 M2 Server Service Manual May 2007 Flex Cable Motherboard Connector The flex cable flex circuit motherboard connector pins and their corresponding descriptions are shown in the figure and table in this section Pin 40 Pin 41 Front of motherboard FIGURE D 8 Flex Cable Motherboard Connector TABLE D 8 Flex Cable Motherboard Connector Pinout
134. otherboard e Off CPU is operating properly e Lit amber CPU has encountered a voltage or heat error condition GRASP Board Power Status This LED has two states LED e Off Standby power is not reaching the GRASP board e Lit green 3 3V standby power is reaching the GRASP board Appendix C Status Indicator LEDs 137 138 Netra X4200 M2 Server Service Manual May 2007 APPENDIX D Connector Pinouts This appendix contains information about the connector pinouts USB Connector The USB connector pins and their corresponding descriptions are shown in the figure and table in this section TE E E F FIGURE D 1 USB Connector TABLE D 1 USB Connector Pinouts Pin Number Pin Name Description 1 5V 5V supply 2 Data Negative side of differential for data 3 Data Positive side of differential for data 4 Gnd Ground Note The maximum output supply current for each USB port on the server is 500 mA 139 Serial Connector The RJ 45 serial connector pins and their corresponding descriptions are shown in the figure and table in this section FIGURE D 2 Serial Connector TABLE D 2 Serial Connector Pinouts Pin Number Pin Name Description 1 RTS Ready to send 2 DTR Data terminal ready 3 TXD Transmit data 4 GND Ground 5 GND Ground 6 RXD Receive data 7 DSR Data send ready 8 CTS Clear to send 140 Netra X4200 M2 Server Service Manual May 2007 10 100BASE T
135. pendix E Serial Attached SCSI BIOS Configuration Utility 175 Advanced Device Properties Screen The Advanced Device Properties screen FIGURE E 12 allows you to view and modify infrequently accessed device settings TABLE E 9 describes the fields of the screen KREKKKKKKKEKKKK KK KKK KKK KKK KKK KKKK KKK KKK KK KKK KKK KKK KR KKK KEK KK KEKE KK KKKKKKKKKKKKKKKEKK LSI Logic MPT Setup Utility v6 02 00 00 2005 07 08 Advanced Device Properties SAS1064 i Maximum INT 13 devices for this adapter 24 k Maximum Target device spinups 1 k IO Timeout for Block Devices 10 i IO Timeout for Block Devices Removable 10 IO Timeout for Sequential Devices 10 i IO Timeout for Other devices 10 w LUNs to Scan for Block Devices A11 k LUNs to Scan for Block Devices Removable A11 7 LUNs to Scan for Sequential Devices A11 R z LUNs to Scan for Other Devices A11 x Removable Media support None Restore Defaults Esc Exit Menu F1 Shift 1 Help i Enter Select Item Change Item kkkkkkkkkkkxkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkk 176 Netra X4200 M2 Server Service Manual May 2007 TABLE E 9 FIGURE E 12 Advanced Device Properties Screen Advanced Device Properties Screen Field Descriptions Field Maximum INT 13 devices for this adapter Maximum target device spinups IO Timeout for Block Devices IO Timeout for Bl
136. r the Configuration Utility prompts you to save the changes before you exit the screen Appendix E Serial Attached SCSI BIOS Configuration Utility 161 From the Adapter List screen you can also press Alt N to access the Global Properties screen See FIGURE E 2 On this screen you can change global scope settings KREKEKKKKKKKE KKK KKK KKK KKK KKK KKK KKK KKK KKK KKK KKK KEK KKK KKE KK KKK KEKE KKK KKK KEKE KKKKKKKKKKEK LSI Logic MPT Setup Utility v6 02 00 00 2005 07 08 Adapter List Global Properties Adapter PCI PCI PCI PCI FW Revision Status Boot Bus Dev Fnc Slot Order SAS1064 02 03 00 00 1 04 00 00 IR Enabled 0 k k k Esc Exit Menu F1 Shift 1 Help Alt N Global Properties Alter Boot Order Ins Del Alter Boot List kkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkk FIGURE E 1 Adapter List Screen TABLE E 2 Adapter List Screen Field Descriptions Field Description Adapter The specific LSI Logic SAS controller type PCI Bus The PCI Bus number range 0x00 OxFF 0 255 decimal assigned by the system BIOS to an adapter PCI Dev The PCI Device range 0x00 0x1F 0 31 decimal assigned by the system BIOS to an adapter PCI Fne The PCI Function range 0x00 0x7 0 7 decimal assigned by the system BIOS to an adapter PCI Slot The PCI slot in which the controller is installed 162 Netra X4200 M2 Server
137. r The power supplies provide 3 3 VDC PSO PS Supply on page 95 standby power at 3 Amps and 12 VDC at 25 psj Amps When facing the rear of the system PSO is on the left and PS1 is on the right Chapter 1 Introduction to the Netra X4200 M2 Server 7 TABLE 1 2 Netra X4200 M2 Server FRU List Continued Item No FRU Replacement Instructions Description FRU Name 13 DIMM CPU Replacing the Duct aids cooling of DIMMS and CPU duct DIMM CPU Duct on page 68 14 Motherboard Replacing the The motherboard assembly is comprised of assembly Motherboard the following boards that must be replaced as Assembly on page 82 a single FRU e The CPU board Comprises the central MB processing subsystem for the server which includes the UltraSPARC T1 CPU processor 16 DIMM connectors the memory controllers and supporting circuitry e The I O board Provides the I O logic JOBD including the connectors for the PCI X and PCI E interfaces Ethernet interfaces all the power interconnections and miscellaneous logic Note This assembly is provided in different configurations to accommodate the different processor models 4 6 and 8 core 15 DIMMs Replacing Memory Can be ordered in the following sizes Modules DIMMs on e 1 GB page 71 e 2GB e 4GB 16 Battery Replacing the Battery BAT Battery on page 38 17 Graphics Replacing the GRASP Independent processor module that enables SP Redirectand Board on pag
138. r of the chassis see FIGURE 2 7 which shows the NMI Switch location on the Netra X4200 M2 server Chapter 2 Powering On and Configuring BIOS Settings 23 The Reset switch SW4 on the motherboard sends a reset order to the CPUs resetting the main system but not the service processor The button for this switch can be pushed by inserting a paper clip or similar stylus through the hole provided on the rear of the chassis see FIGURE 2 7 which shows the Reset switch location on the Netra X4200 M2 server NMI switch SW3 Reset switch SW4 FIGURE 2 7 NMI and Reset Switches on Rear Panel Updating the BIOS The BIOS is updated whenever you update the ILOM Service Processor firmware For instructions on updating the firmware refer to the Integrated Lights Out Manager Administration Guide 819 1160 Power On Self Test POST For information about BIOS POST testing POST codes POST code checkpoints and console redirection see Appendix B BIOS POST Codes on page 121 24 Netra X4200 M2 Server Service Manual May 2007 CHAPTER 3 Maintaining the Netra X4200 M2 Server This chapter contains information and procedures for servicing the Netra X4200 M2 server hardware including component removal and replacement procedures This chapter contains the following sections Tools and Supplies Ne
139. r on the motherboard for up to one minute To light the DIMM fault LEDs push the small button on the motherboard labeled DIMM SW2 See FIGURE 3 51 for the numbering and pairing of the Netra X4200 M2 DIMM slots Note To push the DIMM SW2 button the PCI Tray must be removed and the button must be pushed through the hole in the PCI E cable hold down bracket Netra X4200 M2 DIMM Population Rules The DIMM population rules for the Netra X4200 M2 server are as follows The Netra X4200 M2 server uses only DDR2 DIMMs Each CPU can support a maximum of four DDR2 DIMMs Each pair of DIMMs must be identical same manufacturer and capacity The DIMM slots are paired and the DIMMs must be installed in pairs A1 and B1 AO and BO The memory sockets are colored black or white to indicate which slots are paired by matching colors Netra X4200 M2 Server Service Manual May 2007 a CPUs with only a single pair of DIMMs must have those DIMMs installed in that CPU s white DIMM slots A1 and B1 DIMM SW2 DIMM AO DIMM BO Back panel of server DIMM A1 DIMM B1 Pair 0 DIMM B1 DIMM A1 Pair 1 DIMM BO DIMM AO Cable hold down bracket DIMM AO m DIMM BO m DIMM A1 DIMMBI1 DIMM fault LEDs in DIMM ejector levers FIGURE 3 51 Netra X4200 M2 DIMM Slot Numbering and Pairing Supported DIMM Configurations For Netra X4200 M2
140. r the following conditions e The array is inactive e The array is at its maximum number of devices e Integrated Striping firmware is used Striped Arrays do not support Hot Spares so no modifications can be made to an array once it is created Press Enter to synchronize the RAID array This field is grayed out under the following conditions e The array is inactive e The array does not need to be resynchronized e The adapter s MPT FW does not support the feature e Integrated Striping firmware is used This field is used to activate a RAID array This field is used to delete the currently displayed RAID array Exit Screen It is important to exit the SAS BIOS Configuration Utility correctly because some changes take effect only when you exit From the Adapter List press the Esc key to exit In addition a similar Exit screen appears when you exit most other screens and it can be used to save settings FIGURE E 18 shows the Exit screen Some options on the Exit screen might be grayed out indicating that they are not available at this time Appendix E Serial Attached SCSI BIOS Configuration Utility 191 KREKEKKKKKKKKKK KKK KK KKK KKK KKK KK KKK KKK KEK KK KKK KKK KKK KEK KEK KK KKK KK KKKKKKKKKKKKKKKKKKKK LSI Logic MPT Setup Utility v6 02 00 00 2005 07 08 ia Adapter and or device property changes have been made Cancel Exit Save changes then exit this menu Discard changes then exit this me
141. rver 67 Replacing the DIMM CPU Duct Removing the DIMM CPU Duct 1 Prepare the server for DIMM CPU duct removal See Powering Off the Server on page 28 Disconnecting Cables From the Server on page 29 Removing the Server From the Rack on page 30 Performing Antistatic Measures on page 31 Removing the Top Cover on page 33 Removing the PCI Tray and PCI E Ribbon Cables on page 34 2 Raise the DIMM CPU duct into the vertical position FIGURE 3 46 FIGURE 3 46 Raising the DIMM CPU Duct 68 Netra X4200 M2 Server Service Manual May 2007 3 Unhook the duct from the pins of the chassis FIGURE 3 47 FIGURE 3 47 Unhooking the DIMM CPU Duct From the Pins of the Chassis 4 Lift the duct out of the chassis and set it aside on an antistatic mat 5 Consider your next step a If you removed the DIMM CPU duct as part of another procedure return to that procedure a Otherwise continue to Installing the DIMM CPU Duct on page 69 Installing the DIMM CPU Duct 1 Remove the replacement DIMM CPU duct from its packaging 2 Position the duct vertically over the pins of the chassis and hook the duct to the pins of the chassis FIGURE 3 47 3 Lower the duct down to the horizontal position FIGURE 3 48 Chapter 3 Maintaining the Netra X4200 M2 Server 69 FIGURE 3 48 Lowering the DIMM CPU Duct 4 Consider your next step a If you installed the DIMM CPU duct as part of a
142. s Pin Number Signal Name pj DVD_DRST_L PS1_PRESENT_L DVD_DDATA 8 SAS_FAN_PRSNT_L DVD_DDATA 7 SAS_FAN_TACH DVD_DDATA 9 PS1_VIN_GOOD DVD_DDATA 6 PS1_POWEROK DVD_DDATA I10 eo ON DTD oO FF QO N Se me e V m 5 SP_I2C_DAT jai ies DVD_DDATA 5 SP_I2C_CLK a N Appendix D Connector Pinouts 147 TABLE D 8 Pin Number Flex Cable Motherboard Connector Pinouts Continued Signal Name 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 DVD_DDATA 11 GND DVD_DDATA 4 3 3 V AUX DVD_DDATA I12 PSO_PRESENT_L DVD_DDATAJ3 PSO_ENABLE_L DVD_DDATA I13 SAS_FAN_LED_L DVD_DDATA 2 PSO_VIN_GOOD DVD_DDATA 14 PSO_POWEROK DVD_DDATA 1 DVD_DDACK_L DVD_DDATA I15 DVD_DRDY DVD_DDRQ DVD_INT_L DVD_DDATA 0 GND DVD_DIOR_L SAS_DISK3_RX_P DVD_DIOW_L SAS_DISK3_RX_N DVD_DADDR 1 SAS_DISK1_RX_P DVD_PDIAG_L SAS_DISK1_RX_N 148 Netra X4200 M2 Server Service Manual May 2007 TABLE D 8 Pin Number Signal Name 45 DVD_DADDRJ 0 46 GND 47 DVD_DADDR 2 48 SAS_DISK3_TX_P 49 DVD_DCS1_L 50 SAS_DISK3_TX_N 51 DVD_DCS3_L 52 GND 53 DVD_DASP_L 54 SAS_DISK1_TX_P 55 5V 56 SAS_DISK1_TX_N 57 GND 58 GND 59 SAS_DISK2_TX_N 60 5V 61 SAS_DISK2_TX_P 62 GND 63 GND 64 GND 65 SAS_DISK2_TX_N 66 DISK3_ACT_LED_L 67 SAS_DISKO_TX_P 68 SPINDLE_IDO 69 GND 70 DISK2_ACT_LED_L 71 SAS_DISK2_RX_N 72 DISK1_ACT_LED_
143. s Toutes les marques SPARC sont utilis es sous licence et sont des marques de fabrique ou des marques d pos es de SPARC International Inc aux Etats Unis et dans d autres pays Les produits portant les marques SPARC sont bas s sur une architecture d velopp e par Sun Microsystems Inc AMD Opteron est une marque de fabrique ou une marque deposee de Advanced Microdevices Inc L interface d utilisation graphique OPEN LOOK et Sun a t d velopp e par Sun Microsystems Inc pour ses utilisateurs et licenci s Sun reconna t les efforts de pionniers de Xerox pour la recherche et le d veloppement du concept des interfaces d utilisation visuelle ou graphique pour l industrie de Vinformatique Sun d tient une license non exclusive de Xerox sur l interface d utilisation grephique Xerox cette licence couvrant galement les licenci es de Sun qui mettent en place l interface d utilisation graphique OPEN LOOK et qui en outre se conforment aux licences crites de Sun LA DOCUMENTATION EST FOURNIE EN L TAT ET TOUTES AUTRES CONDITIONS DECLARATIONS ET GARANTIES EXPRESSES OU TACITES SONT FORMELLEMENT EXCLUES DANS LA MESURE AUTORISEE PAR LA LOI APPLICABLE Y COMPRIS NOTAMMENT TOUTE GARANTIE IMPLICITE RELATIVE A LA QUALITE MARCHANDE A L APTITUDE A UNE UTILISATION PARTICULIERE OU A L ABSENCE DE CONTREFA ON Qa Adobe PostScript Contents Preface xi Introduction to the Netra X4200 M2 Server 1 Features of the Server 1 Netra
144. seven top level BIOS Setup screens TABLE 2 2 BIOS Setup Screens Summary Screen Description Main General system information Advanced Configuration interface for the CPUs IDE SuperlO ACPI Event Log HyperTransport IPMI MPS PCI Express Confiuration PowerNow Remote Access and USB PCI PnP Configure Plug and Play PnP devices by the BIOS default or by the operating system if applicable Boot Configure the boot device priority hard disk drives and the ATAPI DVD drive Security Install or change the user and supervisor passwords Chipset Configuration options for the NorthBridge and SouthBridge devices and PCI X devices Note that the Memory Chipkill option is enabled by default Enabling Chipkill improves system reliability but degrades system performance under specific applications Exit Save or discard changes FIGURE 2 5 summarizes the BIOS menu tree Netra X4200 M2 Server Service Manual May 2007 Main menu Advanced menu CPU Configuration IDE Configuration Super I O Configuration PCI PnP menu Boot Settings Security Boot menu menu Boot Device Priority Hard Disk Drives ACPI Settings Event Logging HyperTransport Configuration ACPI Configuration IPMI BMC Configuration Event Log PCI Express A LAN ae Configuration MPS F PEF Configuration Configuratio
145. sion MPT SAS BIOS Overview 157 Boot Initialization With BIOS Boot Specification BBS 158 Starting the SAS BIOS Configuration Utility 158 Configuration Utility Screens 159 User Input Keys 160 Adapter List Screen 160 Global Properties Screen 164 Adapter Properties Screen 165 SAS Topology Screen 167 Device Properties Screen 170 Device Verify Screen 172 Advanced Adapter Properties Screen 173 Advanced Device Properties Screen 176 PHY Properties Screen 179 Integrated RAID Configuration and Management Screens 182 Select New Array Type Screen 182 Create New Array Screen 183 View Array Screen 187 Manage Array Screen 189 Exit Screen 191 RAID Implementation and Support 192 Automatic Data Resynchronization and Hot Spares 193 RAID Level Support 194 RAID Volume Support 194 RAID Combination Support 194 Performing RAID Configuration Tasks 195 viii Netra X4200 M2 Server Service Manual May 2007 Creating a RAID 0 Volume 195 Creating a RAID 1 Volume 196 Managing Hot Spares 197 Creating a Second RAID Volume 198 Viewing RAID Volume Properties 198 Synchronizing an Array 199 Activating an Array 199 Deleting an Array 199 Locating a Disk Drive 200 Index 201 Contents ix x Netra X4200 M2 Server Service Manual May 2007 Preface This Netra X4200 M2 Server Service Manual contains information and procedures for maintaining and upgrading the Netra X4200 M2 server Before You Read This Document It is important that you review the s
146. t Do not remove the Sun logo The Option ROM output is not displayed Boot Num Lock This option is On by default keyboard Num Lock is turned on during boot If you set this to off the keyboard Num Lock is not turned on during boot Wait for F1 if Error This option is disabled by default If you enable this the system will pause if an error is found during POST and will only resume when you press the F1 key Interrupt 19 Capture This option is reserved for future use Do not change Default Boot Order The letters in the brackets represent the boot devices To see the letters defined position your cursor over the field and read the definition in the right side of the screen AppendixB BIOS POST Codes 123 POST Codes TABLE B 1 contains descriptions of each of the POST codes listed in the same order in which they are generated These POST codes appear as a four digit string that is a combination of two digit output from primary I O port 80 and two digit output from secondary I O port 81 In the POST codes listed in TABLE B 1 the first two digits are from port 81 and the last two digits are from port 80 TABLE B 1 POST Codes Post Code Description 00d0 Coming out of POR PCI configuration space initialization Enabling 8111 s SMBus 00d1 Keyboard controller BAT Waking up from PM Saving power on CPUID in scratch CMOS 00d2 Disable cache full memory sizing and verify that flat mode is enabled 00d3 Memory detections a
147. t sequences since the last PHY Link Error Reset The count stops when it reaches the maximum value Loss of DWORD Sync The number of times since the last PHY Link Error Reset that DWORD synchronization was lost and the link reset sequence occurred The count stops when it reaches the maximum value Running Disparity Errors The number of DWORDs with running disparity errors that have been received outside of PHY reset sequences since the last PHY Link Error Reset The count stops when it reaches the maximum value PHY Reset Errors The number of times the PHY reset sequence has failed since the last PHY Link Error Reset The count stops when it reaches the maximum value Link Error Count Actual link error count values since the last PHY Link Error Reset The counts stop when they reach their maximum value Appendix E Serial Attached SCSI BIOS Configuration Utility 181 TABLE E 10 PHY Properties Screen Field Descriptions Continued Field Description Threshold Count Link error count threshold values When a Link Error Count exceeds a Threshold Count within the Threshold Time secs the Fusion MPT FW may reduce the link rate Threshold Time Time in seconds over which to apply Threshold Count When a secs Link Error Count exceeds a Threshold Count within the Threshold Time secs the Fusion MPT FW may reduce the link rate Reset Link Error Press Enter to reset the Link Error Counts for this PHY or all PHYs
148. tain components that are extremely sensitive to static electricity 3 Disconnect both power cords from the server s power supplies 4 Turn off all peripheral devices connected to the system server 5 Label any peripheral cables and or telecommunication lines that must be disconnected in order to remove and replace a specific component 6 Remove the server from the rack See Removing the Server From the Rack on page 30 Removing the Server From the Rack Caution The server weighs approximately 40 lb 18 kg Two people are required 30 to dismount and carry the chassis 1 Disconnect all the cables and power cords from the server 2 From the front of the server release the slide rail latches on each side Pinch the green latches as shown in FIGURE 3 3 Netra X4200 M2 Server Service Manual May 2007 FIGURE 3 3 Slide Release Latches 3 While pinching the release latches slowly pull the server forward until the slide rails latch Caution The server weighs approximately 40 lb 18 kg The next step requires two people to dismount and carry the chassis 4 From the front of the server pull the release tabs forward and pull the server forward until it is free of the rack rails The release tabs are located on each rail about midway on the server 5 Set the server on a sturdy work surface 6 Perform antistatic measures See Performing Antistatic Measures on page 31
149. term 5 to 55 C 25 113 F 5 to 90 relative humidity noncondensing but not to exceed 0 024 kg water kg dry air 0 0531b dry air Operating altitude 0 10 000 feet 0 3048 m TABLE A 4 contains the declared noise emissions in accordance with ISO 9296 A weighted operating and idling TABLE A 4 Netra X4200 M2 Acoustic Noise Emission Specifications Specification Value Lyad at or below 77 F 25 C 7 8B 1 B 10 dB Lag at max ambient 8 3 B W 1 B 10 dB Lp Am Pystander at or below 77 F 25 C 63 dB L HAD at max ambient 67 dB 120 Netra X4200 M2 Servers Service Manual May 2007 APPENDIX B BIOS POST Codes Power On Self Test POST The system BIOS provides a rudimentary power on self test POST The basic devices required for the server to operate are checked memory is tested the LSI 1064 disk controller and attached disks are probed and enumerated and the onboard network controllers are initialized The progress of the self test is indicated by a series of POST codes These codes are displayed at the bottom right corner of the system s VGA screen once the self test has progressed far enough to initialize the video monitor However the codes are displayed as the self test runs and scroll off of the screen too quickly to be read An alternate method of displaying the POST codes is to redirect the output of the console to a serial port see Redirecting Console Output on page
150. the Netra X4200 M2 Server 57 58 Replacing the Hard Drive Fan Assembly Caution Netra X4200 M2 fans are not hot swappable you must power off ther server before replacing Do not operate the server without fans Note This fan assembly is also referred to as Fan Tray 1 Removing the Hard Drive Fan Assembly 1 Prepare the server for hard drive fan removal See Powering Off the Server on page 28 Disconnecting Cables From the Server on page 29 Removing the Server From the Rack on page 30 Performing Antistatic Measures on page 31 Removing the Top Cover on page 33 Netra X4200 M2 Server Service Manual May 2007 2 Disconnect the hard drive fan assembly cable from the power board connector FIGURE 3 34 Disconnecting the Hard Drive Fan Assembly Cable 3 Carefully lift the hard drive fan assembly cable from the cable guides 4 Push the green release button on the center of the hard drive fan bracket and pivot the bracket backward FIGURE 3 35 FIGURE 3 35 Releasing the Hard Drive Fan Bracket 5 Slide the bracket forward and lift the hard drive fan assembly from the chassis Chapter 3 Maintaining the Netra X4200 M2 Server 59 FIGURE 3 36 FIGURE 3 36 Lifting the Hard Drive Fan Assembly From the Chassis 6 Set the hard drive fan assembly aside on an antistatic mat 7 Continue to Installing the Hard Drive Fan Assembly on page 60 Installing the Hard Drive Fan
151. the cover If you cannot safely view and access the component remove the server from the rack 3 Remove the cover as described in Removing the Top Cover on page 33 Caution There is a power status LED CR1 on the GRASP board that indicates whether 3 3V standby power is reaching the GRASP board The GRASP board is not hot pluggable and should never be removed while this LED is lit 4 Squeeze the plastic standoff that protrudes through the GRASP board to press the standoff s locking tabs See procedure inset 1 in FIGURE 3 45 If you have difficulty pressing the locking tabs with your fingers you can use a pair of long nosed pliers 66 Netra X4200 M2 Server Service Manual May 2007 Power status LED CR1 ys 43 FIGURE 3 45 Removing the GRASP Board From the Motherboard 5 Raise the corner of the GRASP board until it is clear of the locking tab See Procedure 2 in FIGURE 3 45 6 Pivot the front edge of the GRASP board upward to disengage it from the rear plastic bracket and to disengage its connector from the motherboard See Procedure 3 in FIGURE 3 45 Note Gently lift to avoid bending the GRASP board while removing or installing Installing the GRASP Board To install the GRASP board reverse the steps you used to remove the GRASP board Push firmly on the center of the board to avoid bowing and ensure full mating of the motherboard connector Chapter 3 Maintaining the Netra X4200 M2 Se
152. the most up to date list of replaceable components product updates and downloads go to http www sun com netra x4200 1 Power off the server as described in Powering Off the Server on page 28 2 If the server is in a rack slide it far enough from the rack so that you can remove the cover If you cannot safely view and access the component remove the server from the rack 3 Remove the cover of the assembly as described in Removing the Top Cover on page 33 Note Record the orientation polarity of the battery in its holder before you remove it The positive polarity marked with a symbol should be facing toward the chassis center 38 Netra X4200 M2 Server Service Manual May 2007 4 Remove the battery by gently pulling the clip away from the battery face and lifting the battery straight up FIGURE 3 11 facing chassis center Ss FIGURE 3 11 Removing the Battery 5 Installation is the reverse of this procedure Note Install the new battery in the holder with the same orientation polarity as the battery that you removed The positive polarity marked with a symbol should be facing toward the chassis center Chapter 3 Maintaining the Netra X4200 M2 Server 39 Replacing the DVD Drive Note All FRUs are customer replaceable Removing the DVD Drive T Prepare the server for optical media drive removal See m Powering Off the Server o
153. two disk mirror and is operating properly e Secondary Disk is the secondary disk for a two disk mirror and is operating properly e Wrg Type Device is not compatible for use as part of a RAID array e Too Small Disk is too small to mirror existing data e Max Dsks Maximum number of disks allowed for this type of array reached or Maximum number of total IR disks on a controller reached e No SMART Disk does not support SMART cannot be used in an array Wrg Intfc Device interface SAS differs from existing IR disks Pred Fail Indicates whether SMART is predicting device failure Yes or No Size MB The size of the device in Mbytes 1 Mbyte 1024 x 1024 1 048 576 bytes If the device is part of a two disk array this field reflects the size of the array not the size of the individual disk If the device is part of an array of three or more disks this field is the size that the disk makes up within the array Note When creating a striped array the usable size of the array is determined by the number of drives multiplied by the size of the smallest drive in the array In arrays consisting of different sized drives excess space on larger drives is unusable Manage Array Screen The Manage Array screen is used to manage the current array as shown in FIGURE E 17 TABLE E 13 describes the fields of the screen If you select Manage Hot Spare the utility displays a hot spare management screen that has the same l
154. ume on page 196 3 After you select the hot spare disk press C 4 Select Save Changes then exit this menu to commit the changes The Configuration Utility will pause while the hot spare is being added Appendix E Serial Attached SCSI BIOS Configuration Utility 197 Follow these steps to delete a hot spare from a RAID 1 volume 1 Select Manage Hot Spare 2 Remove the current hot spare disk from the list by pressing the key key or space bar 3 After you clear the hot spare press C 4 Select Save Changes then exit this menu to commit the changes The Configuration Utility will pause while the hot spare is being removed Creating a Second RAID Volume The LSI Logic SAS controllers support two active RAID volumes If one volume is already configured follow these steps to add a second volume 1 In the Configuration Utility select an adapter from the Adapter List screen 2 Select the RAID Properties option This displays the current volume 3 Press C to create a new volume 4 Create the new volume To create a second RAID 0 volume continue with Step 2 of Creating a RAID 0 Volume on page 195 a To create a second RAID 1 volume continue with Step 2 of Creating a RAID 1 Volume on page 196 Viewing RAID Volume Properties Follow these steps to view the properties of RAID volumes 1 In the Configuration Utility select an adapter from the Adapter List screen 2 Select the RAID Prop
155. xisting data e Max Dsks Maximum number of disks allowed for this type of array is reached or Maximum number of total IR disks on a controller is reached e No SMART Disk does not support SMART cannot be used in an array e Wrg Intfc Device interface SAS differs from existing IR disks Pred Fail Indicates whether SMART is predicting device failure Yes or No Size MB The size of the device in Mbytes 1 Mbyte 1024 x 1024 1 048 576 bytes If the device is part of a two disk array this field reflects the size of the array not the size of the individual disk If the device is part of an array of three or more disks this field is the size that the disk makes up within the array Note When creating a striped array the usable size of the array is determined by the number of drives multiplied by the size of the smallest drive in the array In arrays consisting of different sized drives excess space on larger drives is unusable 186 Netra X4200 M2 Server Service Manual May 2007 View Array Screen The View Array screen allows you to view the current array configuration as shown in FIGURE E 16 Press Alt N to view the next array Press C to create a new array TABLE E 12 describes the fields of the screen KEKKKKKKKKE KKK KKK KKK KKK KKK KKK KKK KKK KKK KKK KKK KKK KKK KEK KKK KKK KEK KKK KKKKRKKEKKKKKKKKKKKK View Array SAS1064 Array Identifier Type Scan Order Size MB Status Manage Array Scan Dev

Netra X4200 M2 Server Service Manual

Contents

Download Pdf Manuals

Related Search

Related Contents